clé USB non reconnue

laborde · Le 09/03/2008, à 15:01

merci pour les explications en plus du coup de main.

laborde@laborde-desktop:~$ lspci && lsusb
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 761/M761 Host (rev 02)
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge
00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS964 [MuTIOL Media IO] (rev 36)
00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev 01)
00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS] AC'97 Sound Controller (rev a0)
00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f)
00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f)
00:03.2 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f)
00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0 Controller
00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 PCI Fast Ethernet (rev 91)
00:05.0 IDE interface: Silicon Integrated Systems [SiS] SATA (rev 01)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:00.0 VGA compatible controller: nVidia Corporation G72 [GeForce 7300 SE] (rev a1)
Bus 004 Device 001: ID 0000:0000
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 004: ID 058f:9360 Alcor Micro Corp. 8-in-1 Media Card Reader
Bus 001 Device 001: ID 0000:0000

laborde@laborde-desktop:~$ lsmod |grep usb
usb_storage 73024 1
ide_core 116804 1 usb_storage
libusual 18448 1 usb_storage
usbcore 138632 5 usb_storage,libusual,ehci_hcd,ohci_hcd
scsi_mod 147084 5 usb_storage,sd_mod,sg,sr_mod,libata

Voilà voilà...

laborde · Le 09/03/2008, à 15:37

laborde@laborde-desktop:~$ sudo fdisk -l
[sudo] password for laborde:

Disque /dev/sda: 160.0 Go, 160041885696 octets
255 heads, 63 sectors/track, 19457 cylinders
Units = cylindres of 16065 * 512 = 8225280 bytes
Disk identifier: 0xecb68b2d

Périphérique Amorce Début Fin Blocs Id Système
/dev/sda1 * 1 1950 15663343+ 83 Linux
/dev/sda2 1951 2193 1951897+ 82 Linux swap / Solaris
/dev/sda3 2194 10884 69810457+ 83 Linux
/dev/sda4 10885 19457 68862622+ 5 Extended
/dev/sda5 10885 15976 40901458+ 83 Linux
/dev/sda6 15977 19457 27961101 83 Linux

toutafai · Le 09/03/2008, à 17:24

pourtant tout a l'air ok d'apres le lspci et le lsmod...(je connais pas spécifiquement ton matériel, mais encore une fois ca a l'air ok)

quand tu as fait le sudo fdisk-l t'avait la clef de branché ?

Autre piste, vérifie que ton utilisateur est autorisé a "utiliser les péripheriques externes de stockage automatiquement" (menu "systeme", administration, "utilisateur et groupes", double clique sur ton utilisateur et verifie que la case est cochée, sinon coche la, valide, debranche la clef si branchée, deconnecte-toi et re branche la clef.

tu utilise quel version ubuntu ?

laborde · Le 09/03/2008, à 18:56

oui la clée était branchée quand j'ai fait le fdisk-l

Je le refais avec sans la clé pui après avec la clé

laborde@laborde-desktop:~$ sudo fdisk -l

Disque /dev/sda: 160.0 Go, 160041885696 octets
255 heads, 63 sectors/track, 19457 cylinders
Units = cylindres of 16065 * 512 = 8225280 bytes
Disk identifier: 0xecb68b2d

Périphérique Amorce Début Fin Blocs Id Système
/dev/sda1 * 1 1950 15663343+ 83 Linux
/dev/sda2 1951 2193 1951897+ 82 Linux swap / Solaris
/dev/sda3 2194 10884 69810457+ 83 Linux
/dev/sda4 10885 19457 68862622+ 5 Extended
/dev/sda5 10885 15976 40901458+ 83 Linux
/dev/sda6 15977 19457 27961101 83 Linux

Puis avec la clé

laborde@laborde-desktop:~$ sudo fdisk -l

Disque /dev/sda: 160.0 Go, 160041885696 octets
255 heads, 63 sectors/track, 19457 cylinders
Units = cylindres of 16065 * 512 = 8225280 bytes
Disk identifier: 0xecb68b2d

Périphérique Amorce Début Fin Blocs Id Système
/dev/sda1 * 1 1950 15663343+ 83 Linux
/dev/sda2 1951 2193 1951897+ 82 Linux swap / Solaris
/dev/sda3 2194 10884 69810457+ 83 Linux
/dev/sda4 10885 19457 68862622+ 5 Extended
/dev/sda5 10885 15976 40901458+ 83 Linux
/dev/sda6 15977 19457 27961101 83 Linux

C'eszt la même chose

sinon j'utilise gutsy, et la case "utiliser les péripheriques externes de stockage automatiquement" est cochée...

toutafai · Le 09/03/2008, à 22:24

la je seche .....

reposte un "dmesg" (sans le | tail) apres a voir rebranché ta clef et attendu quelque secondes..

essaye aussi sur un autre port usb ...

si t'as un windope sous la main, test la pour voir.

