Pages : 1
#1 Le 25/11/2007, à 15:02
- Samourai22
Impossible de monter des périph USB
Bonjour à vous,
J'explique mon problème : je suis sous Xubuntu mais j'étais avant sous Ubuntu et le problème reste le même.
Toutes les clés USB, disques dur externes sont détectées lorsque je les branche mais message d'erreur : "Impossible de monter le volume"
Voici donc les détails de l'erreur :
mount: wrong fs type, bad option, bad superblock on /dev/sda1, missing codepage or helper program, or other error In some cases usefull info is found in syslog - try dmesg | tail or so
Je vous donne donc les résultats de la commande dmesg|tail :
tibo@tibo-desktop:~$ dmesg|tail
[ 111.600000] sda: Mode Sense: 23 00 00 00
[ 111.600000] sda: assuming drive cache: write through
[ 111.612000] SCSI device sda: 503808 512-byte hdwr sectors (258 MB)
[ 111.612000] sda: Write Protect is off
[ 111.612000] sda: Mode Sense: 23 00 00 00
[ 111.612000] sda: assuming drive cache: write through
[ 111.616000] sda: sda1
[ 111.620000] sd 0:0:0:0: Attached scsi removable disk sda
[ 111.644000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 112.744000] FAT: Unrecognized mount option "usefree" or missing valueEt plus largement les résultats pour juste dmesg :
tibo@tibo-desktop:~$ sudo dmesg
[ 0.000000] Linux version 2.6.20-16-generic (root@terranova) (gcc version 4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #2 SMP Sun Sep 23 19:50:39 UTC 2007 (Ubuntu 2.6.20-16.32-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] sanitize start
[ 0.000000] sanitize end
[ 0.000000] copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 000000000009fc00 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: 00000000000a0000 type: 2
[ 0.000000] copy_e820_map() start: 00000000000f0000 size: 0000000000010000 end: 0000000000100000 type: 2
[ 0.000000] copy_e820_map() start: 0000000000100000 size: 000000001fef0000 end: 000000001fff0000 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000001fff0000 size: 0000000000003000 end: 000000001fff3000 type: 4
[ 0.000000] copy_e820_map() start: 000000001fff3000 size: 000000000000d000 end: 0000000020000000 type: 3
[ 0.000000] copy_e820_map() start: 00000000ffff0000 size: 0000000000010000 end: 0000000100000000 type: 2
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
[ 0.000000] BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 511MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 131056) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 131056
[ 0.000000] HighMem 131056 -> 131056
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 131056
[ 0.000000] On node 0 totalpages: 131056
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 991 pages used for memmap
[ 0.000000] Normal zone: 125969 pages, LIFO batch:31
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] DMI 2.2 present.
[ 0.000000] ACPI: RSDP (v000 VIA694 ) @ 0x000f7310
[ 0.000000] ACPI: RSDT (v001 VIA694 MSI ACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000
[ 0.000000] ACPI: FADT (v001 VIA694 MSI ACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040
[ 0.000000] ACPI: DSDT (v001 VIA694 AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
[ 0.000000] ACPI: PM-Timer IO Port: 0x4008
[ 0.000000] Allocating PCI resources starting at 30000000 (gap: 20000000:dfff0000)
[ 0.000000] Detected 1302.368 MHz processor.
[ 15.279949] Built 1 zonelists. Total pages: 130033
[ 15.279957] Kernel command line: root=UUID=011b415c-263f-41ee-a265-088d87e52881 ro quiet splash
[ 15.280235] Local APIC disabled by BIOS -- you can enable it with "lapic"
[ 15.280258] mapped APIC to ffffd000 (0140a000)
[ 15.280265] Enabling fast FPU save and restore... done.
