Contenu | Rechercher | Menus

Annonce

Si vous avez des soucis pour rester connecté, déconnectez-vous puis reconnectez-vous depuis ce lien en cochant la case
Me connecter automatiquement lors de mes prochaines visites.

À propos de l'équipe du forum.

#1 Le 07/10/2015, à 18:43

domi301

[RESOLU]connection réseau éthernet impossible intel PRO/100

salut

j'ai déterré un vieux portable compaq presario 2800 (datant de 2003-2004...)
la connection réseau marchait bien sous windows XP

pour le rajeunir je suis reparti sous lubuntu en fresh install 15.10 tant qu'a faire
Linux Presario-2800 4.2.0-12-generic #14-Ubuntu SMP Mon Sep 28 18:35:30 UTC 2015 i686 i686 i686 GNU/Linux

mais impossible d'activer le réseau
(ca ne vient ni du cable ni du switch... et a priori pas de la machine vu que ca marchait en windows)
j'ai aussi essayé avec une xubuntu 14.04 mais meme blocage

en mode graphique je n'ai carrement pas d'interface reseau disponible
et si je la cree il me la supprime au reboot...

cat /etc/network/in*s

# interfaces(5) file used by ifup(8) and ifdown(8)
auto lo
iface lo inet loopback


sous le terminal le materiel semble etre bien la pourtant
==>
sudo lshw -C network

 *-network NON-RÉCLAMÉ
       description: Ethernet controller
       produit: 82801CAM (ICH3) PRO/100 VE (LOM) Ethernet Controller
       fabriquant: Intel Corporation
       identifiant matériel: 8
       information bus: pci@0000:02:08.0
       version: 42
       bits: 32 bits
       horloge: 33MHz
       fonctionnalités: pm cap_list
       configuration: latency=66 maxlatency=56 mingnt=8
       ressources: mémoire:40100000-40100fff portE/S:2000(taille=64)

et ifconfig -a  semble montrer des echanges ???

lo        Link encap:Boucle locale  
          inet adr:127.0.0.1  Masque:255.0.0.0
          adr inet6: ::1/128 Scope:Hôte
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          Packets reçus:592 erreurs:0 :0 overruns:0 frame:0
          TX packets:592 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 lg file transmission:0 
          Octets reçus:47200 (47.2 KB) Octets transmis:47200 (47.2 KB)

