#1 Le 22/06/2008, à 09:14
- Calimo
[Résolu] Erreurs Emask, kernel panic, disque lent...
Salut,
Hier mon Ubuntu (Hardy, mis à jour depuis gusty par le système de mise à jour automatiques) n'a pas démarré et est resté "planté" sur "Reading files needed to boot". Ce n'est pas la première fois, cf par exemple http://forum.ubuntu-fr.org/viewtopic.php?pid=1562664#p1562664 et http://forum.ubuntu-fr.org/viewtopic.php?id=205852
Je passe par la liveCD, je checke / (sdb1) et /home (sdb6), redémarre, et tout passe très bien.
J'avais fais des tests "SMART" sans rien trouver d'anormal il y a quelques temps...
Ce matin, je le laisse démarrer, et en revenant, j'ai une console initramfs (ou quelque chose comme ça). Je fais help puis reboot et au démarrage suivant, j'ai à nouveau des erreurs emask et là un joli kernel panic. Alt+SysRQ+REISUB n'a pas permi de "débloquer" la situation, donc reset avec le bouton de façade.
Je démarre en liveCD et lance une réinstallation du système. Je choisi de formatter sdb1 (/) et de reprendre sdb6 (/home) sans formatter. Je lance l'installation, et là il se plante à 15% sur une étape que j'ai "bêtement" oublié de noter, mais qui est juste après avoir cliqué sur ce bouton "installer" : http://doc.ubuntu-fr.org/lib/exe/fetch.php?cache=cache&media=http%3A%2F%2Fyeknan.free.fr%2Fblog%2Fimages%2Fubuntu7.10%2Finstall%2F19.png (Initialisation du partitionnement/formatage). J'ai bien laissé 30 minutes avant de redémarrer.
Donc je redémarre (sans liveCD), et là ça passe (heureusement il n'a pas formatté), mais c'est extrêmement lent !
xavier@ubuntu:~$ sudo hdparm -t /dev/sdb1
/dev/sdb1:
Timing buffered disk reads: 22 MB in 4.24 seconds = 5.19 MB/sec
xavier@ubuntu:~$ sudo hdparm -t /dev/sdb6
/dev/sdb6:
Timing buffered disk reads: 62 MB in 5.43 seconds = 11.42 MB/secPour comparaison, sda1 (même disque mais avec une capacité différente) :
xavier@ubuntu:~$ sudo hdparm -t /dev/sda1
/dev/sda1:
Timing buffered disk reads: 176 MB in 3.02 seconds = 58.20 MB/secce qui s'approche de ce que j'ai normalement pour sdb.
Bref, j'ai un problème quelque part avec mon disque, mais je suis incapable de savoir quoi.
Qu'est-ce que je peux faire pour retrouver un Ubuntu "stable", qui démarre rapidement ? Quels diagnostics est-ce que je peux faire ? Mon disque est récent (1 an et 1 mois).
Merci d'avance pour votre aide, 
Calimo
À toutes fins utiles, voici le rapport de dmesg :
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.24-19-generic (buildd@palmer) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP Wed Jun 18 14:43:41 UTC 2008 (Ubuntu 2.6.24-19.34-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003ffc0000 (usable)
[ 0.000000] BIOS-e820: 000000003ffc0000 - 000000003ffce000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003ffce000 - 000000003fff0000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
[ 0.000000] 127MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000ff780
[ 0.000000] Entering add_active_range(0, 0, 262080) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 262080
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 262080
[ 0.000000] On node 0 totalpages: 262080
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 255 pages used for memmap
[ 0.000000] HighMem zone: 32449 pages, LIFO batch:7
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP signature @ 0xC00FBA80 checksum 0
[ 0.000000] ACPI: RSDP 000FBA80, 0014 (r0 ACPIAM)
[ 0.000000] ACPI: RSDT 3FFC0000, 0038 (r1 A M I OEMRSDT 8000622 MSFT 97)
[ 0.000000] ACPI: FACP 3FFC0200, 0084 (r2 A M I OEMFACP 8000622 MSFT 97)
[ 0.000000] ACPI: DSDT 3FFC0440, 54B5 (r1 A0627 A0627000 0 INTL 2002026)
[ 0.000000] ACPI: FACS 3FFCE000, 0040
[ 0.000000] ACPI: APIC 3FFC0390, 0070 (r1 A M I OEMAPIC 8000622 MSFT 97)
[ 0.000000] ACPI: MCFG 3FFC0400, 003C (r1 A M I OEMMCFG 8000622 MSFT 97)
[ 0.000000] ACPI: OEMB 3FFCE040, 0060 (r1 A M I AMI_OEM 8000622 MSFT 97)
[ 0.000000] ACPI: SSDT 3FFC5900, 01C4 (r1 A M I POWERNOW 1 AMD 1)
[ 0.000000] Nvidia board detected. Ignoring ACPI timer override.
[ 0.000000] If you got timer trouble try acpi_use_timer_override
[ 0.000000] ACPI: PM-Timer IO Port: 0x508
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:11 APIC version 16
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] Processor #1 15:11 APIC version 16
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 0 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] ACPI: IRQ14 used by override.
