Ubuntu-fr

Baba1986

accès après formatage à disque dur Western Digital Elements

Bonjour et merci pour vos lumières,
J'ai  pensé bien faire en formatant en NTFS mon nouveau DD western Digital Elements mais depuis je ne le voit plus...
voici ce que le terminal me dit d'après les demandes de renseignements de discussions précédentes

jessica@jessica:~$ Isusb
La commande « Isusb » est introuvable, vouliez-vous dire :
 La commande « lsusb » du paquet « usbutils » (main)
Isusb : commande introuvable
jessica@jessica:~$ lsusb
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 006 Device 002: ID 148f:2000 Ralink Technology, Corp. 
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 174f:1134 Syntek 
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 004: ID 1058:10b8 Western Digital Technologies, Inc. Elements Portable (WDBU6Y, WDBUZG)
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 002: ID 062a:4101 Creative Labs Wireless Keyboard/Mouse
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
jessica@jessica:~$ dmesg | tail -n 30
[   34.617808] wlo1: associate with 7a:04:32:69:25:0c (try 1/3)
[   34.626829] wlo1: RX AssocResp from 7a:04:32:69:25:0c (capab=0x411 status=0 aid=2)
[   34.626954] wlo1: associated
[   34.627054] IPv6: ADDRCONF(NETDEV_CHANGE): wlo1: link becomes ready
[   44.978665] Bluetooth: RFCOMM TTY layer initialized
[   44.978690] Bluetooth: RFCOMM socket layer initialized
[   44.978702] Bluetooth: RFCOMM ver 1.11
[  166.002442] ieee80211 phy0: rt2x00queue_flush_queue: Warning - Queue 2 failed to flush
[  166.514405] ieee80211 phy0: rt2x00queue_flush_queue: Warning - Queue 2 failed to flush
[  417.332803] usb 1-2: USB disconnect, device number 3
[  424.717119] usb 1-2: new high-speed USB device number 4 using ehci-pci
[  424.908188] usb 1-2: New USB device found, idVendor=1058, idProduct=10b8
[  424.908206] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[  424.908216] usb 1-2: Product: Elements 10B8
[  424.908225] usb 1-2: Manufacturer: Western Digital
[  424.908233] usb 1-2: SerialNumber: 5758323141363639504B344C
[  424.912138] usb-storage 1-2:1.0: USB Mass Storage device detected
[  424.914995] scsi host2: usb-storage 1-2:1.0
[  425.915577] scsi 2:0:0:0: Direct-Access     WD       Elements 10B8    1021 PQ: 0 ANSI: 6
[  425.920526] sd 2:0:0:0: Attached scsi generic sg1 type 0
[  425.928383] sd 2:0:0:0: [sdb] Spinning up disk...
[  426.932730] .....ready
[  430.970257] sd 2:0:0:0: [sdb] 1953458176 512-byte logical blocks: (1.00 TB/931 GiB)
[  430.973674] sd 2:0:0:0: [sdb] Write Protect is off
[  430.973699] sd 2:0:0:0: [sdb] Mode Sense: 47 00 10 08
[  430.979136] sd 2:0:0:0: [sdb] No Caching mode page found
[  430.979155] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[  431.003317]  sdb: sdb1
[  431.015461] sd 2:0:0:0: [sdb] Attached SCSI disk
[  832.273302] ieee80211 phy0: rt2x00queue_flush_queue: Warning - Queue 2 failed to flush

Modération : merci à l'avenir d'utiliser les balises code (explications ici).

Dernière modification par cqfd93 (Le 07/10/2016, à 19:34)

Bougron

Re : accès après formatage à disque dur Western Digital Elements

Bonjour
Fais plutôt la commande  suivante

sudo fdisk -l