Pages : 1
#1 Le 21/09/2016, à 15:00
- wido
[résolu] smartctl disque dur samsung
Bonjour, je viens de faire un smartctl avec le programme GSmartControl et j'ai une alerte sur l'un de mes disques dur:
smartctl 6.5 2016-05-07 r4318 [x86_64-linux-4.7.4-1-ARCH] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint F3
Device Model: SAMSUNG HD103SJ
Serial Number: S246J1LZ407350
LU WWN Device Id: 5 0024e9 0034dd99c
Firmware Version: 1AJ10001
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Wed Sep 21 14:55:27 2016 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 9300) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 155) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 051 Pre-fail Always - 0
2 Throughput_Performance 0x0026 252 252 000 Old_age Always - 0
3 Spin_Up_Time 0x0023 070 068 025 Pre-fail Always - 9179
4 Start_Stop_Count 0x0032 098 098 000 Old_age Always - 3019
5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 252 252 051 Old_age Always - 0
8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 14206
10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 1
12 Power_Cycle_Count 0x0032 097 097 000 Old_age Always - 3079
191 G-Sense_Error_Rate 0x0022 100 100 000 Old_age Always - 854
192 Power-Off_Retract_Count 0x0022 252 252 000 Old_age Always - 0
194 Temperature_Celsius 0x0002 064 056 000 Old_age Always - 32 (Min/Max 15/44)
195 Hardware_ECC_Recovered 0x003a 100 100 000 Old_age Always - 0
196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 252 252 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0036 100 100 000 Old_age Always - 218
200 Multi_Zone_Error_Rate 0x002a 100 100 000 Old_age Always - 330
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 1
225 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 3082
SMART Error Log Version: 1
ATA Error Count: 7 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 7 occurred at disk power-on lifetime: 8294 hours (345 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 08 00:00:00.039 IDENTIFY DEVICE
00 00 01 01 00 00 00 08 00:00:00.039 NOP [Abort queued commands]
ec 00 00 00 00 00 a0 08 00:00:00.034 IDENTIFY DEVICE
27 00 00 00 00 00 e0 08 00:00:00.034 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 08 00:00:00.034 IDENTIFY DEVICE
Error 6 occurred at disk power-on lifetime: 8294 hours (345 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 08 00:00:00.034 IDENTIFY DEVICE
27 00 00 00 00 00 e0 08 00:00:00.034 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 08 00:00:00.034 IDENTIFY DEVICE
00 00 01 01 00 00 40 08 00:00:00.033 NOP [Abort queued commands]
25 00 01 00 00 00 e0 08 00:00:00.031 READ DMA EXT
Error 5 occurred at disk power-on lifetime: 8294 hours (345 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 08 00:00:00.034 IDENTIFY DEVICE
ec 00 00 00 00 00 a0 08 00:00:00.034 IDENTIFY DEVICE
00 00 01 01 00 00 40 08 00:00:00.033 NOP [Abort queued commands]
25 00 01 00 00 00 e0 08 00:00:00.031 READ DMA EXT
c6 00 01 00 00 00 e0 08 00:00:00.025 SET MULTIPLE MODE
Error 4 occurred at disk power-on lifetime: 8294 hours (345 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec ff 01 01 00 00 e0 00 00:00:00.015 IDENTIFY DEVICE
a1 ff 01 01 00 00 e0 00 00:00:00.014 IDENTIFY PACKET DEVICE
Error 3 occurred at disk power-on lifetime: 8294 hours (345 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 08 00:00:00.066 IDENTIFY DEVICE
ec 00 00 00 00 00 a0 08 00:00:00.066 IDENTIFY DEVICE
00 00 00 00 00 00 00 00 00:00:00.066 NOP [Abort queued commands]
60 00 08 00 00 00 40 00 00:00:00.000 READ FPDMA QUEUED
60 00 08 00 00 00 40 00 00:00:00.034 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed [00% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.j'en sais trop rien
Dernière modification par wido (Le 27/09/2016, à 14:48)
Hors ligne
#2 Le 23/09/2016, à 16:49
- Bougron
Re : [résolu] smartctl disque dur samsung
Bonjour.
Peux-tu indiquer exactement le message que tu as?
Es-tu sur que c'est ce disque?