[ 0.000000] ACPI: IRQ15 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
[ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000e0000 - 0000000000100000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260033
[ 0.000000] Kernel command line: root=UUID=55c09940-8ec2-42b1-beb9-a8cad49917a1 ro splash locale=fr_FR
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 2009.158 MHz processor.
[ 15.252649] spurious 8259A interrupt: IRQ7.
[ 15.255006] Console: colour VGA+ 80x25
[ 15.255009] console [tty0] enabled
[ 15.259207] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 15.259646] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 15.281846] Memory: 1026296k/1048320k available (2177k kernel code, 21308k reserved, 1006k data, 368k init, 130816k highmem)
[ 15.281933] virtual kernel memory layout:
[ 15.281934] fixmap : 0xfff4b000 - 0xfffff000 ( 720 kB)
[ 15.281935] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 15.281936] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 15.281937] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 15.281938] .init : 0xc0421000 - 0xc047d000 ( 368 kB)
[ 15.281939] .data : 0xc0320434 - 0xc041bdc4 (1006 kB)
[ 15.281940] .text : 0xc0100000 - 0xc0320434 (2177 kB)
[ 15.282441] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 15.282596] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
[ 15.362596] Calibrating delay using timer specific routine.. 4022.53 BogoMIPS (lpj=8045071)
[ 15.362742] Security Framework initialized
[ 15.362808] SELinux: Disabled at boot.
[ 15.362882] AppArmor: AppArmor initialized
[ 15.362946] Failure registering capabilities with primary security module.
[ 15.363018] Mount-cache hash table entries: 512
[ 15.363181] Initializing cgroup subsys ns
[ 15.363246] Initializing cgroup subsys cpuacct
[ 15.363316] CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000001f 00000000
[ 15.363324] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 15.363390] CPU: L2 Cache: 512K (64 bytes/line)
[ 15.363454] CPU 0(2) -> Core 0
[ 15.363516] CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000001f 00000000
[ 15.363525] Compat vDSO mapped to ffffe000.
[ 15.363596] Checking 'hlt' instruction... OK.
[ 15.378896] SMP alternatives: switching to UP code
[ 15.380087] Early unpacking initramfs... done
[ 15.715265] ACPI: Core revision 20070126
[ 15.715379] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 15.717975] CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02
[ 15.718162] SMP alternatives: switching to SMP code
[ 15.718668] Booting processor 1/1 eip 3000
[ 15.728237] Initializing CPU#1
[ 15.805559] Calibrating delay using timer specific routine.. 3987.12 BogoMIPS (lpj=7974246)
[ 15.805565] CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000001f 00000000
[ 15.805572] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 15.805574] CPU: L2 Cache: 512K (64 bytes/line)
[ 15.805576] CPU 1(2) -> Core 1
[ 15.805577] CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000001f 00000000
[ 15.806230] CPU1: AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02
[ 15.806723] Total of 2 processors activated (8009.65 BogoMIPS).
[ 15.807020] ENABLING IO-APIC IRQs
[ 15.807316] ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
[ 15.953957] Brought up 2 CPUs
[ 15.954064] CPU0 attaching sched-domain:
[ 15.954067] domain 0: span 03
[ 15.954069] groups: 01 02
[ 15.954072] CPU1 attaching sched-domain:
[ 15.954073] domain 0: span 03
[ 15.954075] groups: 02 01
[ 15.954258] net_namespace: 64 bytes
[ 15.954325] Booting paravirtualized kernel on bare hardware
[ 15.954817] Time: 7:35:09 Date: 06/22/08
[ 15.954901] NET: Registered protocol family 16
[ 15.955124] EISA bus registered
[ 15.955188] ACPI: bus type pci registered
[ 15.955908] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=4
[ 15.955974] PCI: Using configuration type 1
[ 15.956043] Setting up standard PCI resources
[ 15.963516] ACPI: EC: Look up EC in DSDT
[ 15.968532] ACPI: Interpreter enabled
[ 15.968596] ACPI: (supports S0 S1 S3 S4 S5)
[ 15.968907] ACPI: Using IOAPIC for interrupt routing
[ 15.977964] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 15.978652] PCI: Transparent bridge - 0000:00:04.0
[ 15.978915] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 15.979112] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 15.979240] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
[ 15.979327] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR11._PRT]
[ 15.979413] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR12._PRT]
[ 15.986471] ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *0, disabled.
[ 15.987114] ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *0, disabled.
[ 15.987753] ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *0, disabled.
[ 15.988390] ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled.
[ 15.989028] ACPI: PCI Interrupt Link [LNEA] (IRQs 16 17 18 19) *0, disabled.
[ 15.989665] ACPI: PCI Interrupt Link [LNEB] (IRQs 16 17 18 19) *0, disabled.
[ 15.990564] ACPI: PCI Interrupt Link [LNEC] (IRQs 16 17 18 19) *0, disabled.
[ 15.991201] ACPI: PCI Interrupt Link [LNED] (IRQs 16 17 18 19) *11
[ 15.991791] ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *11
[ 15.992381] ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *10
[ 15.992970] ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *11
[ 15.993559] ACPI: PCI Interrupt Link [LAZA] (IRQs 20 21 22 23) *11
[ 15.994167] ACPI: PCI Interrupt Link [LACI] (IRQs 20 21 22 23) *0, disabled.
