Contenu | Rechercher | Menus

Annonce

L'équipe des administrateurs et modérateurs du forum vous souhaite d'excellentes fêtes de fin d'année !

Si vous avez des soucis pour rester connecté, déconnectez-vous puis reconnectez-vous depuis ce lien en cochant la case
Me connecter automatiquement lors de mes prochaines visites.

À propos de l'équipe du forum.

#26 Le 22/12/2018, à 14:03

palikey

Re : DD Externe Iomega Ego Non Reconnu

sudo smartctl -s on -o on -a /dev/disk/by-id/wwn-0x50014ee205340884
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-4.4.0-140-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Western Digital Scorpio Blue Serial ATA (AF)
Device Model:     WDC WD10TPVT-65HT5T0
Serial Number:    WD-WXF1AA0N9988
LU WWN Device Id: 5 0014ee 205340884
Firmware Version: 01.01A01
User Capacity:    1 000 204 886 016 bytes [1,00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5200 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS (minor revision not indicated)
SATA Version is:  SATA 2.6, 3.0 Gb/s
Local Time is:    Sat Dec 22 13:40:24 2018 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
SMART Automatic Offline Testing Enabled every four hours.

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x80)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(25200) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 289) minutes.
Conveyance self-test routine
recommended polling time: 	 (   5) minutes.
SCT capabilities: 	       (0x7031)	SCT Status supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0027   201   188   021    Pre-fail  Always       -       2941
  4 Start_Stop_Count        0x0032   096   096   000    Old_age   Always       -       4815
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   200   200   000    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   093   093   000    Old_age   Always       -       5600
 10 Spin_Retry_Count        0x0032   100   100   000    Old_age   Always       -       0
 11 Calibration_Retry_Count 0x0032   100   100   000    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   096   096   000    Old_age   Always       -       4288
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       126
193 Load_Cycle_Count        0x0032   176   176   000    Old_age   Always       -       73402
194 Temperature_Celsius     0x0022   111   084   000    Old_age   Always       -       39
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   253   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0008   100   253   000    Old_age   Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
sudo smartctl -s on -o on -a /dev/disk/by-id/usb-ST350062_0AS_0-0:0
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-4.4.0-140-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

/dev/disk/by-id/usb-ST350062_0AS_0-0:0: Unknown USB bridge [0x067b:0x2506 (0x100)]
Please specify device type with the -d option.

Use smartctl -h to get a usage summary

Hors ligne

#27 Le 22/12/2018, à 15:17

moko138

Re : DD Externe Iomega Ego Non Reconnu

(Ton Western Digital 
/dev/disk/by-id/wwn-0x50014ee205340884
n'a que 5.600 heures et va très bien ! )  big_smile

  - -

Pour le Seagate derrière ton adaptateur ata-usb "0x067b:0x2506", alias "067b:2506"
essaie déjà ces deux variantes :

sudo smartctl -s on -o on -d usbjmicron -a /dev/disk/by-id/usb-ST350062_0AS_0-0:0

et

sudo smartctl -s on -o on -T verypermissive -d usbjmicron -a /dev/disk/by-id/usb-ST350062_0AS_0-0:0

%NOINDEX%
Un utilitaire méconnu : ncdu

Hors ligne

#28 Le 22/12/2018, à 15:38

palikey

Re : DD Externe Iomega Ego Non Reconnu

sudo smartctl -s on -o on -d usbjmicron -a /dev/disk/by-id/usb-ST350062_0AS_0-0:0
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-4.4.0-140-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

Smartctl open device: /dev/disk/by-id/usb-ST350062_0AS_0-0:0 [USB JMicron] failed: scsi error unsupported scsi opcode
sudo smartctl -s on -o on -T verypermissive -d usbjmicron -a /dev/disk/by-id/usb-ST350062_0AS_0-0:0
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-4.4.0-140-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

Smartctl open device: /dev/disk/by-id/usb-ST350062_0AS_0-0:0 [USB JMicron] failed: scsi error unsupported scsi opcode

Hors ligne

#29 Le 12/01/2019, à 14:04

palikey

Re : DD Externe Iomega Ego Non Reconnu

Pas d'avis par rapport à mon dernier message ?

Merci par avance

Hors ligne

#30 Le 12/01/2019, à 16:10

moko138

Re : DD Externe Iomega Ego Non Reconnu

Désolé, je n'avais pas vu ta réponse.

Suis retourné sur https://www.smartmontools.org/wiki/Supp … SB-Devices
ton adaptateur 0x067b:0x2506 (devant le Seagate 500 Go) est maintenant répertorié. Dans les périphériques pas encore pris en charge. sad


Ça n'empêche pas d'essayer.  En s'inspirant de

man smartctl

[NEW  EXPERIMENTAL  SMARTCTL  FEATURE]  The  Prolific  PL2507/3507  USB
bridges with older firmware support a pass-through command  similar  to
JMicron  and  work  with  ´-d  usbjmicron,0´.   Newer Prolific firmware
requires a modified command which can be selected by ´-d usbjmicron,p´.
Note that this does not yet support the SMART status command.

tenter :

sudo smartctl -s on -o on -d usbjmicron,0 -a /dev/disk/by-id/usb-ST350062_0AS_0-0:0

et

sudo smartctl -s on -o on -T verypermissive -d usbjmicron,0 -a /dev/disk/by-id/usb-ST350062_0AS_0-0:0

Et vu

man smartctl

usbprolific - [NEW EXPERIMENTAL SMARTCTL FEATURE] this  device  type  is  for  SATA
disks that are behind a Prolific PL2571/2771/2773/2775 USB to SATA bridge.