voici quelques logs si ca peut vous inspirer  des idées

dmesg

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.2.0-12-generic (buildd@lcy01-12) (gcc version 5.2.1 20150922 (Ubuntu 5.2.1-18ubuntu1) ) #14-Ubuntu SMP Mon Sep 28 18:35:30 UTC 2015 (Ubuntu 4.2.0-12.14-generic 4.2.1)
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   NSC Geode by NSC
[    0.000000]   Cyrix CyrixInstead
[    0.000000]   Centaur CentaurHauls
[    0.000000]   Transmeta GenuineTMx86
[    0.000000]   Transmeta TransmetaCPU
[    0.000000]   UMC UMC UMC UMC
[    0.000000] x86/fpu: Legacy x87 FPU detected.
[    0.000000] x86/fpu: Using 'lazy' FPU context switches.
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000002ffcffff] usable
[    0.000000] BIOS-e820: [mem 0x000000002ffd0000-0x000000002fff0bff] reserved
[    0.000000] BIOS-e820: [mem 0x000000002fff0c00-0x000000002fffbfff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x000000002fffc000-0x000000002fffffff] reserved
[    0.000000] Notice: NX (Execute Disable) protection missing in CPU!
[    0.000000] SMBIOS 2.3 present.
[    0.000000] DMI: Compaq  Presario 2800                   /07D8, BIOS 68P4M Ver. F.24 06/17/2005
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] e820: last_pfn = 0x2ffd0 max_arch_pfn = 0x1000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-CFFFF write-protect
[    0.000000]   D0000-EFFFF uncachable
[    0.000000]   F0000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask FE0000000 write-back
[    0.000000]   1 base 020000000 mask FF0000000 write-back
[    0.000000]   2 disabled
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WC  UC- UC  
[    0.000000] Scanning 1 areas for low memory corruption
[    0.000000] initial memory mapped: [mem 0x00000000-0x021fffff]
[    0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[    0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[    0.000000]  [mem 0x00000000-0x000fffff] page 4k
[    0.000000] init_memory_mapping: [mem 0x2fc00000-0x2fdfffff]
[    0.000000]  [mem 0x2fc00000-0x2fdfffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x20000000-0x2fbfffff]
[    0.000000]  [mem 0x20000000-0x2fbfffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x00100000-0x1fffffff]
[    0.000000]  [mem 0x00100000-0x001fffff] page 4k
[    0.000000]  [mem 0x00200000-0x1fffffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x2fe00000-0x2ffcffff]
[    0.000000]  [mem 0x2fe00000-0x2ffcffff] page 4k
[    0.000000] BRK [0x01cad000, 0x01cadfff] PGTABLE
[    0.000000] BRK [0x01cae000, 0x01caefff] PGTABLE
[    0.000000] RAMDISK: [mem 0x2d058000-0x2ef93fff]
[    0.000000] ACPI: Early table checksum verification disabled
[    0.000000] ACPI: RSDP 0x00000000000F60E0 000014 (v00 COMPAQ)
[    0.000000] ACPI: RSDT 0x000000002FFF0C84 000030 (v01 COMPAQ CPQ004A  17060520 CPQ  00000001)
[    0.000000] ACPI: FACP 0x000000002FFF0C00 000084 (v02 COMPAQ CPQ004A  00000002 CPQ  00000001)
[    0.000000] ACPI: DSDT 0x000000002FFF0CB4 005D04 (v01 COMPAQ EVON800  00010000 MSFT 0100000E)
[    0.000000] ACPI: FACS 0x000000002FFFBE80 000040
[    0.000000] ACPI: SSDT 0x000000002FFF69B8 00010E (v01 COMPAQ CPQGysr  00001001 MSFT 0100000E)
[    0.000000] ACPI: SSDT 0x000000002FFF6AC6 000165 (v01 COMPAQ CPQMag   00001001 MSFT 0100000E)
[    0.000000] 0MB HIGHMEM available.
[    0.000000] 767MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 2ffd0000
[    0.000000]   low ram: 0 - 2ffd0000
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000001000-0x0000000000ffffff]
[    0.000000]   Normal   [mem 0x0000000001000000-0x000000002ffcffff]
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000001000-0x000000000009efff]
[    0.000000]   node   0: [mem 0x0000000000100000-0x000000002ffcffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000002ffcffff]
[    0.000000] On node 0 totalpages: 196462
[    0.000000]   DMA zone: 40 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 3998 pages, LIFO batch:0
[    0.000000]   Normal zone: 1880 pages used for memmap
[    0.000000]   Normal zone: 192464 pages, LIFO batch:31
[    0.000000] Using APIC driver default
[    0.000000] ACPI: PM-Timer IO Port: 0x1008
[    0.000000] smpboot: Allowing 1 CPUs, 0 hotplug CPUs
[    0.000000] Local APIC disabled by BIOS -- you can enable it with "lapic"
[    0.000000] APIC: disable apic facility
[    0.000000] APIC: switched to apic NOOP
[    0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[    0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[    0.000000] e820: [mem 0x30000000-0xffffffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
[    0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:1 nr_node_ids:1
[    0.000000] PERCPU: Embedded 19 pages/cpu @ef5a2000 s47116 r0 d30708 u77824
[    0.000000] pcpu-alloc: s47116 r0 d30708 u77824 alloc=19*4096
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 194542
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.2.0-12-generic root=UUID=0c4f4e34-7f4b-4ab4-9302-530b807b872b ro quiet splash vt.handoff=7
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Initializing CPU#0
[    0.000000] Initializing HighMem for node 0 (00000000:00000000)
[    0.000000] Memory: 729580K/785848K available (7393K kernel code, 742K rwdata, 3020K rodata, 920K init, 792K bss, 56268K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] virtual kernel memory layout:
                   fixmap  : 0xfff15000 - 0xfffff000   ( 936 kB)
                   pkmap   : 0xffc00000 - 0xffe00000   (2048 kB)
                   vmalloc : 0xf07d0000 - 0xffbfe000   ( 244 MB)
                   lowmem  : 0xc0000000 - 0xeffd0000   ( 767 MB)
                     .init : 0xc1ae8000 - 0xc1bce000   ( 920 kB)
                     .data : 0xc1738870 - 0xc1ae6840   (3767 kB)
                     .text : 0xc1000000 - 0xc1738870   (7394 kB)
[    0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.000000] SLUB: HWalign=128, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	Build-time adjustment of leaf fanout to 32.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=1
[    0.000000] NR_IRQS:2304 nr_irqs:32 16
[    0.000000] CPU 0 irqstacks, hard=ef032000 soft=ef034000
[    0.000000] vt handoff: transparent VT on vt#7
[    0.000000] Console: colour dummy device 80x25
[    0.000000] console [tty0] enabled
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] tsc: Detected 1894.051 MHz processor
[    0.008029] Calibrating delay loop (skipped), value calculated using timer frequency.. 3788.10 BogoMIPS (lpj=7576204)
[    0.008040] pid_max: default: 32768 minimum: 301
[    0.008057] ACPI: Core revision 20150619
[    0.021368] ACPI: All ACPI Tables successfully acquired
[    0.021383] ACPI: setting ELCR to 0200 (from 0c20)
[    0.021432] Security Framework initialized
[    0.021464] AppArmor: AppArmor initialized
[    0.021469] Yama: becoming mindful.
[    0.021574] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.021581] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.022107] Initializing cgroup subsys blkio
[    0.022118] Initializing cgroup subsys memory
[    0.022141] Initializing cgroup subsys devices
[    0.022150] Initializing cgroup subsys freezer
[    0.022158] Initializing cgroup subsys net_cls
[    0.022166] Initializing cgroup subsys perf_event
[    0.022174] Initializing cgroup subsys net_prio
[    0.022182] Initializing cgroup subsys hugetlb
[    0.022229] CPU0: Hyper-Threading is disabled
[    0.022242] mce: CPU supports 4 MCE banks
[    0.022278] Last level iTLB entries: 4KB 64, 2MB 64, 4MB 64
[    0.022283] Last level dTLB entries: 4KB 64, 2MB 0, 4MB 64, 1GB 0
[    0.049409] Freeing SMP alternatives memory: 28K (c1bce000 - c1bd5000)
[    0.056025] ftrace: allocating 30193 entries in 59 pages
[    0.076283] smpboot: weird, boot CPU (#0) not listed by the BIOS
[    0.076293] smpboot: SMP motherboard not detected
[    0.076295] smpboot: SMP disabled
[    0.076300] smpboot: Local APIC not detected. Using dummy APIC emulation.
[    0.076367] Performance Events: Netburst events, 
[    0.076386] no APIC, boot with the "lapic" boot parameter to force-enable it.
[    0.076389] no hardware sampling interrupt available.
[    0.076396] Netburst P4/Xeon PMU driver.
[    0.076402] ... version:                0
[    0.076404] ... bit width:              40
[    0.076407] ... generic registers:      18
[    0.076410] ... value mask:             000000ffffffffff
[    0.080012] ... max period:             0000007fffffffff
[    0.080015] ... fixed-purpose events:   0
[    0.080018] ... event mask:             000000000003ffff
[    0.082041] x86: Booted up 1 node, 1 CPUs
[    0.082049] smpboot: Total of 1 processors activated (3788.10 BogoMIPS)
[    0.082181] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[    0.082400] devtmpfs: initialized
[    0.083047] evm: security.selinux
[    0.083051] evm: security.SMACK64
[    0.083054] evm: security.SMACK64EXEC
[    0.083056] evm: security.SMACK64TRANSMUTE
[    0.083059] evm: security.SMACK64MMAP
[    0.083061] evm: security.ima
[    0.083064] evm: security.capability
[    0.083262] PM: Registering ACPI NVS region [mem 0x2fff0c00-0x2fffbfff] (46080 bytes)
[    0.083451] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.083609] pinctrl core: initialized pinctrl subsystem
[    0.083885] RTC time:  5:33:58, date: 10/07/15
[    0.084244] NET: Registered protocol family 16
[    0.084774] EISA bus registered
[    0.084785] cpuidle: using governor ladder
[    0.084793] cpuidle: using governor menu
[    0.084939] clocksource: pit: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1601818034827 ns
