#1 Le 01/12/2007, à 08:47
- jmc_Marseille
[RESOLU] Gusty - Ubuntu - Nvidia 7600 GS - Double ecran - Compiz
Bonjour,
Après avoir pas mal galéré pour installer ma carte nvidia 7600 GS et profiter pleinement de ma configuration : un 22" et un 17" (tout deux flat), je met au cas ou d'autre ramerai sur cette install la procédure qui me permet de profiter d'un joli cube qui tourne (pas vite hélas) et surtout de pouvoir profiter de l'accélarion graphique et de mes deux écrans :
Donc :
d'abord, configuration de l'écran principal (mon 22" Siemens)
j'ai installé ubuntu mais pas moyen d'installer le driver nvidia. avec nv, bonne résolution, avec nvidia pas moyen. basse resolution.
tout essayé : envy, pilote nvidia, pilote par defaut. rien a faire toujours le même résu.
suite a des conseils sur le forum, j'ai testé les lignes suivantes :
cat /proc/driver/nvidia/agp/cardFast Writes: Supported
SBA: Supported
AGP Rates: 8x 4x
Registers: 0xff000e1b:0x1f004302
cat /proc/driver/nvidia/agp/host-bridgeHost Bridge: PCI device 8086:2570
Fast Writes: Supported
SBA: Supported
AGP Rates: 8x 4x
Registers: 0x1f004a1b:0x00000b02
j'avais bien l'accélation graphique donc il fallait chercher du coté de la résolution.
j'ai donc lancé les commandes pour reconfigurer le xserver
sudo dpkg-reconfigure -phigh xserver-xorget regénéré le xorg.conf mais toujours le même problème.
suite a une réponse a mes appels a l'aide, on m'informe que sous Kubuntu, pas de problème.
j'install donc Kubuntu et je configure avec le drivers propriétaire installé d'office par gusty.
et hop même probleme resolution basse avec nvidia.
je lance sudo dpkg-reconfigure -phigh xserver-xorg
et la, j'obtiens la configuration du monitor en ayant je le précise fait les mêmes manip qu'avec ubuntu. (je ne me l'explique pas).
donc je sauvegarde ce xorg.conf sur un disque qui ne sera pas touché par l'installation, je réinstalle ubuntu
par curiosité et besoin de perdre un peu de temps, je refait les meme manip sur ma config toute neuve et rien a faire, sudo dpkg-reconfigure -phigh xserver-xorg ne me donne pas du tout les meme informations.
sans rien faire de plus (ni désinstalle de nvidia, ni install d'autre chose, je copie le xorg.conf généré sous kubuntu et hop je relance x et ça marche ????
ensuite, configurer compiz et le deuxième écran avec l'aide de différents post fut un jeu d'enfant.
je donne donc ce xorg.conf en précisant qu'il fonctionne avec les drivers nvidia installé par défaut nvidia-glx-new et compiz le tout installer par apt-get :
