#1 Le 15/02/2024, à 14:06
- RIMBAUT
pilote rtl8xxxu a remplacé le rtl8198eu RÉSOLU
Bonjour,
j'ai installer Xubuntu Jammy Jellyfish 22.04.3 sur Dell Latitude E5420 . Quand le Bluetooth est activé pour une enceinte à distance, le wifi se déconnecte. Dois-je installer une autre version de linux ?
Sur un Dell E4200 avec la version Xubuntu 22.04 je n'ai pas ce problème, mais cette version n'est plus proposée à télécharger sur le site Ubuntu.
Merci de votre aide.
Dernière modification par RIMBAUT (Le 17/02/2024, à 11:35)
Hors ligne
#2 Le 15/02/2024, à 14:15
- xubu1957
Re : pilote rtl8xxxu a remplacé le rtl8198eu RÉSOLU
Bonjour,
Avec la carte Wi-Fi BCM4322 ?
Montre :
iwconfignmcli dev wifi | catsudo lshw -class networkPour le pilote RTL 8192EU de la clé wifi > [RÉSOLU] Problème installation pilote RTL8192EU sur Xubuntu 22.04
Dernière modification par xubu1957 (Le 15/02/2024, à 19:59)
Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Réso|u] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci. Membre de Linux-Azur
Hors ligne
#3 Le 15/02/2024, à 14:23
- RIMBAUT
Re : pilote rtl8xxxu a remplacé le rtl8198eu RÉSOLU
Je suis en pause travail, je te donnerai les infos ce soir. Je suis sur clé wifi et sur pilote RTL8192EU, ce pilote que tu m'as aidé à installer.
A ce soir.
Hors ligne
#4 Le 15/02/2024, à 19:58
- RIMBAUT
Re : pilote rtl8xxxu a remplacé le rtl8198eu RÉSOLU
symeon@symeon-Latitude-E5420:~$ iwconfig
lo no wireless extensions.
enp10s0 no wireless extensions.
wwx028037ec0200 no wireless extensions.
wlx00e04c16cfec IEEE 802.11 ESSID:"Livebox-2EBC"
Mode:Managed Frequency:2.462 GHz Access Point: AC:B6:87:74:2E:BC
Bit Rate=78 Mb/s Tx-Power=20 dBm
Retry short limit:7 RTS thr=2347 B Fragment thr:off
Power Management:off
Link Quality=38/70 Signal level=-72 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:22 Missed beacon:0
wlp2s0b1 IEEE 802.11 ESSID:"Livebox-2EBC"
Mode:Managed Frequency:2.462 GHz Access Point: AC:B6:87:74:2E:BC
Bit Rate=7.2 Mb/s Tx-Power=19 dBm
Retry short limit:7 RTS thr:off Fragment thr:off
Power Management:off
Link Quality=26/70 Signal level=-84 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:181 Invalid misc:22 Missed beacon:0
symeon@symeon-Latitude-E5420:~$ nmcli dev wifi | cat
sudo lshw -class network
IN-USE BSSID SSID MODE CHAN RATE SIGNAL BARS SECURITY
* AC:B6:87:74:2E:BC Livebox-2EBC Infra 11 130 Mbit/s 48 ▂▄__ WPA2
30:7C:B2:3C:D7:BF Livebox-D7BF Infra 6 130 Mbit/s 7 ▂___ WPA1 WPA2
16:CA:2F:04:67:0F Maxime's Galaxy A14 Infra 6 117 Mbit/s 7 ▂___ WPA2
44:D4:53:95:5C:F8 Livebox-7C40 Infra 11 405 Mbit/s 7 ▂___ WPA2
70:FC:8F:B8:CB:94 Freebox-A344B1 Infra 11 195 Mbit/s 7 ▂___ WPA2
EC:6C:9A:B4:10:8A Livebox-108A Infra 11 130 Mbit/s 7 ▂___ WPA2
IN-USE BSSID SSID MODE CHAN RATE SIGNAL BARS SECURITY
* AC:B6:87:74:2E:BC Livebox-2EBC Infra 11 130 Mbit/s 33 ▂▄__ WPA2
16:CA:2F:04:67:0F Maxime's Galaxy A14 Infra 6 117 Mbit/s 19 ▂___ WPA2
[sudo] Mot de passe de symeon :
Désolé, essayez de nouveau.
[sudo] Mot de passe de symeon :
*-network
description: Interface réseau sans fil
produit: BCM4313 802.11bgn Wireless Network Adapter
fabricant: Broadcom Inc. and subsidiaries
identifiant matériel: 0
information bus: pci@0000:02:00.0
nom logique: wlp2s0b1
version: 01
numéro de série: 38:59:f9:8d:8a:86
bits: 64 bits
horloge: 33MHz
fonctionnalités: pm msi pciexpress bus_master cap_list ethernet physical wireless
configuration : broadcast=yes driver=brcmsmac driverversion=6.5.0-17-generic firmware=610.812 latency=0 link=no multicast=yes wireless=IEEE 802.11
ressources : irq:17 mémoire:93c00000-93c03fff
*-network
description: Ethernet interface
produit: NetXtreme BCM5761 Gigabit Ethernet PCIe
fabricant: Broadcom Inc. and subsidiaries
identifiant matériel: 0
information bus: pci@0000:0a:00.0
nom logique: enp10s0
version: 10
numéro de série: d0:67:e5:33:ce:ff
capacité: 1Gbit/s
bits: 64 bits
horloge: 33MHz
fonctionnalités: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
configuration : autonegotiation=on broadcast=yes driver=tg3 driverversion=6.5.0-17-generic firmware=5761-v3.78 latency=0 link=no multicast=yes port=twisted pair
ressources : irq:27 mémoire:92010000-9201ffff mémoire:92000000-9200ffff
*-network:0 DÉSACTIVÉ
description: Ethernet interface
identifiant matériel: a
information bus: usb@2:1.6
nom logique: wwx028037ec0200
numéro de série: 02:80:37:ec:02:00
fonctionnalités: ethernet physical
configuration : autonegotiation=off broadcast=yes driver=cdc_ncm driverversion=6.5.0-17-generic duplex=half firmware=Mobile Broadband Network Device link=no multicast=yes port=twisted pair
*-network:1
description: Interface réseau sans fil
identifiant matériel: b
information bus: usb@1:1.3
nom logique: wlx00e04c16cfec
numéro de série: 00:e0:4c:16:cf:ec
fonctionnalités: ethernet physical wireless
configuration : broadcast=yes driver=rtl8xxxu driverversion=6.5.0-17-generic firmware=N/A ip=192.168.1.12 link=yes multicast=yes wireless=IEEE 802.11
symeon@symeon-Latitude-E5420:~$ Hors ligne
#5 Le 15/02/2024, à 20:00
- xubu1957
Re : pilote rtl8xxxu a remplacé le rtl8198eu RÉSOLU
Montre :
lsusbConseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Réso|u] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci. Membre de Linux-Azur
Hors ligne
#6 Le 15/02/2024, à 20:06
- RIMBAUT
Re : pilote rtl8xxxu a remplacé le rtl8198eu RÉSOLU
symeon@symeon-Latitude-E5420:~$ lsusb
Bus 001 Device 011: ID 413c:8187 Dell Computer Corp. DW375 Bluetooth Module
Bus 001 Device 010: ID 248a:00da Maxxter Wireless Receiver
Bus 001 Device 009: ID 1ea7:0066 SHARKOON Technologies GmbH [Mediatrack Edge Mini Keyboard]
Bus 001 Device 004: ID 05e3:0608 Genesys Logic, Inc. Hub
Bus 001 Device 003: ID 0bda:818b Realtek Semiconductor Corp. RTL8192EU 802.11b/g/n WLAN Adapter
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 003: ID 413c:818d Dell Computer Corp. DW5550
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
symeon@symeon-Latitude-E5420:~$ Hors ligne
#7 Le 15/02/2024, à 20:11
- xubu1957
Re : pilote rtl8xxxu a remplacé le rtl8198eu RÉSOLU
C'est nouveau cette carte ?
BCM4313 802.11bgn Wireless Network AdapterConseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Réso|u] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci. Membre de Linux-Azur
Hors ligne
#8 Le 15/02/2024, à 20:14
- RIMBAUT
Re : pilote rtl8xxxu a remplacé le rtl8198eu RÉSOLU
Je viens de connecter l'enceinte sur le bluetooth. La deconnexion se produit qsuand je regarde un film en streaming, alors qs'avec le dell 4200 et xubbuntu 22.04 tout va bien.
Hors ligne
#9 Le 15/02/2024, à 20:15
- RIMBAUT
Re : pilote rtl8xxxu a remplacé le rtl8198eu RÉSOLU
Non la carte est d'origine. Je suis sur clé wifi et sur pilote RTL8192EU, ce pilote que tu m'as aidé à installer.
Dernière modification par RIMBAUT (Le 15/02/2024, à 20:16)
Hors ligne
#10 Le 15/02/2024, à 20:23
- RIMBAUT
Re : pilote rtl8xxxu a remplacé le rtl8198eu RÉSOLU
Je refais un essai avec le streaming
Hors ligne
#11 Le 15/02/2024, à 20:39
- xubu1957
Re : pilote rtl8xxxu a remplacé le rtl8198eu RÉSOLU
Pour cet ordi Latitude-E5420, fournis pour le Bluetooth :
uname -a; lspci -nnk | grep -iA3 net; lsusb; sudo dmesg | grep -i bluetooth; sudo dmesg | grep -i firmware; lsmod | grep bluetoothdpkg -l | grep bluerfkill list allsudo service bluetooth status | catDernière modification par xubu1957 (Le 15/02/2024, à 20:51)
Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Réso|u] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci. Membre de Linux-Azur
Hors ligne
#12 Le 15/02/2024, à 20:50
- Astrolivier
Re : pilote rtl8xxxu a remplacé le rtl8198eu RÉSOLU
salut,
si tu veux tu peux tester mon script en version très longue qui donnera la liste des paramètres pour les modules et pour ta carte wifi (enfin les deux d'ailleurs... normalement)
https://github.com/olivierPrigent/wifiCheck/tree/main
pour installer les paquets nécessaires (normalement ils seront tous déjà là)
sudo apt install dkms rfkill iw network-manager lshw mokutilpour télécharger le script, mettre les droits et le lancer. attention ça va être long (le texte)
wget -N -t 5 -T 10 https://raw.githubusercontent.com/olivierPrigent/wifiCheck/main/wificheck.sh && chmod 755 wificheck.sh && ./wificheck.sh -vc'est encore un peu en beta test, j'ai une version améliorée que je dois remonter, mais ça ne risque rien. il y aura juste à copier coller, les balises codes sont déjà incluses.
c'est si tu veux bien être un beta testeur 
autrement donne
iw list
modinfo rtl8xxxu |grep parmS'il faut absolument faire des sacrifices pour assurer le progrès de l'humanité, ne serait-il pas indispensable de s'en tenir au principe selon lequel c'est à ceux dont on exige le sacrifice que la décision doit revenir en dernier ressort ? (howard zinn)
Hors ligne
#13 Le 15/02/2024, à 20:51
- RIMBAUT
Re : pilote rtl8xxxu a remplacé le rtl8198eu RÉSOLU
Pour être plus précis, le pc se met en gel lorsque le streaming est activé. Je suis obligé de l'ételndre forcé sur le on/off de l'ordi et de le rallumer.
