Ubuntu-fr

Azka

Boot relativement lent.

Bonjour, j'ai installé Ubuntu il y a quelques jours et je trouve qu'il met pas mal de temps à se lancer (j'ai chronométré 1min entre l'appui sur entrée dans le grub et l'affichage du bureau).

La référence de mon DD est WDC WD3200BPVT-22ZEST0, il y a écrit 3gb/s dessus, il vient d'un pc portable qui me servait plus et je me suis dit que ça pouvait venir de là mais je préfère être sûr (il est pas si vieux que ça non plus).
Sinon en config j'utilise un FX 8320 et en carte graphique une 280x (je précise au cas où).

J'ai regardé le contenu de var/log/dmesg et j'ai ça :

[    2.009483] usb 11-1: New USB device found, idVendor=0bc2, idProduct=a013
[    2.009486] usb 11-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[    2.009488] usb 11-1: Product: Backup+ BK
[    2.009489] usb 11-1: Manufacturer: Seagate
[    2.009491] usb 11-1: SerialNumber: NA5C5JFK
[    2.012101] usb 11-1: USB controller 0000:04:00.0 does not support streams, which are required by the UAS driver.
[    2.012103] usb 11-1: Please try an other USB controller if you wish to use UAS.
[    2.012105] usb-storage 11-1:1.0: USB Mass Storage device detected
[    2.012192] usb-storage 11-1:1.0: Quirks match for vid 0bc2 pid a013: 2000000
[    2.012225] scsi6 : usb-storage 11-1:1.0
[    2.012290] usbcore: registered new interface driver usb-storage
[    2.013655] usbcore: registered new interface driver uas
[    2.015411] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[    2.015414] cdrom: Uniform CD-ROM driver Revision: 3.20
[    2.015571] sr 2:0:0:0: Attached scsi CD-ROM sr0
[    2.015648] sr 2:0:0:0: Attached scsi generic sg1 type 5
[    2.015798] scsi 4:0:0:0: Direct-Access     ATA      WDC WD3200BPVT-2 1A01 PQ: 0 ANSI: 5
[    2.016017] sd 4:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[    2.016020] sd 4:0:0:0: [sdb] 4096-byte physical blocks
[    2.016049] sd 4:0:0:0: Attached scsi generic sg2 type 0
[    2.016125] sd 4:0:0:0: [sdb] Write Protect is off
[    2.016130] sd 4:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    2.016163] sd 4:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.060943] firewire_core 0000:05:0e.0: created device fw0: GUID 0049e5502a980d00, S400
[    2.093009]  sdb: sdb1 sdb2 sdb3
[    2.093413] sd 4:0:0:0: [sdb] Attached SCSI disk
[    2.132774] tsc: Refined TSC clocksource calibration: 3516.097 MHz
[    2.144689] usb 4-1: new low-speed USB device number 2 using ohci-pci
[    2.309750] usb 4-1: New USB device found, idVendor=093a, idProduct=2521
[    2.309757] usb 4-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[    2.309762] usb 4-1: Product: USB OPTICAL MOUSE
[    2.317536] hidraw: raw HID events driver (C) Jiri Kosina
[    2.323013] usbcore: registered new interface driver usbhid
[    2.323015] usbhid: USB HID core driver
[    2.324509] input: USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:12.0/usb4/4-1/4-1:1.0/0003:093A:2521.0001/input/input5
[    2.324655] hid-generic 0003:093A:2521.0001: input,hidraw0: USB HID v1.11 Mouse [USB OPTICAL MOUSE] on usb-0000:00:12.0-1/input0
[    2.448536] usb 4-2: new low-speed USB device number 3 using ohci-pci
[    2.603927] EXT4-fs (sdb1): INFO: recovery required on readonly filesystem
[    2.603929] EXT4-fs (sdb1): write access will be enabled during recovery
[    2.619498] usb 4-2: New USB device found, idVendor=258a, idProduct=0001
[    2.619505] usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.619510] usb 4-2: Product: USB KEYBOARD
[    2.619514] usb 4-2: Manufacturer: SINO WEALTH
[    2.627863] input: SINO WEALTH USB KEYBOARD as /devices/pci0000:00/0000:00:12.0/usb4/4-2/4-2:1.0/0003:258A:0001.0002/input/input6
[    2.628016] hid-generic 0003:258A:0001.0002: input,hidraw1: USB HID v1.10 Keyboard [SINO WEALTH USB KEYBOARD] on usb-0000:00:12.0-2/input0
[    2.640512] input: SINO WEALTH USB KEYBOARD as /devices/pci0000:00/0000:00:12.0/usb4/4-2/4-2:1.1/0003:258A:0001.0003/input/input7
