Pages : 1
#1 Le 06/08/2010, à 10:08
- sylcab74
AR5001X+ avec Ubuntu 9.04
Je n'arrive pas a me connecter en wifi car les reseaux ne s'affiche pas et network manager n'affiche pas
reseaux sans fil.
[ cabiati@cabiati-laptop:~$ cat /etc/lsb-release
DISTRIB_ID=Ubuntu
DISTRIB_RELEASE=9.04
DISTRIB_CODENAME=jaunty
DISTRIB_DESCRIPTION="Ubuntu 9.04" ]:
[cabiati@cabiati-laptop:~$ lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub]:
[cabiati@cabiati-laptop:~$ lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
cabiati@cabiati-laptop:~$ lspci
00:00.0 Host bridge: ATI Technologies Inc RS200/RS200M AGP Bridge [IGP 340M] (rev 02)
00:01.0 PCI bridge: ATI Technologies Inc PCI Bridge [IGP 340M]
00:03.0 Modem: ALi Corporation M5457 AC'97 Modem Controller
00:04.0 Multimedia audio controller: ALi Corporation M5451 PCI AC-Link Controller Audio Device (rev 02)
00:06.0 Bridge: ALi Corporation M7101 Power Management Controller [PMU]
00:07.0 ISA bridge: ALi Corporation M1533/M1535/M1543 PCI to ISA Bridge [Aladdin IV/V/V+]
00:09.0 Ethernet controller: Atheros Communications Inc. Atheros AR5001X+ Wireless Network Adapter (rev 01)
00:0a.0 CardBus bridge: Texas Instruments PCI7420 CardBus Controller
00:0a.2 FireWire (IEEE 1394): Texas Instruments PCI7x20 1394a-2000 OHCI Two-Port PHY/Link-Layer Controller
00:0a.3 Mass storage controller: Texas Instruments PCI7420/7620 Combo CardBus, 1394a-2000 OHCI and SD/MS-Pro Controller
00:0c.0 USB Controller: NEC Corporation USB (rev 43)
00:0c.1 USB Controller: NEC Corporation USB (rev 43)
00:0c.2 USB Controller: NEC Corporation USB 2.0 (rev 04)
00:0f.0 IDE interface: ALi Corporation M5229 IDE (rev c4)
00:12.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
01:05.0 VGA compatible controller: ATI Technologies Inc M9+ 5C61 [Radeon Mobility 9200 (AGP)] (rev 01)]
[cabiati@cabiati-laptop:~$ lspci -nn | grep -i net
00:09.0 Ethernet controller [0200]: Atheros Communications Inc. Atheros AR5001X+ Wireless Network Adapter [168c:0013] (rev 01)
00:12.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)]
[cabiati@cabiati-laptop:~$ sudo lshw -C network
[sudo] password for cabiati:
*-network:0 UNCLAIMED
description: Ethernet controller
product: Atheros AR5001X+ Wireless Network Adapter
vendor: Atheros Communications Inc.
physical id: 9
bus info: pci@0000:00:09.0
version: 01
width: 32 bits
clock: 33MHz
capabilities: pm cap_list
configuration: latency=168 maxlatency=28 mingnt=10
*-network:1
description: Ethernet interface
product: RTL-8139/8139C/8139C+
vendor: Realtek Semiconductor Co., Ltd.
