Contenu | Rechercher | Menus

Annonce

Si vous avez des soucis pour rester connecté, déconnectez-vous puis reconnectez-vous depuis ce lien en cochant la case
Me connecter automatiquement lors de mes prochaines visites.

À propos de l'équipe du forum.

#1 Le 23/08/2017, à 12:28

Sweery

[Résolu] : MSI GS60 6QC 231XFR -- Ubuntu 16.04 -- Bluetooth inexistant

Bonjour à tous,

J'ai récemment fait l’acquisition d'un PC portable MSI GS60 6QC 231XFR sans OS avec FreeDos.

Caractéristiques :
Processeur : Intel Core i7 (6ème génération) 6700HQ - 2.6 GHz
RAM : 8 Go DDR4 SDRAM
Carte Graphique : NVIDIA GeForce GTX 960M - 2 Go GDDR5 SDRAM
Carte Wifi/Bluetooth : Qualcomm Atheros QCA6174

------------------------------------------------------------------------------------------------------------------------------------------
L'installation de Ubuntu 16.04 a été un succès. Seulement voila la carte wifi est bien détectée et fonctionnelle mais le Bluetooth n'est pas détecté bien que le voyant Bluetooth soit allumé en permanence.
----------------------------------------------------------------------------------------------------------------------------------------------------
D’après la commande suivante voici la version utilisée :

sweet@sweet-GS60-6QC:~$ ethtool -i wlp2s0
driver: ath10k_pci
version: 4.10.0-32-generic
firmware-version: SW_RM.1.1.1-00157-QCARMSWPZ-1
expansion-rom-version: 
bus-info: 0000:02:00.0
supports-statistics: yes
supports-test: no
supports-eeprom-access: no
supports-register-dump: no
supports-priv-flags: no

-------------------------------------------------------------------------------------------------------------------------
Quand je vais dans le dossier : /lib/firmware/ath10k/QCA6174  je vois deux dossiers de firmware.

sweet@sweet-GS60-6QC:/lib/firmware/ath10k/QCA6174$ ls
hw2.1  hw3.0

--------------------------------------------------------------------------------------------------------------------
Après avoir fait une sauvegarde je les ai supprimés un par un pour voir lequel était utilisé puis j'ai tout remis comme au départ et il se trouve que la carte utilise le firmware du dossier hw2.1 , est ce normal ?

J'ai lu sur d'autres site que la cause de l'absence du bluetooth était peut être dû à un firmware obsolète.

----------------------------------------------------------------------------------------------------------------------------------------------------
Voici mes questions :
1-Est ce que je possède la dernière version pour cette carte?
2-Est ce que la carte doit utiliser le firmware du dossier hw3.0 ? si oui comment lui dire?
3-cela n'est pas pris en charge actuellement

Je m'en remet à vous car je m'arrache les cheveux, merci d'avance smile
pour toute info complémentaire, je suis là

Dernière modification par Sweery (Le 26/08/2017, à 13:27)

Hors ligne

#2 Le 23/08/2017, à 18:23

Sweery

Re : [Résolu] : MSI GS60 6QC 231XFR -- Ubuntu 16.04 -- Bluetooth inexistant

up , je ne demande pas forcement de solution exacte.

postez vos idées (pertinentes) et je n'aurai aucune hésitation à modifier jusqu'au noyau du système smile

Dernière modification par Sweery (Le 24/08/2017, à 17:33)

Hors ligne

#3 Le 23/08/2017, à 18:43

xubu1957

Re : [Résolu] : MSI GS60 6QC 231XFR -- Ubuntu 16.04 -- Bluetooth inexistant

Bonjour,

Fournis,  en te servant du Retour utilisable de commande :

uname -a; lspci -nnk | grep -iA2 net; lsusb; dmesg | grep -i bluetooth; dmesg | grep -i firmware; lsmod | grep bluetooth

Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Résolu] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci.                   Membre de Linux-Azur

Hors ligne

#4 Le 23/08/2017, à 18:52

Sweery

Re : [Résolu] : MSI GS60 6QC 231XFR -- Ubuntu 16.04 -- Bluetooth inexistant

Bonsoir xubu1957 voici le résultat :