Hors ligne
#3 Le 23/09/2016, à 22:17
- wido
Re : [résolu] smartctl disque dur samsung
j'ai 3 disques dur et c'est le seul qui me met en alerte
ATA Error Count: 7 (Note: Usually only the last five errors are stored.)
Complete error log:
SMART Error Log Version: 1
ATA Error Count: 7 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 7 occurred at disk power-on lifetime: 8294 hours (345 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 08 00:00:00.039 IDENTIFY DEVICE
00 00 01 01 00 00 00 08 00:00:00.039 NOP [Abort queued commands]
ec 00 00 00 00 00 a0 08 00:00:00.034 IDENTIFY DEVICE
27 00 00 00 00 00 e0 08 00:00:00.034 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 08 00:00:00.034 IDENTIFY DEVICE
Error 6 occurred at disk power-on lifetime: 8294 hours (345 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 08 00:00:00.034 IDENTIFY DEVICE
27 00 00 00 00 00 e0 08 00:00:00.034 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 08 00:00:00.034 IDENTIFY DEVICE
00 00 01 01 00 00 40 08 00:00:00.033 NOP [Abort queued commands]
25 00 01 00 00 00 e0 08 00:00:00.031 READ DMA EXT
Error 5 occurred at disk power-on lifetime: 8294 hours (345 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 08 00:00:00.034 IDENTIFY DEVICE
ec 00 00 00 00 00 a0 08 00:00:00.034 IDENTIFY DEVICE
00 00 01 01 00 00 40 08 00:00:00.033 NOP [Abort queued commands]
25 00 01 00 00 00 e0 08 00:00:00.031 READ DMA EXT
c6 00 01 00 00 00 e0 08 00:00:00.025 SET MULTIPLE MODE
Error 4 occurred at disk power-on lifetime: 8294 hours (345 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec ff 01 01 00 00 e0 00 00:00:00.015 IDENTIFY DEVICE
a1 ff 01 01 00 00 e0 00 00:00:00.014 IDENTIFY PACKET DEVICE
Error 3 occurred at disk power-on lifetime: 8294 hours (345 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 08 00:00:00.066 IDENTIFY DEVICE
ec 00 00 00 00 00 a0 08 00:00:00.066 IDENTIFY DEVICE
00 00 00 00 00 00 00 00 00:00:00.066 NOP [Abort queued commands]
60 00 08 00 00 00 40 00 00:00:00.000 READ FPDMA QUEUED
60 00 08 00 00 00 40 00 00:00:00.034 READ FPDMA QUEUEDDernière modification par wido (Le 23/09/2016, à 22:18)
Hors ligne
#4 Le 23/09/2016, à 22:35
- moko138
Re : [résolu] smartctl disque dur samsung
8294 hours ce n'est pas sda, qui a dépassé les 14.000 heures.
%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel : À la découverte de dcraw
Hors ligne
#5 Le 23/09/2016, à 22:43
- Bougron
Re : [résolu] smartctl disque dur samsung
Bonsoir.
Pas d'inquiétude à avoir. Le logiciel te previent qu'il y a eu un incident sur ce disque dans le passé. On peut simplement se demander pourquoi il a attendu tant de temps pour le faire! ( 14206 - 8294) heures.
Donnes le retour de smartctl pour les deux autres disques au cas ou il se tromperait.
Dernière modification par Bougron (Le 23/09/2016, à 22:49)
Hors ligne
#6 Le 23/09/2016, à 23:08
- wido
Re : [résolu] smartctl disque dur samsung
SSD
smartctl 6.5 2016-05-07 r4318 [x86_64-linux-4.7.4-1-ARCH] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Indilinx Barefoot_2/Everest/Martini based SSDs
Device Model: OCZ-AGILITY4
Serial Number: OCZ-8HT3990HR0041JX0
LU WWN Device Id: 5 e83a97 cc055d380
Firmware Version: 1.5.2
User Capacity: 128,035,676,160 bytes [128 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Fri Sep 23 23:07:14 2016 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x1d) SMART execute Offline immediate.
No Auto Offline data collection support.
Abort Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x00) Error logging NOT supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 0) minutes.
Extended self-test routine
recommended polling time: ( 0) minutes.