[    2.640706] hid-generic 0003:258A:0001.0003: input,hiddev0,hidraw2: USB HID v1.10 Device [SINO WEALTH USB KEYBOARD] on usb-0000:00:12.0-2/input1
[    3.008352] scsi 6:0:0:0: Direct-Access     Seagate  Backup+ BK       0412 PQ: 0 ANSI: 6
[    3.008604] sd 6:0:0:0: Attached scsi generic sg3 type 0
[    3.008729] sd 6:0:0:0: [sdc] 1953525167 512-byte logical blocks: (1.00 TB/931 GiB)
[    3.008942] sd 6:0:0:0: [sdc] Write Protect is off
[    3.008945] sd 6:0:0:0: [sdc] Mode Sense: 4f 00 00 00
[    3.009153] sd 6:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.009997] random: nonblocking pool is initialized
[    3.010883]  sdc: sdc1
[    3.011697] sd 6:0:0:0: [sdc] Attached SCSI disk
[    3.132000] Switched to clocksource tsc
[    5.359565] EXT4-fs (sdb1): orphan cleanup on readonly fs
[    5.513272] EXT4-fs (sdb1): 43 orphan inodes deleted
[    5.513274] EXT4-fs (sdb1): recovery complete
[    5.811511] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
[    6.920178] init: plymouth-upstart-bridge main process (250) terminated with status 1
[    6.920188] init: plymouth-upstart-bridge main process ended, respawning
[    6.922345] init: plymouth-upstart-bridge main process (261) terminated with status 1
[    6.922353] init: plymouth-upstart-bridge main process ended, respawning
[    6.923885] init: plymouth-upstart-bridge main process (263) terminated with status 1
[    6.923892] init: plymouth-upstart-bridge main process ended, respawning
[    6.925814] init: plymouth-upstart-bridge main process (264) terminated with status 1
[    6.925822] init: plymouth-upstart-bridge main process ended, respawning
[    6.927315] init: plymouth-upstart-bridge main process (266) terminated with status 1
[    6.927322] init: plymouth-upstart-bridge main process ended, respawning
[    6.929369] init: plymouth-upstart-bridge main process (267) terminated with status 1
[    6.929377] init: plymouth-upstart-bridge main process ended, respawning
[    6.930883] init: plymouth-upstart-bridge main process (269) terminated with status 1
[    6.930890] init: plymouth-upstart-bridge main process ended, respawning
[    6.932926] init: plymouth-upstart-bridge main process (270) terminated with status 1
[    6.932934] init: plymouth-upstart-bridge main process ended, respawning
[    6.934322] init: plymouth-upstart-bridge main process (272) terminated with status 1
[    6.934329] init: plymouth-upstart-bridge main process ended, respawning
[    6.936356] init: plymouth-upstart-bridge main process (273) terminated with status 1
[    6.936364] init: plymouth-upstart-bridge main process ended, respawning
[    6.937857] init: plymouth-upstart-bridge main process (275) terminated with status 1
[    6.937864] init: plymouth-upstart-bridge respawning too fast, stopped
[    8.856628] Adding 999420k swap on /dev/sdb3.  Priority:-1 extents:1 across:999420k FS
[    9.227627] systemd-udevd[379]: starting version 204
[   10.293579] lp: driver loaded but no devices found
[   10.299439] ppdev: user-space parallel port driver
[   12.186611] wmi: Mapper loaded
[   12.216436] MCE: In-kernel MCE decoding enabled.
[   12.240470] EDAC MC: Ver: 3.0.0
[   12.257511] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[   12.257559] piix4_smbus 0000:00:14.0: Auxiliary SMBus Host Controller at 0xb20
[   12.285750] AMD64 EDAC driver v3.4.0
[   12.285768] EDAC amd64: DRAM ECC disabled.
[   12.285779] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
[   12.285779]  Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
[   12.285779]  (Note that use of the override may cause unknown side effects.)
[   12.762486] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   13.082385] AVX version of gcm_enc/dec engaged.
[   13.179925] [drm] Initialized drm 1.1.0 20060810
[   13.399765] kvm: Nested Virtualization enabled
[   13.399771] kvm: Nested Paging enabled
[   13.511714] snd_hda_intel 0000:01:00.1: Handle VGA-switcheroo audio client