root@sweet-GS60-6QC:~# uname -a; lspci -nnk | grep -iA2 net; lsusb; dmesg | grep -i bluetooth; dmesg | grep -i firmware; lsmod | grep bluetooth
Linux sweet-GS60-6QC 4.10.0-32-generic #36~16.04.1-Ubuntu SMP Wed Aug 9 09:19:02 UTC 2017 x86_64 x86_64 x86_64 GNU/Linux
02:00.0 Network controller [0280]: Qualcomm Atheros QCA6174 802.11ac Wireless Network Adapter [168c:003e] (rev 20)
	Subsystem: Bigfoot Networks, Inc. Killer N1525 Wireless-AC [1a56:1525]
	Kernel driver in use: ath10k_pci
	Kernel modules: ath10k_pci
--
04:00.0 Ethernet controller [0200]: Qualcomm Atheros Killer E2400 Gigabit Ethernet Controller [1969:e0a1] (rev 10)
	Subsystem: Micro-Star International Co., Ltd. [MSI] Killer E2400 Gigabit Ethernet Controller [1462:116b]
	Kernel driver in use: alx
	Kernel modules: alx
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 002: ID 1770:ff00  
Bus 001 Device 004: ID 12c9:1001  
Bus 001 Device 003: ID 0cf3:3004 Atheros Communications, Inc. AR3012 Bluetooth 4.0
Bus 001 Device 005: ID 1c4f:0024 SiGma Micro 
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
[    2.275507] Bluetooth: Core ver 2.22
[    2.275519] Bluetooth: HCI device and connection manager initialized
[    2.275521] Bluetooth: HCI socket layer initialized
[    2.275523] Bluetooth: L2CAP socket layer initialized
[    2.275527] Bluetooth: SCO socket layer initialized
[    2.282031] Bluetooth: HCI UART driver ver 2.3
[    2.282033] Bluetooth: HCI UART protocol H4 registered
[    2.282033] Bluetooth: HCI UART protocol BCSP registered
[    2.282034] Bluetooth: HCI UART protocol LL registered
[    2.282035] Bluetooth: HCI UART protocol ATH3K registered
[    2.282035] Bluetooth: HCI UART protocol Three-wire (H5) registered
[    2.284488] Bluetooth: HCI UART protocol Intel registered
[    2.284515] Bluetooth: HCI UART protocol Broadcom registered
[    2.284515] Bluetooth: HCI UART protocol QCA registered
[    2.284516] Bluetooth: HCI UART protocol AG6XX registered
[    2.284517] Bluetooth: HCI UART protocol Marvell registered
[    2.360468] Bluetooth: Patch file not found ar3k/AthrBT_0x00000200.dfu
[    2.360470] Bluetooth: Loading patch file failed
[   14.387983] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   14.387985] Bluetooth: BNEP filters: protocol multicast
[   14.387988] Bluetooth: BNEP socket layer initialized
[    0.177108] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
[    1.142861] [drm] GuC firmware load skipped
[    1.631986] psmouse serio1: elantech: assuming hardware version 4 (with firmware version 0x361f00)
[    2.360466] usb 1-10: Direct firmware load for ar3k/AthrBT_0x00000200.dfu failed with error -2
[    2.630608] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:02:00.0.bin failed with error -2
[    2.630615] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/cal-pci-0000:02:00.0.bin failed with error -2
[    2.631895] ath10k_pci 0000:02:00.0: firmware ver SW_RM.1.1.1-00157-QCARMSWPZ-1 api 5 features ignore-otp,no-4addr-pad crc32 10bf8e08
bluetooth             557056  14 btrtl,hci_uart,btintel,btqca,bnep,btbcm,ath3k,btusb

Dernière modification par Sweery (Le 23/08/2017, à 19:20)

Hors ligne

#5 Le 23/08/2017, à 18:58

xubu1957

Re : [Résolu] : MSI GS60 6QC 231XFR -- Ubuntu 16.04 -- Bluetooth inexistant

Pour ajouter toi-même les balises code à tes précédents messages

  • Cliquer sur  le lien « Modifier » en bas à droite du message

  • Sélectionner le texte

  • Cliquer sur le <> de l'éditeur de message

1485703524.png


Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Résolu] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci.                   Membre de Linux-Azur

Hors ligne

#6 Le 23/08/2017, à 19:03

xubu1957

Re : [Résolu] : MSI GS60 6QC 231XFR -- Ubuntu 16.04 -- Bluetooth inexistant

Direct firmware load for ar3k/AthrBT_0x00000200.dfu failed with error -2

Un bug signalé > ubuntu-bugs@lists.ubuntu.com/msg5102891.html


Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Résolu] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci.                   Membre de Linux-Azur

Hors ligne

#7 Le 23/08/2017, à 19:08

Sweery

Re : [Résolu] : MSI GS60 6QC 231XFR -- Ubuntu 16.04 -- Bluetooth inexistant

oot@sweet-GS60-6QC:~# uname -a; lspci -nnk | grep -iA2 net; lsusb; dmesg | grep -i bluetooth; dmesg | grep -i firmware; lsmod | grep bluetooth
Linux sweet-GS60-6QC 4.10.0-32-generic #36~16.04.1-Ubuntu SMP Wed Aug 9 09:19:02 UTC 2017 x86_64 x86_64 x86_64 GNU/Linux
02:00.0 Network controller [0280]: Qualcomm Atheros QCA6174 802.11ac Wireless Network Adapter [168c:003e] (rev 20)
    Subsystem: Bigfoot Networks, Inc. Killer N1525 Wireless-AC [1a56:1525]
    Kernel driver in use: ath10k_pci
    Kernel modules: ath10k_pci
--
04:00.0 Ethernet controller [0200]: Qualcomm Atheros Killer E2400 Gigabit Ethernet Controller [1969:e0a1] (rev 10)
    Subsystem: Micro-Star International Co., Ltd. [MSI] Killer E2400 Gigabit Ethernet Controller [1462:116b]
    Kernel driver in use: alx
    Kernel modules: alx
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 002: ID 1770:ff00 
Bus 001 Device 004: ID 12c9:1001 
Bus 001 Device 003: ID 0cf3:3004 Atheros Communications, Inc. AR3012 Bluetooth 4.0
Bus 001 Device 005: ID 1c4f:0024 SiGma Micro
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
[    2.275507] Bluetooth: Core ver 2.22
[    2.275519] Bluetooth: HCI device and connection manager initialized
[    2.275521] Bluetooth: HCI socket layer initialized
[    2.275523] Bluetooth: L2CAP socket layer initialized
[    2.275527] Bluetooth: SCO socket layer initialized
[    2.282031] Bluetooth: HCI UART driver ver 2.3
[    2.282033] Bluetooth: HCI UART protocol H4 registered
[    2.282033] Bluetooth: HCI UART protocol BCSP registered
[    2.282034] Bluetooth: HCI UART protocol LL registered
[    2.282035] Bluetooth: HCI UART protocol ATH3K registered
[    2.282035] Bluetooth: HCI UART protocol Three-wire (H5) registered
[    2.284488] Bluetooth: HCI UART protocol Intel registered
[    2.284515] Bluetooth: HCI UART protocol Broadcom registered
[    2.284515] Bluetooth: HCI UART protocol QCA registered
[    2.284516] Bluetooth: HCI UART protocol AG6XX registered
[    2.284517] Bluetooth: HCI UART protocol Marvell registered
[    2.360468] Bluetooth: Patch file not found ar3k/AthrBT_0x00000200.dfu
[    2.360470] Bluetooth: Loading patch file failed
[   14.387983] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   14.387985] Bluetooth: BNEP filters: protocol multicast
[   14.387988] Bluetooth: BNEP socket layer initialized
[    0.177108] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
[    1.142861] [drm] GuC firmware load skipped
[    1.631986] psmouse serio1: elantech: assuming hardware version 4 (with firmware version 0x361f00)
[    2.360466] usb 1-10: Direct firmware load for ar3k/AthrBT_0x00000200.dfu failed with error -2
[    2.630608] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:02:00.0.bin failed with error -2
[    2.630615] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/cal-pci-0000:02:00.0.bin failed with error -2
[    2.631895] ath10k_pci 0000:02:00.0: firmware ver SW_RM.1.1.1-00157-QCARMSWPZ-1 api 5 features ignore-otp,no-4addr-pad crc32 10bf8e08
bluetooth             557056  14 btrtl,hci_uart,btintel,btqca,bnep,btbcm,ath3k,btusb