[ 15.280291] Initializing CPU#0
[ 15.280441] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 15.281999] Console: colour VGA+ 80x25
[ 15.283073] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 15.283721] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 15.318314] Memory: 508728k/524224k available (1993k kernel code, 14948k reserved, 900k data, 328k init, 0k highmem)
[ 15.318334] virtual kernel memory layout:
[ 15.318336] fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB)
[ 15.318338] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 15.318340] vmalloc : 0xe0800000 - 0xff7fe000 ( 495 MB)
[ 15.318342] lowmem : 0xc0000000 - 0xdfff0000 ( 511 MB)
[ 15.318344] .init : 0xc03d9000 - 0xc042b000 ( 328 kB)
[ 15.318347] .data : 0xc02f2429 - 0xc03d36d4 ( 900 kB)
[ 15.318349] .text : 0xc0100000 - 0xc02f2429 (1993 kB)
[ 15.318354] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 15.396410] Calibrating delay using timer specific routine.. 2607.26 BogoMIPS (lpj=5214530)
[ 15.396495] Security Framework v1.0.0 initialized
[ 15.396510] SELinux: Disabled at boot.
[ 15.396541] Mount-cache hash table entries: 512
[ 15.396834] CPU: After generic identify, caps: 0183f9ff c1c7f9ff 00000000 00000000 00000000 00000000 00000000
[ 15.396849] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 15.396854] CPU: L2 Cache: 256K (64 bytes/line)
[ 15.396859] CPU: After all inits, caps: 0183f9ff c1c7f9ff 00000000 00000420 00000000 00000000 00000000
[ 15.396878] Compat vDSO mapped to ffffe000.
[ 15.396890] Remapping vsyscall page to ffffe000
[ 15.396908] Checking 'hlt' instruction... OK.
[ 15.412469] SMP alternatives: switching to UP code
[ 15.412990] Freeing SMP alternatives: 11k freed
[ 15.413470] Early unpacking initramfs... done
[ 15.929634] ACPI: Core revision 20060707
[ 15.936802] ACPI: Looking for DSDT in initramfs... file /DSDT.aml not found, using machine DSDT.
[ 15.938364] ACPI: setting ELCR to 0200 (from 0e20)
[ 15.939888] CPU0: AMD Athlon(tm) processor stepping 04
[ 15.939899] SMP motherboard not detected.
[ 15.939905] Local APIC not detected. Using dummy APIC emulation.
[ 15.940012] Brought up 1 CPUs
[ 15.940605] Booting paravirtualized kernel on bare hardware
[ 15.940748] Time: 13:35:34 Date: 10/25/107
[ 15.940828] NET: Registered protocol family 16
[ 15.941044] EISA bus registered
[ 15.941052] ACPI: bus type pci registered
[ 15.973919] PCI: PCI BIOS revision 2.10 entry at 0xfb4f0, last bus=1
[ 15.973923] PCI: Using configuration type 1
[ 15.973927] Setting up standard PCI resources
[ 15.987730] ACPI: Interpreter enabled
[ 15.987738] ACPI: Using PIC for interrupt routing
[ 15.988686] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 15.988700] PCI: Probing PCI hardware (bus 00)
[ 15.988811] ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
[ 15.989071] Disabling VIA memory write queue (PCI ID 0305, rev 02): [55] 89 & 1f -> 09
[ 15.989326] PCI quirk: region 4000-40ff claimed by vt82c586 ACPI
[ 15.989333] PCI quirk: region 5000-500f claimed by vt82c686 SMB
[ 15.989540] Boot video device is 0000:01:00.0
[ 15.989589] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 16.008085] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
[ 16.008515] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 16.008943] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
[ 16.009368] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
[ 16.013099] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 16.013123] pnp: PnP ACPI init
[ 16.017592] pnp: PnP ACPI: found 13 devices
[ 16.017601] PnPBIOS: Disabled by ACPI PNP
[ 16.017739] PCI: Using ACPI for IRQ routing
[ 16.017746] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 16.041316] NET: Registered protocol family 8
[ 16.041320] NET: Registered protocol family 20
[ 16.042327] PCI: Bridge: 0000:00:01.0
[ 16.042330] IO window: disabled.
