Disque dur externe ne monte pas

Pedro31077 · Le 12/03/2020, à 15:43

Bonjour
suite à une manip malheureuse (début de re-initialisation du disque externe, annulée rapidement dès que je me suis rendu compte de l'erreur) j'ai perdu tout accès à mon disque externe.
Pas grave au niveau des données perdues car ce n'étaient que des doublages de sauvegarde, mais ça fait ch... pour le matériel parce que c'est un Sony 500Go qui, en principe, fonctionne très bien.
Il est toujours reconnu sur lsusb :

Bus 002 Device 004: ID 0bda:0129 Realtek Semiconductor Corp. RTS5129 Card Reader Controller
Bus 002 Device 003: ID 054c:05bf Sony Corp. 
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 004: ID 04ca:0050 Lite-On Technology Corp. 
Bus 001 Device 003: ID 0461:4e2b Primax Electronics, Ltd 
Bus 001 Device 005: ID 03f0:df11 Hewlett-Packard 
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

par contre, je ne retrouve pas par fdisk -l :

Disque /dev/loop0 : 140,7 MiB, 147501056 octets, 288088 secteurs
Unités : secteur de 1 × 512 = 512 octets
Taille de secteur (logique / physique) : 512 octets / 512 octets
taille d'E/S (minimale / optimale) : 512 octets / 512 octets
etc ...
Disque /dev/sda : 931,5 GiB, 1000204886016 octets, 1953525168 secteurs
Unités : secteur de 1 × 512 = 512 octets
Taille de secteur (logique / physique) : 512 octets / 4096 octets
taille d'E/S (minimale / optimale) : 4096 octets / 4096 octets
Type d'étiquette de disque : dos
Identifiant de disque : 0xc18c694e

Périphérique Amorçage      Début        Fin   Secteurs Taille Id Type
/dev/sda1    *              2048     206847     204800   100M  7 HPFS/NTFS/exFAT
/dev/sda2                 206848  819202047  818995200 390,5G  7 HPFS/NTFS/exFAT
/dev/sda3              819204094 1953523711 1134319618 540,9G  5 Étendue
/dev/sda5             1945237504 1953523711    8286208     4G 82 partition d'éch
/dev/sda6              819204096 1945237503 1126033408   537G 83 Linux

La partition 3 ne commence pas sur une frontière de cylindre physique.
Les entrées de la table de partitions ne sont pas dans l'ordre du disque.

Disque /dev/sdb : 465,8 GiB, 500107859968 octets, 976773164 secteurs
Unités : secteur de 1 × 512 = 512 octets
Taille de secteur (logique / physique) : 512 octets / 512 octets
taille d'E/S (minimale / optimale) : 512 octets / 512 octets
Type d'étiquette de disque : dos
Identifiant de disque : 0xa13c88e4

Périphérique Amorçage Début       Fin  Secteurs Taille Id Type
/dev/sdb1              2048 976773119 976771072 465,8G  5 Étendue

Disque /dev/loop8 : 160,2 MiB, 167931904 octets, 327992 secteurs
Unités : secteur de 1 × 512 = 512 octets
Taille de secteur (logique / physique) : 512 octets / 512 octets
taille d'E/S (minimale / optimale) : 512 octets / 512 octets
etc ...
Disque /dev/loop20 : 3,7 MiB, 3825664 octets, 7472 secteurs
Unités : secteur de 1 × 512 = 512 octets
Taille de secteur (logique / physique) : 512 octets / 512 octets
taille d'E/S (minimale / optimale) : 512 octets / 512 octets
pierre@pierre-Aspire-MC605

Pour faire court : mon DD Sony est bien reconnu en tant que tel, y compris par gnome-disk-utility 3.28.3, mais il ne monte pas, et je n'ai pas accès à son SMART.
Faute d'expérience, je ne me suis pas lancé dans les autre possibilités (modifier la partition, etc)
Quelqu'un de mieux expérimenté que moi aurait-il une solution pour que la bestiole accepte d'être montée ?
Merci d'avance

Watts · Le 12/03/2020, à 16:06

Bonjour,

Pour des aidants plus aguerris, branche ton disque, puis attends 10 secondes et retourne la fin de:

dmesg

Pedro31077 · Le 12/03/2020, à 16:21

Voilà la fin du retour, toute la partie audit :

[ 1985.528898] audit: type=1400 audit(1584019954.489:136): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/usr/share/nvidia/nvidia-application-profiles-390.116-rc" pid=5953 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 1985.535497] audit: type=1400 audit(1584019954.493:137): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/usr/share/nvidia/nvidia-application-profiles-390.116-rc" pid=5953 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 1985.544197] audit: type=1400 audit(1584019954.505:138): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/modules" pid=5953 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 1985.544379] audit: type=1400 audit(1584019954.505:139): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/driver/nvidia/params" pid=5953 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 1985.544389] audit: type=1400 audit(1584019954.505:140): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/dev/nvidiactl" pid=5953 comm="soffice.bin" requested_mask="wr" denied_mask="wr" fsuid=1000 ouid=0
[ 1985.544391] audit: type=1400 audit(1584019954.505:141): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/sys/devices/system/memory/block_size_bytes" pid=5953 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 1985.544415] audit: type=1400 audit(1584019954.505:142): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/modules" pid=5953 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 1985.544442] audit: type=1400 audit(1584019954.505:143): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/driver/nvidia/params" pid=5953 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 1985.544464] audit: type=1400 audit(1584019954.505:144): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/dev/nvidia-modeset" pid=5953 comm="soffice.bin" requested_mask="wr" denied_mask="wr" fsuid=1000 ouid=0
[ 1985.544510] audit: type=1400 audit(1584019954.505:145): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/driver/nvidia/params" pid=5953 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 2137.797721] usblp0: removed
[ 2576.217815] kauditd_printk_skb: 59 callbacks suppressed
[ 2576.217825] audit: type=1400 audit(1584020545.176:205): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/usr/share/nvidia/nvidia-application-profiles-390.116-rc" pid=6115 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 2576.331433] audit: type=1400 audit(1584020545.288:206): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/usr/share/nvidia/nvidia-application-profiles-390.116-rc" pid=6115 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 2576.340305] audit: type=1400 audit(1584020545.300:207): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/modules" pid=6115 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 2576.340335] audit: type=1400 audit(1584020545.300:208): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/driver/nvidia/params" pid=6115 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 2576.340360] audit: type=1400 audit(1584020545.300:209): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/dev/nvidiactl" pid=6115 comm="soffice.bin" requested_mask="wr" denied_mask="wr" fsuid=1000 ouid=0
[ 2576.340383] audit: type=1400 audit(1584020545.300:210): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/sys/devices/system/memory/block_size_bytes" pid=6115 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 2576.340478] audit: type=1400 audit(1584020545.300:211): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/modules" pid=6115 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 2576.340509] audit: type=1400 audit(1584020545.300:212): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/driver/nvidia/params" pid=6115 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 2576.340527] audit: type=1400 audit(1584020545.300:213): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/dev/nvidia-modeset" pid=6115 comm="soffice.bin" requested_mask="wr" denied_mask="wr" fsuid=1000 ouid=0
[ 2576.340591] audit: type=1400 audit(1584020545.300:214): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/driver/nvidia/params" pid=6115 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 3437.999628]  sdb: sdb1 < >
[ 3656.297080] kauditd_printk_skb: 59 callbacks suppressed
[ 3656.297089] audit: type=1400 audit(1584021625.257:274): apparmor="DENIED" operation="open" profile="/usr/bin/freshclam" name="/etc/ssl/openssl.cnf" pid=1194 comm="freshclam" requested_mask="r" denied_mask="r" fsuid=127 ouid=0
[ 6727.880671] audit: type=1400 audit(1584024696.843:275): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/usr/share/nvidia/nvidia-application-profiles-390.116-rc" pid=6987 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 6727.888775] audit: type=1400 audit(1584024696.851:276): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/usr/share/nvidia/nvidia-application-profiles-390.116-rc" pid=6987 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 6727.899164] audit: type=1400 audit(1584024696.859:277): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/modules" pid=6987 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 6727.899196] audit: type=1400 audit(1584024696.859:278): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/driver/nvidia/params" pid=6987 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 6727.899247] audit: type=1400 audit(1584024696.859:279): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/dev/nvidiactl" pid=6987 comm="soffice.bin" requested_mask="wr" denied_mask="wr" fsuid=1000 ouid=0
[ 6727.899257] audit: type=1400 audit(1584024696.859:280): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/sys/devices/system/memory/block_size_bytes" pid=6987 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 6727.899377] audit: type=1400 audit(1584024696.859:281): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/modules" pid=6987 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 6727.899405] audit: type=1400 audit(1584024696.859:282): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/driver/nvidia/params" pid=6987 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 6727.899433] audit: type=1400 audit(1584024696.859:283): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/dev/nvidia-modeset" pid=6987 comm="soffice.bin" requested_mask="wr" denied_mask="wr" fsuid=1000 ouid=0
[ 6727.899483] audit: type=1400 audit(1584024696.859:284): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/driver/nvidia/params" pid=6987 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0

