#1 Le 08/08/2006, à 00:44
- lautoine0
installation modem usb adsl : conceptronic CADSLUG version 1.0-12
Bonjour,
Je viens d'essayer le live cd de Ubuntu 6.06, génial, car j'avais un problème d'installation avec la version 5.10. (Utilisateur novice un peu expérimenté).
Configuration : PC AMD64 3200+, 1Gb de ram en dual, carte mère Gigabyte GA-K8N51GMF-9.
Le problème : Je possède un modem Conceptronic Adsl USB L+DMT ( CADSLUG version 1.0-12) avec une puce GlobeSpan inc., le problème il ne fonctionne pas (led vert clignote)
En utilisant le live CD, dans le gestionnaire de périphérique, mon modem est référencé sur le port USB. Je trouve donc les paramètres suivants :
usb.vendor-id : int : 2325 (0x915)
usb.speed-bcd : int : 4608 (0x915)
usb.serial : strlist : 0c67f4
usb.product-id : int : 32768 (0x8000)
usb.product : strlist : usb vendor specific interface
usb.device vendor : strlist : GlobeSpan INC
usb.device vendor-id : int : 2325
Question :
Y a-t'-il un drivers, un package ou une procédure pour pouvoir l'installer?
J'ai trouvé des renseignements pour le modem EciAdsl avec la même puce, mais puis-je l'utiliser?
Dans la négative, j'ai la possibilité d'acheter un modem D-Link DSL-320T avec connexion ethernet modem/pc. Sera-t'-il utilisable sur Ubuntu?
Voilà, j'ai fini.
Merci pour l'aide que vous pourriez m'apporter.
#2 Le 08/08/2006, à 02:29
- cabrito
Re : installation modem usb adsl : conceptronic CADSLUG version 1.0-12
Salut, il n'ya pas beaucoup d'infos sur le net au sujet de ton dongle, cela dit il en existe au moins un avec pour product ID: C11U, qui tourne avec un driver atmel.
Je ne sais pas si le tiens est semblable mais on peut toujours vérifier certaines choses.
Rebranche ton dongle et donne la sortie de dmesg et lsmod.
Et tant que t'y es celle de iwconfig.
Hors ligne
#3 Le 08/08/2006, à 12:01
- lautoine0
Re : installation modem usb adsl : conceptronic CADSLUG version 1.0-12
Merci de votre réponse, mais mon modem n'est oas un WiFi. Voici les renseignement dmesg et lsmod :
dsmeg :
buntu@ubuntu:~$ dmesg
[ 0.000000] Bootdata ok (command line is BOOT_IMAGE=/casper/vmlinuz boot=casp er initrd=/casper/initrd.gz ramdisk_size=1048576 root=/dev/ram rw quiet splash - - debian-installer/locale=fr kbd-chooser/method=be2-latin1)
[ 0.000000] Linux version 2.6.15-23-amd64-generic (buildd@yellow) (gcc versio n 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 SMP PREEMPT Tue May 23 13:45:47 UTC 2006
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 0000000037ff0000 (usable)
[ 0.000000] BIOS-e820: 0000000037ff0000 - 0000000037ff3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 0000000037ff3000 - 0000000038000000 (ACPI data)
[ 0.000000] BIOS-e820: 0000000038000000 - 0000000040000000 (reserved)
[ 0.000000] BIOS-e820: 00000000f0000000 - 00000000f2000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[ 0.000000] ACPI: RSDP (v000 GBT ) @ 0x0000 0000000f6bc0
[ 0.000000] ACPI: RSDT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x 0000000037ff3000
[ 0.000000] ACPI: FADT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x 0000000037ff3040
[ 0.000000] ACPI: MCFG (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x 0000000037ff7e80
[ 0.000000] ACPI: MADT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x 0000000037ff7e00
[ 0.000000] ACPI: DSDT (v001 GBT AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x 0000000000000000
[ 0.000000] Scanning NUMA topology in Northbridge 24
[ 0.000000] Number of nodes 1
[ 0.000000] Node 0 MemBase 0000000000000000 Limit 0000000037ff0000
[ 0.000000] Using 63 for the hash shift.