Je te donne les info
Hors ligne
#14 Le 15/02/2024, à 20:54
- RIMBAUT
Re : pilote rtl8xxxu a remplacé le rtl8198eu RÉSOLU
Pour Xubu
symeon@symeon-Latitude-E5420:~$ uname -a; lspci -nnk | grep -iA3 net; lsusb; sudo dmesg | grep -i bluetooth; sudo dmesg | grep -i firmware; lsmod | grep bluetooth
Linux symeon-Latitude-E5420 6.5.0-17-generic #17~22.04.1-Ubuntu SMP PREEMPT_DYNAMIC Tue Jan 16 14:32:32 UTC 2 x86_64 x86_64 x86_64 GNU/Linux
02:00.0 Network controller [0280]: Broadcom Inc. and subsidiaries BCM4313 802.11bgn Wireless Network Adapter [14e4:4727] (rev 01)
Subsystem: Dell Inspiron M5010 / XPS 8300 [1028:0010]
Kernel driver in use: bcma-pci-bridge
Kernel modules: bcma
--
0a:00.0 Ethernet controller [0200]: Broadcom Inc. and subsidiaries NetXtreme BCM5761 Gigabit Ethernet PCIe [14e4:1681] (rev 10)
Subsystem: Dell NetXtreme BCM5761 Gigabit Ethernet PCIe [1028:049b]
Kernel driver in use: tg3
Kernel modules: tg3
Bus 002 Device 005: ID 413c:8187 Dell Computer Corp. DW375 Bluetooth Module
Bus 002 Device 007: ID 248a:00da Maxxter Wireless Receiver
Bus 002 Device 006: ID 1ea7:0066 SHARKOON Technologies GmbH [Mediatrack Edge Mini Keyboard]
Bus 002 Device 004: ID 05e3:0608 Genesys Logic, Inc. Hub
Bus 002 Device 003: ID 0bda:818b Realtek Semiconductor Corp. RTL8192EU 802.11b/g/n WLAN Adapter
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 413c:818d Dell Computer Corp. DW5550
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
[sudo] Mot de passe de symeon :
[ 1.898422] usb 2-1.6: Product: DW375 Bluetooth Module
[ 27.893876] Bluetooth: Core ver 2.22
[ 27.893913] NET: Registered PF_BLUETOOTH protocol family
[ 27.893917] Bluetooth: HCI device and connection manager initialized
[ 27.893924] Bluetooth: HCI socket layer initialized
[ 27.893928] Bluetooth: L2CAP socket layer initialized
[ 27.893936] Bluetooth: SCO socket layer initialized
[ 48.558382] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 48.558389] Bluetooth: BNEP filters: protocol multicast
[ 48.558396] Bluetooth: BNEP socket layer initialized
[ 48.613144] Bluetooth: MGMT ver 1.22
[ 74.530378] Bluetooth: RFCOMM TTY layer initialized
[ 74.530398] Bluetooth: RFCOMM socket layer initialized
[ 74.530411] Bluetooth: RFCOMM ver 1.11
[ 0.116639] Spectre V2 : Enabling Restricted Speculation for firmware calls
[ 0.186955] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
[ 29.024519] usb 2-1.3: rtl8xxxu: Loading firmware rtlwifi/rtl8192eu_nic.bin
[ 29.422753] usb 2-1.3: Firmware revision 19.0 (signature 0x92e1)
bluetooth 1073152 38 btrtl,btmtk,btintel,btbcm,bnep,btusb,rfcomm
ecdh_generic 16384 1 bluetooth
symeon@symeon-Latitude-E5420:~$ dpkg -l | grep blue
ii blueman 2.2.4-1 amd64 Graphical bluetooth manager
ii bluez 5.64-0ubuntu1.1 amd64 Bluetooth tools and daemons
ii bluez-cups 5.64-0ubuntu1.1 amd64 Bluetooth printer driver for CUPS
ii bluez-obexd 5.64-0ubuntu1.1 amd64 bluez obex daemon
ii libbluetooth3:amd64 5.64-0ubuntu1.1 amd64 Library to use the BlueZ Linux Bluetooth stack
ii pulseaudio-module-bluetooth 1:15.99.1+dfsg1-1ubuntu2.1 amd64 Bluetooth module for PulseAudio sound server
symeon@symeon-Latitude-E5420:~$ rfkill list all
0: hci0: Bluetooth
Soft blocked: no
Hard blocked: no
1: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no
2: dell-wifi: Wireless LAN
Soft blocked: no
Hard blocked: no
3: dell-bluetooth: Bluetooth
Soft blocked: no
Hard blocked: no
4: dell-wwan: Wireless WAN
Soft blocked: no
Hard blocked: no
5: phy1: Wireless LAN
Soft blocked: no
Hard blocked: no
symeon@symeon-Latitude-E5420:~$ sudo service bluetooth status | cat
● bluetooth.service - Bluetooth service
Loaded: loaded (/lib/systemd/system/bluetooth.service; enabled; vendor preset: enabled)
Active: active (running) since Thu 2024-02-15 20:45:35 CET; 8min ago
Docs: man:bluetoothd(8)
Main PID: 546 (bluetoothd)
Status: "Running"
Tasks: 1 (limit: 2070)
Memory: 260.0K
CPU: 151ms
CGroup: /system.slice/bluetooth.service
└─546 /usr/lib/bluetooth/bluetoothd
févr. 15 20:46:14 symeon-Latitude-E5420 bluetoothd[546]: Endpoint unregistered: sender=:1.38 path=/MediaEndpoint/A2DPSink/sbc_xq_552
févr. 15 20:46:14 symeon-Latitude-E5420 bluetoothd[546]: Endpoint unregistered: sender=:1.38 path=/MediaEndpoint/A2DPSource/sbc_xq_552
févr. 15 20:46:15 symeon-Latitude-E5420 bluetoothd[546]: Endpoint registered: sender=:1.50 path=/MediaEndpoint/A2DPSink/sbc
févr. 15 20:46:15 symeon-Latitude-E5420 bluetoothd[546]: Endpoint registered: sender=:1.50 path=/MediaEndpoint/A2DPSource/sbc
févr. 15 20:46:15 symeon-Latitude-E5420 bluetoothd[546]: Endpoint registered: sender=:1.50 path=/MediaEndpoint/A2DPSink/sbc_xq_453
févr. 15 20:46:15 symeon-Latitude-E5420 bluetoothd[546]: Endpoint registered: sender=:1.50 path=/MediaEndpoint/A2DPSource/sbc_xq_453
févr. 15 20:46:15 symeon-Latitude-E5420 bluetoothd[546]: Endpoint registered: sender=:1.50 path=/MediaEndpoint/A2DPSink/sbc_xq_512
févr. 15 20:46:15 symeon-Latitude-E5420 bluetoothd[546]: Endpoint registered: sender=:1.50 path=/MediaEndpoint/A2DPSource/sbc_xq_512
févr. 15 20:46:15 symeon-Latitude-E5420 bluetoothd[546]: Endpoint registered: sender=:1.50 path=/MediaEndpoint/A2DPSink/sbc_xq_552
févr. 15 20:46:15 symeon-Latitude-E5420 bluetoothd[546]: Endpoint registered: sender=:1.50 path=/MediaEndpoint/A2DPSource/sbc_xq_552
symeon@symeon-Latitude-E5420:~$ Hors ligne
#15 Le 15/02/2024, à 21:02
- RIMBAUT
Re : pilote rtl8xxxu a remplacé le rtl8198eu RÉSOLU
Bonsoir Olivier,
je ptèsfère suivre d'abord le protocole de xubu1957, sinon je risque de tout mélanger. Merci de ton aide.
Hors ligne
#16 Le 15/02/2024, à 21:08
- RIMBAUT
Re : pilote rtl8xxxu a remplacé le rtl8198eu RÉSOLU
Je fais un essai avec yputube pour voir si l'ordi se met en gel. Peut-être que c'est le site streaming qui perturbe le pc ?
Hors ligne
#17 Le 15/02/2024, à 21:32
- RIMBAUT
Re : pilote rtl8xxxu a remplacé le rtl8198eu RÉSOLU
Bon sur youtube, le pc ne se met pas en gel. Ça vient certainement du site streaming.
Hors ligne
#18 Le 15/02/2024, à 21:36
- xubu1957
Re : pilote rtl8xxxu a remplacé le rtl8198eu RÉSOLU
Fournis le wificheck, il va aussi donner d'autres renseignements.
Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Réso|u] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci. Membre de Linux-Azur
Hors ligne
#19 Le 15/02/2024, à 21:47
- RIMBAUT
Re : pilote rtl8xxxu a remplacé le rtl8198eu RÉSOLU
Bon j'ai paelé trop vite, le pc s'est mis en gel en regardant youtube. Je fournis le wificheck
Hors ligne
#20 Le 15/02/2024, à 21:51
- RIMBAUT
Re : pilote rtl8xxxu a remplacé le rtl8198eu RÉSOLU
symeon@symeon-Latitude-E5420:~$ sudo apt install dkms rfkill iw network-manager lshw mokutil
[sudo] Mot de passe de symeon :
Lecture des listes de paquets... Fait
Construction de l'arbre des dépendances... Fait
Lecture des informations d'état... Fait
lshw est déjà la version la plus récente (02.19.git.2021.06.19.996aaad9c7-2build1).
lshw passé en « installé manuellement ».
rfkill est déjà la version la plus récente (2.37.2-4ubuntu3).
rfkill passé en « installé manuellement ».
mokutil est déjà la version la plus récente (0.6.0-2~22.04.2).
network-manager est déjà la version la plus récente (1.36.6-0ubuntu2).
network-manager passé en « installé manuellement ».
Les paquets suivants ont été installés automatiquement et ne sont plus nécessaires :
kdegames-mahjongg-data-kf5 libqt5designer5 libqt5help5 libqt5sql5
libqt5sql5-sqlite libqt5test5 python3-attr python3-automat python3-bcrypt
python3-constantly python3-hamcrest python3-hyperlink python3-incremental
python3-pyasn1 python3-pyasn1-modules python3-pyqt5 python3-pyqt5.qtsvg
python3-pyqt5.sip python3-service-identity python3-twisted
python3-zope.interface
Veuillez utiliser « sudo apt autoremove » pour les supprimer.
Les paquets supplémentaires suivants seront installés :
binutils binutils-common binutils-x86-64-linux-gnu build-essential cpp-12
dctrl-tools dpkg-dev fakeroot g++ g++-11 gcc gcc-11 gcc-12
libalgorithm-diff-perl libalgorithm-diff-xs-perl libalgorithm-merge-perl
libasan6 libasan8 libbinutils libc-dev-bin libc-devtools libc6-dev libcc1-0
libcrypt-dev libctf-nobfd0 libctf0 libdpkg-perl libfakeroot
libfile-fcntllock-perl libgcc-11-dev libgcc-12-dev libitm1 liblsan0
libnsl-dev libstdc++-11-dev libtirpc-dev libtsan0 libtsan2 libubsan1
linux-libc-dev lto-disabled-list manpages-dev rpcsvc-proto
Paquets suggérés :
binutils-doc gcc-12-locales cpp-12-doc debtags menu debian-keyring
g++-multilib g++-11-multilib gcc-11-doc gcc-multilib autoconf automake
libtool flex bison gcc-doc gcc-11-multilib gcc-11-locales gcc-12-multilib
gcc-12-doc glibc-doc bzr libstdc++-11-doc
Les NOUVEAUX paquets suivants seront installés :
binutils binutils-common binutils-x86-64-linux-gnu build-essential cpp-12
dctrl-tools dkms dpkg-dev fakeroot g++ g++-11 gcc gcc-11 gcc-12 iw
libalgorithm-diff-perl libalgorithm-diff-xs-perl libalgorithm-merge-perl
libasan6 libasan8 libbinutils libc-dev-bin libc-devtools libc6-dev libcc1-0
libcrypt-dev libctf-nobfd0 libctf0 libdpkg-perl libfakeroot
libfile-fcntllock-perl libgcc-11-dev libgcc-12-dev libitm1 liblsan0
libnsl-dev libstdc++-11-dev libtirpc-dev libtsan0 libtsan2 libubsan1
linux-libc-dev lto-disabled-list manpages-dev rpcsvc-proto
0 mis à jour, 45 nouvellement installés, 0 à enlever et 3 non mis à jour.
Il est nécessaire de prendre 94,3 Mo dans les archives.
Après cette opération, 325 Mo d'espace disque supplémentaires seront utilisés.
