plus de pilote nvidia

Vaneck · Le 22/09/2019, à 14:58

bonjour
A la base je voulais regler mon pilote en 60 hz. J'ai donc touché le xorg et changé les pilotes graphiques. Depuis c'est comme si je n'ai plus de pilote installé. Les jeux sont injouable et meme les animations ubuntu saccade. J'ai remis à jour le xorg , et tenté de remettre le pilote nvidia originel, rien ne fonctionne. De plus j'ai ce message:

le systeme de paquet est cassé.
Vérifiez si vous utilisez des dépôts de tierces parties. Si c'est le cas, désactivez-les car ils sont une source habituelle de problèmes.
De plus, exécutez la commande suivante dans un  terminal : sudo apt-get install -f
Transaction failed: Le système de paquets est cassé
 Les paquets suivants ont des dépendances non satisfaites :

libnvidia-ifr1-418: Depends: libnvidia-gl-418 mais il n'est pas installé
libnvidia-ifr1-418:i386: Depends: libnvidia-gl-418 mais il n'est pas installé
nvidia-driver-418: Depends: libnvidia-gl-418 (= 418.56-0ubuntu1) mais il n'est pas installé
                   Depends: nvidia-dkms-418 (= 418.56-0ubuntu1) mais la version 418.56-0ubuntu1 est installée
                   Depends: nvidia-kernel-source-418 (= 418.56-0ubuntu1) mais la version 418.56-0ubuntu1 est installée
                   Depends: libnvidia-compute-418 (= 418.56-0ubuntu1) mais la version 418.56-0ubuntu1 est installée
                   Depends: nvidia-compute-utils-418 (= 418.56-0ubuntu1) mais la version 418.56-0ubuntu1 est installée
                   Depends: libnvidia-decode-418 (= 418.56-0ubuntu1) mais la version 418.56-0ubuntu1 est installée
                   Depends: libnvidia-encode-418 (= 418.56-0ubuntu1) mais la version 418.56-0ubuntu1 est installée
                   Depends: nvidia-utils-418 (= 418.56-0ubuntu1) mais la version 418.56-0ubuntu1 est installée
                   Depends: xserver-xorg-video-nvidia-418 (= 418.56-0ubuntu1) mais la version 418.56-0ubuntu1 est installée
                   Depends: libnvidia-cfg1-418 (= 418.56-0ubuntu1) mais la version 418.56-0ubuntu1 est installée
                   Depends: libnvidia-ifr1-418 (= 418.56-0ubuntu1) mais la version 418.56-0ubuntu1 est installée
                   Depends: libnvidia-fbc1-418 (= 418.56-0ubuntu1) mais la version 418.56-0ubuntu1 est installée

merci pour votre aide.

MrKebi · Le 22/09/2019, à 16:06

Hello, SANS accepter, donnes le retour de sudo apt-get install -f

Donnes également le retour de lspci -vv

Vaneck · Le 22/09/2019, à 20:58

merci

vaneck@Hal:~$ sudo apt-get install -f
[sudo] Mot de passe de vaneck : 
Lecture des listes de paquets... Fait
Construction de l'arbre des dépendances       
Lecture des informations d'état... Fait
Correction des dépendances... Fait
Les paquets suivants ont été installés automatiquement et ne sont plus nécessaires :
  gconf-service gconf-service-backend gconf2-common lib32gcc1 libc6-i386
  libgconf-2-4 libglade2-0 libglade2.0-cil libnvidia-common-390
  libnvidia-common-435 libuser1 python-cairo python-glade2 python-gobject-2
  python-gtk2 python-libuser
Veuillez utiliser « sudo apt autoremove » pour les supprimer.
Les paquets supplémentaires suivants seront installés : 
  libnvidia-gl-418 libnvidia-gl-418:i386
Les NOUVEAUX paquets suivants seront installés :
  libnvidia-gl-418 libnvidia-gl-418:i386
0 mis à jour, 2 nouvellement installés, 0 à enlever et 0 non mis à jour.
3 partiellement installés ou enlevés.
Il est nécessaire de prendre 0 o/49,1 Mo dans les archives.
Après cette opération, 236 Mo d'espace disque supplémentaires seront utilisés.
Souhaitez-vous continuer ? [O/n]

vaneck@Hal:~$ lspci -vv
00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor DRAM Controller (rev 09)
	Subsystem: ASUSTeK Computer Inc. Xeon E3-1200 v2/3rd Gen Core processor DRAM Controller
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: <access denied>
	Kernel driver in use: ivb_uncore
	Kernel modules: ie31200_edac