Hors ligne

#8 Le 23/08/2017, à 19:11

Sweery

Re : [Résolu] : MSI GS60 6QC 231XFR -- Ubuntu 16.04 -- Bluetooth inexistant

merci pour ta réponse donc il y a une erreur alors ?

[    2.360466] usb 1-10: Direct firmware load for ar3k/AthrBT_0x00000200.dfu failed with error -2
[    2.630608] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:02:00.0.bin failed with error -2
[    2.630615] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/cal-pci-0000:02:00.0.bin failed with error -2

?

Dernière modification par Sweery (Le 23/08/2017, à 19:12)

Hors ligne

#9 Le 23/08/2017, à 19:23

xubu1957

Re : [Résolu] : MSI GS60 6QC 231XFR -- Ubuntu 16.04 -- Bluetooth inexistant

J'ai vu que le développeur cité dans le lien du bug est Pilot6 > launchpad.net/~hanipouspilot

Il travaille beaucoup en Wifi > ubuntu/rtlwifi/+packages


Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Résolu] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci.                   Membre de Linux-Azur

Hors ligne

#10 Le 23/08/2017, à 19:33

Sweery

Re : [Résolu] : MSI GS60 6QC 231XFR -- Ubuntu 16.04 -- Bluetooth inexistant

mais cela me mène vers des pages à lien multiples,  et je vois trusty c'est la version 14.04 de ubuntu  est ce que je dois toutes les testées ? yikes

Dernière modification par Sweery (Le 23/08/2017, à 19:34)

Hors ligne

#11 Le 23/08/2017, à 19:35

xubu1957

Re : [Résolu] : MSI GS60 6QC 231XFR -- Ubuntu 16.04 -- Bluetooth inexistant

Il fallait regarder dans le premier lien > assignedbugs

l'autre était pour montrer l'activité de Pilot6.


Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Résolu] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci.                   Membre de Linux-Azur

Hors ligne

#12 Le 23/08/2017, à 20:10

xubu1957

Re : [Résolu] : MSI GS60 6QC 231XFR -- Ubuntu 16.04 -- Bluetooth inexistant

Tu peux fournir :

sudo service bluetooth status

?


Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Résolu] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci.                   Membre de Linux-Azur

Hors ligne

#13 Le 23/08/2017, à 20:17

Sweery

Re : [Résolu] : MSI GS60 6QC 231XFR -- Ubuntu 16.04 -- Bluetooth inexistant

C'est incroyable il est actif :

root@sweet-GS60-6QC:~# service bluetooth status
● bluetooth.service - Bluetooth service
   Loaded: loaded (/lib/systemd/system/bluetooth.service; enabled; vendor preset
   Active: active (running) since mer. 2017-08-23 19:45:51 CEST; 1h 26min ago
     Docs: man:bluetoothd(8)
 Main PID: 1240 (bluetoothd)
   Status: "Running"
   CGroup: /system.slice/bluetooth.service
           └─1240 /usr/lib/bluetooth/bluetoothd

août 23 19:45:51 sweet-GS60-6QC systemd[1]: Starting Bluetooth service...
août 23 19:45:51 sweet-GS60-6QC bluetoothd[1240]: Bluetooth daemon 5.37
août 23 19:45:51 sweet-GS60-6QC systemd[1]: Started Bluetooth service.
août 23 19:45:51 sweet-GS60-6QC bluetoothd[1240]: Starting SDP server
août 23 19:45:51 sweet-GS60-6QC bluetoothd[1240]: Bluetooth management interface

mais non détecté en tant que périphérique  sur le pc, ni avec mon Téléphone je le vois pas, mais le voyant Bluetooth est allumé sur le PC en permanence.
ça me rend fou lol

Dernière modification par Sweery (Le 23/08/2017, à 20:25)

Hors ligne

#14 Le 23/08/2017, à 20:30

xubu1957

Re : [Résolu] : MSI GS60 6QC 231XFR -- Ubuntu 16.04 -- Bluetooth inexistant

Je donne ces pistes :

As tu installé : pavucontrol ?

Le 19/04/2016, doug2109 a écrit :

Pour récapituler le problème et la solution :

Problème : L'association avec un périphérique audio Bluetooth fonctionne et est possible (marqué "connecté" dans Paramètres > Bluetooth). Cependant, ce dernier n'est pas affiché dans la liste des périphériques de sortie dans Paramètres > Son, ce qui rend donc la lecture de son sur celui-ci impossible.
Solution : Installer le paquet pavucontrol et lancer pavucontrol. Dans l'onglet périphérique de sortie, le périphérique Bluetooth en question apparaît alors et il est possible de cocher ou cliquer sur le bouton Définir comme alternative. Il apparaîtra aussi désormais dans Paramètres > Son.

