#1 Le 13/05/2010, à 15:00
- Bebertii
[résolu]Détection du clavier et de la souris sous 10.04
Bonjour,
En dehors du fait que malgré un changement de noyau pour cause d'un problème sur les cartes wifi de mon portable et de mon fixe et que fglrx ne prend pas correctement en charge ma HD4830, et aussi que de temps à autre j'ai un gel complet de ma machine (Ctrl + F1 impossible), je persévère sous cette version LTS visiblement encore en version pré-alpha.
J'aimerais cette fois trouver le moyen d'avoir le contrôle de mon clavier et de ma souris immédiatement après l'apparition du bureau. En effet, actuellement, même si le clavier fonctionne lors de l'invite grub, celui-ci ainsi que ma souris mettent une bonne minute à devenir utilisables après la fin du chargement (le bluetooth aussi d'ailleurs, mais c'est moins gênant). Durant cette latence, les led de mon clavier ne s'allument pas et le laser de ma souris non plus, tout au plus un faible clignotement lorsque je presse un des boutons. Au bout d'une minute, j'entends un grattement du disque dur, les leds s'allument et je peux tout utiliser normalement.
Cela ressemble donc furieusement à un problème d'initialisation des ports USB, mais je ne sais pas comment le résoudre, et toute aide serait la bienvenue.
dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.33-02063303-generic (root@zinc) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #02063303 SMP Tue Apr 27 11:10:42 UTC 2010
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-2.6.33-02063303-generic root=UUID=eb20c4c6-2a37-499f-88cb-6c7e48a0b582 ro quiet splash
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000dff90000 (usable)
[ 0.000000] BIOS-e820: 00000000dff90000 - 00000000dff9e000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000dff9e000 - 00000000dffd0000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000dffd0000 - 00000000dffde000 (reserved)
[ 0.000000] BIOS-e820: 00000000dffe0000 - 00000000e0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000120000000 (usable)
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI present.
[ 0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working around it.
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] No AGP bridge found
[ 0.000000] last_pfn = 0x120000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-DFFFF write-protect
[ 0.000000] E0000-EFFFF write-through
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0E0000000 mask FE0000000 uncachable
[ 0.000000] 1 base 000000000 mask F00000000 write-back
[ 0.000000] 2 base 100000000 mask FE0000000 write-back
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820 update range: 00000000e0000000 - 0000000100000000 (usable) ==> (reserved)
[ 0.000000] last_pfn = 0xdff90 max_arch_pfn = 0x400000000
[ 0.000000] Scanning 0 areas for low memory corruption
[ 0.000000] modified physical RAM map:
[ 0.000000] modified: 0000000000000000 - 0000000000010000 (reserved)
[ 0.000000] modified: 0000000000010000 - 000000000009fc00 (usable)
[ 0.000000] modified: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] modified: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] modified: 0000000000100000 - 00000000dff90000 (usable)
[ 0.000000] modified: 00000000dff90000 - 00000000dff9e000 (ACPI data)
[ 0.000000] modified: 00000000dff9e000 - 00000000dffd0000 (ACPI NVS)
[ 0.000000] modified: 00000000dffd0000 - 00000000dffde000 (reserved)
[ 0.000000] modified: 00000000dffe0000 - 00000000e0000000 (reserved)
[ 0.000000] modified: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] modified: 00000000fff00000 - 0000000100000000 (reserved)
[ 0.000000] modified: 0000000100000000 - 0000000120000000 (usable)
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] found SMP MP-table at [ffff8800000ff780] ff780
[ 0.000000] init_memory_mapping: 0000000000000000-00000000dff90000
[ 0.000000] 0000000000 - 00dfe00000 page 2M
[ 0.000000] 00dfe00000 - 00dff90000 page 4k
[ 0.000000] kernel direct mapping tables up to dff90000 @ 16000-1c000
[ 0.000000] init_memory_mapping: 0000000100000000-0000000120000000
[ 0.000000] 0100000000 - 0120000000 page 2M
[ 0.000000] kernel direct mapping tables up to 120000000 @ 1a000-20000
[ 0.000000] RAMDISK: 377b8000 - 37fef437
[ 0.000000] ACPI: RSDP 00000000000fb630 00014 (v00 ACPIAM)
[ 0.000000] ACPI: RSDT 00000000dff90000 0003C (v01 A_M_I_ OEMRSDT 07000908 MSFT 00000097)
[ 0.000000] ACPI: FACP 00000000dff90200 00084 (v02 A_M_I_ OEMFACP 07000908 MSFT 00000097)
[ 0.000000] ACPI: DSDT 00000000dff905c0 07C37 (v01 A0846 A0846000 00000000 INTL 20060113)
[ 0.000000] ACPI: FACS 00000000dff9e000 00040
[ 0.000000] ACPI: APIC 00000000dff90390 0006C (v01 A_M_I_ OEMAPIC 07000908 MSFT 00000097)
[ 0.000000] ACPI: MCFG 00000000dff90400 0003C (v01 A_M_I_ OEMMCFG 07000908 MSFT 00000097)
[ 0.000000] ACPI: OEMB 00000000dff9e040 00080 (v01 A_M_I_ AMI_OEM 07000908 MSFT 00000097)
[ 0.000000] ACPI: HPET 00000000dff98200 00038 (v01 A_M_I_ OEMHPET 07000908 MSFT 00000097)
[ 0.000000] ACPI: GSCI 00000000dff9e0c0 02024 (v01 A_M_I_ GMCHSCI 07000908 MSFT 00000097)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-0000000120000000
[ 0.000000] Bootmem setup node 0 0000000000000000-0000000120000000
[ 0.000000] NODE_DATA [000000000001b000 - 000000000001ffff]
[ 0.000000] bootmap [0000000000020000 - 0000000000043fff] pages 24
[ 0.000000] (13 early reservations) ==> bootmem [0000000000 - 0120000000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0001000000 - 0001cb8354] TEXT DATA BSS ==> [0001000000 - 0001cb8354]
[ 0.000000] #2 [00377b8000 - 0037fef437] RAMDISK ==> [00377b8000 - 0037fef437]
[ 0.000000] #3 [0001cb9000 - 0001cb9284] BRK ==> [0001cb9000 - 0001cb9284]
[ 0.000000] #4 [00000ff790 - 0000100000] BIOS reserved ==> [00000ff790 - 0000100000]
[ 0.000000] #5 [00000ff780 - 00000ff790] MP-table mpf ==> [00000ff780 - 00000ff790]
