Pages : 1
#1 Le 03/03/2007, à 23:02
- Lemmy78
pinnacle pctv pro = no signal
Salut à tous,
Je viens de ressortir ma carte pinnacle pctv pro des cartons pour l'installer sous ubuntu 6.10 et je galère...
J'ai lu pas mal de tuto et rien n'y fait. j'utilise tvtime et à cahque fois j'ai "no signal".
La carte et bien détectée :
00:0e.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
Subsystem: Pinnacle Systems Inc. PCTV pro (TV + FM stereo receiver)
Flags: bus master, medium devsel, latency 32, IRQ 185
Memory at df000000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
00:0e.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
Subsystem: Pinnacle Systems Inc. PCTV pro (TV + FM stereo receiver, audio section)
Flags: medium devsel, IRQ 185
Memory at de800000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. A7V8X-X motherboard
Flags: bus master, medium devsel, latency 32, IRQ 169
I/O ports at d400 [size=32]
Capabilities: [80] Power Management version 2
J'ai configuré bttv et un dmesg | grep bttv me donne ceci:
[17179589.516000] bttv: driver version 0.9.16 loaded
[17179589.516000] bttv: using 4 buffers with 2080k (520 pages) each for capture
[17179589.520000] bttv: Bt8xx card found (0).
[17179589.520000] bttv0: Bt878 (rev 17) at 0000:00:0e.0, irq: 185, latency: 32, mmio: 0xdf000000
[17179589.520000] bttv0: detected: Pinnacle PCTV [card=39], PCI subsystem ID is 11bd:0012
[17179589.520000] bttv0: using: Pinnacle PCTV Studio/Rave [card=39,insmod option]
[17179589.520000] bttv0: gpio: en=00000000, out=00000000 in=00fffbff [init]
[17179589.524000] bttv0: i2c: checking for MSP34xx @ 0x80... found
[17179589.524000] bttv0: pinnacle/mt: id=2 info="PAL+SECAM / stereo" radio=yes
[17179589.524000] bttv0: using tuner=3
[17179589.524000] bttv0: i2c: checking for MSP34xx @ 0x80... found
[17179589.592000] bttv0: i2c: checking for TDA9875 @ 0xb0... not found
[17179589.596000] bttv0: i2c: checking for TDA7432 @ 0x8a... not found
[17179589.692000] bttv0: registered device video0
[17179589.696000] bttv0: registered device vbi0
[17179589.696000] bttv0: registered device radio0
[17179589.764000] bttv0: PLL: 28636363 => 35468950 .. ok
[17179980.296000] bttv0: PLL can sleep, using XTAL (28636363).
[17181969.744000] bttv0: PLL: 28636363 => 35468950 .. ok
[17182036.836000] bttv0: timeout: drop=743 irq=17172/17172, risc=0d779054, bits: HSYNC OFLOW FDSR
[17182036.836000] bttv0: reset, reinitialize
[17182036.868000] bttv0: PLL: 28636363 => 35468950 . ok
[17182203.552000] bttv0: PLL can sleep, using XTAL (28636363).
J'ai essayé aussi avec XawTV mais il ne lance pas.
Si qqu'un peut m'aider ça serait cool...
Merci
Ubuntu 16.04LTS - 64 Bits
If it is too loud then you're too old !!!!
Hors ligne
#2 Le 04/03/2007, à 13:01
- Lemmy78
Re : pinnacle pctv pro = no signal
personne ???
Ubuntu 16.04LTS - 64 Bits
If it is too loud then you're too old !!!!
Hors ligne
#3 Le 08/03/2007, à 00:05
- rickpier
Re : pinnacle pctv pro = no signal
creer un fichier bttv dans /etc/modprobe.d/ et ajoutes y:
options bttv radio=0 card=34 tuner=3 gbuffers=8
ajoutes alafin du fichier dans /etc/modules :
bttv
Et voila en fait le peripherique sera demarre (d'apres ce que j'ai compris)
apres si t'as pas l'audio...tu cherches et tu me donnes la reponse
#4 Le 08/03/2007, à 00:07
- rickpier
Re : pinnacle pctv pro = no signal
oups tot c'est card=39 a priori
#5 Le 08/03/2007, à 00:08
- rickpier
Re : pinnacle pctv pro = no signal
et radio=1 vu que t'as la radio....
#6 Le 08/03/2007, à 10:17
- Lemmy78
Re : pinnacle pctv pro = no signal
Merci mais tout cela est déjà fait...
Et toujours no signal
Ubuntu 16.04LTS - 64 Bits
If it is too loud then you're too old !!!!
Hors ligne
Pages : 1