[ 16.042338] MEM window: dc000000-ddffffff
[ 16.042344] PREFETCH window: d0000000-d7ffffff
[ 16.042368] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 16.042428] NET: Registered protocol family 2
[ 16.080403] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 16.080605] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 16.081203] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 16.081516] TCP: Hash tables configured (established 16384 bind 8192)
[ 16.081522] TCP reno registered
[ 16.092453] checking if image is initramfs... it is
[ 17.051975] Freeing initrd memory: 6750k freed
[ 17.052954] audit: initializing netlink socket (disabled)
[ 17.052990] audit(1195997735.960:1): initialized
[ 17.053220] VFS: Disk quotas dquot_6.5.1
[ 17.053266] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 17.053380] io scheduler noop registered
[ 17.053385] io scheduler anticipatory registered
[ 17.053389] io scheduler deadline registered
[ 17.053401] io scheduler cfq registered (default)
[ 17.053429] PCI: Disabling Via external APIC routing
[ 17.053825] isapnp: Scanning for PnP cards...
[ 17.408169] isapnp: No Plug & Play device found
[ 17.451137] Real Time Clock Driver v1.12ac
[ 17.451234] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 17.451463] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 17.451724] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 17.452773] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 17.453255] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 17.453689] mice: PS/2 mouse device common for all mice
[ 17.454758] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 17.455322] input: Macintosh mouse button emulation as /class/input/input0
[ 17.455383] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 17.455391] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 17.455871] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 17.456349] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 17.456359] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 17.456594] EISA: Probing bus 0 at eisa.0
[ 17.456628] Cannot allocate resource for EISA slot 4
[ 17.456632] Cannot allocate resource for EISA slot 5
[ 17.456650] EISA: Detected 0 cards.
[ 17.487053] TCP cubic registered
[ 17.487069] NET: Registered protocol family 1
[ 17.487119] Using IPI No-Shortcut mode
[ 17.487316] ACPI: (supports S0 S1 S4 S5)
[ 17.487394] Magic number: 15:317:585
[ 17.487565] hash matches device ptyc3
[ 17.487732] Time: tsc clocksource has been installed.
[ 17.488729] Freeing unused kernel memory: 328k freed
[ 17.506306] input: AT Translated Set 2 keyboard as /class/input/input1
[ 18.868797] Capability LSM initialized
[ 18.940657] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 18.940670] ACPI: Processor [CPU0] (supports 2 throttling states)
[ 19.919192] VP_IDE: IDE controller at PCI slot 0000:00:07.1
[ 19.919231] VP_IDE: chipset revision 16
[ 19.919235] VP_IDE: not 100% native mode: will probe irqs later
[ 19.919256] VP_IDE: VIA vt82c686a (rev 22) IDE UDMA66 controller on pci0000:00:07.1
[ 19.919270] ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:DMA
[ 19.919293] ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:DMA
[ 19.919304] Probing IDE interface ide0...
[ 19.961278] usbcore: registered new interface driver usbfs
[ 19.961334] usbcore: registered new interface driver hub
[ 19.961382] usbcore: registered new device driver usb
[ 19.963237] USB Universal Host Controller Interface driver v3.0
[ 20.161818] Floppy drive(s): fd0 is 1.44M
[ 20.224931] FDC 0 is a post-1991 82077
[ 5.040000] Time: acpi_pm clocksource has been installed.
[ 5.072000] hda: ST340823A, ATA DISK drive
[ 5.352000] hdb: MAXTOR STM3802110A, ATA DISK drive
[ 5.408000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 5.408000] Probing IDE interface ide1...
[ 6.272000] hdc: SONY CD-RW CRX175A1, ATAPI CD/DVD-ROM drive
[ 7.056000] hdd: IDE DVD-ROM 16X, ATAPI CD/DVD-ROM drive
[ 7.112000] ide1 at 0x170-0x177,0x376 on irq 15
[ 7.124000] SCSI subsystem initialized
[ 7.136000] libata version 2.20 loaded.