[ 0.000000] #6 [000009fc00 - 00000f1900] BIOS reserved ==> [000009fc00 - 00000f1900]
[ 0.000000] #7 [00000f1a6c - 00000ff780] BIOS reserved ==> [00000f1a6c - 00000ff780]
[ 0.000000] #8 [00000f1900 - 00000f1a6c] MP-table mpc ==> [00000f1900 - 00000f1a6c]
[ 0.000000] #9 [0000010000 - 0000012000] TRAMPOLINE ==> [0000010000 - 0000012000]
[ 0.000000] #10 [0000012000 - 0000016000] ACPI WAKEUP ==> [0000012000 - 0000016000]
[ 0.000000] #11 [0000016000 - 000001a000] PGTABLE ==> [0000016000 - 000001a000]
[ 0.000000] #12 [000001a000 - 000001b000] PGTABLE ==> [000001a000 - 000001b000]
[ 0.000000] [ffffea0000000000-ffffea0003ffffff] PMD -> [ffff880028600000-ffff88002bffffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x00120000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[3] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x000dff90
[ 0.000000] 0: 0x00100000 -> 0x00120000
[ 0.000000] On node 0 totalpages: 1048351
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 106 pages reserved
[ 0.000000] DMA zone: 3821 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14280 pages used for memmap
[ 0.000000] DMA32 zone: 899016 pages, LIFO batch:31
[ 0.000000] Normal zone: 1792 pages used for memmap
[ 0.000000] Normal zone: 129280 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000
[ 0.000000] PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 00000000dff90000 - 00000000dff9e000
[ 0.000000] PM: Registered nosave memory: 00000000dff9e000 - 00000000dffd0000
[ 0.000000] PM: Registered nosave memory: 00000000dffd0000 - 00000000dffde000
[ 0.000000] PM: Registered nosave memory: 00000000dffde000 - 00000000dffe0000
[ 0.000000] PM: Registered nosave memory: 00000000dffe0000 - 00000000e0000000
[ 0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000fee00000
[ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
[ 0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000fff00000
[ 0.000000] PM: Registered nosave memory: 00000000fff00000 - 0000000100000000
[ 0.000000] Allocating PCI resources starting at e0000000 (gap: e0000000:1ee00000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 30 pages/cpu @ffff880028200000 s91672 r8192 d23016 u524288
[ 0.000000] pcpu-alloc: s91672 r8192 d23016 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1032117
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.33-02063303-generic root=UUID=eb20c4c6-2a37-499f-88cb-6c7e48a0b582 ro quiet splash
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] xsave/xrstor: enabled xstate_bv 0x3, cntxt size 0x240
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 4045884k/4718592k available (5391k kernel code, 525188k absent, 147520k reserved, 5547k data, 952k init)
[ 0.000000] SLUB: Genslabs=14, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:4352 nr_irqs:440
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 41943040 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 3360.074 MHz processor.
[ 0.000006] Calibrating delay loop (skipped), value calculated using timer frequency.. 6720.14 BogoMIPS (lpj=33600740)
[ 0.000026] Security Framework initialized
[ 0.000032] SELinux: Disabled at boot.
[ 0.000279] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.011218] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.011930] Mount-cache hash table entries: 256
[ 0.012039] Initializing cgroup subsys ns
[ 0.012044] Initializing cgroup subsys cpuacct
[ 0.012046] Initializing cgroup subsys memory
[ 0.012051] Initializing cgroup subsys devices
[ 0.012053] Initializing cgroup subsys freezer
[ 0.012054] Initializing cgroup subsys net_cls
[ 0.012071] CPU: Physical Processor ID: 0
[ 0.012072] CPU: Processor Core ID: 0
[ 0.012075] mce: CPU supports 6 MCE banks
[ 0.012081] CPU0: Thermal monitoring enabled (TM2)
[ 0.012084] using mwait in idle threads.
[ 0.012086] Performance Events: Core2 events, Intel PMU driver.
[ 0.012090] ... version: 2
[ 0.012091] ... bit width: 40
[ 0.012091] ... generic registers: 2
[ 0.012093] ... value mask: 000000ffffffffff
[ 0.012094] ... max period: 000000007fffffff
[ 0.012095] ... fixed-purpose events: 3
[ 0.012096] ... event mask: 0000000700000003
[ 0.013934] ACPI: Core revision 20091214
[ 0.030005] ftrace: converting mcount calls to 0f 1f 44 00 00
[ 0.030009] ftrace: allocating 26557 entries in 105 pages
[ 0.040035] Setting APIC routing to flat
[ 0.040330] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.141500] CPU0: Intel(R) Core(TM)2 Duo CPU E7400 @ 2.80GHz stepping 0a
[ 0.150000] APIC calibration not consistent with PM-Timer: 129ms instead of 100ms
[ 0.150000] APIC delta adjusted to PM-Timer: 1999996 (2599977)
[ 0.150000] Booting Node 0, Processors #1
[ 0.310015] Brought up 2 CPUs
[ 0.310018] Total of 2 processors activated (13440.14 BogoMIPS).
[ 0.310544] devtmpfs: initialized
[ 0.310544] regulator: core version 0.5
[ 0.310544] Time: 14:37:15 Date: 05/13/10
[ 0.310544] NET: Registered protocol family 16
[ 0.310544] ACPI: bus type pci registered
[ 0.310544] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf0000000-0xf3ffffff] (base 0xf0000000)
[ 0.310544] PCI: not using MMCONFIG
[ 0.310544] PCI: Using configuration type 1 for base access
[ 0.310554] bio: create slab <bio-0> at 0
[ 0.310766] ACPI: EC: Look up EC in DSDT
[ 0.313009] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.316958] ACPI: Interpreter enabled
[ 0.316962] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.316976] ACPI: Using IOAPIC for interrupt routing
[ 0.317010] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf0000000-0xf3ffffff] (base 0xf0000000)
[ 0.320701] PCI: MMCONFIG at [mem 0xf0000000-0xf3ffffff] reserved in ACPI motherboard resources
[ 0.326993] ACPI Warning: Incorrect checksum in table [OEMB] - 77, should be 72 (20091214/tbutils-314)
[ 0.327613] ACPI: No dock devices found.
