toujours des freeze....

Denis29 · Le 23/06/2006, à 20:47

Hello
Dapper 6.0.6
Toujours des freeze. J'ai installé les pilotes NVidia, suivi toutes les procédures et tout continue à se bloquer, très souvent, de façon complètement aléatoire. C'est vraiment très ennuyeux.
Ce que j'aimerais découvrir c'est quelles sont les causes possibles de ce genre d'incident. Cela me permettra peut-être de mieux sérier le problème.
Merci

denis

cflam69 · Le 23/06/2006, à 20:56

as-tu essayé de voir ce que répond dmesg ?

Denis29 · Le 23/06/2006, à 21:54

Voila ce que donne dmesg.
Si tu trouves ce qui cloche, ce srait sympa...

[17179569.184000] Linux version 2.6.15-25-386 (buildd@terranova) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 PREEMPT Wed Jun 14 11:25:49 UTC 2006
[17179569.184000] BIOS-provided physical RAM map:
[17179569.184000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[17179569.184000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[17179569.184000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[17179569.184000] BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
[17179569.184000] BIOS-e820: 000000003fff0000 - 000000003fff8000 (ACPI data)
[17179569.184000] BIOS-e820: 000000003fff8000 - 0000000040000000 (ACPI NVS)
[17179569.184000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[17179569.184000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[17179569.184000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[17179569.184000] 127MB HIGHMEM available.
[17179569.184000] 896MB LOWMEM available.
[17179569.184000] found SMP MP-table at 000fb930
[17179569.184000] On node 0 totalpages: 262128
[17179569.184000] DMA zone: 4096 pages, LIFO batch:0
[17179569.184000] DMA32 zone: 0 pages, LIFO batch:0
[17179569.184000] Normal zone: 225280 pages, LIFO batch:31
[17179569.184000] HighMem zone: 32752 pages, LIFO batch:7
[17179569.184000] DMI 2.3 present.
[17179569.184000] ACPI: RSDP (v000 AMI ) @ 0x000fa940
[17179569.184000] ACPI: RSDT (v001 AMIINT VIA_K7 0x00000010 MSFT 0x00000097) @ 0x3fff0000
[17179569.184000] ACPI: FADT (v001 AMIINT VIA_K7 0x00000011 MSFT 0x00000097) @ 0x3fff0030
[17179569.184000] ACPI: MADT (v001 AMIINT VIA_K7 0x00000009 MSFT 0x00000097) @ 0x3fff00c0
[17179569.184000] ACPI: DSDT (v001 VIA VIA_K7 0x00001000 MSFT 0x0100000d) @ 0x00000000
[17179569.184000] ACPI: PM-Timer IO Port: 0x808
[17179569.184000] ACPI: Local APIC address 0xfee00000
[17179569.184000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[17179569.184000] Processor #0 6:10 APIC version 16
[17179569.184000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[17179569.184000] IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
[17179569.184000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[17179569.184000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[17179569.184000] ACPI: IRQ0 used by override.
[17179569.184000] ACPI: IRQ2 used by override.
[17179569.184000] ACPI: IRQ9 used by override.
[17179569.184000] Enabling APIC mode: Flat. Using 1 I/O APICs
[17179569.184000] Using ACPI (MADT) for SMP configuration information
[17179569.184000] Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
[17179569.184000] Built 1 zonelists
[17179569.184000] Kernel command line: root=/dev/hda1 ro quiet splash
[17179569.184000] mapped APIC to ffffd000 (fee00000)
[17179569.184000] mapped IOAPIC to ffffc000 (fec00000)
[17179569.184000] Initializing CPU#0
[17179569.184000] PID hash table entries: 4096 (order: 12, 65536 bytes)
[17179569.184000] Detected 1921.245 MHz processor.
[17179569.184000] Using pmtmr for high-res timesource
[17179569.184000] Console: colour VGA+ 80x25