Cordialement et au plaisir,

(edit)

Le 06/06/2017, pingouin libre a écrit :

Petit up pour ceux qui veulent installer le paquet pavucontrol, il est possible que votre casque bluetooth ne soit pas visible dans les périphériques de sortie -> votre périphérique est sûrement éteint !
Aller dans l'onglet Configuration de pavucontrol et si vous voyez votre périphérique, passez le du mode éteint au mode A2DP et miracle... du son arrive smile


> [Résolu] Sortie son sur périphérique audio bluetooth et aussi :

Le 29/10/2016, seebz a écrit :

Pour corriger les messages Protocol not available, il faut installer pulseaudio-module-bluetooth.

sudo apt-get install pulseaudio-module-bluetooth
Le 19/09/2015, Berz1gue a écrit :

Bonjour,

J'ai enfin réussi à faire fonctionner mon enceinte bluetooth sur mon portable après avoir installé via la logithèque "pavucontrol".
Puis aller dans paramètres - son- sélectionner un périphérique pour la sortie - mon enceinte bluetooth.*
Aller dans profil et mettre lecture haute fidélité (H2PD).

> [resolu] Problème de connexion à haut parleur bluetooth

Le 29/07/2017, Naziel a écrit :

Bonjour,

Après avoir lancé une vidéo sur youtube par exemple (il est important que ce soit en lecture, n'importe quelle application qui envoie du son ira) et connecté ton enceinte bluetooth, peux tu regarder dans paramètres sonores/contrôle de volume, dans l'onglet lecture, tu devrais avoir le choix de rediriger le son de ton navigateur internet vers tes enceintes pc et celle en bluetooth.
Cdt.

Dernière modification par xubu1957 (Le 14/11/2017, à 15:22)


Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Résolu] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci.                   Membre de Linux-Azur

Hors ligne

#15 Le 23/08/2017, à 21:04

xubu1957

Re : [Résolu] : MSI GS60 6QC 231XFR -- Ubuntu 16.04 -- Bluetooth inexistant

Pour info pour une autre Qualcom et pilote ath9k

> [RESOLU] Connexion xubuntu 16.04 avec enceinte JBL (bluetooth)


Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Résolu] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci.                   Membre de Linux-Azur

Hors ligne

#16 Le 23/08/2017, à 21:19

Sweery

Re : [Résolu] : MSI GS60 6QC 231XFR -- Ubuntu 16.04 -- Bluetooth inexistant

je dois partir maintenant, merci pour tes réponses , j'y répondrai demain (je vais pas dormir de la nuit)   le Bluetooth doit marché !!!!  yikes

Dernière modification par Sweery (Le 23/08/2017, à 21:21)

Hors ligne

#17 Le 23/08/2017, à 21:21

xubu1957

Re : [Résolu] : MSI GS60 6QC 231XFR -- Ubuntu 16.04 -- Bluetooth inexistant

Bonne nuit quand même. wink


Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Résolu] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci.                   Membre de Linux-Azur

Hors ligne

#18 Le 23/08/2017, à 21:27

ylag

Re : [Résolu] : MSI GS60 6QC 231XFR -- Ubuntu 16.04 -- Bluetooth inexistant

Salut,

Sweery a écrit :

la totalité de ces drivers sont destinés aux périphériques bluetooth externes et Ubuntu 16.04 possède déjà les fichiers . je me rend à l'évidence , mon matériel est trop récent (2017)

Peut-être une piste par là : https://github.com/kvalo/ath10k-firmware

?

Hors ligne

#19 Le 24/08/2017, à 10:47

Sweery

Re : [Résolu] : MSI GS60 6QC 231XFR -- Ubuntu 16.04 -- Bluetooth inexistant

Bonjour alors voici un petit récapitulatif des différentes solutions testées ainsi que le résultat:

1 - Installation de Pavucontrol ==>  Détecte seulement les hauts-parleurs

2 - Vérification de la présence de pulseaudio-module-bluetooth ==> module présent

3 - Installation de Blueman et mise à jour de celui-ci via le dépôt ppa:blueman/ppa ==> Apparition de l’icône Bluetooth jusque là absent, en haut à droite de la barre système (Mais message d'erreur "Aucun adaptateur n'a  été trouvé" lorsqu'on clique sur configurer un nouvel appareil

4 - Vérification de la présence des lignes suivantes dans le fichier /etc/pulse/default.pa

.ifexists module-bluetooth-discover.so
load-module module-bluetooth-discover
.endif

Fichier /etc/pulse/default.pa

#!/usr/bin/pulseaudio -nF
#
# This file is part of PulseAudio.
#
# PulseAudio is free software; you can redistribute it and/or modify it
# under the terms of the GNU Lesser General Public License as published by
# the Free Software Foundation; either version 2 of the License, or
# (at your option) any later version.
#
# PulseAudio is distributed in the hope that it will be useful, but
# WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
# General Public License for more details.
#
# You should have received a copy of the GNU Lesser General Public License
# along with PulseAudio; if not, see <http://www.gnu.org/licenses/>.