[ 0.000000] Using node hash shift of 63
[ 0.000000] Bootmem setup node 0 0000000000000000-0000000037ff0000
[ 0.000000] On node 0 totalpages: 225204
[ 0.000000] DMA zone: 3019 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 222185 pages, LIFO batch:31
[ 0.000000] Normal zone: 0 pages, LIFO batch:0
[ 0.000000] HighMem zone: 0 pages, LIFO batch:0
[ 0.000000] Nvidia board detected. Ignoring ACPI timer override.
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:15 APIC version 16
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] ACPI: IRQ14 used by override.
[ 0.000000] ACPI: IRQ15 used by override.
[ 0.000000] Setting APIC routing to physical flat
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:b000 0000)
[ 0.000000] Checking aperture...
[ 0.000000] CPU 0: aperture @ 582000000 size 32 MB
[ 0.000000] Aperture from northbridge cpu 0 too small (32 MB)
[ 0.000000] No AGP bridge found
[ 0.000000] SMP: Allowing 2 CPUs, 1 hotplug CPUs
[ 0.000000] Built 1 zonelists
[ 0.000000] Kernel command line: BOOT_IMAGE=/casper/vmlinuz boot=casper initr d=/casper/initrd.gz ramdisk_size=1048576 root=/dev/ram rw quiet splash -- debian -installer/locale=fr kbd-chooser/method=be2-latin1
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 131072 bytes)
[ 0.000000] time.c: Using 3.579545 MHz PM timer.
[ 0.000000] time.c: Detected 2009.207 MHz processor.
[ 52.936582] Console: colour VGA+ 80x25
[ 52.937196] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 52.938045] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 52.946413] Memory: 891424k/917440k available (2139k kernel code, 25628k rese rved, 754k data, 180k init)
[ 53.005708] Calibrating delay using timer specific routine.. 4022.49 BogoMIPS (lpj=2011246)
[ 53.005758] Security Framework v1.0.0 initialized
[ 53.005765] SELinux: Disabled at boot.
[ 53.005784] Mount-cache hash table entries: 256
[ 53.005884] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 53.005887] CPU: L2 Cache: 512K (64 bytes/line)
[ 53.005889] CPU 0(1) -> Node 0 -> Core 0
[ 53.005897] mtrr: v2.0 (20020519)
[ 53.005904] SMP alternatives: switching to UP code
[ 53.006175] checking if image is initramfs... it is
[ 53.583627] Freeing initrd memory: 7604k freed
[ 53.591288] ACPI: Looking for DSDT ... not found!
[ 53.605512] Using local APIC timer interrupts.
[ 53.655222] Detected 12.557 MHz APIC timer.
[ 53.655281] Brought up 1 CPUs
[ 53.655325] time.c: Using PIT/TSC based timekeeping.
[ 53.655327] testing NMI watchdog ... OK.
[ 53.665588] NET: Registered protocol family 16
[ 53.665611] ACPI: bus type pci registered
[ 53.665678] PCI: Using configuration type 1
[ 53.669143] PCI: Using MMCONFIG at f0000000
[ 53.669670] ACPI: Subsystem revision 20051216
[ 53.676685] ACPI: Interpreter enabled
[ 53.676687] ACPI: Using IOAPIC for interrupt routing
[ 53.677137] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 53.677140] PCI: Probing PCI hardware (bus 00)
[ 53.681276] Boot video device is 0000:00:05.0
[ 53.681908] PCI: Transparent bridge - 0000:00:10.0
[ 53.681928] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 53.784012] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[ 53.785496] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disa bled.
[ 53.785832] ACPI: PCI Interrupt Link [LNK2] (IRQs *5 7 9 10 11 14 15)
[ 53.786162] ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 *11 14 15)
[ 53.786489] ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disa bled.
[ 53.786823] ACPI: PCI Interrupt Link [LNK5] (IRQs 5 7 9 10 11 14 15) *0, disa bled.
[ 53.787160] ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 11 14 15) *0, disa bled.
[ 53.787490] ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 *11 14 15)
[ 53.787824] ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disa bled.
[ 53.788152] ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 *10 11 14 15)
[ 53.788477] ACPI: PCI Interrupt Link [LUBB] (IRQs 5 7 9 10 11 14 15) *0, disa bled.
