Ubuntu-fr

ulysse4807

installation carte tuner

Bonjour, je suis débutant sous kubuntu. Je cherche un moyen de visionner la tv sur mon PC (avec une pinnacle pctv rave). J'ai installé plusieurs programmes, dont tvtime, qui me dit quand je le lance en mode console:
              -"~/Desktop/bttv-0.9.14$ sudo tvtime
Utilise tvtime 1.0.2.
Lit la configuration depuis /etc/tvtime/tvtime.xml
Lit la configuration depuis /home/ulysse/.tvtime/tvtime.xml
xvoutput: No XVIDEO port found which supports YUY2 images.

*** tvtime requires hardware YUY2 overlay support from your video card
*** driver.  If you are using an older NVIDIA card (TNT2), then
*** this capability is only available with their binary drivers.
*** For some ATI cards, this feature may be found in the experimental
*** GATOS drivers: http://gatos.souceforge.net/
*** If unsure, please check with your distribution to see if your
*** X driver supports hardware overlay surfaces."

               -quand je fais lspci ma carte a l'air détectée (brooktree bt878): "~/Desktop/bttv-0.9.14$ lspci
00:00.0 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge
00:00.1 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge
00:00.2 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge
00:00.3 Host bridge: VIA Technologies, Inc. PT890 Host Bridge
00:00.4 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge
00:00.7 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge
00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge
00:0a.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
00:0a.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
00:0b.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
00:0f.0 IDE interface: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80)
00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South]
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 78)
01:00.0 VGA compatible controller: ATI Technologies Inc RV350 AP [Radeon 9600]
01:00.1 Display controller: ATI Technologies Inc RV350 AP [Radeon 9600] (Secondary)"

           - Bon je m'suis dit quand même que ça pouvait être un problème de pilotes: J'ai essayé d'installer les drivers bttv mais je n'y arrive pas. Je télécharge l'archive tar.bz, je la décompresse, je me place dans le dossier décompressé, j'ouvre un terminal: "~/Desktop/bttv-0.9.14$ ./configure
bash: ./configure: Aucun fichier ou répertoire de ce type
ulysse@bryner:~/Desktop/bttv-0.9.14$ make
make -C /lib/modules/2.6.22-14-generic/build SUBDIRS=/home/ulysse/Desktop/bttv-0.9.14 modules
make[1]: Entering directory `/usr/src/linux-headers-2.6.22-14-generic'
  CC [M]  /home/ulysse/Desktop/bttv-0.9.14/video-buf.o
/home/ulysse/Desktop/bttv-0.9.14/video-buf.c:46: error: expected ')' before string constant
make[2]: *** [/home/ulysse/Desktop/bttv-0.9.14/video-buf.o] Error 1
make[1]: *** [_module_/home/ulysse/Desktop/bttv-0.9.14] Error 2
make[1]: Leaving directory `/usr/src/linux-headers-2.6.22-14-generic'
make: *** [default] Erreur 2
ulysse@bryner:~/Desktop/bttv-0.9.14$ make install
strip --strip-debug video-buf.o v4l1-compat.o v4l2-common.o btcx-risc.o ir-common.o bttv.o ir-common.o tuner.o tda9887.o msp3400.o tvaudio.o tvmixer.o
strip: 'video-buf.o': No such file
strip: 'v4l1-compat.o': No such file
strip: 'v4l2-common.o': No such file
strip: 'btcx-risc.o': No such file
strip: 'ir-common.o': No such file
strip: 'bttv.o': No such file
strip: 'ir-common.o': No such file
strip: 'tuner.o': No such file
strip: 'tda9887.o': No such file
strip: 'msp3400.o': No such file
strip: 'tvaudio.o': No such file
strip: 'tvmixer.o': No such file
make: *** [install] Erreur 1"

Voilà  voilà , j'comprends pas grands chose à  tout ce charabia. Donc en gros je souhaiterais savoir s'il existe un moyen assez facile de regarder la tv sous mon kubuntu (s'il existe un dépà´t qui centralise tous les pilotes et les lecteurs tv, je suis preneur). Accessoirement, y-a-il une méthode infaillible pour installer les fichiers compris dans les archives tar/gz/que sais-je encore (Je n'ai pas trouvé d'informations d'installation dans les readmes de bttv)?