Watts · Le 12/03/2020, à 16:34

Puisque les infos ne sont pas celles que je recherchais, recommence la manipulation et donne le retour complet de:

dmesg

Pedro31077 · Le 12/03/2020, à 16:53

Voilà l'intégralité du retour :

pierre@pierre-Aspire-MC605:~$ dmesg
[    0.000000] microcode: microcode updated early to revision 0x21, date = 2019-02-13
[    0.000000] Linux version 4.15.0-88-generic (buildd@lgw01-amd64-036) (gcc version 7.4.0 (Ubuntu 7.4.0-1ubuntu1~18.04.1)) #88-Ubuntu SMP Tue Feb 11 20:11:34 UTC 2020 (Ubuntu 4.15.0-88.88-generic 4.15.18)
[    0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-4.15.0-88-generic root=UUID=d18ce4fe-4c63-4273-8de3-17c035816097 ro quiet splash vt.handoff=1
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   Centaur CentaurHauls
[    0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
[    0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[    0.000000] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers'
[    0.000000] x86/fpu: xstate_offset[2]:  576, xstate_sizes[2]:  256
[    0.000000] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format.
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009d7ff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009d800-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000dd7cefff] usable
[    0.000000] BIOS-e820: [mem 0x00000000dd7cf000-0x00000000dd86efff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000dd86f000-0x00000000dd87ffff] ACPI data
[    0.000000] BIOS-e820: [mem 0x00000000dd880000-0x00000000de10dfff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000de10e000-0x00000000ded96fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ded97000-0x00000000dedd9fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000dedda000-0x00000000df59bfff] usable
[    0.000000] BIOS-e820: [mem 0x00000000df59c000-0x00000000df7f0fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000df7f1000-0x00000000df7fffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed03fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000011effffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.7 present.
[    0.000000] DMI: Acer Aspire MC605/Aspire MC605, BIOS P11-A4                  04/10/2013
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] e820: last_pfn = 0x11f000 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-CFFFF write-protect
[    0.000000]   D0000-E7FFF uncachable
[    0.000000]   E8000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask F00000000 write-back
[    0.000000]   1 base 100000000 mask FF0000000 write-back
[    0.000000]   2 base 110000000 mask FF8000000 write-back
[    0.000000]   3 base 118000000 mask FFC000000 write-back
[    0.000000]   4 base 11C000000 mask FFE000000 write-back
[    0.000000]   5 base 11E000000 mask FFF000000 write-back
[    0.000000]   6 base 0E0000000 mask FE0000000 uncachable
[    0.000000]   7 disabled
[    0.000000]   8 disabled
[    0.000000]   9 disabled
[    0.000000] x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WP  UC- WT  
[    0.000000] total RAM covered: 4080M
[    0.000000] Found optimal setting for mtrr clean up
[    0.000000]  gran_size: 64K 	chunk_size: 32M 	num_reg: 5  	lose cover RAM: 0G
[    0.000000] e820: update [mem 0xe0000000-0xffffffff] usable ==> reserved
[    0.000000] e820: last_pfn = 0xdf800 max_arch_pfn = 0x400000000
[    0.000000] found SMP MP-table at [mem 0x000fd7d0-0x000fd7df]
[    0.000000] Scanning 1 areas for low memory corruption
[    0.000000] BRK [0x23990000, 0x23990fff] PGTABLE
[    0.000000] BRK [0x23991000, 0x23991fff] PGTABLE
[    0.000000] BRK [0x23992000, 0x23992fff] PGTABLE
[    0.000000] BRK [0x23993000, 0x23993fff] PGTABLE
[    0.000000] BRK [0x23994000, 0x23994fff] PGTABLE
[    0.000000] BRK [0x23995000, 0x23995fff] PGTABLE
[    0.000000] BRK [0x23996000, 0x23996fff] PGTABLE
[    0.000000] BRK [0x23997000, 0x23997fff] PGTABLE
[    0.000000] BRK [0x23998000, 0x23998fff] PGTABLE
[    0.000000] BRK [0x23999000, 0x23999fff] PGTABLE
[    0.000000] RAMDISK: [mem 0x334cb000-0x35a5cfff]
[    0.000000] ACPI: Early table checksum verification disabled
[    0.000000] ACPI: RSDP 0x00000000000F0490 000024 (v02 ACRSYS)
[    0.000000] ACPI: XSDT 0x00000000DD872080 00007C (v01 ACRSYS ACRPRDCT 01072009 AMI  00010013)
[    0.000000] ACPI: FACP 0x00000000DD87DD08 00010C (v05 ACRSYS ACRPRDCT 01072009 AMI  00010013)
[    0.000000] ACPI: DSDT 0x00000000DD872188 00BB7D (v02 ACRSYS ACRPRDCT 00000022 INTL 20051117)
[    0.000000] ACPI: FACS 0x00000000DE10C080 000040
[    0.000000] ACPI: APIC 0x00000000DD87DE18 000072 (v03 ACRSYS ACRPRDCT 01072009 AMI  00010013)
[    0.000000] ACPI: FPDT 0x00000000DD87DE90 000044 (v01 ACRSYS ACRPRDCT 01072009 AMI  00010013)
[    0.000000] ACPI: ASF! 0x00000000DD87DED8 0000A5 (v32 INTEL   HCG     00000001 TFSM 000F4240)
[    0.000000] ACPI: MCFG 0x00000000DD87DF80 00003C (v01 ACRSYS ACRPRDCT 01072009 MSFT 00000097)
[    0.000000] ACPI: MSDM 0x00000000DD87DFC0 000055 (v03 ACRSYS ACRPRDCT 01072009 AMI  00010013)
[    0.000000] ACPI: SLIC 0x00000000DD87E018 000176 (v01 ACRSYS ACRPRDCT 01072000 AMI  00010013)
[    0.000000] ACPI: HPET 0x00000000DD87E190 000038 (v01 ACRSYS ACRPRDCT 01072009 AMI. 00000005)
[    0.000000] ACPI: SSDT 0x00000000DD87E1C8 00036D (v01 SataRe SataTabl 00001000 INTL 20091112)
[    0.000000] ACPI: SSDT 0x00000000DD87E538 0009AA (v01 PmRef  Cpu0Ist  00003000 INTL 20051117)
[    0.000000] ACPI: SSDT 0x00000000DD87EEE8 000A92 (v01 PmRef  CpuPm    00003000 INTL 20051117)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at [mem 0x0000000000000000-0x000000011effffff]
[    0.000000] NODE_DATA(0) allocated [mem 0x11efd3000-0x11effdfff]
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000001000-0x0000000000ffffff]
[    0.000000]   DMA32    [mem 0x0000000001000000-0x00000000ffffffff]
[    0.000000]   Normal   [mem 0x0000000100000000-0x000000011effffff]
[    0.000000]   Device   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000001000-0x000000000009cfff]
[    0.000000]   node   0: [mem 0x0000000000100000-0x00000000dd7cefff]
[    0.000000]   node   0: [mem 0x00000000dedda000-0x00000000df59bfff]
[    0.000000]   node   0: [mem 0x00000000df7f1000-0x00000000df7fffff]
[    0.000000]   node   0: [mem 0x0000000100000000-0x000000011effffff]
[    0.000000] Reserved but unavailable: 100 pages
[    0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000011effffff]
[    0.000000] On node 0 totalpages: 1036092
[    0.000000]   DMA zone: 64 pages used for memmap
[    0.000000]   DMA zone: 21 pages reserved
[    0.000000]   DMA zone: 3996 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 14143 pages used for memmap
[    0.000000]   DMA32 zone: 905120 pages, LIFO batch:31
[    0.000000]   Normal zone: 1984 pages used for memmap
[    0.000000]   Normal zone: 126976 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[    0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[    0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
[    0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[    0.000000] PM: Registered nosave memory: [mem 0x0009d000-0x0009dfff]
[    0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[    0.000000] PM: Registered nosave memory: [mem 0xdd7cf000-0xdd86efff]
[    0.000000] PM: Registered nosave memory: [mem 0xdd86f000-0xdd87ffff]
[    0.000000] PM: Registered nosave memory: [mem 0xdd880000-0xde10dfff]
[    0.000000] PM: Registered nosave memory: [mem 0xde10e000-0xded96fff]
[    0.000000] PM: Registered nosave memory: [mem 0xded97000-0xdedd9fff]
[    0.000000] PM: Registered nosave memory: [mem 0xdf59c000-0xdf7f0fff]
[    0.000000] PM: Registered nosave memory: [mem 0xdf800000-0xf7ffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfbffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfc000000-0xfebfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfecfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfed03fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed04000-0xfed1bfff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed20000-0xfedfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xfeffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xff000000-0xffffffff]
[    0.000000] e820: [mem 0xdf800000-0xf7ffffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
[    0.000000] random: get_random_bytes called from start_kernel+0x99/0x4fd with crng_init=0
[    0.000000] setup_percpu: NR_CPUS:8192 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1
[    0.000000] percpu: Embedded 45 pages/cpu s147456 r8192 d28672 u524288
[    0.000000] pcpu-alloc: s147456 r8192 d28672 u524288 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 1019880
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.15.0-88-generic root=UUID=d18ce4fe-4c63-4273-8de3-17c035816097 ro quiet splash vt.handoff=1
[    0.000000] Calgary: detecting Calgary via BIOS EBDA area
[    0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.000000] Memory: 3945096K/4144368K available (12300K kernel code, 2481K rwdata, 4264K rodata, 2428K init, 2712K bss, 199272K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Kernel/User page tables isolation: enabled
[    0.000000] ftrace: allocating 39344 entries in 154 pages
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=4.
[    0.000000] 	Tasks RCU enabled.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 524544, nr_irqs: 456, preallocated irqs: 16
[    0.000000] vt handoff: transparent VT on vt#1
[    0.000000] Console: colour dummy device 80x25
[    0.000000] console [tty0] enabled
[    0.000000] ACPI: Core revision 20170831
[    0.000000] ACPI: 4 ACPI AML tables successfully acquired and loaded
[    0.000000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484882848 ns
[    0.000000] hpet clockevent registered
[    0.000000] APIC: Switch to symmetric I/O mode setup
[    0.000000] x2apic: IRQ remapping doesn't support X2APIC mode
[    0.000000] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.020000] tsc: Fast TSC calibration using PIT
[    0.024000] tsc: Detected 3093.079 MHz processor
[    0.024000] Calibrating delay loop (skipped), value calculated using timer frequency.. 6186.15 BogoMIPS (lpj=12372316)
[    0.024000] pid_max: default: 32768 minimum: 301
[    0.024000] Security Framework initialized
[    0.024000] Yama: becoming mindful.
[    0.024000] AppArmor: AppArmor initialized
[    0.028312] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.028687] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.028706] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.028719] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.028893] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[    0.028894] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[    0.028905] CPU0: Thermal monitoring enabled (TM1)