[17179569.264000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[17179569.264000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)[17179569.300000] Memory: 1028816k/1048512k available (1976k kernel code, 18928k reserved, 606k data, 288k init, 131008k highmem)
[17179569.300000] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[17179569.380000] Calibrating delay using timer specific routine.. 3846.14 BogoMIPS (lpj=7692298)
[17179569.380000] Security Framework v1.0.0 initialized
[17179569.380000] SELinux: Disabled at boot.
[17179569.380000] Mount-cache hash table entries: 512
[17179569.380000] CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
[17179569.380000] CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
[17179569.380000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[17179569.380000] CPU: L2 Cache: 512K (64 bytes/line)
[17179569.380000] CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000420 00000000 00000000 00000000
[17179569.380000] mtrr: v2.0 (20020519)
[17179569.380000] CPU: AMD Athlon(tm) XP 2600+ stepping 00
[17179569.380000] Enabling fast FPU save and restore... done.
[17179569.380000] Enabling unmasked SIMD FPU exception support... done.
[17179569.380000] Checking 'hlt' instruction... OK.
[17179569.396000] checking if image is initramfs... it is
[17179569.940000] Freeing initrd memory: 6611k freed
[17179569.952000] ACPI: Looking for DSDT ... not found!
[17179569.956000] ENABLING IO-APIC IRQs
[17179569.956000] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[17179570.100000] NET: Registered protocol family 16
[17179570.100000] EISA bus registered
[17179570.100000] ACPI: bus type pci registered
[17179570.100000] PCI: PCI BIOS revision 2.10 entry at 0xfdaf1, last bus=1
[17179570.100000] PCI: Using configuration type 1
[17179570.100000] ACPI: Subsystem revision 20051216
[17179570.104000] ACPI: Interpreter enabled
[17179570.104000] ACPI: Using IOAPIC for interrupt routing
[17179570.108000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[17179570.108000] PCI: Probing PCI hardware (bus 00)
[17179570.108000] PCI quirk: region 0800-087f claimed by vt8235 PM
[17179570.108000] PCI quirk: region 0400-040f claimed by vt8235 SMB
[17179570.108000] Boot video device is 0000:01:00.0
[17179570.108000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[17179570.116000] ACPI: Power Resource [URP1] (off)
[17179570.116000] ACPI: Power Resource [URP2] (off)
[17179570.116000] ACPI: Power Resource [FDDP] (off)
[17179570.116000] ACPI: Power Resource [LPTP] (off)
[17179570.116000] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[17179570.116000] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[17179570.116000] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[17179570.116000] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[17179570.116000] Linux Plug and Play Support v0.97 (c) Adam Belay
[17179570.116000] pnp: PnP ACPI init
[17179570.120000] pnp: PnP ACPI: found 11 devices
[17179570.120000] PnPBIOS: Disabled by ACPI PNP
[17179570.120000] PCI: Using ACPI for IRQ routing
[17179570.120000] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[17179570.120000] PCI: Bridge: 0000:00:01.0
[17179570.120000] IO window: disabled.
[17179570.120000] MEM window: ddd00000-dfdfffff
[17179570.120000] PREFETCH window: d5c00000-ddbfffff
[17179570.120000] PCI: Setting latency timer of device 0000:00:01.0 to 64
[17179570.124000] audit: initializing netlink socket (disabled)
[17179570.124000] audit(1151178572.124:1): initialized
[17179570.124000] highmem bounce pool size: 64 pages
[17179570.124000] VFS: Disk quotas dquot_6.5.1
[17179570.124000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[17179570.124000] Initializing Cryptographic API
[17179570.124000] io scheduler noop registered
[17179570.124000] io scheduler anticipatory registered
[17179570.124000] io scheduler deadline registered