00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor PCI Express Root Port (rev 09) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 16
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	I/O behind bridge: 0000e000-0000efff
	Memory behind bridge: f6000000-f70fffff
	Prefetchable memory behind bridge: 00000000e8000000-00000000f1ffffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04)
	Subsystem: ASUSTeK Computer Inc. P8 series motherboard
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 36
	Region 0: Memory at f730a000 (64-bit, non-prefetchable) [size=16]
	Capabilities: <access denied>
	Kernel driver in use: mei_me
	Kernel modules: mei_me

00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) (prog-if 20 [EHCI])
	Subsystem: ASUSTeK Computer Inc. P8 series motherboard
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 23
	Region 0: Memory at f7308000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access denied>
	Kernel driver in use: ehci-pci

00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05)
	Subsystem: ASUSTeK Computer Inc. 6 Series/C200 Series Chipset Family High Definition Audio Controller
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 37
	Region 0: Memory at f7300000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: snd_hda_intel
	Kernel modules: snd_hda_intel

00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 16
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin B routed to IRQ 17
	Bus: primary=00, secondary=03, subordinate=04, sec-latency=0
	I/O behind bridge: 0000d000-0000dfff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin C routed to IRQ 18
	Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
	I/O behind bridge: 0000c000-0000cfff
	Prefetchable memory behind bridge: 00000000f2100000-00000000f21fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin D routed to IRQ 19
	Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
	Memory behind bridge: f7200000-f72fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

00:1c.4 PCI bridge: Intel Corporation 82801 PCI Bridge (rev b5) (prog-if 01 [Subtractive decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 11
	Bus: primary=00, secondary=07, subordinate=08, sec-latency=0
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>

00:1c.5 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 6 (rev b5) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin B routed to IRQ 17
	Bus: primary=00, secondary=09, subordinate=09, sec-latency=0
	I/O behind bridge: 0000b000-0000bfff
	Memory behind bridge: f7100000-f71fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) (prog-if 20 [EHCI])
	Subsystem: ASUSTeK Computer Inc. P8 series motherboard
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 23
	Region 0: Memory at f7307000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access denied>
	Kernel driver in use: ehci-pci

00:1f.0 ISA bridge: Intel Corporation H61 Express Chipset LPC Controller (rev 05)
	Subsystem: ASUSTeK Computer Inc. H61 Express Chipset LPC Controller
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: <access denied>
	Kernel driver in use: lpc_ich
	Kernel modules: lpc_ich

00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port Desktop SATA AHCI Controller (rev 05) (prog-if 01 [AHCI 1.0])
	Subsystem: ASUSTeK Computer Inc. P8 series motherboard
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 34
	Region 0: I/O ports at f070 [size=8]
	Region 1: I/O ports at f060 [size=4]
	Region 2: I/O ports at f050 [size=8]
	Region 3: I/O ports at f040 [size=4]
	Region 4: I/O ports at f020 [size=32]
	Region 5: Memory at f7306000 (32-bit, non-prefetchable) [size=2K]
	Capabilities: <access denied>
	Kernel driver in use: ahci
	Kernel modules: ahci

00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05)
	Subsystem: ASUSTeK Computer Inc. P8 series motherboard
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin C routed to IRQ 18
	Region 0: Memory at f7305000 (64-bit, non-prefetchable) [size=256]
	Region 4: I/O ports at f000 [size=32]
	Kernel driver in use: i801_smbus
	Kernel modules: i2c_i801

01:00.0 VGA compatible controller: NVIDIA Corporation GK106 [GeForce GTX 660] (rev a1) (prog-if 00 [VGA controller])
	Subsystem: Micro-Star International Co., Ltd. [MSI] GK106 [GeForce GTX 660]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 38
	Region 0: Memory at f6000000 (32-bit, non-prefetchable) [size=16M]
	Region 1: Memory at e8000000 (64-bit, prefetchable) [size=128M]
	Region 3: Memory at f0000000 (64-bit, prefetchable) [size=32M]
	Region 5: I/O ports at e000 [size=128]
	[virtual] Expansion ROM at 000c0000 [disabled] [size=128K]
	Capabilities: <access denied>
	Kernel driver in use: nvidia
	Kernel modules: nvidiafb, nouveau, nvidia_drm, nvidia