SMART Attributes Data Structure revision number: 18
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x0000 006 000 000 Old_age Offline - 6
3 Spin_Up_Time 0x0000 100 100 000 Old_age Offline - 0
4 Start_Stop_Count 0x0000 100 100 000 Old_age Offline - 0
5 Reallocated_Sector_Ct 0x0000 100 100 000 Old_age Offline - 0
9 Power_On_Hours 0x0000 100 100 000 Old_age Offline - 5503
12 Power_Cycle_Count 0x0000 100 100 000 Old_age Offline - 1536
232 Lifetime_Writes 0x0000 100 100 000 Old_age Offline - 9875804434
233 Media_Wearout_Indicator 0x0000 099 000 000 Old_age Offline - 99
SMART Error Log not supported
Warning! SMART Self-Test Log Structure error: invalid SMART checksum.
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Selective Self-tests/Logging not supportedHDD 1To:
smartctl 6.5 2016-05-07 r4318 [x86_64-linux-4.7.4-1-ARCH] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Black
Device Model: WDC WD1002FAEX-00Y9A0
Serial Number: WD-WCAW32664754
LU WWN Device Id: 5 0014ee 2061dd2fc
Firmware Version: 05.01D05
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Fri Sep 23 23:07:50 2016 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (16380) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 169) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 2
3 Spin_Up_Time 0x0027 171 167 021 Pre-fail Always - 4433
4 Start_Stop_Count 0x0032 098 098 000 Old_age Always - 2441
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 085 085 000 Old_age Always - 11130
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 098 098 000 Old_age Always - 2437
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 266
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 2174
194 Temperature_Celsius 0x0022 118 112 000 Old_age Always - 29
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 199 000 Old_age Always - 19
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.Hors ligne
#7 Le 24/09/2016, à 07:05
- moko138
Re : [résolu] smartctl disque dur samsung
Là, ce sont deux autres disques ;
l'un à 5.503 heures,
l'autre à 11.130 heures.
Pour que le forum puisse t'aider vite et bien, prends l'habitude d'inclure les 2 prompts et la commande (ici ..."dev/sdx") dans tous tes retours.
Et de ne pas couper les retours.
%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel : À la découverte de dcraw
Hors ligne
#8 Le 24/09/2016, à 16:35
- wido
Re : [résolu] smartctl disque dur samsung
$ sudo smartctl -a /dev/sda
smartctl 6.5 2016-05-07 r4318 [x86_64-linux-4.7.4-1-ARCH] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Indilinx Barefoot_2/Everest/Martini based SSDs
Device Model: OCZ-AGILITY4
Serial Number: OCZ-8HT3990HR0041JX0
LU WWN Device Id: 5 e83a97 cc055d380
Firmware Version: 1.5.2
User Capacity: 128 035 676 160 bytes [128 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Sat Sep 24 16:33:44 2016 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x1d) SMART execute Offline immediate.
No Auto Offline data collection support.
Abort Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x00) Error logging NOT supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 0) minutes.
Extended self-test routine
recommended polling time: ( 0) minutes.
SMART Attributes Data Structure revision number: 18
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x0000 006 000 000 Old_age Offline - 6
3 Spin_Up_Time 0x0000 100 100 000 Old_age Offline - 0
4 Start_Stop_Count 0x0000 100 100 000 Old_age Offline - 0
5 Reallocated_Sector_Ct 0x0000 100 100 000 Old_age Offline - 0
9 Power_On_Hours 0x0000 100 100 000 Old_age Offline - 5509
12 Power_Cycle_Count 0x0000 100 100 000 Old_age Offline - 1538
232 Lifetime_Writes 0x0000 100 100 000 Old_age Offline - 9879718366
233 Media_Wearout_Indicator 0x0000 099 000 000 Old_age Offline - 99
SMART Error Log not supported
Warning! SMART Self-Test Log Structure error: invalid SMART checksum.