physical id: 12
bus info: pci@0000:00:12.0
logical name: eth0
version: 10
serial: 08:00:46:cf:f5:7a
size: 100MB/s
capacity: 100MB/s
width: 32 bits
clock: 33MHz
capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=full ip=192.168.1.16 latency=64 link=yes maxlatency=64 mingnt=32 module=8139too multicast=yes port=MII speed=100MB/s
*-network DISABLED
description: Ethernet interface
physical id: 1
logical name: pan0
serial: c6:2e:b3:3b:eb:37
capabilities: ethernet physical
configuration: broadcast=yes driver=bridge driverversion=2.3 firmware=N/A link=yes multicast=yes]
[cabiati@cabiati-laptop:~$ lsmod
Module Size Used by
binfmt_misc 16776 1
radeon 342816 2
drm 96424 3 radeon
bridge 56212 0
stp 10500 1 bridge
bnep 20224 2
input_polldev 11912 0
lp 17156 0
joydev 18368 0
pcmcia 44748 0
tifm_sd 17928 0
ppdev 15620 0
snd_ali5451 27276 3
snd_ac97_codec 112292 1 snd_ali5451
ac97_bus 9856 1 snd_ac97_codec
snd_pcm_oss 46336 0
snd_mixer_oss 22656 1 snd_pcm_oss
snd_pcm 83076 3 snd_ali5451,snd_ac97_codec,snd_pcm_oss
snd_seq_dummy 10756 0
pcspkr 10496 0
psmouse 61972 0
snd_seq_oss 37760 0
serio_raw 13444 0
snd_seq_midi 14336 0
snd_rawmidi 29696 1 snd_seq_midi
snd_seq_midi_event 15104 2 snd_seq_oss,snd_seq_midi
snd_seq 56880 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 29704 2 snd_pcm,snd_seq
snd_seq_device 14988 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
yenta_socket 32396 1
rsrc_nonstatic 19328 1 yenta_socket
tifm_7xx1 13824 0
snd 62756 16 snd_ali5451,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
soundcore 15200 1 snd
tifm_core 15900 2 tifm_sd,tifm_7xx1
ath_pci 99224 0
pcmcia_core 43540 3 pcmcia,yenta_socket,rsrc_nonstatic
wlan 210544 1 ath_pci
ath_hal 198864 1 ath_pci
i2c_ali15x3 14724 0
i2c_ali1535 14212 0
snd_page_alloc 16904 1 snd_pcm
shpchp 40212 0
video 25872 0
output 11008 1 video
sony_laptop 41052 0
parport_pc 40100 1
parport 42220 3 lp,ppdev,parport_pc
ati_agp 14988 1
agpgart 42696 2 drm,ati_agp
8139too 32128 0
8139cp 27776 0
mii 13312 2 8139too,8139cp
ohci1394 38576 0
ieee1394 94660 1 ohci1394
fbcon 46112 0
tileblit 10752 1 fbcon
font 16384 1 fbcon
bitblit 13824 1 fbcon
softcursor 9984 1 bitblit]
[cabiati@cabiati-laptop:~$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
pan0 no wireless extensions.]
[cabiati@cabiati-laptop:~$ ifconfig
eth0 Link encap:Ethernet HWaddr 08:00:46:cf:f5:7a
inet adr:192.168.1.16 Bcast:192.168.1.255 Masque:255.255.255.0
adr inet6: fe80::a00:46ff:fecf:f57a/64 Scope:Lien
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Packets reçus:7830 erreurs:0 :0 overruns:0 frame:0
TX packets:7310 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
Octets reçus:8136480 (8.1 MB) Octets transmis:1068082 (1.0 MB)
Interruption:3 Adresse de base:0x9000
lo Link encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
adr inet6: ::1/128 Scope:Hôte
UP LOOPBACK RUNNING MTU:16436 Metric:1
Packets reçus:0 erreurs:0 :0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
Octets reçus:0 (0.0 B) Octets transmis:0 (0.0 B)]
[cabiati@cabiati-laptop:~$ sudo iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
pan0 Interface doesn't support scanning.]
[cabiati@cabiati-laptop:~$ uname -r -m
2.6.28-19-generic i686]
[cabiati@cabiati-laptop:~$ cat /etc/network/interfaces
auto lo
iface lo inet loopback]
[cabiati@cabiati-laptop:~$ nm-tool
NetworkManager Tool
State: connected
- Device: eth0 [Auto eth0] ----------------------------------------------------
Type: Wired
Driver: 8139too
State: connected
Default: yes
HW Address: 08:00:46:CF:F5:7A
Capabilities:
Carrier Detect: yes
Speed: 100 Mb/s
Wired Properties
Carrier: on
IPv4 Settings:
Address: 192.168.1.16
Prefix: 24 (255.255.255.0)
Gateway: 192.168.1.1
DNS: 192.168.1.1]
Voilà.
Hors ligne
#2 Le 06/08/2010, à 11:32
- toutafai
Re : AR5001X+ avec Ubuntu 9.04
bonjour,
ta carte n'as pas de module (=pilote) pour la gerer, installe-le avec un
sudo apt-get install linux-backport-modules-karmic
puis reboot ta carte wifi devrait apparaitre
Tombé dans l'informatique étant petit, j'en ai fait mon métier. Utilisateur d'Ubuntu depuis novembre 2006, actuellement sous 20.04 x64 (Que d'évolution
depuis Dapper Drake ! Ça rajeunit pas ^^^).
Hors ligne
#3 Le 06/08/2010, à 11:51
- Nexus6
Re : AR5001X+ avec Ubuntu 9.04
Salut!