# This startup script is used only if PulseAudio is started per-user
# (i.e. not in system mode)

.nofail

### Load something into the sample cache
#load-sample-lazy x11-bell /usr/share/sounds/freedesktop/stereo/bell.oga
#load-sample-lazy pulse-hotplug /usr/share/sounds/freedesktop/stereo/device-added.oga
#load-sample-lazy pulse-coldplug /usr/share/sounds/freedesktop/stereo/device-added.oga
#load-sample-lazy pulse-access /usr/share/sounds/freedesktop/stereo/message.oga

.fail

### Automatically restore the volume of streams and devices
load-module module-device-restore
load-module module-stream-restore
load-module module-card-restore

### Automatically augment property information from .desktop files
### stored in /usr/share/application
load-module module-augment-properties

### Should be after module-*-restore but before module-*-detect
load-module module-switch-on-port-available

### Load audio drivers statically
### (it's probably better to not load these drivers manually, but instead
### use module-udev-detect -- see below -- for doing this automatically)
#load-module module-alsa-sink
#load-module module-alsa-source device=hw:1,0
#load-module module-oss device="/dev/dsp" sink_name=output source_name=input
#load-module module-oss-mmap device="/dev/dsp" sink_name=output source_name=input
#load-module module-null-sink
#load-module module-pipe-sink

### Automatically load driver modules depending on the hardware available
.ifexists module-udev-detect.so
load-module module-udev-detect
.else
### Use the static hardware detection module (for systems that lack udev support)
load-module module-detect
.endif

### Automatically connect sink and source if JACK server is present
.ifexists module-jackdbus-detect.so
.nofail
load-module module-jackdbus-detect channels=2
.fail
.endif

### Automatically load driver modules for Bluetooth hardware
.ifexists module-bluetooth-policy.so
load-module module-bluetooth-policy
.endif

.ifexists module-bluetooth-discover.so
load-module module-bluetooth-discover
.endif

### Load several protocols
.ifexists module-esound-protocol-unix.so
load-module module-esound-protocol-unix
.endif
load-module module-native-protocol-unix

### Network access (may be configured with paprefs, so leave this commented
### here if you plan to use paprefs)
#load-module module-esound-protocol-tcp
#load-module module-native-protocol-tcp
#load-module module-zeroconf-publish

### Load the RTP receiver module (also configured via paprefs, see above)
#load-module module-rtp-recv

### Load the RTP sender module (also configured via paprefs, see above)
#load-module module-null-sink sink_name=rtp format=s16be channels=2 rate=44100 sink_properties="device.description='RTP Multicast Sink'"
#load-module module-rtp-send source=rtp.monitor

### Load additional modules from GConf settings. This can be configured with the paprefs tool.
### Please keep in mind that the modules configured by paprefs might conflict with manually
### loaded modules.
.ifexists module-gconf.so
.nofail
load-module module-gconf
.fail
.endif

### Automatically restore the default sink/source when changed by the user
### during runtime
### NOTE: This should be loaded as early as possible so that subsequent modules
### that look up the default sink/source get the right value
load-module module-default-device-restore

### Automatically move streams to the default sink if the sink they are
### connected to dies, similar for sources
load-module module-rescue-streams

### Make sure we always have a sink around, even if it is a null sink.
load-module module-always-sink

### Honour intended role device property
load-module module-intended-roles

### Automatically suspend sinks/sources that become idle for too long
load-module module-suspend-on-idle

### If autoexit on idle is enabled we want to make sure we only quit
### when no local session needs us anymore.
.ifexists module-console-kit.so
load-module module-console-kit
.endif
.ifexists module-systemd-login.so
load-module module-systemd-login
.endif

### Enable positioned event sounds
load-module module-position-event-sounds

### Cork music/video streams when a phone stream is active
#load-module module-role-cork

### Modules to allow autoloading of filters (such as echo cancellation)
### on demand. module-filter-heuristics tries to determine what filters
### make sense, and module-filter-apply does the heavy-lifting of
### loading modules and rerouting streams.
load-module module-filter-heuristics
load-module module-filter-apply

# X11 modules should not be started from default.pa so that one daemon
# can be shared by multiple sessions.

### Load X11 bell module
#load-module module-x11-bell sample=x11-bell

### Register ourselves in the X11 session manager
#load-module module-x11-xsmp

### Publish connection data in the X11 root window
#.ifexists module-x11-publish.so
#.nofail
#load-module module-x11-publish
#.fail
#.endif

### Make some devices default
#set-default-sink output
#set-default-source input

Présence confirmée

5 - Vérification du firmware utilisé par la carte :

root@sweet-GS60-6QC:~# ethtool -i wlp2s0
driver: ath10k_pci
version: 4.10.0-32-generic
firmware-version: SW_RM.1.1.1-00157-QCARMSWPZ-1
expansion-rom-version: 
bus-info: 0000:02:00.0
supports-statistics: yes
supports-test: no
supports-eeprom-access: no
supports-register-dump: no
supports-priv-flags: no

Présence de deux dossiers firmware (le firmware contenu dans hw2.1 est utilisé (peut être faut il utiliser celui contenu dans le dossier hw3.0  mais je ne sais pas comment procéder, si quelqu’un sait...) 

root@sweet-GS60-6QC:~# ls /lib/firmware/ath10k/QCA6174/
hw2.1  hw3.0

Edit 24/08/2017:

6 - Visite sur le site du constructeur Killer networking site

Commandes effectuées

wget http://mirrors.kernel.org/ubuntu/pool/main/l/linux-firmware/linux-firmware_1.164_all.deb
sudo dpkg -i linux-firmware*.deb
sudo modprobe -r ath10k_pci && sudo modprobe ath10k_pci

résultat : Aucun changement

INFO :