[ 53.788814] ACPI: PCI Interrupt Link [LMAC] (IRQs *5 7 9 10 11 14 15)
[ 53.789143] ACPI: PCI Interrupt Link [LACI] (IRQs 5 7 9 10 11 14 15) *0, disa bled.
[ 53.789473] ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 *10 11 14 15)
[ 53.789805] ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disa bled.
[ 53.790134] ACPI: PCI Interrupt Link [LMCI] (IRQs 5 7 9 10 11 14 15) *0, disa bled.
[ 53.790462] ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 10 *11 14 15)
[ 53.790795] ACPI: PCI Interrupt Link [LUB2] (IRQs *5 7 9 10 11 14 15)
[ 53.791127] ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disa bled.
[ 53.791457] ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 10 *11 14 15)
[ 53.791791] ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 *10 11 14 15)
[ 53.792195] ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
[ 53.792596] ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
[ 53.792993] ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
[ 53.793389] ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
[ 53.793792] ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0, disabled.
[ 53.794188] ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled.
[ 53.794590] ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0, disabled.
[ 53.794984] ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.
[ 53.795381] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
[ 53.795783] ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
[ 53.796183] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
[ 53.796586] ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
[ 53.796982] ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.
[ 53.797382] ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0, disabled.
[ 53.797785] ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
[ 53.798184] ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
[ 53.798591] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
[ 53.798988] ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
[ 53.799387] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
[ 53.799790] ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
[ 53.800186] ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
[ 53.802723] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 53.802734] pnp: PnP ACPI init
[ 53.808399] pnp: PnP ACPI: found 11 devices
[ 53.808415] PCI: Using ACPI for IRQ routing
[ 53.808420] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 53.808535] PCI-DMA: Disabling IOMMU.
[ 53.809074] pnp: 00:00: ioport range 0x1000-0x107f could not be reserved
[ 53.809077] pnp: 00:00: ioport range 0x1080-0x10ff has been reserved
[ 53.809080] pnp: 00:00: ioport range 0x1400-0x147f has been reserved
[ 53.809083] pnp: 00:00: ioport range 0x1480-0x14ff could not be reserved
[ 53.809085] pnp: 00:00: ioport range 0x1800-0x187f has been reserved
[ 53.809088] pnp: 00:00: ioport range 0x1880-0x18ff has been reserved
[ 53.809091] pnp: 00:00: ioport range 0x2000-0x207f has been reserved
[ 53.809094] pnp: 00:00: ioport range 0x2080-0x20ff has been reserved
[ 53.809243] PCI: Bridge: 0000:00:10.0
[ 53.809246] IO window: 9000-afff
[ 53.809250] MEM window: f5000000-f50fffff
[ 53.809252] PREFETCH window: disabled.
[ 53.809262] PCI: Setting latency timer of device 0000:00:10.0 to 64
[ 53.809448] IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
[ 53.809710] audit: initializing netlink socket (disabled)
[ 53.809719] audit(1155035986.876:1): initialized
[ 53.809836] VFS: Disk quotas dquot_6.5.1
[ 53.809852] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 53.809897] Initializing Cryptographic API
[ 53.809900] io scheduler noop registered
[ 53.809909] io scheduler anticipatory registered
[ 53.809915] io scheduler deadline registered
[ 53.809927] io scheduler cfq registered
[ 53.821897] Real Time Clock Driver v1.12
[ 53.821932] Linux agpgart interface v0.101 (c) Dave Jones
[ 53.822012] PNP: PS/2 Controller [PNP0f13:PS2M] at 0x60,0x64 irq 12
[ 53.822014] PNP: PS/2 controller doesn't have KBD irq; using default 1
[ 54.383208] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 54.384692] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 54.384722] Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
[ 54.384840] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 54.386354] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 54.386917] ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