Souhaitez-vous continuer ? [O/n]
Réception de :1 http://fr.archive.ubuntu.com/ubuntu jammy-updates/main amd64 libcc1-0 amd64 12.3.0-1ubuntu1~22.04 [48,3 kB]
Réception de :2 http://fr.archive.ubuntu.com/ubuntu jammy-updates/main amd64 binutils-common amd64 2.38-4ubuntu2.5 [222 kB]
Réception de :3 http://fr.archive.ubuntu.com/ubuntu jammy-updates/main amd64 libbinutils amd64 2.38-4ubuntu2.5 [662 kB]
Réception de :4 http://fr.archive.ubuntu.com/ubuntu jammy-updates/main amd64 libctf-nobfd0 amd64 2.38-4ubuntu2.5 [108 kB]
Réception de :5 http://fr.archive.ubuntu.com/ubuntu jammy-updates/main amd64 libctf0 amd64 2.38-4ubuntu2.5 [103 kB]
Réception de :6 http://fr.archive.ubuntu.com/ubuntu jammy-updates/main amd64 binutils-x86-64-linux-gnu amd64 2.38-4ubuntu2.5 [2326 kB]
Réception de :7 http://fr.archive.ubuntu.com/ubuntu jammy-updates/main amd64 binutils amd64 2.38-4ubuntu2.5 [3202 B]
Réception de :8 http://fr.archive.ubuntu.com/ubuntu jammy-updates/main amd64 libitm1 amd64 12.3.0-1ubuntu1~22.04 [30,2 kB]
Réception de :9 http://fr.archive.ubuntu.com/ubuntu jammy-updates/main amd64 libasan6 amd64 11.4.0-1ubuntu1~22.04 [2282 kB]
Réception de :10 http://fr.archive.ubuntu.com/ubuntu jammy-updates/main amd64 liblsan0 amd64 12.3.0-1ubuntu1~22.04 [1069 kB]
Réception de :11 http://fr.archive.ubuntu.com/ubuntu jammy-updates/main amd64 libtsan0 amd64 11.4.0-1ubuntu1~22.04 [2260 kB]
Réception de :12 http://fr.archive.ubuntu.com/ubuntu jammy-updates/main amd64 libubsan1 amd64 12.3.0-1ubuntu1~22.04 [976 kB]
Réception de :13 http://fr.archive.ubuntu.com/ubuntu jammy-updates/main amd64 libgcc-11-dev amd64 11.4.0-1ubuntu1~22.04 [2517 kB]
Réception de :14 http://fr.archive.ubuntu.com/ubuntu jammy-updates/main amd64 gcc-11 amd64 11.4.0-1ubuntu1~22.04 [20,1 MB]
Réception de :15 http://fr.archive.ubuntu.com/ubuntu jammy/main amd64 gcc amd64 4:11.2.0-1ubuntu1 [5112 B]
Réception de :16 http://fr.archive.ubuntu.com/ubuntu jammy-updates/main amd64 cpp-12 amd64 12.3.0-1ubuntu1~22.04 [10,8 MB]
Réception de :17 http://fr.archive.ubuntu.com/ubuntu jammy-updates/main amd64 libasan8 amd64 12.3.0-1ubuntu1~22.04 [2442 kB]
Réception de :18 http://fr.archive.ubuntu.com/ubuntu jammy-updates/main amd64 libtsan2 amd64 12.3.0-1ubuntu1~22.04 [2477 kB]
Réception de :19 http://fr.archive.ubuntu.com/ubuntu jammy-updates/main amd64 libgcc-12-dev amd64 12.3.0-1ubuntu1~22.04 [2618 kB]
Réception de :20 http://fr.archive.ubuntu.com/ubuntu jammy-updates/main amd64 gcc-12 amd64 12.3.0-1ubuntu1~22.04 [21,7 MB]
Réception de :21 http://fr.archive.ubuntu.com/ubuntu jammy-updates/main amd64 libdpkg-perl all 1.21.1ubuntu2.2 [237 kB]
Réception de :22 http://fr.archive.ubuntu.com/ubuntu jammy/main amd64 lto-disabled-list all 24 [12,5 kB]
Réception de :23 http://fr.archive.ubuntu.com/ubuntu jammy-updates/main amd64 dpkg-dev all 1.21.1ubuntu2.2 [922 kB]
Réception de :24 http://fr.archive.ubuntu.com/ubuntu jammy-updates/main amd64 libc-dev-bin amd64 2.35-0ubuntu3.6 [20,3 kB]
Réception de :25 http://fr.archive.ubuntu.com/ubuntu jammy-updates/main amd64 linux-libc-dev amd64 5.15.0-94.104 [1355 kB]
Réception de :26 http://fr.archive.ubuntu.com/ubuntu jammy/main amd64 libcrypt-dev amd64 1:4.4.27-1 [112 kB]
Réception de :27 http://fr.archive.ubuntu.com/ubuntu jammy/main amd64 rpcsvc-proto amd64 1.4.2-0ubuntu6 [68,5 kB]
Réception de :28 http://fr.archive.ubuntu.com/ubuntu jammy-updates/main amd64 libtirpc-dev amd64 1.3.2-2ubuntu0.1 [192 kB]
Réception de :29 http://fr.archive.ubuntu.com/ubuntu jammy/main amd64 libnsl-dev amd64 1.3.0-2build2 [71,3 kB]
Réception de :30 http://fr.archive.ubuntu.com/ubuntu jammy-updates/main amd64 libc6-dev amd64 2.35-0ubuntu3.6 [2100 kB]
Réception de :31 http://fr.archive.ubuntu.com/ubuntu jammy-updates/main amd64 libstdc++-11-dev amd64 11.4.0-1ubuntu1~22.04 [2101 kB]
Réception de :32 http://fr.archive.ubuntu.com/ubuntu jammy-updates/main amd64 g++-11 amd64 11.4.0-1ubuntu1~22.04 [11,4 MB]
Réception de :33 http://fr.archive.ubuntu.com/ubuntu jammy/main amd64 g++ amd64 4:11.2.0-1ubuntu1 [1412 B]
Réception de :34 http://fr.archive.ubuntu.com/ubuntu jammy/main amd64 build-essential amd64 12.9ubuntu3 [4744 B]
Réception de :35 http://fr.archive.ubuntu.com/ubuntu jammy/main amd64 dctrl-tools amd64 2.24-3build2 [66,9 kB]
Réception de :36 http://fr.archive.ubuntu.com/ubuntu jammy-updates/main amd64 dkms all 2.8.7-2ubuntu2.2 [70,1 kB]
Réception de :37 http://fr.archive.ubuntu.com/ubuntu jammy/main amd64 libfakeroot amd64 1.28-1ubuntu1 [31,5 kB]
Réception de :38 http://fr.archive.ubuntu.com/ubuntu jammy/main amd64 fakeroot amd64 1.28-1ubuntu1 [60,4 kB]
Réception de :39 http://fr.archive.ubuntu.com/ubuntu jammy/main amd64 iw amd64 5.16-1build1 [108 kB]
Réception de :40 http://fr.archive.ubuntu.com/ubuntu jammy/main amd64 libalgorithm-diff-perl all 1.201-1 [41,8 kB]
Réception de :41 http://fr.archive.ubuntu.com/ubuntu jammy/main amd64 libalgorithm-diff-xs-perl amd64 0.04-6build3 [11,9 kB]
Réception de :42 http://fr.archive.ubuntu.com/ubuntu jammy/main amd64 libalgorithm-merge-perl all 0.08-3 [12,0 kB]
Réception de :43 http://fr.archive.ubuntu.com/ubuntu jammy-updates/main amd64 libc-devtools amd64 2.35-0ubuntu3.6 [29,0 kB]
Réception de :44 http://fr.archive.ubuntu.com/ubuntu jammy/main amd64 libfile-fcntllock-perl amd64 0.22-3build7 [33,9 kB]
Réception de :45 http://fr.archive.ubuntu.com/ubuntu jammy/main amd64 manpages-dev all 5.10-1ubuntu1 [2309 kB]
94,3 Mo réceptionnés en 31s (3041 ko/s)
Extraction des modèles depuis les paquets : 100%
Sélection du paquet libcc1-0:amd64 précédemment désélectionné.
(Lecture de la base de données... 212986 fichiers et répertoires déjà installés.
)
Préparation du dépaquetage de .../00-libcc1-0_12.3.0-1ubuntu1~22.04_amd64.deb ..
.
Dépaquetage de libcc1-0:amd64 (12.3.0-1ubuntu1~22.04) ...
Sélection du paquet binutils-common:amd64 précédemment désélectionné.
Préparation du dépaquetage de .../01-binutils-common_2.38-4ubuntu2.5_amd64.deb .
..
Dépaquetage de binutils-common:amd64 (2.38-4ubuntu2.5) ...
Sélection du paquet libbinutils:amd64 précédemment désélectionné.
Préparation du dépaquetage de .../02-libbinutils_2.38-4ubuntu2.5_amd64.deb ...
Dépaquetage de libbinutils:amd64 (2.38-4ubuntu2.5) ...
Sélection du paquet libctf-nobfd0:amd64 précédemment désélectionné.
Préparation du dépaquetage de .../03-libctf-nobfd0_2.38-4ubuntu2.5_amd64.deb ...
Dépaquetage de libctf-nobfd0:amd64 (2.38-4ubuntu2.5) ...
Sélection du paquet libctf0:amd64 précédemment désélectionné.
Préparation du dépaquetage de .../04-libctf0_2.38-4ubuntu2.5_amd64.deb ...
Dépaquetage de libctf0:amd64 (2.38-4ubuntu2.5) ...
Sélection du paquet binutils-x86-64-linux-gnu précédemment désélectionné.
Préparation du dépaquetage de .../05-binutils-x86-64-linux-gnu_2.38-4ubuntu2.5_a
md64.deb ...
Dépaquetage de binutils-x86-64-linux-gnu (2.38-4ubuntu2.5) ...
Sélection du paquet binutils précédemment désélectionné.
Préparation du dépaquetage de .../06-binutils_2.38-4ubuntu2.5_amd64.deb ...
Dépaquetage de binutils (2.38-4ubuntu2.5) ...
Sélection du paquet libitm1:amd64 précédemment désélectionné.
Préparation du dépaquetage de .../07-libitm1_12.3.0-1ubuntu1~22.04_amd64.deb ...
Dépaquetage de libitm1:amd64 (12.3.0-1ubuntu1~22.04) ...
Sélection du paquet libasan6:amd64 précédemment désélectionné.
Préparation du dépaquetage de .../08-libasan6_11.4.0-1ubuntu1~22.04_amd64.deb ..
.
Dépaquetage de libasan6:amd64 (11.4.0-1ubuntu1~22.04) ...
Sélection du paquet liblsan0:amd64 précédemment désélectionné.
Préparation du dépaquetage de .../09-liblsan0_12.3.0-1ubuntu1~22.04_amd64.deb ..
.
Dépaquetage de liblsan0:amd64 (12.3.0-1ubuntu1~22.04) ...
Sélection du paquet libtsan0:amd64 précédemment désélectionné.
Préparation du dépaquetage de .../10-libtsan0_11.4.0-1ubuntu1~22.04_amd64.deb ..
.
Dépaquetage de libtsan0:amd64 (11.4.0-1ubuntu1~22.04) ...
Sélection du paquet libubsan1:amd64 précédemment désélectionné.
Préparation du dépaquetage de .../11-libubsan1_12.3.0-1ubuntu1~22.04_amd64.deb .
..
Dépaquetage de libubsan1:amd64 (12.3.0-1ubuntu1~22.04) ...
Sélection du paquet libgcc-11-dev:amd64 précédemment désélectionné.
Préparation du dépaquetage de .../12-libgcc-11-dev_11.4.0-1ubuntu1~22.04_amd64.d
eb ...
Dépaquetage de libgcc-11-dev:amd64 (11.4.0-1ubuntu1~22.04) ...
Sélection du paquet gcc-11 précédemment désélectionné.
Préparation du dépaquetage de .../13-gcc-11_11.4.0-1ubuntu1~22.04_amd64.deb ...
Dépaquetage de gcc-11 (11.4.0-1ubuntu1~22.04) ...
Sélection du paquet gcc précédemment désélectionné.
Préparation du dépaquetage de .../14-gcc_4%3a11.2.0-1ubuntu1_amd64.deb ...
Dépaquetage de gcc (4:11.2.0-1ubuntu1) ...
Sélection du paquet cpp-12 précédemment désélectionné.
Préparation du dépaquetage de .../15-cpp-12_12.3.0-1ubuntu1~22.04_amd64.deb ...
Dépaquetage de cpp-12 (12.3.0-1ubuntu1~22.04) ...
Sélection du paquet libasan8:amd64 précédemment désélectionné.
Préparation du dépaquetage de .../16-libasan8_12.3.0-1ubuntu1~22.04_amd64.deb ..
.
Dépaquetage de libasan8:amd64 (12.3.0-1ubuntu1~22.04) ...
Sélection du paquet libtsan2:amd64 précédemment désélectionné.
Préparation du dépaquetage de .../17-libtsan2_12.3.0-1ubuntu1~22.04_amd64.deb ..
.
Dépaquetage de libtsan2:amd64 (12.3.0-1ubuntu1~22.04) ...
Sélection du paquet libgcc-12-dev:amd64 précédemment désélectionné.
Préparation du dépaquetage de .../18-libgcc-12-dev_12.3.0-1ubuntu1~22.04_amd64.d
eb ...
Dépaquetage de libgcc-12-dev:amd64 (12.3.0-1ubuntu1~22.04) ...
Sélection du paquet gcc-12 précédemment désélectionné.
Préparation du dépaquetage de .../19-gcc-12_12.3.0-1ubuntu1~22.04_amd64.deb ...
Dépaquetage de gcc-12 (12.3.0-1ubuntu1~22.04) ...
Sélection du paquet libdpkg-perl précédemment désélectionné.
Préparation du dépaquetage de .../20-libdpkg-perl_1.21.1ubuntu2.2_all.deb ...
Dépaquetage de libdpkg-perl (1.21.1ubuntu2.2) ...
Sélection du paquet lto-disabled-list précédemment désélectionné.
Préparation du dépaquetage de .../21-lto-disabled-list_24_all.deb ...
Dépaquetage de lto-disabled-list (24) ...
Sélection du paquet dpkg-dev précédemment désélectionné.
Préparation du dépaquetage de .../22-dpkg-dev_1.21.1ubuntu2.2_all.deb ...
Dépaquetage de dpkg-dev (1.21.1ubuntu2.2) ...
Sélection du paquet libc-dev-bin précédemment désélectionné.
Préparation du dépaquetage de .../23-libc-dev-bin_2.35-0ubuntu3.6_amd64.deb ...
Dépaquetage de libc-dev-bin (2.35-0ubuntu3.6) ...
Sélection du paquet linux-libc-dev:amd64 précédemment désélectionné.
Préparation du dépaquetage de .../24-linux-libc-dev_5.15.0-94.104_amd64.deb ...
Dépaquetage de linux-libc-dev:amd64 (5.15.0-94.104) ...
Sélection du paquet libcrypt-dev:amd64 précédemment désélectionné.
Préparation du dépaquetage de .../25-libcrypt-dev_1%3a4.4.27-1_amd64.deb ...
Dépaquetage de libcrypt-dev:amd64 (1:4.4.27-1) ...
Sélection du paquet rpcsvc-proto précédemment désélectionné.
Préparation du dépaquetage de .../26-rpcsvc-proto_1.4.2-0ubuntu6_amd64.deb ...
Dépaquetage de rpcsvc-proto (1.4.2-0ubuntu6) ...
Sélection du paquet libtirpc-dev:amd64 précédemment désélectionné.
Préparation du dépaquetage de .../27-libtirpc-dev_1.3.2-2ubuntu0.1_amd64.deb ...
Dépaquetage de libtirpc-dev:amd64 (1.3.2-2ubuntu0.1) ...
Sélection du paquet libnsl-dev:amd64 précédemment désélectionné.
Préparation du dépaquetage de .../28-libnsl-dev_1.3.0-2build2_amd64.deb ...
Dépaquetage de libnsl-dev:amd64 (1.3.0-2build2) ...
Sélection du paquet libc6-dev:amd64 précédemment désélectionné.
Préparation du dépaquetage de .../29-libc6-dev_2.35-0ubuntu3.6_amd64.deb ...
Dépaquetage de libc6-dev:amd64 (2.35-0ubuntu3.6) ...
Sélection du paquet libstdc++-11-dev:amd64 précédemment désélectionné.
Préparation du dépaquetage de .../30-libstdc++-11-dev_11.4.0-1ubuntu1~22.04_amd6
4.deb ...
Dépaquetage de libstdc++-11-dev:amd64 (11.4.0-1ubuntu1~22.04) ...
Sélection du paquet g++-11 précédemment désélectionné.