01:00.1 Audio device: NVIDIA Corporation GK106 HDMI Audio Controller (rev a1)
	Subsystem: Micro-Star International Co., Ltd. [MSI] GK106 HDMI Audio Controller
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin B routed to IRQ 17
	Region 0: Memory at f7080000 (32-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: snd_hda_intel
	Kernel modules: snd_hda_intel

03:00.0 PCI bridge: PLX Technology, Inc. PEX8112 x1 Lane PCI Express-to-PCI Bridge (rev aa) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 17
	Bus: primary=03, secondary=04, subordinate=04, sec-latency=64
	I/O behind bridge: 0000d000-0000dfff
	Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>

04:04.0 Multimedia audio controller: C-Media Electronics Inc CMI8788 [Oxygen HD Audio]
	Subsystem: ASUSTeK Computer Inc. Virtuoso 100 (Xonar DX)
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64 (500ns min, 6000ns max)
	Interrupt: pin A routed to IRQ 17
	Region 0: I/O ports at d000 [size=256]
	Capabilities: <access denied>
	Kernel driver in use: snd_virtuoso
	Kernel modules: snd_virtuoso

05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 06)
	Subsystem: ASUSTeK Computer Inc. P8P67 and other motherboards
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 18
	Region 0: I/O ports at c000 [size=256]
	Region 2: Memory at f2104000 (64-bit, prefetchable) [size=4K]
	Region 4: Memory at f2100000 (64-bit, prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: r8169
	Kernel modules: r8169

06:00.0 USB controller: ASMedia Technology Inc. ASM1042 SuperSpeed USB Host Controller (prog-if 30 [XHCI])
	Subsystem: ASUSTeK Computer Inc. P8B WS Motherboard
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 19
	Region 0: Memory at f7200000 (64-bit, non-prefetchable) [size=32K]
	Capabilities: <access denied>
	Kernel driver in use: xhci_hcd

07:00.0 PCI bridge: ASMedia Technology Inc. ASM1083/1085 PCIe to PCI Bridge (rev 01) (prog-if 01 [Subtractive decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 11
	Bus: primary=07, secondary=08, subordinate=08, sec-latency=64
	Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>

09:00.0 SATA controller: ASMedia Technology Inc. ASM1062 Serial ATA Controller (rev 01) (prog-if 01 [AHCI 1.0])
	Subsystem: ASUSTeK Computer Inc. ASM1062 Serial ATA Controller
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 35
	Region 0: I/O ports at b050 [size=8]
	Region 1: I/O ports at b040 [size=4]
	Region 2: I/O ports at b030 [size=8]
	Region 3: I/O ports at b020 [size=4]
	Region 4: I/O ports at b000 [size=32]
	Region 5: Memory at f7100000 (32-bit, non-prefetchable) [size=512]
	Capabilities: <access denied>
	Kernel driver in use: ahci
	Kernel modules: ahci

MrKebi · Le 22/09/2019, à 22:48

Ok essaies sudo apt-get update -f et acceptes cette fois-ci. Dis moi si c'est mieux après.

Dernière modification par MrKebi (Le 22/09/2019, à 22:48)

Vaneck · Le 23/09/2019, à 02:51

vaneck@Hal:~$ sudo apt-get update -f
E: L'option « f » de la ligne de commande [-f] n'est pas reconnue quand elle est utilisée avec d'autres options.