laborde · Le 10/03/2008, à 00:47

voila la commande dmesg

laborde@laborde-desktop:~$ dmesg
[ 0.000000] Linux version 2.6.22-14-generic (buildd@terranova) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Tue Feb 12 07:42:25 UTC 2008 (Ubuntu 2.6.22-14.52-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000001ffd0000 (usable)
[ 0.000000] BIOS-e820: 000000001ffd0000 - 000000001ffde000 (ACPI data)
[ 0.000000] BIOS-e820: 000000001ffde000 - 0000000020000000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 511MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000ff780
[ 0.000000] Entering add_active_range(0, 0, 131024) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 131024
[ 0.000000] HighMem 131024 -> 131024
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 131024
[ 0.000000] On node 0 totalpages: 131024
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 991 pages used for memmap
[ 0.000000] Normal zone: 125937 pages, LIFO batch:31
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP signature @ 0xC00F8250 checksum 0
[ 0.000000] ACPI: RSDP 000F8250, 0014 (r0 ACPIAM)
[ 0.000000] ACPI: RSDT 1FFD0000, 0034 (r1 A M I OEMRSDT 3000623 MSFT 97)
[ 0.000000] ACPI: FACP 1FFD0200, 0084 (r2 A M I OEMFACP 3000623 MSFT 97)
[ 0.000000] ACPI: DSDT 1FFD0430, 42E0 (r1 R02 R02A1 0 INTL 2002026)
[ 0.000000] ACPI: FACS 1FFDE000, 0040
[ 0.000000] ACPI: APIC 1FFD0390, 0054 (r1 A M I OEMAPIC 3000623 MSFT 97)
[ 0.000000] ACPI: MCFG 1FFD03F0, 003C (r1 A M I OEMMCFG 3000623 MSFT 97)
[ 0.000000] ACPI: OEMB 1FFDE040, 0047 (r1 A M I AMI_OEM 3000623 MSFT 97)
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:12 APIC version 16
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 30000000 (gap: 20000000:df780000)
[ 0.000000] Built 1 zonelists. Total pages: 130001
[ 0.000000] Kernel command line: root=UUID=51db1024-bd0c-44c4-a5ad-d4b54c0a45b9 ro quiet splash locale=fr_FR
[ 0.000000] mapped APIC to ffffd000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffc000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] Detected 1800.132 MHz processor.
[ 16.676933] Console: colour VGA+ 80x25
[ 16.677118] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 16.677338] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 16.686416] Memory: 508044k/524096k available (2015k kernel code, 15432k reserved, 915k data, 364k init, 0k highmem)
[ 16.686427] virtual kernel memory layout:
[ 16.686428] fixmap : 0xfff4d000 - 0xfffff000 ( 712 kB)
[ 16.686430] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 16.686431] vmalloc : 0xe0800000 - 0xff7fe000 ( 495 MB)
[ 16.686432] lowmem : 0xc0000000 - 0xdffd0000 ( 511 MB)
[ 16.686434] .init : 0xc03e3000 - 0xc043e000 ( 364 kB)
[ 16.686435] .data : 0xc02f7e86 - 0xc03dce84 ( 915 kB)
[ 16.686436] .text : 0xc0100000 - 0xc02f7e86 (2015 kB)
[ 16.686439] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 16.686473] SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
[ 16.766372] Calibrating delay using timer specific routine.. 3602.07 BogoMIPS (lpj=7204141)
[ 16.766393] Security Framework v1.0.0 initialized
[ 16.766398] SELinux: Disabled at boot.
[ 16.766410] Mount-cache hash table entries: 512
[ 16.766509] CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001
[ 16.766517] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 16.766520] CPU: L2 Cache: 256K (64 bytes/line)
[ 16.766523] CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410 00000001 00000000 00000001
[ 16.766531] Compat vDSO mapped to ffffe000.
[ 16.766540] Checking 'hlt' instruction... OK.
[ 16.782457] SMP alternatives: switching to UP code
[ 16.782638] Freeing SMP alternatives: 11k freed
[ 16.782916] Early unpacking initramfs... done
[ 17.097169] ACPI: Core revision 20070126
[ 17.097234] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 17.098974] CPU0: AMD Sempron(tm) Processor 3100+ stepping 02
[ 17.098991] Total of 1 processors activated (3602.07 BogoMIPS).
[ 17.099084] ENABLING IO-APIC IRQs
[ 17.099246] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 17.245714] Brought up 1 CPUs
[ 17.245813] Booting paravirtualized kernel on bare hardware
[ 17.245874] Time: 16:58:26 Date: 02/09/108
[ 17.245896] NET: Registered protocol family 16
[ 17.245977] EISA bus registered
[ 17.245988] ACPI: bus type pci registered
[ 17.246650] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=1
[ 17.246653] PCI: Using configuration type 1
[ 17.246654] Setting up standard PCI resources
[ 17.253880] ACPI: EC: Look up EC in DSDT
[ 17.258572] ACPI: Interpreter enabled
[ 17.258575] ACPI: (supports S0 S1 S3 S4 S5)
[ 17.258590] ACPI: Using IOAPIC for interrupt routing
[ 17.266632] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 17.266638] PCI: Probing PCI hardware (bus 00)
[ 17.267141] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 17.273949] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 *10 11 12 14 15)
[ 17.274075] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 7 10 11 12 14 15)
[ 17.274172] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 *11 12 14 15)
