Ubuntu-fr

luria

Montage péripheriques USB edgy

Depuis le passage à Edgy, j'ai un problème avec les périphériques USB (disque dur externe, clefs, appareil photo) qui ne se montent plus. En tappant lsusb, j'obtiens :
Bus 003 Device 001: ID 0000:0000 
Bus 001 Device 001: ID 0000:0000 
Bus 002 Device 001: ID 0000:0000

ce qui semble confirmer que mes périphériques ne sont pas montés.

En lançant Gparted, je n'obtiens aucune information sur les périphériques, mais un message interessant : 

libparted : 1.7.1
automounting disabled

Il semble que le problème vienne de là, mais quelqu'un sait il comment le résoudre?

bruno59

Re : Montage péripheriques USB edgy

Salut

Même problème pour moi.
Si quelqu'un à une idée.

Par contre si je fais un dmesg | grep 'usb' j'obtient ceci

[17179580.868000] usbcore: registered new driver usbfs
[17179580.868000] usbcore: registered new driver hub
[17179580.960000] usb usb1: configuration #1 chosen from 1 choice
[17179581.568000]  <f88f1854> usb_hcd_irq+0x24/0x60 [usbcore]  <c0149323> handle_IRQ_event+0x33/0x60
[17179581.568000] [<f88f1830>] (usb_hcd_irq+0x0/0x60 [usbcore])
[17179581.628000] usb usb2: configuration #1 chosen from 1 choice
[17179581.736000] usb usb3: configuration #1 chosen from 1 choice
[17179582.508000] usb 3-7: new high speed USB device using ehci_hcd and address 3
[17179594.052000] usb 3-7: device not accepting address 3, error -110
[17179594.164000] usb 3-7: new high speed USB device using ehci_hcd and address 4
[17179605.708000] usb 3-7: device not accepting address 4, error -110
[17179605.820000] usb 3-7: new high speed USB device using ehci_hcd and address 5
[17179616.244000] usb 3-7: device not accepting address 5, error -110
[17179616.356000] usb 3-7: new high speed USB device using ehci_hcd and address 6
[17179626.780000] usb 3-7: device not accepting address 6, error -110
[17179775.880000] usb 3-5: new high speed USB device using ehci_hcd and address 7
[17179787.424000] usb 3-5: device not accepting address 7, error -110
[17179787.536000] usb 3-5: new high speed USB device using ehci_hcd and address 8
[17179799.080000] usb 3-5: device not accepting address 8, error -110
[17179799.192000] usb 3-5: new high speed USB device using ehci_hcd and address 9
[17179809.616000] usb 3-5: device not accepting address 9, error -110
[17179809.728000] usb 3-5: new high speed USB device using ehci_hcd and address 10
[17179820.152000] usb 3-5: device not accepting address 10, error -110
[17180149.616000] usb 3-5: new high speed USB device using ehci_hcd and address 11
[17180161.160000] usb 3-5: device not accepting address 11, error -110
[17180161.272000] usb 3-5: new high speed USB device using ehci_hcd and address 12
[17180172.816000] usb 3-5: device not accepting address 12, error -110
[17180172.928000] usb 3-5: new high speed USB device using ehci_hcd and address 13
[17180183.352000] usb 3-5: device not accepting address 13, error -110
[17180183.464000] usb 3-5: new high speed USB device using ehci_hcd and address 14
[17180193.888000] usb 3-5: device not accepting address 14, error -110

---

Le blog de Nono : http://nono.bevrard.org

bruno59

Re : Montage péripheriques USB edgy

Bon aprés recherche sur google cela semblerai venir du noyau et de l'usb2
Je vais donc patienter un peu pour voir si la prochaine version du noyau corrige ce probleme.

---

Le blog de Nono : http://nono.bevrard.org

Xarkam

Re : Montage péripheriques USB edgy

Idem pour moi pour mon disque dur usb, mais ma clé usb se monte.