[    0.028914] process: using mwait in idle threads
[    0.028917] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 8
[    0.028917] Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32, 1GB 0
[    0.028918] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization
[    0.028920] Spectre V2 : Mitigation: Full generic retpoline
[    0.028920] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[    0.028920] Spectre V2 : Enabling Restricted Speculation for firmware calls
[    0.028926] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier
[    0.028927] Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl and seccomp
[    0.028950] MDS: Mitigation: Clear CPU buffers
[    0.029114] Freeing SMP alternatives memory: 36K
[    0.030980] TSC deadline timer enabled
[    0.030983] smpboot: CPU0: Intel(R) Core(TM) i5-3350P CPU @ 3.10GHz (family: 0x6, model: 0x3a, stepping: 0x9)
[    0.031041] Performance Events: PEBS fmt1+, IvyBridge events, 16-deep LBR, full-width counters, Intel PMU driver.
[    0.031060] ... version:                3
[    0.031060] ... bit width:              48
[    0.031060] ... generic registers:      8
[    0.031061] ... value mask:             0000ffffffffffff
[    0.031061] ... max period:             00007fffffffffff
[    0.031062] ... fixed-purpose events:   3
[    0.031062] ... event mask:             00000007000000ff
[    0.031094] Hierarchical SRCU implementation.
[    0.031833] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
[    0.031846] smp: Bringing up secondary CPUs ...
[    0.031914] x86: Booting SMP configuration:
[    0.031915] .... node  #0, CPUs:      #1
[    0.032000] TSC synchronization [CPU#0 -> CPU#1]:
[    0.032000] Measured 33554671 cycles TSC warp between CPUs, turning off TSC clock.
[    0.032000] tsc: Marking TSC unstable due to check_tsc_sync_source failed
[    0.032089]  #2 #3
[    0.032905] smp: Brought up 1 node, 4 CPUs
[    0.032905] smpboot: Max logical packages: 1
[    0.032905] smpboot: Total of 4 processors activated (24744.63 BogoMIPS)
[    0.036152] devtmpfs: initialized
[    0.036152] x86/mm: Memory block size: 128MB
[    0.036331] evm: security.selinux
[    0.036332] evm: security.SMACK64
[    0.036332] evm: security.SMACK64EXEC
[    0.036333] evm: security.SMACK64TRANSMUTE
[    0.036333] evm: security.SMACK64MMAP
[    0.036333] evm: security.apparmor
[    0.036334] evm: security.ima
[    0.036334] evm: security.capability
[    0.036345] PM: Registering ACPI NVS region [mem 0xdd880000-0xde10dfff] (8970240 bytes)
[    0.036345] PM: Registering ACPI NVS region [mem 0xded97000-0xdedd9fff] (274432 bytes)
[    0.036345] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.036345] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.036345] pinctrl core: initialized pinctrl subsystem
[    0.036345] RTC time: 13:59:29, date: 03/12/20
[    0.036345] NET: Registered protocol family 16
[    0.036345] audit: initializing netlink subsys (disabled)
[    0.036345] audit: type=2000 audit(1584021569.036:1): state=initialized audit_enabled=0 res=1
[    0.036345] cpuidle: using governor ladder
[    0.036345] cpuidle: using governor menu
[    0.036345] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[    0.036345] ACPI: bus type PCI registered
[    0.036345] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.036345] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[    0.036345] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[    0.036345] PCI: Using configuration type 1 for base access
[    0.036345] core: PMU erratum BJ122, BV98, HSD29 workaround disabled, HT off
[    0.036903] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.036903] ACPI: Added _OSI(Module Device)
[    0.036903] ACPI: Added _OSI(Processor Device)
[    0.036903] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.036903] ACPI: Added _OSI(Processor Aggregator Device)
[    0.036903] ACPI: Added _OSI(Linux-Dell-Video)
[    0.036903] ACPI: Added _OSI(Linux-Lenovo-NV-HDMI-Audio)
[    0.036903] ACPI: Added _OSI(Linux-HPI-Hybrid-Graphics)
[    0.036903] ACPI: Executed 1 blocks of module-level executable AML code
[    0.040985] ACPI: Dynamic OEM Table Load:
[    0.040985] ACPI: SSDT 0xFFFF9DB8D942E000 00083B (v01 PmRef  Cpu0Cst  00003001 INTL 20051117)
[    0.040985] ACPI: Dynamic OEM Table Load:
[    0.040985] ACPI: SSDT 0xFFFF9DB8D953EC00 000303 (v01 PmRef  ApIst    00003000 INTL 20051117)
[    0.040985] ACPI: Dynamic OEM Table Load:
[    0.040985] ACPI: SSDT 0xFFFF9DB8D978DA00 000119 (v01 PmRef  ApCst    00003000 INTL 20051117)
[    0.041349] ACPI: Interpreter enabled
[    0.041366] ACPI: (supports S0 S3 S4 S5)
[    0.041367] ACPI: Using IOAPIC for interrupt routing
[    0.041391] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.041956] ACPI: Enabled 16 GPEs in block 00 to 3F
[    0.055968] ACPI: Power Resource [FN00] (off)
[    0.056051] ACPI: Power Resource [FN01] (off)
[    0.056132] ACPI: Power Resource [FN02] (off)
[    0.056210] ACPI: Power Resource [FN03] (off)
[    0.056289] ACPI: Power Resource [FN04] (off)
[    0.056926] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[    0.056930] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.057289] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
[    0.057289] acpi PNP0A08:00: FADT indicates ASPM is unsupported, using BIOS configuration
[    0.057853] PCI host bridge to bus 0000:00
[    0.057855] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7 window]
[    0.057856] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    0.057857] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    0.057858] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff window]
[    0.057859] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff window]
[    0.057860] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff window]
[    0.057860] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff window]
[    0.057862] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000e3fff window]
[    0.057863] pci_bus 0000:00: root bus resource [mem 0x000e4000-0x000e7fff window]
[    0.057864] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xfeafffff window]
[    0.057865] pci_bus 0000:00: root bus resource [bus 00-3e]
[    0.057871] pci 0000:00:00.0: [8086:0150] type 00 class 0x060000
[    0.057962] pci 0000:00:01.0: [8086:0151] type 01 class 0x060400
[    0.057992] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.058095] pci 0000:00:16.0: [8086:1c3a] type 00 class 0x078000
[    0.058120] pci 0000:00:16.0: reg 0x10: [mem 0xf720a000-0xf720a00f 64bit]
[    0.058191] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[    0.058275] pci 0000:00:1a.0: [8086:1c2d] type 00 class 0x0c0320
[    0.058297] pci 0000:00:1a.0: reg 0x10: [mem 0xf7208000-0xf72083ff]
[    0.058378] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[    0.058459] pci 0000:00:1b.0: [8086:1c20] type 00 class 0x040300
[    0.058480] pci 0000:00:1b.0: reg 0x10: [mem 0xf7200000-0xf7203fff 64bit]
[    0.058551] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.058636] pci 0000:00:1c.0: [8086:1c10] type 01 class 0x060400
[    0.058719] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.058804] pci 0000:00:1c.2: [8086:1c14] type 01 class 0x060400
[    0.058886] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[    0.058978] pci 0000:00:1d.0: [8086:1c26] type 00 class 0x0c0320
[    0.058999] pci 0000:00:1d.0: reg 0x10: [mem 0xf7207000-0xf72073ff]
[    0.059081] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[    0.059162] pci 0000:00:1f.0: [8086:1c5c] type 00 class 0x060100
[    0.059338] pci 0000:00:1f.2: [8086:1c02] type 00 class 0x010601
[    0.059356] pci 0000:00:1f.2: reg 0x10: [io  0xf070-0xf077]
[    0.059363] pci 0000:00:1f.2: reg 0x14: [io  0xf060-0xf063]
[    0.059371] pci 0000:00:1f.2: reg 0x18: [io  0xf050-0xf057]
[    0.059378] pci 0000:00:1f.2: reg 0x1c: [io  0xf040-0xf043]
[    0.059385] pci 0000:00:1f.2: reg 0x20: [io  0xf020-0xf03f]
[    0.059392] pci 0000:00:1f.2: reg 0x24: [mem 0xf7206000-0xf72067ff]
[    0.059431] pci 0000:00:1f.2: PME# supported from D3hot
[    0.059504] pci 0000:00:1f.3: [8086:1c22] type 00 class 0x0c0500
[    0.059523] pci 0000:00:1f.3: reg 0x10: [mem 0xf7205000-0xf72050ff 64bit]
[    0.059542] pci 0000:00:1f.3: reg 0x20: [io  0xf000-0xf01f]
[    0.059665] pci 0000:01:00.0: [10de:1048] type 00 class 0x030000
[    0.059679] pci 0000:01:00.0: reg 0x10: [mem 0xf6000000-0xf6ffffff]
[    0.059686] pci 0000:01:00.0: reg 0x14: [mem 0xe8000000-0xefffffff 64bit pref]
[    0.059693] pci 0000:01:00.0: reg 0x1c: [mem 0xf0000000-0xf1ffffff 64bit pref]
[    0.059699] pci 0000:01:00.0: reg 0x24: [io  0xe000-0xe07f]
[    0.059704] pci 0000:01:00.0: reg 0x30: [mem 0xf7000000-0xf707ffff pref]
[    0.059708] pci 0000:01:00.0: enabling Extended Tags
[    0.059776] pci 0000:01:00.1: [10de:0e08] type 00 class 0x040300
[    0.059787] pci 0000:01:00.1: reg 0x10: [mem 0xf7080000-0xf7083fff]
[    0.059815] pci 0000:01:00.1: enabling Extended Tags
[    0.068022] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.068025] pci 0000:00:01.0:   bridge window [io  0xe000-0xefff]
[    0.068028] pci 0000:00:01.0:   bridge window [mem 0xf6000000-0xf70fffff]
[    0.068032] pci 0000:00:01.0:   bridge window [mem 0xe8000000-0xf1ffffff 64bit pref]
[    0.068102] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.068175] pci 0000:03:00.0: [10ec:8168] type 00 class 0x020000
[    0.068209] pci 0000:03:00.0: reg 0x10: [io  0xd000-0xd0ff]
[    0.068242] pci 0000:03:00.0: reg 0x18: [mem 0xf7104000-0xf7104fff 64bit pref]
[    0.068263] pci 0000:03:00.0: reg 0x20: [mem 0xf7100000-0xf7103fff 64bit pref]
[    0.068383] pci 0000:03:00.0: supports D1 D2
[    0.068384] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.080029] pci 0000:00:1c.2: PCI bridge to [bus 03]
[    0.080034] pci 0000:00:1c.2:   bridge window [io  0xd000-0xdfff]
[    0.080039] pci 0000:00:1c.2:   bridge window [mem 0xf7100000-0xf71fffff]
[    0.081064] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 *10 12 14 15)
[    0.081129] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 10 12 14 15)
[    0.081192] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 10 12 14 15)
[    0.081254] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 *4 5 6 10 12 14 15)
[    0.081316] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 12 14 15) *0, disabled.
[    0.081379] ACPI: PCI Interrupt Link [LNKF] (IRQs 10 *11)
[    0.081441] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 *10 12 14 15)
[    0.081503] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 *4 5 6 10 12 14 15)