[ 7.156000] hda: max request size: 128KiB
[ 7.188000] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
[ 7.188000] PCI: setting IRQ 10 as level-triggered
[ 7.188000] ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
[ 7.188000] uhci_hcd 0000:00:07.2: UHCI Host Controller
[ 7.188000] uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
[ 7.188000] uhci_hcd 0000:00:07.2: irq 10, io base 0x0000d400
[ 7.188000] usb usb1: configuration #1 chosen from 1 choice
[ 7.188000] hub 1-0:1.0: USB hub found
[ 7.188000] hub 1-0:1.0: 2 ports detected
[ 7.188000] hda: 78165360 sectors (40020 MB) w/1024KiB Cache, CHS=65535/16/63, UDMA(66)
[ 7.188000] hda: cache flushes not supported
[ 7.188000] hda: hda1 hda2 < hda5 >
[ 7.220000] hdb: max request size: 512KiB
[ 7.268000] hdb: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(66)
[ 7.292000] ACPI: PCI Interrupt 0000:00:07.3[D] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
[ 7.292000] uhci_hcd 0000:00:07.3: UHCI Host Controller
[ 7.292000] uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
[ 7.292000] uhci_hcd 0000:00:07.3: irq 10, io base 0x0000d800
[ 7.292000] usb usb2: configuration #1 chosen from 1 choice
[ 7.292000] hub 2-0:1.0: USB hub found
[ 7.292000] hub 2-0:1.0: 2 ports detected
[ 7.296000] hdb: cache flushes supported
[ 7.296000] hdb: hdb1 hdb2 hdb3
[ 7.360000] hdc: ATAPI 40X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
[ 7.360000] Uniform CD-ROM driver Revision: 3.20
[ 7.360000] hdd: ATAPI 44X DVD-ROM drive, 512kB Cache, UDMA(33)
[ 7.660000] usb 1-2: new full speed USB device using uhci_hcd and address 2
[ 7.824000] usb 1-2: configuration #1 chosen from 1 choice
[ 8.128000] Attempting manual resume
[ 8.128000] swsusp: Resume From Partition 3:67
[ 8.128000] PM: Checking swsusp image.
[ 8.136000] PM: Resume from disk failed.
[ 8.184000] EXT3-fs: INFO: recovery required on readonly filesystem.
[ 8.184000] EXT3-fs: write access will be enabled during recovery.
[ 11.500000] kjournald starting. Commit interval 5 seconds
[ 11.500000] EXT3-fs: hdb1: orphan cleanup on readonly fs
[ 11.500000] ext3_orphan_cleanup: deleting unreferenced inode 423489
[ 11.536000] ext3_orphan_cleanup: deleting unreferenced inode 618968
[ 11.548000] EXT3-fs: hdb1: 2 orphan inodes deleted
[ 11.548000] EXT3-fs: recovery complete.
[ 11.624000] EXT3-fs: mounted filesystem with ordered data mode.
[ 26.696000] via686a 0000:00:07.4: base address not set - upgrade BIOS or use force_addr=0xaddr
[ 27.336000] Linux agpgart interface v0.102 (c) Dave Jones
[ 27.384000] parport_pc: VIA 686A/8231 detected
[ 27.384000] parport_pc: probing current configuration
[ 27.384000] parport_pc: Current parallel port base: 0x378
[ 27.384000] parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
[ 27.400000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 27.424000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 27.480000] parport_pc: VIA parallel port: io=0x378, irq=7
[ 27.556000] agpgart: Detected VIA Twister-K/KT133x/KM133 chipset
[ 27.564000] agpgart: AGP aperture is 64M @ 0xd8000000
[ 27.572000] input: PC Speaker as /class/input/input2
[ 28.168000] eth0: register 'cdc_ether' at usb-0000:00:07.2-2, CDC Ethernet Device, 00:07:cb:00:00:ff
[ 28.168000] usbcore: registered new interface driver cdc_ether
[ 28.292000] input: ImExPS/2 Logitech Wheel Mouse as /class/input/input3
[ 28.680000] ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
[ 30.164000] lp0: using parport0 (interrupt-driven).
[ 30.256000] fuse init (API version 7.8)
[ 30.300000] NET: Registered protocol family 17
[ 30.412000] Adding 20482864k swap on /dev/hdb3. Priority:-1 extents:1 across:20482864k
[ 30.816000] EXT3 FS on hdb1, internal journal
[ 33.364000] input: Power Button (FF) as /class/input/input4
[ 33.364000] ACPI: Power Button (FF) [PWRF]
[ 33.396000] input: Power Button (CM) as /class/input/input5
[ 33.396000] ACPI: Power Button (CM) [PWRB]
[ 33.412000] input: Sleep Button (CM) as /class/input/input6
[ 33.412000] ACPI: Sleep Button (CM) [SLPB]
[ 33.612000] Using specific hotkey driver
[ 33.712000] NET: Registered protocol family 10
[ 33.712000] lo: Disabled Privacy Extensions
[ 33.760000] No dock devices found.
