Pages : 1
#1 Le 07/05/2020, à 12:20
- flp
Interpréter rapport Gsmartcontrol
Bonjour,
Je souhaiterais avoir des lumières sur les résultats du short-self-test réalisé sur un disque dur externe avec Gsmartcontrol, que voici :
Complete error log:
SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
Device Error Count: 1649 (device log contains only the most recent 4 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1649 [0] occurred at disk power-on lifetime: 5125 hours (213 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 00 29 86 95 51 e9 00 Error: UNC 8 sectors at LBA = 0x29869551 = 696685905
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 29 86 95 51 e0 00 1d+01:13:01.000 READ DMA EXT
35 00 00 00 01 00 00 29 7d b3 c3 e0 00 1d+01:13:01.000 WRITE DMA EXT
ef 00 03 00 46 00 00 00 00 00 00 a0 00 1d+01:13:01.000 SET FEATURES [Set transfer mode]
25 00 00 00 08 00 00 29 86 95 51 e9 04 1d+01:13:01.000 READ DMA EXT
25 00 00 00 08 00 00 29 86 95 51 e0 00 1d+01:12:57.100 READ DMA EXT
Error 1648 [3] occurred at disk power-on lifetime: 5125 hours (213 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 00 29 86 95 51 e9 00 Error: UNC 8 sectors at LBA = 0x29869551 = 696685905
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 29 86 95 51 e0 00 1d+01:12:57.100 READ DMA EXT
25 00 00 00 08 00 00 29 86 95 49 e0 00 1d+01:12:57.100 READ DMA EXT
25 00 00 00 08 00 00 29 86 95 41 e0 00 1d+01:12:57.100 READ DMA EXT
25 00 00 00 08 00 00 29 86 95 39 e0 00 1d+01:12:57.100 READ DMA EXT
25 00 00 00 08 00 00 29 86 95 31 e0 00 1d+01:12:57.100 READ DMA EXT
Error 1647 [2] occurred at disk power-on lifetime: 5125 hours (213 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 30 00 00 29 86 95 51 e9 00 Error: UNC 48 sectors at LBA = 0x29869551 = 696685905
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 80 00 00 29 86 95 01 e0 00 1d+01:12:53.200 READ DMA EXT
25 00 00 00 80 00 00 29 86 93 81 e0 00 1d+01:12:53.200 READ DMA EXT
25 00 00 00 80 00 00 29 86 93 01 e0 00 1d+01:12:53.200 READ DMA EXT
25 00 00 00 80 00 00 29 86 91 81 e0 00 1d+01:12:53.200 READ DMA EXT
25 00 00 00 80 00 00 29 86 91 01 e0 00 1d+01:12:53.200 READ DMA EXT
Error 1646 [1] occurred at disk power-on lifetime: 5125 hours (213 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 07 00 00 29 86 8b 8a e9 00 Error: UNC 7 sectors at LBA = 0x29868b8a = 696683402
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 00 29 86 8b 89 e0 00 1d+01:12:41.200 READ DMA EXT
ef 00 03 00 46 00 00 00 00 00 00 a0 00 1d+01:12:41.200 SET FEATURES [Set transfer mode]
25 00 00 00 07 00 00 29 86 8b 8a e9 04 1d+01:12:41.100 READ DMA EXT
25 00 00 00 08 00 00 29 86 8b 89 e0 00 1d+01:12:37.300 READ DMA EXT
25 00 00 00 08 00 00 29 86 8b 81 e0 00 1d+01:12:37.300 READ DMA EXTMerci par avance !
FLP
Pc : ASUS H81M-PLUS | Linux Mint 19.3 Tricia | MATE 1.22.2 | 5.3.0-62-generic x86_64 | Dual Core Intel Pentium G3258 3.20GHz | 8Go | NVIDIA GT218 [GeForce 210]
Hors ligne
#2 Le 07/05/2020, à 13:32
- inbox
Re : Interpréter rapport Gsmartcontrol
Salut,
Donne plutôt le résultat de cette commande :
sudo smartctl -s on -a /dev/sdaA+
Un problème résolu ? Indiquez le en modifiant le titre du sujet.