[ 0.327688] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.327707] pci_root PNP0A08:00: ignoring host bridge windows from ACPI; boot with "pci=use_crs" to use them
[ 0.327841] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7] (ignored)
[ 0.327843] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff] (ignored)
[ 0.327844] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
[ 0.327846] pci_root PNP0A08:00: host bridge window [mem 0x000d0000-0x000dffff] (ignored)
[ 0.327847] pci_root PNP0A08:00: host bridge window [mem 0xe0000000-0xffffffff] (ignored)
[ 0.327896] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.327898] pci 0000:00:01.0: PME# disabled
[ 0.327937] pci 0000:00:1b.0: reg 10: [mem 0xfe8fc000-0xfe8fffff 64bit]
[ 0.327967] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.327970] pci 0000:00:1b.0: PME# disabled
[ 0.328017] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.328019] pci 0000:00:1c.0: PME# disabled
[ 0.328067] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.328070] pci 0000:00:1c.1: PME# disabled
[ 0.328105] pci 0000:00:1d.0: reg 20: [io 0xc480-0xc49f]
[ 0.328140] pci 0000:00:1d.1: reg 20: [io 0xc800-0xc81f]
[ 0.328175] pci 0000:00:1d.2: reg 20: [io 0xc880-0xc89f]
[ 0.328209] pci 0000:00:1d.3: reg 20: [io 0xcc00-0xcc1f]
[ 0.328245] pci 0000:00:1d.7: reg 10: [mem 0xfe8fbc00-0xfe8fbfff]
[ 0.328284] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.328287] pci 0000:00:1d.7: PME# disabled
[ 0.328373] pci 0000:00:1f.0: quirk: [io 0x0800-0x087f] claimed by ICH6 ACPI/GPIO/TCO
[ 0.328376] pci 0000:00:1f.0: quirk: [io 0x0480-0x04bf] claimed by ICH6 GPIO
[ 0.328378] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0294 (mask 0003)
[ 0.328410] pci 0000:00:1f.1: reg 10: [io 0x0000-0x0007]
[ 0.328415] pci 0000:00:1f.1: reg 14: [io 0x0000-0x0003]
[ 0.328419] pci 0000:00:1f.1: reg 18: [io 0x08f0-0x08f7]
[ 0.328424] pci 0000:00:1f.1: reg 1c: [io 0x08f8-0x08fb]
[ 0.328428] pci 0000:00:1f.1: reg 20: [io 0xffa0-0xffaf]
[ 0.328455] pci 0000:00:1f.2: reg 10: [io 0xc400-0xc407]
[ 0.328459] pci 0000:00:1f.2: reg 14: [io 0xc080-0xc083]
[ 0.328463] pci 0000:00:1f.2: reg 18: [io 0xc000-0xc007]
[ 0.328466] pci 0000:00:1f.2: reg 1c: [io 0xbc00-0xbc03]
[ 0.328470] pci 0000:00:1f.2: reg 20: [io 0xb880-0xb88f]
[ 0.328487] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.328489] pci 0000:00:1f.2: PME# disabled
[ 0.328523] pci 0000:00:1f.3: reg 20: [io 0x0400-0x041f]
[ 0.328559] pci 0000:01:00.0: reg 10: [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.328566] pci 0000:01:00.0: reg 18: [mem 0xfe9e0000-0xfe9effff 64bit]
[ 0.328570] pci 0000:01:00.0: reg 20: [io 0xd000-0xd0ff]
[ 0.328576] pci 0000:01:00.0: reg 30: [mem 0xfe9c0000-0xfe9dffff pref]
[ 0.328589] pci 0000:01:00.0: supports D1 D2
[ 0.328610] pci 0000:01:00.1: reg 10: [mem 0xfe9fc000-0xfe9fffff 64bit]
[ 0.328636] pci 0000:01:00.1: supports D1 D2
[ 0.328668] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.328669] pci 0000:00:01.0: bridge window [io 0xd000-0xdfff]
[ 0.328671] pci 0000:00:01.0: bridge window [mem 0xfe900000-0xfe9fffff]
[ 0.328674] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.328700] pci 0000:00:1c.0: PCI bridge to [bus 03-03]
[ 0.328735] pci 0000:02:00.0: reg 10: [io 0xe800-0xe8ff]
[ 0.328751] pci 0000:02:00.0: reg 18: [mem 0xfdfff000-0xfdffffff 64bit pref]
[ 0.328763] pci 0000:02:00.0: reg 20: [mem 0xfdfe0000-0xfdfeffff 64bit pref]
[ 0.328769] pci 0000:02:00.0: reg 30: [mem 0xfeaf0000-0xfeafffff pref]
[ 0.328801] pci 0000:02:00.0: supports D1 D2
[ 0.328803] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.328806] pci 0000:02:00.0: PME# disabled
[ 0.328848] pci 0000:00:1c.1: PCI bridge to [bus 02-02]
[ 0.328851] pci 0000:00:1c.1: bridge window [io 0xe000-0xefff]
[ 0.328854] pci 0000:00:1c.1: bridge window [mem 0xfea00000-0xfeafffff]
[ 0.328858] pci 0000:00:1c.1: bridge window [mem 0xfdf00000-0xfdffffff 64bit pref]
[ 0.328882] pci 0000:04:01.0: reg 10: [mem 0xfebfe000-0xfebfffff]
[ 0.328953] pci 0000:00:1e.0: PCI bridge to [bus 04-04] (subtractive decode)
[ 0.328957] pci 0000:00:1e.0: bridge window [mem 0xfeb00000-0xfebfffff]
[ 0.328974] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.329051] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 0.329107] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[ 0.329143] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
[ 0.334928] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 0.335002] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 0.335074] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15)
[ 0.335147] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 0.335219] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.335292] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.335365] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.335438] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.335508] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.335510] vgaarb: loaded
[ 0.335566] SCSI subsystem initialized
[ 0.335598] libata version 3.00 loaded.