[17179570.124000] io scheduler cfq registered
[17179570.124000] isapnp: Scanning for PnP cards...
[17179570.476000] isapnp: No Plug & Play device found
[17179570.488000] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[17179570.488000] serio: i8042 AUX port at 0x60,0x64 irq 12
[17179570.488000] serio: i8042 KBD port at 0x60,0x64 irq 1
[17179570.488000] Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
[17179570.488000] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179570.488000] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[17179570.492000] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179570.492000] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[17179570.492000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[17179570.492000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[17179570.492000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[17179570.492000] mice: PS/2 mouse device common for all mice
[17179570.492000] EISA: Probing bus 0 at eisa.0
[17179570.492000] EISA: Detected 0 cards.
[17179570.492000] NET: Registered protocol family 2
[17179570.516000] input: AT Translated Set 2 keyboard as /class/input/input0
[17179570.528000] IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
[17179570.528000] TCP established hash table entries: 262144 (order: 8, 1048576 bytes)
[17179570.528000] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[17179570.528000] TCP: Hash tables configured (established 262144 bind 65536)
[17179570.528000] TCP reno registered
[17179570.528000] TCP bic registered
[17179570.528000] NET: Registered protocol family 1
[17179570.528000] NET: Registered protocol family 8
[17179570.528000] NET: Registered protocol family 20
[17179570.528000] Using IPI Shortcut mode
[17179570.528000] ACPI wakeup devices:
[17179570.528000] PCI0 USB1 USB2 USB3 EHCI UAR1 AC9 MC9 ILAN SLPB
[17179570.528000] ACPI: (supports S0 S1 S4 S5)
[17179570.528000] Freeing unused kernel memory: 288k freed
[17179570.576000] vga16fb: initializing
[17179570.576000] vga16fb: mapped to 0xc00a0000
[17179570.708000] Console: switching to colour frame buffer device 80x25
[17179570.708000] fb0: VGA16 VGA frame buffer device
[17179571.840000] Capability LSM initialized
[17179572.280000] CMD649: IDE controller at PCI slot 0000:00:05.0
[17179572.280000] ACPI: PCI Interrupt 0000:00:05.0[A] -> GSI 16 (level, low) -> IRQ 169
[17179572.280000] CMD649: chipset revision 2
[17179572.280000] CMD649: ROM enabled at 0xdff80000
[17179572.280000] CMD649: 100% native mode on irq 169
[17179572.280000] ide0: BM-DMA at 0xdc00-0xdc07, BIOS settings: hda:pio, hdb:pio
[17179572.280000] ide1: BM-DMA at 0xdc08-0xdc0f, BIOS settings: hdc:pio, hdd:pio
[17179572.280000] Probing IDE interface ide0...
[17179572.568000] hda: ExcelStor Technology J880, ATA DISK drive
[17179573.240000] ide0 at 0xec00-0xec07,0xe802 on irq 169
[17179573.240000] Probing IDE interface ide1...
[17179573.528000] hdc: SAMSUNG SP0411N, ATA DISK drive
[17179574.200000] ide1 at 0xe400-0xe407,0xe002 on irq 169
[17179574.208000] hda: max request size: 1024KiB
[17179574.220000] hda: 160836480 sectors (82348 MB) w/1719KiB Cache, CHS=16383/255/63, UDMA(33)
[17179574.220000] hda: cache flushes supported
[17179574.220000] hda: hda1 hda2 < hda5 >
[17179574.244000] hdc: max request size: 1024KiB
[17179574.244000] hdc: 78242976 sectors (40060 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
[17179574.244000] hdc: cache flushes supported
[17179574.244000] hdc: hdc1 < hdc5 >
[17179574.456000] VP_IDE: IDE controller at PCI slot 0000:00:11.1
[17179574.456000] ACPI: PCI Interrupt 0000:00:11.1[A]: no GSI
[17179574.456000] PCI: Via IRQ fixup for 0000:00:11.1, from 255 to 15
[17179574.456000] VP_IDE: chipset revision 6