Hors ligne
#3 Le 07/05/2020, à 14:03
- flp
Re : Interpréter rapport Gsmartcontrol
Le voici :
flp@flp-desktop:~$ sudo smartctl -s on -a /dev/sdg
[sudo] Mot de passe de flp :
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-5.3.0-45-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Travelstar 5K500.B
Device Model: Hitachi HTS545050B9A300
Serial Number: 101015PBN40417FAYPYE
LU WWN Device Id: 5 000cca 5f1ef41be
Firmware Version: PB4OC64G
User Capacity: 500107862016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Thu May 7 15:01:42 2020 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 117) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: ( 645) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 158) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 099 099 062 Pre-fail Always - 131072
2 Throughput_Performance 0x0005 100 100 040 Pre-fail Offline - 0
3 Spin_Up_Time 0x0007 131 131 033 Pre-fail Always - 2
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 1246
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 040 Pre-fail Offline - 0
9 Power_On_Hours 0x0012 089 089 000 Old_age Always - 5128
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 1075
191 G-Sense_Error_Rate 0x000a 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 098 098 000 Old_age Always - 543
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 1246
194 Temperature_Celsius 0x0002 130 130 000 Old_age Always - 42 (Min/Max 12/52)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 86
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 19
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
223 Load_Retry_Count 0x000a 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 1649 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1649 occurred at disk power-on lifetime: 5125 hours (213 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 51 95 86 e9 Error: UNC 8 sectors at LBA = 0x09869551 = 159814993
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 51 95 86 e0 00 1d+01:13:01.000 READ DMA EXT
35 00 01 c3 b3 7d e0 00 1d+01:13:01.000 WRITE DMA EXT
ef 03 46 00 00 00 a0 00 1d+01:13:01.000 SET FEATURES [Set transfer mode]
25 00 08 51 95 86 e9 04 1d+01:13:01.000 READ DMA EXT
25 00 08 51 95 86 e0 00 1d+01:12:57.100 READ DMA EXT
Error 1648 occurred at disk power-on lifetime: 5125 hours (213 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 51 95 86 e9 Error: UNC 8 sectors at LBA = 0x09869551 = 159814993
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 51 95 86 e0 00 1d+01:12:57.100 READ DMA EXT
25 00 08 49 95 86 e0 00 1d+01:12:57.100 READ DMA EXT
25 00 08 41 95 86 e0 00 1d+01:12:57.100 READ DMA EXT
25 00 08 39 95 86 e0 00 1d+01:12:57.100 READ DMA EXT
25 00 08 31 95 86 e0 00 1d+01:12:57.100 READ DMA EXT
Error 1647 occurred at disk power-on lifetime: 5125 hours (213 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 30 51 95 86 e9 Error: UNC 48 sectors at LBA = 0x09869551 = 159814993
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 80 01 95 86 e0 00 1d+01:12:53.200 READ DMA EXT
25 00 80 81 93 86 e0 00 1d+01:12:53.200 READ DMA EXT
25 00 80 01 93 86 e0 00 1d+01:12:53.200 READ DMA EXT
25 00 80 81 91 86 e0 00 1d+01:12:53.200 READ DMA EXT
25 00 80 01 91 86 e0 00 1d+01:12:53.200 READ DMA EXT
Error 1646 occurred at disk power-on lifetime: 5125 hours (213 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 07 8a 8b 86 e9 Error: UNC 7 sectors at LBA = 0x09868b8a = 159812490
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 89 8b 86 e0 00 1d+01:12:41.200 READ DMA EXT
ef 03 46 00 00 00 a0 00 1d+01:12:41.200 SET FEATURES [Set transfer mode]
25 00 07 8a 8b 86 e9 04 1d+01:12:41.100 READ DMA EXT
25 00 08 89 8b 86 e0 00 1d+01:12:37.300 READ DMA EXT
25 00 08 81 8b 86 e0 00 1d+01:12:37.300 READ DMA EXT
Error 1645 occurred at disk power-on lifetime: 5125 hours (213 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 07 8a 8b 86 e9 Error: UNC 7 sectors at LBA = 0x09868b8a = 159812490
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 89 8b 86 e0 00 1d+01:12:37.300 READ DMA EXT
25 00 08 81 8b 86 e0 00 1d+01:12:37.300 READ DMA EXT
35 00 01 c3 b3 7d e0 00 1d+01:12:37.300 WRITE DMA EXT
25 00 80 01 8d 86 e0 00 1d+01:12:37.300 READ DMA EXT
25 00 80 01 8c 86 e0 00 1d+01:12:37.300 READ DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed: read failure 50% 5127 695693123
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.Merci de votre attention et de vos éclairages !
Pc : ASUS H81M-PLUS | Linux Mint 19.3 Tricia | MATE 1.22.2 | 5.3.0-62-generic x86_64 | Dual Core Intel Pentium G3258 3.20GHz | 8Go | NVIDIA GT218 [GeForce 210]
Hors ligne
#4 Le 07/05/2020, à 14:18
- inbox
Re : Interpréter rapport Gsmartcontrol
Les deux lignes importantes sont celles ci :
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 86
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 1986 secteurs on été réalloués sur des secteurs de rechange
19 secteurs sont en attente de réallocation
==> Une partie du disque dur est inutilisable.
Le plus sûr est de changer ce disque dur avant qu'il ne se dégrade encore plus. Le minimum à faire est d'en sauvegarder le contenu sur un autre disque dur.
Un problème résolu ? Indiquez le en modifiant le titre du sujet.
Hors ligne
#5 Le 07/05/2020, à 18:44
- flp
Re : Interpréter rapport Gsmartcontrol
Merci pour ta réponse.
La partie inutilisable est-elle importante en proportion ?
Ai-je une chance d'améliorer la situation en le formatant ?
Pc : ASUS H81M-PLUS | Linux Mint 19.3 Tricia | MATE 1.22.2 | 5.3.0-62-generic x86_64 | Dual Core Intel Pentium G3258 3.20GHz | 8Go | NVIDIA GT218 [GeForce 210]
Hors ligne
#6 Le 07/05/2020, à 18:56
- inbox
Re : Interpréter rapport Gsmartcontrol
Formater un disque défectueux ne répare rien. Les secteurs défectueux le resteront. Je ne sais pas quelle partie du disque est HS.
Je répète que la meilleure idée est de changer de disque.
Un problème résolu ? Indiquez le en modifiant le titre du sujet.
Hors ligne
Pages : 1