[ 15.994807] ACPI: PCI Interrupt Link [LMC9] (IRQs 20 21 22 23) *0, disabled.
[ 15.995445] ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *10
[ 15.996037] ACPI: PCI Interrupt Link [LPMU] (IRQs 20 21 22 23) *0, disabled.
[ 15.996676] ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *15
[ 15.997267] ACPI: PCI Interrupt Link [LSA1] (IRQs 20 21 22 23) *5
[ 15.997901] ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0, disabled.
[ 15.998453] ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - 22, should be 15 [20070126]
[ 15.998631] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 15.998719] pnp: PnP ACPI init
[ 15.998785] ACPI: bus type pnp registered
[ 16.004914] pnp: PnP ACPI: found 14 devices
[ 16.004977] ACPI: ACPI bus type pnp unregistered
[ 16.005041] PnPBIOS: Disabled by ACPI PNP
[ 16.005287] PCI: Using ACPI for IRQ routing
[ 16.005352] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 16.025774] NET: Registered protocol family 8
[ 16.025837] NET: Registered protocol family 20
[ 16.025958] AppArmor: AppArmor Filesystem Enabled
[ 16.037785] system 00:07: ioport range 0x4d0-0x4d1 has been reserved
[ 16.037852] system 00:07: ioport range 0x800-0x80f has been reserved
[ 16.037917] system 00:07: ioport range 0x500-0x57f has been reserved
[ 16.037983] system 00:07: ioport range 0x580-0x5ff has been reserved
[ 16.038049] system 00:07: ioport range 0x800-0x87f could not be reserved
[ 16.038115] system 00:07: ioport range 0x880-0x8ff has been reserved
[ 16.038180] system 00:07: ioport range 0xd00-0xd7f has been reserved
[ 16.038246] system 00:07: ioport range 0xd80-0xdff has been reserved
[ 16.038312] system 00:07: ioport range 0x2000-0x207f has been reserved
[ 16.038378] system 00:07: ioport range 0x2080-0x20ff has been reserved
[ 16.038444] system 00:07: iomem range 0x0-0x0 could not be reserved
[ 16.038510] system 00:07: iomem range 0xfefe0000-0xfefe01ff has been reserved
[ 16.038576] system 00:07: iomem range 0xfefe1000-0xfefe1fff has been reserved
[ 16.038644] system 00:07: iomem range 0xfee01000-0xfeefffff could not be reserved
[ 16.038720] system 00:07: iomem range 0xffb80000-0xffffffff could not be reserved
[ 16.038800] system 00:08: iomem range 0xfec00000-0xfec00fff could not be reserved
[ 16.038876] system 00:08: iomem range 0xfee00000-0xfee00fff could not be reserved
[ 16.038956] system 00:0a: ioport range 0x230-0x23f has been reserved
[ 16.039021] system 00:0a: ioport range 0x290-0x29f has been reserved
[ 16.039087] system 00:0a: ioport range 0xa00-0xa0f has been reserved
[ 16.039153] system 00:0a: ioport range 0xa10-0xa1f has been reserved
[ 16.039222] system 00:0c: iomem range 0xe0000000-0xefffffff has been reserved
[ 16.039292] system 00:0d: iomem range 0x0-0x9ffff could not be reserved
[ 16.039358] system 00:0d: iomem range 0xc0000-0xcffff could not be reserved
[ 16.039425] system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
[ 16.041061] system 00:0d: iomem range 0x100000-0x3fffffff could not be reserved
[ 16.041137] system 00:0d: iomem range 0xff780000-0xffffffff could not be reserved
[ 16.071525] PCI: Bridge: 0000:00:04.0
[ 16.071588] IO window: disabled.
[ 16.071651] MEM window: disabled.
[ 16.071714] PREFETCH window: disabled.
[ 16.071777] PCI: Bridge: 0000:00:09.0
[ 16.071839] IO window: disabled.
[ 16.071901] MEM window: ddf00000-dfffffff
[ 16.071964] PREFETCH window: c0000000-cfffffff
[ 16.072027] PCI: Bridge: 0000:00:0b.0
[ 16.072088] IO window: disabled.
[ 16.072150] MEM window: disabled.
[ 16.072212] PREFETCH window: disabled.
[ 16.072275] PCI: Bridge: 0000:00:0c.0
[ 16.072336] IO window: disabled.
[ 16.072398] MEM window: disabled.
[ 16.072460] PREFETCH window: disabled.
[ 16.072530] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 16.072539] PCI: Setting latency timer of device 0000:00:09.0 to 64
[ 16.072545] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[ 16.072551] PCI: Setting latency timer of device 0000:00:0c.0 to 64
[ 16.072560] NET: Registered protocol family 2
[ 16.073706] Time: acpi_pm clocksource has been installed.