Préparation du dépaquetage de .../31-g++-11_11.4.0-1ubuntu1~22.04_amd64.deb ...
Dépaquetage de g++-11 (11.4.0-1ubuntu1~22.04) ...
Sélection du paquet g++ précédemment désélectionné.
Préparation du dépaquetage de .../32-g++_4%3a11.2.0-1ubuntu1_amd64.deb ...
Dépaquetage de g++ (4:11.2.0-1ubuntu1) ...
Sélection du paquet build-essential précédemment désélectionné.
Préparation du dépaquetage de .../33-build-essential_12.9ubuntu3_amd64.deb ...
Dépaquetage de build-essential (12.9ubuntu3) ...
Sélection du paquet dctrl-tools précédemment désélectionné.
Préparation du dépaquetage de .../34-dctrl-tools_2.24-3build2_amd64.deb ...
Dépaquetage de dctrl-tools (2.24-3build2) ...
Sélection du paquet dkms précédemment désélectionné.
Préparation du dépaquetage de .../35-dkms_2.8.7-2ubuntu2.2_all.deb ...
Dépaquetage de dkms (2.8.7-2ubuntu2.2) ...
Sélection du paquet libfakeroot:amd64 précédemment désélectionné.
Préparation du dépaquetage de .../36-libfakeroot_1.28-1ubuntu1_amd64.deb ...
Dépaquetage de libfakeroot:amd64 (1.28-1ubuntu1) ...
Sélection du paquet fakeroot précédemment désélectionné.
Préparation du dépaquetage de .../37-fakeroot_1.28-1ubuntu1_amd64.deb ...
Dépaquetage de fakeroot (1.28-1ubuntu1) ...
Sélection du paquet iw précédemment désélectionné.
Préparation du dépaquetage de .../38-iw_5.16-1build1_amd64.deb ...
Dépaquetage de iw (5.16-1build1) ...
Sélection du paquet libalgorithm-diff-perl précédemment désélectionné.
Préparation du dépaquetage de .../39-libalgorithm-diff-perl_1.201-1_all.deb ...
Dépaquetage de libalgorithm-diff-perl (1.201-1) ...
Sélection du paquet libalgorithm-diff-xs-perl précédemment désélectionné.
Préparation du dépaquetage de .../40-libalgorithm-diff-xs-perl_0.04-6build3_amd6
4.deb ...
Dépaquetage de libalgorithm-diff-xs-perl (0.04-6build3) ...
Sélection du paquet libalgorithm-merge-perl précédemment désélectionné.
Préparation du dépaquetage de .../41-libalgorithm-merge-perl_0.08-3_all.deb ...
Dépaquetage de libalgorithm-merge-perl (0.08-3) ...
Sélection du paquet libc-devtools précédemment désélectionné.
Préparation du dépaquetage de .../42-libc-devtools_2.35-0ubuntu3.6_amd64.deb ...
Dépaquetage de libc-devtools (2.35-0ubuntu3.6) ...
Sélection du paquet libfile-fcntllock-perl précédemment désélectionné.
Préparation du dépaquetage de .../43-libfile-fcntllock-perl_0.22-3build7_amd64.d
eb ...
Dépaquetage de libfile-fcntllock-perl (0.22-3build7) ...
Sélection du paquet manpages-dev précédemment désélectionné.
Préparation du dépaquetage de .../44-manpages-dev_5.10-1ubuntu1_all.deb ...
Dépaquetage de manpages-dev (5.10-1ubuntu1) ...
Paramétrage de manpages-dev (5.10-1ubuntu1) ...
Paramétrage de lto-disabled-list (24) ...
Paramétrage de cpp-12 (12.3.0-1ubuntu1~22.04) ...
Paramétrage de libfile-fcntllock-perl (0.22-3build7) ...
Paramétrage de libalgorithm-diff-perl (1.201-1) ...
Paramétrage de binutils-common:amd64 (2.38-4ubuntu2.5) ...
Paramétrage de linux-libc-dev:amd64 (5.15.0-94.104) ...
Paramétrage de libctf-nobfd0:amd64 (2.38-4ubuntu2.5) ...
Paramétrage de libfakeroot:amd64 (1.28-1ubuntu1) ...
Paramétrage de libasan6:amd64 (11.4.0-1ubuntu1~22.04) ...
Paramétrage de fakeroot (1.28-1ubuntu1) ...
update-alternatives: utilisation de « /usr/bin/fakeroot-sysv » pour fournir « /u
sr/bin/fakeroot » (fakeroot) en mode automatique
Paramétrage de libtirpc-dev:amd64 (1.3.2-2ubuntu0.1) ...
Paramétrage de rpcsvc-proto (1.4.2-0ubuntu6) ...
Paramétrage de libdpkg-perl (1.21.1ubuntu2.2) ...
Paramétrage de libubsan1:amd64 (12.3.0-1ubuntu1~22.04) ...
Paramétrage de libnsl-dev:amd64 (1.3.0-2build2) ...
Paramétrage de libcrypt-dev:amd64 (1:4.4.27-1) ...
Paramétrage de libasan8:amd64 (12.3.0-1ubuntu1~22.04) ...
Paramétrage de libtsan2:amd64 (12.3.0-1ubuntu1~22.04) ...
Paramétrage de libbinutils:amd64 (2.38-4ubuntu2.5) ...
Paramétrage de iw (5.16-1build1) ...
Paramétrage de libc-dev-bin (2.35-0ubuntu3.6) ...
Paramétrage de libalgorithm-diff-xs-perl (0.04-6build3) ...
Paramétrage de libcc1-0:amd64 (12.3.0-1ubuntu1~22.04) ...
Paramétrage de liblsan0:amd64 (12.3.0-1ubuntu1~22.04) ...
Paramétrage de dctrl-tools (2.24-3build2) ...
Paramétrage de libitm1:amd64 (12.3.0-1ubuntu1~22.04) ...
Paramétrage de libc-devtools (2.35-0ubuntu3.6) ...
Paramétrage de libalgorithm-merge-perl (0.08-3) ...
Paramétrage de libtsan0:amd64 (11.4.0-1ubuntu1~22.04) ...
Paramétrage de libctf0:amd64 (2.38-4ubuntu2.5) ...
Paramétrage de libgcc-12-dev:amd64 (12.3.0-1ubuntu1~22.04) ...
Paramétrage de libgcc-11-dev:amd64 (11.4.0-1ubuntu1~22.04) ...
Paramétrage de libc6-dev:amd64 (2.35-0ubuntu3.6) ...
Paramétrage de binutils-x86-64-linux-gnu (2.38-4ubuntu2.5) ...
Paramétrage de binutils (2.38-4ubuntu2.5) ...
Paramétrage de dpkg-dev (1.21.1ubuntu2.2) ...
Paramétrage de gcc-12 (12.3.0-1ubuntu1~22.04) ...
Paramétrage de libstdc++-11-dev:amd64 (11.4.0-1ubuntu1~22.04) ...
Paramétrage de gcc-11 (11.4.0-1ubuntu1~22.04) ...
Paramétrage de g++-11 (11.4.0-1ubuntu1~22.04) ...
Paramétrage de gcc (4:11.2.0-1ubuntu1) ...
Paramétrage de dkms (2.8.7-2ubuntu2.2) ...
Paramétrage de g++ (4:11.2.0-1ubuntu1) ...
update-alternatives: utilisation de « /usr/bin/g++ » pour fournir « /usr/bin/c++
» (c++) en mode automatique
Paramétrage de build-essential (12.9ubuntu3) ...
Traitement des actions différées (« triggers ») pour man-db (2.10.2-1) ...
Traitement des actions différées (« triggers ») pour libc-bin (2.35-0ubuntu3.6)
...
symeon@symeon-Latitude-E5420:~$ Hors ligne
#21 Le 15/02/2024, à 21:54
- RIMBAUT
Re : pilote rtl8xxxu a remplacé le rtl8198eu RÉSOLU
symeon@symeon-Latitude-E5420:~$ wget -N -t 5 -T 10 https://raw.githubusercontent.com/olivierPrigent/wifiCheck/main/wificheck.sh && chmod 755 wificheck.sh && ./wificheck.sh -v
--2024-02-15 21:52:37-- https://raw.githubusercontent.com/olivierPrigent/wifiCheck/main/wificheck.sh
Résolution de raw.githubusercontent.com (raw.githubusercontent.com)… 2606:50c0:8003::154, 2606:50c0:8000::154, 2606:50c0:8001::154, ...
Connexion à raw.githubusercontent.com (raw.githubusercontent.com)|2606:50c0:8003::154|:443… échec : Connexion terminée par expiration du délai d'attente.
Connexion à raw.githubusercontent.com (raw.githubusercontent.com)|2606:50c0:8000::154|:443… connecté.
requête HTTP transmise, en attente de la réponse… 200 OK
Taille : 12066 (12K) [text/plain]
Enregistre : ‘wificheck.sh’
wificheck.sh 100%[===================>] 11,78K --.-KB/s ds 0,007s
En-tête de dernière modification manquant — horodatage arrêté.
2024-02-15 21:52:48 (1,72 MB/s) - ‘wificheck.sh’ enregistré [12066/12066]
[sudo] Mot de passe de symeon :
####################################################################
Le fichier wificheck.log a été crée dans /home/symeon
Vous n'avez plus qu'à copier/coller son contenu entier sur le forum
accès →→ /home/symeon/wificheck.log
####################################################################
symeon@symeon-Latitude-E5420:~$ Hors ligne
#22 Le 15/02/2024, à 21:54
- RIMBAUT
Re : pilote rtl8xxxu a remplacé le rtl8198eu RÉSOLU
[code]
###############################################
########### Wifi Check ##################
###############################################
############ Date #####################
2024-02-15
##### Current kernel, release, desktop ######
Current Kernel : 6.5.0-17-generic
Release Description: Ubuntu 22.04.3 LTS
Current Desktop : XFCE
####### lspci -k -nn | grep -A 3 -i net ######
02:00.0 Network controller [0280]: Broadcom Inc. and subsidiaries BCM4313 802.11bgn Wireless Network Adapter [14e4:4727] (rev 01)
Subsystem: Dell Inspiron M5010 / XPS 8300 [1028:0010]
Kernel driver in use: bcma-pci-bridge
Kernel modules: bcma
--
0a:00.0 Ethernet controller [0200]: Broadcom Inc. and subsidiaries NetXtreme BCM5761 Gigabit Ethernet PCIe [14e4:1681] (rev 10)
Subsystem: Dell NetXtreme BCM5761 Gigabit Ethernet PCIe [1028:049b]
Kernel driver in use: tg3
Kernel modules: tg3
######## sudo lshw -C network #########
*-network
description: Interface réseau sans fil
produit: BCM4313 802.11bgn Wireless Network Adapter
fabricant: Broadcom Inc. and subsidiaries
identifiant matériel: 0
information bus: pci@0000:02:00.0
nom logique: wlp2s0b1
version: 01
numéro de série: 38:59:f9:8d:8a:86
bits: 64 bits
horloge: 33MHz
fonctionnalités: pm msi pciexpress bus_master cap_list ethernet physical wireless
configuration : broadcast=yes driver=brcmsmac driverversion=6.5.0-17-generic firmware=610.812 latency=0 link=yes multicast=yes wireless=IEEE 802.11
ressources : irq:17 mémoire:93c00000-93c03fff
*-network
description: Ethernet interface
produit: NetXtreme BCM5761 Gigabit Ethernet PCIe
fabricant: Broadcom Inc. and subsidiaries
identifiant matériel: 0
information bus: pci@0000:0a:00.0
nom logique: enp10s0
version: 10
numéro de série: d0:67:e5:33:ce:ff
capacité: 1Gbit/s
bits: 64 bits
horloge: 33MHz
fonctionnalités: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
configuration : autonegotiation=on broadcast=yes driver=tg3 driverversion=6.5.0-17-generic firmware=5761-v3.78 latency=0 link=no multicast=yes port=twisted pair
ressources : irq:27 mémoire:92010000-9201ffff mémoire:92000000-9200ffff
*-network:0 DÉSACTIVÉ
description: Ethernet interface
identifiant matériel: a
information bus: usb@1:1.6
nom logique: wwx028037ec0200
numéro de série: 02:80:37:ec:02:00
fonctionnalités: ethernet physical
configuration : autonegotiation=off broadcast=yes driver=cdc_ncm driverversion=6.5.0-17-generic duplex=half firmware=Mobile Broadband Network Device link=no multicast=yes port=twisted pair
*-network:1
description: Interface réseau sans fil
identifiant matériel: b
information bus: usb@2:1.3
nom logique: wlx00e04c16cfec
numéro de série: 00:e0:4c:16:cf:ec
fonctionnalités: ethernet physical wireless
configuration : broadcast=yes driver=rtl8xxxu driverversion=6.5.0-17-generic firmware=N/A ip=192.168.1.12 link=yes multicast=yes wireless=IEEE 802.11
################ lsusb ################
Bus 002 Device 005: ID 413c:8187 Dell Computer Corp. DW375 Bluetooth Module
Bus 002 Device 007: ID 248a:00da Maxxter Wireless Receiver
Bus 002 Device 006: ID 1ea7:0066 SHARKOON Technologies GmbH [Mediatrack Edge Mini Keyboard]
Bus 002 Device 004: ID 05e3:0608 Genesys Logic, Inc. Hub
Bus 002 Device 003: ID 0bda:818b Realtek Semiconductor Corp. RTL8192EU 802.11b/g/n WLAN Adapter
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 413c:818d Dell Computer Corp. DW5550
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
####### lsmod | grep <wifi_modules> #######
