Pages : 1
#1 Le 07/06/2015, à 22:07
- white_mike
[Solved]Erreur smart
Bonsoir,
J'ai un petit raid 5 de 3 disques de 2To chez moi qui me servent pour le stockage.
Aucun soucis jusque mercredi soir où j'ai reçu un mail me disant qu'une erreur a été rencontrée. J'ai donc lancé un smartctl -a /dev/sdX ainsi qu'un smartctl -t long /dev/sdX (sur le même volume)
smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.2.0-4-amd64] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net=== START OF INFORMATION SECTION ===
Model Family: Western Digital Green
Device Model: WDC WD20EZRX-00D8PB0
Serial Number: WD-WCC4M0108509
LU WWN Device Id: 5 0014ee 2090e1e2e
Firmware Version: 80.00A80
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 9
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sun Jun 7 21:56:28 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSEDGeneral SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 241) Self-test routine in progress...
10% of test remaining.
Total time to complete Offline
data collection: (26460) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 255) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x7035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 173 170 021 Pre-fail Always - 4316
4 Start_Stop_Count 0x0032 088 088 000 Old_age Always - 12034
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 083 083 000 Old_age Always - 12422
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 39
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 22
193 Load_Cycle_Count 0x0032 196 196 000 Old_age Always - 12050
194 Temperature_Celsius 0x0022 103 100 000 Old_age Always - 44
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0SMART Error Log Version: 1
ATA Error Count: 1
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.Error 1 occurred at disk power-on lifetime: 12332 hours (513 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 01 00 00 00 00 Error: ABRTCommands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 d5 01 e1 4f c2 00 08 07:43:17.258 SMART READ LOG
b0 d5 01 e1 4f c2 00 08 07:43:17.258 SMART READ LOG
b0 d6 01 e0 4f c2 00 08 07:43:17.257 SMART WRITE LOG
b0 d6 01 e0 4f c2 00 08 07:43:17.256 SMART WRITE LOG
b0 d5 01 e0 4f c2 00 08 07:43:17.256 SMART READ LOGSMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 12366 -
# 2 Extended offline Completed without error 00% 11895 -
# 3 Extended offline Completed without error 00% 11181 -
# 4 Extended offline Completed without error 00% 10439 -
# 5 Extended offline Completed without error 00% 9770 -
# 6 Extended offline Completed without error 00% 9428 -
# 7 Extended offline Completed without error 00% 8686 -
# 8 Short offline Completed without error 00% 8245 -SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Depuis je n'ai plus rien reçu comme alerte.
J'ai ramené un disque dur de 2To que je voulais ajouter pour gonfler ce raid mais là j'hésite à l'utiliser en remplacement de ce disque pour éviter toute mauvaise surprise !
Par contre ce serait plus un WD Green de 2To mais un Seagate 2To hors mis une éventuelle baisse de perf en transfert (j'ai des doutes le seagate est plus performant mais va se caler sur les autres) pas de risques particulier ? Raid software via mdadm.
Merci de votre aide !
Dernière modification par white_mike (Le 25/06/2015, à 14:48)
Hors ligne
#2 Le 08/06/2015, à 10:54
- white_mike
Re : [Solved]Erreur smart
Pas de "pro" pour me donner son avis sur ce retour SMART ?
Hors ligne
#3 Le 08/06/2015, à 22:28
- alca94
Re : [Solved]Erreur smart
Bonsoir
Je ne saurais vous aider mais vous dîtes
Par contre ce serait plus un WD Green de 2To mais un Seagate 2To
Par contre je sais qu'il y a des problèmes avec ces disques WD "green" voir ce post
https://forum.ubuntu-fr.org/viewtopic.php?id=403064
POUR METTRE LES RETOURS DU "TERMINAL" voir les explications sur ce post
https://forum.ubuntu-fr.org/viewtopic.p … #p17345641
Hors ligne
#4 Le 23/06/2015, à 11:08
- white_mike
Re : [Solved]Erreur smart
En faite je voulais dire que j'avais un disque de réserve mais qui n'était pas un WD Green mais un Seagate de 2To lui aussi.
Je ne vois plus aucune erreur smart remontée. Je remplace le disque malgré tout ? Ou je peux étendre mon Raid ?
Hors ligne
#5 Le 25/06/2015, à 14:47
- white_mike
Re : [Solved]Erreur smart
J'ai étendu le raid et je n'ai pas de soucis pour le moment.
Merci !
Hors ligne
Pages : 1