Pages : 1
#1 Le 15/04/2015, à 22:33
- driverack
erreur ffado dbus server
bonjour, je suis nouveau sur UBUNTU STUDIO 14.04.
J'aimerais traiter de l'audio en temps réel(ou presque) en duplex avec une carte son ECHO AUDIOFIRE12 via JACK et FFADO mais jusqu'a maintenant, c'est simple, rien ne marche.
A l'ouverture de FFADO MIXER :"logginghandler: Could not communicate with the FFADO DBus service..."
A l'ouverture de ECHOMIXER (installer automatiquement lors de l'installation de STUDIO): c'est simple, pas d'ouverture
A l'ouverture de JACKCTL:
21:53:42.105 Baie de brassage activée.
21:53:42.106 Réinitialisation des statistiques.
21:53:42.138 Changement des connexions ALSA.
21:53:42.164 DBUS : le service n'est pas disponible (org.jackaudio.service soit jackdbus).
21:53:42.200 Changement du graphique des connexions ALSA.
(qjackctl:4587): Gtk-CRITICAL **: IA__gtk_widget_get_direction: assertion 'GTK_IS_WIDGET (widget)' failed
(qjackctl:4587): Gtk-CRITICAL **: IA__gtk_widget_get_direction: assertion 'GTK_IS_WIDGET (widget)' failed
21:53:42.399 Balayage de la baie de brassage ALSA active...
J'ai manifestement un problème de DBUS mais impossible pour moi de le résoudre.
Voici ce que donne un ffado-diag:
=== CHECK ===
Base system...
kernel version............ 3.16.0-33-lowlatency
Preempt (low latency)... True
RT patched.............. False
old 1394 stack present.... False
old 1394 stack loaded..... False
old 1394 stack active..... False
new 1394 stack present.... True
new 1394 stack loaded..... True
new 1394 stack active..... True
/dev/raw1394 node present. False
/dev/fw* permissions:
crw------- 1 root root 250, 0 avril 7 20:29 /dev/fw0
crw-rw----+ 1 root audio 250, 1 avril 7 20:29 /dev/fw1
User IDs:
uid=1000(gilles) gid=1000(gilles) groupes=1000(gilles),4(adm),24(cdrom),27(sudo),29(audio),30(dip),46(plugdev),108(lpadmin),123(sambashare)
Prerequisites (dynamic at run-time)...
gcc ............... gcc (Ubuntu 4.8.2-19ubuntu1) 4.8.2
g++ ............... g++ (Ubuntu 4.8.2-19ubuntu1) 4.8.2
PyQt4 (by pyuic4) . Python User Interface Compiler 4.10.4 for Qt version 4.8.6
jackd ............. no message buffer overruns
path ............ /usr/bin/jackd
flags ........... -ljack
libraw1394 ........ 2.1.0
flags ........... -lraw1394
libavc1394 ........ 0.5.4
flags ........... -lavc1394 -lrom1394 -lraw1394
libiec61883 ....... 1.2.0
flags ........... -liec61883 -lraw1394
libxml++-2.6 ...... 2.36.0
flags ........... -I/usr/include/libxml2 -I/usr/include/glibmm-2.4 -I/usr/lib/x86_64-linux-gnu/glibmm-2.4/include -I/usr/include/sigc++-2.0 -I/usr/lib/x86_64-linux-gnu/sigc++-2.0/include -I/usr/include/glib-2.0 -I/usr/lib/x86_64-linux-gnu/glib-2.0/include -I/usr/include/libxml++-2.6 -I/usr/lib/libxml++-2.6/include -lxml++-2.6 -lxml2 -lglibmm-2.4 -lgobject-2.0 -lsigc-2.0 -lglib-2.0
dbus-1 ............ 1.6.18
flags ........... -I/usr/include/dbus-1.0 -I/usr/lib/x86_64-linux-gnu/dbus-1.0/include -ldbus-1
Prerequisites (static at compile-time)...
gcc ............... gcc (Ubuntu/Linaro 4.8.2-1ubuntu1) 4.8.2
g++ ............... g++ (Ubuntu/Linaro 4.8.2-1ubuntu1) 4.8.2
PyQt4 (by pyuic4) . Python User Interface Compiler 4.10.3 for Qt version 4.8.4
jackd ............. sh: 1: jackd: not found
path ............
flags ........... Package jack was not found in the pkg-config search path.
libraw1394 ........ 2.1.0
flags ........... -lraw1394
libavc1394 ........ Package libavc1394 was not found in the pkg-config search path.
flags ........... Package libavc1394 was not found in the pkg-config search path.