Module Size Used by
b43 577536 0
cordic 12288 2 b43,brcmsmac
mac80211 1720320 3 b43,rtl8xxxu,brcmsmac
cfg80211 1318912 4 b43,mac80211,rtl8xxxu,brcmsmac
ssb 102400 1 b43
bcma 86016 2 b43,brcmsmac
################# dkms status ###############
######### mokutil --sb-state #############
EFI variables are not supported on this system
########## sudo rfkill list #############
0: hci0: Bluetooth
Soft blocked: no
Hard blocked: no
1: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no
2: phy1: Wireless LAN
Soft blocked: no
Hard blocked: no
3: dell-wifi: Wireless LAN
Soft blocked: no
Hard blocked: no
4: dell-bluetooth: Bluetooth
Soft blocked: no
Hard blocked: no
5: dell-wwan: Wireless WAN
Soft blocked: no
Hard blocked: no
################ ip a ###################
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: enp10s0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group default qlen 1000
link/ether d0:67:e5:33:ce:ff brd ff:ff:ff:ff:ff:ff
3: wwx028037ec0200: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 02:80:37:ec:02:00 brd ff:ff:ff:ff:ff:ff
4: wlx00e04c16cfec: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
link/ether 00:e0:4c:16:cf:ec brd ff:ff:ff:ff:ff:ff
inet 192.168.1.12/24 brd 192.168.1.255 scope global dynamic noprefixroute wlx00e04c16cfec
valid_lft 85855sec preferred_lft 85855sec
inet6 2a01:cb0c:840e:ff00:3a4b:bb51:96e1:3c78/64 scope global temporary dynamic
valid_lft 86397sec preferred_lft 597sec
inet6 2a01:cb0c:840e:ff00:8fe5:2ee3:e777:7419/64 scope global dynamic mngtmpaddr noprefixroute
valid_lft 86397sec preferred_lft 597sec
inet6 fe80::89cc:45ed:31f9:cf05/64 scope link noprefixroute
valid_lft forever preferred_lft forever
5: wlp2s0b1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
link/ether 38:59:f9:8d:8a:86 brd ff:ff:ff:ff:ff:ff
inet6 2a01:cb0c:840e:ff00:9499:1275:612f:fc23/64 scope global temporary dynamic
valid_lft 86397sec preferred_lft 597sec
inet6 2a01:cb0c:840e:ff00:be5f:2014:cd92:9002/64 scope global dynamic mngtmpaddr noprefixroute
valid_lft 86397sec preferred_lft 597sec
inet6 fe80::7fde:6794:d3f9:8b0d/64 scope link noprefixroute
valid_lft forever preferred_lft forever
################ ping no-DNS ###################
ping gateway ipv4 : ok
ping gateway ipv6 : mauvais
ping cloudflare ipv4 : ok
ping cloudflare ipv6 : mauvais
######### resolvectl | grep Server #########
Current DNS Server: 192.168.1.1
DNS Servers: 192.168.1.1 2a01:cb0c:840e:ff00:aeb6:87ff:fe74:2ebc
Current DNS Server: 2a01:cb0c:840e:ff00:aeb6:87ff:fe74:2ebc
DNS Servers: 2a01:cb0c:840e:ff00:aeb6:87ff:fe74:2ebc
########### sudo ufw status #############
État : inactif
###### cat /etc/network/interfaces #######
# ce fichier est obsolète sauf si vous savez ce que vous faîtes #
cat: /etc/network/interfaces: Aucun fichier ou dossier de ce type
########### nmcli dev show ##############
DEVICE TYPE STATE CONNECTION
wlx00e04c16cfec wifi connecté Livebox-2EBC 1
wlp2s0b1 wifi connecté Livebox-2EBC
7C:A4:49:5B:32:43 bt déconnecté --
enp10s0 ethernet indisponible --
ttyACM1 gsm indisponible --
lo loopback non-géré --
########### nmcli dev wifi ##############
IN-USE BSSID SSID MODE CHAN RATE SIGNAL BARS SECURITY
* AC:B6:87:74:2E:BC Livebox-2EBC Infra 11 130 Mbit/s 48 ▂▄__ WPA2
30:7C:B2:3C:D7:BF Livebox-D7BF Infra 6 130 Mbit/s 20 ▂___ WPA1 WPA2
B6:36:0B:F1:88:05 Redmi A1 Infra 1 117 Mbit/s 7 ▂___ WPA2 WPA3
44:D4:53:95:5C:F8 Livebox-7C40 Infra 11 405 Mbit/s 7 ▂___ WPA2
70:FC:8F:B8:CB:94 Freebox-A344B1 Infra 11 195 Mbit/s 7 ▂___ WPA2
EC:6C:9A:B4:10:8A Livebox-108A Infra 11 130 Mbit/s 7 ▂___ WPA2
IN-USE BSSID SSID MODE CHAN RATE SIGNAL BARS SECURITY
* AC:B6:87:74:2E:BC Livebox-2EBC Infra 11 130 Mbit/s 34 ▂▄__ WPA2
############## iw dev ####################
phy#1
Interface wlp2s0b1
ifindex 5
wdev 0x100000001
addr 38:59:f9:8d:8a:86
ssid Livebox-2EBC
type managed
channel 11 (2462 MHz), width: 20 MHz, center1: 2462 MHz
txpower 19.00 dBm
multicast TXQ:
qsz-byt qsz-pkt flows drops marks overlmt hashcol tx-bytes tx-packets
0 0 0 0 0 0 0 0 0
phy#0
Interface wlx00e04c16cfec
ifindex 4
wdev 0x1
addr 00:e0:4c:16:cf:ec
ssid Livebox-2EBC
type managed
channel 11 (2462 MHz), width: 20 MHz, center1: 2462 MHz
txpower 20.00 dBm
multicast TXQ:
qsz-byt qsz-pkt flows drops marks overlmt hashcol tx-bytes tx-packets
0 0 0 0 0 0 0 0 0
######### iw dev wlp2s0b1 link #############
Connected to ac:b6:87:74:2e:bc (on wlp2s0b1)
SSID: Livebox-2EBC
freq: 2462
RX: 1956310 bytes (12843 packets)
TX: 148565 bytes (1553 packets)
signal: -82 dBm
rx bitrate: 12.0 MBit/s
tx bitrate: 6.5 MBit/s MCS 0
bss flags: short-preamble short-slot-time
dtim period: 3
beacon int: 100
######## iw dev wlp2s0b1 station dump ###########
Station ac:b6:87:74:2e:bc (on wlp2s0b1)
inactive time: 3040 ms
rx bytes: 1956310
rx packets: 12843
tx bytes: 148565
tx packets: 1553
tx retries: 182
tx failed: 957
beacon loss: 0
beacon rx: 6078
rx drop misc: 11
signal: -82 dBm
signal avg: -83 dBm
beacon signal avg: -82 dBm
tx bitrate: 6.5 MBit/s MCS 0
tx duration: 0 us
rx bitrate: 12.0 MBit/s
rx duration: 0 us
authorized: yes
authenticated: yes
associated: yes
preamble: long
WMM/WME: yes
MFP: no
TDLS peer: no
DTIM period: 3
beacon interval:100
short preamble: yes
short slot time:yes
connected time: 757 seconds
associated at [boottime]: 56.445s
associated at: 1708029637709 ms
current time: 1708030395264 ms
######## iw list ###########
Wiphy phy1
wiphy index: 1
max # scan SSIDs: 4
max scan IEs length: 2257 bytes
max # sched scan SSIDs: 0
max # match sets: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports RSN-IBSS.
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP-128 (00-0f-ac:4)
* CCMP-256 (00-0f-ac:10)
* GCMP-128 (00-0f-ac:8)
* GCMP-256 (00-0f-ac:9)
Available Antennas: TX 0 RX 0
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
Band 1:
Capabilities: 0x7c
HT20
SM Power Save disabled
RX Greenfield
RX HT20 SGI
RX HT40 SGI
No RX STBC
Max AMSDU length: 3839 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT Max RX data rate: 72 Mbps
HT TX/RX MCS rate indexes supported: 0-7
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps (short preamble supported)
* 5.5 Mbps (short preamble supported)
* 11.0 Mbps (short preamble supported)
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 2412 MHz [1] (19.0 dBm)
* 2417 MHz [2] (19.0 dBm)
* 2422 MHz [3] (19.0 dBm)
* 2427 MHz [4] (19.0 dBm)
* 2432 MHz [5] (19.0 dBm)
* 2437 MHz [6] (19.0 dBm)
* 2442 MHz [7] (19.0 dBm)
* 2447 MHz [8] (19.0 dBm)
* 2452 MHz [9] (19.0 dBm)
* 2457 MHz [10] (19.0 dBm)
* 2462 MHz [11] (19.0 dBm)
* 2467 MHz [12] (19.0 dBm)
* 2472 MHz [13] (19.0 dBm)
* 2484 MHz [14] (disabled)
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* new_station
* new_mpath
* set_mesh_config
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* join_mesh
* remain_on_channel
* set_tx_bitrate_mask
* frame
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* probe_client
* set_noack_map
* register_beacons
* start_p2p_device
* set_mcast_rate
* connect
* disconnect
* set_qos_map
* set_multicast_to_unicast
software interface modes (can always be added):
* AP/VLAN
* monitor
interface combinations are not supported
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
Device supports SAE with AUTHENTICATE command
Device supports low priority scan.
Device supports scan flush.
Device supports AP scan.
Device supports per-vif TX power setting
Driver supports full state transitions for AP/GO clients
Driver supports a userspace MPM
Device supports configuring vdev MAC-addr on create.
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0x40 0xb0 0xc0 0xd0
* managed: 0x40 0xb0 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* mesh point: 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-device: 0x40 0xd0
Supported extended features:
* [ RRM ]: RRM
* [ FILS_STA ]: STA FILS (Fast Initial Link Setup)
* [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
* [ SCAN_RANDOM_SN ]: use random sequence numbers in scans
* [ SCAN_MIN_PREQ_CONTENT ]: use probe request with only rate IEs in scans
* [ CAN_REPLACE_PTK0 ]: can safely replace PTK 0 when rekeying
* [ EXT_KEY_ID ]: Extended Key ID support
* [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
* [ DEL_IBSS_STA ]: deletion of IBSS station support
* [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
* [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support
Wiphy phy0
wiphy index: 0
max # scan SSIDs: 4
max scan IEs length: 2257 bytes
max # sched scan SSIDs: 0
max # match sets: 0
RTS threshold: 2347
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP-128 (00-0f-ac:4)
* CCMP-256 (00-0f-ac:10)
* GCMP-128 (00-0f-ac:8)
* GCMP-256 (00-0f-ac:9)
Available Antennas: TX 0x3 RX 0x3
Configured Antennas: TX 0x3 RX 0x3
Supported interface modes:
* managed
* monitor
Band 1:
Capabilities: 0x6c
HT20
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
No RX STBC
Max AMSDU length: 3839 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 16 usec (0x07)
HT TX/RX MCS rate indexes supported: 0-15, 32
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps
* 5.5 Mbps
* 11.0 Mbps
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 2412 MHz [1] (20.0 dBm)
* 2417 MHz [2] (20.0 dBm)
* 2422 MHz [3] (20.0 dBm)
* 2427 MHz [4] (20.0 dBm)
* 2432 MHz [5] (20.0 dBm)
* 2437 MHz [6] (20.0 dBm)
* 2442 MHz [7] (20.0 dBm)
* 2447 MHz [8] (20.0 dBm)
* 2452 MHz [9] (20.0 dBm)
* 2457 MHz [10] (20.0 dBm)
* 2462 MHz [11] (20.0 dBm)
* 2467 MHz [12] (20.0 dBm)
* 2472 MHz [13] (20.0 dBm)
* 2484 MHz [14] (disabled)
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* new_station
* new_mpath
* set_mesh_config
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* join_mesh
* remain_on_channel
* set_tx_bitrate_mask
* frame
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* probe_client
* set_noack_map
* register_beacons
* start_p2p_device
* set_mcast_rate
* connect
* disconnect
* set_qos_map
* set_multicast_to_unicast
software interface modes (can always be added):
* monitor
interface combinations are not supported
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
Device supports SAE with AUTHENTICATE command
Device supports low priority scan.
Device supports scan flush.
Device supports AP scan.
Device supports per-vif TX power setting
Driver supports full state transitions for AP/GO clients
Driver supports a userspace MPM
Device supports configuring vdev MAC-addr on create.
