Ubuntu-fr

Crone123

Hostapd: Faire fonctionner du Wifi N a 450Mb/s?

Bonjour,
J'ai acheté une carte Wifi N en PCI-Express capable de fournir 450Mb/s en double bande.

J'aimerais que le point Wifi crée (a usage de routeur) ait la vitesse maximale de la carte.
Je ne connais pas trop le détail technique de tous les modes disponibles, et en fonction de ce que je règle j'arrive a avoir entre rien, une connexion très basse (1Mb/s) et une connexion plus rapide: 150Mb/s

Sauf que 150Mb/s c'est seulement 1/3 de la puissance de la carte...

En sachant que la carte a 3 antennes, et que son détail est:

valentin@ACER-VALENTIN4:~$ iw list
Wiphy phy0
	Band 1:
		Capabilities: 0x11ef
			RX LDPC
			HT20/HT40
			SM Power Save disabled
			RX HT20 SGI
			RX HT40 SGI
			TX STBC
			RX STBC 1-stream
			Max AMSDU length: 3839 bytes
			DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 8 usec (0x06)
		HT TX/RX MCS rate indexes supported: 0-23
		Frequencies:
			* 2412 MHz [1] (20.0 dBm)
			* 2417 MHz [2] (20.0 dBm)
			* 2422 MHz [3] (20.0 dBm)
			* 2427 MHz [4] (20.0 dBm)
			* 2432 MHz [5] (20.0 dBm)
			* 2437 MHz [6] (20.0 dBm)
			* 2442 MHz [7] (20.0 dBm)
			* 2447 MHz [8] (20.0 dBm)
			* 2452 MHz [9] (20.0 dBm)
			* 2457 MHz [10] (20.0 dBm)
			* 2462 MHz [11] (20.0 dBm)
			* 2467 MHz [12] (20.0 dBm)
			* 2472 MHz [13] (20.0 dBm)
			* 2484 MHz [14] (disabled)
		Bitrates (non-HT):
			* 1.0 Mbps
			* 2.0 Mbps (short preamble supported)
			* 5.5 Mbps (short preamble supported)
			* 11.0 Mbps (short preamble supported)
			* 6.0 Mbps
			* 9.0 Mbps
			* 12.0 Mbps
			* 18.0 Mbps
			* 24.0 Mbps
			* 36.0 Mbps
			* 48.0 Mbps
			* 54.0 Mbps
	Band 2:
		Capabilities: 0x11ef
			RX LDPC
			HT20/HT40
			SM Power Save disabled
			RX HT20 SGI
			RX HT40 SGI
			TX STBC
			RX STBC 1-stream
			Max AMSDU length: 3839 bytes
			DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 8 usec (0x06)
		HT TX/RX MCS rate indexes supported: 0-23
		Frequencies:
			* 5180 MHz [36] (23.0 dBm)
			* 5200 MHz [40] (23.0 dBm)
			* 5220 MHz [44] (23.0 dBm)
			* 5240 MHz [48] (23.0 dBm)
			* 5260 MHz [52] (23.0 dBm) (passive scanning, no IBSS, radar detection)
			* 5280 MHz [56] (23.0 dBm) (passive scanning, no IBSS, radar detection)
			* 5300 MHz [60] (23.0 dBm) (passive scanning, no IBSS, radar detection)
			* 5320 MHz [64] (23.0 dBm) (passive scanning, no IBSS, radar detection)
			* 5500 MHz [100] (disabled)
			* 5520 MHz [104] (disabled)
			* 5540 MHz [108] (disabled)
			* 5560 MHz [112] (disabled)
			* 5580 MHz [116] (disabled)
			* 5600 MHz [120] (disabled)
			* 5620 MHz [124] (disabled)
			* 5640 MHz [128] (disabled)
			* 5660 MHz [132] (disabled)
			* 5680 MHz [136] (disabled)
			* 5700 MHz [140] (disabled)
			* 5745 MHz [149] (30.0 dBm)
			* 5765 MHz [153] (30.0 dBm)
			* 5785 MHz [157] (30.0 dBm)
			* 5805 MHz [161] (30.0 dBm)
			* 5825 MHz [165] (30.0 dBm)
		Bitrates (non-HT):
			* 6.0 Mbps
			* 9.0 Mbps
			* 12.0 Mbps
			* 18.0 Mbps
			* 24.0 Mbps
			* 36.0 Mbps
			* 48.0 Mbps
			* 54.0 Mbps
	max # scan SSIDs: 4
	max scan IEs length: 2257 bytes
	Coverage class: 0 (up to 0m)
	Supported Ciphers:
		* WEP40 (00-0f-ac:1)
		* WEP104 (00-0f-ac:5)
		* TKIP (00-0f-ac:2)
		* CCMP (00-0f-ac:4)
		* CMAC (00-0f-ac:6)
	Available Antennas: TX 0x7 RX 0x7
	Configured Antennas: TX 0x7 RX 0x7
	Supported interface modes:
		 * IBSS
		 * managed
		 * AP
		 * AP/VLAN
		 * WDS
		 * monitor
		 * mesh point
		 * P2P-client
		 * P2P-GO
	software interface modes (can always be added):
		 * AP/VLAN
		 * monitor
	interface combinations are not supported
	Supported commands:
		 * new_interface
		 * set_interface
		 * new_key
		 * new_beacon
		 * new_station
		 * new_mpath
		 * set_mesh_params
		 * set_bss
		 * authenticate
		 * associate
		 * deauthenticate
		 * disassociate
		 * join_ibss
		 * join_mesh
		 * remain_on_channel
		 * set_tx_bitrate_mask
		 * action
		 * frame_wait_cancel
		 * set_wiphy_netns
		 * set_channel
		 * set_wds_peer
		 * connect
		 * disconnect
	Supported TX frame types:
		 * IBSS: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0
		 * managed: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0
		 * AP: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0
		 * AP/VLAN: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0
		 * mesh point: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0
		 * P2P-client: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0
		 * P2P-GO: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0
	Supported RX frame types:
		 * IBSS: 0x00d0
		 * managed: 0x0040 0x00d0
		 * AP: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0
		 * AP/VLAN: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0
		 * mesh point: 0x00b0 0x00c0 0x00d0
		 * P2P-client: 0x0040 0x00d0
		 * P2P-GO: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0
	Device supports RSN-IBSS.

J'utilise une sécurité en WPA-PSK:

interface=wlan1
ssid=mon_ssid
driver=nl80211
logger_syslog=-1
logger_syslog_level=2
logger_stdout=-1
logger_stdout_level=2
hw_mode=g
ieee80211n=1
wme_enabled=1
ht_capab=[SHORT-GI-20][SHORT-GI-40][64-QAM][TX-HT20-SGI][RX-HT20-SGI][TX-HT40-SGI][RX-HT40-SGI][DSSS_CCK-40][MAX-AMSDU-3839][RX-STBC1][RX-LDPC]
channel=13
wpa=1
auth_algs=1
wpa_passphrase=ma_clé
wpa_key_mgmt=WPA-PSK
wpa_pairwise=CCMP
rsn_pairwise=CCMP

J'ai choisi le canal 13 parce que c'est le seul qui fonctionne chez moi. Je suis obligé de l'utiliser a cause d'une sonnette sans fil qui brouille tous les autres canaux

Quelqu'un pourrait me modifier mon fichier de config initial avec les bonnes options pour que la carte utilise du 450mb/s? Et si possible m'expliquer ce qui n'allait pas?
Merci