[ 0.335598] usbcore: registered new interface driver usbfs
[ 0.335598] usbcore: registered new interface driver hub
[ 0.335598] usbcore: registered new device driver usb
[ 0.335598] ACPI: WMI: Mapper loaded
[ 0.335598] PCI: Using ACPI for IRQ routing
[ 0.335598] PCI: pci_cache_line_size set to 64 bytes
[ 0.335598] NetLabel: Initializing
[ 0.335598] NetLabel: domain hash size = 128
[ 0.335598] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.335598] NetLabel: unlabeled traffic allowed by default
[ 0.335598] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.335598] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.335598] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.340011] Switching to clocksource tsc
[ 0.341173] pnp: PnP ACPI init
[ 0.341178] ACPI: bus type pnp registered
[ 0.343718] pnp: PnP ACPI: found 18 devices
[ 0.343720] ACPI: ACPI bus type pnp unregistered
[ 0.343726] system 00:01: [mem 0xfed14000-0xfed19fff] has been reserved
[ 0.343730] system 00:07: [io 0x0290-0x0297] has been reserved
[ 0.343734] system 00:08: [io 0x04d0-0x04d1] has been reserved
[ 0.343736] system 00:08: [io 0x0800-0x087f] has been reserved
[ 0.343737] system 00:08: [io 0x0480-0x04bf] has been reserved
[ 0.343739] system 00:08: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.343741] system 00:08: [mem 0xfed20000-0xfed8ffff] has been reserved
[ 0.343744] system 00:0b: [mem 0xffc00000-0xffefffff] has been reserved
[ 0.343748] system 00:0c: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.343749] system 00:0c: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.343755] system 00:10: [mem 0xf0000000-0xf3ffffff] has been reserved
[ 0.343758] system 00:11: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.343760] system 00:11: [mem 0x000c0000-0x000cffff] has been reserved
[ 0.343762] system 00:11: [mem 0x000e0000-0x000fffff] could not be reserved
[ 0.343763] system 00:11: [mem 0x00100000-0xdfffffff] could not be reserved
[ 0.348391] pci 0000:00:1c.0: BAR 14: assigned [mem 0xf4000000-0xf41fffff]
[ 0.348393] pci 0000:00:1c.0: BAR 15: assigned [mem 0xf4200000-0xf43fffff 64bit pref]
[ 0.348395] pci 0000:00:1c.0: BAR 13: assigned [io 0x1000-0x1fff]
[ 0.348396] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.348398] pci 0000:00:01.0: bridge window [io 0xd000-0xdfff]
[ 0.348400] pci 0000:00:01.0: bridge window [mem 0xfe900000-0xfe9fffff]
[ 0.348403] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.348405] pci 0000:00:1c.0: PCI bridge to [bus 03-03]
[ 0.348407] pci 0000:00:1c.0: bridge window [io 0x1000-0x1fff]
[ 0.348410] pci 0000:00:1c.0: bridge window [mem 0xf4000000-0xf41fffff]
[ 0.348413] pci 0000:00:1c.0: bridge window [mem 0xf4200000-0xf43fffff 64bit pref]
[ 0.348417] pci 0000:00:1c.1: PCI bridge to [bus 02-02]
[ 0.348419] pci 0000:00:1c.1: bridge window [io 0xe000-0xefff]
[ 0.348422] pci 0000:00:1c.1: bridge window [mem 0xfea00000-0xfeafffff]
[ 0.348425] pci 0000:00:1c.1: bridge window [mem 0xfdf00000-0xfdffffff 64bit pref]
[ 0.348429] pci 0000:00:1e.0: PCI bridge to [bus 04-04]
[ 0.348430] pci 0000:00:1e.0: bridge window [io disabled]
[ 0.348434] pci 0000:00:1e.0: bridge window [mem 0xfeb00000-0xfebfffff]
[ 0.348436] pci 0000:00:1e.0: bridge window [mem pref disabled]
[ 0.348443] alloc irq_desc for 16 on node -1
[ 0.348445] alloc kstat_irqs on node -1
[ 0.348448] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.348450] pci 0000:00:01.0: setting latency timer to 64
[ 0.348455] pci 0000:00:1c.0: enabling device (0104 -> 0107)
[ 0.348457] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.348460] pci 0000:00:1c.0: setting latency timer to 64
[ 0.348466] alloc irq_desc for 17 on node -1
[ 0.348467] alloc kstat_irqs on node -1
[ 0.348469] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.348472] pci 0000:00:1c.1: setting latency timer to 64
[ 0.348476] pci 0000:00:1e.0: setting latency timer to 64
[ 0.348478] pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
[ 0.348480] pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffffffffffff]
[ 0.348481] pci_bus 0000:01: resource 0 [io 0xd000-0xdfff]
[ 0.348482] pci_bus 0000:01: resource 1 [mem 0xfe900000-0xfe9fffff]
[ 0.348484] pci_bus 0000:01: resource 2 [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.348485] pci_bus 0000:03: resource 0 [io 0x1000-0x1fff]
[ 0.348487] pci_bus 0000:03: resource 1 [mem 0xf4000000-0xf41fffff]
[ 0.348488] pci_bus 0000:03: resource 2 [mem 0xf4200000-0xf43fffff 64bit pref]
[ 0.348490] pci_bus 0000:02: resource 0 [io 0xe000-0xefff]
[ 0.348491] pci_bus 0000:02: resource 1 [mem 0xfea00000-0xfeafffff]
[ 0.348492] pci_bus 0000:02: resource 2 [mem 0xfdf00000-0xfdffffff 64bit pref]
[ 0.348494] pci_bus 0000:04: resource 1 [mem 0xfeb00000-0xfebfffff]
[ 0.348495] pci_bus 0000:04: resource 3 [io 0x0000-0xffff]
[ 0.348497] pci_bus 0000:04: resource 4 [mem 0x00000000-0xffffffffffffffff]
[ 0.348511] NET: Registered protocol family 2
[ 0.348601] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.349300] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[ 0.352021] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.352377] TCP: Hash tables configured (established 524288 bind 65536)
[ 0.352379] TCP reno registered
[ 0.352384] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.352413] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.352517] NET: Registered protocol family 1
[ 0.352615] pci 0000:01:00.0: Boot video device
[ 0.352623] PCI: CLS 32 bytes, default 64
[ 0.352671] Trying to unpack rootfs image as initramfs...
