#1 Le 27/09/2016, à 21:06
- tarkan99
analyse smartctl d'un disque Error: UNC at LBA
Bonsoir,
j'ai vu dans un log des erreurs sur mon disque sdb.
il s'agit d'un 2° disque de 160go ne contenant que des données non vitales.
Je ne suis pas encore expert au point d'interpréter une analyse smartctl.
Risque-t-il de lâcher rapidement ou non, au vu du rapport suivant :
Un grand merci à ceux qui me guideront !
smartctl 6.5 2016-01-24 r4214 [i686-linux-4.4.0-38-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Maxtor DiamondMax 21
Device Model: MAXTOR STM3160215AS
Serial Number: 6RA5F63J
Firmware Version: 3.AAD
User Capacity: 160 041 885 696 bytes [160 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-7 (minor revision not indicated)
Local Time is: Tue Sep 27 21:56:02 2016 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 54) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 118 099 006 Pre-fail Always - 169665044
3 Spin_Up_Time 0x0003 097 097 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 098 098 020 Old_age Always - 2722
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 090 060 030 Pre-fail Always - 948199842
9 Power_On_Hours 0x0032 072 072 000 Old_age Always - 25217
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 098 098 020 Old_age Always - 2712
187 Reported_Uncorrect 0x0032 099 099 000 Old_age Always - 1
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 060 050 045 Old_age Always - 40 (Min/Max 24/41)
194 Temperature_Celsius 0x0022 040 050 000 Old_age Always - 40 (0 15 0 0 0)
195 Hardware_ECC_Recovered 0x001a 076 072 000 Old_age Always - 188458683
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 1
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 Data_Address_Mark_Errs 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 2
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 2 occurred at disk power-on lifetime: 8347 hours (347 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 e2 4d 75 e0 Error: UNC at LBA = 0x00754de2 = 7687650
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 40 cf 4d 75 e0 00 00:01:25.695 READ DMA EXT
25 00 40 8f 4d 75 e0 00 00:01:25.695 READ DMA EXT
25 00 40 4f 4d 75 e0 00 00:01:25.694 READ DMA EXT
25 00 40 0f 4d 75 e0 00 00:01:25.683 READ DMA EXT
25 00 40 cf 4c 75 e0 00 00:01:25.683 READ DMA EXT
Error 1 occurred at disk power-on lifetime: 6407 hours (266 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 46 40 ff e0 Error: ICRC, ABRT at LBA = 0x00ff4046 = 16728134
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 03 08 3f 40 ff e0 00 00:20:27.652 READ DMA EXT
25 03 08 2f 5f 60 e0 00 00:20:27.623 READ DMA EXT
25 03 08 27 5f 60 e0 00 00:20:27.617 READ DMA EXT
25 03 08 3f 6b 60 e0 00 00:20:27.607 READ DMA EXT
25 03 08 37 6b 60 e0 00 00:20:27.604 READ DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 25217 -
# 2 Short offline Completed without error 00% 25166 -
# 3 Extended offline Completed without error 00% 24822 -
# 4 Extended offline Interrupted (host reset) 90% 24822 -
# 5 Short offline Completed without error 00% 24821 -
# 6 Extended offline Interrupted (host reset) 80% 24821 -
# 7 Short offline Aborted by host 60% 24548 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.Pour le disque système de la machine :
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.10
Device Model: ST3320820AS
Serial Number: 5QF1EQAE
Firmware Version: 3.AAD
User Capacity: 320 072 933 376 bytes [320 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-7 (minor revision not indicated)
Local Time is: Tue Sep 27 22:02:38 2016 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 115) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 108 093 006 Pre-fail Always - 137039226
3 Spin_Up_Time 0x0003 090 090 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 095 095 020 Old_age Always - 5406
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 084 060 030 Pre-fail Always - 287565531
9 Power_On_Hours 0x0032 090 090 000 Old_age Always - 9336
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 095 095 020 Old_age Always - 5492
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 055 050 045 Old_age Always - 45 (Min/Max 24/46)
194 Temperature_Celsius 0x0022 045 050 000 Old_age Always - 45 (0 14 0 0 0)
195 Hardware_ECC_Recovered 0x001a 066 058 000 Old_age Always - 193675064
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 Data_Address_Mark_Errs 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 9336 -
# 2 Extended offline Aborted by host 90% 9303 -
# 3 Extended offline Aborted by host 90% 9303 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.xubuntu 22.04.1 sur machine assemblée base de Core i5 9400
Hors ligne
#2 Le 27/09/2016, à 23:23
- Bougron
Re : analyse smartctl d'un disque Error: UNC at LBA
Bonsoir
Te dire quand le disque de 160 go va lâcher ce n'est pas facile. La mécanique est simplement usée (par l'âge) et va mettre de plus en plus de temps à faire les commandes que tu demandes.
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 118 099 006 Pre-fail Always - 169665044
7 Seek_Error_Rate 0x000f 090 060 030 Pre-fail Always - 948199842
9 Power_On_Hours 0x0032 072 072 000 Old_age Always - 25217
195 Hardware_ECC_Recovered 0x001a 076 072 000 Old_age Always - 188458683Mais c'est aussi pareil pour le disque de 320 Go
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 108 093 006 Pre-fail Always - 137039226
7 Seek_Error_Rate 0x000f 084 060 030 Pre-fail Always - 287565531
9 Power_On_Hours 0x0032 090 090 000 Old_age Always - 9336
195 Hardware_ECC_Recovered 0x001a 066 058 000 Old_age Always - 193675064On peut voir dans certains rapports des valeurs en millions de milliards.
Suis l'évolution chaque quinzaine.
Dernière modification par Bougron (Le 27/09/2016, à 23:25)
Hors ligne
#3 Le 28/09/2016, à 06:28
- tarkan99
Re : analyse smartctl d'un disque Error: UNC at LBA
ok merci !
je vais les user jusqu'à la corde et ensuite ce sera l'occasion de remplacer le P Bell par un truc un peu plus récent.
xubuntu 22.04.1 sur machine assemblée base de Core i5 9400
Hors ligne