[    0.085014] ACPI: bus type PCI registered
[    0.085021] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.087389] PCI: PCI BIOS revision 2.10 entry at 0xf031f, last bus=3
[    0.087393] PCI: Using configuration type 1 for base access
[    0.092100] ACPI: Added _OSI(Module Device)
[    0.092106] ACPI: Added _OSI(Processor Device)
[    0.092110] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.092114] ACPI: Added _OSI(Processor Aggregator Device)
[    0.121555] ACPI : EC: EC started
[    0.121882] ACPI: Interpreter enabled
[    0.121882] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20150619/hwxface-580)
[    0.121882] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20150619/hwxface-580)
[    0.121882] ACPI: (supports S0 S3 S4 S5)
[    0.121882] ACPI: Using PIC for interrupt routing
[    0.121882] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.127250] ACPI: Power Resource [C155] (off)
[    0.128304] ACPI: Power Resource [C169] (off)
[    0.129211] ACPI: Power Resource [C16D] (off)
[    0.129678] ACPI: Power Resource [C171] (off)
[    0.130523] ACPI: Power Resource [C17A] (on)
[    0.136829] ACPI: Power Resource [C0E3] (on)
[    0.139112] ACPI: Power Resource [C1EB] (off)
[    0.139243] ACPI: Power Resource [C1EC] (off)
[    0.139370] ACPI: Power Resource [C1ED] (off)
[    0.139504] ACPI: Power Resource [C1EE] (off)
[    0.146920] ACPI: PCI Root Bridge [C046] (domain 0000 [bus 00-ff])
[    0.146935] acpi PNP0A03:00: _OSC: OS supports [ASPM ClockPM Segments MSI]
[    0.146949] acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
[    0.153209] acpi PNP0A03:00: fail to add MMCONFIG information, can't access extended PCI configuration space under this bridge.
[    0.153490] PCI host bridge to bus 0000:00
[    0.153498] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.153504] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7 window]
[    0.153510] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    0.153515] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    0.153521] pci_bus 0000:00: root bus resource [mem 0x30000000-0xffffffff window]
[    0.153526] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000dffff window]
[    0.153548] pci 0000:00:00.0: [8086:1a30] type 00 class 0x060000
[    0.153573] pci 0000:00:00.0: reg 0x10: [mem 0x60000000-0x6fffffff pref]
[    0.153779] pci 0000:00:01.0: [8086:1a31] type 01 class 0x060400
[    0.154009] pci 0000:00:1e.0: [8086:2448] type 01 class 0x060400
[    0.154133] pci 0000:00:1e.0: System wakeup disabled by ACPI
[    0.154248] pci 0000:00:1f.0: [8086:248c] type 00 class 0x060100
[    0.154348] pci 0000:00:1f.0: can't claim BAR 13 [io  0x1000-0x107f]: address conflict with ACPI CPU throttle [io  0x1010-0x1015]
[    0.154358] pci 0000:00:1f.0: quirk: [io  0x1100-0x113f] claimed by ICH4 GPIO
[    0.154519] pci 0000:00:1f.1: [8086:248a] type 00 class 0x01018a
[    0.154546] pci 0000:00:1f.1: reg 0x10: [io  0x0000-0x0007]
[    0.154561] pci 0000:00:1f.1: reg 0x14: [io  0x0000-0x0003]
[    0.154576] pci 0000:00:1f.1: reg 0x18: [io  0x0000-0x0007]
[    0.154590] pci 0000:00:1f.1: reg 0x1c: [io  0x0000-0x0003]
[    0.154605] pci 0000:00:1f.1: reg 0x20: [io  0x4440-0x444f]
[    0.154621] pci 0000:00:1f.1: reg 0x24: [mem 0x00000000-0x000003ff]
[    0.154640] pci 0000:00:1f.1: legacy IDE quirk: reg 0x10: [io  0x01f0-0x01f7]
[    0.154644] pci 0000:00:1f.1: legacy IDE quirk: reg 0x14: [io  0x03f6]
[    0.154649] pci 0000:00:1f.1: legacy IDE quirk: reg 0x18: [io  0x0170-0x0177]
[    0.154653] pci 0000:00:1f.1: legacy IDE quirk: reg 0x1c: [io  0x0376]
[    0.154826] pci 0000:00:1f.5: [8086:2485] type 00 class 0x040100
[    0.154850] pci 0000:00:1f.5: reg 0x10: [io  0x4000-0x40ff]
[    0.154866] pci 0000:00:1f.5: reg 0x14: [io  0x4400-0x443f]
[    0.155171] pci 0000:01:00.0: [1002:4c57] type 00 class 0x030000
[    0.155203] pci 0000:01:00.0: reg 0x10: [mem 0x48000000-0x4fffffff pref]
[    0.155217] pci 0000:01:00.0: reg 0x14: [io  0x3000-0x30ff]
[    0.155231] pci 0000:01:00.0: reg 0x18: [mem 0x40300000-0x4030ffff]
[    0.155267] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0001ffff pref]
[    0.155299] pci 0000:01:00.0: supports D1 D2
[    0.155462] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.155470] pci 0000:00:01.0:   bridge window [io  0x3000-0x3fff]
[    0.155477] pci 0000:00:01.0:   bridge window [mem 0x40300000-0x403fffff]
[    0.155484] pci 0000:00:01.0:   bridge window [mem 0x48000000-0x4fffffff pref]
[    0.155669] pci 0000:02:04.0: [14f1:2f00] type 00 class 0x078000
[    0.155701] pci 0000:02:04.0: reg 0x10: [mem 0x40000000-0x4000ffff]
[    0.155715] pci 0000:02:04.0: reg 0x14: [io  0x2040-0x2047]
[    0.155791] pci 0000:02:04.0: PME# supported from D3hot
[    0.155961] pci 0000:02:06.0: [104c:ac50] type 02 class 0x060700
[    0.155995] pci 0000:02:06.0: reg 0x10: [mem 0x40080000-0x40080fff]
[    0.156043] pci 0000:02:06.0: supports D1 D2
[    0.156048] pci 0000:02:06.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.156216] pci 0000:02:08.0: [8086:1031] type 00 class 0x020000
[    0.156248] pci 0000:02:08.0: reg 0x10: [mem 0x40100000-0x40100fff]
[    0.156263] pci 0000:02:08.0: reg 0x14: [io  0x2000-0x203f]
[    0.156339] pci 0000:02:08.0: supports D1 D2
[    0.156345] pci 0000:02:08.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.156403] pci 0000:02:08.0: System wakeup disabled by ACPI
[    0.156527] pci 0000:02:0e.0: [1033:0035] type 00 class 0x0c0310
[    0.156559] pci 0000:02:0e.0: reg 0x10: [mem 0x40180000-0x40180fff]
[    0.156644] pci 0000:02:0e.0: supports D1 D2
[    0.156649] pci 0000:02:0e.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.156706] pci 0000:02:0e.0: System wakeup disabled by ACPI
[    0.156820] pci 0000:02:0e.1: [1033:0035] type 00 class 0x0c0310
[    0.156851] pci 0000:02:0e.1: reg 0x10: [mem 0x40200000-0x40200fff]
[    0.156937] pci 0000:02:0e.1: supports D1 D2
[    0.156942] pci 0000:02:0e.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.156998] pci 0000:02:0e.1: System wakeup disabled by ACPI
[    0.157115] pci 0000:02:0e.2: [1033:00e0] type 00 class 0x0c0320
[    0.157147] pci 0000:02:0e.2: reg 0x10: [mem 0x40280000-0x402800ff]
[    0.157232] pci 0000:02:0e.2: supports D1 D2
[    0.157237] pci 0000:02:0e.2: PME# supported from D0 D1 D2 D3hot D3cold
[    0.157293] pci 0000:02:0e.2: System wakeup disabled by ACPI
[    0.157428] pci 0000:00:1e.0: PCI bridge to [bus 02-03] (subtractive decode)
[    0.157438] pci 0000:00:1e.0:   bridge window [io  0x2000-0x2fff]
[    0.157446] pci 0000:00:1e.0:   bridge window [mem 0x40000000-0x402fffff]
[    0.157455] pci 0000:00:1e.0:   bridge window [io  0x0000-0x0cf7 window] (subtractive decode)
[    0.157460] pci 0000:00:1e.0:   bridge window [io  0x0d00-0xffff window] (subtractive decode)
[    0.157465] pci 0000:00:1e.0:   bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode)
[    0.157470] pci 0000:00:1e.0:   bridge window [mem 0x30000000-0xffffffff window] (subtractive decode)
[    0.157475] pci 0000:00:1e.0:   bridge window [mem 0x000d0000-0x000dffff window] (subtractive decode)
[    0.157563] pci_bus 0000:03: busn_res: can not insert [bus 03-ff] under [bus 02-03] (conflicts with (null) [bus 02-03])
[    0.157573] pci_bus 0000:03: busn_res: [bus 03-ff] end is updated to 06
[    0.157581] pci_bus 0000:03: busn_res: can not insert [bus 03-06] under [bus 02-03] (conflicts with (null) [bus 02-03])
[    0.157590] pci_bus 0000:03: [bus 03-06] partially hidden behind transparent bridge 0000:02 [bus 02-03]
[    0.157596] pci 0000:00:1e.0: bridge has subordinate 03 but max busn 06
[    0.157613] pci_bus 0000:00: on NUMA node 0
[    0.159472] ACPI: PCI Interrupt Link [C0C0] (IRQs 5 10 *11)
[    0.159718] ACPI: PCI Interrupt Link [C0C1] (IRQs *5 10 11)
[    0.159944] ACPI: PCI Interrupt Link [C0C2] (IRQs 5 10 11) *0, disabled.
[    0.160216] ACPI: PCI Interrupt Link [C0C3] (IRQs 5 10 *11)
[    0.160458] ACPI: PCI Interrupt Link [C0C4] (IRQs 5 *10 11)
[    0.160685] ACPI: PCI Interrupt Link [C0C5] (IRQs) *0, disabled.
[    0.160911] ACPI: PCI Interrupt Link [C0C6] (IRQs) *0, disabled.
[    0.161134] ACPI: PCI Interrupt Link [C0C7] (IRQs) *0, disabled.
[    0.162750] ACPI: Enabled 6 GPEs in block 10 to 1F
[    0.162850] ACPI : EC: GPE = 0x1d, I/O: command/status = 0x66, data = 0x62
[    0.163210] vgaarb: setting as boot device: PCI:0000:01:00.0
[    0.163216] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.163223] vgaarb: loaded
[    0.163227] vgaarb: bridge control possible 0000:01:00.0
[    0.164118] SCSI subsystem initialized
[    0.164255] libata version 3.00 loaded.
[    0.164334] ACPI: bus type USB registered
[    0.164402] usbcore: registered new interface driver usbfs
[    0.164434] usbcore: registered new interface driver hub
[    0.164470] usbcore: registered new device driver usb
[    0.164921] PCI: Using ACPI for IRQ routing
[    0.164932] PCI: pci_cache_line_size set to 64 bytes
[    0.164996] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
[    0.165002] e820: reserve RAM buffer [mem 0x2ffd0000-0x2fffffff]
[    0.165339] NetLabel: Initializing
[    0.165343] NetLabel:  domain hash size = 128
[    0.165346] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.165377] NetLabel:  unlabeled traffic allowed by default
[    0.165719] clocksource: Switched to clocksource pit
[    0.187219] AppArmor: AppArmor Filesystem Enabled
[    0.187453] pnp: PnP ACPI init
[    0.187849] system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved
[    0.187859] system 00:00: [mem 0x000e0000-0x000fffff] could not be reserved