[ 0.477818] Freeing initrd memory: 8413k freed
[ 0.480194] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.480197] Placing 64MB software IO TLB between ffff880020000000 - ffff880024000000
[ 0.480199] software IO TLB at phys 0x20000000 - 0x24000000
[ 0.480365] Scanning for low memory corruption every 60 seconds
[ 0.480472] audit: initializing netlink socket (disabled)
[ 0.480483] type=2000 audit(1273761434.479:1): initialized
[ 0.490313] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.491162] VFS: Disk quotas dquot_6.5.2
[ 0.491193] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.491522] fuse init (API version 7.13)
[ 0.491568] msgmni has been set to 7918
[ 0.491690] alg: No test for stdrng (krng)
[ 0.491722] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.491724] io scheduler noop registered
[ 0.491725] io scheduler deadline registered
[ 0.491759] io scheduler cfq registered (default)
[ 0.491818] pcieport 0000:00:01.0: setting latency timer to 64
[ 0.491833] alloc irq_desc for 24 on node -1
[ 0.491835] alloc kstat_irqs on node -1
[ 0.491841] pcieport 0000:00:01.0: irq 24 for MSI/MSI-X
[ 0.491873] pcieport 0000:00:1c.0: setting latency timer to 64
[ 0.491895] alloc irq_desc for 25 on node -1
[ 0.491896] alloc kstat_irqs on node -1
[ 0.491901] pcieport 0000:00:1c.0: irq 25 for MSI/MSI-X
[ 0.491951] pcieport 0000:00:1c.1: setting latency timer to 64
[ 0.491972] alloc irq_desc for 26 on node -1
[ 0.491973] alloc kstat_irqs on node -1
[ 0.491978] pcieport 0000:00:1c.1: irq 26 for MSI/MSI-X
[ 0.492035] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.492086] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.492171] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.492173] ACPI: Power Button [PWRB]
[ 0.492201] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.492203] ACPI: Power Button [PWRF]
[ 0.492588] ACPI: SSDT 00000000dffa00f0 00214 (v01 AMI CPU1PM 00000001 INTL 20060113)
[ 0.493029] ACPI: SSDT 00000000dffa0310 00143 (v01 AMI CPU2PM 00000001 INTL 20060113)
[ 0.495751] Linux agpgart interface v0.103
[ 0.495763] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.495842] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.496123] 00:0f: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.496725] brd: module loaded
[ 0.496998] loop: module loaded
[ 0.497049] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[ 0.497094] ata_piix 0000:00:1f.1: version 2.13
[ 0.497101] alloc irq_desc for 18 on node -1
[ 0.497102] alloc kstat_irqs on node -1
[ 0.497106] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 0.497129] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 0.497191] scsi0 : ata_piix
[ 0.497227] scsi1 : ata_piix
[ 0.498157] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[ 0.498159] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[ 0.498173] alloc irq_desc for 23 on node -1
[ 0.498174] alloc kstat_irqs on node -1
[ 0.498178] ata_piix 0000:00:1f.2: PCI INT B -> GSI 23 (level, low) -> IRQ 23
[ 0.498180] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[ 0.498206] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 0.498251] scsi2 : ata_piix
[ 0.498279] scsi3 : ata_piix
[ 0.499211] ata3: SATA max UDMA/133 cmd 0xc400 ctl 0xc080 bmdma 0xb880 irq 23
[ 0.499213] ata4: SATA max UDMA/133 cmd 0xc000 ctl 0xbc00 bmdma 0xb888 irq 23
[ 0.499389] Fixed MDIO Bus: probed
[ 0.499406] PPP generic driver version 2.4.2
[ 0.499426] tun: Universal TUN/TAP device driver, 1.6
[ 0.499427] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.499474] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.499487] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.499498] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 0.499500] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 0.499518] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 0.499532] ehci_hcd 0000:00:1d.7: using broken periodic workaround
[ 0.499539] ehci_hcd 0000:00:1d.7: debug port 1
[ 0.503425] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 0.503428] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfe8fbc00
[ 0.519840] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 0.519940] hub 1-0:1.0: USB hub found
[ 0.519945] hub 1-0:1.0: 8 ports detected
[ 0.519994] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.520001] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.520027] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.520031] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 0.520033] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 0.520055] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 0.520073] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000c480
[ 0.520138] hub 2-0:1.0: USB hub found
[ 0.520140] hub 2-0:1.0: 2 ports detected
[ 0.520167] alloc irq_desc for 19 on node -1
[ 0.520168] alloc kstat_irqs on node -1
[ 0.520171] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.520174] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 0.520176] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 0.520195] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 0.520218] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000c800
[ 0.520280] hub 3-0:1.0: USB hub found
[ 0.520282] hub 3-0:1.0: 2 ports detected
[ 0.520308] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.520312] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 0.520314] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 0.520331] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 0.520353] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000c880
[ 0.520417] hub 4-0:1.0: USB hub found
[ 0.520419] hub 4-0:1.0: 2 ports detected
[ 0.520444] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[ 0.520448] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 0.520450] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 0.520467] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 0.520493] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000cc00
[ 0.520555] hub 5-0:1.0: USB hub found
[ 0.520557] hub 5-0:1.0: 2 ports detected
[ 0.520613] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 0.523086] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.523090] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.523147] mice: PS/2 mouse device common for all mice
[ 0.523209] rtc_cmos 00:03: RTC can wake from S4
[ 0.523231] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 0.523250] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 0.523303] device-mapper: uevent: version 1.0.3
[ 0.523360] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel@redhat.com
[ 0.523395] device-mapper: multipath: version 1.1.1 loaded
[ 0.523397] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 0.523480] cpuidle: using governor ladder
[ 0.523482] cpuidle: using governor menu
[ 0.523645] TCP cubic registered
[ 0.523716] NET: Registered protocol family 10
[ 0.523950] lo: Disabled Privacy Extensions
[ 0.524082] NET: Registered protocol family 17
[ 0.524407] PM: Resume from disk failed.
[ 0.524417] registered taskstats version 1
[ 0.524576] Magic number: 10:36:637
[ 0.524623] rtc_cmos 00:03: setting system clock to 2010-05-13 14:37:15 UTC (1273761435)
[ 0.524625] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 0.524626] EDD information not available.