Service toujours vu comme actif , peut être stoppé et redémarré mais n'a aucun impact sur la carte ou le voyant bluetooth

sweet@sweet-GS60-6QC:~$ service bluetooth status
● bluetooth.service - Bluetooth service
   Loaded: loaded (/lib/systemd/system/bluetooth.service; enabled; vendor preset
   Active: active (running) since jeu. 2017-08-24 16:13:36 CEST; 2h 6min ago
     Docs: man:bluetoothd(8)
 Main PID: 1252 (bluetoothd)
   Status: "Running"
   CGroup: /system.slice/bluetooth.service
           └─1252 /usr/lib/bluetooth/bluetoothd

août 24 16:13:36 sweet-GS60-6QC systemd[1]: Starting Bluetooth service...
août 24 16:13:36 sweet-GS60-6QC bluetoothd[1252]: Bluetooth daemon 5.37
août 24 16:13:36 sweet-GS60-6QC systemd[1]: Started Bluetooth service.
août 24 16:13:36 sweet-GS60-6QC bluetoothd[1252]: Starting SDP server
août 24 16:13:36 sweet-GS60-6QC bluetoothd[1252]: Bluetooth management interface
lines 1-14/14 (END)

EDIT 2 - 25/08/2017:
Hypothèse numéro 7 :

D'après la commande suivante :

oot@sweet-GS60-6QC:~# uname -a; lspci -nnk | grep -iA2 net; lsusb; dmesg | grep -i bluetooth; dmesg | grep -i firmware; lsmod | grep bluetooth

Résultat :

oot@sweet-GS60-6QC:~# uname -a; lspci -nnk | grep -iA2 net; lsusb; dmesg | grep -i bluetooth; dmesg | grep -i firmware; lsmod | grep bluetooth
Linux sweet-GS60-6QC 4.10.0-32-generic #36~16.04.1-Ubuntu SMP Wed Aug 9 09:19:02 UTC 2017 x86_64 x86_64 x86_64 GNU/Linux
02:00.0 Network controller [0280]: Qualcomm Atheros QCA6174 802.11ac Wireless Network Adapter [168c:003e] (rev 20)
    Subsystem: Bigfoot Networks, Inc. Killer N1525 Wireless-AC [1a56:1525]
    Kernel driver in use: ath10k_pci
    Kernel modules: ath10k_pci
--
04:00.0 Ethernet controller [0200]: Qualcomm Atheros Killer E2400 Gigabit Ethernet Controller [1969:e0a1] (rev 10)
    Subsystem: Micro-Star International Co., Ltd. [MSI] Killer E2400 Gigabit Ethernet Controller [1462:116b]
    Kernel driver in use: alx
    Kernel modules: alx
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 002: ID 1770:ff00 
Bus 001 Device 004: ID 12c9:1001 
Bus 001 Device 003: ID 0cf3:3004 Atheros Communications, Inc. AR3012 Bluetooth 4.0
Bus 001 Device 005: ID 1c4f:0024 SiGma Micro
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
[    2.275507] Bluetooth: Core ver 2.22
[    2.275519] Bluetooth: HCI device and connection manager initialized
[    2.275521] Bluetooth: HCI socket layer initialized
[    2.275523] Bluetooth: L2CAP socket layer initialized
[    2.275527] Bluetooth: SCO socket layer initialized
[    2.282031] Bluetooth: HCI UART driver ver 2.3
[    2.282033] Bluetooth: HCI UART protocol H4 registered
[    2.282033] Bluetooth: HCI UART protocol BCSP registered
[    2.282034] Bluetooth: HCI UART protocol LL registered
[    2.282035] Bluetooth: HCI UART protocol ATH3K registered
[    2.282035] Bluetooth: HCI UART protocol Three-wire (H5) registered
[    2.284488] Bluetooth: HCI UART protocol Intel registered
[    2.284515] Bluetooth: HCI UART protocol Broadcom registered
[    2.284515] Bluetooth: HCI UART protocol QCA registered
[    2.284516] Bluetooth: HCI UART protocol AG6XX registered
[    2.284517] Bluetooth: HCI UART protocol Marvell registered
[    2.360468] Bluetooth: Patch file not found ar3k/AthrBT_0x00000200.dfu
[    2.360470] Bluetooth: Loading patch file failed
[   14.387983] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   14.387985] Bluetooth: BNEP filters: protocol multicast
[   14.387988] Bluetooth: BNEP socket layer initialized
[    0.177108] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
[    1.142861] [drm] GuC firmware load skipped
[    1.631986] psmouse serio1: elantech: assuming hardware version 4 (with firmware version 0x361f00)
[    2.360466] usb 1-10: Direct firmware load for ar3k/AthrBT_0x00000200.dfu failed with error -2
[    2.630608] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:02:00.0.bin failed with error -2
[    2.630615] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/cal-pci-0000:02:00.0.bin failed with error -2
[    2.631895] ath10k_pci 0000:02:00.0: firmware ver SW_RM.1.1.1-00157-QCARMSWPZ-1 api 5 features ignore-otp,no-4addr-pad crc32 10bf8e08
bluetooth             557056  14 btrtl,hci_uart,btintel,btqca,bnep,btbcm,ath3k,btusb

Dans les dernières lignes je constate certaines erreurs (certains fichiers ne peuvent être trouvés)

[    2.360468] Bluetooth: Patch file not found ar3k/AthrBT_0x00000200.dfu
[    2.360470] Bluetooth: Loading patch file failed
[   14.387983] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   14.387985] Bluetooth: BNEP filters: protocol multicast
[   14.387988] Bluetooth: BNEP socket layer initialized
[    0.177108] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
[    1.142861] [drm] GuC firmware load skipped
[    1.631986] psmouse serio1: elantech: assuming hardware version 4 (with firmware version 0x361f00)
[    2.360466] usb 1-10: Direct firmware load for ar3k/AthrBT_0x00000200.dfu failed with error -2
[    2.630608] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:02:00.0.bin failed with error -2
[    2.630615] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/cal-pci-0000:02:00.0.bin failed with error -2
[    2.631895] ath10k_pci 0000:02:00.0: firmware ver SW_RM.1.1.1-00157-QCARMSWPZ-1 api 5 features ignore-otp,no-4addr-pad crc32 10bf8e08
bluetooth             557056  14 btrtl,hci_uart,btintel,btqca,bnep,btbcm,ath3k,btusb