[ 16.073785] Switched to high resolution mode on CPU 0
[ 16.073326] Switched to high resolution mode on CPU 1
[ 16.109693] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 16.110020] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 16.110837] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 16.111295] TCP: Hash tables configured (established 131072 bind 65536)
[ 16.111361] TCP reno registered
[ 16.121738] checking if image is initramfs... it is
[ 16.768712] Freeing initrd memory: 8136k freed
[ 16.769039] audit: initializing netlink socket (disabled)
[ 16.769117] audit(1214120109.388:1): initialized
[ 16.769328] highmem bounce pool size: 64 pages
[ 16.771121] VFS: Disk quotas dquot_6.5.1
[ 16.771248] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 16.771422] io scheduler noop registered
[ 16.771485] io scheduler anticipatory registered
[ 16.771548] io scheduler deadline registered
[ 16.771618] io scheduler cfq registered (default)
[ 16.771708] pci 0000:00:00.0: Enabling HT MSI Mapping
[ 17.295396] pci 0000:00:04.0: Enabling HT MSI Mapping
[ 17.295473] pci 0000:00:05.0: Enabling HT MSI Mapping
[ 17.295562] pci 0000:00:07.0: Enabling HT MSI Mapping
[ 17.295636] pci 0000:00:08.0: Enabling HT MSI Mapping
[ 17.295711] pci 0000:00:08.1: Enabling HT MSI Mapping
[ 17.295786] pci 0000:00:09.0: Enabling HT MSI Mapping
[ 17.295861] pci 0000:00:0b.0: Enabling HT MSI Mapping
[ 17.295937] pci 0000:00:0c.0: Enabling HT MSI Mapping
[ 17.296017] Boot video device is 0000:02:00.0
[ 17.296112] PCI: Setting latency timer of device 0000:00:09.0 to 64
[ 17.296133] assign_interrupt_mode Found MSI capability
[ 17.296212] Allocate Port Service[0000:00:09.0:pcie00]
[ 17.296269] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[ 17.296289] assign_interrupt_mode Found MSI capability
[ 17.296365] Allocate Port Service[0000:00:0b.0:pcie00]
[ 17.296418] PCI: Setting latency timer of device 0000:00:0c.0 to 64
[ 17.296437] assign_interrupt_mode Found MSI capability
[ 17.296521] Allocate Port Service[0000:00:0c.0:pcie00]
[ 17.296730] isapnp: Scanning for PnP cards...
[ 17.647024] isapnp: No Plug & Play device found
[ 17.672818] Real Time Clock Driver v1.12ac
[ 17.672979] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 17.673165] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 17.673767] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 17.674542] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 17.674677] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 17.674835] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 17.674901] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 17.675280] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 17.692018] mice: PS/2 mouse device common for all mice
[ 17.692195] EISA: Probing bus 0 at eisa.0
[ 17.692265] Cannot allocate resource for EISA slot 2
[ 17.692343] EISA: Detected 0 cards.
[ 17.692406] cpuidle: using governor ladder
[ 17.692469] cpuidle: using governor menu
[ 17.692608] NET: Registered protocol family 1
[ 17.692689] Using IPI No-Shortcut mode
[ 17.692779] registered taskstats version 1
[ 17.692944] Magic number: 12:422:572
[ 17.693061] hash matches device ptyb4
[ 17.693202] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 17.693267] EDD information not available.
[ 17.693556] Freeing unused kernel memory: 368k freed
[ 18.990283] fuse init (API version 7.9)
[ 19.029153] device-mapper: uevent: version 1.0.3
[ 19.029195] device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com
[ 19.493797] usbcore: registered new interface driver usbfs
[ 19.493819] usbcore: registered new interface driver hub
[ 19.503178] usbcore: registered new device driver usb
[ 19.512996] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 19.514427] ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 23
[ 19.514438] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUB0] -> GSI 23 (level, low) -> IRQ 16
[ 19.514448] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 19.514451] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 19.514683] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
[ 19.514698] ohci_hcd 0000:00:02.0: irq 16, io mem 0xddeff000
[ 19.545133] SCSI subsystem initialized
[ 19.570964] usb usb1: configuration #1 chosen from 1 choice
[ 19.570986] hub 1-0:1.0: USB hub found
[ 19.570994] hub 1-0:1.0: 10 ports detected
[ 19.571642] libata version 3.00 loaded.
[ 19.672318] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61.