[ 17.274291] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 10 11 12 14 15)
[ 17.274387] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 7 10 11 12 14 15)
[ 17.274484] ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 5 7 10 11 12 14 15)
[ 17.274592] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 7 10 11 12 14 15)
[ 17.274688] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 7 10 11 12 14 15)
[ 17.274763] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 17.274776] pnp: PnP ACPI init
[ 17.274784] ACPI: bus type pnp registered
[ 17.279788] pnp: PnP ACPI: found 14 devices
[ 17.279791] ACPI: ACPI bus type pnp unregistered
[ 17.279795] PnPBIOS: Disabled by ACPI PNP
[ 17.279841] PCI: Using ACPI for IRQ routing
[ 17.279844] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 17.282415] NET: Registered protocol family 8
[ 17.282418] NET: Registered protocol family 20
[ 17.282480] pnp: 00:09: ioport range 0xa00-0xa0f has been reserved
[ 17.282483] pnp: 00:09: ioport range 0xa10-0xa1f has been reserved
[ 17.282485] pnp: 00:09: ioport range 0xa20-0xa2f has been reserved
[ 17.282488] pnp: 00:09: ioport range 0xa30-0xa3f has been reserved
[ 17.282494] pnp: 00:0a: iomem range 0xffb80000-0xffbfffff could not be reserved
[ 17.282497] pnp: 00:0a: iomem range 0xfff80000-0xffffffff could not be reserved
[ 17.282500] pnp: 00:0a: iomem range 0xffe80000-0xffefffff could not be reserved
[ 17.282503] pnp: 00:0a: iomem range 0xfed00000-0xfed003ff has been reserved
[ 17.282508] pnp: 00:0b: iomem range 0xfec00000-0xfec00fff has been reserved
[ 17.282511] pnp: 00:0b: iomem range 0xfee00000-0xfee00fff has been reserved
[ 17.282516] pnp: 00:0c: iomem range 0xe0000000-0xefffffff has been reserved
[ 17.282521] pnp: 00:0d: iomem range 0x0-0x9ffff could not be reserved
[ 17.282524] pnp: 00:0d: iomem range 0xc0000-0xcffff could not be reserved
[ 17.282527] pnp: 00:0d: iomem range 0xe0000-0xfffff could not be reserved
[ 17.282530] pnp: 00:0d: iomem range 0x100000-0x1fffffff could not be reserved
[ 17.285626] Time: tsc clocksource has been installed.
[ 17.312719] PCI: Bridge: 0000:00:01.0
[ 17.312721] IO window: disabled.
[ 17.312725] MEM window: fc000000-febfffff
[ 17.312729] PREFETCH window: d8000000-dfffffff
[ 17.312748] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 17.312759] NET: Registered protocol family 2
[ 17.349572] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 17.349613] TCP established hash table entries: 16384 (order: 5, 196608 bytes)
[ 17.349758] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 17.349867] TCP: Hash tables configured (established 16384 bind 16384)
[ 17.349870] TCP reno registered
[ 17.361639] checking if image is initramfs... it is
[ 17.812863] Switched to high resolution mode on CPU 0
[ 17.983042] Freeing initrd memory: 7062k freed
[ 17.983379] audit: initializing netlink socket (disabled)
[ 17.983391] audit(1205081906.996:1): initialized
[ 17.984934] VFS: Disk quotas dquot_6.5.1
[ 17.984978] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 17.985058] io scheduler noop registered
[ 17.985060] io scheduler anticipatory registered
[ 17.985062] io scheduler deadline registered
[ 17.985076] io scheduler cfq registered (default)
[ 18.040470] Boot video device is 0000:01:00.0
[ 18.040537] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 18.040567] assign_interrupt_mode Found MSI capability
[ 18.040570] Allocate Port Service[0000:00:01.0:pcie00]
[ 18.040687] isapnp: Scanning for PnP cards...
[ 18.393693] isapnp: No Plug & Play device found
[ 18.416909] Real Time Clock Driver v1.12ac
[ 18.416979] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 18.417064] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 18.417763] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 18.418339] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 18.418514] input: Macintosh mouse button emulation as /class/input/input0
[ 18.418576] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 18.418838] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 18.418843] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 18.418964] mice: PS/2 mouse device common for all mice
[ 18.419057] EISA: Probing bus 0 at eisa.0
[ 18.419091] EISA: Detected 0 cards.
[ 18.419233] TCP cubic registered
[ 18.419249] NET: Registered protocol family 1
[ 18.419269] Using IPI No-Shortcut mode
[ 18.419400] Magic number: 0:795:994
[ 18.419410] hash matches device ttyd7
[ 18.419419] hash matches device ttyaa
[ 18.419769] Freeing unused kernel memory: 364k freed
[ 18.492645] input: AT Translated Set 2 keyboard as /class/input/input1
[ 19.617120] AppArmor: AppArmor initialized<5>audit(1205081908.496:2): type=1505 info="AppArmor initialized" pid=1191
[ 19.622784] fuse init (API version 7.8)
[ 19.626832] Failure registering capabilities with primary security module.
[ 19.641898] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 19.642687] ACPI: Thermal Zone [THRM] (-269 C)
[ 20.122120] SCSI subsystem initialized