[    0.187866] system 00:00: [mem 0x00100000-0x2fffffff] could not be reserved
[    0.187877] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.189438] pnp 00:01: [dma 2]
[    0.189539] pnp 00:01: Plug and Play ACPI device, IDs PNP0700 (active)
[    0.189899] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.189997] pnp 00:03: Plug and Play ACPI device, IDs PNP0303 (active)
[    0.190091] pnp 00:04: Plug and Play ACPI device, IDs SYN0100 SYN0002 PNP0f13 (active)
[    0.190362] system 00:05: [mem 0xffb00000-0xffbfffff] has been reserved
[    0.190370] system 00:05: [mem 0xfff00000-0xffffffff] has been reserved
[    0.190379] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.191082] system 00:06: [io  0x04d0-0x04d1] has been reserved
[    0.191095] system 00:06: [io  0x1000-0x107f] could not be reserved
[    0.191101] system 00:06: [io  0x1100-0x113f] has been reserved
[    0.191107] system 00:06: [io  0x1200-0x121f] has been reserved
[    0.191113] system 00:06: [mem 0xffc00000-0xffc003ff] has been reserved
[    0.191121] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.191518] pnp: PnP ACPI: found 7 devices
[    0.191533] PnPBIOS: Disabled by ACPI PNP
[    0.231139] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    0.231178] clocksource: Switched to clocksource acpi_pm
[    0.231230] pci 0000:02:06.0: res[15]=[mem 0x04000000-0x03ffffff pref] res_to_dev_res add_size 4000000 min_align 4000000
[    0.231237] pci 0000:02:06.0: res[15]=[mem 0x04000000-0x03ffffff pref] res_to_dev_res add_size 4000000 min_align 4000000
[    0.231248] pci 0000:00:1e.0: bridge window [mem 0x04000000-0x03ffffff pref] to [bus 02-03] add_size 4000000 add_align 4000000
[    0.231259] pci 0000:00:1f.0: BAR 13: [io  size 0x0080] has bogus alignment
[    0.231267] pci 0000:00:1e.0: res[15]=[mem 0x04000000-0x03ffffff pref] res_to_dev_res add_size 4000000 min_align 4000000
[    0.231274] pci 0000:00:1e.0: res[15]=[mem 0x04000000-0x07ffffff pref] res_to_dev_res add_size 4000000 min_align 4000000
[    0.231292] pci 0000:00:1e.0: BAR 15: assigned [mem 0x30000000-0x33ffffff pref]
[    0.231299] pci 0000:00:1f.1: BAR 5: assigned [mem 0x34000000-0x340003ff]
[    0.231314] pci 0000:01:00.0: BAR 6: assigned [mem 0x40320000-0x4033ffff pref]
[    0.231320] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.231326] pci 0000:00:01.0:   bridge window [io  0x3000-0x3fff]
[    0.231334] pci 0000:00:01.0:   bridge window [mem 0x40300000-0x403fffff]
[    0.231341] pci 0000:00:01.0:   bridge window [mem 0x48000000-0x4fffffff pref]
[    0.231355] pci 0000:02:06.0: res[15]=[mem 0x04000000-0x03ffffff pref] res_to_dev_res add_size 4000000 min_align 4000000
[    0.231363] pci 0000:02:06.0: res[15]=[mem 0x04000000-0x07ffffff pref] res_to_dev_res add_size 4000000 min_align 4000000
[    0.231369] pci 0000:02:06.0: res[16]=[mem 0x04000000-0x03ffffff] res_to_dev_res add_size 4000000 min_align 4000000
[    0.231375] pci 0000:02:06.0: res[16]=[mem 0x04000000-0x07ffffff] res_to_dev_res add_size 4000000 min_align 4000000
[    0.231381] pci 0000:02:06.0: res[13]=[io  0x0100-0x00ff] res_to_dev_res add_size 100 min_align 100
[    0.231387] pci 0000:02:06.0: res[13]=[io  0x0100-0x01ff] res_to_dev_res add_size 100 min_align 100
[    0.231392] pci 0000:02:06.0: res[14]=[io  0x0100-0x00ff] res_to_dev_res add_size 100 min_align 100
[    0.231397] pci 0000:02:06.0: res[14]=[io  0x0100-0x01ff] res_to_dev_res add_size 100 min_align 100
[    0.231404] pci 0000:02:06.0: BAR 15: assigned [mem 0x30000000-0x33ffffff pref]
[    0.231413] pci 0000:02:06.0: BAR 16: assigned [mem 0x38000000-0x3bffffff]
[    0.231419] pci 0000:02:06.0: BAR 13: assigned [io  0x2400-0x24ff]
[    0.231425] pci 0000:02:06.0: BAR 14: assigned [io  0x2800-0x28ff]
[    0.231431] pci 0000:02:06.0: CardBus bridge to [bus 03-06]
[    0.231436] pci 0000:02:06.0:   bridge window [io  0x2400-0x24ff]
[    0.231443] pci 0000:02:06.0:   bridge window [io  0x2800-0x28ff]
[    0.231451] pci 0000:02:06.0:   bridge window [mem 0x30000000-0x33ffffff pref]
[    0.231459] pci 0000:02:06.0:   bridge window [mem 0x38000000-0x3bffffff]
[    0.231466] pci 0000:00:1e.0: PCI bridge to [bus 02-03]
[    0.231472] pci 0000:00:1e.0:   bridge window [io  0x2000-0x2fff]
[    0.231481] pci 0000:00:1e.0:   bridge window [mem 0x40000000-0x402fffff]
[    0.231489] pci 0000:00:1e.0:   bridge window [mem 0x30000000-0x33ffffff pref]
[    0.231501] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7 window]
[    0.231507] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff window]
[    0.231512] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[    0.231517] pci_bus 0000:00: resource 7 [mem 0x30000000-0xffffffff window]
[    0.231522] pci_bus 0000:00: resource 8 [mem 0x000d0000-0x000dffff window]
[    0.231527] pci_bus 0000:01: resource 0 [io  0x3000-0x3fff]
[    0.231532] pci_bus 0000:01: resource 1 [mem 0x40300000-0x403fffff]
[    0.231537] pci_bus 0000:01: resource 2 [mem 0x48000000-0x4fffffff pref]
[    0.231542] pci_bus 0000:02: resource 0 [io  0x2000-0x2fff]
[    0.231547] pci_bus 0000:02: resource 1 [mem 0x40000000-0x402fffff]
[    0.231552] pci_bus 0000:02: resource 2 [mem 0x30000000-0x33ffffff pref]
[    0.231557] pci_bus 0000:02: resource 4 [io  0x0000-0x0cf7 window]
[    0.231562] pci_bus 0000:02: resource 5 [io  0x0d00-0xffff window]
[    0.231567] pci_bus 0000:02: resource 6 [mem 0x000a0000-0x000bffff window]
[    0.231572] pci_bus 0000:02: resource 7 [mem 0x30000000-0xffffffff window]
[    0.231577] pci_bus 0000:02: resource 8 [mem 0x000d0000-0x000dffff window]
[    0.231582] pci_bus 0000:03: resource 0 [io  0x2400-0x24ff]
[    0.231587] pci_bus 0000:03: resource 1 [io  0x2800-0x28ff]
[    0.231592] pci_bus 0000:03: resource 2 [mem 0x30000000-0x33ffffff pref]
[    0.231597] pci_bus 0000:03: resource 3 [mem 0x38000000-0x3bffffff]
[    0.231685] NET: Registered protocol family 2
[    0.232136] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.232172] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.232242] TCP: Hash tables configured (established 8192 bind 8192)
[    0.232331] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.232351] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.232476] NET: Registered protocol family 1
[    0.232541] pci 0000:01:00.0: Video device with shadowed ROM
[    0.232585] pci 0000:02:08.0: Firmware left e100 interrupts enabled; disabling
[    0.232999] ACPI: PCI Interrupt Link [C0C4] enabled at IRQ 10
[    0.233005] PCI: setting IRQ 10 as level-triggered
[    0.233259] PCI: CLS 32 bytes, default 64
[    0.233434] Trying to unpack rootfs image as initramfs...
[    1.567806] Freeing initrd memory: 31984K (ed058000 - eef94000)
[    1.568386] microcode: CPU0 sig=0xf24, pf=0x8, revision=0xd
[    1.568546] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    1.568801] Scanning for low memory corruption every 60 seconds
[    1.569527] futex hash table entries: 256 (order: 2, 16384 bytes)
[    1.569571] Initialise system trusted keyring
[    1.569632] audit: initializing netlink subsys (disabled)
[    1.569688] audit: type=2000 audit(1444196038.567:1): initialized
[    1.570337] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    1.575324] zpool: loaded
[    1.575332] zbud: loaded
[    1.575545] VFS: Disk quotas dquot_6.6.0
[    1.575657] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.577059] fuse init (API version 7.23)
[    1.577507] Key type big_key registered
[    1.578130] Key type asymmetric registered
[    1.578138] Asymmetric key parser 'x509' registered
[    1.578179] bounce: pool size: 64 pages
[    1.578300] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    1.578384] io scheduler noop registered
[    1.578391] io scheduler deadline registered (default)
[    1.578488] io scheduler cfq registered
[    1.578851] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    1.578872] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    1.578960] vesafb: mode is 1400x1050x32, linelength=5600, pages=0
[    1.578963] vesafb: scrolling: redraw
[    1.578969] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
[    1.579016] vesafb: framebuffer at 0x48000000, mapped to 0xf0800000, using 5760k, total 5760k
[    1.579329] Console: switching to colour frame buffer device 175x65
[    1.579382] fb0: VESA VGA frame buffer device
[    1.579762] ACPI: AC Adapter [C130] (on-line)
[    1.579944] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[    1.579956] ACPI: Power Button [C190]
[    1.580167] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1
[    1.580175] ACPI: Sleep Button [C134]
[    1.580307] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input2
[    1.580382] ACPI: Lid Switch [C133]
[    1.580500] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[    1.580508] ACPI: Power Button [PWRF]
[    1.612307] tsc: Marking TSC unstable due to TSC halts in idle
[    1.612323] ACPI: acpi_idle registered with cpuidle
[    1.648753] thermal LNXTHERM:00: registered as thermal_zone0
[    1.648759] ACPI: Thermal Zone [TZ1] (31 C)
[    1.662255] thermal LNXTHERM:01: registered as thermal_zone1
[    1.662260] ACPI: Thermal Zone [TZ2] (22 C)
[    1.664857] thermal LNXTHERM:02: registered as thermal_zone2
[    1.664862] ACPI: Thermal Zone [TZ3] (16 C)
[    1.665099] ACPI: Battery Slot [C132] (battery absent)
[    1.665294] ACPI: Battery Slot [C131] (battery absent)
[    1.665399] GHES: HEST is not enabled!
[    1.665463] isapnp: Scanning for PnP cards...
[    1.714889] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[    1.719363] Linux agpgart interface v0.103