tenter :

sudo smartctl -s on -o on -d usbprolific -a /dev/disk/by-id/usb-ST350062_0AS_0-0:0

et

sudo smartctl -s on -o on -T verypermissive -d usbprolific -a /dev/disk/by-id/usb-ST350062_0AS_0-0:0

%NOINDEX%
Un utilitaire méconnu : ncdu

Hors ligne

#31 Le 14/01/2019, à 19:33

palikey

Re : DD Externe Iomega Ego Non Reconnu

Alors voici les résultats:

sudo smartctl -s on -o on -d usbjmicron,0 -a /dev/disk/by-id/usb-ST350062_0AS_0-0:0
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-4.4.0-141-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

Read Device Identity failed: scsi error unsupported scsi opcode

A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options.
sudo smartctl -s on -o on -T verypermissive -d usbjmicron,0 -a /dev/disk/by-id/usb-ST350062_0AS_0-0:0
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-4.4.0-141-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

Read Device Identity failed: scsi error unsupported scsi opcode

=== START OF INFORMATION SECTION ===
Device Model:     
Serial Number:    
Firmware Version: 
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   Unknown(0xfd00) (unknown minor revision code: 0x0065)
Local Time is:    Mon Jan 14 19:03:06 2019 CET
SMART support is: Ambiguous - ATA IDENTIFY DEVICE words 82-83 don't show if SMART supported.
SMART support is: Ambiguous - ATA IDENTIFY DEVICE words 85-87 don't show if SMART is enabled.
                  Checking to be sure by trying SMART RETURN STATUS command.
SMART support is: Unknown - Try option -s with argument 'on' to enable it.
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enable failed: scsi error unsupported scsi opcode

Read SMART Data failed: scsi error unsupported scsi opcode

SMART Automatic Timers not supported

SMART Enable Automatic Offline failed: scsi error unsupported scsi opcode


=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: UNKNOWN!
SMART Status, Attributes and Thresholds cannot be read.

Read SMART Error Log failed: scsi error unsupported scsi opcode

Read SMART Self-test Log failed: scsi error unsupported scsi opcode

Selective Self-tests/Logging not supported
sudo smartctl -s on -o on -d usbprolific -a /dev/disk/by-id/usb-ST350062_0AS_0-0:0
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-4.4.0-141-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

/dev/disk/by-id/usb-ST350062_0AS_0-0:0: Unknown USB device type 'usbprolific'
=======> VALID ARGUMENTS ARE: ata, scsi, sat[,auto][,N][+TYPE], usbcypress[,X], usbjmicron[,p][,x][,N], usbsunplus, marvell, areca,N/E, 3ware,N, hpt,L/M/N, megaraid,N, cciss,N, auto, test <=======

Use smartctl -h to get a usage summary
sudo smartctl -s on -o on -T verypermissive -d usbprolific -a /dev/disk/by-id/usb-ST350062_0AS_0-0:0
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-4.4.0-141-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

/dev/disk/by-id/usb-ST350062_0AS_0-0:0: Unknown USB device type 'usbprolific'
=======> VALID ARGUMENTS ARE: ata, scsi, sat[,auto][,N][+TYPE], usbcypress[,X], usbjmicron[,p][,x][,N], usbsunplus, marvell, areca,N/E, 3ware,N, hpt,L/M/N, megaraid,N, cciss,N, auto, test <=======

Use smartctl -h to get a usage summary

Hors ligne

#32 Hier à 07:30

moko138

Re : DD Externe Iomega Ego Non Reconnu

Récapitulatif :

Le Western Digital 1To, interne, en BON ÉTAT :
/dev/disk/by-id/ata-WDC_WD10TPVT-65HT5T0_WD-WXF1AA0N9988
/dev/disk/by-id/wwn-0x50014ee20534088


Le Seagate 500 Go, état INCONNU dans un boîtier LaCie à interface 067b:2506:
/dev/disk/by-id/usb-ST350062_0AS_0-0:0
En #18 : 465,8 Gio


Le boîtier Iomega contient le Samsung HM500JI
qui a le connecteur usb soudé : https://pix.toile-libre.org/?img=1544881573.jpg
Le Iomega "eGo USB", 500 Go en #1 et #3 :

Read Capacity(10) failed
[ 5351.721451] (...) idVendor=059b, idProduct=0070
[ 5352.887813] sd 6:0:0:0: [sdb] 975319088 512-byte logical blocks: (499 GB/465 GiB)
[ 5359.900295] blk_update_request: I/O error, dev sdb, sector 0
[ 5359.900302] Buffer I/O error on dev sdb, logical block 0, async page read

Et en #18 : 465,1 Gio
ls -l /dev/disk/by-id/  ?


Afin de cloner avec gddrescue le Iomega-Samsung,
on cherche un disque sain et ayant plus d'octets disponibles que le Iomega-Samsung.

Pour l'instant, on n'arrive pas à connaître l'état du Seagate, dont l'adaptateur Sata-usb n'est pas supporté par smartctl.


Contournements possibles :
  - brancher le Seagate à l'ordi via un autre adaptateur, supporté, lui ;
  - brancher le Seagate à l'ordi directement en Sata (s'il n'y a qu'un emplacement, cela implique de le substituer momentanément au WD 1To, et de démarrer en live) ;
  - brancher le Seagate en Sata à un autre ordi (une vieille tour est parfaite pour ça !) ;
  - Oublier le Seagate et utiliser un disque neuf.


Remarque :
On voit ici, une fois de plus, l'intérêt de choisir et d'acheter séparément
  - les disques (sans interface soudée ou exotique)
  - et les boîtiers (ou autres interfaces).


%NOINDEX%
Un utilitaire méconnu : ncdu

Hors ligne