[ 20.126424] libata version 2.21 loaded.
[ 20.129433] pata_sis 0000:00:02.5: version 0.5.1
[ 20.129549] scsi0 : pata_sis
[ 20.129589] scsi1 : pata_sis
[ 20.129674] ata1: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001ffa0 irq 14
[ 20.129678] ata2: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001ffa8 irq 15
[ 20.171478] usbcore: registered new interface driver usbfs
[ 20.171500] usbcore: registered new interface driver hub
[ 20.171518] usbcore: registered new device driver usb
[ 20.175383] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 20.209878] sis900.c: v1.08.10 Apr. 2 2006
[ 20.620690] ata2.00: ATAPI: LITE-ON DVDRW SHW-160P6S, PRS2, max UDMA/66
[ 20.620697] ata2.00: limited to UDMA/33 due to 40-wire cable
[ 20.808397] ata2.00: configured for UDMA/33
[ 20.809247] scsi 1:0:0:0: CD-ROM LITE-ON DVDRW SHW-160P6S PRS2 PQ: 0 ANSI: 5
[ 20.809410] ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 16
[ 20.809422] ohci_hcd 0000:00:03.0: OHCI Host Controller
[ 20.809563] ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
[ 20.809578] ohci_hcd 0000:00:03.0: irq 16, io mem 0xfbfff000
[ 20.825737] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[ 20.825743] Uniform CD-ROM driver Revision: 3.20
[ 20.825930] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 20.829906] sr 1:0:0:0: Attached scsi generic sg0 type 5
[ 20.866185] usb usb1: configuration #1 chosen from 1 choice
[ 20.866211] hub 1-0:1.0: USB hub found
[ 20.866220] hub 1-0:1.0: 3 ports detected
[ 20.968040] ACPI: PCI Interrupt 0000:00:03.1[b] -> GSI 21 (level, low) -> IRQ 17
[ 20.968054] ohci_hcd 0000:00:03.1: OHCI Host Controller
[ 20.968075] ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
[ 20.968090] ohci_hcd 0000:00:03.1: irq 17, io mem 0xfbffe000
[ 21.025933] usb usb2: configuration #1 chosen from 1 choice
[ 21.025958] hub 2-0:1.0: USB hub found
[ 21.025966] hub 2-0:1.0: 3 ports detected
[ 21.127778] ACPI: PCI Interrupt 0000:00:03.2[C] -> GSI 22 (level, low) -> IRQ 18
[ 21.127792] ohci_hcd 0000:00:03.2: OHCI Host Controller
[ 21.127815] ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
[ 21.127828] ohci_hcd 0000:00:03.2: irq 18, io mem 0xfbffd000
[ 21.185686] usb usb3: configuration #1 chosen from 1 choice
[ 21.185712] hub 3-0:1.0: USB hub found
[ 21.185721] hub 3-0:1.0: 2 ports detected
[ 21.271458] usb 1-3: new full speed USB device using ohci_hcd and address 2
[ 21.287932] ACPI: PCI Interrupt 0000:00:03.3[D] -> GSI 23 (level, low) -> IRQ 19
[ 21.287944] ehci_hcd 0000:00:03.3: EHCI Host Controller
[ 21.287971] ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 4
[ 21.288001] PCI: cache line size of 64 is not supported by device 0000:00:03.3
[ 21.288011] ehci_hcd 0000:00:03.3: irq 19, io mem 0xfbffc000
[ 21.447196] ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 21.447286] usb usb4: configuration #1 chosen from 1 choice
[ 21.447313] hub 4-0:1.0: USB hub found
[ 21.447319] hub 4-0:1.0: 8 ports detected
[ 21.551216] ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 19 (level, low) -> IRQ 20
[ 21.561592] 0000:00:04.0: Realtek RTL8201 PHY transceiver found at address 31.
[ 21.561902] 0000:00:04.0: Using transceiver found at address 31 as default
[ 21.562717] eth0: SiS 900 PCI Fast Ethernet at 0xe000, IRQ 20, 00:16:ec:9b:58:3a.
[ 21.562788] sata_sis 0000:00:05.0: version 0.8
[ 21.562803] ACPI: PCI Interrupt 0000:00:05.0[A] -> GSI 17 (level, low) -> IRQ 21
[ 21.562808] sata_sis 0000:00:05.0: Detected SiS 180/181/964 chipset in SATA mode
[ 21.562882] scsi2 : sata_sis
[ 21.562919] scsi3 : sata_sis
[ 21.562982] ata3: SATA max UDMA/133 cmd 0x0001d800 ctl 0x0001d402 bmdma 0x0001c400 irq 21
[ 21.562988] ata4: SATA max UDMA/133 cmd 0x0001d000 ctl 0x0001c802 bmdma 0x0001c408 irq 21
[ 21.854554] usb 1-3: device not accepting address 2, error -62
[ 22.030308] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 22.084596] ata3.00: ATA-7: ST3160812AS, 3.AAE, max UDMA/133
[ 22.084599] ata3.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 22.151124] ata3.00: configured for UDMA/133
[ 22.461626] ata4: SATA link down (SStatus 0 SControl 300)
[ 22.472273] scsi 2:0:0:0: Direct-Access ATA ST3160812AS 3.AA PQ: 0 ANSI: 5
[ 22.472694] scsi 2:0:0:0: Attached scsi generic sg1 type 0
[ 22.479146] sd 2:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 22.479159] sd 2:0:0:0: [sda] Write Protect is off
[ 22.479162] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 22.479177] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 22.479227] sd 2:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 22.479235] sd 2:0:0:0: [sda] Write Protect is off
[ 22.479238] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 22.479250] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 22.479255] sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
[ 22.535024] sd 2:0:0:0: [sda] Attached SCSI disk
[ 22.581437] usb 1-3: new full speed USB device using ohci_hcd and address 4
[ 22.765734] Attempting manual resume
[ 22.765738] swsusp: Resume From Partition 8:2