sudo apt-get install nvidia-glx-new
sudo apt-get install compiz
sudo apt-get install compizconfig-settings-manager
a chaque fois, refaire la ligne avec les paquets suggérés ou conseillés
# /etc/X11/xorg.conf (xorg X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
#
# Edit this file with caution, and see the xorg.conf(5) manual page.
# (Type "man xorg.conf" at the shell prompt.)
#
# This file is automatically updated on xserver-xorg package upgrades *only*
# if it has not been modified since the last upgrade of the xserver-xorg
# package.
#
# If you have edited this file but would like it to be automatically updated
# again, run the following command:
# sudo dpkg-reconfigure -phigh xserver-xorg
Section "Files"
Fontpath "/usr/share/fonts/X11/misc"
Fontpath "/usr/share/fonts/X11/cyrillic"
Fontpath "/usr/share/fonts/X11/100dpi/:unscaled"
Fontpath "/usr/share/fonts/X11/75dpi/:unscaled"
Fontpath "/usr/share/fonts/X11/Type1"
Fontpath "/usr/share/fonts/X11/100dpi"
Fontpath "/usr/share/fonts/X11/75dpi"
# path to defoma fonts
Fontpath "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType"
EndSection
Section "Module"
Load "i2c"
Load "bitmap"
Load "ddc"
Load "extmod"
Load "freetype"
Load "int10"
Load "vbe"
Load "glx"
Load "v4l"
EndSection
Section "InputDevice"
Identifier "Generic Keyboard"
Driver "kbd"
Option "CoreKeyboard"
Option "XkbRules" "xorg"
Option "XkbModel" "pc105"
Option "XkbLayout" "fr"
Option "XkbVariant" "oss"
EndSection
Section "InputDevice"
Identifier "Configured Mouse"
Driver "mouse"
Option "CorePointer"
Option "Device" "/dev/input/mice"
Option "Protocol" "ImPS/2"
Option "ZAxisMapping" "4 5"
Option "Emulate3Buttons" "true"
EndSection
Section "InputDevice"
Driver "wacom"
Identifier "stylus"
Option "Device" "/dev/input/wacom"
Option "Type" "stylus"
Option "ForceDevice" "ISDV4"# Tablet PC ONLY
EndSection
Section "InputDevice"
Driver "wacom"
Identifier "eraser"
Option "Device" "/dev/input/wacom"
Option "Type" "eraser"
Option "ForceDevice" "ISDV4"# Tablet PC ONLY
EndSection
Section "InputDevice"
Driver "wacom"
Identifier "cursor"
Option "Device" "/dev/input/wacom"
Option "Type" "cursor"
Option "ForceDevice" "ISDV4"# Tablet PC ONLY
EndSection
Section "Device"
Identifier "0"
Boardname "NVIDIA GeForce 7 Series"
Busid "PCI:1:0:0"
Driver "nvidia"
Screen 0
Vendorname "NVIDIA"
# Option "TwinView" "true"
# Option "TwinViewOrientation" "RightOf"
# Option "TVOutFormat" "COMPOSITE"
# Option "TVStandard" "PAL-N"
# Option "SecondMonitorHorizSync" "30-50"
# Option "SecondMonitorVertRefresh" "60"
# Option "MetaModes" "1024x768,1024x768;800x600,800x600;640x480,640x480;512x384,512x384"
# Option "AddARGBVisuals" "True"
# Option "AddARGBGLXVisuals" "True"
# Option "NoLogo" "True"
EndSection
Section "Device"
Identifier "1"
Boardname "NVIDIA GeForce 7 Series"
Busid "PCI:1:0:0"
Driver "nvidia"
Screen 1
Vendorname "NVIDIA"
# Option "TwinView" "true"
# Option "TwinViewOrientation" "RightOf"
# Option "TVOutFormat" "COMPOSITE"
# Option "TVStandard" "PAL-N"
# Option "SecondMonitorHorizSync" "30-50"
# Option "SecondMonitorVertRefresh" "60"
# Option "MetaModes" "1024x768,1024x768;800x600,800x600;640x480,640x480;512x384,512x384"
# Option "AddARGBVisuals" "True"
# Option "AddARGBGLXVisuals" "True"
# Option "NoLogo" "True"
EndSection
Section "Monitor"
Identifier "Monitor0"
Vendorname "Generic"
Modelname "Flat Panel 1680x1050"
Horizsync 31.5-90
Vertrefresh 60
modeline "1680x1050@60" 147.14 1680 1784 1968 2256 1050 1051 1054 1087 -hsync +vsync
Gamma 1.0
EndSection
Section "Monitor"
Identifier "Monitor1"
VendorName "Plug'n Play"
ModelName "Flat Panel 1024x768"
HorizSync 30.0 - 71.0
VertRefresh 56.0 - 75.0
ModeLine "1024x768" 65.00 1024 1032 1176 1344 480 488 494 563 -hsync -vsync
Gamma 1.0
EndSection
Section "Screen"
Identifier "Screen0"
Device "0"
Monitor "Monitor0"
Defaultdepth 24
Option "NoPowerConnectorCheck"
Option "TwinView" "0"
SubSection "Display"
Depth 24
# Virtual 1920 1200
Modes "1680x1050@60"
EndSubSection
EndSection
Section "Screen"