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0x40 0xb0 0xc0 0xd0
* managed: 0x40 0xb0 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* mesh point: 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-device: 0x40 0xd0
Supported extended features:
* [ RRM ]: RRM
* [ FILS_STA ]: STA FILS (Fast Initial Link Setup)
* [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
* [ SCAN_RANDOM_SN ]: use random sequence numbers in scans
* [ SCAN_MIN_PREQ_CONTENT ]: use probe request with only rate IEs in scans
* [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
* [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
* [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support
############ iw dev wlp2s0b1 scan ############
BSS ac:b6:87:74:2e:bc(on wlp2s0b1) -- associated
TSF: 1404789134154 usec (16d, 06:13:09)
freq: 2462
beacon interval: 100 TUs
capability: ESS Privacy SpectrumMgmt ShortSlotTime RadioMeasure (0x1511)
signal: -86.00 dBm
last seen: 168 ms ago
Information elements from Probe Response frame:
SSID: Livebox-2EBC
Supported rates: 1.0* 2.0* 5.5* 11.0* 18.0 24.0 36.0 54.0
DS Parameter set: channel 11
Country: FR Environment: Indoor/Outdoor
Channels [1 - 13] @ 20 dBm
Power constraint: 0 dB
TPC report: TX power: 17 dBm
ERP: <no flags>
Extended supported rates: 6.0 9.0 12.0 48.0
RSN: * Version: 1
* Group cipher: CCMP
* Pairwise ciphers: CCMP
* Authentication suites: PSK
* Capabilities: 16-PTKSA-RC 1-GTKSA-RC (0x000c)
BSS Load:
* station count: 3
* channel utilisation: 7/255
* available admission capacity: 0 [*32us]
Measurement Pilot Transmission:
* interval: 0 TUs
RM enabled capabilities:
Capabilities: 0x33 0x4f 0x01 0x00 0x00
Link Measurement
Neighbor Report
Beacon Passive Measurement
Beacon Active Measurement
Frame Measurement
Channel Load
Noise Histogram Measurement
Statistics Measurement
Transmit Stream/Category Measurement
AP Channel Report
Nonoperating Channel Max Measurement Duration: 0
Measurement Pilot Capability: 0
HT capabilities:
Capabilities: 0x9ac
HT20
SM Power Save disabled
RX HT20 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 7935 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT RX MCS rate indexes supported: 0-15
HT TX MCS rate indexes are undefined
HT operation:
* primary channel: 11
* secondary channel offset: no secondary
* STA channel width: 20 MHz
* RIFS: 1
* HT protection: no
* non-GF present: 1
* OBSS non-GF present: 0
* dual beacon: 0
* dual CTS protection: 0
* STBC beacon: 0
* L-SIG TXOP Prot: 0
* PCO active: 0
* PCO phase: 0
Extended capabilities:
* Extended Channel Switching
* BSS Transition
* Operating Mode Notification
WPS: * Version: 1.0
* Wi-Fi Protected Setup State: 2 (Configured)
* Response Type: 3 (AP)
* UUID: 41434236-3837-f734-f245-424341434236
* Manufacturer: Arcadyan
* Model: ArcadyanLBFIBRE_OFR
* Model Number: AR_LBF_2.1
* Serial Number: JA22228FF
* Primary Device Type: 6-0050f204-1
* Device name: Livebox Fibre
* Config methods: Ethernet, Label
* RF Bands: 0x1
* Version2: 2.0
WMM: * Parameter version 1
* BE: CW 15-1023, AIFSN 3
* BK: CW 15-1023, AIFSN 7
* VI: CW 7-15, AIFSN 2, TXOP 3008 usec
* VO: CW 3-7, AIFSN 2, TXOP 1504 usec
############## iw dev ####################
phy#1
Interface wlp2s0b1
ifindex 5
wdev 0x100000001
addr 38:59:f9:8d:8a:86
ssid Livebox-2EBC
type managed
channel 11 (2462 MHz), width: 20 MHz, center1: 2462 MHz
txpower 19.00 dBm
multicast TXQ:
qsz-byt qsz-pkt flows drops marks overlmt hashcol tx-bytes tx-packets
0 0 0 0 0 0 0 0 0
phy#0
Interface wlx00e04c16cfec
ifindex 4
wdev 0x1
addr 00:e0:4c:16:cf:ec
ssid Livebox-2EBC
type managed
channel 11 (2462 MHz), width: 20 MHz, center1: 2462 MHz
txpower 20.00 dBm
multicast TXQ:
qsz-byt qsz-pkt flows drops marks overlmt hashcol tx-bytes tx-packets
0 0 0 0 0 0 0 0 0
######### iw dev wlx00e04c16cfec link #############
Connected to ac:b6:87:74:2e:bc (on wlx00e04c16cfec)
SSID: Livebox-2EBC
freq: 2462
RX: 103864382 bytes (78053 packets)
TX: 3541515 bytes (35785 packets)
signal: -72 dBm
rx bitrate: 39.0 MBit/s MCS 10
tx bitrate: 52.0 MBit/s MCS 11
bss flags: short-preamble short-slot-time
dtim period: 3
beacon int: 100
######## iw dev wlx00e04c16cfec station dump ###########
Station ac:b6:87:74:2e:bc (on wlx00e04c16cfec)
inactive time: 600 ms
rx bytes: 103864382
rx packets: 78053
tx bytes: 3541515
tx packets: 35785
tx retries: 0
tx failed: 0
beacon loss: 0
beacon rx: 5103
rx drop misc: 14
signal: -72 dBm
signal avg: -69 dBm
beacon signal avg: -71 dBm
tx bitrate: 52.0 MBit/s MCS 11
tx duration: 0 us
rx bitrate: 39.0 MBit/s MCS 10
rx duration: 0 us
authorized: yes
authenticated: yes
associated: yes
preamble: long
WMM/WME: yes
MFP: no
TDLS peer: no
DTIM period: 3
beacon interval:100
short preamble: yes
short slot time:yes
connected time: 552 seconds
associated at [boottime]: 264.878s
associated at: 1708029846142 ms
current time: 1708030397383 ms
######## iw list ###########
Wiphy phy1
wiphy index: 1
max # scan SSIDs: 4
max scan IEs length: 2257 bytes
max # sched scan SSIDs: 0
max # match sets: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports RSN-IBSS.
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP-128 (00-0f-ac:4)
* CCMP-256 (00-0f-ac:10)
* GCMP-128 (00-0f-ac:8)
* GCMP-256 (00-0f-ac:9)
Available Antennas: TX 0 RX 0
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
Band 1:
Capabilities: 0x7c
HT20
SM Power Save disabled
RX Greenfield
RX HT20 SGI
RX HT40 SGI
No RX STBC
Max AMSDU length: 3839 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT Max RX data rate: 72 Mbps
HT TX/RX MCS rate indexes supported: 0-7
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps (short preamble supported)
* 5.5 Mbps (short preamble supported)
* 11.0 Mbps (short preamble supported)
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 2412 MHz [1] (19.0 dBm)
* 2417 MHz [2] (19.0 dBm)
* 2422 MHz [3] (19.0 dBm)
* 2427 MHz [4] (19.0 dBm)
* 2432 MHz [5] (19.0 dBm)
* 2437 MHz [6] (19.0 dBm)
* 2442 MHz [7] (19.0 dBm)
* 2447 MHz [8] (19.0 dBm)
* 2452 MHz [9] (19.0 dBm)
* 2457 MHz [10] (19.0 dBm)
* 2462 MHz [11] (19.0 dBm)
* 2467 MHz [12] (19.0 dBm)
* 2472 MHz [13] (19.0 dBm)
* 2484 MHz [14] (disabled)
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* new_station
* new_mpath
* set_mesh_config
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* join_mesh
* remain_on_channel
* set_tx_bitrate_mask
* frame
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* probe_client
* set_noack_map
* register_beacons
* start_p2p_device
* set_mcast_rate
* connect
* disconnect
* set_qos_map
* set_multicast_to_unicast
software interface modes (can always be added):
* AP/VLAN
* monitor
interface combinations are not supported
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
Device supports SAE with AUTHENTICATE command
Device supports low priority scan.
Device supports scan flush.
Device supports AP scan.
Device supports per-vif TX power setting
Driver supports full state transitions for AP/GO clients
Driver supports a userspace MPM
Device supports configuring vdev MAC-addr on create.
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0x40 0xb0 0xc0 0xd0
* managed: 0x40 0xb0 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* mesh point: 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-device: 0x40 0xd0
Supported extended features:
* [ RRM ]: RRM
* [ FILS_STA ]: STA FILS (Fast Initial Link Setup)
* [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
* [ SCAN_RANDOM_SN ]: use random sequence numbers in scans
* [ SCAN_MIN_PREQ_CONTENT ]: use probe request with only rate IEs in scans
* [ CAN_REPLACE_PTK0 ]: can safely replace PTK 0 when rekeying
* [ EXT_KEY_ID ]: Extended Key ID support
* [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
* [ DEL_IBSS_STA ]: deletion of IBSS station support
* [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
* [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support
Wiphy phy0
wiphy index: 0
max # scan SSIDs: 4
max scan IEs length: 2257 bytes
max # sched scan SSIDs: 0
max # match sets: 0
RTS threshold: 2347
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP-128 (00-0f-ac:4)
* CCMP-256 (00-0f-ac:10)
* GCMP-128 (00-0f-ac:8)
* GCMP-256 (00-0f-ac:9)
Available Antennas: TX 0x3 RX 0x3
Configured Antennas: TX 0x3 RX 0x3
Supported interface modes:
* managed
* monitor
Band 1:
Capabilities: 0x6c
HT20
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
No RX STBC
Max AMSDU length: 3839 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 16 usec (0x07)
HT TX/RX MCS rate indexes supported: 0-15, 32
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps
* 5.5 Mbps
* 11.0 Mbps
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 2412 MHz [1] (20.0 dBm)
* 2417 MHz [2] (20.0 dBm)
* 2422 MHz [3] (20.0 dBm)
* 2427 MHz [4] (20.0 dBm)
* 2432 MHz [5] (20.0 dBm)
* 2437 MHz [6] (20.0 dBm)
* 2442 MHz [7] (20.0 dBm)
* 2447 MHz [8] (20.0 dBm)
* 2452 MHz [9] (20.0 dBm)
* 2457 MHz [10] (20.0 dBm)
* 2462 MHz [11] (20.0 dBm)
* 2467 MHz [12] (20.0 dBm)
* 2472 MHz [13] (20.0 dBm)
* 2484 MHz [14] (disabled)
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* new_station
* new_mpath
* set_mesh_config
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* join_mesh
* remain_on_channel
* set_tx_bitrate_mask
* frame
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* probe_client
* set_noack_map
* register_beacons
* start_p2p_device
* set_mcast_rate
* connect
* disconnect
* set_qos_map
* set_multicast_to_unicast
software interface modes (can always be added):
* monitor
interface combinations are not supported
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
Device supports SAE with AUTHENTICATE command
Device supports low priority scan.
Device supports scan flush.
Device supports AP scan.
Device supports per-vif TX power setting
Driver supports full state transitions for AP/GO clients
Driver supports a userspace MPM
Device supports configuring vdev MAC-addr on create.