libiec61883 ....... 1.2.0
flags ........... -liec61883 -lraw1394
libxml++-2.6 ...... 2.36.0
flags ........... -I/usr/include/libxml2 -I/usr/include/glibmm-2.4 -I/usr/lib/x86_64-linux-gnu/glibmm-2.4/include -I/usr/include/sigc++-2.0 -I/usr/lib/x86_64-linux-gnu/sigc++-2.0/include -I/usr/include/glib-2.0 -I/usr/lib/x86_64-linux-gnu/glib-2.0/include -I/usr/include/libxml++-2.6 -I/usr/lib/libxml++-2.6/include -lxml++-2.6 -lxml2 -lglibmm-2.4 -lgobject-2.0 -lsigc-2.0 -lglib-2.0
dbus-1 ............ 1.6.12
flags ........... -I/usr/include/dbus-1.0 -I/usr/lib/x86_64-linux-gnu/dbus-1.0/include -ldbus-1
uname -a...
Linux FILTRAGEACTIF 3.16.0-33-lowlatency #44~14.04.1-Ubuntu SMP PREEMPT Fri Mar 13 10:51:41 UTC 2015 x86_64 x86_64 x86_64 GNU/Linux
Hardware...
Host controllers:
05:02.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link) [104c:8024] (prog-if 10 [OHCI])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at f7c04000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at f7c00000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
CPU info:
Architecture: x86_64
Mode(s) opératoire(s) des processeurs :32-bit, 64-bit
Byte Order: Little Endian
CPU(s): 8
On-line CPU(s) list: 0-7
Thread(s) par cœur : 2
Cœur(s) par socket : 4
Socket(s): 1
Nœud(s) NUMA : 1
Identifiant constructeur :GenuineIntel
Famille de processeur :6
Modèle : 60
Révision : 3
Vitesse du processeur en MHz :3563.300
BogoMIPS: 7348.62
Virtualisation : VT-x
Cache L1d : 32K
Cache L1i : 32K
Cache L2 : 256K
Cache L3 : 8192K
NUMA node0 CPU(s): 0-7
Configuration...
IRQ information
Hardware Interrupts:
--------------------
IRQ 0: PID: None, count: [28, 0, 0, 0, 0, 0, 0, 0], Sched None (priority None), drivers: ['timer']
IRQ 1: PID: None, count: [3, 0, 0, 0, 0, 0, 0, 0], Sched None (priority None), drivers: ['i8042']
IRQ 8: PID: None, count: [1, 0, 0, 0, 0, 0, 0, 0], Sched None (priority None), drivers: ['rtc0']
IRQ 9: PID: None, count: [0, 0, 0, 0, 0, 0, 3, 0], Sched None (priority None), drivers: ['acpi']
IRQ 12: PID: None, count: [2, 0, 0, 1, 0, 1, 0, 0], Sched None (priority None), drivers: ['i8042']
IRQ 17: PID: None, count: [848, 7, 163, 155, 516, 2, 8, 6], Sched None (priority None), drivers: ['firewire_ohci']
IRQ 19: PID: None, count: [2888, 169, 804, 13605, 349, 1070, 784, 58514], Sched None (priority None), drivers: ['ata_piix']
IRQ 20: PID: None, count: [22, 0, 1, 0, 0, 10, 0, 0], Sched None (priority None), drivers: ['ehci_hcd:usb1']
IRQ 23: PID: None, count: [21, 0, 0, 3, 4, 0, 9, 0], Sched None (priority None), drivers: ['ehci_hcd:usb2']
IRQ 41: PID: None, count: [21, 10049, 9, 0, 235, 193363, 702, 524], Sched None (priority None), drivers: ['xhci_hcd']
IRQ 42: PID: None, count: [17, 6, 85085, 4, 4, 4, 4, 0], Sched None (priority None), drivers: ['eth0']
IRQ 43: PID: None, count: [3, 0, 0, 0, 0, 3, 0, 6], Sched None (priority None), drivers: ['mei_me']
IRQ 44: PID: None, count: [1427, 425, 805, 410, 666, 409, 381, 440], Sched None (priority None), drivers: ['i915']
Software Interrupts:
--------------------
=== REPORT ===
FireWire kernel drivers:
The new FireWire kernel stack is loaded.
If running a kernel earlier than 2.6.37 and problems are experienced, either
try with the old Firewire kernel stack or upgrade to a newer kernel
(preferrably 2.6.37 or later).
gilles@FILTRAGEACTIF:~$
Si quelqu'un pouvait m'aider à trouver la solution, ce serait super.
Ils manque certainement des renseignements mais, je ne sais pas exactement lesquels.
Ils y a plusieurs post sur les ECHO AUDIOFIRE mais les solutions proposées ne fonctionnent pas chez moi ou je ne peux pas les appliquer (ligne de cde inexistante par exemple)
par avance, merci beaucoup
Gilles
Dernière modification par driverack (Le 16/04/2015, à 22:45)
Hors ligne
Pages : 1