[    0.081933] SCSI subsystem initialized
[    0.081942] libata version 3.00 loaded.
[    0.081942] pci 0000:01:00.0: vgaarb: setting as boot VGA device
[    0.081942] pci 0000:01:00.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[    0.081942] pci 0000:01:00.0: vgaarb: bridge control possible
[    0.081942] vgaarb: loaded
[    0.081942] ACPI: bus type USB registered
[    0.081942] usbcore: registered new interface driver usbfs
[    0.081942] usbcore: registered new interface driver hub
[    0.081942] usbcore: registered new device driver usb
[    0.081942] EDAC MC: Ver: 3.0.0
[    0.081942] PCI: Using ACPI for IRQ routing
[    0.081942] PCI: pci_cache_line_size set to 64 bytes
[    0.081942] e820: reserve RAM buffer [mem 0x0009d800-0x0009ffff]
[    0.081942] e820: reserve RAM buffer [mem 0xdd7cf000-0xdfffffff]
[    0.081942] e820: reserve RAM buffer [mem 0xdf59c000-0xdfffffff]
[    0.081942] e820: reserve RAM buffer [mem 0xdf800000-0xdfffffff]
[    0.081942] e820: reserve RAM buffer [mem 0x11f000000-0x11fffffff]
[    0.081942] NetLabel: Initializing
[    0.081942] NetLabel:  domain hash size = 128
[    0.081942] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    0.081942] NetLabel:  unlabeled traffic allowed by default
[    0.084344] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[    0.084347] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[    0.087369] clocksource: Switched to clocksource hpet
[    0.092680] VFS: Disk quotas dquot_6.6.0
[    0.092694] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.092773] AppArmor: AppArmor Filesystem Enabled
[    0.092798] pnp: PnP ACPI init
[    0.092905] system 00:00: [mem 0xfed40000-0xfed44fff] has been reserved
[    0.092909] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.093017] system 00:01: [io  0x0680-0x069f] has been reserved
[    0.093018] system 00:01: [io  0x1000-0x100f] has been reserved
[    0.093019] system 00:01: [io  0xffff] has been reserved
[    0.093020] system 00:01: [io  0xffff] has been reserved
[    0.093021] system 00:01: [io  0x0400-0x0453] has been reserved
[    0.093022] system 00:01: [io  0x0458-0x047f] has been reserved
[    0.093023] system 00:01: [io  0x0500-0x057f] has been reserved
[    0.093023] system 00:01: [io  0x164e-0x164f] has been reserved
[    0.093026] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.093048] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.093094] system 00:03: [io  0x0454-0x0457] has been reserved
[    0.093097] system 00:03: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[    0.093250] system 00:04: [io  0x0a00-0x0a1f] has been reserved
[    0.093251] system 00:04: [io  0x0a30-0x0a3f] has been reserved
[    0.093252] system 00:04: [io  0x0a20-0x0a2f] has been reserved
[    0.093255] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.093685] pnp 00:05: [dma 0 disabled]
[    0.093723] pnp 00:05: Plug and Play ACPI device, IDs PNP0501 (active)
[    0.094093] pnp 00:06: [dma 0 disabled]
[    0.094215] pnp 00:06: Plug and Play ACPI device, IDs PNP0400 (active)
[    0.094401] system 00:07: [io  0x04d0-0x04d1] has been reserved
[    0.094404] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.094651] system 00:08: [mem 0xfed1c000-0xfed1ffff] has been reserved
[    0.094652] system 00:08: [mem 0xfed10000-0xfed17fff] has been reserved
[    0.094653] system 00:08: [mem 0xfed18000-0xfed18fff] has been reserved
[    0.094654] system 00:08: [mem 0xfed19000-0xfed19fff] has been reserved
[    0.094655] system 00:08: [mem 0xf8000000-0xfbffffff] has been reserved
[    0.094656] system 00:08: [mem 0xfed20000-0xfed3ffff] has been reserved
[    0.094657] system 00:08: [mem 0xfed90000-0xfed93fff] has been reserved
[    0.094658] system 00:08: [mem 0xfed45000-0xfed8ffff] has been reserved
[    0.094659] system 00:08: [mem 0xff000000-0xffffffff] has been reserved
[    0.094661] system 00:08: [mem 0xfee00000-0xfeefffff] could not be reserved
[    0.094662] system 00:08: [mem 0xe0000000-0xe0000fff] has been reserved
[    0.094664] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.094825] pnp: PnP ACPI: found 9 devices
[    0.100794] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    0.100818] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.100820] pci 0000:00:01.0:   bridge window [io  0xe000-0xefff]
[    0.100822] pci 0000:00:01.0:   bridge window [mem 0xf6000000-0xf70fffff]
[    0.100824] pci 0000:00:01.0:   bridge window [mem 0xe8000000-0xf1ffffff 64bit pref]
[    0.100826] pci 0000:00:1c.0: PCI bridge to [bus 02]
[    0.100837] pci 0000:00:1c.2: PCI bridge to [bus 03]
[    0.100839] pci 0000:00:1c.2:   bridge window [io  0xd000-0xdfff]
[    0.100843] pci 0000:00:1c.2:   bridge window [mem 0xf7100000-0xf71fffff]
[    0.100851] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7 window]
[    0.100852] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff window]
[    0.100853] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[    0.100854] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000d3fff window]
[    0.100855] pci_bus 0000:00: resource 8 [mem 0x000d4000-0x000d7fff window]
[    0.100856] pci_bus 0000:00: resource 9 [mem 0x000d8000-0x000dbfff window]
[    0.100856] pci_bus 0000:00: resource 10 [mem 0x000dc000-0x000dffff window]
[    0.100857] pci_bus 0000:00: resource 11 [mem 0x000e0000-0x000e3fff window]
[    0.100858] pci_bus 0000:00: resource 12 [mem 0x000e4000-0x000e7fff window]
[    0.100859] pci_bus 0000:00: resource 13 [mem 0xe0000000-0xfeafffff window]
[    0.100860] pci_bus 0000:01: resource 0 [io  0xe000-0xefff]
[    0.100861] pci_bus 0000:01: resource 1 [mem 0xf6000000-0xf70fffff]
[    0.100862] pci_bus 0000:01: resource 2 [mem 0xe8000000-0xf1ffffff 64bit pref]
[    0.100863] pci_bus 0000:03: resource 0 [io  0xd000-0xdfff]
[    0.100864] pci_bus 0000:03: resource 1 [mem 0xf7100000-0xf71fffff]
[    0.100956] NET: Registered protocol family 2
[    0.101067] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[    0.101126] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    0.101211] TCP: Hash tables configured (established 32768 bind 32768)
[    0.101236] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.101249] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.101285] NET: Registered protocol family 1
[    0.148141] pci 0000:01:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[    0.148150] PCI: CLS mismatch (64 != 32), using 64 bytes
[    0.148180] Unpacking initramfs...
[    0.558824] Freeing initrd memory: 38472K
[    0.558844] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    0.558845] software IO TLB: mapped [mem 0xd97cf000-0xdd7cf000] (64MB)
[    0.559028] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2c95bdc3567, max_idle_ns: 440795309065 ns
[    0.559091] Scanning for low memory corruption every 60 seconds
[    0.559631] Initialise system trusted keyrings
[    0.559639] Key type blacklist registered
[    0.559668] workingset: timestamp_bits=36 max_order=20 bucket_order=0
[    0.560503] zbud: loaded
[    0.560886] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.560984] fuse init (API version 7.26)
[    0.562138] Key type asymmetric registered
[    0.562138] Asymmetric key parser 'x509' registered
[    0.562158] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[    0.562186] io scheduler noop registered
[    0.562187] io scheduler deadline registered
[    0.562204] io scheduler cfq registered (default)
[    0.562750] pcieport 0000:00:01.0: Signaling PME with IRQ 24
[    0.562774] pcieport 0000:00:1c.0: Signaling PME with IRQ 25
[    0.562794] pcieport 0000:00:1c.2: Signaling PME with IRQ 26
[    0.562842] vesafb: mode is 640x480x32, linelength=2560, pages=0
[    0.562842] vesafb: scrolling: redraw
[    0.562843] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[    0.562849] vesafb: framebuffer at 0xf1000000, mapped to 0x        (ptrval), using 1216k, total 1216k
[    0.562916] Console: switching to colour frame buffer device 80x30
[    0.562924] fb0: VESA VGA frame buffer device
[    0.562934] intel_idle: MWAIT substates: 0x1120
[    0.562935] intel_idle: v0.4.1 model 0x3A
[    0.563036] intel_idle: lapic_timer_reliable_states 0xffffffff
[    0.563126] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[    0.563150] ACPI: Power Button [PWRB]
[    0.563178] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[    0.563194] ACPI: Power Button [PWRF]
[    0.563786] (NULL device *): hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().
[    0.563864] thermal LNXTHERM:00: registered as thermal_zone0
[    0.563865] ACPI: Thermal Zone [TZ00] (28 C)
[    0.564142] thermal LNXTHERM:01: registered as thermal_zone1
[    0.564143] ACPI: Thermal Zone [TZ01] (30 C)
[    0.564311] thermal LNXTHERM:02: registered as thermal_zone2
[    0.564311] ACPI: Thermal Zone [THRM] (30 C)
[    0.564411] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[    0.584989] 00:05: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
[    0.586589] Linux agpgart interface v0.103
[    0.587858] loop: module loaded
[    0.587972] libphy: Fixed MDIO Bus: probed
[    0.587973] tun: Universal TUN/TAP device driver, 1.6
[    0.587998] PPP generic driver version 2.4.2
[    0.588042] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.588044] ehci-pci: EHCI PCI platform driver
[    0.588137] ehci-pci 0000:00:1a.0: EHCI Host Controller
[    0.588142] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1
[    0.588153] ehci-pci 0000:00:1a.0: debug port 2
[    0.592058] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[    0.592067] ehci-pci 0000:00:1a.0: irq 16, io mem 0xf7208000
[    0.608053] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[    0.608110] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.608111] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.608112] usb usb1: Product: EHCI Host Controller
[    0.608113] usb usb1: Manufacturer: Linux 4.15.0-88-generic ehci_hcd
[    0.608114] usb usb1: SerialNumber: 0000:00:1a.0
[    0.608263] hub 1-0:1.0: USB hub found
[    0.608269] hub 1-0:1.0: 2 ports detected
[    0.608474] ehci-pci 0000:00:1d.0: EHCI Host Controller
[    0.608478] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    0.608488] ehci-pci 0000:00:1d.0: debug port 2
[    0.612382] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[    0.612389] ehci-pci 0000:00:1d.0: irq 23, io mem 0xf7207000
[    0.628061] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[    0.628121] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    0.628122] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.628123] usb usb2: Product: EHCI Host Controller