[ 22.765740] PM: Checking swsusp image.
[ 22.765938] PM: Resume from disk failed.
[ 22.796227] usb 1-3: configuration #1 chosen from 1 choice
[ 22.798113] kjournald starting. Commit interval 5 seconds
[ 22.798127] EXT3-fs: mounted filesystem with ordered data mode.
[ 22.809275] usbcore: registered new interface driver libusual
[ 22.815116] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 22.815121] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 22.817547] Initializing USB Mass Storage driver...
[ 22.817604] scsi4 : SCSI emulation for USB Mass Storage devices
[ 22.833872] usb-storage: device found at 4
[ 22.833875] usb-storage: waiting for device to settle before scanning
[ 22.833900] usbcore: registered new interface driver usb-storage
[ 22.833903] USB Mass Storage support registered.
[ 27.826492] usb-storage: device scan complete
[ 27.834040] scsi 4:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
[ 27.841327] scsi 4:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
[ 27.847715] scsi 4:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
[ 27.855157] scsi 4:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
[ 27.868779] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[ 27.868822] sd 4:0:0:0: Attached scsi generic sg2 type 0
[ 27.880271] sd 4:0:0:1: [sdc] Attached SCSI removable disk
[ 27.880311] sd 4:0:0:1: Attached scsi generic sg3 type 0
[ 27.890822] sd 4:0:0:2: [sdd] Attached SCSI removable disk
[ 27.890865] sd 4:0:0:2: Attached scsi generic sg4 type 0
[ 27.902051] sd 4:0:0:3: [sde] Attached SCSI removable disk
[ 27.902098] sd 4:0:0:3: Attached scsi generic sg5 type 0
[ 28.899131] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 29.071713] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 29.627870] Linux agpgart interface v0.102 (c) Dave Jones
[ 30.104411] input: PC Speaker as /class/input/input2
[ 30.140389] nvidia: module license 'NVIDIA' taints kernel.
[ 30.457203] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 22
[ 30.457214] PCI: Setting latency timer of device 0000:01:00.0 to 64
[ 30.457570] NVRM: loading NVIDIA UNIX x86 Kernel Module 100.14.19 Wed Sep 12 14:12:24 PDT 2007
[ 30.971862] ACPI: PCI Interrupt 0000:00:02.7[C] -> GSI 18 (level, low) -> IRQ 23
[ 31.043345] input: ImPS/2 Generic Wheel Mouse as /class/input/input3
[ 31.046344] parport_pc 00:08: reported by Plug and Play ACPI
[ 31.046412] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 31.147606] parport0: Printer, HEWLETT-PACKARD DESKJET 870C
[ 31.391791] intel8x0_measure_ac97_clock: measured 52414 usecs
[ 31.391794] intel8x0: clocking to 48000
[ 32.365034] lp0: using parport0 (interrupt-driven).
[ 32.407762] Adding 1951888k swap on /dev/sda2. Priority:-1 extents:1 across:1951888k
[ 32.713753] EXT3 FS on sda1, internal journal
[ 34.567500] kjournald starting. Commit interval 5 seconds
[ 34.567650] EXT3 FS on sda3, internal journal
[ 34.567655] EXT3-fs: mounted filesystem with ordered data mode.
[ 34.593289] kjournald starting. Commit interval 5 seconds
[ 34.593434] EXT3 FS on sda5, internal journal
[ 34.593438] EXT3-fs: mounted filesystem with ordered data mode.
[ 34.618584] kjournald starting. Commit interval 5 seconds
[ 34.618722] EXT3 FS on sda6, internal journal
[ 34.618726] EXT3-fs: mounted filesystem with ordered data mode.
[ 35.426149] No dock devices found.
[ 35.498806] input: Power Button (FF) as /class/input/input4
[ 35.502785] ACPI: Power Button (FF) [PWRF]
[ 35.538334] input: Power Button (CM) as /class/input/input5
[ 35.542306] ACPI: Power Button (CM) [PWRB]
[ 35.760223] powernow-k8: Found 1 AMD Sempron(tm) Processor 3100+ processors (version 2.00.00)
[ 35.760254] powernow-k8: 0 : fid 0xa (1800 MHz), vid 0x6
[ 35.760257] powernow-k8: 1 : fid 0x2 (1000 MHz), vid 0x12
[ 36.700449] ppdev: user-space parallel port driver
[ 36.903847] audit(1205081926.476:3): type=1503 operation="inode_permission" requested_mask="a" denied_mask="a" name="/dev/tty" pid=4655 profile="/usr/sbin/cupsd"
[ 36.948247] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 36.948252] apm: overridden by ACPI.
[ 37.157731] Failure registering capabilities with primary security module.
[ 37.348989] Bluetooth: Core ver 2.11
[ 37.349093] NET: Registered protocol family 31
[ 37.349095] Bluetooth: HCI device and connection manager initialized
[ 37.349099] Bluetooth: HCI socket layer initialized
[ 37.369279] Bluetooth: L2CAP ver 2.8
[ 37.369283] Bluetooth: L2CAP socket layer initialized
[ 37.441414] Bluetooth: RFCOMM socket layer initialized
[ 37.441497] Bluetooth: RFCOMM TTY layer initialized
[ 37.441500] Bluetooth: RFCOMM ver 1.8
[ 38.721356] eth0: Media Link On 100mbps full-duplex
[ 21.980000] Marking TSC unstable due to: cpufreq changes.
[ 21.984000] Time: acpi_pm clocksource has been installed.
[ 22.520000] Clocksource tsc unstable (delta = -222245039 ns)
[ 25.100000] NET: Registered protocol family 17
[ 27.052000] NET: Registered protocol family 10
[ 27.052000] lo: Disabled Privacy Extensions
[ 37.112000] eth0: no IPv6 routers present