[   13.511717] snd_hda_intel 0000:01:00.1: Force to non-snoop mode
[   13.511813] snd_hda_intel 0000:01:00.1: irq 76 for MSI/MSI-X
[   13.548915] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input8
[   13.549143] input: HDA ATI HDMI HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input9
[   13.549460] input: HDA ATI HDMI HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input10
[   13.549843] input: HDA ATI HDMI HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input11
[   13.550301] input: HDA ATI HDMI HDMI/DP,pcm=10 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input12
[   13.553133] input: HDA ATI HDMI HDMI/DP,pcm=11 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input13
[   13.569731] sound hdaudioC0D0: autoconfig: line_outs=4 (0x14/0x15/0x16/0x17/0x0) type:line
[   13.569734] sound hdaudioC0D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   13.569736] sound hdaudioC0D0:    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[   13.569738] sound hdaudioC0D0:    mono: mono_out=0x0
[   13.569739] sound hdaudioC0D0:    dig-out=0x11/0x1e
[   13.569740] sound hdaudioC0D0:    inputs:
[   13.569742] sound hdaudioC0D0:      Front Mic=0x19
[   13.569744] sound hdaudioC0D0:      Rear Mic=0x18
[   13.569745] sound hdaudioC0D0:      Line=0x1a
[   13.573196] [drm] radeon kernel modesetting enabled.
[   13.573262] checking generic (c0000000 7f0000) vs hw (c0000000 10000000)
[   13.573264] fb: switching to radeondrmfb from VESA VGA
[   13.573301] Console: switching to colour dummy device 80x25
[   13.573637] [drm] initializing kernel modesetting (TAHITI 0x1002:0x6798 0x174B:0x3001).
[   13.573647] [drm] register mmio base: 0xFEA00000
[   13.573648] [drm] register mmio size: 262144
[   13.573697] ATOM BIOS: Tahiti
[   13.573739] [drm] Changing default dispclk from 500Mhz to 600Mhz
[   13.573754] radeon 0000:01:00.0: VRAM: 3072M 0x0000000000000000 - 0x00000000BFFFFFFF (3072M used)
[   13.573759] radeon 0000:01:00.0: GTT: 1024M 0x00000000C0000000 - 0x00000000FFFFFFFF
[   13.573760] [drm] Detected VRAM RAM=3072M, BAR=256M
[   13.573762] [drm] RAM width 384bits DDR
[   13.573814] [TTM] Zone  kernel: Available graphics memory: 4068166 kiB
[   13.573815] [TTM] Zone   dma32: Available graphics memory: 2097152 kiB
[   13.573816] [TTM] Initializing pool allocator
[   13.573821] [TTM] Initializing DMA pool allocator
[   13.573838] [drm] radeon: 3072M of VRAM memory ready
[   13.573839] [drm] radeon: 1024M of GTT memory ready.
[   13.573850] [drm] Loading TAHITI Microcode
[   13.584383] input: HDA ATI SB Front Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input14
[   13.585629] input: HDA ATI SB Rear Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input15
[   13.585953] input: HDA ATI SB Line as /devices/pci0000:00/0000:00:14.2/sound/card0/input16
[   13.586032] input: HDA ATI SB Line Out Front as /devices/pci0000:00/0000:00:14.2/sound/card0/input17
[   13.586174] input: HDA ATI SB Line Out Surround as /devices/pci0000:00/0000:00:14.2/sound/card0/input18
[   13.586512] input: HDA ATI SB Line Out CLFE as /devices/pci0000:00/0000:00:14.2/sound/card0/input19
[   13.586863] input: HDA ATI SB Line Out Side as /devices/pci0000:00/0000:00:14.2/sound/card0/input20
[   13.586938] input: HDA ATI SB Front Headphone as /devices/pci0000:00/0000:00:14.2/sound/card0/input21
[   13.915580] [drm] radeon/TAHITI_mc2.bin: 31232 bytes
[   13.915743] usb 11-1: reset SuperSpeed USB device number 2 using xhci_hcd
[   13.931884] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff8802333f3c00
[   13.931887] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff8802333f3c48
[   13.979001] audit: type=1400 audit(1432340963.027:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/sbin/dhclient" pid=500 comm="apparmor_parser"
[   13.979006] audit: type=1400 audit(1432340963.027:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=500 comm="apparmor_parser"