[    0.628124] usb usb2: Manufacturer: Linux 4.15.0-88-generic ehci_hcd
[    0.628125] usb usb2: SerialNumber: 0000:00:1d.0
[    0.628270] hub 2-0:1.0: USB hub found
[    0.628276] hub 2-0:1.0: 2 ports detected
[    0.628393] ehci-platform: EHCI generic platform driver
[    0.628399] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.628402] ohci-pci: OHCI PCI platform driver
[    0.628408] ohci-platform: OHCI generic platform driver
[    0.628412] uhci_hcd: USB Universal Host Controller Interface driver
[    0.628445] i8042: PNP: No PS/2 controller found.
[    0.628614] mousedev: PS/2 mouse device common for all mice
[    0.628878] rtc_cmos 00:02: RTC can wake from S4
[    0.629029] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[    0.629054] rtc_cmos 00:02: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[    0.629060] i2c /dev entries driver
[    0.629092] device-mapper: uevent: version 1.0.3
[    0.629164] device-mapper: ioctl: 4.37.0-ioctl (2017-09-20) initialised: dm-devel@redhat.com
[    0.629169] intel_pstate: Intel P-state driver initializing
[    0.629410] ledtrig-cpu: registered to indicate activity on CPUs
[    0.629944] NET: Registered protocol family 10
[    0.633602] Segment Routing with IPv6
[    0.633618] NET: Registered protocol family 17
[    0.633725] Key type dns_resolver registered
[    0.634001] mce: Using 9 MCE banks
[    0.634014] RAS: Correctable Errors collector initialized.
[    0.634038] microcode: sig=0x306a9, pf=0x2, revision=0x21
[    0.634133] microcode: Microcode Update Driver: v2.2.
[    0.634285] registered taskstats version 1
[    0.634292] Loading compiled-in X.509 certificates
[    0.636560] Loaded X.509 cert 'Build time autogenerated kernel key: f0020782f0d3a548186fb3f47aed88387a71e859'
[    0.636577] zswap: loaded using pool lzo/zbud
[    0.639835] Key type big_key registered
[    0.639838] Key type trusted registered
[    0.641577] Key type encrypted registered
[    0.641579] AppArmor: AppArmor sha1 policy hashing enabled
[    0.641581] ima: No TPM chip found, activating TPM-bypass! (rc=-19)
[    0.641584] ima: Allocated hash algorithm: sha1
[    0.641605] evm: HMAC attrs: 0x1
[    0.641781]   Magic number: 12:702:988
[    0.641784] machinecheck machinecheck1: hash matches
[    0.641906] rtc_cmos 00:02: setting system clock to 2020-03-12 13:59:30 UTC (1584021570)
[    0.641982] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    0.641983] EDD information not available.
[    0.643667] Freeing unused kernel image memory: 2428K
[    0.668080] Write protecting the kernel read-only data: 20480k
[    0.668608] Freeing unused kernel image memory: 2008K
[    0.668885] Freeing unused kernel image memory: 1880K
[    0.675646] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    0.675647] x86/mm: Checking user space page tables
[    0.682005] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    0.748141] ahci 0000:00:1f.2: version 3.0
[    0.748341] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 4 ports 3 Gbps 0x3 impl SATA mode
[    0.748343] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part ems apst 
[    0.748478] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    0.748484] r8169 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control
[    0.749230] r8169 0000:03:00.0 eth0: RTL8168f/8111f at 0x        (ptrval), 74:27:ea:52:03:c0, XID 08100800 IRQ 28
[    0.749231] r8169 0000:03:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[    0.760663] scsi host0: ahci
[    0.761216] scsi host1: ahci
[    0.763346] r8169 0000:03:00.0 enp3s0: renamed from eth0
[    0.763513] scsi host2: ahci
[    0.763619] scsi host3: ahci
[    0.763651] ata1: SATA max UDMA/133 abar m2048@0xf7206000 port 0xf7206100 irq 27
[    0.763653] ata2: SATA max UDMA/133 abar m2048@0xf7206000 port 0xf7206180 irq 27
[    0.763654] ata3: DUMMY
[    0.763655] ata4: DUMMY
[    0.944063] usb 1-1: new high-speed USB device number 2 using ehci-pci
[    0.964055] usb 2-1: new high-speed USB device number 2 using ehci-pci
[    1.079042] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.079065] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.080172] ata1.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[    1.080175] ata1.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[    1.080177] ata1.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[    1.081105] ata1.00: ATA-8: WDC WD10EZEX-22RKKA0, 80.00A80, max UDMA/133
[    1.081108] ata1.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    1.082220] ata1.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[    1.082223] ata1.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[    1.082225] ata1.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[    1.082285] ata2.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[    1.082286] ata2.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[    1.082287] ata2.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[    1.082590] ata2.00: ATAPI: ATAPI   DVD A  DH16ACSH, JA11, max UDMA/100
[    1.083165] ata1.00: configured for UDMA/133
[    1.083426] scsi 0:0:0:0: Direct-Access     ATA      WDC WD10EZEX-22R 0A80 PQ: 0 ANSI: 5
[    1.083784] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[    1.083785] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    1.083793] sd 0:0:0:0: [sda] Write Protect is off
[    1.083794] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.083804] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.083967] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.084253] ata2.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[    1.084256] ata2.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[    1.084258] ata2.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[    1.084526] ata2.00: configured for UDMA/100
[    1.086675] scsi 1:0:0:0: CD-ROM            ATAPI    DVD A  DH16ACSH  JA11 PQ: 0 ANSI: 5
[    1.100719] usb 1-1: New USB device found, idVendor=8087, idProduct=0024
[    1.100721] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.101049] hub 1-1:1.0: USB hub found
[    1.101127] hub 1-1:1.0: 4 ports detected
[    1.111822]  sda: sda1 sda2 sda3 < sda5 sda6 >
[    1.112205] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.120400] usb 2-1: New USB device found, idVendor=8087, idProduct=0024
[    1.120403] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.120684] hub 2-1:1.0: USB hub found
[    1.120729] hub 2-1:1.0: 6 ports detected
[    1.165480] sr 1:0:0:0: [sr0] scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[    1.165483] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.165669] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    1.165740] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    1.388031] usb 1-1.3: new low-speed USB device number 3 using ehci-pci
[    1.408044] usb 2-1.4: new high-speed USB device number 3 using ehci-pci
[    1.501087] usb 1-1.3: New USB device found, idVendor=0461, idProduct=4e2b
[    1.501088] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    1.501089] usb 1-1.3: Product: USB Optical Mouse
[    1.501090] usb 1-1.3: Manufacturer: PixArt
[    1.504370] hidraw: raw HID events driver (C) Jiri Kosina
[    1.507962] usbcore: registered new interface driver usbhid
[    1.507962] usbhid: USB HID core driver
[    1.509774] input: PixArt USB Optical Mouse as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.0/0003:0461:4E2B.0001/input/input2
[    1.509991] hid-generic 0003:0461:4E2B.0001: input,hidraw0: USB HID v1.11 Mouse [PixArt USB Optical Mouse] on usb-0000:00:1a.0-1.3/input0
[    1.536133] usb 2-1.4: New USB device found, idVendor=054c, idProduct=05bf
[    1.536136] usb 2-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    1.536137] usb 2-1.4: Product: Hard Drive
[    1.536139] usb 2-1.4: Manufacturer: Sony
[    1.536140] usb 2-1.4: SerialNumber: 2071170203FD
[    1.536617] random: fast init done
[    1.536735] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[    1.536752] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[    1.536765] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[    1.539338] usb-storage 2-1.4:1.0: USB Mass Storage device detected
[    1.539582] scsi host4: usb-storage 2-1.4:1.0
[    1.539637] usbcore: registered new interface driver usb-storage
[    1.540760] usbcore: registered new interface driver uas
[    1.584030] usb 1-1.4: new low-speed USB device number 4 using ehci-pci
[    1.616036] usb 2-1.6: new high-speed USB device number 4 using ehci-pci
[    1.701837] usb 1-1.4: New USB device found, idVendor=04ca, idProduct=0050
[    1.701838] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    1.701839] usb 1-1.4: Product: USB Multimedia Keyboard
[    1.701840] usb 1-1.4: Manufacturer: Lite-On Technology Corp.
[    1.706297] input: Lite-On Technology Corp. USB Multimedia Keyboard as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.4/1-1.4:1.0/0003:04CA:0050.0002/input/input3
[    1.724859] usb 2-1.6: New USB device found, idVendor=0bda, idProduct=0129
[    1.724862] usb 2-1.6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    1.724863] usb 2-1.6: Product: USB2.0-CRW
[    1.724865] usb 2-1.6: Manufacturer: Generic
[    1.724866] usb 2-1.6: SerialNumber: 20100201396000000
[    1.729457] usbcore: registered new interface driver rtsx_usb
[    1.764281] hid-generic 0003:04CA:0050.0002: input,hidraw1: USB HID v1.10 Keyboard [Lite-On Technology Corp. USB Multimedia Keyboard] on usb-0000:00:1a.0-1.4/input0
[    1.767280] input: Lite-On Technology Corp. USB Multimedia Keyboard as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.4/1-1.4:1.1/0003:04CA:0050.0003/input/input4
[    1.824200] hid-generic 0003:04CA:0050.0003: input,hidraw2: USB HID v1.10 Device [Lite-On Technology Corp. USB Multimedia Keyboard] on usb-0000:00:1a.0-1.4/input1
[    1.975533] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null)
[    3.364290] ip_tables: (C) 2000-2006 Netfilter Core Team
[    3.434350] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[    3.452170] systemd[1]: Detected architecture x86-64.
[    3.465631] systemd[1]: Set hostname to <pierre-Aspire-MC605>.
[    3.565173] random: crng init done
[    3.565174] random: 7 urandom warning(s) missed due to ratelimiting
[    4.701436] scsi 4:0:0:0: Direct-Access     Sony     Hard Drive            PQ: 0 ANSI: 0
[    4.701783] sd 4:0:0:0: Attached scsi generic sg2 type 0
[    4.702667] sd 4:0:0:0: [sdb] 976773164 512-byte logical blocks: (500 GB/466 GiB)
[    4.703852] sd 4:0:0:0: [sdb] Write Protect is off
[    4.703855] sd 4:0:0:0: [sdb] Mode Sense: 03 00 00 00
[    4.705032] sd 4:0:0:0: [sdb] No Caching mode page found