Je nage dans la glue. Tendez moi la main par pitié! Merci d'avance pour votre aide

ulysse4807

Re : installation carte tuner

Bon en fait j'ai tapé dmesg | grep bttv dans la konsole et voilà  ce que ça fait:

"ulysse@bryner:~$ v0: Bt878 (rev 17) at 0000:00:0a.0, irq: 19, latency: 32, mmio: 0xf7ffe000
bash: erreur de syntaxe près du jeton `(' inattendu
ulysse@bryner:~$ [   14.104000] bttv0: detected: Pinnacle PCTV [card=39], PCI subsystem ID is 11bd:0012
bash: [: "]" manquant
ulysse@bryner:~$ [   14.104000] bttv0: using: Pinnacle PCTV Studio/Rave [card=39,autodetected]
bash: [: "]" manquant
ulysse@bryner:~$ [   14.104000] bttv0: gpio: en=00000000, out=00000000 in=00ff63ff [init]
bash: [: "]" manquant
ulysse@bryner:~$ [   14.104000] bttv0: i2c: checking for MSP34xx @ 0x80... <6>pci_hotplug: PCI Hot Plug PCI Core version: 0.5
bash: erreur de syntaxe près du jeton `6' inattendu
ulysse@bryner:~$ [   14.692000] bttv0: miro: id=24 tuner=3 radio=no stereo=no
bash: [: "]" manquant
ulysse@bryner:~$ [   14.692000] bttv0: using tuner=3
bash: [: "]" manquant
ulysse@bryner:~$ [   14.692000] bttv0: i2c: checking for MSP34xx @ 0x80... not found
bash: [: "]" manquant
ulysse@bryner:~$ [   14.692000] bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bash: [: "]" manquant
ulysse@bryner:~$ [   14.692000] bttv0: i2c: checking for TDA7432 @ 0x8a... not found
bash: [: "]" manquant
ulysse@bryner:~$ [   14.692000] bttv0: i2c: checking for TDA9887 @ 0x86... not found
bash: [: "]" manquant
ulysse@bryner:~$ dmesg | grep bttv
[   14.104000] bttv: driver version 0.9.17 loaded
[   14.104000] bttv: using 8 buffers with 2080k (520 pages) each for capture
[   14.104000] bttv: Bt8xx card found (0).
[   14.104000] bttv0: Bt878 (rev 17) at 0000:00:0a.0, irq: 19, latency: 32, mmio: 0xf7ffe000
[   14.104000] bttv0: detected: Pinnacle PCTV [card=39], PCI subsystem ID is 11bd:0012
[   14.104000] bttv0: using: Pinnacle PCTV Studio/Rave [card=39,autodetected]
[   14.104000] bttv0: gpio: en=00000000, out=00000000 in=00ff63ff [init]
[   14.104000] bttv0: i2c: checking for MSP34xx @ 0x80... <6>pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   14.692000] bttv0: miro: id=24 tuner=3 radio=no stereo=no
[   14.692000] bttv0: using tuner=3
[   14.692000] bttv0: i2c: checking for MSP34xx @ 0x80... not found
[   14.692000] bttv0: i2c: checking for TDA9875 @ 0xb0... not found
[   14.692000] bttv0: i2c: checking for TDA7432 @ 0x8a... not found
[   14.692000] bttv0: i2c: checking for TDA9887 @ 0x86... not found
[   15.268000] bttv0: registered device video0ulysse@bryner:~$ v0: Bt878 (rev 17) at 0000:00:0a.0, irq: 19, latency: 32, mmio: 0xf7ffe000
bash: erreur de syntaxe près du jeton `(' inattendu
ulysse@bryner:~$ [   14.104000] bttv0: detected: Pinnacle PCTV [card=39], PCI subsystem ID is 11bd:0012
bash: [: "]" manquant