[17179574.456000] VP_IDE: not 100% native mode: will probe irqs later
[17179574.456000] VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
[17179574.456000] ide2: BM-DMA at 0xfc00-0xfc07, BIOS settings: hde:DMA, hdf:DMA
[17179574.456000] ide3: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdg:DMA, hdh:DMA
[17179574.456000] Probing IDE interface ide2...
[17179574.872000] hde: WDC WD400BB-22DEA0, ATA DISK drive
[17179575.656000] hdf: _NEC DV-5700A, ATAPI CD/DVD-ROM drive
[17179575.712000] ide2 at 0x1f0-0x1f7,0x3f6 on irq 14
[17179575.728000] hde: max request size: 128KiB
[17179575.732000] hde: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
[17179575.732000] hde: cache flushes not supported
[17179575.732000] hde: hde1 hde2 < hde5 hde6 >
[17179575.764000] Probing IDE interface ide3...
[17179576.180000] hdg: HDS722580VLAT20, ATA DISK drive
[17179576.964000] hdh: SONY DVD RW DW-D22A, ATAPI CD/DVD-ROM drive
[17179577.020000] ide3 at 0x170-0x177,0x376 on irq 15
[17179577.032000] hdg: max request size: 1024KiB
[17179577.032000] hdg: 160836480 sectors (82348 MB) w/1794KiB Cache, CHS=16383/255/63, UDMA(100)
[17179577.032000] hdg: cache flushes supported
[17179577.032000] hdg: hdg1 hdg2 < >
[17179577.080000] hdf: ATAPI 40X DVD-ROM drive, 256kB Cache, UDMA(33)
[17179577.080000] Uniform CD-ROM driver Revision: 3.20
[17179577.080000] hdh: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
[17179577.328000] usbcore: registered new driver usbfs
[17179577.328000] usbcore: registered new driver hub
[17179577.328000] USB Universal Host Controller Interface driver v2.3
[17179577.332000] ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 177
[17179577.332000] PCI: Via IRQ fixup for 0000:00:10.0, from 11 to 1
[17179577.332000] uhci_hcd 0000:00:10.0: UHCI Host Controller
[17179577.332000] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
[17179577.332000] uhci_hcd 0000:00:10.0: irq 177, io base 0x0000c400
[17179577.332000] hub 1-0:1.0: USB hub found
[17179577.332000] hub 1-0:1.0: 2 ports detected
[17179577.436000] ACPI: PCI Interrupt 0000:00:10.1[b] -> GSI 21 (level, low) -> IRQ 177
[17179577.436000] PCI: Via IRQ fixup for 0000:00:10.1, from 10 to 1
[17179577.436000] uhci_hcd 0000:00:10.1: UHCI Host Controller
[17179577.436000] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
[17179577.436000] uhci_hcd 0000:00:10.1: irq 177, io base 0x0000c800
[17179577.436000] hub 2-0:1.0: USB hub found
[17179577.436000] hub 2-0:1.0: 2 ports detected
[17179577.540000] ACPI: PCI Interrupt 0000:00:10.2[C] -> GSI 21 (level, low) -> IRQ 177
[17179577.540000] PCI: Via IRQ fixup for 0000:00:10.2, from 5 to 1
[17179577.540000] uhci_hcd 0000:00:10.2: UHCI Host Controller
[17179577.540000] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
[17179577.540000] uhci_hcd 0000:00:10.2: irq 177, io base 0x0000cc00
[17179577.540000] hub 3-0:1.0: USB hub found
[17179577.540000] hub 3-0:1.0: 2 ports detected
[17179577.644000] ACPI: PCI Interrupt 0000:00:10.3[D] -> GSI 21 (level, low) -> IRQ 177
[17179577.644000] PCI: Via IRQ fixup for 0000:00:10.3, from 5 to 1
[17179577.644000] ehci_hcd 0000:00:10.3: EHCI Host Controller
[17179577.644000] ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
[17179577.644000] ehci_hcd 0000:00:10.3: irq 177, io mem 0xdff5fe00
[17179577.644000] ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[17179577.644000] hub 4-0:1.0: USB hub found
[17179577.644000] hub 4-0:1.0: 6 ports detected
[17179577.832000] Attempting manual resume
[17179577.840000] EXT3-fs: INFO: recovery required on readonly filesystem.
[17179577.840000] EXT3-fs: write access will be enabled during recovery.
[17179578.540000] usb 4-2: new high speed USB device using ehci_hcd and address 2