[ 19.672648] ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 22
[ 19.672657] ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [LMAC] -> GSI 22 (level, low) -> IRQ 17
[ 19.672663] PCI: Setting latency timer of device 0000:00:07.0 to 64
[ 19.676876] FDC 0 is a post-1991 82077
[ 19.976769] usb 1-2: new full speed USB device using ohci_hcd and address 2
[ 20.179642] usb 1-2: configuration #1 chosen from 1 choice
[ 20.182572] hub 1-2:1.0: USB hub found
[ 20.185549] hub 1-2:1.0: 4 ports detected
[ 20.192868] forcedeth 0000:00:07.0: ifname eth0, PHY OUI 0x1374 @ 1, addr 00:18:f3:a9:c2:ea
[ 20.192872] forcedeth 0000:00:07.0: highdma pwrctl mgmt timirq gbit lnktim msi desc-v3
[ 20.196639] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 21
[ 20.196651] ACPI: PCI Interrupt 0000:00:02.1[b] -> Link [LUB2] -> GSI 21 (level, low) -> IRQ 18
[ 20.196661] PCI: Setting latency timer of device 0000:00:02.1 to 64
[ 20.196664] ehci_hcd 0000:00:02.1: EHCI Host Controller
[ 20.196691] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
[ 20.196719] ehci_hcd 0000:00:02.1: debug port 1
[ 20.196722] PCI: cache line size of 64 is not supported by device 0000:00:02.1
[ 20.196733] ehci_hcd 0000:00:02.1: irq 18, io mem 0xddefec00
[ 20.207929] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 20.208037] usb usb2: configuration #1 chosen from 1 choice
[ 20.208057] hub 2-0:1.0: USB hub found
[ 20.208064] hub 2-0:1.0: 10 ports detected
[ 20.311894] sata_nv 0000:00:08.0: version 3.5
[ 20.312212] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 20
[ 20.312222] ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LSA0] -> GSI 20 (level, low) -> IRQ 19
[ 20.312259] PCI: Setting latency timer of device 0000:00:08.0 to 64
[ 20.312577] scsi0 : sata_nv
[ 20.313153] scsi1 : sata_nv
[ 20.313271] ata1: SATA max UDMA/133 cmd 0xe400 ctl 0xe080 bmdma 0xd880 irq 19
[ 20.313274] ata2: SATA max UDMA/133 cmd 0xe000 ctl 0xdc00 bmdma 0xd888 irq 19
[ 20.686792] usb 1-2: USB disconnect, address 2
[ 20.779141] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 20.786823] ata1.00: ATA-7: WDC WD1600JS-55NCB1, 10.02E01, max UDMA/133
[ 20.786828] ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 20.794813] ata1.00: configured for UDMA/133
[ 21.055255] usb 2-2: new high speed USB device using ehci_hcd and address 2
[ 21.187509] usb 2-2: configuration #1 chosen from 1 choice
[ 21.187573] hub 2-2:1.0: USB hub found
[ 21.187680] hub 2-2:1.0: 4 ports detected
[ 21.262969] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 21.271136] ata2.00: ATA-7: WDC WD2500KS-00MJB0, 02.01C03, max UDMA/133
[ 21.271138] ata2.00: 488397168 sectors, multi 16: LBA48
[ 21.287104] ata2.00: configured for UDMA/133
[ 21.287688] scsi 0:0:0:0: Direct-Access ATA WDC WD1600JS-55N 10.0 PQ: 0 ANSI: 5
[ 21.288032] scsi 1:0:0:0: Direct-Access ATA WDC WD2500KS-00M 02.0 PQ: 0 ANSI: 5
[ 21.288390] ACPI: PCI Interrupt Link [LSA1] enabled at IRQ 23
[ 21.288394] ACPI: PCI Interrupt 0000:00:08.1[b] -> Link [LSA1] -> GSI 23 (level, low) -> IRQ 16
[ 21.288432] PCI: Setting latency timer of device 0000:00:08.1 to 64
[ 21.288641] scsi2 : sata_nv
[ 21.288766] scsi3 : sata_nv
[ 21.288882] ata3: SATA max UDMA/133 cmd 0xd800 ctl 0xd480 bmdma 0xd000 irq 16
[ 21.288885] ata4: SATA max UDMA/133 cmd 0xd400 ctl 0xd080 bmdma 0xd008 irq 16
[ 21.598487] ata3: SATA link down (SStatus 0 SControl 300)
[ 21.901071] usb 2-9: new high speed USB device using ehci_hcd and address 5
[ 21.917048] ata4: SATA link down (SStatus 0 SControl 300)
[ 21.929136] PCI: Setting latency timer of device 0000:00:06.0 to 64
[ 21.932609] pata_amd 0000:00:06.0: version 0.3.10
[ 21.932653] PCI: Setting latency timer of device 0000:00:06.0 to 64
[ 21.932381] scsi4 : pata_amd
[ 21.932438] scsi5 : pata_amd
[ 21.932974] ata5: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[ 21.932977] ata6: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[ 21.940874] Driver 'sd' needs updating - please use bus_type methods
[ 21.940956] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 21.940967] sd 0:0:0:0: [sda] Write Protect is off
[ 21.940969] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 21.940983] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 21.941025] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 21.941032] sd 0:0:0:0: [sda] Write Protect is off
[ 21.941034] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 21.941046] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 21.941049] sda: sda1
[ 21.953385] sd 0:0:0:0: [sda] Attached SCSI disk
[ 21.953419] sd 1:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
[ 21.953427] sd 1:0:0:0: [sdb] Write Protect is off
[ 21.953430] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 21.953441] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 21.953468] sd 1:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
[ 21.953476] sd 1:0:0:0: [sdb] Write Protect is off
[ 21.953478] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 21.953490] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 21.953492] sdb: sdb1 sdb2 < sdb5 sdb6 >
[ 21.996905] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 22.001432] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 22.001451] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 22.040366] usb 2-9: configuration #1 chosen from 1 choice
[ 22.253879] ata5.00: ATAPI: Optiarc DVD RW AD-5170A, 1.13, max UDMA/66
[ 22.349785] Attempting manual resume
[ 22.349790] swsusp: Resume From Partition 8:21
[ 22.349791] PM: Checking swsusp image.
[ 22.349439] usb 1-3: new low speed USB device using ohci_hcd and address 3
[ 22.349467] PM: Resume from disk failed.