toutafai · Le 10/03/2008, à 01:00

ouaips, ben je voit pas , désolé, essaye ta clef sous windows pour voir..

essaye aussi en déranchant ton lecteur de carte usb (j'voit pas pourquoi mais bon...)

Dernière modification par toutafai (Le 10/03/2008, à 01:04)

laborde · Le 10/03/2008, à 21:17

Merci tout de même d'avoir pris du temps pour moi.

toutafai · Le 10/03/2008, à 21:54

pas de pb, de rien,.

si tu trouve n'hesite pas a revenir le dire, histoire que je me couche moins bete :-)

CISSE · Le 11/04/2008, à 01:02

bonjour
Je narrive pas a utiliser ma cle usb 1gb depuis que jai supprime un programme suspect detecte par avira antivirus. Le systeme de fichier est inconnu.
Je vous remercie davance pour votre aide.

laborde · Le 11/04/2008, à 02:09

dis en un peu plus, ta clée est détecté?

toufku · Le 11/04/2008, à 11:57

@cisse
tu peut voir et remettre le bon format avec gparted
mais attention a prendre le bon peripherique sinon c'est le disque dur que tu formate.
le système usuel est le fat32 si tu te sert aussi de ta clé sous windows.

erz · Le 19/02/2009, à 19:54

Bonjour à tous.
Je me permets de reprendre ce sujet car j'ai un problème similaire.

Je n'arrive pas a accéder ma clé usb. Elle marchait pourtant très bien il y a quelque jour. J'ai essayer de m'en servir pour flasher le bios. J'ai donc tenter de lire ma clé depuis le bios (EZ flash 2 d'asus) mais elle n'apparaissais pas.
Je l'ai ensuite branché sur mon ubuntu. Mais rien. Elle s'allume mais je ne peux pas y accéder. Sous windows elle est vu comme un lecteur de cd.
lusb me retourne :

Bus 007 Device 003: ID 5986:0102 Acer, Inc Crystal Eye webcam
Bus 007 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 003: ID 13fe:1d00 Kingston Technology Company Inc. DataTraveler 2.0 1GB/4GB Flash Drive / Patriot Xporter 4GB Flash Drive
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 003: ID 046d:c50e Logitech, Inc. MX-1000 Cordless Mouse Receiver
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

Elle apparait clairement sur le bus 3.

Et dmesg | tail m'affiche :

[  969.977267] usb 3-1: USB disconnect, address 2
[  972.896186] usb 3-1: new high speed USB device using ehci_hcd and address 3
[  973.040589] usb 3-1: configuration #1 chosen from 1 choice
[  973.041860] scsi6 : SCSI emulation for USB Mass Storage devices
[  973.042657] usb-storage: device found at 3
[  973.042665] usb-storage: waiting for device to settle before scanning
[  978.040490] usb-storage: device scan complete
[  978.089610] scsi 6:0:0:0: Direct-Access              USB DISK 30X     1.00 PQ: 0 ANSI: 0 CCS
[  978.099242] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[  978.099879] sd 6:0:0:0: Attached scsi generic sg2 type 0

Je dirais bien que tous a l'air normal mais bon.
Et pour finir elle n'apparait pas sous Gparted.
Si quelqu'un a une idée je suis preneur.