[ 33.872000] ibm_acpi: ec object not found
[ 34.140000] pcc_acpi: loading...
[ 34.616000] powernow: No powernow capabilities detected
[ 37.940000] ppdev: user-space parallel port driver
[ 39.300000] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[ 39.300000] apm: overridden by ACPI.
[ 40.900000] Capability LSM initialized
[ 41.164000] Bluetooth: Core ver 2.11
[ 41.164000] NET: Registered protocol family 31
[ 41.164000] Bluetooth: HCI device and connection manager initialized
[ 41.164000] Bluetooth: HCI socket layer initialized
[ 41.236000] Bluetooth: L2CAP ver 2.8
[ 41.236000] Bluetooth: L2CAP socket layer initialized
[ 41.292000] Bluetooth: RFCOMM socket layer initialized
[ 41.292000] Bluetooth: RFCOMM TTY layer initialized
[ 41.292000] Bluetooth: RFCOMM ver 1.8
[ 43.456000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 43.732000] Netfilter messages via NETLINK v0.30.
[ 43.748000] nf_conntrack version 0.5.0 (4095 buckets, 32760 max)
[ 44.000000] eth0: no IPv6 routers present
[ 105.992000] usb 2-1: new full speed USB device using uhci_hcd and address 2
[ 106.164000] usb 2-1: configuration #1 chosen from 1 choice
[ 106.340000] usbcore: registered new interface driver libusual
[ 106.360000] Initializing USB Mass Storage driver...
[ 106.360000] scsi0 : SCSI emulation for USB Mass Storage devices
[ 106.360000] usbcore: registered new interface driver usb-storage
[ 106.360000] USB Mass Storage support registered.
[ 106.360000] usb-storage: device found at 2
[ 106.360000] usb-storage: waiting for device to settle before scanning
[ 111.360000] usb-storage: device scan complete
[ 111.364000] scsi 0:0:0:0: Direct-Access USB DISK 28X PMAP PQ: 0 ANSI: 0 CCS
[ 111.596000] SCSI device sda: 503808 512-byte hdwr sectors (258 MB)
[ 111.600000] sda: Write Protect is off
[ 111.600000] sda: Mode Sense: 23 00 00 00
[ 111.600000] sda: assuming drive cache: write through
[ 111.612000] SCSI device sda: 503808 512-byte hdwr sectors (258 MB)
[ 111.612000] sda: Write Protect is off
[ 111.612000] sda: Mode Sense: 23 00 00 00
[ 111.612000] sda: assuming drive cache: write through
[ 111.616000] sda: sda1
[ 111.620000] sd 0:0:0:0: Attached scsi removable disk sda
[ 111.644000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 112.744000] FAT: Unrecognized mount option "usefree" or missing valueJe précise que mon ordi est à jour d'aujourd'hui même.
Si quelqu'un pouvait me dire d'où vient mon problème, ça m'arrangerait.
J'ai essayé de monter le volume manuellement, mais alors impossible d'écrire dessus...
Si je comprends bien la dernière ligne de code, c'est que le FAT n'est pas reconnu ... Mais je ne comprends pas pourquoi ...
I need somebody help !
Merci d'avance,
Hors ligne
#2 Le 25/11/2007, à 17:17
- Samourai22
Re : Impossible de monter des périph USB
J'ai pourtant corrigé le fichier /etc/init.d/mountdevsubfs.sh comme dit dans un autre post [résolu], donc le problème ne vient pas de là ...
J'ai également installé, a partir de synpatic, ce qui pouvait être en lien avec les partitions NTFS, ou FAT (car les périphériques que j'ai branché sont tous en FAT (16 et 32) et NTFS ...
Mais étant donné que mon disque dur interne windows est détecté, et libre de lecture et d'écriture, je ne pense pas que ça vienne du format.
Hors ligne
Pages : 1