[ 54.386923] GSI 16 sharing vector 0xB1 and IRQ 16
[ 54.386926] ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [APC2] -> GSI 17 (lev el, low) -> IRQ 177
[ 54.387049] 0000:01:07.0: ttyS4 at I/O 0x9000 (irq = 177) is a 16550A
[ 54.387170] 0000:01:07.0: ttyS5 at I/O 0x9400 (irq = 177) is a 16550A
[ 54.387508] RAMDISK driver initialized: 16 RAM disks of 1048576K size 1024 bl ocksize
[ 54.387546] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 54.387549] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 54.387705] mice: PS/2 mouse device common for all mice
[ 54.397965] NET: Registered protocol family 2
[ 54.410040] IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 54.410280] TCP established hash table entries: 131072 (order: 9, 2097152 byt es)
[ 54.411535] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 54.412143] TCP: Hash tables configured (established 131072 bind 65536)
[ 54.412146] TCP reno registered
[ 54.412234] TCP bic registered
[ 54.412240] NET: Registered protocol family 1
[ 54.412247] NET: Registered protocol family 8
[ 54.412249] NET: Registered protocol family 20
[ 54.412389] ACPI wakeup devices:
[ 54.412391] HUB0 XVRA XVRB XVRC USB0 USB2 AZAD MMAC MMCI UAR1
[ 54.412396] ACPI: (supports S0 S1 S4 S5)
[ 54.412465] Freeing unused kernel memory: 180k freed
[ 54.480122] input: AT Translated Set 2 keyboard as /class/input/input0
[ 54.513441] vga16fb: initializing
[ 54.513446] vga16fb: mapped to 0xffff8100000a0000
[ 54.689083] Console: switching to colour frame buffer device 80x25
[ 54.689088] fb0: VGA16 VGA frame buffer device
[ 55.798095] Capability LSM initialized
[ 56.274473] SCSI subsystem initialized
[ 56.276170] ACPI: bus type scsi registered
[ 56.276174] libata version 1.20 loaded.
[ 56.277667] sata_nv 0000:00:0e.0: version 0.8
[ 56.278166] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23
[ 56.278172] GSI 17 sharing vector 0xB9 and IRQ 17
[ 56.278175] ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [APSI] -> GSI 23 (lev el, low) -> IRQ 185
[ 56.278301] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[ 56.278372] ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xD800 irq 185
[ 56.278391] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xD808 irq 185
[ 56.651429] ata1: dev 0 cfg 00:045a 49:2f00 82:346b 83:7fe9 84:4773 85:3468 8 6:3c01 87:4763 88:407f 93:0000
[ 56.651434] ata1: dev 0 ATA-7, max UDMA/133, 321670847 sectors: LBA48
[ 56.655627] sata_get_dev_handle: SATA dev addr=0xe0000, handle=0xffff810037fc 2dc0
[ 56.663195] ata1: dev 0 configured for UDMA/133
[ 56.667325] sata_get_dev_handle: SATA dev addr=0xe0000, handle=0xffff810037fc 2dc0
[ 56.674737] scsi0 : sata_nv
[ 56.875964] ata2: no device found (phy stat 00000000)
[ 56.875969] scsi1 : sata_nv
[ 56.876622] Vendor: ATA Model: HDT722516DLA380 Rev: V43O
[ 56.876631] Type: Direct-Access ANSI SCSI revision: 05
[ 56.877460] ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22
[ 56.877466] GSI 18 sharing vector 0xC1 and IRQ 18
[ 56.877469] ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [APSJ] -> GSI 22 (lev el, low) -> IRQ 193
[ 56.877576] PCI: Setting latency timer of device 0000:00:0f.0 to 64
[ 56.877628] ata3: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xC400 irq 193
[ 56.877648] ata4: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xC408 irq 193
[ 56.881485] Driver 'sd' needs updating - please use bus_type methods
[ 56.882233] SCSI device sda: 321670847 512-byte hdwr sectors (164695 MB)
[ 56.882249] SCSI device sda: drive cache: write back
[ 56.884915] SCSI device sda: 321670847 512-byte hdwr sectors (164695 MB)
[ 56.884931] SCSI device sda: drive cache: write back
[ 56.884936] sda: sda1 sda2 sda3 < sda5 sda6 sda7 >
[ 56.936516] sd 0:0:0:0: Attached scsi disk sda
[ 57.078697] ata3: no device found (phy stat 00000000)
[ 57.078702] scsi2 : sata_nv
[ 57.279431] ata4: no device found (phy stat 00000000)
[ 57.279436] scsi3 : sata_nv
[ 57.281088] NFORCE-MCP51: IDE controller at PCI slot 0000:00:0d.0
[ 57.281108] NFORCE-MCP51: chipset revision 161
[ 57.281110] NFORCE-MCP51: not 100% native mode: will probe irqs later
[ 57.281116] NFORCE-MCP51: 0000:00:0d.0 (rev a1) UDMA133 controller
[ 57.281124] ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DM A
[ 57.281134] ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DM A
[ 57.281141] Probing IDE interface ide0...