Pour une SRC Ubiquiti, qui est le meilleur adaptateur Wifi au monde selon moi (rien que ça!), vous pouvez utiliser le driver hal (propriétaire) ou bien le driver ath5k (libre), je vous conseille de passer sous ath5k.
@toutafai est de bon conseil :
# sudo apt-get install linux-backport-modules-karmic
Dans le gestionnaire de pilotes propriétaires, vous ne devriez plus voir le driver atheros :
- Atheros Hardware Access Layer (HAL)
Il faut désactiver ce pilote propriétaires dans cette interface si il est toujours actif.
Cela blacklist ath_pci dans un des fichiers .conf du dossier /etc/modprobe.d/
root@nexus:/etc/modprobe.d# cat blacklist-ath_pci.conf
--
# For some Atheros 5K RF MACs, the madwifi driver loads buts fails to
# correctly initialize the hardware, leaving it in a state from
# which ath5k cannot recover. To prevent this condition, stop
# madwifi from loading by default. Use Jockey to select one driver
# or the other. (Ubuntu: #315056, #323830)
blacklist ath_pci
--
Dans le fichier /etc/modules ajouter ath5k (mettre un '#' devant ath_pci si cette ligne est présente, ça le désactive!) et au prochain reboot ath5k devrait être pris en compte de façon permanent.
--
# /etc/modules: kernel modules to load at boot time.
#
# This file contains the names of kernel modules that should be loaded
# at boot time, one per line. Lines beginning with "#" are ignored.
ath5k
lp
#ndiswrapper
--
Retirer la carte du slot PCMCIA, attendre 5s et remettez-là à sa place...
/Nexus6
--
!
Dernière modification par Nexus6 (Le 06/08/2010, à 12:00)
Hors ligne
#4 Le 06/08/2010, à 12:11
- sylcab74
Re : AR5001X+ avec Ubuntu 9.04
Bonjour toutafal j'ai essayer d'installer le module mais celà n'a pas marché voilà le resultat
[cabiati@cabiati-laptop:~$ sudo apt-get install linux-backport-modules-karmic
[sudo] password for cabiati:
Lecture des listes de paquets... Fait
Construction de l'arbre des dépendances
Lecture des informations d'état... Fait
E: Impossible de trouver le paquet linux-backport-modules-karmic]
Dernière modification par sylcab74 (Le 06/08/2010, à 12:17)
Hors ligne
#5 Le 06/08/2010, à 12:57
- Nexus6
Re : AR5001X+ avec Ubuntu 9.04
Re,
Alors installez manuellement ath5k :
compat-wireless :
# aptitude install libnl1
# aptitude install libnl-dev
Donc pour installer le dernier driver du jour (enfin de la nuit ) :
# wget http://wireless.kernel.org/download/compat-wireless-2.6/compat-wireless-2010-08-05.tar.bz2
Unbzip file :
# tar -jxvf compat-wireless-2010-08-05.tar.bz2
Change dir :
# cd compat-wireless-2010-08-05
Compilation :
# make
Installation :
# make install
Si il vous manque des packages à la compilation, utiliser aptitude avec la commande search (et le wildcard *) :
# aptitude search libnlx*
/Nexus6
--
!
Dernière modification par Nexus6 (Le 06/08/2010, à 12:57)
Hors ligne
#6 Le 06/08/2010, à 13:52
- sylcab74
Re : AR5001X+ avec Ubuntu 9.04
est ce que le pilote madwifi sert a quelque chose??
Hors ligne
#7 Le 06/08/2010, à 18:45
- toutafai
Re : AR5001X+ avec Ubuntu 9.04
bizarre qu'il n'est pas trouvé ce paquet....tu as activé les dépots backport ? (a vérifier via synaptic, configuration > Dépots > onglet "Mise à jour"). tu été connecté par un cable ?
oui, madwifi est un autre module pouvant gerer ton wifi, mais mieux vaut utiliser le module libre ath5k, comme le dit Nexus6..a qui je laisse la main, mon exp de "madwifi" est un peu rouillé, je reste abonné au post en cas de besoin
Tombé dans l'informatique étant petit, j'en ai fait mon métier. Utilisateur d'Ubuntu depuis novembre 2006, actuellement sous 20.04 x64 (Que d'évolution
depuis Dapper Drake ! Ça rajeunit pas ^^^).
Hors ligne
Pages : 1