[17179578.856000] hub 4-0:1.0: over-current change on port 5
[17179578.960000] hub 4-0:1.0: over-current change on port 6
[17179579.304000] usb 2-1: new full speed USB device using uhci_hcd and address 2
[17179581.692000] EXT3-fs: recovery complete.
[17179581.692000] kjournald starting. Commit interval 5 seconds
[17179581.692000] EXT3-fs: mounted filesystem with ordered data mode.
[17179591.708000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[17179591.720000] 8139too Fast Ethernet driver 0.9.27
[17179591.720000] ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 185
[17179591.720000] eth0: RealTek RTL8139 at 0xf8890f00, 00:50:fc:b1:a8:01, IRQ 185
[17179591.720000] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
[17179591.744000] 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
[17179591.752000] Linux agpgart interface v0.101 (c) Dave Jones
[17179591.756000] agpgart: Detected VIA KT400/KT400A/KT600 chipset
[17179591.764000] agpgart: AGP aperture is 128M @ 0xe0000000
[17179591.768000] Linux video capture interface: v1.00
[17179591.816000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[17179591.924000] hsfengine: module license 'see LICENSE file distributed with driver' taints kernel.
[17179591.940000] ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 18 (level, low) -> IRQ 193
[17179592.028000] bttv: driver version 0.9.16 loaded
[17179592.028000] bttv: using 8 buffers with 2080k (520 pages) each for capture
[17179592.028000] bttv: Bt8xx card found (0).
[17179592.028000] ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 17 (level, low) -> IRQ 185
[17179592.028000] bttv0: Bt878 (rev 17) at 0000:00:06.0, irq: 185, latency: 32, mmio: 0xddcfe000
[17179592.028000] bttv0: detected: Pinnacle PCTV [card=39], PCI subsystem ID is 11bd:0012
[17179592.028000] bttv0: using: Pinnacle PCTV Studio/Rave [card=39,autodetected][17179592.028000] bttv0: gpio: en=00000000, out=00000000 in=00fffbff [init]
[17179592.028000] bttv0: i2c: checking for MSP34xx @ 0x80... found
[17179592.032000] bttv0: pinnacle/mt: id=2 info="PAL+SECAM / stereo" radio=yes
[17179592.032000] bttv0: using tuner=33
[17179592.032000] bttv0: i2c: checking for MSP34xx @ 0x80... found
[17179592.096000] via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
[17179592.188000] irda_init()
[17179592.188000] NET: Registered protocol family 23
[17179592.636000] msp3400 0-0040: chip=MSP3410G-B11 +nicam +simple +simpler +radio mode=simpler
[17179592.636000] msp3400 0-0040: msp34xxg daemon started
[17179592.700000] bttv0: i2c: checking for TDA9875 @ 0xb0... not found
[17179592.704000] bttv0: i2c: checking for TDA7432 @ 0x8a... not found
[17179592.732000] tda9887 0-004b: chip found @ 0x96 (bt878 #0 [sw])
[17179592.760000] tuner 0-0060: Chip ID is not zero. It is not a TEA5767
[17179592.760000] tuner 0-0060: chip found @ 0xc0 (bt878 #0 [sw])
[17179592.768000] tuner 0-0060: microtune: companycode=3cbf part=42 rev=22
[17179592.772000] tuner 0-0060: microtune MT2050 found, OK
[17179592.836000] bttv0: registered device video0
[17179592.836000] bttv0: registered device vbi0
[17179592.836000] bttv0: registered device radio0
[17179592.880000] bttv0: PLL: 28636363 => 35468950 .. ok
[17179592.972000] ttySHSF0 at I/O 0xd800 (irq = 193) is a Conexant HSF softmodem (PCI-14f1:2f00-14f1:2004)
[17179592.972000] ACPI: PCI Interrupt 0000:00:08.0[A] -> GSI 19 (level, low) -> IRQ 201
[17179592.996000] input: ImExPS/2 Generic Explorer Mouse as /class/input/input1
[17179593.132000] parport: PnPBIOS parport detected.
[17179593.136000] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[17179593.296000] Real Time Clock Driver v1.12
[17179593.372000] input: PC Speaker as /class/input/input2
[17179593.380000] Floppy drive(s): fd0 is 1.44M