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Selective Self-tests/Logging not supported$ sudo smartctl -a /dev/sdb
smartctl 6.5 2016-05-07 r4318 [x86_64-linux-4.7.4-1-ARCH] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint F3
Device Model: SAMSUNG HD103SJ
Serial Number: S246J1LZ407350
LU WWN Device Id: 5 0024e9 0034dd99c
Firmware Version: 1AJ10001
User Capacity: 1 000 204 886 016 bytes [1,00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Sat Sep 24 16:34:14 2016 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 9300) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 155) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 051 Pre-fail Always - 0
2 Throughput_Performance 0x0026 252 252 000 Old_age Always - 0
3 Spin_Up_Time 0x0023 070 068 025 Pre-fail Always - 9178
4 Start_Stop_Count 0x0032 098 098 000 Old_age Always - 3024
5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 252 252 051 Old_age Always - 0
8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 14237
10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 1
12 Power_Cycle_Count 0x0032 097 097 000 Old_age Always - 3084
191 G-Sense_Error_Rate 0x0022 100 100 000 Old_age Always - 854
192 Power-Off_Retract_Count 0x0022 252 252 000 Old_age Always - 0
194 Temperature_Celsius 0x0002 064 056 000 Old_age Always - 31 (Min/Max 15/44)
195 Hardware_ECC_Recovered 0x003a 100 100 000 Old_age Always - 0
196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 252 252 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0036 100 100 000 Old_age Always - 218
200 Multi_Zone_Error_Rate 0x002a 100 100 000 Old_age Always - 330
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 1
225 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 3087
SMART Error Log Version: 1
ATA Error Count: 7 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 7 occurred at disk power-on lifetime: 8294 hours (345 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 08 00:00:00.039 IDENTIFY DEVICE
00 00 01 01 00 00 00 08 00:00:00.039 NOP [Abort queued commands]
ec 00 00 00 00 00 a0 08 00:00:00.034 IDENTIFY DEVICE
27 00 00 00 00 00 e0 08 00:00:00.034 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 08 00:00:00.034 IDENTIFY DEVICE
Error 6 occurred at disk power-on lifetime: 8294 hours (345 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 08 00:00:00.034 IDENTIFY DEVICE
27 00 00 00 00 00 e0 08 00:00:00.034 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 08 00:00:00.034 IDENTIFY DEVICE
00 00 01 01 00 00 40 08 00:00:00.033 NOP [Abort queued commands]
25 00 01 00 00 00 e0 08 00:00:00.031 READ DMA EXT
Error 5 occurred at disk power-on lifetime: 8294 hours (345 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 08 00:00:00.034 IDENTIFY DEVICE
ec 00 00 00 00 00 a0 08 00:00:00.034 IDENTIFY DEVICE
00 00 01 01 00 00 40 08 00:00:00.033 NOP [Abort queued commands]
25 00 01 00 00 00 e0 08 00:00:00.031 READ DMA EXT
c6 00 01 00 00 00 e0 08 00:00:00.025 SET MULTIPLE MODE
Error 4 occurred at disk power-on lifetime: 8294 hours (345 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec ff 01 01 00 00 e0 00 00:00:00.015 IDENTIFY DEVICE
a1 ff 01 01 00 00 e0 00 00:00:00.014 IDENTIFY PACKET DEVICE
Error 3 occurred at disk power-on lifetime: 8294 hours (345 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 08 00:00:00.066 IDENTIFY DEVICE
ec 00 00 00 00 00 a0 08 00:00:00.066 IDENTIFY DEVICE
00 00 00 00 00 00 00 00 00:00:00.066 NOP [Abort queued commands]
60 00 08 00 00 00 40 00 00:00:00.000 READ FPDMA QUEUED
60 00 08 00 00 00 40 00 00:00:00.034 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 14206 -
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed [00% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.$ sudo smartctl -a /dev/sdc
smartctl 6.5 2016-05-07 r4318 [x86_64-linux-4.7.4-1-ARCH] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Black
Device Model: WDC WD1002FAEX-00Y9A0
Serial Number: WD-WCAW32664754
LU WWN Device Id: 5 0014ee 2061dd2fc
Firmware Version: 05.01D05
User Capacity: 1 000 204 886 016 bytes [1,00 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Sat Sep 24 16:34:49 2016 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (16380) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 169) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 2
3 Spin_Up_Time 0x0027 170 167 021 Pre-fail Always - 4458
4 Start_Stop_Count 0x0032 098 098 000 Old_age Always - 2442
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 085 085 000 Old_age Always - 11138
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 098 098 000 Old_age Always - 2438
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 266
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 2175
194 Temperature_Celsius 0x0022 116 112 000 Old_age Always - 31
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 199 000 Old_age Always - 19
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.Hors ligne
#9 Le 26/09/2016, à 19:37
- Bougron
Re : [résolu] smartctl disque dur samsung
Bonjour
Tes trois disques sont en bon état.
Hors ligne
#10 Le 27/09/2016, à 14:48
- wido
Hors ligne