Identifier "Screen1"
Device "1"
Monitor "Monitor1"
Defaultdepth 24
Option "NoPowerConnectorCheck"
Option "TwinView" "0"
Option "metamodes" "DFP-1: nvidia-auto-select +0+0"
SubSection "Display"
Depth 24
EndSubSection
EndSection
Section "ServerLayout"
Identifier "Default Layout"
screen 0 "Screen0" 0 0
screen 1 "Screen1" RightOf "Screen0"
Inputdevice "Generic Keyboard"
Inputdevice "Configured Mouse"
Inputdevice "stylus" "SendCoreEvents"
Inputdevice "cursor" "SendCoreEvents"
Inputdevice "eraser" "SendCoreEvents"
EndSection
Section "ServerFlags"
Option "Xinerama" "0"
EndSection
Section "DRI"
Mode 0666
EndSection
Section "ServerFlags"
EndSectionpour informations je met ici le resu d'un lshw
description: Computer
width: 32 bits
*-core
description: Motherboard
physical id: 0
*-memory
description: System memory
physical id: 0
size: 2026MB
*-cpu
product: Intel(R) Pentium(R) 4 CPU 2.40GHz
vendor: Intel Corp.
physical id: 1
bus info: cpu@0
version: 15.2.9
size: 18EHz
width: 32 bits
capabilities: fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe cid xtpr
configuration: id=0
*-logicalcpu:0
description: Logical CPU
physical id: 0.1
width: 32 bits
capabilities: logical
*-logicalcpu:1
description: Logical CPU
physical id: 0.2
width: 32 bits
capabilities: logical
*-cache:0
description: L1 cache
physical id: 0
size: 8KB
*-cache:1
description: L2 cache
physical id: 1
size: 512KB
*-pci
description: Host bridge
product: 82865G/PE/P DRAM Controller/Host-Hub Interface
vendor: Intel Corporation
physical id: 100
bus info: pci@0000:00:00.0
version: 02
width: 32 bits
clock: 33MHz
configuration: driver=agpgart-intel module=intel_agp
*-pci:0
description: PCI bridge
product: 82865G/PE/P PCI to AGP Controller
vendor: Intel Corporation
physical id: 1
bus info: pci@0000:00:01.0
version: 02
width: 32 bits
clock: 66MHz
capabilities: pci normal_decode bus_master
*-display
description: VGA compatible controller
product: G73 [GeForce 7600 GS]
vendor: nVidia Corporation
physical id: 0
bus info: pci@0000:01:00.0
version: a2
width: 32 bits
clock: 66MHz
capabilities: vga bus_master cap_list
configuration: driver=nvidia latency=248 maxlatency=1 mingnt=5 module=nvidia
*-usb:0
description: USB Controller
product: 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1
vendor: Intel Corporation
physical id: 1d
bus info: pci@0000:00:1d.0
version: 02
width: 32 bits
clock: 33MHz
capabilities: uhci bus_master
configuration: driver=uhci_hcd latency=0 module=uhci_hcd
*-usb:1
description: USB Controller
product: 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2
vendor: Intel Corporation
physical id: 1d.1
bus info: pci@0000:00:1d.1
version: 02
width: 32 bits
clock: 33MHz
capabilities: uhci bus_master
configuration: driver=uhci_hcd latency=0 module=uhci_hcd
*-usb:2
description: USB Controller
product: 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3
vendor: Intel Corporation
physical id: 1d.2
bus info: pci@0000:00:1d.2
version: 02
width: 32 bits
clock: 33MHz
capabilities: uhci bus_master
configuration: driver=uhci_hcd latency=0 module=uhci_hcd
*-usb:3
description: USB Controller
product: 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #4
vendor: Intel Corporation
physical id: 1d.3
bus info: pci@0000:00:1d.3
version: 02
width: 32 bits
clock: 33MHz
capabilities: uhci bus_master
configuration: driver=uhci_hcd latency=0 module=uhci_hcd
*-usb:4
description: USB Controller
product: 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller
vendor: Intel Corporation
physical id: 1d.7
bus info: pci@0000:00:1d.7
version: 02
width: 32 bits
clock: 33MHz
capabilities: ehci bus_master cap_list
configuration: driver=ehci_hcd latency=0 module=ehci_hcd
*-pci:1
description: PCI bridge
product: 82801 PCI Bridge
vendor: Intel Corporation
physical id: 1e
bus info: pci@0000:00:1e.0
version: c2
width: 32 bits
clock: 33MHz
capabilities: pci normal_decode bus_master
*-network
description: Ethernet interface
product: RTL-8139/8139C/8139C+
vendor: Realtek Semiconductor Co., Ltd.
