Pages : 1
#1 Le 26/02/2019, à 22:22
- bbenn
[Résolu] Couldn't get UEFI db list
Hors ligne
#2 Le 26/02/2019, à 23:17
- Nuliel
Re : [Résolu] Couldn't get UEFI db list
Le secure boot est il activé dans le bios? Si oui, désactive le et réessaie
Merci de faire des miniatures cliquables à l'avenir
Dernière modification par Nuliel (Le 26/02/2019, à 23:19)
Hors ligne
#3 Le 26/02/2019, à 23:39
- bbenn
Re : [Résolu] Couldn't get UEFI db list
je ne vois rien concernant le secure boot dans le bios
c'est cette carte mère:
https://www.asus.com/fr/Motherboards/P8P67/
pour le coup de la miniature cliquable je veux bien mais toutefois je trouve que c'était mieux comme j'avais fait
Hors ligne
#4 Le 27/02/2019, à 00:05
- Nuliel
Re : [Résolu] Couldn't get UEFI db list
C'est une usine à gaz ton bios!
As tu accès au menu grub? Si oui peux tu tenter d'aller dans options avancées pour démarrer sur le plus vieux noyau sans upstart ni recovery?
PS: le principe de la miniature cliquable, c'est de permettre d'éviter d'utiliser trop de bande passante pour ceux qui en ont peu. Mais j'ai vu que tu avais pas mis la grande photo
Hors ligne
#5 Le 27/02/2019, à 00:12
- bbenn
Re : [Résolu] Couldn't get UEFI db list
bah ouais j'avais pas mis la grande elle faisait 86ko (et puis il faut bien cliquer dessus pour pouvoir lire donc au final ça consomme encore plus )
bref j'ai fais un fsck de mon fs et c'est résolu pour l'instant
Hors ligne
#6 Le 27/02/2019, à 00:15
- Nuliel
Re : [Résolu] Couldn't get UEFI db list
bref j'ai fais un fsck de mon fs et c'est résolu pour l'instant
Mais ça n'a aucun rapport! Mais content que ça marche.
Tu peux faire un rapport smart:
sudo apt-get install --no-install-recommends smartmontools
sudo smartctl --smart=on --offlineauto=on --saveauto=on /dev/sda
sudo smartctl -s on -a /dev/sda
Hors ligne
#7 Le 27/02/2019, à 00:20
- bbenn
Re : [Résolu] Couldn't get UEFI db list
sudo smartctl -s on -a /dev/sda5
[sudo] Mot de passe de bbenn :
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.15.0-43-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Samsung based SSDs
Device Model: Samsung SSD 840 PRO Series
Serial Number: S12PNEAD103438B
LU WWN Device Id: 5 002538 55016f28d
Firmware Version: DXM04B0Q
User Capacity: 128035676160 bytes [128 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Tue Feb 26 23:16:50 2019 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (65476) seconds.
Offline data collection
capabilities: (0x53) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 15) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
9 Power_On_Hours 0x0032 097 097 000 Old_age Always - 13740
12 Power_Cycle_Count 0x0032 095 095 000 Old_age Always - 4718
177 Wear_Leveling_Count 0x0013 096 096 000 Pre-fail Always - 143
179 Used_Rsvd_Blk_Cnt_Tot 0x0013 100 100 010 Pre-fail Always - 0
181 Program_Fail_Cnt_Total 0x0032 100 100 010 Old_age Always - 0
182 Erase_Fail_Count_Total 0x0032 100 100 010 Old_age Always - 0
183 Runtime_Bad_Block 0x0013 100 100 010 Pre-fail Always - 0
187 Uncorrectable_Error_Cnt 0x0032 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0032 076 051 000 Old_age Always - 24
195 ECC_Error_Rate 0x001a 200 200 000 Old_age Always - 0
199 CRC_Error_Count 0x003e 099 099 000 Old_age Always - 2
235 POR_Recovery_Count 0x0012 099 099 000 Old_age Always - 1182
241 Total_LBAs_Written 0x0032 099 099 000 Old_age Always - 12891952208
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
255 0 65535 Read_scanning was never started
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Hors ligne
#8 Le 27/02/2019, à 00:35
- bbenn
Re : [Résolu] Couldn't get UEFI db list
je viens de faire un apt-get update et ça me dit ça à la fin:
This system doesn't support Secure Boot
Secure Boot not enabled on this system.
Hors ligne
#9 Le 27/02/2019, à 07:13
- Nuliel
Re : [Résolu] Couldn't get UEFI db list
Hum, bizarre! Le disque a l'air en bon état.
Hors ligne
Pages : 1