ulysse@bryner:~$ [   14.104000] bttv0: using: Pinnacle PCTV Studio/Rave [card=39,autodetected]
bash: [: "]" manquant
ulysse@bryner:~$ [   14.104000] bttv0: gpio: en=00000000, out=00000000 in=00ff63ff [init]
bash: [: "]" manquant
ulysse@bryner:~$ [   14.104000] bttv0: i2c: checking for MSP34xx @ 0x80... <6>pci_hotplug: PCI Hot Plug PCI Core version: 0.5
bash: erreur de syntaxe près du jeton `6' inattendu
ulysse@bryner:~$ [   14.692000] bttv0: miro: id=24 tuner=3 radio=no stereo=no
bash: [: "]" manquant
ulysse@bryner:~$ [   14.692000] bttv0: using tuner=3
bash: [: "]" manquant
ulysse@bryner:~$ [   14.692000] bttv0: i2c: checking for MSP34xx @ 0x80... not found
bash: [: "]" manquant
ulysse@bryner:~$ [   14.692000] bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bash: [: "]" manquant
ulysse@bryner:~$ [   14.692000] bttv0: i2c: checking for TDA7432 @ 0x8a... not found
bash: [: "]" manquant
ulysse@bryner:~$ [   14.692000] bttv0: i2c: checking for TDA9887 @ 0x86... not found
bash: [: "]" manquant
ulysse@bryner:~$ dmesg | grep bttv
[   14.104000] bttv: driver version 0.9.17 loaded
[   14.104000] bttv: using 8 buffers with 2080k (520 pages) each for capture
[   14.104000] bttv: Bt8xx card found (0).
[   14.104000] bttv0: Bt878 (rev 17) at 0000:00:0a.0, irq: 19, latency: 32, mmio: 0xf7ffe000
[   14.104000] bttv0: detected: Pinnacle PCTV [card=39], PCI subsystem ID is 11bd:0012
[   14.104000] bttv0: using: Pinnacle PCTV Studio/Rave [card=39,autodetected]
[   14.104000] bttv0: gpio: en=00000000, out=00000000 in=00ff63ff [init]
[   14.104000] bttv0: i2c: checking for MSP34xx @ 0x80... <6>pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   14.692000] bttv0: miro: id=24 tuner=3 radio=no stereo=no
[   14.692000] bttv0: using tuner=3
[   14.692000] bttv0: i2c: checking for MSP34xx @ 0x80... not found
[   14.692000] bttv0: i2c: checking for TDA9875 @ 0xb0... not found
[   14.692000] bttv0: i2c: checking for TDA7432 @ 0x8a... not found
[   14.692000] bttv0: i2c: checking for TDA9887 @ 0x86... not found
[   15.268000] bttv0: registered device video0
[   15.268000] bttv0: registered device vbi0
[   15.268000] bttv0: PLL: 28636363 => 35468950 .. ok
[ 4046.564000] bttv0: PLL can sleep, using XTAL (28636363).
[ 4046.748000] bttv0: PLL: 28636363 => 35468950 .. ok
[ 4096.152000] bttv0: PLL can sleep, using XTAL (28636363).
[ 4096.288000] bttv0: PLL: 28636363 => 35468950 .. ok

[   15.268000] bttv0: registered device vbi0
[   15.268000] bttv0: PLL: 28636363 => 35468950 .. ok
[ 4046.564000] bttv0: PLL can sleep, using XTAL (28636363).
[ 4046.748000] bttv0: PLL: 28636363 => 35468950 .. ok
[ 4096.152000] bttv0: PLL can sleep, using XTAL (28636363).
[ 4096.288000] bttv0: PLL: 28636363 => 35468950 .. ok"

Ca veut dire que les drivers bttv sont installés? Ce serait déjà  une bonne chose, non?