physical id: 5
bus info: pci@0000:02:05.0
logical name: eth0
version: 10
serial: 00:13:8f:f4:2b:a0
width: 32 bits
clock: 33MHz
capabilities: bus_master cap_list ethernet physical
configuration: broadcast=yes driver=8139too driverversion=0.9.28 ip=192.168.0.54 latency=32 maxlatency=64 mingnt=32 module=8139too multicast=yes
*-isa
description: ISA bridge
product: 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge
vendor: Intel Corporation
physical id: 1f
bus info: pci@0000:00:1f.0
version: 02
width: 32 bits
clock: 33MHz
capabilities: isa bus_master
configuration: latency=0
*-ide:0
description: IDE interface
product: 82801EB/ER (ICH5/ICH5R) IDE Controller
vendor: Intel Corporation
physical id: 1f.1
bus info: pci@0000:00:1f.1
logical name: scsi0
version: 02
width: 32 bits
clock: 33MHz
capabilities: ide bus_master emulated
configuration: driver=ata_piix latency=0 module=ata_piix
*-cdrom
description: DVD reader
product: DVD-ROM SD-616E
vendor: SAMSUNG
physical id: 0.0.0
bus info: scsi@0:0.0.0
logical name: /dev/cdrom
logical name: /dev/dvd
logical name: /dev/scd0
logical name: /dev/sr0
version: F501
capabilities: removable audio dvd
configuration: ansiversion=5 status=open
*-ide:1
description: IDE interface
product: 82801EB (ICH5) SATA Controller
vendor: Intel Corporation
physical id: 1f.2
bus info: pci@0000:00:1f.2
version: 02
width: 32 bits
clock: 66MHz
capabilities: ide bus_master
configuration: driver=ata_piix latency=0 module=ata_piix
*-serial UNCLAIMED
description: SMBus
product: 82801EB/ER (ICH5/ICH5R) SMBus Controller
vendor: Intel Corporation
physical id: 1f.3
bus info: pci@0000:00:1f.3
version: 02
width: 32 bits
clock: 33MHz
configuration: latency=0
*-multimedia
description: Multimedia audio controller
product: 82801EB/ER (ICH5/ICH5R) AC'97 Audio Controller
vendor: Intel Corporation
physical id: 1f.5
bus info: pci@0000:00:1f.5
version: 02
width: 32 bits
clock: 33MHz
capabilities: bus_master cap_list
configuration: driver=Intel ICH latency=0 module=snd_intel8x0
*-scsi
physical id: 1
bus info: scsi@4
logical name: scsi4
capabilities: scsi-host
configuration: driver=usb-storagevoilà et merci de l'aide que beaucoup m'ont apporté.
Jean Marc 
Dernière modification par jmc_Marseille (Le 06/12/2007, à 09:00)
Gusty 7.10 - Nvidia 7600 GS - Double Ecran - Compiz
http://parrains.linux.free.fr
Hors ligne