[ 22.398673] kjournald starting. Commit interval 5 seconds
[ 22.398691] EXT3-fs: mounted filesystem with ordered data mode.
[ 22.425567] ata5.00: configured for UDMA/66
[ 22.425599] ata6: port disabled. ignoring.
[ 22.426478] scsi 4:0:0:0: CD-ROM Optiarc DVD RW AD-5170A 1.13 PQ: 0 ANSI: 5
[ 22.426543] scsi 4:0:0:0: Attached scsi generic sg2 type 5
[ 22.456009] Driver 'sr' needs updating - please use bus_type methods
[ 22.459615] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[ 22.459619] Uniform CD-ROM driver Revision: 3.20
[ 22.459661] sr 4:0:0:0: Attached scsi CD-ROM sr0
[ 22.567429] usb 1-3: configuration #1 chosen from 1 choice
[ 22.872707] usb 1-4: new low speed USB device using ohci_hcd and address 4
[ 23.086725] usb 1-4: configuration #1 chosen from 1 choice
[ 23.303215] usb 2-2.2: new high speed USB device using ehci_hcd and address 6
[ 23.413639] usb 2-2.2: configuration #1 chosen from 1 choice
[ 53.868519] parport_pc 00:06: reported by Plug and Play ACPI
[ 53.868631] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 53.898492] parport0: Printer, HEWLETT-PACKARD DESKJET 895C
[ 53.952682] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 54.092097] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x600
[ 54.092170] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x700
[ 54.116476] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 54.160026] input: Power Button (FF) as /devices/virtual/input/input1
[ 54.212795] ACPI: Power Button (FF) [PWRF]
[ 54.212928] input: Power Button (CM) as /devices/virtual/input/input2
[ 54.276730] ACPI: Power Button (CM) [PWRB]
[ 54.967215] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 22
[ 54.967276] ACPI: PCI Interrupt 0000:00:05.0[b] -> Link [LAZA] -> GSI 22 (level, low) -> IRQ 17
[ 54.967450] PCI: Setting latency timer of device 0000:00:05.0 to 64
[ 54.999911] hda_codec: Unknown model for AD1988, trying auto-probe from BIOS...
[ 55.027159] Linux agpgart interface v0.102
[ 55.163656] nvidia: module license 'NVIDIA' taints kernel.
[ 55.419951] ACPI: PCI Interrupt Link [LNED] enabled at IRQ 19
[ 55.420027] ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNED] -> GSI 19 (level, low) -> IRQ 20
[ 55.420204] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 55.420841] NVRM: loading NVIDIA UNIX x86 Kernel Module 169.12 Thu Feb 14 17:53:07 PST 2008
[ 55.438787] usbcore: registered new interface driver hiddev
[ 55.444352] input: BTC USB Multimedia Keyboard as /devices/pci0000:00/0000:00:02.0/usb1/1-3/1-3:1.0/input/input3
[ 55.509135] input,hidraw0: USB HID v1.10 Keyboard [BTC USB Multimedia Keyboard] on usb-0000:00:02.0-3
[ 55.524129] input: BTC USB Multimedia Keyboard as /devices/pci0000:00/0000:00:02.0/usb1/1-3/1-3:1.1/input/input4
[ 55.586993] input,hiddev96,hidraw1: USB HID v1.10 Device [BTC USB Multimedia Keyboard] on usb-0000:00:02.0-3
[ 55.593136] input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:02.0/usb1/1-4/1-4:1.0/input/input5
[ 55.618883] input,hidraw2: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:02.0-4
[ 55.619179] usbcore: registered new interface driver usbhid
[ 55.619245] /build/buildd/linux-2.6.24/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 55.620877] usbcore: registered new interface driver libusual
[ 55.628789] Initializing USB Mass Storage driver...
[ 55.728667] phy0: Selected rate control algorithm 'simple'
[ 55.812755] phy0: hwaddr 00:15:af:0b:24:9c, rtl8187 V1 + rtl8225z2
[ 55.812842] usbcore: registered new interface driver rtl8187
[ 55.813299] scsi6 : SCSI emulation for USB Mass Storage devices
[ 55.813422] usbcore: registered new interface driver usb-storage
[ 55.813487] USB Mass Storage support registered.
[ 55.813655] usb-storage: device found at 6
[ 55.813657] usb-storage: waiting for device to settle before scanning
[ 56.805967] lp0: using parport0 (interrupt-driven).