L'avis d'un expert serait le bienvenu smile

Dernière modification par Sweery (Le 25/08/2017, à 08:51)

Hors ligne

#20 Le 25/08/2017, à 08:52

xubu1957

Re : [Résolu] : MSI GS60 6QC 231XFR -- Ubuntu 16.04 -- Bluetooth inexistant

Bonjour,

C'est pour une carte BCM43142, mais regarde le processus utilisé > [ RÉSOLU ] Bluetooth activé, mais ne détecte rien


Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Résolu] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci.                   Membre de Linux-Azur

Hors ligne

#21 Le 25/08/2017, à 09:18

Sweery

Re : [Résolu] : MSI GS60 6QC 231XFR -- Ubuntu 16.04 -- Bluetooth inexistant

Bonjour,

Alors voici déjà un retour sur les commandes :

rfkill list
rfkill unblock all
hciconfig hci0 up

Résultat :

root@sweet-GS60-6QC:~# rfkill list
0: phy0: Wireless LAN
	Soft blocked: no
	Hard blocked: no
root@sweet-GS60-6QC:~# rfkill unblock all
root@sweet-GS60-6QC:~# rfkill list
0: phy0: Wireless LAN
	Soft blocked: no
	Hard blocked: no
root@sweet-GS60-6QC:~# hciconfig hci0 up
Can't get device info: No such device
root@sweet-GS60-6QC:~# hcitool dev
Devices:
root@sweet-GS60-6QC:~# hciconfig
root@sweet-GS60-6QC:~# hcitool scan
Device is not available: No such device

Je regarde le reste de la page et je vous tient au courant pour les autres solutions (pour l'instant le périphérique ne semble pas présent)

Dernière modification par Sweery (Le 25/08/2017, à 09:21)

Hors ligne

#22 Le 25/08/2017, à 11:24

Sweery

Re : [Résolu] : MSI GS60 6QC 231XFR -- Ubuntu 16.04 -- Bluetooth inexistant

Concernant la conversion de drivers microsoft .hex en .hcd , il semble que cela soit spécifique à Broadcom, Cependant cela m'a donné quelques pistes. Ainsi d'après les erreurs si dessous et d'après le CD de drivers du PC j'ai trouvé le fichier manquant AthrBT_0x00000200.dfu. je l'ai copié dans le répertoire /lib/firmware/ar3k et l'erreur n’apparaît plus , par contre ce fichier ne correspond plus au firmware ath10k (pour moi ath10k semble obsolète car le fichier AthrBT_0x00000200.dfu provient directement du CD-ROM de driver du pc, qui je suppose est le plus récent "acheté dans le mois")

Erreurs avant copie du fichier

oot@sweet-GS60-6QC:~# uname -a; lspci -nnk | grep -iA2 net; lsusb; dmesg | grep -i bluetooth; dmesg | grep -i firmware; lsmod | grep bluetooth
Linux sweet-GS60-6QC 4.10.0-32-generic #36~16.04.1-Ubuntu SMP Wed Aug 9 09:19:02 UTC 2017 x86_64 x86_64 x86_64 GNU/Linux
02:00.0 Network controller [0280]: Qualcomm Atheros QCA6174 802.11ac Wireless Network Adapter [168c:003e] (rev 20)
    Subsystem: Bigfoot Networks, Inc. Killer N1525 Wireless-AC [1a56:1525]
    Kernel driver in use: ath10k_pci
    Kernel modules: ath10k_pci
--
04:00.0 Ethernet controller [0200]: Qualcomm Atheros Killer E2400 Gigabit Ethernet Controller [1969:e0a1] (rev 10)
    Subsystem: Micro-Star International Co., Ltd. [MSI] Killer E2400 Gigabit Ethernet Controller [1462:116b]
    Kernel driver in use: alx
    Kernel modules: alx
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 002: ID 1770:ff00 
Bus 001 Device 004: ID 12c9:1001 
Bus 001 Device 003: ID 0cf3:3004 Atheros Communications, Inc. AR3012 Bluetooth 4.0
Bus 001 Device 005: ID 1c4f:0024 SiGma Micro
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
[    2.275507] Bluetooth: Core ver 2.22
[    2.275519] Bluetooth: HCI device and connection manager initialized
[    2.275521] Bluetooth: HCI socket layer initialized
[    2.275523] Bluetooth: L2CAP socket layer initialized
[    2.275527] Bluetooth: SCO socket layer initialized
[    2.282031] Bluetooth: HCI UART driver ver 2.3
[    2.282033] Bluetooth: HCI UART protocol H4 registered
[    2.282033] Bluetooth: HCI UART protocol BCSP registered
[    2.282034] Bluetooth: HCI UART protocol LL registered
[    2.282035] Bluetooth: HCI UART protocol ATH3K registered
[    2.282035] Bluetooth: HCI UART protocol Three-wire (H5) registered
[    2.284488] Bluetooth: HCI UART protocol Intel registered
[    2.284515] Bluetooth: HCI UART protocol Broadcom registered
[    2.284515] Bluetooth: HCI UART protocol QCA registered
[    2.284516] Bluetooth: HCI UART protocol AG6XX registered
[    2.284517] Bluetooth: HCI UART protocol Marvell registered
[    2.360468] Bluetooth: Patch file not found ar3k/AthrBT_0x00000200.dfu
[    2.360470] Bluetooth: Loading patch file failed
[   14.387983] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   14.387985] Bluetooth: BNEP filters: protocol multicast
[   14.387988] Bluetooth: BNEP socket layer initialized
[    0.177108] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
[    1.142861] [drm] GuC firmware load skipped
[    1.631986] psmouse serio1: elantech: assuming hardware version 4 (with firmware version 0x361f00)
[    2.360466] usb 1-10: Direct firmware load for ar3k/AthrBT_0x00000200.dfu failed with error -2
[    2.630608] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:02:00.0.bin failed with error -2
[    2.630615] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/cal-pci-0000:02:00.0.bin failed with error -2
[    2.631895] ath10k_pci 0000:02:00.0: firmware ver SW_RM.1.1.1-00157-QCARMSWPZ-1 api 5 features ignore-otp,no-4addr-pad crc32 10bf8e08
bluetooth             557056  14 btrtl,hci_uart,btintel,btqca,bnep,btbcm,ath3k,btusb