Merci d'avance.

erz · Le 20/02/2009, à 10:17

Si une âme charitable voulais bien jeter un coup d'œil à mon problème ça serais sympa.:D

nico_h · Le 23/02/2011, à 14:14

Salut tous, un gros "up" sur ce sujet où j'ai un problème similaire : un ami m'a donné une clé usb pour "réparation". Sous Windows elle est reconnue comme un CD et sous ubuntu il ne se passe pas grand-chose.

Voici quelques résultats (en résumé elle n'est "vue" que par lsusb et dans dmesg).

La clé est branchée (depuis un moment) pendant l'exécution de ces commandes :

# ls /media
#

# df -h
Sys. de fich.            Taille  Uti. Disp. Uti% Monté sur
/dev/sda7             7,7G  5,8G  1,6G  79% /
none                  1,9G  320K  1,9G   1% /dev
none                  1,9G  684K  1,9G   1% /dev/shm
none                  1,9G  220K  1,9G   1% /var/run
none                  1,9G     0  1,9G   0% /var/lock
/dev/sda9             178G  148G   21G  88% /home
/home/nico/.Private   178G  148G   21G  88% /home/nico
#

(sda est le disque dur de mon PC)

# mount
/dev/sda7 on / type ext3 (rw,errors=remount-ro,commit=0)
proc on /proc type proc (rw,noexec,nosuid,nodev)
none on /sys type sysfs (rw,noexec,nosuid,nodev)
fusectl on /sys/fs/fuse/connections type fusectl (rw)
none on /sys/kernel/debug type debugfs (rw)
none on /sys/kernel/security type securityfs (rw)
none on /dev type devtmpfs (rw,mode=0755)
none on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620)
none on /dev/shm type tmpfs (rw,nosuid,nodev)
none on /var/run type tmpfs (rw,nosuid,mode=0755)
none on /var/lock type tmpfs (rw,noexec,nosuid,nodev)
/dev/sda9 on /home type ext3 (rw,commit=0)
binfmt_misc on /proc/sys/fs/binfmt_misc type binfmt_misc (rw,noexec,nosuid,nodev)
/home/nico/.Private on /home/nico type ecryptfs (ecryptfs_sig=***,ecryptfs_fnek_sig=***,ecryptfs_cipher=aes,ecryptfs_key_bytes=16)
gvfs-fuse-daemon on /home/nico/.gvfs type fuse.gvfs-fuse-daemon (rw,nosuid,nodev,user=nico)
#

# fdisk -ul

Disque /dev/sda: 320.1 Go, 320072933376 octets
255 têtes, 63 secteurs/piste, 38913 cylindres, total 625142448 secteurs
Unités = secteurs de 1 * 512 = 512 octets
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Identifiant de disque : 0x00038fad

Périphérique Amorce  Début        Fin      Blocs     Id  Système
/dev/sda1   *          63    19535039     9767488+  83  Linux
/dev/sda2        19535101   625137344   302801122    5  Etendue
/dev/sda5        19535103   214853309    97659103+  83  Linux
/dev/sda6       214853373   223255304     4200966   82  Linux swap / Solaris
/dev/sda7       223255368   239625539     8185086   83  Linux
/dev/sda8       239625603   247802624     4088511   82  Linux swap / Solaris
/dev/sda9       247802688   625137344   188667328+  83  Linux
#

Clé non branchée :

# lsusb
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 002: ID 046d:c03f Logitech, Inc. UltraX Optical Mouse
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 007: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB
Bus 002 Device 003: ID 0bda:8189 Realtek Semiconductor Corp. RTL8187B Wireless 802.11g 54Mbps Network Adapter
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 5986:0370 Acer, Inc 
Bus 001 Device 002: ID 0bda:0158 Realtek Semiconductor Corp. USB 2.0 multicard reader
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
#

Clé branchée :

# lsusb
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 002: ID 046d:c03f Logitech, Inc. UltraX Optical Mouse
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 010: ID 090c:3000 Feiya Technology Corp. 
Bus 002 Device 007: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB
Bus 002 Device 003: ID 0bda:8189 Realtek Semiconductor Corp. RTL8187B Wireless 802.11g 54Mbps Network Adapter
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 5986:0370 Acer, Inc 
Bus 001 Device 002: ID 0bda:0158 Realtek Semiconductor Corp. USB 2.0 multicard reader
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
#

Elle apparaît donc ici en tant que "Feiya Technology Corp." (Bus 002 Device 010: ID 090c:3000)

Derniers messages après avoir débranché la clé : /!\ dans les messages les plus anciens, certains concernent un autre disque USB que j'ai testé juste avant