[    1.719515] agpgart-intel 0000:00:00.0: Intel i845 Chipset
[    1.734656] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0x60000000
[    1.741222] brd: module loaded
[    1.744514] loop: module loaded
[    1.745022] ata_piix 0000:00:1f.1: version 2.13
[    1.745044] ata_piix 0000:00:1f.1: enabling device (0005 -> 0007)
[    1.745414] ACPI: PCI Interrupt Link [C0C2] enabled at IRQ 11
[    1.745419] PCI: setting IRQ 11 as level-triggered
[    1.747309] scsi host0: ata_piix
[    1.747543] scsi host1: ata_piix
[    1.747671] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x4440 irq 14
[    1.747677] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x4448 irq 15
[    1.747945] libphy: Fixed MDIO Bus: probed
[    1.747953] tun: Universal TUN/TAP device driver, 1.6
[    1.747956] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    1.748240] PPP generic driver version 2.4.2
[    1.748471] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.748485] ehci-pci: EHCI PCI platform driver
[    1.748643] ehci-pci 0000:02:0e.2: EHCI Host Controller
[    1.748659] ehci-pci 0000:02:0e.2: new USB bus registered, assigned bus number 1
[    1.748740] ehci-pci 0000:02:0e.2: irq 10, io mem 0x40280000
[    1.792730] ehci-pci 0000:02:0e.2: USB 2.0 started, EHCI 0.95
[    1.792877] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.792883] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.792887] usb usb1: Product: EHCI Host Controller
[    1.792892] usb usb1: Manufacturer: Linux 4.2.0-12-generic ehci_hcd
[    1.792896] usb usb1: SerialNumber: 0000:02:0e.2
[    1.793263] hub 1-0:1.0: USB hub found
[    1.793284] hub 1-0:1.0: 5 ports detected
[    1.793880] ehci-platform: EHCI generic platform driver
[    1.793925] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.793941] ohci-pci: OHCI PCI platform driver
[    1.794076] ohci-pci 0000:02:0e.0: OHCI PCI host controller
[    1.794090] ohci-pci 0000:02:0e.0: new USB bus registered, assigned bus number 2
[    1.794130] ohci-pci 0000:02:0e.0: irq 10, io mem 0x40180000
[    2.432481] ata2.00: ATAPI: DW-224E, A.0F, max MWDMA2
[    2.432850] ata1.00: ATA-6: FUJITSU MHR2040AT, 53BB, max UDMA/100
[    2.432856] ata1.00: 78140160 sectors, multi 16: LBA48 
[    2.476849] ata2.00: configured for MWDMA2
[    2.520589] isapnp: No Plug & Play device found
[    2.520957] ata1.00: configured for UDMA/100
[    2.521180] scsi 0:0:0:0: Direct-Access     ATA      FUJITSU MHR2040A 53BB PQ: 0 ANSI: 5
[    2.521758] sd 0:0:0:0: [sda] 78140160 512-byte logical blocks: (40.0 GB/37.2 GiB)
[    2.521875] sd 0:0:0:0: [sda] Write Protect is off
[    2.521882] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.521935] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.522532] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    2.522836] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    2.522843] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.522849] usb usb2: Product: OHCI PCI host controller
[    2.522854] usb usb2: Manufacturer: Linux 4.2.0-12-generic ohci_hcd
[    2.522858] usb usb2: SerialNumber: 0000:02:0e.0
[    2.523428] hub 2-0:1.0: USB hub found
[    2.523450] hub 2-0:1.0: 3 ports detected
[    2.523767] scsi 1:0:0:0: CD-ROM            TEAC     DW-224E          A.0F PQ: 0 ANSI: 5
[    2.524192] ohci-pci 0000:02:0e.1: OHCI PCI host controller
[    2.524208] ohci-pci 0000:02:0e.1: new USB bus registered, assigned bus number 3
[    2.524271] ohci-pci 0000:02:0e.1: irq 10, io mem 0x40200000
[    2.537086] sr 1:0:0:0: [sr0] scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[    2.537094] cdrom: Uniform CD-ROM driver Revision: 3.20
[    2.537419] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    2.537672] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    2.546744]  sda: sda1 sda2 < sda5 sda6 >
[    2.547624] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.568055] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x369a7088a47, max_idle_ns: 881590662161 ns
[    3.086455] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    3.086462] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.086466] usb usb3: Product: OHCI PCI host controller
[    3.086471] usb usb3: Manufacturer: Linux 4.2.0-12-generic ohci_hcd
[    3.086475] usb usb3: SerialNumber: 0000:02:0e.1
[    3.086858] hub 3-0:1.0: USB hub found
[    3.086878] hub 3-0:1.0: 2 ports detected
[    3.087200] ohci-platform: OHCI generic platform driver
[    3.087251] uhci_hcd: USB Universal Host Controller Interface driver
[    3.087432] i8042: PNP: PS/2 Controller [PNP0303:C177,PNP0f13:C178] at 0x60,0x64 irq 1,12
[    3.089760] i8042: Detected active multiplexing controller, rev 1.1
[    3.091067] serio: i8042 KBD port at 0x60,0x64 irq 1
[    3.091080] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[    3.091193] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[    3.091287] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[    3.091376] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[    3.091763] mousedev: PS/2 mouse device common for all mice
[    3.092306] rtc_cmos 00:02: RTC can wake from S4
[    3.092510] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[    3.092540] rtc_cmos 00:02: alarms up to one month, y3k, 114 bytes nvram
[    3.092567] i2c /dev entries driver
[    3.092759] device-mapper: uevent: version 1.0.3
[    3.092967] device-mapper: ioctl: 4.33.0-ioctl (2015-8-18) initialised: dm-devel@redhat.com
[    3.093044] platform eisa.0: Probing EISA bus 0
[    3.093051] platform eisa.0: EISA: Cannot allocate resource for mainboard
[    3.093057] platform eisa.0: Cannot allocate resource for EISA slot 1
[    3.093061] platform eisa.0: Cannot allocate resource for EISA slot 2
[    3.093066] platform eisa.0: Cannot allocate resource for EISA slot 3
[    3.093070] platform eisa.0: Cannot allocate resource for EISA slot 4
[    3.093075] platform eisa.0: Cannot allocate resource for EISA slot 5
[    3.093079] platform eisa.0: Cannot allocate resource for EISA slot 6
[    3.093084] platform eisa.0: Cannot allocate resource for EISA slot 7
[    3.093088] platform eisa.0: Cannot allocate resource for EISA slot 8
[    3.093093] platform eisa.0: EISA: Detected 0 cards
[    3.093314] cpufreq-nforce2: No nForce2 chipset.
[    3.093329] ledtrig-cpu: registered to indicate activity on CPUs
[    3.093353] PCCT header not found.
[    3.093957] NET: Registered protocol family 10
[    3.094573] NET: Registered protocol family 17
[    3.094605] Key type dns_resolver registered
[    3.095033] Using IPI No-Shortcut mode
[    3.095370] Loading compiled-in X.509 certificates
[    3.104175] Loaded X.509 cert 'Build time autogenerated kernel key: ac0e10cb631bbf08b6f27ec68d5eece5618bbca7'
[    3.104218] registered taskstats version 1
[    3.104269] zswap: loading zswap
[    3.104275] zswap: using zbud pool
[    3.104293] zswap: using lzo compressor
[    3.110299] Key type trusted registered
[    3.120560] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[    3.122827] Key type encrypted registered
[    3.122855] AppArmor: AppArmor sha1 policy hashing enabled
[    3.122867] ima: No TPM chip found, activating TPM-bypass!
[    3.122931] evm: HMAC attrs: 0x1
[    3.123416]   Magic number: 3:108:567
[    3.123434] misc network_latency: hash matches
[    3.123646] rtc_cmos 00:02: setting system clock to 2015-10-07 05:34:01 UTC (1444196041)
[    3.123802] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    3.123806] EDD information not available.
[    3.123947] PM: Hibernation image not present or could not be loaded.
[    3.125672] Freeing unused kernel memory: 920K (c1ae8000 - c1bce000)
[    3.125825] Write protecting the kernel text: 7396k
[    3.125903] Write protecting the kernel read-only data: 3024k
[    3.167594] random: udevadm urandom read with 23 bits of entropy available
[    3.350670] ACPI: Video Device [C0CE] (multi-head: yes  rom: no  post: no)
[    3.351029] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/device:00/LNXVIDEO:00/input/input9
[    3.495669] wmi: Mapper loaded
[    3.499264] Floppy drive(s): fd0 is 1.44M
[    3.519622] FDC 0 is a National Semiconductor PC87306
[    3.581727] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
[    3.581735] e100: Copyright(c) 1999-2006 Intel Corporation
[    3.604980] e100 0000:02:08.0 0000:02:08.0 (uninitialized): EEPROM corrupted
[    3.788221] e100: probe of 0000:02:08.0 failed with error -11
[    3.881528] [drm] Initialized drm 1.1.0 20060810
[    4.331100] [drm] radeon kernel modesetting enabled.
[    4.331225] checking generic (48000000 5a0000) vs hw (48000000 8000000)
[    4.331231] fb: switching to radeondrmfb from VESA VGA
[    4.331317] Console: switching to colour dummy device 80x25
[    4.333269] ACPI: PCI Interrupt Link [C0C0] enabled at IRQ 11
[    4.334616] [drm] initializing kernel modesetting (RV200 0x1002:0x4C57 0x0E11:0x004A).
[    4.334647] [drm] register mmio base: 0x40300000
[    4.334651] [drm] register mmio size: 65536
[    4.334850] agpgart-intel 0000:00:00.0: AGP 2.0 bridge
[    4.334868] agpgart-intel 0000:00:00.0: putting AGP V2 device into 4x mode
[    4.334887] radeon 0000:01:00.0: putting AGP V2 device into 4x mode
[    4.334921] radeon 0000:01:00.0: GTT: 256M 0x60000000 - 0x6FFFFFFF
[    4.334933] radeon 0000:01:00.0: VRAM: 128M 0x0000000048000000 - 0x000000004FFFFFFF (64M used)
[    4.334951] [drm] Detected VRAM RAM=128M, BAR=128M
[    4.334955] [drm] RAM width 128bits DDR
[    4.335117] [TTM] Zone  kernel: Available graphics memory: 381256 kiB
[    4.335121] [TTM] Initializing pool allocator