[ 56.819025] it87: Found IT8716F chip at 0x290, revision 1
[ 56.819102] it87: in3 is VCC (+5V)
[ 56.819163] it87: in7 is VCCH (+5V Stand-By)
[ 57.010745] Adding 2184800k swap on /dev/sdb5. Priority:-1 extents:1 across:2184800k
[ 60.803867] usb-storage: device scan complete
[ 60.804868] scsi 6:0:0:0: Direct-Access Corsair Flash Voyager 1100 PQ: 0 ANSI: 0 CCS
[ 60.806598] sd 6:0:0:0: [sdc] 31719424 512-byte hardware sectors (16240 MB)
[ 60.807342] sd 6:0:0:0: [sdc] Write Protect is off
[ 60.807345] sd 6:0:0:0: [sdc] Mode Sense: 43 00 00 00
[ 60.807347] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[ 60.810087] sd 6:0:0:0: [sdc] 31719424 512-byte hardware sectors (16240 MB)
[ 60.810837] sd 6:0:0:0: [sdc] Write Protect is off
[ 60.810839] sd 6:0:0:0: [sdc] Mode Sense: 43 00 00 00
[ 60.810841] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[ 60.810907] sdc: sdc1
[ 60.811647] sd 6:0:0:0: [sdc] Attached SCSI removable disk
[ 60.811683] sd 6:0:0:0: Attached scsi generic sg3 type 0
[ 71.359788] EXT3 FS on sdb1, internal journal
[ 86.941738] kjournald starting. Commit interval 5 seconds
[ 86.941972] EXT3 FS on sdb6, internal journal
[ 86.941977] EXT3-fs: mounted filesystem with ordered data mode.
[ 99.494426] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 102.332468] No dock devices found.
[ 105.043839] powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ processors (2 cpu cores) (version 2.20.00)
[ 105.044333] powernow-k8: 0 : fid 0xc (2000 MHz), vid 0xc
[ 105.044337] powernow-k8: 1 : fid 0xa (1800 MHz), vid 0xe
[ 105.044340] powernow-k8: 2 : fid 0x2 (1000 MHz), vid 0x12
[ 109.143074] ppdev: user-space parallel port driver
[ 109.622707] audit(1214113003.196:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=10834 profile="/usr/sbin/cupsd" namespace="default"
[ 109.658065] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 109.658070] apm: disabled - APM is not SMP safe.
[ 123.134180] Clocksource tsc unstable (delta = -250022794 ns)
[ 126.959202] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[ 126.959208] vboxdrv: Successfully done.
[ 126.959210] vboxdrv: Found 2 processor cores.
[ 126.959231] vboxdrv: fAsync=1 u64DiffCores=880013.
[ 126.959271] vboxdrv: TSC mode is 'asynchronous', kernel timer mode is 'normal'.
[ 126.959274] vboxdrv: Successfully loaded version 1.6.2 (interface 0x00070002).
[ 131.260523] eth0: no link during initialization.
[ 131.298775] Bluetooth: Core ver 2.11
[ 131.299126] NET: Registered protocol family 31
[ 131.299130] Bluetooth: HCI device and connection manager initialized
[ 131.299134] Bluetooth: HCI socket layer initialized
[ 131.309253] Bluetooth: L2CAP ver 2.9
[ 131.309257] Bluetooth: L2CAP socket layer initialized
[ 131.336363] Bluetooth: RFCOMM socket layer initialized
[ 131.336377] Bluetooth: RFCOMM TTY layer initialized
[ 131.336379] Bluetooth: RFCOMM ver 1.8
[ 207.607270] NET: Registered protocol family 10
[ 207.607486] lo: Disabled Privacy Extensions
[ 207.607934] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 207.608383] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 233.327114] NET: Registered protocol family 17
[ 234.941041] wlan0: Initial auth_alg=0
[ 234.941049] wlan0: authenticate with AP 00:0f:3d:97:14:7a
[ 234.942002] wlan0: RX authentication from 00:0f:3d:97:14:7a (alg=0 transaction=2 status=0)
[ 234.942007] wlan0: authenticated
[ 234.942010] wlan0: associate with AP 00:0f:3d:97:14:7a
[ 234.951803] wlan0: RX AssocResp from 00:0f:3d:97:14:7a (capab=0x461 status=0 aid=1)
[ 234.951808] wlan0: associated
[ 234.951811] wlan0: switched to short barker preamble (BSSID=00:0f:3d:97:14:7a)
[ 234.953020] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 240.038793] wlan0: no IPv6 routers present
[ 253.961751] wlan0: no IPv6 routers presentEt le rapport de smartctl (après un smartctl --test=long il y a quelques semaines)
xavier@ubuntu:~$ sudo smartctl -a /dev/sdb
smartctl version 5.37 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar SE16 family
Device Model: WDC WD2500KS-00MJB0
Serial Number: WD-WCANKF400907
Firmware Version: 02.01C03
User Capacity: 250'059'350'016 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sun Jun 22 09:10:27 2008 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (8280) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 96) minutes.