[   13.979010] audit: type=1400 audit(1432340963.027:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=500 comm="apparmor_parser"
[   13.979022] audit: type=1400 audit(1432340963.027:5): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/sbin/dhclient" pid=464 comm="apparmor_parser"
[   13.979028] audit: type=1400 audit(1432340963.027:6): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=464 comm="apparmor_parser"
[   13.979033] audit: type=1400 audit(1432340963.027:7): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=464 comm="apparmor_parser"
[   13.979328] audit: type=1400 audit(1432340963.027:8): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=500 comm="apparmor_parser"
[   13.979334] audit: type=1400 audit(1432340963.027:9): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=500 comm="apparmor_parser"
[   13.979341] audit: type=1400 audit(1432340963.027:10): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=464 comm="apparmor_parser"
[   13.979345] audit: type=1400 audit(1432340963.027:11): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=464 comm="apparmor_parser"
[   13.990351] [drm] Internal thermal controller with fan control
[   13.990522] [drm] probing gen 2 caps for device 1002:5a16 = 31cd02/0
[   13.995786] [drm] radeon: dpm initialized
[   14.108678] [drm] GART: num cpu pages 262144, num gpu pages 262144
[   14.109660] [drm] probing gen 2 caps for device 1002:5a16 = 31cd02/0
[   14.109663] [drm] PCIE gen 2 link speeds already enabled
[   14.126695] [drm] PCIE GART of 1024M enabled (table at 0x0000000000276000).
[   14.126802] radeon 0000:01:00.0: WB enabled
[   14.126805] radeon 0000:01:00.0: fence driver on ring 0 use gpu addr 0x00000000c0000c00 and cpu addr 0xffff880231e2fc00
[   14.126807] radeon 0000:01:00.0: fence driver on ring 1 use gpu addr 0x00000000c0000c04 and cpu addr 0xffff880231e2fc04
[   14.126809] radeon 0000:01:00.0: fence driver on ring 2 use gpu addr 0x00000000c0000c08 and cpu addr 0xffff880231e2fc08
[   14.126810] radeon 0000:01:00.0: fence driver on ring 3 use gpu addr 0x00000000c0000c0c and cpu addr 0xffff880231e2fc0c
[   14.126812] radeon 0000:01:00.0: fence driver on ring 4 use gpu addr 0x00000000c0000c10 and cpu addr 0xffff880231e2fc10
[   14.127207] radeon 0000:01:00.0: fence driver on ring 5 use gpu addr 0x0000000000075a18 and cpu addr 0xffffc90011eb5a18
[   14.127209] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[   14.127210] [drm] Driver supports precise vblank timestamp query.
[   14.127211] radeon 0000:01:00.0: radeon: MSI limited to 32-bit
[   14.127231] radeon 0000:01:00.0: irq 77 for MSI/MSI-X
[   14.127241] radeon 0000:01:00.0: radeon: using MSI.
[   14.127260] [drm] radeon: irq initialized.
[   14.291813] [drm] ring test on 0 succeeded in 1 usecs
[   14.291818] [drm] ring test on 1 succeeded in 1 usecs
[   14.291822] [drm] ring test on 2 succeeded in 1 usecs
[   14.291829] [drm] ring test on 3 succeeded in 3 usecs
[   14.291834] [drm] ring test on 4 succeeded in 3 usecs
[   14.487226] [drm] ring test on 5 succeeded in 2 usecs
[   14.487231] [drm] UVD initialized successfully.
[   14.487548] [drm] ib test on ring 0 succeeded in 0 usecs
[   14.487567] [drm] ib test on ring 1 succeeded in 0 usecs
[   14.487585] [drm] ib test on ring 2 succeeded in 0 usecs
[   14.487603] [drm] ib test on ring 3 succeeded in 0 usecs
[   14.487620] [drm] ib test on ring 4 succeeded in 0 usecs
[   14.657842] [drm] ib test on ring 5 succeeded
[   14.658770] [drm] Radeon Display Connectors
[   14.658772] [drm] Connector 0:
[   14.658773] [drm]   DP-1
[   14.658774] [drm]   HPD5
[   14.658775] [drm]   DDC: 0x6530 0x6530 0x6534 0x6534 0x6538 0x6538 0x653c 0x653c
[   14.658776] [drm]   Encoders:
[   14.658777] [drm]     DFP1: INTERNAL_UNIPHY2
[   14.658778] [drm] Connector 1:
[   14.658779] [drm]   HDMI-A-1
[   14.658779] [drm]   HPD4
[   14.658781] [drm]   DDC: 0x6540 0x6540 0x6544 0x6544 0x6548 0x6548 0x654c 0x654c
[   14.658781] [drm]   Encoders:
[   14.658782] [drm]     DFP2: INTERNAL_UNIPHY2