[ 0.680093] ata4.01: ATA-7: FUJITSU MHV2040BH, 892C, max UDMA/100
[ 0.680094] ata4.01: 78165360 sectors, multi 16: LBA48
[ 0.680201] ata3.00: ATA-8: Hitachi HDP725032GLA360, GM3OA5CA, max UDMA/133
[ 0.680203] ata3.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 0.719967] ata4.01: configured for UDMA/100
[ 0.720231] ata3.00: configured for UDMA/133
[ 0.832923] ata1.00: ATA-7: ST3500630A, 3.AAF, max UDMA/100
[ 0.832926] ata1.00: 976773168 sectors, multi 16: LBA48
[ 0.832950] ata1.01: ATAPI: JLMS XJ-HD166S, DS1A, max UDMA/33
[ 0.839956] usb 1-2: new high speed USB device using ehci_hcd and address 2
[ 0.924468] ata1.00: configured for UDMA/100
[ 0.924857] ata1.01: configured for UDMA/33
[ 0.925496] scsi 0:0:0:0: Direct-Access ATA ST3500630A 3.AA PQ: 0 ANSI: 5
[ 0.925609] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 0.925618] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 0.925855] sd 0:0:0:0: [sda] Write Protect is off
[ 0.925858] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 0.925862] scsi 0:0:1:0: CD-ROM JLMS XJ-HD166S DS1A PQ: 0 ANSI: 5
[ 0.925889] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 0.927402] sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray
[ 0.927405] Uniform CD-ROM driver Revision: 3.20
[ 0.927451] sda:
[ 0.927492] sr 0:0:1:0: Attached scsi CD-ROM sr0
[ 0.927531] sr 0:0:1:0: Attached scsi generic sg1 type 5
[ 0.927592] scsi 2:0:0:0: Direct-Access ATA Hitachi HDP72503 GM3O PQ: 0 ANSI: 5
[ 0.927652] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 0.927686] sd 2:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[ 0.927707] scsi 3:0:1:0: Direct-Access ATA FUJITSU MHV2040B 892C PQ: 0 ANSI: 5
[ 0.927722] sd 2:0:0:0: [sdb] Write Protect is off
[ 0.927723] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 0.927738] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 0.927772] sd 3:0:1:0: Attached scsi generic sg3 type 0
[ 0.927787] sd 3:0:1:0: [sdc] 78165360 512-byte logical blocks: (40.0 GB/37.2 GiB)
[ 0.927821] sd 3:0:1:0: [sdc] Write Protect is off
[ 0.927822] sd 3:0:1:0: [sdc] Mode Sense: 00 3a 00 00
[ 0.927837] sd 3:0:1:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 0.927915] sdc:
[ 0.928022] sdb: sdb1 sdb2 < sdb5 sda1 sda2 sda3
[ 0.985143] sdb6 >
[ 0.985359] sd 2:0:0:0: [sdb] Attached SCSI disk
[ 0.991126] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.294299] sdc2 < sdc5 sdc6 >
[ 1.352601] sd 3:0:1:0: [sdc] Attached SCSI disk
[ 1.352613] Freeing unused kernel memory: 952k freed
[ 1.352818] Write protecting the kernel read-only data: 10240k
[ 1.352919] Freeing unused kernel memory: 732k freed
[ 1.353160] Freeing unused kernel memory: 1708k freed
[ 1.361975] udev: starting version 151
[ 1.404070] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 1.404090] r8169 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 1.404132] r8169 0000:02:00.0: setting latency timer to 64
[ 1.404168] alloc irq_desc for 27 on node -1
[ 1.404170] alloc kstat_irqs on node -1
[ 1.404181] r8169 0000:02:00.0: irq 27 for MSI/MSI-X
[ 1.404505] eth0: RTL8102e at 0xffffc9000067a000, 00:23:54:5d:17:0d, XID 04a00000 IRQ 27
[ 1.411289] usb 1-7: new high speed USB device using ehci_hcd and address 7
[ 1.737696] EXT4-fs (sda2): mounted filesystem with ordered data mode
[ 11.875594] udev: starting version 151
[ 11.887870] Adding 1558296k swap on /dev/sda3. Priority:-1 extents:1 across:1558296k
[ 12.246705] intel_rng: FWH not detected
[ 12.504641] [drm] Initialized drm 1.1.0 20060810
[ 12.549785] cfg80211: Calling CRDA to update world regulatory domain
[ 12.555916] lp: driver loaded but no devices found
[ 12.672884] parport_pc 00:06: reported by Plug and Play ACPI
[ 12.672984] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[ 12.721477] cfg80211: World regulatory domain updated:
[ 12.721479] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 12.721481] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.721483] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 12.721484] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 12.721486] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.721487] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.752829] lp0: using parport0 (interrupt-driven).
[ 12.762306] ppdev: user-space parallel port driver
[ 12.959237] [drm] radeon defaulting to kernel modesetting.
[ 12.959239] [drm] radeon kernel modesetting enabled.
[ 12.959274] radeon 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 12.959277] radeon 0000:01:00.0: setting latency timer to 64
[ 12.961086] [drm] radeon: Initializing kernel modesetting.
[ 12.961196] [drm] register mmio base: 0xFE9E0000
[ 12.961197] [drm] register mmio size: 65536
[ 12.961265] ATOM BIOS: Wekiva
[ 12.961278] [drm] Clocks initialized !
[ 12.961292] mtrr: type mismatch for e0000000,10000000 old: write-back new: write-combining
[ 12.961293] [drm] Detected VRAM RAM=256M, BAR=256M
[ 12.961295] [drm] RAM width 256bits DDR
[ 12.961319] [TTM] Zone kernel: Available graphics memory: 2028846 kiB.
[ 12.961330] [drm] radeon: 256M of VRAM memory ready
[ 12.961331] [drm] radeon: 512M of GTT memory ready.
[ 12.961357] alloc irq_desc for 28 on node -1
[ 12.961359] alloc kstat_irqs on node -1
[ 12.961366] radeon 0000:01:00.0: irq 28 for MSI/MSI-X
[ 12.961370] [drm] radeon: using MSI.
[ 12.961392] [drm] radeon: irq initialized.