Conveyance self-test routine
recommended polling time: ( 6) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 188 188 051 Pre-fail Always - 20556
3 Spin_Up_Time 0x0003 195 189 021 Pre-fail Always - 5241
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 358
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 1595
10 Spin_Retry_Count 0x0013 100 100 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0012 100 100 051 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 299
190 Temperature_Celsius 0x0022 060 050 045 Old_age Always - 40
194 Temperature_Celsius 0x0022 110 100 000 Old_age Always - 40
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 199 199 000 Old_age Always - 48
198 Offline_Uncorrectable 0x0010 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0009 197 179 051 Pre-fail Offline - 129
SMART Error Log Version: 1
ATA Error Count: 42 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 42 occurred at disk power-on lifetime: 1593 hours (66 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 b7 19 4c e0 Error: UNC at LBA = 0x004c19b7 = 4987319
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 38 8f 19 4c 00 00 00:09:21.298 READ DMA
c8 00 08 87 19 4c 00 00 00:09:16.462 READ DMA
c8 00 20 7f 83 77 02 00 00:09:16.456 READ DMA
c8 00 08 87 00 74 02 00 00:09:12.530 READ DMA
c8 00 08 f7 00 74 02 00 00:09:11.331 READ DMA
Error 41 occurred at disk power-on lifetime: 1593 hours (66 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 60 19 4c e0 Error: UNC at LBA = 0x004c1960 = 4987232
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 5f 19 4c 00 00 00:03:40.200 READ DMA
27 00 00 00 00 00 00 00 00:03:40.200 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 00 00:03:40.193 IDENTIFY DEVICE
ef 03 46 00 00 00 00 00 00:03:40.193 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00:03:40.193 READ NATIVE MAX ADDRESS EXT
Error 40 occurred at disk power-on lifetime: 1593 hours (66 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 5f 19 4c e0 Error: UNC at LBA = 0x004c195f = 4987231
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 5f 19 4c 00 00 00:03:38.326 READ DMA
27 00 00 00 00 00 00 00 00:03:38.326 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 00 00:03:38.318 IDENTIFY DEVICE
ef 03 46 00 00 00 00 00 00:03:38.318 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00:03:38.318 READ NATIVE MAX ADDRESS EXT
Error 39 occurred at disk power-on lifetime: 1593 hours (66 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 5f 19 4c e0 Error: UNC at LBA = 0x004c195f = 4987231
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 5f 19 4c 00 00 00:03:36.397 READ DMA
27 00 00 00 00 00 00 00 00:03:36.397 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 00 00:03:36.388 IDENTIFY DEVICE
ef 03 46 00 00 00 00 00 00:03:36.388 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00:03:36.388 READ NATIVE MAX ADDRESS EXT
Error 38 occurred at disk power-on lifetime: 1593 hours (66 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 5f 19 4c e0 Error: UNC at LBA = 0x004c195f = 4987231
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 5f 19 4c 00 00 00:03:34.482 READ DMA
27 00 00 00 00 00 00 00 00:03:34.482 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 00 00 00:03:34.475 IDENTIFY DEVICE
ef 03 46 00 00 00 00 00 00:03:34.475 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00:03:34.475 READ NATIVE MAX ADDRESS EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 1298 -
# 2 Extended offline Aborted by host 90% 1274 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.Dernière modification par Calimo (Le 28/09/2008, à 15:03)
Hors ligne
#2 Le 26/06/2008, à 19:57
- Calimo
Re : [Résolu] Erreurs Emask, kernel panic, disque lent...
Là à l'instant j'ai eu droit à des
ata 2.00: status: {DRDY ERR}
ata 2.00: err: {UNC}en boucle.
Ca a fini par passer. Je commence à désespérer un peu 
Hors ligne
#3 Le 29/07/2008, à 19:21
- Calimo
Re : [Résolu] Erreurs Emask, kernel panic, disque lent...
Bonjour/soir
Me voilà de retour de vacances, dimanche, je boote, je reviens 10' plus tard et j'ai des lignes de texte blanches qui défilent trop vite pour voir ce qu'elles disent. Alt+SysRq+REISUB, et ça passe nickel là 2è fois.
Ce soir, je démarre, grub s'affiche, enter, et là j'ai juste un curseur _ qui clignotte. 10' plus tard, reboot, rebelotte. Je passe en liveCD, là le disque est reconnu nickel chrome. Je fais un check, je redémarre, et ça passe. Je ne comprend vraiment pas
Je pense de moins en moins à un souci matériel au vu des tests (cf plus haut), du fait que grub (qui se trouve sur le disque, je n'ai pas de /boot séparé) fonctionne, et que le disque marche en liveCD : c'est uniquement au moment du boot que ça coince.
Manifestement, personne n'a de réponse ici. Savez-vous où est-ce que je pourrais m'adresser pour trouver une solution à mon souci ?
Merci
Hors ligne
#4 Le 03/08/2008, à 17:51
- Calimo
Re : [Résolu] Erreurs Emask, kernel panic, disque lent...
ata2: port is slow [...] (status 0x80)
COMRESET failed (errno=-16)puis
end_request: I/O error, dev sdb, sector 41424983 driverbyte=DRIVER_OK, SUGGEST_OKIl semblerait que certains aient résolu des erreurs de ce type en passant irqpoll au kernel. Je vais essayer cela.
Hors ligne
#5 Le 23/08/2008, à 18:41
- Calimo
Re : [Résolu] Erreurs Emask, kernel panic, disque lent...
J'ai redimensionné sda1 et créé une partition sda2. J'y ai installé Ubuntu Hardy. Voilà plusieurs fois que ça boote bien. Ce qui est plus étonnant, c'est que ça boote aussi sans problème sur sdb1... alors que le disque est strictement inchangé. Est-il possible la position du bootloader puisse avoir une influence ?
Je vais voir à l'usage si ça dure
Hors ligne
#6 Le 28/09/2008, à 15:02
- Calimo
Re : [Résolu] Erreurs Emask, kernel panic, disque lent...
Bon après plus d'1 mois je n'ai pas eu de nouveau problème. Mais je n'ai pas franchement compris ce qui s'est passé.
Je marque le sujet comme résolu.
Hors ligne