[17179593.416000] FDC 0 is a post-1991 82077
[17179593.552000] eth0: link down
[17179593.620000] usbcore: registered new driver snd-usb-audio
[17179593.792000] ts: Compaq touchscreen protocol output
[17179593.920000] ttySHSF1 at I/O 0xd400 (irq = 201) is a Conexant HSF softmodem (PCI-14f1:2f00-14f1:2000)
[17179593.920000] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 209
[17179593.920000] PCI: Via IRQ fixup for 0000:00:12.0, from 11 to 1
[17179593.924000] eth1: VIA Rhine II at 0x1bc00, 00:0c:76:59:c2:28, IRQ 209.
[17179593.924000] eth1: MII PHY found at address 1, status 0x786d advertising 01e1 Link 45e1.
[17179593.928000] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169
[17179593.928000] NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-8762 Mon May 15 13:06:38 PDT 2006
[17179594.008000] bt878: AUDIO driver version 0.0.0 loaded
[17179594.008000] bt878: Bt878 AUDIO function found (0).
[17179594.008000] ACPI: PCI Interrupt 0000:00:06.1[A] -> GSI 17 (level, low) -> IRQ 185
[17179594.008000] bt878(0): Bt878 (rev 17) at 00:06.1, irq: 185, latency: 32, memory: 0xddcff000
[17179594.012000] ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 217
[17179594.012000] PCI: Via IRQ fixup for 0000:00:11.5, from 5 to 9
[17179594.012000] PCI: Setting latency timer of device 0000:00:11.5 to 64
[17179594.576000] NET: Registered protocol family 17
[17179595.312000] eth1: link up, 100Mbps, full-duplex, lpa 0x45E1
[17179595.584000] lp0: using parport0 (interrupt-driven).
[17179595.640000] Adding 3028212k swap on /dev/hda5. Priority:-1 extents:1 across:3028212k
[17179595.792000] EXT3 FS on hda1, internal journal
[17179595.928000] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
[17179595.928000] md: bitmap version 4.39
[17179596.632000] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
[17179596.920000] cdrom: open failed.
[17179597.204000] cdrom: open failed.
[17179597.204000] cdrom: open failed.
[17179597.960000] NET: Registered protocol family 10
[17179597.960000] lo: Disabled Privacy Extensions
[17179597.960000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[17179597.960000] IPv6 over IPv4 tunneling driver
[17179604.172000] ACPI: Power Button (FF) [PWRF]
[17179604.172000] ACPI: Power Button (CM) [PWRB]
[17179604.172000] ACPI: Sleep Button (CM) [SLPB]
[17179604.280000] ibm_acpi: ec object not found
[17179604.308000] pcc_acpi: loading...
[17179608.872000] eth1: no IPv6 routers present
[17179619.424000] agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
[17179619.424000] agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
[17179619.424000] agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
[17179619.940000] ppdev: user-space parallel port driver
[17179620.580000] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[17179620.580000] apm: overridden by ACPI.
[17179627.068000] ip_tables: (C) 2000-2002 Netfilter core team
[17179627.196000] Netfilter messages via NETLINK v0.30.
[17179627.204000] ip_conntrack version 2.4 (8191 buckets, 65528 max) - 232 bytes per conntrack
[17179631.436000] Bluetooth: Core ver 2.8
[17179631.436000] NET: Registered protocol family 31
[17179631.436000] Bluetooth: HCI device and connection manager initialized
[17179631.436000] Bluetooth: HCI socket layer initialized
[17179631.456000] Bluetooth: L2CAP ver 2.8
[17179631.456000] Bluetooth: L2CAP socket layer initialized
[17179631.460000] Bluetooth: RFCOMM socket layer initialized
[17179631.460000] Bluetooth: RFCOMM TTY layer initialized
[17179631.460000] Bluetooth: RFCOMM ver 1.7
[17179727.428000] Inbound IN=eth1 OUT= MAC=00:0c:76:59:c2:28:00:40:f4:ad:21:44:08:00 SRC=207.46.6.80 DST=192.168.1.18 LEN=49 TOS=0x00 PREC=0x00 TTL=117 ID=25055 PROTO=TCP SPT=1863 DPT=47202 WINDOW=65004 RES=0x00 ACK PSH URGP=0