# dmesg | tail -n30
[ 1121.208579] sd 7:0:0:0: [sdc] Assuming drive cache: write through
[ 1121.211889] sd 7:0:0:0: [sdc] Test WP failed, assume Write Enabled
[ 1121.211897] sd 7:0:0:0: [sdc] Assuming drive cache: write through
[ 1121.211907]  sdc: sdc1
[ 1121.254990] sd 7:0:0:0: [sdc] Test WP failed, assume Write Enabled
[ 1121.254993] sd 7:0:0:0: [sdc] Assuming drive cache: write through
[ 1121.254995] sd 7:0:0:0: [sdc] Attached SCSI disk
[ 1220.369321] EXT4-fs (sdc1): warning: maximal mount count reached, running e2fsck is recommended
[ 1220.382370] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[ 1226.076235] EXT4-fs (sda1): warning: maximal mount count reached, running e2fsck is recommended
[ 1226.076627] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 1226.991204] EXT3-fs: barriers not enabled
[ 1227.009981] kjournald starting.  Commit interval 5 seconds
[ 1227.010011] EXT3-fs (sda5): warning: maximal mount count reached, running e2fsck is recommended
[ 1227.010295] EXT3-fs (sda5): using internal journal
[ 1227.010299] EXT3-fs (sda5): mounted filesystem with ordered data mode
[ 1236.840375] usb 2-2.3: new high speed USB device using ehci_hcd and address 9
[ 1236.957660] scsi8 : usb-storage 2-2.3:1.0
[ 1237.952299] scsi 8:0:0:0: Direct-Access              USB MEMORY BAR   1000 PQ: 0 ANSI: 0 CCS
[ 1237.953657] sd 8:0:0:0: Attached scsi generic sg4 type 0
[ 1237.960232] sd 8:0:0:0: [sdd] Attached SCSI removable disk
[ 1798.981597] WARNING! power/level is deprecated; use power/control instead
[ 1799.081189] usb 2-2.2: USB disconnect, address 8
[ 1938.046848] usb 2-2.3: USB disconnect, address 9
[ 2211.560389] usb 2-2.4: new high speed USB device using ehci_hcd and address 10
[ 2211.678313] scsi9 : usb-storage 2-2.4:1.0
[ 2212.672306] scsi 9:0:0:0: Direct-Access              USB MEMORY BAR   1000 PQ: 0 ANSI: 0 CCS
[ 2212.673646] sd 9:0:0:0: Attached scsi generic sg3 type 0
[ 2212.678740] sd 9:0:0:0: [sdc] Attached SCSI removable disk
[ 3887.484497] usb 2-2.4: USB disconnect, address 10
#

Et messages obtenus après rebranchement de la clé (uniquement ceux qui s'ajoutent par rapport à la commande précédente) :

# dmesg | tail -n30
.
.
.
[ 4111.460349] usb 2-2.2: new high speed USB device using ehci_hcd and address 11
[ 4111.578309] scsi10 : usb-storage 2-2.2:1.0
[ 4112.572393] scsi 10:0:0:0: Direct-Access              USB MEMORY BAR   1000 PQ: 0 ANSI: 0 CCS
[ 4112.573719] sd 10:0:0:0: Attached scsi generic sg3 type 0
[ 4112.578939] sd 10:0:0:0: [sdc] Attached SCSI removable disk
#

En résumé elle n'est montée nulle part et je ne vois aucun moyen d'y accéder par le système de fichiers.

D'ailleurs :

# fdisk sdb

Impossible d'ouvrir sdb
# fdisk sdc

Impossible d'ouvrir sdc

Tentative vaine du même genre :
(essayée à cause de cette ligne dans dmesg : [ 2212.678740] sd 9:0:0:0: [sdc] Attached SCSI removable disk)

# mount -t vfat /dev/sdc /media/essai_usb
mount : aucun media trouvé dans /dev/sdc
#

En revanche, mes disques externes usb et clés usb fonctionnent sans problème. Donc il y a un problème lié à cette clé. J'ai carte blanche pour tout détruire dessus, reformater, mais comment faire pour agir sur elle dans ces conditions ? Elle n'apparaît nulle part dans le système de fichiers... Toute aide sera bienvenue !

Merci, bonne journée,

Nicolas

Ubuntu-fr

Navigation

Liens de recherche

Annonce

#26 Le 09/03/2008, à 15:01

Re : clé USB non reconnue

#27 Le 09/03/2008, à 15:37

Re : clé USB non reconnue

#28 Le 09/03/2008, à 17:24

Re : clé USB non reconnue

#29 Le 09/03/2008, à 18:56

Re : clé USB non reconnue

#30 Le 09/03/2008, à 22:24

Re : clé USB non reconnue

#31 Le 10/03/2008, à 00:47

Re : clé USB non reconnue

#32 Le 10/03/2008, à 01:00

Re : clé USB non reconnue

#33 Le 10/03/2008, à 21:17

Re : clé USB non reconnue

#34 Le 10/03/2008, à 21:54

Re : clé USB non reconnue

#35 Le 11/04/2008, à 01:02

Re : clé USB non reconnue

#36 Le 11/04/2008, à 02:09

Re : clé USB non reconnue

#37 Le 11/04/2008, à 11:57

Re : clé USB non reconnue

#38 Le 19/02/2009, à 19:54

Re : clé USB non reconnue

#39 Le 20/02/2009, à 10:17

Re : clé USB non reconnue

#40 Le 23/02/2011, à 14:14

Re : clé USB non reconnue

Pied de page des forums