[ 57.544178] hda: Maxtor 6E040L0, ATA DISK drive
[ 58.257230] hdb: PLEXTOR DVDR PX-740A, ATAPI CD/DVD-ROM drive
[ 58.309656] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 58.317580] Probing IDE interface ide1...
[ 58.841869] hda: max request size: 128KiB
[ 58.847849] hda: Host Protected Area detected.
[ 58.847851] current capacity is 78154175 sectors (40014 MB)
[ 58.847853] native capacity is 78156288 sectors (40016 MB)
[ 58.851453] hda: Host Protected Area disabled.
[ 58.851456] hda: 78156288 sectors (40016 MB) w/2048KiB Cache, CHS=65535/16/63 , UDMA(133)
[ 58.851585] hda: cache flushes supported
[ 58.851722] hda: hda1
[ 58.869391] hdb: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33 )
[ 58.869400] Uniform CD-ROM driver Revision: 3.20
[ 59.127877] usbcore: registered new driver usbfs
[ 59.128143] usbcore: registered new driver hub
[ 59.129465] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Dri ver (PCI)
[ 59.130194] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 21
[ 59.130201] GSI 19 sharing vector 0xC9 and IRQ 19
[ 59.130204] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [APCF] -> GSI 21 (lev el, low) -> IRQ 201
[ 59.130320] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[ 59.130326] ohci_hcd 0000:00:0b.0: OHCI Host Controller
[ 59.144147] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus numbe r 1
[ 59.144159] ohci_hcd 0000:00:0b.0: irq 201, io mem 0xf5108000
[ 59.174946] forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0 .48.
[ 59.187463] ieee1394: Initialized config rom entry `ip1394'
[ 59.196976] hub 1-0:1.0: USB hub found
[ 59.196988] hub 1-0:1.0: 8 ports detected
[ 59.298987] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20
[ 59.298994] GSI 20 sharing vector 0xD1 and IRQ 20
[ 59.298997] ACPI: PCI Interrupt 0000:00:0b.1 -> Link [APCL] -> GSI 20 (lev el, low) -> IRQ 209
[ 59.299123] PCI: Setting latency timer of device 0000:00:0b.1 to 64
[ 59.299129] ehci_hcd 0000:00:0b.1: EHCI Host Controller
[ 59.299159] ehci_hcd 0000:00:0b.1: debug port 1
[ 59.299163] PCI: cache line size of 64 is not supported by device 0000:00:0b. 1
[ 59.299354] ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus numbe r 2
[ 59.299365] ehci_hcd 0000:00:0b.1: irq 209, io mem 0xf5104000
[ 59.299375] ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 59.299589] hub 2-0:1.0: USB hub found
[ 59.299597] hub 2-0:1.0: 8 ports detected
[ 59.401841] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23
[ 59.401846] ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [APCH] -> GSI 23 (lev el, low) -> IRQ 185
[ 59.401852] PCI: Setting latency timer of device 0000:00:14.0 to 64
[ 59.841044] ohci_hcd 0000:00:0b.0: wakeup
[ 59.914512] eth0: forcedeth.c: subsystem: 01458:e000 bound to 0000:00:14.0
[ 59.914995] ohci1394: $Rev: 1313 $ Ben Collins <bcollins@debian.org>
[ 59.915486] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
[ 59.915491] GSI 21 sharing vector 0xD9 and IRQ 21
[ 59.915494] ACPI: PCI Interrupt 0000:01:0e.0[A] -> Link [APC3] -> GSI 18 (lev el, low) -> IRQ 217
[ 59.915500] PCI: Via IRQ fixup for 0000:01:0e.0, from 11 to 9
[ 59.968837] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[217] MMIO=[f500000 0-f50007ff] Max Packet=[2048]
[ 59.984309] Probing IDE interface ide1...
