Pages : 1
#1 Le 28/11/2014, à 01:30
- auron3351
Disque dur interne endommagé
Bonjour, je suis sous Lubuntu 14.04 sur un Acer Aspire 5715z et je me suis rendu compte que j'avais mon disque dur interne endommagé... J'ai donc lancé la commande:
~$ sudo smartctl -a /dev/sda #
Et voilà ce que j'obtiens:
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Scorpio Blue Serial ATA
Device Model: WDC WD1600BEVS-22RST0
Serial Number: WD-WXEX07F37740
LU WWN Device Id: 5 0014ee 255fad2c8
Firmware Version: 04.01G04
User Capacity: 160 041 885 696 bytes [160 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-7 (minor revision not indicated)
Local Time is: Fri Nov 28 00:02:16 2014 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 121) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: ( 7200) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 92) minutes.
Conveyance self-test routine
recommended polling time: ( 6) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0003 186 160 021 Pre-fail Always - 1658
4 Start_Stop_Count 0x0032 095 095 000 Old_age Always - 5011
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 100 253 051 Pre-fail Always - 0
9 Power_On_Hours 0x0032 077 077 000 Old_age Always - 16838
10 Spin_Retry_Count 0x0013 100 100 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0012 100 100 051 Old_age Always - 0
12 Power_Cycle_Count 0x0032 096 096 000 Old_age Always - 4669
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 641
193 Load_Cycle_Count 0x0032 104 104 000 Old_age Always - 288069
194 Temperature_Celsius 0x0022 104 090 000 Old_age Always - 43
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 1
198 Offline_Uncorrectable 0x0010 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0009 100 253 051 Pre-fail Offline - 0
SMART Error Log Version: 1
ATA Error Count: 12 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 12 occurred at disk power-on lifetime: 16131 hours (672 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 e0 a0 30 40 Error: UNC at LBA = 0x0030a0e0 = 3186912
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 d0 f8 a0 30 12 08 00:30:03.430 READ FPDMA QUEUED
60 08 c8 f0 a0 30 12 08 00:30:03.430 READ FPDMA QUEUED
60 08 b8 e8 a0 30 12 08 00:30:03.430 READ FPDMA QUEUED
60 08 b0 e0 a0 30 12 08 00:30:03.430 READ FPDMA QUEUED
60 08 a8 d8 a0 30 12 08 00:30:03.429 READ FPDMA QUEUED
Error 11 occurred at disk power-on lifetime: 16131 hours (672 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 e0 a0 30 40 Error: UNC at LBA = 0x0030a0e0 = 3186912
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 b8 00 a1 30 12 08 00:29:59.959 READ FPDMA QUEUED
60 00 b0 00 a0 30 12 08 00:29:59.954 READ FPDMA QUEUED
60 00 a8 00 9f 30 12 08 00:29:59.948 READ FPDMA QUEUED
60 00 a0 00 9e 30 12 08 00:29:59.941 READ FPDMA QUEUED
60 00 98 00 9d 30 12 08 00:29:59.936 READ FPDMA QUEUED
Error 10 occurred at disk power-on lifetime: 15721 hours (655 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 e0 a0 30 40 Error: UNC at LBA = 0x0030a0e0 = 3186912
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 e0 f8 a0 30 12 08 01:22:05.759 READ FPDMA QUEUED
60 08 d8 f0 a0 30 12 08 01:22:05.759 READ FPDMA QUEUED
60 08 c8 e8 a0 30 12 08 01:22:05.759 READ FPDMA QUEUED
60 08 c0 e0 a0 30 12 08 01:22:05.759 READ FPDMA QUEUED
60 08 b8 d8 a0 30 12 08 01:22:05.759 READ FPDMA QUEUED
Error 9 occurred at disk power-on lifetime: 15721 hours (655 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 e0 a0 30 40 Error: UNC at LBA = 0x0030a0e0 = 3186912
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 c0 00 a0 30 12 08 01:22:02.724 READ FPDMA QUEUED
60 00 b8 00 9f 30 12 08 01:22:02.719 READ FPDMA QUEUED
60 00 b0 00 9e 30 12 08 01:22:02.714 READ FPDMA QUEUED
60 00 a8 00 9d 30 12 08 01:22:02.708 READ FPDMA QUEUED
60 00 a0 00 9c 30 12 08 01:22:02.703 READ FPDMA QUEUED
Error 8 occurred at disk power-on lifetime: 15495 hours (645 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 e0 a0 30 40 Error: UNC at LBA = 0x0030a0e0 = 3186912
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 b0 e0 a0 30 12 08 01:26:39.524 READ FPDMA QUEUED
60 80 a8 00 bb 71 04 08 01:26:39.524 READ FPDMA QUEUED
61 08 a0 e8 4b 04 09 08 01:26:39.524 WRITE FPDMA QUEUED
ea 00 00 00 00 00 00 08 01:26:39.498 FLUSH CACHE EXT
61 28 90 c0 4b 04 09 08 01:26:39.498 WRITE FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed: read failure 90% 16838 305176800
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Est-il possible de réparer tout cela..?
Par avance, merci.
Hors ligne
#2 Le 28/11/2014, à 04:59
- moko138
Re : Disque dur interne endommagé
Ton disque a 17.000 heures de vol et 1 "Current_Pending_Sector".
Il était à 43°C au moment de ton test.
1) Cela veut dire qu'il est prudent de le remplacer rapidement. Avant que son usure ne s'aggrave et que la conservation de tes données ne devienne ardue, voire en partie impossible.
Pour plus de sûreté des mesures, redonne les données SMART à partir d'une session live, mais il est probable que le secteur défectueux ne sera pas récupéré. Et il est certain que d'autres vont suivre.
2) Par ailleurs, quand tu auras changé ton disque n'oublie de surveiller sa température et de modifier, si besoin, ses réglages pour qu'il ne dépasse pas 40°.
A titre d'exemple, j'ai quasiment le même disque que le tien, et si j'oublie de lancer au démarrage :
sudo hdparm -B 240 /dev/sda
sa température peut monter à 55° (et je n'ai pas flashplayer qui échauffe les disques).
Mais quand je lance cette commande, qu'il est possible d'automatiser, la température ne dépasse pas 41 °C, même en utilisation intensive.
Les têtes de lectures de ton disque, pendant sa vie, ne se sont mises au repos que toutes les 6 minutes en moyenne, d'où l'échauffement. (chez moi : 1 minute).
Plus de détails dans cette page de doc : https://doc.ubuntu-fr.org/laptop_mode et dans
man hdparm
%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel : À la découverte de dcraw
Hors ligne
Pages : 1