[    4.335138] [TTM] Initializing DMA pool allocator
[    4.335198] [drm] radeon: 64M of VRAM memory ready
[    4.335203] [drm] radeon: 256M of GTT memory ready.
[    4.337326] radeon 0000:01:00.0: WB disabled
[    4.337341] radeon 0000:01:00.0: fence driver on ring 0 use gpu addr 0x0000000060000000 and cpu addr 0xf07f6000
[    4.337348] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    4.337352] [drm] Driver supports precise vblank timestamp query.
[    4.337377] [drm] radeon: irq initialized.
[    4.337406] [drm] Loading R100 Microcode
[    4.337782] [drm] radeon: ring at 0x0000000060001000
[    4.337813] [drm] ring test succeeded in 1 usecs
[    4.338089] [drm] ib test succeeded in 0 usecs
[    4.342963] [drm] Panel ID String: LGP                     
[    4.342972] [drm] Panel Size 1400x1050
[    4.343502] [drm] No TV DAC info found in BIOS
[    4.344130] [drm] Radeon Display Connectors
[    4.344136] [drm] Connector 0:
[    4.344139] [drm]   VGA-1
[    4.344145] [drm]   DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60
[    4.344148] [drm]   Encoders:
[    4.344151] [drm]     CRT1: INTERNAL_DAC1
[    4.344154] [drm] Connector 1:
[    4.344157] [drm]   DVI-D-1
[    4.344159] [drm]   HPD1
[    4.344163] [drm]   DDC: 0x64 0x64 0x64 0x64 0x64 0x64 0x64 0x64
[    4.344166] [drm]   Encoders:
[    4.344168] [drm]     DFP1: INTERNAL_TMDS1
[    4.344171] [drm] Connector 2:
[    4.344174] [drm]   LVDS-1
[    4.344178] [drm]   DDC: 0x6c 0x6c 0x6c 0x6c 0x6c 0x6c 0x6c 0x6c
[    4.344180] [drm]   Encoders:
[    4.344183] [drm]     LCD1: INTERNAL_LVDS
[    4.344185] [drm] Connector 3:
[    4.344188] [drm]   SVIDEO-1
[    4.344190] [drm]   Encoders:
[    4.344192] [drm]     TV1: INTERNAL_DAC2
[    4.470837] [drm] fb mappable at 0x48040000
[    4.470847] [drm] vram apper at 0x48000000
[    4.470850] [drm] size 5914624
[    4.470853] [drm] fb depth is 24
[    4.470856] [drm]    pitch is 5632
[    4.471503] fbcon: radeondrmfb (fb0) is primary device
[    4.473164] Console: switching to colour frame buffer device 175x65
[    4.473232] radeon 0000:01:00.0: fb0: radeondrmfb frame buffer device
[    4.473236] radeon 0000:01:00.0: registered panic notifier
[    4.473254] [drm] Initialized radeon 2.43.0 20080528 for 0000:01:00.0 on minor 0
[    4.686318] psmouse serio4: synaptics: Touchpad model: 1, fw: 5.9, id: 0x336ab1, caps: 0x984713/0x4000/0x0/0x0, board id: 0, fw id: 753378
[    4.729107] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input13
[    5.115550] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[    5.127200] random: nonblocking pool is initialized
[    6.641042] systemd[1]: Failed to insert module 'kdbus': Function not implemented
[    6.839098] systemd[1]: systemd 225 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID -ELFUTILS +KMOD -IDN)
[    6.839476] systemd[1]: Detected architecture x86.
[    6.857550] systemd[1]: Set hostname to <Presario-2800>.
[    9.524143] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    9.524278] systemd[1]: Reached target User and Group Name Lookups.
[    9.524401] systemd[1]: Created slice Root Slice.
[    9.524528] systemd[1]: Listening on udev Kernel Socket.
[    9.524663] systemd[1]: Listening on udev Control Socket.
[    9.524839] systemd[1]: Listening on Journal Socket.
[    9.525174] systemd[1]: Listening on Journal Audit Socket.
[    9.525636] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    9.525965] systemd[1]: Created slice User and Session Slice.
[    9.526024] systemd[1]: Reached target Remote File Systems (Pre).
[    9.526147] systemd[1]: Listening on fsck to fsckd communication Socket.
[    9.526285] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[    9.526602] systemd[1]: Created slice System Slice.
[    9.528478] systemd[1]: Mounting POSIX Message Queue File System...
[    9.528580] systemd[1]: Reached target Slices.
[    9.530585] systemd[1]: Starting Uncomplicated firewall...
[    9.537538] systemd[1]: Starting Increase datagram queue length...
[    9.539820] systemd[1]: Mounting Huge Pages File System...
[    9.546689] systemd[1]: Started Read required files in advance.
[    9.699046] systemd[1]: Starting Load Kernel Modules...
[    9.701491] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[    9.703541] systemd[1]: Starting Setup Virtual Console...
[    9.982144] systemd[1]: Starting udev Coldplug all Devices...
[    9.984267] systemd[1]: Mounting Debug File System...
[    9.984790] systemd[1]: Created slice system-getty.slice.
[    9.985018] systemd[1]: Listening on Journal Socket (/dev/log).
[    9.985106] systemd[1]: Reached target Encrypted Volumes.
[    9.995724] systemd[1]: Started Setup Virtual Console.
[   10.130352] systemd[1]: Started Create list of required static device nodes for the current kernel.
[   10.132901] systemd[1]: Starting Create Static Device Nodes in /dev...
[   10.295395] systemd[1]: Started Uncomplicated firewall.
[   10.638455] systemd[1]: Mounted Huge Pages File System.
[   10.638578] systemd[1]: Mounted POSIX Message Queue File System.
[   10.638638] systemd[1]: Mounted Debug File System.
[   10.639620] systemd[1]: Started Increase datagram queue length.
[   10.706446] systemd[1]: Listening on Syslog Socket.
[   10.711433] systemd[1]: Starting Journal Service...
[   10.918047] systemd[1]: Started udev Coldplug all Devices.
[   10.993964] lp: driver loaded but no devices found
[   11.102551] ppdev: user-space parallel port driver
[   11.237654] systemd[1]: Started Load Kernel Modules.
[   11.239763] systemd[1]: Mounting FUSE Control File System...
[   11.242404] systemd[1]: Starting Apply Kernel Variables...
[   11.258331] systemd[1]: Mounted FUSE Control File System.
[   11.671563] systemd[1]: Started Journal Service.
[   13.588188] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[   14.621798] systemd-journald[194]: Received request to flush runtime journal from PID 1
[   15.675253] intel_rng: FWH not detected
[   15.755355] NET: Registered protocol family 23
[   15.938346] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   16.062096] nsc-ircc, Found chip at base=0x02e
[   16.062108] nsc-ircc, Wrong chip version ff
[   17.130596] ACPI: PCI Interrupt Link [C0C3] enabled at IRQ 11
[   17.130647] yenta_cardbus 0000:02:06.0: CardBus bridge found [0e11:004a]
[   17.130673] yenta_cardbus 0000:02:06.0: Enabling burst memory read transactions
[   17.130681] yenta_cardbus 0000:02:06.0: Using CSCINT to route CSC interrupts to PCI
[   17.130685] yenta_cardbus 0000:02:06.0: Routing CardBus interrupts to PCI
[   17.130693] yenta_cardbus 0000:02:06.0: TI: mfunc 0x012c1202, devctl 0x64
[   17.362327] yenta_cardbus 0000:02:06.0: ISA IRQ mask 0x00b8, PCI irq 11
[   17.362336] yenta_cardbus 0000:02:06.0: Socket status: 30000006
[   17.362345] pci_bus 0000:02: Raising subordinate bus# of parent bus (#02) from #03 to #06
[   17.362360] yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge window: [io  0x2000-0x2fff]
[   17.362368] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x2000-0x2fff:
[   17.363893]  excluding 0x2000-0x2047 0x2400-0x24ff 0x2800-0x28ff
[   17.382564] yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge window: [mem 0x40000000-0x402fffff]
[   17.382577] pcmcia_socket pcmcia_socket0: cs: memory probe 0x40000000-0x402fffff:
[   17.382583]  excluding 0x40000000-0x4002ffff 0x40060000-0x4008ffff 0x400f0000-0x4011ffff 0x40180000-0x401affff 0x401e0000-0x4020ffff 0x40270000-0x4029ffff
[   17.382620] yenta_cardbus 0000:02:06.0: pcmcia: parent PCI bridge window: [mem 0x30000000-0x33ffffff pref]
[   17.382627] pcmcia_socket pcmcia_socket0: cs: memory probe 0x30000000-0x33ffffff:
[   17.382644]  excluding 0x30000000-0x33ffffff
[   18.214143] ACPI: PCI Interrupt Link [C0C1] enabled at IRQ 5
[   18.214154] PCI: setting IRQ 5 as level-triggered
[   18.884112] snd_intel8x0 0000:00:1f.5: intel8x0_measure_ac97_clock: measured 54721 usecs (2630 samples)
[   18.884124] snd_intel8x0 0000:00:1f.5: clocking to 48000
[   22.297111] Adding 999420k swap on /dev/sda5.  Priority:-1 extents:1 across:999420k FS
[   22.521261] audit: type=1400 audit(1444196060.895:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/lightdm/lightdm-guest-session" pid=430 comm="apparmor_parser"
[   22.521285] audit: type=1400 audit(1444196060.895:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="chromium" pid=430 comm="apparmor_parser"
[   22.739632] audit: type=1400 audit(1444196061.111:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/sbin/dhclient" pid=430 comm="apparmor_parser"
[   22.739662] audit: type=1400 audit(1444196061.111:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=430 comm="apparmor_parser"
[   22.739679] audit: type=1400 audit(1444196061.111:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=430 comm="apparmor_parser"
[   22.739695] audit: type=1400 audit(1444196061.111:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=430 comm="apparmor_parser"
[   24.645607] audit: type=1400 audit(1444196063.019:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/evince" pid=430 comm="apparmor_parser"
[   24.645639] audit: type=1400 audit(1444196063.019:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="sanitized_helper" pid=430 comm="apparmor_parser"
[   24.645655] audit: type=1400 audit(1444196063.019:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/evince-previewer" pid=430 comm="apparmor_parser"
[   24.645671] audit: type=1400 audit(1444196063.019:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="sanitized_helper" pid=430 comm="apparmor_parser"