MrKebi · Le 23/09/2019, à 03:16

Erreur de ma part dans la commande ; sudo apt-get install -f

Vaneck · Le 23/09/2019, à 13:59

vaneck@Hal:~$ sudo apt-get install -f
[sudo] Mot de passe de vaneck : 
Lecture des listes de paquets... Fait
Construction de l'arbre des dépendances       
Lecture des informations d'état... Fait
Correction des dépendances... Fait
Les paquets suivants ont été installés automatiquement et ne sont plus nécessaires :
  gconf-service gconf-service-backend gconf2-common lib32gcc1 libc6-i386
  libgconf-2-4 libglade2-0 libglade2.0-cil libnvidia-common-390
  libnvidia-common-435 libuser1 python-cairo python-glade2 python-gobject-2
  python-gtk2 python-libuser
Veuillez utiliser « sudo apt autoremove » pour les supprimer.
Les paquets supplémentaires suivants seront installés : 
  libnvidia-gl-418 libnvidia-gl-418:i386
Les NOUVEAUX paquets suivants seront installés :
  libnvidia-gl-418 libnvidia-gl-418:i386
0 mis à jour, 2 nouvellement installés, 0 à enlever et 0 non mis à jour.
3 partiellement installés ou enlevés.
Il est nécessaire de prendre 0 o/49,1 Mo dans les archives.
Après cette opération, 236 Mo d'espace disque supplémentaires seront utilisés.
Souhaitez-vous continuer ? [O/n] O
(Lecture de la base de données... 230717 fichiers et répertoires déjà installés.)
Préparation du dépaquetage de .../libnvidia-gl-418_418.56-0ubuntu1_i386.deb ...
détournement de /usr/lib/i386-linux-gnu/libGL.so.1 en /usr/lib/i386-linux-gnu/libGL.so.1.distrib par nvidia-340
dpkg-divert: erreur: erreur de correspondance sur paquet
  lors de la suppression de « détournement de /usr/lib/i386-linux-gnu/libGL.so.1 par libnvidia-gl-418 »
  « détournement de /usr/lib/i386-linux-gnu/libGL.so.1 en /usr/lib/i386-linux-gnu/libGL.so.1.distrib par nvidia-340 » trouvé
dpkg: erreur de traitement de l'archive /var/cache/apt/archives/libnvidia-gl-418_418.56-0ubuntu1_i386.deb (--unpack) :
 new libnvidia-gl-418:i386 package pre-installation script subprocess returned error exit status 2
Préparation du dépaquetage de .../libnvidia-gl-418_418.56-0ubuntu1_amd64.deb ...
détournement de /usr/lib/x86_64-linux-gnu/libGL.so.1 en /usr/lib/x86_64-linux-gnu/libGL.so.1.distrib par nvidia-340
dpkg-divert: erreur: erreur de correspondance sur paquet
  lors de la suppression de « détournement de /usr/lib/x86_64-linux-gnu/libGL.so.1 par libnvidia-gl-418 »
  « détournement de /usr/lib/x86_64-linux-gnu/libGL.so.1 en /usr/lib/x86_64-linux-gnu/libGL.so.1.distrib par nvidia-340 » trouvé
dpkg: erreur de traitement de l'archive /var/cache/apt/archives/libnvidia-gl-418_418.56-0ubuntu1_amd64.deb (--unpack) :
 new libnvidia-gl-418:amd64 package pre-installation script subprocess returned error exit status 2
Des erreurs ont été rencontrées pendant l'exécution :
 /var/cache/apt/archives/libnvidia-gl-418_418.56-0ubuntu1_i386.deb
 /var/cache/apt/archives/libnvidia-gl-418_418.56-0ubuntu1_amd64.deb
E: Sub-process /usr/bin/dpkg returned an error code (1)
vaneck@Hal:~$

Vaneck · Le 24/09/2019, à 22:30

du coup c'est bloqué?

Vaneck · Le 25/09/2019, à 12:35

y a un moyen de réparer sans formater?

Ubuntu-fr

Navigation

Liens de recherche

Annonce

#1 Le 22/09/2019, à 14:58

plus de pilote nvidia

#2 Le 22/09/2019, à 16:06

Re : plus de pilote nvidia

#3 Le 22/09/2019, à 20:58

Re : plus de pilote nvidia

#4 Le 22/09/2019, à 22:48

Re : plus de pilote nvidia

#5 Le 23/09/2019, à 02:51

Re : plus de pilote nvidia

#6 Le 23/09/2019, à 03:16

Re : plus de pilote nvidia

#7 Le 23/09/2019, à 13:59

Re : plus de pilote nvidia

#8 Le 24/09/2019, à 22:30

Re : plus de pilote nvidia

#9 Le 25/09/2019, à 12:35

Re : plus de pilote nvidia

Pied de page des forums