[ 60.117663] usb 1-2: new full speed USB device using ohci_hcd and address 2
[ 60.485176] usb 1-3: new low speed USB device using ohci_hcd and address 3
[ 60.636568] usbcore: registered new driver hiddev
[ 60.649103] input: HID 1267:0103 as /class/input/input1
[ 60.649114] input: USB HID v1.10 Keyboard [HID 1267:0103] on usb-0000:00:0b.0 -3
[ 60.664057] input: HID 1267:0103 as /class/input/input2
[ 60.664062] input: USB HID v1.10 Device [HID 1267:0103] on usb-0000:00:0b.0-3
[ 60.664069] usbcore: registered new driver usbhid
[ 60.664071] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[ 61.230690] ieee1394: Host added: ID:BUS[0-00:1023] GUID[000014850036c5b1]
[ 65.986689] hdb: media error (bad sector): status=0x51 { DriveReady SeekCompl ete Error }
[ 65.986696] hdb: media error (bad sector): error=0x34 { AbortedCommand LastFa iledSense=0x03 }
[ 65.986699] ide: failed opcode was: unknown
[ 65.986704] end_request: I/O error, dev hdb, sector 1431336
[ 65.986708] Buffer I/O error on device hdb, logical block 357834
[ 72.146571] hdb: media error (bad sector): status=0x51 { DriveReady SeekCompl ete Error }
[ 72.146575] hdb: media error (bad sector): error=0x34 { AbortedCommand LastFa iledSense=0x03 }
[ 72.146578] ide: failed opcode was: unknown
[ 72.146580] end_request: I/O error, dev hdb, sector 1431336
[ 72.146583] Buffer I/O error on device hdb, logical block 357834
[ 78.412007] hdb: media error (bad sector): status=0x51 { DriveReady SeekCompl ete Error }
[ 78.412011] hdb: media error (bad sector): error=0x34 { AbortedCommand LastFa iledSense=0x03 }
[ 78.412014] ide: failed opcode was: unknown
[ 78.412016] end_request: I/O error, dev hdb, sector 1431336
[ 78.412019] Buffer I/O error on device hdb, logical block 357834
[ 84.690322] hdb: media error (bad sector): status=0x51 { DriveReady SeekCompl ete Error }
[ 84.690326] hdb: media error (bad sector): error=0x34 { AbortedCommand LastFa iledSense=0x03 }
[ 84.690329] ide: failed opcode was: unknown
[ 84.690332] end_request: I/O error, dev hdb, sector 1431336
[ 84.690334] Buffer I/O error on device hdb, logical block 357834
[ 90.966758] hdb: media error (bad sector): status=0x51 { DriveReady SeekCompl ete Error }
[ 90.966762] hdb: media error (bad sector): error=0x34 { AbortedCommand LastFa iledSense=0x03 }
[ 90.966765] ide: failed opcode was: unknown
[ 90.966767] end_request: I/O error, dev hdb, sector 1431336
[ 90.966770] Buffer I/O error on device hdb, logical block 357834
[ 97.259054] hdb: media error (bad sector): status=0x51 { DriveReady SeekCompl ete Error }
[ 97.259058] hdb: media error (bad sector): error=0x34 { AbortedCommand LastFa iledSense=0x03 }
[ 97.259061] ide: failed opcode was: unknown
[ 97.259063] end_request: I/O error, dev hdb, sector 1431336
[ 97.259066] Buffer I/O error on device hdb, logical block 357834
[ 100.803460] hdb: media error (bad sector): status=0x51 { DriveReady SeekCompl ete Error }
[ 100.803464] hdb: media error (bad sector): error=0x34 { AbortedCommand LastFa iledSense=0x03 }
[ 100.803467] ide: failed opcode was: unknown
[ 100.803470] end_request: I/O error, dev hdb, sector 1431328
[ 100.803472] Buffer I/O error on device hdb, logical block 357832
[ 104.040393] hdb: media error (bad sector): status=0x51 { DriveReady SeekCompl ete Error }
[ 104.040397] hdb: media error (bad sector): error=0x34 { AbortedCommand LastFa iledSense=0x03 }
[ 104.040400] ide: failed opcode was: unknown
[ 104.040402] end_request: I/O error, dev hdb, sector 1431332
[ 104.040405] Buffer I/O error on device hdb, logical block 357833
[ 107.277217] hdb: media error (bad sector): status=0x51 { DriveReady SeekCompl ete Error }
[ 107.277221] hdb: media error (bad sector): error=0x34 { AbortedCommand LastFa iledSense=0x03 }
[ 107.277224] ide: failed opcode was: unknown
[ 107.277226] end_request: I/O error, dev hdb, sector 1431328
[ 107.277229] Buffer I/O error on device hdb, logical block 357832
[ 110.514018] hdb: media error (bad sector): status=0x51 { DriveReady SeekCompl ete Error }
[ 110.514022] hdb: media error (bad sector): error=0x34 { AbortedCommand LastFa iledSense=0x03 }
[ 110.514025] ide: failed opcode was: unknown
[ 110.514027] end_request: I/O error, dev hdb, sector 1431332
[ 110.514030] Buffer I/O error on device hdb, logical block 357833
[ 110.930836] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 111.030116] ISO 9660 Extensions: RRIP_1991A
[ 111.125311] loop: loaded (max 8 devices)
[ 111.147200] Registering unionfs 1.1.2
[ 111.429766] squashfs: version 3.0prerelease (2006/1/24) Phillip Lougher
[ 212.713571] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 212.960354] eth0: no link during initialization.