xarkam@HYKSOS:~$ dmesg | grep usb
[17179579.652000] usbcore: registered new driver usbfs
[17179579.652000] usbcore: registered new driver hub
[17179579.788000] usb usb1: configuration #1 chosen from 1 choice
[17179579.896000] usb usb2: configuration #1 chosen from 1 choice
[17179580.632000] usb 1-4: new full speed USB device using ohci_hcd and address 2
[17179580.872000] usb 1-4: configuration #1 chosen from 1 choice
[17179592.708000] drivers/usb/class/usblp.c: Disabling reads from problem bidirectional printer on usblp0
[17179592.716000] drivers/usb/class/usblp.c: usblp0: USB Unidirectional printer dev 2 if 0 alt 1 proto 2 vid 0x03F0 pid 0x0104
[17179592.716000] usbcore: registered new driver usblp
[17179592.716000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[17179737.488000] usb 2-2: new high speed USB device using ehci_hcd and address 3
[17179738.008000] usb 2-2: device not accepting address 3, error -71
[17179738.120000] usb 2-2: new high speed USB device using ehci_hcd and address 4
[17179738.456000] usb 2-2: configuration #1 chosen from 1 choice
[17179738.636000] usbcore: registered new driver libusual
[17179738.704000] usb-storage: device found at 4
[17179738.704000] usb-storage: waiting for device to settle before scanning
[17179738.704000] usbcore: registered new driver usb-storage
[17179743.708000] usb-storage: device scan complete
[17179743.820000] usb 2-2: reset high speed USB device using ehci_hcd and address 4
[17179743.952000] usb 2-2: device descriptor read/all, error -71
[17179744.068000] usb 2-2: reset high speed USB device using ehci_hcd and address 4
[17179744.404000] usb 2-2: can't restore configuration #1 (error=-71)
[17179744.404000] usb 2-2: USB disconnect, address 4
[17179744.520000] usb 2-2: new high speed USB device using ehci_hcd and address 5
[17179745.040000] usb 2-2: device not accepting address 5, error -71
[17179745.152000] usb 2-2: new high speed USB device using ehci_hcd and address 6
[17179745.672000] usb 2-2: device not accepting address 6, error -71
[17179745.784000] usb 2-2: new high speed USB device using ehci_hcd and address 7
[17179746.008000] usb 2-2: unable to read config index 0 descriptor/start
[17179746.008000] usb 2-2: can't read configurations, error -71
[17179746.124000] usb 2-2: new high speed USB device using ehci_hcd and address 8
[17179746.532000] usb 2-2: device not accepting address 8, error -71
[17179785.872000] usb 2-2: new high speed USB device using ehci_hcd and address 9
[17179786.392000] usb 2-2: device not accepting address 9, error -71
[17179786.504000] usb 2-2: new high speed USB device using ehci_hcd and address 10
[17179786.616000] usb 2-2: device descriptor read/64, error -71
[17179787.240000] usb 2-2: device not accepting address 10, error -71
[17179787.352000] usb 2-2: new high speed USB device using ehci_hcd and address 11
[17179787.760000] usb 2-2: device not accepting address 11, error -71
[17179787.872000] usb 2-2: new high speed USB device using ehci_hcd and address 12
[17179788.280000] usb 2-2: device not accepting address 12, error -71
[17179811.324000] usb 2-1: new high speed USB device using ehci_hcd and address 13
[17179812.312000] usb 2-1: new high speed USB device using ehci_hcd and address 14
[17179813.300000] usb 2-1: new high speed USB device using ehci_hcd and address 15
[17179813.708000] usb 2-1: device not accepting address 15, error -71
[17179813.820000] usb 2-1: new high speed USB device using ehci_hcd and address 16
[17179814.228000] usb 2-1: device not accepting address 16, error -71
[17179888.436000] usb 2-1: new high speed USB device using ehci_hcd and address 17
[17179888.552000] usb 2-1: device descriptor read/64, error -71
[17179889.644000] usb 2-1: new high speed USB device using ehci_hcd and address 18
[17179889.760000] usb 2-1: device descriptor read/64, error -71
[17179890.852000] usb 2-1: new high speed USB device using ehci_hcd and address 19
[17179891.260000] usb 2-1: device not accepting address 19, error -71
[17179891.372000] usb 2-1: new high speed USB device using ehci_hcd and address 20
[17179891.780000] usb 2-1: device not accepting address 20, error -71
[17179933.040000] usb 2-1: new high speed USB device using ehci_hcd and address 21
[17179933.152000] usb 2-1: device descriptor read/64, error -71
[17179933.368000] usb 2-1: device descriptor read/64, error -71
[17179933.584000] usb 2-1: new high speed USB device using ehci_hcd and address 22
[17179933.696000] usb 2-1: device descriptor read/64, error -71
[17179934.784000] usb 2-1: new high speed USB device using ehci_hcd and address 23
[17179935.192000] usb 2-1: device not accepting address 23, error -71
[17179935.304000] usb 2-1: new high speed USB device using ehci_hcd and address 24
[17179935.712000] usb 2-1: device not accepting address 24, error -71

Dernière modification par Xarkam (Le 01/11/2006, à 12:32)

---

Osames Manager
---
Asus Rampage V Extrême | Intel i7 5820K | Corsair 16GB DDR4 | NVIDIA GeForce 770GTX
Utilisateur d'Ubuntu, Debian, et Windows

Xarkam

Re : Montage péripheriques USB edgy

Bon, après une pléthores de manipulation il fonctionne mon disque dur usb.

---

Osames Manager
---
Asus Rampage V Extrême | Intel i7 5820K | Corsair 16GB DDR4 | NVIDIA GeForce 770GTX
Utilisateur d'Ubuntu, Debian, et Windows

lune001

Re : Montage péripheriques USB edgy

Bon pareil pour moi, sauf que totu est reconnu, en fait y'a plus d'automount (pourtant bien coche dans gnome-volume-properties).
Le lsusb / et dmesg m'indique pour pas de souci particulier ?
Des idées ?

bruno59

Re : Montage péripheriques USB edgy

Bon, après une pléthores de manipulation il fonctionne mon disque dur usb.

Salut

C est possible de savoir quelles manipulations

---

Le blog de Nono : http://nono.bevrard.org

bruno59

Re : Montage péripheriques USB edgy

J'ai trouvé une solution qui fonctionne chez moi

Ajouter le parametre usb-handoff dans grub

title        Ubuntu, kernel 2.6.17-10-generic
root        (hd0,0)
kernel        /boot/vmlinuz-2.6.17-10-generic root=UUID=9a8bcc92-96c5-4033-b25d-d69622ebfcb9 ro quiet splash usb-handoff
initrd        /boot/initrd.img-2.6.17-10-generic
savedefault
boot

mes disques et cle usb refonctionne

---

Le blog de Nono : http://nono.bevrard.org