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0x40 0xb0 0xc0 0xd0
* managed: 0x40 0xb0 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* mesh point: 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-device: 0x40 0xd0
Supported extended features:
* [ RRM ]: RRM
* [ FILS_STA ]: STA FILS (Fast Initial Link Setup)
* [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
* [ SCAN_RANDOM_SN ]: use random sequence numbers in scans
* [ SCAN_MIN_PREQ_CONTENT ]: use probe request with only rate IEs in scans
* [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
* [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
* [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support
############ iw dev wlx00e04c16cfec scan ############
BSS ac:b6:87:74:2e:bc(on wlx00e04c16cfec) -- associated
TSF: 1404794298687 usec (16d, 06:13:14)
freq: 2462
beacon interval: 100 TUs
capability: ESS Privacy SpectrumMgmt ShortSlotTime RadioMeasure (0x1511)
signal: -72.00 dBm
last seen: 44 ms ago
Information elements from Probe Response frame:
SSID: Livebox-2EBC
Supported rates: 1.0* 2.0* 5.5* 11.0* 18.0 24.0 36.0 54.0
DS Parameter set: channel 11
Country: FR Environment: Indoor/Outdoor
Channels [1 - 13] @ 20 dBm
Power constraint: 0 dB
TPC report: TX power: 17 dBm
ERP: <no flags>
Extended supported rates: 6.0 9.0 12.0 48.0
RSN: * Version: 1
* Group cipher: CCMP
* Pairwise ciphers: CCMP
* Authentication suites: PSK
* Capabilities: 16-PTKSA-RC 1-GTKSA-RC (0x000c)
BSS Load:
* station count: 3
* channel utilisation: 12/255
* available admission capacity: 0 [*32us]
Measurement Pilot Transmission:
* interval: 0 TUs
RM enabled capabilities:
Capabilities: 0x33 0x4f 0x01 0x00 0x00
Link Measurement
Neighbor Report
Beacon Passive Measurement
Beacon Active Measurement
Frame Measurement
Channel Load
Noise Histogram Measurement
Statistics Measurement
Transmit Stream/Category Measurement
AP Channel Report
Nonoperating Channel Max Measurement Duration: 0
Measurement Pilot Capability: 0
HT capabilities:
Capabilities: 0x9ac
HT20
SM Power Save disabled
RX HT20 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 7935 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT RX MCS rate indexes supported: 0-15
HT TX MCS rate indexes are undefined
HT operation:
* primary channel: 11
* secondary channel offset: no secondary
* STA channel width: 20 MHz
* RIFS: 1
* HT protection: no
* non-GF present: 1
* OBSS non-GF present: 0
* dual beacon: 0
* dual CTS protection: 0
* STBC beacon: 0
* L-SIG TXOP Prot: 0
* PCO active: 0
* PCO phase: 0
Extended capabilities:
* Extended Channel Switching
* BSS Transition
* Operating Mode Notification
WPS: * Version: 1.0
* Wi-Fi Protected Setup State: 2 (Configured)
* Response Type: 3 (AP)
* UUID: 41434236-3837-f734-f245-424341434236
* Manufacturer: Arcadyan
* Model: ArcadyanLBFIBRE_OFR
* Model Number: AR_LBF_2.1
* Serial Number: JA22228FF
* Primary Device Type: 6-0050f204-1
* Device name: Livebox Fibre
* Config methods: Ethernet, Label
* RF Bands: 0x1
* Version2: 2.0
WMM: * Parameter version 1
* BE: CW 15-1023, AIFSN 3
* BK: CW 15-1023, AIFSN 7
* VI: CW 7-15, AIFSN 2, TXOP 3008 usec
* VO: CW 3-7, AIFSN 2, TXOP 1504 usec
BSS 70:fc:8f:b8:cb:94(on wlx00e04c16cfec)
TSF: 13043681631 usec (0d, 03:37:23)
freq: 2462
beacon interval: 120 TUs
capability: ESS Privacy ShortSlotTime RadioMeasure (0x1411)
signal: -96.00 dBm
last seen: 1356 ms ago
SSID: Freebox-A344B1
Supported rates: 1.0* 2.0* 5.5* 11.0* 6.0 9.0 12.0 18.0
DS Parameter set: channel 11
TIM: DTIM Count 1 DTIM Period 2 Bitmap Control 0x0 Bitmap[0] 0x0
ERP: Barker_Preamble_Mode
Extended supported rates: 24.0 36.0 48.0 54.0
RSN: * Version: 1
* Group cipher: CCMP
* Pairwise ciphers: CCMP
* Authentication suites: PSK
* Capabilities: 16-PTKSA-RC 1-GTKSA-RC (0x000c)
BSS Load:
* station count: 0
* channel utilisation: 13/255
* available admission capacity: 0 [*32us]
RM enabled capabilities:
Capabilities: 0x72 0x00 0x00 0x00 0x00
Neighbor Report
Beacon Passive Measurement
Beacon Active Measurement
Beacon Table Measurement
Nonoperating Channel Max Measurement Duration: 0
Measurement Pilot Capability: 0
HT capabilities:
Capabilities: 0xec
HT20
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
No RX STBC
Max AMSDU length: 3839 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: No restriction (0x00)
HT TX/RX MCS rate indexes supported: 0-23, 32
HT operation:
* primary channel: 11
* secondary channel offset: no secondary
* STA channel width: 20 MHz
* RIFS: 0
* HT protection: no
* non-GF present: 0
* OBSS non-GF present: 0
* dual beacon: 0
* dual CTS protection: 0
* STBC beacon: 0
* L-SIG TXOP Prot: 0
* PCO active: 0
* PCO phase: 0
Extended capabilities:
* BSS Transition
* SSID List
* Operating Mode Notification
WMM: * Parameter version 1
* BE: CW 15-1023, AIFSN 3
* BK: CW 15-1023, AIFSN 7
* VI: CW 7-15, AIFSN 2, TXOP 3008 usec
* VO: CW 3-7, AIFSN 2, TXOP 1504 usec
BSS ec:6c:9a:b4:10:8a(on wlx00e04c16cfec)
TSF: 94706995600 usec (1d, 02:18:26)
freq: 2462
beacon interval: 100 TUs
capability: ESS Privacy SpectrumMgmt ShortSlotTime RadioMeasure (0x1511)
signal: -96.00 dBm
last seen: 2304 ms ago
SSID: Livebox-108A
Supported rates: 1.0* 2.0* 5.5* 11.0* 18.0 24.0 36.0 54.0
DS Parameter set: channel 11
TIM: DTIM Count 1 DTIM Period 3 Bitmap Control 0x0 Bitmap[0] 0x0
Country: FR Environment: Indoor/Outdoor
Channels [1 - 13] @ 20 dBm
Power constraint: 0 dB
TPC report: TX power: 17 dBm
ERP: Barker_Preamble_Mode
Extended supported rates: 6.0 9.0 12.0 48.0
RSN: * Version: 1
* Group cipher: CCMP
* Pairwise ciphers: CCMP
* Authentication suites: PSK
* Capabilities: 16-PTKSA-RC 1-GTKSA-RC (0x000c)
BSS Load:
* station count: 1
* channel utilisation: 9/255
* available admission capacity: 0 [*32us]
Measurement Pilot Transmission:
* interval: 0 TUs
RM enabled capabilities:
Capabilities: 0x33 0x4f 0x01 0x00 0x00
Link Measurement
Neighbor Report
Beacon Passive Measurement
Beacon Active Measurement
Frame Measurement
Channel Load
Noise Histogram Measurement
Statistics Measurement
Transmit Stream/Category Measurement
AP Channel Report
Nonoperating Channel Max Measurement Duration: 0
Measurement Pilot Capability: 0
HT capabilities:
Capabilities: 0x9ac
HT20
SM Power Save disabled
RX HT20 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 7935 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT RX MCS rate indexes supported: 0-15
HT TX MCS rate indexes are undefined
HT operation:
* primary channel: 11
* secondary channel offset: no secondary
* STA channel width: 20 MHz
* RIFS: 1
* HT protection: no
* non-GF present: 1
* OBSS non-GF present: 0
* dual beacon: 0
* dual CTS protection: 0
* STBC beacon: 0
* L-SIG TXOP Prot: 0
* PCO active: 0
* PCO phase: 0
Extended capabilities:
* Extended Channel Switching
* BSS Transition
* Operating Mode Notification
WPS: * Version: 1.0
* Wi-Fi Protected Setup State: 2 (Configured)
* UUID: 45433643-3941-f234-f130-384145433643
* RF Bands: 0x1
* Device name: Livebox Fibre
* Version2: 2.0
WMM: * Parameter version 1
* BE: CW 15-1023, AIFSN 3
* BK: CW 15-1023, AIFSN 7
* VI: CW 7-15, AIFSN 2, TXOP 3008 usec
* VO: CW 3-7, AIFSN 2, TXOP 1504 usec
BSS 30:7c:b2:3c:d7:bf(on wlx00e04c16cfec)
TSF: 445035442481 usec (5d, 03:37:15)
freq: 2437
beacon interval: 100 TUs
capability: ESS Privacy ShortPreamble ShortSlotTime (0x0431)
signal: -96.00 dBm
last seen: 2400 ms ago
Information elements from Probe Response frame:
SSID: Livebox-D7BF
Supported rates: 1.0* 2.0* 5.5* 11.0* 6.0 9.0 12.0 18.0
DS Parameter set: channel 6
Country: FR Environment: Indoor/Outdoor
Channels [1 - 13] @ 20 dBm
ERP: <no flags>
Extended supported rates: 24.0 36.0 48.0 54.0
HT capabilities:
Capabilities: 0x1ad
RX LDPC
HT20
SM Power Save disabled
RX HT20 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 3839 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT RX MCS rate indexes supported: 0-15
HT TX MCS rate indexes are undefined
AP Channel Report:
* operating class: 173
* channel(s): 1 27 255 255 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
HT operation:
* primary channel: 6
* secondary channel offset: no secondary
* STA channel width: 20 MHz
* RIFS: 1
* HT protection: no
* non-GF present: 1
* OBSS non-GF present: 0
* dual beacon: 0
* dual CTS protection: 0
* STBC beacon: 0
* L-SIG TXOP Prot: 0
* PCO active: 0
* PCO phase: 0
WMM: * Parameter version 1
* u-APSD
* BE: CW 15-1023, AIFSN 3
* BK: CW 15-1023, AIFSN 7
* VI: CW 7-15, AIFSN 2, TXOP 3008 usec
* VO: CW 3-7, AIFSN 2, TXOP 1504 usec
RSN: * Version: 1
* Group cipher: TKIP
* Pairwise ciphers: CCMP TKIP
* Authentication suites: PSK
* Capabilities: 16-PTKSA-RC 1-GTKSA-RC (0x000c)
WPA: * Version: 1
* Group cipher: TKIP
* Pairwise ciphers: CCMP TKIP
* Authentication suites: PSK
WPS: * Version: 1.0
* Wi-Fi Protected Setup State: 2 (Configured)
* Response Type: 3 (AP)
* UUID: 3b383f4b-4a3a-fb4b-fc3f-4a4e3b383f4b
* Manufacturer: Sagemcom
* Model: SagemcomFast3965_LB2.8
* Model Number: SG_LB3_1.2.3
* Serial Number: AN17040FF
* Primary Device Type: 6-0050f204-1
* Device name:
* Config methods: Ethernet, Label
* RF Bands: 0x1
* Version2: 2.0
BSS 44:d4:53:95:5c:f8(on wlx00e04c16cfec)
TSF: 1678100173188 usec (19d, 10:08:20)
freq: 2462
beacon interval: 100 TUs
capability: ESS Privacy SpectrumMgmt ShortSlotTime RadioMeasure (0x1511)
signal: -96.00 dBm
last seen: 160 ms ago
SSID: Livebox-7C40
Supported rates: 1.0* 2.0* 5.5* 11.0* 18.0 24.0 36.0 54.0
DS Parameter set: channel 11
TIM: DTIM Count 0 DTIM Period 3 Bitmap Control 0x0 Bitmap[0] 0x0
Country: FR Environment: Indoor/Outdoor
Channels [1 - 13] @ 20 dBm
Power constraint: 0 dB
TPC report: TX power: 13 dBm
ERP: Barker_Preamble_Mode
Extended supported rates: 6.0 9.0 12.0 48.0
RSN: * Version: 1
* Group cipher: CCMP
* Pairwise ciphers: CCMP
* Authentication suites: PSK
* Capabilities: 16-PTKSA-RC 1-GTKSA-RC (0x000c)
BSS Load:
* station count: 0
* channel utilisation: 30/255
* available admission capacity: 0 [*32us]
AP Channel Report:
* operating class: 129
* channel(s): 100 112
AP Channel Report:
* operating class: 81
* channel(s): 1
AP Channel Report:
* operating class: 0
* channel(s): 1
RM enabled capabilities:
Capabilities: 0x33 0x4f 0x00 0x00 0x00
Link Measurement
Neighbor Report
Beacon Passive Measurement
Beacon Active Measurement
Frame Measurement
Channel Load
Noise Histogram Measurement
Statistics Measurement
Transmit Stream/Category Measurement
Nonoperating Channel Max Measurement Duration: 0
Measurement Pilot Capability: 0
Supported operating classes:
* current operating class: 4
* operating class: 4
* operating class: 11
* operating class: 12
HT capabilities:
Capabilities: 0x19ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 4 usec (0x05)
HT RX MCS rate indexes supported: 0-23
HT TX MCS rate indexes are undefined
HT operation:
* primary channel: 11
* secondary channel offset: no secondary
* STA channel width: 20 MHz
* RIFS: 1
* HT protection: nonmember
* non-GF present: 0
* OBSS non-GF present: 1
* dual beacon: 0
* dual CTS protection: 0
* STBC beacon: 0
* L-SIG TXOP Prot: 0
* PCO active: 0
* PCO phase: 0
Overlapping BSS scan params:
* passive dwell: 20 TUs
* active dwell: 10 TUs
* channel width trigger scan interval: 300 s
* scan passive total per channel: 200 TUs
* scan active total per channel: 20 TUs
* BSS width channel transition delay factor: 5
* OBSS Scan Activity Threshold: 0.25 %
Extended capabilities:
* HT Information Exchange Supported
* Extended Channel Switching
* Event
* BSS Transition
* Operating Mode Notification
* Reserved Reserved Channel Schedule Management
* Reserved Channel Schedule Management
* 6
HE capabilities:
HE MAC Capabilities (0x000512181000):
+HTC HE Supported
TWT Responder
BSR
Broadcast TWT
OM Control
Maximum A-MPDU Length Exponent: 2
OM Control UL MU Data Disable RX
HE PHY Capabilities: (0x222002c00f429510008c00):
HE40/2.4GHz
242 tone RUs/2.4GHz
LDPC Coding in Payload
NDP with 4x HE-LTF and 3.2us GI
Rx HE MU PPDU from Non-AP STA
SU Beamformer
SU Beamformee
MU Beamformer
Beamformee STS <= 80Mhz: 3
Sounding Dimensions <= 80Mhz: 2
Ng = 16 SU Feedback
Codebook Size SU Feedback
Triggered SU Beamforming Feedback
Triggered CQI Feedback
PPE Threshold Present
Max NC: 2
TX 1024-QAM
RX 1024-QAM
HE RX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: MCS 0-11
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE TX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: MCS 0-11
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
PPE Threshold 0x1a 0x1c 0xc7 0x71 0x1c 0x07
WPS: * Version: 1.0
* Wi-Fi Protected Setup State: 2 (Configured)
* AP setup locked: 0x01
* RF Bands: 0x3
* Version2: 2.0
WMM: * Parameter version 1
* BE: CW 15-1023, AIFSN 3
* BK: CW 15-1023, AIFSN 7
* VI: CW 7-15, AIFSN 2, TXOP 3008 usec
* VO: CW 3-7, AIFSN 2, TXOP 1504 usec
############## iw dev ####################
phy#1
Interface wlp2s0b1
ifindex 5
wdev 0x100000001
addr 38:59:f9:8d:8a:86
ssid Livebox-2EBC
type managed
channel 11 (2462 MHz), width: 20 MHz, center1: 2462 MHz
txpower 19.00 dBm
multicast TXQ:
qsz-byt qsz-pkt flows drops marks overlmt hashcol tx-bytes tx-packets
0 0 0 0 0 0 0 0 0
phy#0
Interface wlx00e04c16cfec
ifindex 4
wdev 0x1
addr 00:e0:4c:16:cf:ec
ssid Livebox-2EBC
type managed
channel 11 (2462 MHz), width: 20 MHz, center1: 2462 MHz
txpower 20.00 dBm
multicast TXQ:
qsz-byt qsz-pkt flows drops marks overlmt hashcol tx-bytes tx-packets
0 0 0 0 0 0 0 0 0
######### iw dev wwx028037ec0200 link #############
Not connected.
######## iw dev wwx028037ec0200 station dump ###########
######## iw list ###########
Wiphy phy1
wiphy index: 1
max # scan SSIDs: 4
max scan IEs length: 2257 bytes
max # sched scan SSIDs: 0
max # match sets: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports RSN-IBSS.