lsmode

odule                  Size  Used by
binfmt_misc            20480  1
snd_intel8x0           36864  1
snd_ac97_codec        106496  1 snd_intel8x0
ac97_bus               16384  1 snd_ac97_codec
snd_pcm                90112  2 snd_ac97_codec,snd_intel8x0
pcmcia                 57344  0
snd_seq_midi           16384  0
snd_seq_midi_event     16384  1 snd_seq_midi
snd_rawmidi            28672  1 snd_seq_midi
yenta_socket           45056  0
snd_seq                57344  2 snd_seq_midi_event,snd_seq_midi
pcmcia_rsrc            20480  1 yenta_socket
pcmcia_core            24576  3 pcmcia,pcmcia_rsrc,yenta_socket
snd_seq_device         16384  3 snd_seq,snd_rawmidi,snd_seq_midi
snd_timer              28672  2 snd_pcm,snd_seq
snd                    69632  9 snd_ac97_codec,snd_intel8x0,snd_timer,snd_pcm,snd_seq,snd_rawmidi,snd_seq_device
joydev                 20480  0
input_leds             16384  0
soundcore              16384  1 snd
serio_raw              16384  0
shpchp                 32768  0
lpc_ich                20480  0
irda                  172032  0
8250_fintek            16384  0
crc_ccitt              16384  1 irda
mac_hid                16384  0
parport_pc             32768  0
ppdev                  20480  0
lp                     20480  0
parport                45056  3 lp,ppdev,parport_pc
autofs4                40960  2
radeon               1454080  2
i2c_algo_bit           16384  1 radeon
ttm                    86016  1 radeon
drm_kms_helper        114688  1 radeon
drm                   303104  5 ttm,drm_kms_helper,radeon
psmouse               114688  0
e100                   36864  0
pata_acpi              16384  0
mii                    16384  1 e100
floppy                 61440  0
wmi                    20480  0
video                  24576  0

sudo lspci -vv

00:00.0 Host bridge: Intel Corporation 82845 845 [Brookdale] Chipset Host Bridge (rev 04)
	Subsystem: Compaq Computer Corporation Device 004a
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 0
	Region 0: Memory at 60000000 (32-bit, prefetchable) [size=256M]
	Capabilities: [e4] Vendor Specific Information: Len=04 <?>
	Capabilities: [a0] AGP version 2.0
		Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
		Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4
	Kernel driver in use: agpgart-intel

00:01.0 PCI bridge: Intel Corporation 82845 845 [Brookdale] Chipset AGP Bridge (rev 04) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	I/O behind bridge: 00003000-00003fff
	Memory behind bridge: 40300000-403fffff
	Prefetchable memory behind bridge: 48000000-4fffffff
	Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 42) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Bus: primary=00, secondary=02, subordinate=06, sec-latency=32
	I/O behind bridge: 00002000-00002fff
	Memory behind bridge: 40000000-402fffff
	Prefetchable memory behind bridge: 30000000-33ffffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

00:1f.0 ISA bridge: Intel Corporation 82801CAM ISA Bridge (LPC) (rev 02)
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Kernel driver in use: lpc_ich

00:1f.1 IDE interface: Intel Corporation 82801CAM IDE U100 Controller (rev 02) (prog-if 8a [Master SecP PriP])
	Subsystem: Compaq Computer Corporation Device 004a
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 11
	Region 0: I/O ports at 01f0 [size=8]
	Region 1: I/O ports at 03f4
	Region 2: I/O ports at 0170 [size=8]
	Region 3: I/O ports at 0374
	Region 4: I/O ports at 4440 [size=16]
	Region 5: Memory at 34000000 (32-bit, non-prefetchable) [size=1K]
	Kernel driver in use: ata_piix

00:1f.5 Multimedia audio controller: Intel Corporation 82801CA/CAM AC'97 Audio Controller (rev 02)
	Subsystem: Compaq Computer Corporation Device 004a
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 5
	Region 0: I/O ports at 4000 [size=256]
	Region 1: I/O ports at 4400 [size=64]
	Kernel driver in use: snd_intel8x0

01:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] RV200/M7 [Mobility Radeon 7500] (prog-if 00 [VGA controller])
	Subsystem: Compaq Computer Corporation Device 004a
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 66 (2000ns min), Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at 48000000 (32-bit, prefetchable) [size=128M]
	Region 1: I/O ports at 3000 [size=256]
	Region 2: Memory at 40300000 (32-bit, non-prefetchable) [size=64K]
	[virtual] Expansion ROM at 40320000 [disabled] [size=128K]
	Capabilities: [58] AGP version 2.0
		Status: RQ=48 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
		Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: radeon

02:04.0 Communication controller: Conexant Systems, Inc. HSF 56k HSFi Modem (rev 01)
	Subsystem: Compaq Computer Corporation Device 8d89
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64
	Interrupt: pin A routed to IRQ 5
	Region 0: Memory at 40000000 (32-bit, non-prefetchable) [size=64K]
	Region 1: I/O ports at 2040 [size=8]
	Capabilities: [40] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

02:06.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (rev 02)
	Subsystem: Compaq Computer Corporation Device 004a
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 168, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at 40080000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
	Memory window 0: 30000000-33ffffff (prefetchable)
	Memory window 1: 38000000-3bffffff
	I/O window 0: 00002400-000024ff
	I/O window 1: 00002800-000028ff
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
	16-bit legacy interface ports at 0001
	Capabilities: [a0] Power Management version 1
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
		Bridge: PM- B3+
	Kernel driver in use: yenta_cardbus