[   14.658783] [drm] Connector 2:
[   14.658784] [drm]   DVI-D-1
[   14.658785] [drm]   HPD1
[   14.658786] [drm]   DDC: 0x6550 0x6550 0x6554 0x6554 0x6558 0x6558 0x655c 0x655c
[   14.658787] [drm]   Encoders:
[   14.658787] [drm]     DFP3: INTERNAL_UNIPHY1
[   14.658788] [drm] Connector 3:
[   14.658789] [drm]   DVI-I-1
[   14.658790] [drm]   HPD3
[   14.658791] [drm]   DDC: 0x6580 0x6580 0x6584 0x6584 0x6588 0x6588 0x658c 0x658c
[   14.658792] [drm]   Encoders:
[   14.658793] [drm]     DFP4: INTERNAL_UNIPHY
[   14.658793] [drm]     CRT1: INTERNAL_KLDSCP_DAC1
[   14.744806] [drm] fb mappable at 0xC0478000
[   14.744808] [drm] vram apper at 0xC0000000
[   14.744809] [drm] size 8294400
[   14.744810] [drm] fb depth is 24
[   14.744811] [drm]    pitch is 7680
[   14.744943] fbcon: radeondrmfb (fb0) is primary device
[   14.745030] Console: switching to colour frame buffer device 240x67
[   14.745059] radeon 0000:01:00.0: fb0: radeondrmfb frame buffer device
[   14.745060] radeon 0000:01:00.0: registered panic notifier
[   14.750880] [drm] Initialized radeon 2.39.0 20080528 for 0000:01:00.0 on minor 0
[   16.105178] EXT4-fs (sdb1): re-mounted. Opts: errors=remount-ro
[   25.394446] EXT4-fs (sdb2): mounted filesystem with ordered data mode. Opts: (null)
[   25.511449] init: failsafe main process (746) killed by TERM signal
[   26.469642] audit_printk_skb: 6 callbacks suppressed
[   26.469645] audit: type=1400 audit(1432340975.527:14): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/sbin/dhclient" pid=873 comm="apparmor_parser"
[   26.469652] audit: type=1400 audit(1432340975.527:15): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=873 comm="apparmor_parser"
[   26.469656] audit: type=1400 audit(1432340975.527:16): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=873 comm="apparmor_parser"
[   26.470000] audit: type=1400 audit(1432340975.527:17): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=873 comm="apparmor_parser"
[   26.470004] audit: type=1400 audit(1432340975.527:18): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=873 comm="apparmor_parser"
[   26.470172] audit: type=1400 audit(1432340975.527:19): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=873 comm="apparmor_parser"
[   26.573799] audit: type=1400 audit(1432340975.631:20): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/cups-browsed" pid=877 comm="apparmor_parser"
[   26.597665] audit: type=1400 audit(1432340975.655:21): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/cups/backend/cups-pdf" pid=878 comm="apparmor_parser"
[   26.597670] audit: type=1400 audit(1432340975.655:22): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/cupsd" pid=878 comm="apparmor_parser"
[   26.597935] audit: type=1400 audit(1432340975.655:23): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=878 comm="apparmor_parser"

Si quelqu'un a une idée de la source je suis preneur ^^ (j'ai sur le pc un autre hdd plus récent et plus rapide mais vu que Windows est dessus je me disais que c'était dommage de tout modifier pour mettre les deux systemes sur le rapide car je pensais que Ubuntu serait assez rapide sur ce disque, mais dans tous les cas je peux le faire quand même ^^)

/!\ PS: J'ai oublié de préciser mais pendant tout le boot j'ai un écran noir (en fait j'ai l'impression que y'a pas d'image envoyé à l'écran du tout car il me fait la même chose que quand il est allumé mais que le pc est éteint)

Merci d'avance !

Dernière modification par Azka (Le 23/05/2015, à 03:02)

moko138

Re : Boot relativement lent.

1) ton dmesg est coupé au début et à la fin. Redémarre et sitôt arrivé sur le bureau, fais

dmesg>dmesg_2015-05-24.txt

puis colle tout ce fichier ici.

2) Donne aussi

sudo parted -l

sudo fdisk -l

sudo blkid

cat /etc/fstab

cat /etc/default/grub

Dernière modification par moko138 (Le 24/05/2015, à 05:18)

---

%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel :  À la découverte de dcraw