[ 12.961394] [drm] GART: num cpu pages 131072, num gpu pages 131072
[ 12.961852] [drm] Loading RV770 Microcode
[ 12.961907] platform radeon_cp.0: firmware: requesting radeon/RV770_pfp.bin
[ 13.108197] rt2500pci 0000:04:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 13.359010] phy0: Selected rate control algorithm 'minstrel'
[ 13.359372] Registered led device: rt2500pci-phy0::radio
[ 13.359383] Registered led device: rt2500pci-phy0::quality
[ 13.364530] platform radeon_cp.0: firmware: requesting radeon/RV770_me.bin
[ 13.428147] platform radeon_cp.0: firmware: requesting radeon/R700_rlc.bin
[ 13.476421] [drm] ring test succeeded in 1 usecs
[ 13.476496] [drm] radeon: ib pool ready.
[ 13.476550] [drm] ib test succeeded in 0 usecs
[ 13.476745] [drm] Default TV standard: PAL
[ 13.476938] [drm] Radeon Display Connectors
[ 13.476939] [drm] Connector 0:
[ 13.476940] [drm] DVI-I
[ 13.476941] [drm] HPD1
[ 13.476942] [drm] DDC: 0x7e60 0x7e60 0x7e64 0x7e64 0x7e68 0x7e68 0x7e6c 0x7e6c
[ 13.476943] [drm] Encoders:
[ 13.476944] [drm] DFP1: INTERNAL_UNIPHY
[ 13.476945] [drm] CRT2: INTERNAL_KLDSCP_DAC2
[ 13.476946] [drm] Connector 1:
[ 13.476947] [drm] DIN
[ 13.476948] [drm] Encoders:
[ 13.476949] [drm] TV1: INTERNAL_KLDSCP_DAC2
[ 13.476949] [drm] Connector 2:
[ 13.476950] [drm] DVI-I
[ 13.476951] [drm] HPD2
[ 13.476952] [drm] DDC: 0x7e20 0x7e20 0x7e24 0x7e24 0x7e28 0x7e28 0x7e2c 0x7e2c
[ 13.476953] [drm] Encoders:
[ 13.476954] [drm] CRT1: INTERNAL_KLDSCP_DAC1
[ 13.476955] [drm] DFP2: INTERNAL_KLDSCP_LVTMA
[ 13.612700] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 13.612737] alloc irq_desc for 29 on node -1
[ 13.612738] alloc kstat_irqs on node -1
[ 13.612746] HDA Intel 0000:00:1b.0: irq 29 for MSI/MSI-X
[ 13.612765] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 13.653838] composite sync not supported
[ 13.716597] [drm] fb mappable at 0xE0141000
[ 13.716599] [drm] vram apper at 0xE0000000
[ 13.716600] [drm] size 6553600
[ 13.716601] [drm] fb depth is 24
[ 13.716602] [drm] pitch is 6400
[ 13.716709] fb0: radeondrmfb frame buffer device
[ 13.716710] registered panic notifier
[ 13.716714] [drm] Initialized radeon 2.0.0 20080528 for 0000:01:00.0 on minor 0
[ 13.789430] HDA Intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 13.789471] alloc irq_desc for 30 on node -1
[ 13.789473] alloc kstat_irqs on node -1
[ 13.789479] HDA Intel 0000:01:00.1: irq 30 for MSI/MSI-X
[ 13.789497] HDA Intel 0000:01:00.1: setting latency timer to 64
[ 13.827085] composite sync not supported
[ 13.863958] Console: switching to colour frame buffer device 160x56
[ 16.531265] usb 1-7: device descriptor read/64, error -110
[ 18.440882] EXT4-fs (sdc6): mounted filesystem with ordered data mode
[ 20.135033] r8169: eth0: link down
[ 20.135502] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 20.182372] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 20.337666] composite sync not supported
[ 20.465165] composite sync not supported
[ 22.191536] composite sync not supported
[ 22.317097] composite sync not supported
[ 22.437724] composite sync not supported
[ 22.989239] hda-intel: IRQ timing workaround is activated for card #1. Suggest a bigger bdl_pos_adj.
[ 28.160510] wlan0: direct probe to AP a2:ea:65:61:30:98 (try 1)
[ 28.361263] wlan0: direct probe to AP a2:ea:65:61:30:98 (try 2)
[ 28.369584] wlan0: direct probe responded
[ 28.369588] wlan0: authenticate with AP a2:ea:65:61:30:98 (try 1)
[ 28.371337] wlan0: authenticated
[ 28.371355] wlan0: associate with AP a2:ea:65:61:30:98 (try 1)
[ 28.373659] wlan0: RX AssocResp from a2:ea:65:61:30:98 (capab=0x411 status=0 aid=1)
[ 28.373662] wlan0: associated
[ 28.374365] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 28.661258] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 29.143106] Intel AES-NI instructions are not detected.
[ 29.178831] padlock: VIA PadLock not detected.