Merci

cflam69 · Le 23/06/2006, à 23:52

Euh, c'est plus cool de mettre ce genre de chose entre des balises (code)(/code)
Sinon, malheureusement, il n'y a pas de message d'alerte qui pourrait donner une piste.
Comment se passe tes freezes (programmes utilisés, ...) ? Est-ce aléatoire ? C'est un plantage complet ou peux-tu redémarrer le serveur X ?
La swap ou la mémoire saturent-elles ?
Pourquoi penses-tu que l'install de tes drivers video améliore la situation ?
As-tu essayé un autre environnement que Gnome pour voir ?

Dernière modification par cflam69 (Le 23/06/2006, à 23:52)

esox · Le 15/11/2007, à 17:02

J'ai un soucis similaire sous Gnome Compiz Gutsy et carte ATI. La fenêtre active se fige, passe en N&B, par contre j'ai toujours la main pour lancer une autre appli, un terminal par exemple. Ca dure qq secondes et tout redevient normal. C'est aléatoire. Mais ça rend le PC inutilisable... un "top" ne donne rien de significatif, si ce n'est une ligne ata/0 qui se crée à ces moments là avec peu de charge cpu et mémoire (moins de 15%).

J'ai bien un swap en /dev6

Une idée ?

Merci

[GO]Skywalker13 · Le 29/12/2007, à 20:59

Le problème du gars précédent c'est à cause de don lecteur DVD DV-5700A de NEC qui bug avec HAL et qui fait tourner tout le système en freeze (le dernier firmware ne change rien). Rien à voir avec la carte vidéo..

J'ai le même lecteur DVD et j'ai jamais trouvé de moyen de fixer.

esox · Le 02/01/2008, à 19:32

Personnellement je n'ai plsu de freeze, je n'ai rien fait de particulier à part les MAJ et aussi changé mon TSST pour un LG, mais le probleme était résolu avant ce changement

Ubuntu-fr

Navigation

Liens de recherche

Annonce

#1 Le 23/06/2006, à 20:47

toujours des freeze....

#2 Le 23/06/2006, à 20:56

Re : toujours des freeze....

#3 Le 23/06/2006, à 21:54

Re : toujours des freeze....

#4 Le 23/06/2006, à 23:52

Re : toujours des freeze....

#5 Le 15/11/2007, à 17:02

Re : toujours des freeze....

#6 Le 29/12/2007, à 20:59

Re : toujours des freeze....

#7 Le 02/01/2008, à 19:32

Re : toujours des freeze....

Pied de page des forums