[    4.705035] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[    4.733644]  sdb:
[    4.736721] sd 4:0:0:0: [sdb] Attached SCSI disk
[    7.528624] systemd[1]: Created slice User and Session Slice.
[    7.528679] systemd[1]: Reached target User and Group Name Lookups.
[    7.528730] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    7.528887] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    7.529020] systemd[1]: Created slice System Slice.
[    7.529099] systemd[1]: Listening on Journal Socket (/dev/log).
[    7.529122] systemd[1]: Reached target Slices.
[    7.903425] EXT4-fs (sda6): re-mounted. Opts: errors=remount-ro
[   10.350422] systemd[1]: Started Create list of required static device nodes for the current kernel.
[   10.351197] systemd[1]: Starting Create Static Device Nodes in /dev...
[   10.732592] systemd[1]: Started Load/Save Random Seed.
[   15.644615] lp: driver loaded but no devices found
[   17.296947] systemd[1]: Started udev Coldplug all Devices.
[   17.360125] systemd[1]: Started Journal Service.
[   17.399897] systemd-journald[288]: Received request to flush runtime journal from PID 1
[   17.503952] ppdev: user-space parallel port driver
[   17.604091] parport_pc 00:06: reported by Plug and Play ACPI
[   17.604169] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[   17.700164] lp0: using parport0 (interrupt-driven).
[   22.064469] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   22.111019] ipmi message handler version 39.2
[   22.149697] audit: type=1400 audit(1584021592.004:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/lightdm/lightdm-guest-session" pid=502 comm="apparmor_parser"
[   22.149700] audit: type=1400 audit(1584021592.004:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/lightdm/lightdm-guest-session//chromium" pid=502 comm="apparmor_parser"
[   22.172335] ACPI Warning: SystemIO range 0x0000000000000428-0x000000000000042F conflicts with OpRegion 0x0000000000000400-0x000000000000047F (\PMIO) (20170831/utaddress-247)
[   22.172339] ACPI Warning: SystemIO range 0x0000000000000428-0x000000000000042F conflicts with OpRegion 0x0000000000000400-0x000000000000047F (\PMIO) (20170831/utaddress-247)
[   22.172342] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   22.172353] ACPI Warning: SystemIO range 0x0000000000000540-0x000000000000054F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20170831/utaddress-247)
[   22.172356] ACPI Warning: SystemIO range 0x0000000000000540-0x000000000000054F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20170831/utaddress-247)
[   22.172358] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   22.172358] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20170831/utaddress-247)
[   22.172360] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20170831/utaddress-247)
[   22.172362] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   22.172363] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20170831/utaddress-247)
[   22.172364] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20170831/utaddress-247)
[   22.172366] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   22.172367] lpc_ich: Resource conflict(s) found affecting gpio_ich
[   22.208778] ipmi device interface
[   22.240306] RAPL PMU: API unit is 2^-32 Joules, 3 fixed counters, 163840 ms ovfl timer
[   22.240308] RAPL PMU: hw unit of domain pp0-core 2^-16 Joules
[   22.240308] RAPL PMU: hw unit of domain package 2^-16 Joules
[   22.240309] RAPL PMU: hw unit of domain pp1-gpu 2^-16 Joules
[   22.242208] audit: type=1400 audit(1584021592.096:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/snap/core/4917/usr/lib/snapd/snap-confine" pid=504 comm="apparmor_parser"
[   22.242210] audit: type=1400 audit(1584021592.096:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/snap/core/4917/usr/lib/snapd/snap-confine//mount-namespace-capture-helper" pid=504 comm="apparmor_parser"
[   22.243553] audit: type=1400 audit(1584021592.096:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=512 comm="apparmor_parser"
[   22.243555] audit: type=1400 audit(1584021592.096:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=512 comm="apparmor_parser"
[   22.243556] audit: type=1400 audit(1584021592.096:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=512 comm="apparmor_parser"
[   22.244558] audit: type=1400 audit(1584021592.100:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-oopslash" pid=513 comm="apparmor_parser"
[   22.266486] audit: type=1400 audit(1584021592.120:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/sbin/dhclient" pid=503 comm="apparmor_parser"
[   22.266489] audit: type=1400 audit(1584021592.120:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=503 comm="apparmor_parser"
[   22.271234] intel_rapl: Found RAPL domain package
[   22.271235] intel_rapl: Found RAPL domain core
[   22.271238] intel_rapl: RAPL package 0 domain package locked by BIOS
[   24.291332] nvidia: loading out-of-tree module taints kernel.
[   24.291340] nvidia: module license 'NVIDIA' taints kernel.
[   24.291340] Disabling lock debugging due to kernel taint
[   24.296697] nvidia: module verification failed: signature and/or required key missing - tainting kernel
[   24.302390] nvidia-nvlink: Nvlink Core is being initialized, major device number 241
[   24.302684] nvidia 0000:01:00.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=none:owns=io+mem
[   24.302755] NVRM: loading NVIDIA UNIX x86_64 Kernel Module  390.116  Sun Jan 27 07:21:36 PST 2019 (using threaded interrupts)
[   24.595779] nvidia-modeset: Loading NVIDIA Kernel Mode Setting Driver for UNIX platforms  390.116  Sun Jan 27 06:30:32 PST 2019
[   24.596489] [drm] [nvidia-drm] [GPU ID 0x00000100] Loading driver
[   24.596490] [drm] Initialized nvidia-drm 0.0.0 20160202 for 0000:01:00.0 on minor 0
[   24.602187] nvidia-uvm: Loaded the UVM driver in 8 mode, major device number 240
[   24.619225] snd_hda_intel 0000:01:00.1: Disabling MSI
[   24.619229] snd_hda_intel 0000:01:00.1: Handle vga_switcheroo audio client
[   24.630795] snd_hda_codec_realtek hdaudioC0D0: ALC662 rev3: SKU not ready 0x411111f0
[   24.631168] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC662 rev3: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:line
[   24.631169] snd_hda_codec_realtek hdaudioC0D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   24.631170] snd_hda_codec_realtek hdaudioC0D0:    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[   24.631171] snd_hda_codec_realtek hdaudioC0D0:    mono: mono_out=0x0
[   24.631171] snd_hda_codec_realtek hdaudioC0D0:    inputs:
[   24.631173] snd_hda_codec_realtek hdaudioC0D0:      Front Mic=0x19
[   24.631174] snd_hda_codec_realtek hdaudioC0D0:      Rear Mic=0x18
[   24.631174] snd_hda_codec_realtek hdaudioC0D0:      Line=0x1a
[   24.640143] input: HDA Intel PCH Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input5
[   24.640183] input: HDA Intel PCH Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6
[   24.640220] input: HDA Intel PCH Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[   24.640255] input: HDA Intel PCH Line Out as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[   24.640292] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[   24.905404] resource sanity check: requesting [mem 0x000e0000-0x000fffff], which spans more than PCI Bus 0000:00 [mem 0x000e0000-0x000e3fff window]
[   24.905581] caller os_map_kernel_space.part.8+0x10b/0x150 [nvidia] mapping multiple BARs
[   25.191054] resource sanity check: requesting [mem 0x000c0000-0x000fffff], which spans more than PCI Bus 0000:00 [mem 0x000d0000-0x000d3fff window]
[   25.191239] caller os_map_kernel_space.part.8+0x10b/0x150 [nvidia] mapping multiple BARs
[   25.212404] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input10
[   25.212442] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input11
[   28.249299] Adding 4143100k swap on /dev/sda5.  Priority:-2 extents:1 across:4143100k FS
[   37.988059] IPv6: ADDRCONF(NETDEV_UP): enp3s0: link is not ready
[   38.306354] r8169 0000:03:00.0 enp3s0: link down
[   38.306454] IPv6: ADDRCONF(NETDEV_UP): enp3s0: link is not ready
[   38.307154] r8169 0000:03:00.0 enp3s0: link down
[   39.861842] r8169 0000:03:00.0 enp3s0: link up
[   39.861851] IPv6: ADDRCONF(NETDEV_CHANGE): enp3s0: link becomes ready
[   42.428593] show_signal_msg: 44 callbacks suppressed
[   42.428595] server[1230]: segfault at 1a0 ip 00007f56d2c77ab0 sp 00007f56ce9bfc28 error 4 in libudev.so.1.6.9[7f56d2c74000+1d000]
[   42.428627] audit: type=1326 audit(1584021612.284:56): auid=4294967295 uid=0 gid=0 ses=4294967295 pid=1054 comm="server" exe="/snap/hplip-printer-application/3/bin/server" sig=0 arch=c000003e syscall=41 compat=0 ip=0x7f56d29a5ec7 code=0x50000
[   43.679841] server[1285]: segfault at 1a0 ip 00007f206982fab0 sp 00007f2065577c28 error 4 in libudev.so.1.6.9[7f206982c000+1d000]
[   43.679850] audit: type=1326 audit(1584021613.532:57): auid=4294967295 uid=0 gid=0 ses=4294967295 pid=1258 comm="server" exe="/snap/hplip-printer-application/3/bin/server" sig=0 arch=c000003e syscall=41 compat=0 ip=0x7f206955dec7 code=0x50000
[   44.097935] server[1376]: segfault at 1a0 ip 00007f5cf9e84ab0 sp 00007f5cf5bccc28 error 4 in libudev.so.1.6.9[7f5cf9e81000+1d000]
[   44.097947] audit: type=1326 audit(1584021613.952:58): auid=4294967295 uid=0 gid=0 ses=4294967295 pid=1333 comm="server" exe="/snap/hplip-printer-application/3/bin/server" sig=0 arch=c000003e syscall=41 compat=0 ip=0x7f5cf9bb2ec7 code=0x50000
[   44.628033] audit: type=1326 audit(1584021614.480:59): auid=4294967295 uid=0 gid=0 ses=4294967295 pid=1383 comm="server" exe="/snap/hplip-printer-application/3/bin/server" sig=0 arch=c000003e syscall=41 compat=0 ip=0x7f44d1b76ec7 code=0x50000
[   44.628298] server[1410]: segfault at 1a0 ip 00007f44d1e48ab0 sp 00007f44cdb90c28 error 4 in libudev.so.1.6.9[7f44d1e45000+1d000]
[   45.146896] server[1463]: segfault at 1a0 ip 00007fb2629f2ab0 sp 00007fb25e73ac28 error 4 in libudev.so.1.6.9[7fb2629ef000+1d000]
[   45.146908] audit: type=1326 audit(1584021615.000:60): auid=4294967295 uid=0 gid=0 ses=4294967295 pid=1436 comm="server" exe="/snap/hplip-printer-application/3/bin/server" sig=0 arch=c000003e syscall=41 compat=0 ip=0x7fb262720ec7 code=0x50000
[   47.103410] resource sanity check: requesting [mem 0x000c0000-0x000fffff], which spans more than PCI Bus 0000:00 [mem 0x000d0000-0x000d3fff window]
[   47.103602] caller os_map_kernel_space.part.8+0x10b/0x150 [nvidia] mapping multiple BARs
[   48.634400] audit: type=1400 audit(1584021618.488:61): apparmor="DENIED" operation="open" profile="/usr/bin/freshclam" name="/etc/ssl/openssl.cnf" pid=1194 comm="freshclam" requested_mask="r" denied_mask="r" fsuid=127 ouid=0