[ 215.553091] ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 22
[ 215.553097] ACPI: PCI Interrupt 0000:00:10.1[b] -> Link [AAZA] -> GSI 22 (lev el, low) -> IRQ 193
[ 215.553221] PCI: Setting latency timer of device 0000:00:10.1 to 64
[ 215.719043] NET: Registered protocol family 17
[ 217.547667] input: PC Speaker as /class/input/input3
[ 217.827355] Floppy drive(s): fd0 is 1.44M
[ 217.830535] parport: PnPBIOS parport detected.
[ 217.830616] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE ,COMPAT,ECP,DMA]
[ 217.866612] FDC 0 is a post-1991 82077
[ 218.135566] input: ImPS/2 Generic Wheel Mouse as /class/input/input4
[ 218.198936] ts: Compaq touchscreen protocol output
[ 219.600789] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
[ 219.600793] md: bitmap version 4.39
[ 220.287826] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@red hat.com
[ 236.416922] ACPI: Power Button (FF) [PWRF]
[ 236.416932] ACPI: Power Button (CM) [PWRB]
[ 236.498798] ibm_acpi: ec object not found
[ 236.518174] pcc_acpi: loading...
[ 237.707643] powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.50.4)
[ 237.707759] powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x6 (1400 mV)
[ 237.707762] powernow-k8: 1 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV)
[ 237.707766] cpu_init done, current fid 0xc, vid 0x6
[ 257.374496] lp0: using parport0 (interrupt-driven).
[ 257.436035] ppdev: user-space parallel port driver
[ 272.396228] Bluetooth: Core ver 2.8
[ 272.396232] NET: Registered protocol family 31
[ 272.396234] Bluetooth: HCI device and connection manager initialized
[ 272.396242] Bluetooth: HCI socket layer initialized
[ 272.684288] Bluetooth: L2CAP ver 2.8
[ 272.684292] Bluetooth: L2CAP socket layer initialized
[ 272.887970] Bluetooth: RFCOMM socket layer initialized
[ 272.887983] Bluetooth: RFCOMM TTY layer initialized
[ 272.887985] Bluetooth: RFCOMM ver 1.7
[ 273.469328] NET: Registered protocol family 10
[ 273.469416] lo: Disabled Privacy Extensions
[ 273.469458] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 273.469479] IPv6 over IPv4 tunneling driver
ubuntu@ubuntu:~$
[b]comande lsmod :
Module Size Used by
ipv6 300416 8
rfcomm 45600 0
l2cap 30464 5 rfcomm
bluetooth 59268 4 rfcomm,l2cap
ppdev 11400 0
lp 15040 0
powernow_k8 12992 0
cpufreq_userspace 9184 1
cpufreq_stats 8264 0
freq_table 6464 2 powernow_k8,cpufreq_stats
cpufreq_powersave 3328 0
cpufreq_ondemand 9768 0
cpufreq_conservative 10984 0
video 18824 0
tc1100_wmi 9096 0
sony_acpi 7188 0
pcc_acpi 16128 0
hotkey 13768 0
dev_acpi 15364 0
container 6272 0
button 8864 0
acpi_sbs 24600 0
battery 12296 1 acpi_sbs
i2c_acpi_ec 7040 1 acpi_sbs
ac 7176 1 acpi_sbs
dm_mod 63176 1
md_mod 76792 0
tsdev 10240 0
parport_serial 10752 0
psmouse 40452 0
parport_pc 40944 2 parport_serial
floppy 74120 0
pcspkr 3592 0
parport 44172 3 ppdev,lp,parport_pc
af_packet 28172 2
snd_hda_intel 21664 1