[ 29.281259] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 29.660009] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 31.531261] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 31.760043] usb 1-7: device descriptor read/64, error -110
[ 31.991263] usb 1-7: new high speed USB device using ehci_hcd and address 8
[ 32.281258] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 33.660010] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 35.300009] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 35.560008] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 35.810011] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 36.010008] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 36.188917] composite sync not supported
[ 36.440009] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 36.540021] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 36.790019] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 37.020007] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 37.270008] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 37.660009] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 38.300008] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 38.461253] wlan0: no IPv6 routers present
[ 38.790019] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 39.030007] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 41.770009] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 42.690008] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 43.610008] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 44.530008] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 47.111261] usb 1-7: device descriptor read/64, error -110
[ 47.510010] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 62.340011] usb 1-7: device descriptor read/64, error -110
[ 62.571260] usb 1-7: new high speed USB device using ehci_hcd and address 9
[ 72.991269] usb 1-7: device not accepting address 9, error -110
[ 73.110012] usb 1-7: new high speed USB device using ehci_hcd and address 10
[ 78.240009] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 82.610011] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 83.530009] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 83.531256] usb 1-7: device not accepting address 10, error -110
[ 83.531269] hub 1-0:1.0: unable to enumerate USB device on port 7
[ 83.677211] usblp0: USB Bidirectional printer dev 2 if 1 alt 0 proto 2 vid 0x04A9 pid 0x1714
[ 83.677281] usbcore: registered new interface driver usblp
[ 83.851264] usb 3-1: new low speed USB device using uhci_hcd and address 2
[ 84.079025] usbcore: registered new interface driver hiddev
[ 84.091624] input: HID 04f3:0103 as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input3
[ 84.091743] generic-usb 0003:04F3:0103.0001: input,hidraw0: USB HID v1.10 Keyboard [HID 04f3:0103] on usb-0000:00:1d.1-1/input0
[ 84.115419] input: HID 04f3:0103 as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.1/input/input4
[ 84.115500] generic-usb 0003:04F3:0103.0002: input,hidraw1: USB HID v1.10 Device [HID 04f3:0103] on usb-0000:00:1d.1-1/input1
[ 84.115527] usbcore: registered new interface driver usbhid
[ 84.115529] usbhid: USB HID core driver
[ 84.290032] usb 3-2: new low speed USB device using uhci_hcd and address 3
[ 84.450009] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 84.485401] input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1d.1/usb3/3-2/3-2:1.0/input/input5
[ 84.485494] generic-usb 0003:046D:C050.0003: input,hidraw2: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.1-2/input0
[ 84.770017] usb 4-1: new full speed USB device using uhci_hcd and address 2
[ 85.133914] Bluetooth: Core ver 2.15
[ 85.134132] NET: Registered protocol family 31
[ 85.134135] Bluetooth: HCI device and connection manager initialized
[ 85.134137] Bluetooth: HCI socket layer initialized
[ 85.170712] Bluetooth: Generic Bluetooth USB driver ver 0.6
[ 85.173388] usbcore: registered new interface driver btusb
[ 85.230018] usb 4-2: new low speed USB device using uhci_hcd and address 3
[ 85.371260] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 85.406780] usb 1-2: usbfs: interface 1 claimed by usblp while 'usb' sets config #1
[ 85.500650] Bluetooth: L2CAP ver 2.14
[ 85.500654] Bluetooth: L2CAP socket layer initialized
[ 85.602751] input: Twin USB Joystick as /devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.0/input/input6
[ 85.602869] input: Twin USB Joystick as /devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.0/input/input7
[ 85.602963] pantherlord 0003:0810:0001.0004: input,hidraw3: USB HID v1.10 Joystick [Twin USB Joystick] on usb-0000:00:1d.2-2/input0
[ 85.602973] pantherlord 0003:0810:0001.0004: Force feedback for PantherLord/GreenAsia devices by Anssi Hannula <anssi.hannula@gmail.com>
[ 85.681266] usb 5-1: new full speed USB device using uhci_hcd and address 2
[ 85.691237] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 85.691240] Bluetooth: BNEP filters: protocol multicast
[ 85.722247] Bridge firewalling registered
[ 85.816979] Bluetooth: SCO (Voice Link) ver 0.6
[ 85.816982] Bluetooth: SCO socket layer initialized
[ 86.002072] Bluetooth: RFCOMM TTY layer initialized
[ 86.002077] Bluetooth: RFCOMM socket layer initialized
[ 86.002082] Bluetooth: RFCOMM ver 1.11
[ 87.510013] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 99.358420] composite sync not supported
[ 100.801267] usb 5-1: device descriptor read/64, error -110
[ 116.031268] usb 5-1: device descriptor read/64, error -110
[ 116.260011] usb 5-1: new full speed USB device using uhci_hcd and address 3
[ 118.240010] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 131.381259] usb 5-1: device descriptor read/64, error -110
[ 141.360018] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 142.280016] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 144.460002] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 146.271260] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 146.611267] usb 5-1: device descriptor read/64, error -110
[ 146.840015] usb 5-1: new full speed USB device using uhci_hcd and address 4
[ 147.511260] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 157.261260] usb 5-1: device not accepting address 4, error -110
[ 157.380011] usb 5-1: new full speed USB device using uhci_hcd and address 5
[ 167.801262] usb 5-1: device not accepting address 5, error -110
[ 167.801278] hub 5-0:1.0: unable to enumerate USB device on port 1
[ 259.770012] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 262.452599] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 262.740013] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 263.470014] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 264.654043] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 264.980011] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 265.291629] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 267.440019] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 268.690013] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 269.000015] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 270.560014] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 279.750016] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 283.620015] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 285.274340] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 289.000016] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 289.240012] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 289.450010] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 294.340014] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 295.540026] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 295.800026] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 296.100011] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 298.660011] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 299.351264] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 299.590055] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 304.440015] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 305.170012] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 308.390014] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 308.691462] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 316.040009] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 316.260029] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 316.490016] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 316.770015] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 316.980014] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 317.290025] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 317.600013] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 317.910011] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 318.010011] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 421.540032] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 477.600018] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 479.300014] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 481.820011] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 495.700016] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 502.590012] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 533.240017] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 553.870025] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 557.290025] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 558.830011] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 560.210224] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 562.610013] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 563.110015] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 564.450019] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 565.371262] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 567.311259] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 568.440011] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 570.760013] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 576.280014] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 576.530009] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 577.160007] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 589.960011] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 591.510011] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 615.560012] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 620.570010] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 651.240011] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 666.770007] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 671.770011] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 683.891261] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 684.811258] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 685.731260] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 687.450010] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 688.811259] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 719.240008] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 750.240011] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 781.240013] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 802.620013] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 803.120012] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 804.040032] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 804.540010] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 805.880011] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 807.600012] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 838.210012] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 868.240010] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 899.240012] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 924.300011] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 925.220011] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 927.160012] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 927.370010] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 958.240010] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 989.240010] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).
[ 1020.240014] phy0 -> rt2500pci_set_device_state: Error - Device failed to enter state 1 (-16).Comme je le disais, j'ai installé un noyau patché, mais le problème était là avant, j'espérais pour tout dire qu'il résoudrait tout, mais rien n'a changé :
uname -r
2.6.33-02063303-genericJe suis sous 10.04 64b
avec une Asus P5kpl-am (dernier BIOS, le 518 je crois), 4Go DDR-2, C2D E7400 et Sapphire Radeon HD4830
Par avance, merci.
Dernière modification par Bebertii (Le 14/05/2010, à 22:58)
Hors ligne