[   60.570106] audit: type=1400 audit(1584018029.531:62): apparmor="DENIED" operation="mknod" profile="/usr/share/hplip/systray.py" name="/var/crash/_usr_share_hplip_systray.py.1000.crash" pid=3015 comm="hp-systray" requested_mask="c" denied_mask="c" fsuid=1000 ouid=1000
[  517.230464] audit: type=1400 audit(1584018486.190:63): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/usr/share/nvidia/nvidia-application-profiles-390.116-rc" pid=5063 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[  517.237938] audit: type=1400 audit(1584018486.198:64): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/usr/share/nvidia/nvidia-application-profiles-390.116-rc" pid=5063 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[  517.245910] audit: type=1400 audit(1584018486.206:65): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/modules" pid=5063 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[  517.245986] audit: type=1400 audit(1584018486.206:66): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/driver/nvidia/params" pid=5063 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[  517.246001] audit: type=1400 audit(1584018486.206:67): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/dev/nvidiactl" pid=5063 comm="soffice.bin" requested_mask="wr" denied_mask="wr" fsuid=1000 ouid=0
[  517.246023] audit: type=1400 audit(1584018486.206:68): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/sys/devices/system/memory/block_size_bytes" pid=5063 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[  517.246114] audit: type=1400 audit(1584018486.206:69): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/modules" pid=5063 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[  517.246143] audit: type=1400 audit(1584018486.206:70): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/driver/nvidia/params" pid=5063 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[  517.246165] audit: type=1400 audit(1584018486.206:71): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/dev/nvidia-modeset" pid=5063 comm="soffice.bin" requested_mask="wr" denied_mask="wr" fsuid=1000 ouid=0
[  517.246218] audit: type=1400 audit(1584018486.206:72): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/driver/nvidia/params" pid=5063 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[  556.848549] kauditd_printk_skb: 59 callbacks suppressed
[  556.848550] audit: type=1400 audit(1584018525.810:132): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/home/pierre/.thunderbird/profiles.ini" pid=5016 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=1000
[  556.934624] audit: type=1400 audit(1584018525.894:133): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/home/pierre/.thunderbird/79jkduks.default/secmod.db" pid=5016 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=1000
[  556.982919] audit: type=1400 audit(1584018525.942:134): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/home/pierre/.thunderbird/79jkduks.default/cert8.db" pid=5016 comm="soffice.bin" requested_mask="wr" denied_mask="wr" fsuid=1000 ouid=1000
[  556.983330] audit: type=1400 audit(1584018525.942:135): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/home/pierre/.thunderbird/79jkduks.default/key3.db" pid=5016 comm="soffice.bin" requested_mask="wr" denied_mask="wr" fsuid=1000 ouid=1000
[ 1943.332059] usb 1-1.1: new high-speed USB device number 5 using ehci-pci
[ 1943.440888] usb 1-1.1: New USB device found, idVendor=03f0, idProduct=df11
[ 1943.440891] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1943.440893] usb 1-1.1: Product: DeskJet 1110 series
[ 1943.440895] usb 1-1.1: Manufacturer: HP
[ 1943.440896] usb 1-1.1: SerialNumber: CN6BF280VB065R
[ 1943.791956] usblp 1-1.1:1.0: usblp0: USB Bidirectional printer dev 5 if 0 alt 0 proto 2 vid 0x03F0 pid 0xDF11
[ 1943.791988] usbcore: registered new interface driver usblp
[ 1949.157526] usblp0: removed
[ 1949.161117] usblp 1-1.1:1.0: usblp0: USB Bidirectional printer dev 5 if 0 alt 0 proto 2 vid 0x03F0 pid 0xDF11
[ 1985.528898] audit: type=1400 audit(1584019954.489:136): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/usr/share/nvidia/nvidia-application-profiles-390.116-rc" pid=5953 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 1985.535497] audit: type=1400 audit(1584019954.493:137): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/usr/share/nvidia/nvidia-application-profiles-390.116-rc" pid=5953 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 1985.544197] audit: type=1400 audit(1584019954.505:138): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/modules" pid=5953 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 1985.544379] audit: type=1400 audit(1584019954.505:139): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/driver/nvidia/params" pid=5953 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 1985.544389] audit: type=1400 audit(1584019954.505:140): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/dev/nvidiactl" pid=5953 comm="soffice.bin" requested_mask="wr" denied_mask="wr" fsuid=1000 ouid=0
[ 1985.544391] audit: type=1400 audit(1584019954.505:141): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/sys/devices/system/memory/block_size_bytes" pid=5953 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 1985.544415] audit: type=1400 audit(1584019954.505:142): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/modules" pid=5953 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 1985.544442] audit: type=1400 audit(1584019954.505:143): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/driver/nvidia/params" pid=5953 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 1985.544464] audit: type=1400 audit(1584019954.505:144): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/dev/nvidia-modeset" pid=5953 comm="soffice.bin" requested_mask="wr" denied_mask="wr" fsuid=1000 ouid=0
[ 1985.544510] audit: type=1400 audit(1584019954.505:145): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/driver/nvidia/params" pid=5953 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 2137.797721] usblp0: removed
[ 2576.217815] kauditd_printk_skb: 59 callbacks suppressed
[ 2576.217825] audit: type=1400 audit(1584020545.176:205): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/usr/share/nvidia/nvidia-application-profiles-390.116-rc" pid=6115 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 2576.331433] audit: type=1400 audit(1584020545.288:206): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/usr/share/nvidia/nvidia-application-profiles-390.116-rc" pid=6115 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 2576.340305] audit: type=1400 audit(1584020545.300:207): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/modules" pid=6115 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 2576.340335] audit: type=1400 audit(1584020545.300:208): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/driver/nvidia/params" pid=6115 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 2576.340360] audit: type=1400 audit(1584020545.300:209): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/dev/nvidiactl" pid=6115 comm="soffice.bin" requested_mask="wr" denied_mask="wr" fsuid=1000 ouid=0
[ 2576.340383] audit: type=1400 audit(1584020545.300:210): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/sys/devices/system/memory/block_size_bytes" pid=6115 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 2576.340478] audit: type=1400 audit(1584020545.300:211): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/modules" pid=6115 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 2576.340509] audit: type=1400 audit(1584020545.300:212): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/driver/nvidia/params" pid=6115 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 2576.340527] audit: type=1400 audit(1584020545.300:213): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/dev/nvidia-modeset" pid=6115 comm="soffice.bin" requested_mask="wr" denied_mask="wr" fsuid=1000 ouid=0
[ 2576.340591] audit: type=1400 audit(1584020545.300:214): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/driver/nvidia/params" pid=6115 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 3437.999628]  sdb: sdb1 < >
[ 3656.297080] kauditd_printk_skb: 59 callbacks suppressed
[ 3656.297089] audit: type=1400 audit(1584021625.257:274): apparmor="DENIED" operation="open" profile="/usr/bin/freshclam" name="/etc/ssl/openssl.cnf" pid=1194 comm="freshclam" requested_mask="r" denied_mask="r" fsuid=127 ouid=0
[ 6727.880671] audit: type=1400 audit(1584024696.843:275): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/usr/share/nvidia/nvidia-application-profiles-390.116-rc" pid=6987 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 6727.888775] audit: type=1400 audit(1584024696.851:276): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/usr/share/nvidia/nvidia-application-profiles-390.116-rc" pid=6987 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 6727.899164] audit: type=1400 audit(1584024696.859:277): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/modules" pid=6987 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 6727.899196] audit: type=1400 audit(1584024696.859:278): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/driver/nvidia/params" pid=6987 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 6727.899247] audit: type=1400 audit(1584024696.859:279): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/dev/nvidiactl" pid=6987 comm="soffice.bin" requested_mask="wr" denied_mask="wr" fsuid=1000 ouid=0
[ 6727.899257] audit: type=1400 audit(1584024696.859:280): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/sys/devices/system/memory/block_size_bytes" pid=6987 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 6727.899377] audit: type=1400 audit(1584024696.859:281): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/modules" pid=6987 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 6727.899405] audit: type=1400 audit(1584024696.859:282): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/driver/nvidia/params" pid=6987 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 6727.899433] audit: type=1400 audit(1584024696.859:283): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/dev/nvidia-modeset" pid=6987 comm="soffice.bin" requested_mask="wr" denied_mask="wr" fsuid=1000 ouid=0
[ 6727.899483] audit: type=1400 audit(1584024696.859:284): apparmor="ALLOWED" operation="open" profile="libreoffice-soffice" name="/proc/driver/nvidia/params" pid=6987 comm="soffice.bin" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0