02:08.0 Ethernet controller: Intel Corporation 82801CAM (ICH3) PRO/100 VE (LOM) Ethernet Controller (rev 42)
	Subsystem: Compaq Computer Corporation Device 0093
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin A routed to IRQ 10
	Region 0: Memory at 40100000 (32-bit, non-prefetchable) [size=4K]
	Region 1: I/O ports at 2000 [size=64]
	Capabilities: [dc] Power Management version 2
		Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-

02:0e.0 USB controller: NEC Corporation OHCI USB Controller (rev 41) (prog-if 10 [OHCI])
	Subsystem: Compaq Computer Corporation Device 004a
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64 (250ns min, 10500ns max), Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 10
	Region 0: Memory at 40180000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [40] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: ohci-pci

02:0e.1 USB controller: NEC Corporation OHCI USB Controller (rev 41) (prog-if 10 [OHCI])
	Subsystem: Compaq Computer Corporation Device 004a
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64 (250ns min, 10500ns max), Cache Line Size: 32 bytes
	Interrupt: pin B routed to IRQ 10
	Region 0: Memory at 40200000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [40] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: ohci-pci

02:0e.2 USB controller: NEC Corporation uPD72010x USB 2.0 Controller (rev 02) (prog-if 20 [EHCI])
	Subsystem: Compaq Computer Corporation Device 004a
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64 (4000ns min, 8500ns max), Cache Line Size: 32 bytes
	Interrupt: pin C routed to IRQ 10
	Region 0: Memory at 40280000 (32-bit, non-prefetchable) [size=256]
	Capabilities: [40] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: ehci-pci

Dernière modification par domi301 (Le 09/10/2015, à 20:16)


Lubuntu / Xubuntu-Voyager ==> redonner vie à des machines abandonnées
en cas de besoin => http://forum.ubuntu-fr.org/viewtopic.php?id=1069631

Hors ligne

#2 Le 07/10/2015, à 20:45

domi301

Re : [RESOLU]connection réseau éthernet impossible intel PRO/100

salut
apparemment un admin a deplacé le post depuis la partie réseau

je maintiens que c'est bien un soucis reseau et non 15.10 vu que j'ai le meme soucis en 14.04...
mais vu qu'il n'y a pas de LTS lubuntu, quitte a essayer lubuntu j'avais pris la derniere/future...


Lubuntu / Xubuntu-Voyager ==> redonner vie à des machines abandonnées
en cas de besoin => http://forum.ubuntu-fr.org/viewtopic.php?id=1069631

Hors ligne

#3 Le 07/10/2015, à 20:48

nam1962

Re : [RESOLU]connection réseau éthernet impossible intel PRO/100

Ton matos ne relève sans doute pas de wily, mais plutôt de la 12.04, voire d'antiX....


[ Modéré ]

Hors ligne

#4 Le 07/10/2015, à 20:55

Olivier63

Re : [RESOLU]connection réseau éthernet impossible intel PRO/100

Bonjour,

D'après le retour de la commande

sudo lspci -vv

il apparaît qu'aucun module n'est chargé pour faire fonctionner la carte ethernet.
Il faut donc trouver quel module utiliser pour ce matériel.
A cette adresse, http://people.via.ecp.fr/~alexis/t30/, il y a un exemple de config avec le même matériel. Attention, la page semble très ancienne puisqu'elle fait référence à un noyau 2.6.9... sorti en 2004 !

A tout hasard, tu peux essayer de charger un des modules suggérés, le e100 par exemple en faisant

sudo modprobe e100

S'il n'y a pas de message d'erreur c'est que le module est chargé. Pour vérifier,

lsmod | grep e100

Si c'est le cas, cela devrait fonctionner. Il ne te resteras plus qu'à configurer le chargement automatique du module au démarrage.

Bon courage !

Hors ligne

#5 Le 07/10/2015, à 23:27

domi301

Re : [RESOLU]connection réseau éthernet impossible intel PRO/100

merci pour vos réponses

j'en étais arrivé aussi a un soucis de driver mais me voyais mal recompiler un noyau...

http://wwwstaff.ari.uni-heidelberg.de/m … l#ethernet
http://cateee.net/lkddb/web-lkddb/EEPRO100.html
http://cateee.net/lkddb/web-lkddb/E100.html

je vais voir pour le modprobe ou sinon essayer avec la 12.04

??? comment savoir si les modules E100 sont inclus ou non dans un noyau ,
existe t'il une liste des modules par noyau ?

[edit]
j'ai trouvé la commande modinfo ici https://doc.ubuntu-fr.org/tutoriel/tout … ules_linux
le module e100 est bien présent en 15.04 (sur ma machine actuelle) je le trouverai peut etre sur la 15.10...

Dernière modification par domi301 (Le 07/10/2015, à 23:39)


Lubuntu / Xubuntu-Voyager ==> redonner vie à des machines abandonnées
en cas de besoin => http://forum.ubuntu-fr.org/viewtopic.php?id=1069631

Hors ligne

#6 Le 08/10/2015, à 09:06

nam1962

Re : [RESOLU]connection réseau éthernet impossible intel PRO/100

..tu es testeur ?


[ Modéré ]

Hors ligne

#7 Le 09/10/2015, à 19:45

domi301

Re : [RESOLU]connection réseau éthernet impossible intel PRO/100

nam1962 a écrit :

..tu es testeur ?

salut nam1962 (et gloire a ton tuto...)
je ne suis pas sur de ce que recouvre ta question, je ne suis pas testeur officiel
mais un peu "joueur" :)


Lubuntu / Xubuntu-Voyager ==> redonner vie à des machines abandonnées
en cas de besoin => http://forum.ubuntu-fr.org/viewtopic.php?id=1069631

Hors ligne

#8 Le 09/10/2015, à 20:09

domi301

Re : [RESOLU]connection réseau éthernet impossible intel PRO/100

grace a vos conseils et un peu d'huile de coude duckduckgo j'ai maté l'ancetre

il y a bien un module e100 qui correspond aux pilotes de pas mal de chipset intel mais qui n'est pas chargé automatiquement
(apparemment un conflit d'eprom qui gene la detection cf les erreurs dans dmesg avec le lancement du e100)
certains preconisent aussi d'installer les firmware-non-free pour debloquer (cf le tuto de nam1962) mais je n'ai pas creusé cette piste

modinfo e100

m'a permis de vérifier qu'il faisait toujours parti de mon kernel actil
on pouvait ensuite forcer l'activation avec

 sudo modprobe e100 

mais ca ne marchait toujours pas...
il a donc fallu le decharger pour les prochains test avec

 sudo modprobe -r e100

apres divers recherches sur askubuntu j'ai decouvert les options qui manquaient

sudo modprobe e100 eeprom_bad_csum_allow=1

j'ai pu tester que tout marchait bien...(ping de ma box puis firefox puis update...)

il ne restait plus qu'a l'activer au demarrage... avec

 sudo nano /etc/modprobe.d/e100.conf 

on met dedans > options e100 eeprom_bad_csum_allow=1
on peut bien sur utiliser gedit a la place de nano ...
il ne reste plus qu'a l'activer avec

 sudo update-initramfs -u 

parmi les sources voir
http://askubuntu.com/questions/122906/m … on-startup

http://askubuntu.com/questions/676707/h … -in-initrd


a noter aussi une piste alternative pour certains pilotes intel
http://askubuntu.com/questions/483022/t … 2ez-10-100


Lubuntu / Xubuntu-Voyager ==> redonner vie à des machines abandonnées
en cas de besoin => http://forum.ubuntu-fr.org/viewtopic.php?id=1069631

Hors ligne

#9 Le 10/10/2015, à 09:25

nam1962

Re : [RESOLU]connection réseau éthernet impossible intel PRO/100

domi301 a écrit :
nam1962 a écrit :

..tu es testeur ?

salut nam1962 (et gloire a ton tuto...)
je ne suis pas sur de ce que recouvre ta question, je ne suis pas testeur officiel
mais un peu "joueur" smile

wink merci

Pour la question, c'est surtout pour que d'éventuels débutants passant sur le fil ne s'inspirent pas de ces "jeux" tongue
Mais comme le fil a été déplacé en section instable c'est plus clair !


[ Modéré ]

Hors ligne

#10 Le 10/10/2015, à 11:47

domi301

Re : [RESOLU]connection réseau éthernet impossible intel PRO/100

oui mais non

j'ai effectivement joué en lubuntu 15.10 (quitte a ne pas avoir de LTS Lubuntu et a devoir formater le bazar pour virer windows XP)

mais mon soucis avec le module e100 qui pilote la carte réseau intel est un probleme GENERIQUE
j'avais le meme blocage d'absence de liaison ethernet avec Xubuntu en 12.04 et 14.04


Lubuntu / Xubuntu-Voyager ==> redonner vie à des machines abandonnées
en cas de besoin => http://forum.ubuntu-fr.org/viewtopic.php?id=1069631

Hors ligne