Résultat Après copie

sweet@sweet-GS60-6QC:~$ uname -a; lspci -nnk | grep -iA2 net; lsusb; dmesg | grep -i bluetooth; dmesg | grep -i firmware; lsmod | grep bluetooth
Linux sweet-GS60-6QC 4.10.0-32-generic #36~16.04.1-Ubuntu SMP Wed Aug 9 09:19:02 UTC 2017 x86_64 x86_64 x86_64 GNU/Linux
02:00.0 Network controller [0280]: Qualcomm Atheros QCA6174 802.11ac Wireless Network Adapter [168c:003e] (rev 20)
	Subsystem: Bigfoot Networks, Inc. Killer N1525 Wireless-AC [1a56:1525]
	Kernel driver in use: ath10k_pci
	Kernel modules: ath10k_pci
--
04:00.0 Ethernet controller [0200]: Qualcomm Atheros Killer E2400 Gigabit Ethernet Controller [1969:e0a1] (rev 10)
	Subsystem: Micro-Star International Co., Ltd. [MSI] Killer E2400 Gigabit Ethernet Controller [1462:116b]
	Kernel driver in use: alx
	Kernel modules: alx
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 004: ID 1770:ff00  
Bus 001 Device 003: ID 05e3:0715 Genesys Logic, Inc. USB 2.0 microSD Reader
Bus 001 Device 005: ID 0cf3:3004 Atheros Communications, Inc. AR3012 Bluetooth 4.0
Bus 001 Device 006: ID 12c9:1001  
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
[    1.999212] Bluetooth: Core ver 2.22
[    1.999225] Bluetooth: HCI device and connection manager initialized
[    1.999229] Bluetooth: HCI socket layer initialized
[    1.999231] Bluetooth: L2CAP socket layer initialized
[    1.999235] Bluetooth: SCO socket layer initialized
[    2.005870] Bluetooth: HCI UART driver ver 2.3
[    2.005872] Bluetooth: HCI UART protocol H4 registered
[    2.005873] Bluetooth: HCI UART protocol BCSP registered
[    2.005874] Bluetooth: HCI UART protocol LL registered
[    2.005874] Bluetooth: HCI UART protocol ATH3K registered
[    2.005875] Bluetooth: HCI UART protocol Three-wire (H5) registered
[    2.005956] Bluetooth: HCI UART protocol Intel registered
[    2.005982] Bluetooth: HCI UART protocol Broadcom registered
[    2.005982] Bluetooth: HCI UART protocol QCA registered
[    2.005983] Bluetooth: HCI UART protocol AG6XX registered
[    2.005983] Bluetooth: HCI UART protocol Marvell registered
[    2.981803] Bluetooth: Patch file version did not match with firmware
[    2.981808] Bluetooth: Loading patch file failed
[    7.073264] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    7.073265] Bluetooth: BNEP filters: protocol multicast
[    7.073269] Bluetooth: BNEP socket layer initialized
[    0.176949] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
[    1.133330] [drm] GuC firmware load skipped
[    1.631695] psmouse serio1: elantech: assuming hardware version 4 (with firmware version 0x361f00)
[    2.358858] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:02:00.0.bin failed with error -2
[    2.358865] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/cal-pci-0000:02:00.0.bin failed with error -2
[    2.360152] ath10k_pci 0000:02:00.0: firmware ver SW_RM.1.1.1-00157-QCARMSWPZ-1 api 5 features ignore-otp,no-4addr-pad crc32 10bf8e08
[    2.981803] Bluetooth: Patch file version did not match with firmware
bluetooth             557056  14 btrtl,hci_uart,btintel,btqca,bnep,btbcm,ath3k,btusb

Je regarde actuellement si il est possible d'utiliser le firmware.bin de microsoft à la place du ath10k présent dans /lib/firmware/ath10k/QCA6174.
Je vais également tenté une mise à jour via le dépôt de git (bien que le firmware présent sur dépôt semble être celui que je possède déjà)

sinon à part ça aucun changement notable pour l'instant

EDIT : je rassemblerai toutes les solutions au fur et à mesure pour un meilleur suivi (n'hésitez pas a intervenir , toutes les pistes concernant les drivers peuvent aboutir à des solutions smile )

Dernière modification par Sweery (Le 25/08/2017, à 14:12)

Hors ligne

#23 Le 25/08/2017, à 15:26

xubu1957

Re : [Résolu] : MSI GS60 6QC 231XFR -- Ubuntu 16.04 -- Bluetooth inexistant


Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Résolu] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci.                   Membre de Linux-Azur

Hors ligne

#24 Le 25/08/2017, à 15:52

ylag

Re : [Résolu] : MSI GS60 6QC 231XFR -- Ubuntu 16.04 -- Bluetooth inexistant

Hors ligne

#25 Le 25/08/2017, à 16:11

Sweery

Re : [Résolu] : MSI GS60 6QC 231XFR -- Ubuntu 16.04 -- Bluetooth inexistant

Analyse  en cours ... merci pour vos réponses smile (solutions 9 et 10 en cours...) rapport demain

Dernière modification par Sweery (Le 25/08/2017, à 23:24)

Hors ligne