Je pense qu'il y a une indication utile que vers le dernier quart du retour

Watts · Le 12/03/2020, à 17:10

Ton disque n'est pas sdb? Avec une seule partition nommée sdb1?

MicP · Le 12/03/2020, à 17:11

Bonjour

…Disque dur externe ne monte pas…

De toutes façons, tu ne pourras jamais monter un disque, ni même une partition,
mais seulement un système de gestion de fichiers.

=======

…début de re-initialisation du disque externe,…

Je ne sais pas ce qu'est la "re-initialisation du disque externe"
Pourrais-tu détailler la façon dont tu as procédé pour qu'on puisse savoir précisément ce qui a été tenté.

…annulée rapidement dès que je me suis rendu compte de l'erreur…

le moment où tu t'en es rendu compte importe peu,
ce qui compte surtout c'est de savoir à quel moment de cette "re-initialisation du disque externe" tu as annulé l'opération,
et ce que tu as fait précisément pour annuler cette opération.

=======
Il faudrait aussi savoir ce qui a été fait après,
car c'est vraiment bizarre de ne trouver qu'une seule partition (de type étendue),
(mais ça pourrait s'expliquer selon ce que veut dire "re-initialisation du disque externe")

Dernière modification par MicP (Le 12/03/2020, à 17:12)

Pedro31077 · Le 12/03/2020, à 17:23

C'est relativement simple : je voulais reformater un cdrw, la tête un peu dans le seau, et j'ai dû cliquer par mégarde sur l'icône du DDExterne. Ca m'a inconsciemment ramené à la réalité et j'ai arrêté la manip aussitôt.

MicP · Le 12/03/2020, à 17:32

Merci beaucoup, c'est déjà beaucoup plus précis

Ça nous informe qu'une tentative de création d'un système de gestion de fichiers sur le disque lui même (et pas une de ses partitions) aurait été démarrée et aussitôt après, arrêtée.

Quel est le programme qui a servi à lancer cette opération de formatage ?
Comment as-tu procédé pour "arrêté la manip aussitôt." ? (débrancher le disque, la prise de courant, cliquer quelque part sur un des boutons de l'interface du programme, et lequel…)

Pedro31077 · Le 12/03/2020, à 17:45

Comme je le racontais un peu plus haut, j'ai utilisé gnome-disk-utility 3.28.3

Pedro31077 · Le 13/03/2020, à 09:10

Et, pour arrêter la manip, j'ai simplement cliqué sur le bouton "annuler", dans l'appli

MicP · Le 13/03/2020, à 10:24

Je ne connais pas gnome-disk, ou plutôt, je ne l'utilise jamais
mais je pense que, vu le retour de la commande fdisk,
il a sans doute modifié la table des partitions
et peut-être même altéré les données de la première partition du disque.

Je pense qu'il faudrait tenter d'utiliser un programme de récupération des données sur le disque,
peut-être avec testdisk et photorec

Mais il y a sûrement des personnes plus qualifiées que moi pour t'aider à récupérer ces données,
je préfère éviter de prendre le risque de te faire perdre ce qui pourrait être encore récupérable.

Dernière modification par MicP (Le 13/03/2020, à 19:55)

Pedro31077 · Le 13/03/2020, à 11:46

Je n'ai pas de données à récupérer sur le disque dur externe, il ne me sert qu'à doubler mes sauvegardes, donc pas de pb de ce point de vue.
Par contre, j'aimerais bien pouvoir le réutiliser, d'où la nécessité de pouvoir le monter.

Merci quand même de t'être penché sur le problème

MicP · Le 13/03/2020, à 17:22

…Je n'ai pas de données à récupérer sur le disque dur externe,…

Dans ce cas là, s'il n'y a rien à récupérer sur ce disque,
il suffirait d'y créer une table des partitions
puis d'y créer une partition
et de formater cette partition avec le type de système de gestion de fichiers de ton choix.

=======
Si tu comptes utiliser ce disque pour y lire et écrire seulement depuis Linux
tu pourrais formater sa partition avec le type de système de gestion de fichiers ext4
il te suffira, après formatage, d'adapter les propriétés du système de gestion de fichiers
pour que ton compte utilisateur ait le droit d'y lire et écrire.

Mais je suis peut-être allé un peu vite et trop loin dans mes suppositions
et c'est peut-être tout autre chose que tu voudrais faire avec ce disque.

=======

… il ne me sert qu'à doubler mes sauvegardes, …

Est-ce que ces sauvegardes ne sont que des copies de fichiers qui proviennent du système Linux exclusivement ?
Ou bien est-ce que ces sauvegardes sont aussi des copies de fichiers effectuées depuis le système Windows ?

Dernière modification par MicP (Le 14/03/2020, à 18:13)

Pedro31077 · Le 13/03/2020, à 18:40

Tu as bien deviné. Je suis en Dual-boot, principalement Ubuntu, avec Windows 7. Et j'utilise le DDExt comme plate forme de stockage commune.
Mais comment créer un système de gestion de fichiers ext4 ?

MicP · Le 13/03/2020, à 19:43

Comme tu vas utiliser ce disque pour échanger des fichiers entre les deux systèmes (Linux Windows)
et étant donné que contrairement à Linux, Windows ne sait lire que ses propres systèmes de fichiers,
il vaudra mieux que tu créés et formates la partition de ce disque depuis le système Windows.

Il y a déjà sur ce disque une partition étendue,
mais comme je pense que tu ne comptes créer qu'une seule partition sur le disque,
autant supprimer cette partition de type étendue et créer une nouvelle partition de type primaire
qui occupera tout l'espace disponible sur le disque
et la formater avec ce que préférera Windows comme format de système de gestion de fichiers. (NTFS par exemple)

=======
Au moment du formatage (ou après), il vaudra mieux que tu donnes une Étiquette (LABEL) au système de fichiers,
comme par exemple : DDExt ou autre nom qui te permettra de savoir de quoi il s'agit
et qui sera plus facilement reconnaissable que l'UUID du système de gestion de fichiers
qui serait utilisé comme nom de point de montage si le système de gestion de fichiers n'avait pas de LABEL

Ce qui fait qu'une fois monté depuis ton compte utilisateur pierre
le système de fichiers du disque externe sera monté sur /media/pierre/DDExt/

=======
Quand tu comptera arrêter Windows, il te faudra faire attention à bien "éjecter" logiciellement ce disque externe
par une option du genre "Retirer le périphérique en toute sécurité et éjecter le média"
sinon, le système de gestion fichiers du disque externe pourrait ne pas être accessible depuis Linux.

Dernière modification par MicP (Le 14/03/2020, à 00:31)

Pedro31077 · Le 14/03/2020, à 16:52

Merci MicP.
J'ai suivi tes conseils et ça marche, mon DDext ne me boude plus. Je faisais l'erreur de vouloir traiter le problème sous Ubuntu alors qu'il suffisait de le traiter sous W7 (comme quoi, windows peut servir à quelque chose)

Bon WE

moko138 · Le 14/03/2020, à 17:39

Il suffit de bien lire : tout était visible dès le #1 :

fdisk -l 
(...)
Disque /dev/sdb : 465,8 GiB, 500107859968 octets, 976773164 secteurs
Unités : secteur de 1 × 512 = 512 octets
Taille de secteur (logique / physique) : 512 octets / 512 octets
taille d'E/S (minimale / optimale) : 512 octets / 512 octets
Type d'étiquette de disque : dos
Identifiant de disque : 0xa13c88e4

Périphérique Amorçage Début       Fin  Secteurs Taille Id Type
/dev/sdb1              2048 976773119 976771072 465,8G  5 Étendue

Disque /dev/loop8 (...)

C'est-à dire que le disque était toujours visible,
qu'il comportait une table de partitions de type dos
et une unique partition étendue (un conteneur)
mais vide (aucun système de fichiers).

En #3, confirmation :

[ 3437.999628]  sdb: sdb1 < >

.
N'importe quel système d'exploitation permet d'y remédier.

Mais, comme l'a bien dit MicP, aucun système d'exploitation ne peut monter une absence de système de fichiers (FS). Pour une raison très simple :

man mount | head
(...)
NOM
       mount - Monter un système de fichiers

.

= =

Et puisque tu lui as mis un FS de windows (un NTFS si tu as suivi le conseil de MicP)), assure-lui une maintenance hebdomadaire ou décadaire depuis windows.

Coeur Noir · Le 03/04/2021, à 00:09

Désolé de déterrer ce topic, je viens de cette discussion → https://forum.ubuntu-fr.org/viewtopic.php?id=2063245 → et ce sont les erreurs dans le dmesg ( là-bas ) qui m'ont amené ici, car il y a les mêmes erreurs dans le dmesg ici au #5 :

[   42.428595] server[1230]: segfault at 1a0 ip 00007f56d2c77ab0 sp 00007f56ce9bfc28 error 4 in libudev.so.1.6.9[7f56d2c74000+1d000]
[   43.679841] server[1285]: segfault at 1a0 ip 00007f206982fab0 sp 00007f2065577c28 error 4 in libudev.so.1.6.9[7f206982c000+1d000]
[   44.097935] server[1376]: segfault at 1a0 ip 00007f5cf9e84ab0 sp 00007f5cf5bccc28 error 4 in libudev.so.1.6.9[7f5cf9e81000+1d000]
[   44.628298] server[1410]: segfault at 1a0 ip 00007f44d1e48ab0 sp 00007f44cdb90c28 error 4 in libudev.so.1.6.9[7f44d1e45000+1d000]
[   45.146896] server[1463]: segfault at 1a0 ip 00007fb2629f2ab0 sp 00007fb25e73ac28 error 4 in libudev.so.1.6.9[7fb2629ef000+1d000]

Ma question est donc : ces erreurs sont-elles ( ici ) la conséquence du fait qu'il n'y avait aucun système de fichiers sur le DD ?
Vu le rôle de libudev et la mention segfault j'aurais craint qu'il y ait quelque chose de plus « sérieux »…

Ubuntu-fr

Navigation

Liens de recherche

Annonce

#1 Le 12/03/2020, à 15:43

Disque dur externe ne monte pas

#2 Le 12/03/2020, à 16:06

Re : Disque dur externe ne monte pas

#3 Le 12/03/2020, à 16:21

Re : Disque dur externe ne monte pas

#4 Le 12/03/2020, à 16:34

Re : Disque dur externe ne monte pas

#5 Le 12/03/2020, à 16:53

Re : Disque dur externe ne monte pas

#6 Le 12/03/2020, à 17:10

Re : Disque dur externe ne monte pas

#7 Le 12/03/2020, à 17:11

Re : Disque dur externe ne monte pas

#8 Le 12/03/2020, à 17:23

Re : Disque dur externe ne monte pas

#9 Le 12/03/2020, à 17:32

Re : Disque dur externe ne monte pas

#10 Le 12/03/2020, à 17:45

Re : Disque dur externe ne monte pas

#11 Le 13/03/2020, à 09:10

Re : Disque dur externe ne monte pas

#12 Le 13/03/2020, à 10:24

Re : Disque dur externe ne monte pas

#13 Le 13/03/2020, à 11:46

Re : Disque dur externe ne monte pas

#14 Le 13/03/2020, à 17:22

Re : Disque dur externe ne monte pas

#15 Le 13/03/2020, à 18:40

Re : Disque dur externe ne monte pas

#16 Le 13/03/2020, à 19:43

Re : Disque dur externe ne monte pas

#17 Le 14/03/2020, à 16:52

Re : Disque dur externe ne monte pas

#18 Le 14/03/2020, à 17:39

Re : Disque dur externe ne monte pas

#19 Le 03/04/2021, à 00:09

Re : Disque dur externe ne monte pas

Pied de page des forums