snd_hda_codec 175048 1 snd_hda_intel
snd_pcm_oss 59424 0
snd_mixer_oss 20608 1 snd_pcm_oss
snd_pcm 104712 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss
snd_timer 29064 1 snd_pcm
serio_raw 9732 0
snd 68576 8 snd_hda_intel,snd_hda_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
soundcore 13216 1 snd
snd_page_alloc 13968 2 snd_hda_intel,snd_pcm
i2c_core 26624 1 i2c_acpi_ec
sg 43568 0
evdev 14464 3
squashfs 44416 1
unionfs 94232 1
loop 19216 2
nls_cp437 8320 1
isofs 39808 1
usbhid 42912 0
ide_generic 2816 0
ohci1394 37452 0
ieee1394 369688 1 ohci1394
forcedeth 27908 0
ehci_hcd 34568 0
ohci_hcd 23684 0
usbcore 145980 4 usbhid,ehci_hcd,ohci_hcd
ide_cd 35744 1
cdrom 41144 1 ide_cd
ide_disk 19456 1
generic 7300 0
amd74xx 16944 0 [permanent]
sd_mod 21504 1
sata_nv 12420 5
libata 86048 1 sata_nv
scsi_mod 160504 3 sg,sd_mod,libata
thermal 16524 0
processor 29224 2 powernow_k8,thermal
fan 6408 0
capability 7176 0
commoncap 9728 1 capability
vga16fb 15120 1
cfbcopyarea 5120 1 vga16fb
vgastate 10368 1 vga16fb
cfbimgblt 4224 1 vga16fb
cfbfillrect 5760 1 vga16fb
fbcon 43136 72
tileblit 4096 1 fbcon
font 9984 1 fbcon
bitblit 7424 1 fbcon
softcursor 3712 1 bitblit
ubuntu@ubuntu:~$
#4 Le 08/08/2006, à 12:56
- cabrito
Re : installation modem usb adsl : conceptronic CADSLUG version 1.0-12
Pourrais tu placer ton dmesg et ls mod entre des balises Code ,ça facilitera la lecture merci.
Vu que ce n'est pas un wifi il faudrait que tu donnes le résultat de la commande:
ifconfig
pour voir si ton interface réseau est bien montée dans quel cas il restera à la paraméter.
Hors ligne
#5 Le 09/08/2006, à 14:21
- lautoine0
Re : installation modem usb adsl : conceptronic CADSLUG version 1.0-12
Désolé pour la longeur de ma réponse, mais s'est la premières fois que j'utilise le forum, je ne sais pas quelle balise utilisé pour cela.
Je crois avoir résolu mon problème, j'ai trouvé le site :
http://eciadsl.flashtux.org/index.php
Le programme qu'ils ont conçu est développé pour le modem ECI Hifocus ADSL usb.
Dans une doc, ils indique que le drivers fonctionne avec les puces GolbeSpan GS 7070 et GS 7470; j'ai donc ouvert mon modem, celui-ci est constitué d'une puce GS 7070. En principe, le driver devrait être compatible.
Je vais donc installer leur package debian AMD64 :
http://eciadsl.flashtux.org/download.php
Merci pour votre aide.
#6 Le 09/08/2006, à 15:56
- cabrito
Re : installation modem usb adsl : conceptronic CADSLUG version 1.0-12
J'ai aussi fait une trouvaille intéressante.
En effet il existe un paquet nomé eciadsl dans la catégorie
réseau (universe)que tu peux installer avec synaptic ou bien
en ligne de commande: sudo apt-get install eciadsl
Il te faut évidemment avoir activés les dépôts universe.
Plus d'info:
http://packages.ubuntu.com/dapper/net/eciadsl
Donc a priori il y a là tout ce dont tu as besoin.
Dernière modification par cabrito (Le 09/08/2006, à 15:56)
Hors ligne