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP-128 (00-0f-ac:4)
* CCMP-256 (00-0f-ac:10)
* GCMP-128 (00-0f-ac:8)
* GCMP-256 (00-0f-ac:9)
Available Antennas: TX 0 RX 0
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
Band 1:
Capabilities: 0x7c
HT20
SM Power Save disabled
RX Greenfield
RX HT20 SGI
RX HT40 SGI
No RX STBC
Max AMSDU length: 3839 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT Max RX data rate: 72 Mbps
HT TX/RX MCS rate indexes supported: 0-7
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps (short preamble supported)
* 5.5 Mbps (short preamble supported)
* 11.0 Mbps (short preamble supported)
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 2412 MHz [1] (19.0 dBm)
* 2417 MHz [2] (19.0 dBm)
* 2422 MHz [3] (19.0 dBm)
* 2427 MHz [4] (19.0 dBm)
* 2432 MHz [5] (19.0 dBm)
* 2437 MHz [6] (19.0 dBm)
* 2442 MHz [7] (19.0 dBm)
* 2447 MHz [8] (19.0 dBm)
* 2452 MHz [9] (19.0 dBm)
* 2457 MHz [10] (19.0 dBm)
* 2462 MHz [11] (19.0 dBm)
* 2467 MHz [12] (19.0 dBm)
* 2472 MHz [13] (19.0 dBm)
* 2484 MHz [14] (disabled)
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* new_station
* new_mpath
* set_mesh_config
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* join_mesh
* remain_on_channel
* set_tx_bitrate_mask
* frame
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* probe_client
* set_noack_map
* register_beacons
* start_p2p_device
* set_mcast_rate
* connect
* disconnect
* set_qos_map
* set_multicast_to_unicast
software interface modes (can always be added):
* AP/VLAN
* monitor
interface combinations are not supported
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
Device supports SAE with AUTHENTICATE command
Device supports low priority scan.
Device supports scan flush.
Device supports AP scan.
Device supports per-vif TX power setting
Driver supports full state transitions for AP/GO clients
Driver supports a userspace MPM
Device supports configuring vdev MAC-addr on create.
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0x40 0xb0 0xc0 0xd0
* managed: 0x40 0xb0 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* mesh point: 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-device: 0x40 0xd0
Supported extended features:
* [ RRM ]: RRM
* [ FILS_STA ]: STA FILS (Fast Initial Link Setup)
* [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
* [ SCAN_RANDOM_SN ]: use random sequence numbers in scans
* [ SCAN_MIN_PREQ_CONTENT ]: use probe request with only rate IEs in scans
* [ CAN_REPLACE_PTK0 ]: can safely replace PTK 0 when rekeying
* [ EXT_KEY_ID ]: Extended Key ID support
* [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
* [ DEL_IBSS_STA ]: deletion of IBSS station support
* [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
* [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support
Wiphy phy0
wiphy index: 0
max # scan SSIDs: 4
max scan IEs length: 2257 bytes
max # sched scan SSIDs: 0
max # match sets: 0
RTS threshold: 2347
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP-128 (00-0f-ac:4)
* CCMP-256 (00-0f-ac:10)
* GCMP-128 (00-0f-ac:8)
* GCMP-256 (00-0f-ac:9)
Available Antennas: TX 0x3 RX 0x3
Configured Antennas: TX 0x3 RX 0x3
Supported interface modes:
* managed
* monitor
Band 1:
Capabilities: 0x6c
HT20
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
No RX STBC
Max AMSDU length: 3839 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 16 usec (0x07)
HT TX/RX MCS rate indexes supported: 0-15, 32
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps
* 5.5 Mbps
* 11.0 Mbps
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 2412 MHz [1] (20.0 dBm)
* 2417 MHz [2] (20.0 dBm)
* 2422 MHz [3] (20.0 dBm)
* 2427 MHz [4] (20.0 dBm)
* 2432 MHz [5] (20.0 dBm)
* 2437 MHz [6] (20.0 dBm)
* 2442 MHz [7] (20.0 dBm)
* 2447 MHz [8] (20.0 dBm)
* 2452 MHz [9] (20.0 dBm)
* 2457 MHz [10] (20.0 dBm)
* 2462 MHz [11] (20.0 dBm)
* 2467 MHz [12] (20.0 dBm)
* 2472 MHz [13] (20.0 dBm)
* 2484 MHz [14] (disabled)
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* new_station
* new_mpath
* set_mesh_config
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* join_mesh
* remain_on_channel
* set_tx_bitrate_mask
* frame
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* probe_client
* set_noack_map
* register_beacons
* start_p2p_device
* set_mcast_rate
* connect
* disconnect
* set_qos_map
* set_multicast_to_unicast
software interface modes (can always be added):
* monitor
interface combinations are not supported
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
Device supports SAE with AUTHENTICATE command
Device supports low priority scan.
Device supports scan flush.
Device supports AP scan.
Device supports per-vif TX power setting
Driver supports full state transitions for AP/GO clients
Driver supports a userspace MPM
Device supports configuring vdev MAC-addr on create.
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0x40 0xb0 0xc0 0xd0
* managed: 0x40 0xb0 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* mesh point: 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-device: 0x40 0xd0
Supported extended features:
* [ RRM ]: RRM
* [ FILS_STA ]: STA FILS (Fast Initial Link Setup)
* [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
* [ SCAN_RANDOM_SN ]: use random sequence numbers in scans
* [ SCAN_MIN_PREQ_CONTENT ]: use probe request with only rate IEs in scans
* [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
* [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
* [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support
############ iw dev wwx028037ec0200 scan ############
command failed: No such device (-19)
####### modinfo <wifi_modules> |grep parm #######
Modules parm for b43 :
parm: bad_frames_preempt:enable(1) / disable(0) Bad Frames Preemption (int)
parm: fwpostfix:Postfix for the .fw files to load. (string)
parm: hwpctl:Enable hardware-side power control (default off) (int)
parm: nohwcrypt:Disable hardware encryption. (int)
parm: hwtkip:Enable hardware tkip. (int)
parm: qos:Enable QOS support (default on) (int)
parm: btcoex:Enable Bluetooth coexistence (default on) (int)
parm: verbose:Log message verbosity: 0=error, 1=warn, 2=info(default), 3=debug (int)
parm: pio:Use PIO accesses by default: 0=DMA, 1=PIO (int)
parm: allhwsupport:Enable support for all hardware (even it if overlaps with the brcmsmac driver) (int)
Modules parm for brcmsmac :
Modules parm for cfg80211 :
parm: bss_entries_limit:limit to number of scan BSS entries (per wiphy, default 1000) (int)
parm: ieee80211_regdom:IEEE 802.11 regulatory domain code (charp)
parm: cfg80211_disable_40mhz_24ghz:Disable 40MHz support in the 2.4GHz band (bool)
Modules parm for mac80211 :
parm: minstrel_vht_only:Use only VHT rates when VHT is supported by sta. (bool)
parm: max_nullfunc_tries:Maximum nullfunc tx tries before disconnecting (reason 4). (int)
parm: max_probe_tries:Maximum probe tries before disconnecting (reason 4). (int)
parm: beacon_loss_count:Number of beacon intervals before we decide beacon was lost. (int)
parm: probe_wait_ms:Maximum time(ms) to wait for probe response before disconnecting (reason 4). (int)
parm: ieee80211_default_rc_algo:Default rate control algorithm for mac80211 to use (charp)
Modules parm for rtl8xxxu :
parm: debug:Set debug mask (int)
parm: ht40_2g:Enable HT40 support on the 2.4GHz band (bool)
parm: dma_aggregation:Enable DMA packet aggregation (bool)
parm: dma_agg_timeout:Set DMA aggregation timeout (range 1-127) (int)
parm: dma_agg_pages:Set DMA aggregation pages (range 1-127, 0 to disable) (int)
####### systemctl list network units #########
networkd-dispatcher.service loaded active running Dispatcher daemon for systemd-networkd
NetworkManager-wait-online.service loaded active exited Network Manager Wait Online
NetworkManager.service loaded active running Network Manager
systemd-networkd.service loaded inactive dead Network Configuration
systemd-resolved.service loaded active running Network Name Resolution
systemd-timesyncd.service loaded active running Network Time Synchronization
wpa_supplicant.service loaded active running WPA supplicant
######## nmcli connection show ###########
NAME UUID TYPE DEVICE
Livebox-2EBC 1 316d3f61-b412-48c0-bc62-3d9374afd996 wifi wlx00e04c16cfec
Livebox-2EBC 9ddc8657-8858-4c39-b923-b21529cb71b1 wifi wlp2s0b1
Connexion filaire 1 4cc3147e-edd0-3d4e-88fb-d2847f78042d ethernet --
Réseau Redmi A1 e5eada8c-788d-4da6-af1d-773b522ca4a0 bluetooth --
#### iptables -vL -t filter|nat|mangle|raw|security #####
\n ### table filter ###
Chain INPUT (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain FORWARD (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain OUTPUT (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
\n ### table nat ###
Chain PREROUTING (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain INPUT (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain OUTPUT (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain POSTROUTING (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
\n ### table mangle ###
Chain PREROUTING (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain INPUT (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain FORWARD (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain OUTPUT (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain POSTROUTING (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
\n ### table raw ###
Chain PREROUTING (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain OUTPUT (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
\n ### table security ###
Chain INPUT (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain FORWARD (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain OUTPUT (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
[/code]Hors ligne
#23 Le 15/02/2024, à 21:58
- RIMBAUT
Re : pilote rtl8xxxu a remplacé le rtl8198eu RÉSOLU
symeon@symeon-Latitude-E5420:~$ iw list
modinfo rtl8xxxu |grep parm
Wiphy phy1
wiphy index: 1
max # scan SSIDs: 4
max scan IEs length: 2257 bytes
max # sched scan SSIDs: 0
max # match sets: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports RSN-IBSS.
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP-128 (00-0f-ac:4)
* CCMP-256 (00-0f-ac:10)
* GCMP-128 (00-0f-ac:8)
* GCMP-256 (00-0f-ac:9)
Available Antennas: TX 0 RX 0
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
Band 1:
Capabilities: 0x7c
HT20
SM Power Save disabled
RX Greenfield
RX HT20 SGI
RX HT40 SGI
No RX STBC
Max AMSDU length: 3839 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT Max RX data rate: 72 Mbps
HT TX/RX MCS rate indexes supported: 0-7
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps (short preamble supported)
* 5.5 Mbps (short preamble supported)
* 11.0 Mbps (short preamble supported)
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 2412 MHz [1] (19.0 dBm)
* 2417 MHz [2] (19.0 dBm)
* 2422 MHz [3] (19.0 dBm)
* 2427 MHz [4] (19.0 dBm)
* 2432 MHz [5] (19.0 dBm)
* 2437 MHz [6] (19.0 dBm)
* 2442 MHz [7] (19.0 dBm)
* 2447 MHz [8] (19.0 dBm)
* 2452 MHz [9] (19.0 dBm)
* 2457 MHz [10] (19.0 dBm)
* 2462 MHz [11] (19.0 dBm)
* 2467 MHz [12] (19.0 dBm)
* 2472 MHz [13] (19.0 dBm)
* 2484 MHz [14] (disabled)
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* new_station
* new_mpath
* set_mesh_config
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* join_mesh
* remain_on_channel
* set_tx_bitrate_mask
* frame
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* probe_client
* set_noack_map
* register_beacons
* start_p2p_device
* set_mcast_rate
* connect
* disconnect
* set_qos_map
* set_multicast_to_unicast
software interface modes (can always be added):
* AP/VLAN
* monitor
interface combinations are not supported
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
Device supports SAE with AUTHENTICATE command
Device supports low priority scan.
Device supports scan flush.
Device supports AP scan.
Device supports per-vif TX power setting
Driver supports full state transitions for AP/GO clients
Driver supports a userspace MPM
Device supports configuring vdev MAC-addr on create.
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0x40 0xb0 0xc0 0xd0
* managed: 0x40 0xb0 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* mesh point: 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-device: 0x40 0xd0
Supported extended features:
* [ RRM ]: RRM
* [ FILS_STA ]: STA FILS (Fast Initial Link Setup)
* [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
* [ SCAN_RANDOM_SN ]: use random sequence numbers in scans
* [ SCAN_MIN_PREQ_CONTENT ]: use probe request with only rate IEs in scans
* [ CAN_REPLACE_PTK0 ]: can safely replace PTK 0 when rekeying
* [ EXT_KEY_ID ]: Extended Key ID support
* [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
* [ DEL_IBSS_STA ]: deletion of IBSS station support
* [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
* [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support
Wiphy phy0
wiphy index: 0
max # scan SSIDs: 4
max scan IEs length: 2257 bytes
max # sched scan SSIDs: 0
max # match sets: 0
RTS threshold: 2347
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP-128 (00-0f-ac:4)
* CCMP-256 (00-0f-ac:10)
* GCMP-128 (00-0f-ac:8)
* GCMP-256 (00-0f-ac:9)
Available Antennas: TX 0x3 RX 0x3
Configured Antennas: TX 0x3 RX 0x3
Supported interface modes:
* managed
* monitor
Band 1:
Capabilities: 0x6c
HT20
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
No RX STBC
Max AMSDU length: 3839 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 16 usec (0x07)
HT TX/RX MCS rate indexes supported: 0-15, 32
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps
* 5.5 Mbps
* 11.0 Mbps
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 2412 MHz [1] (20.0 dBm)
* 2417 MHz [2] (20.0 dBm)
* 2422 MHz [3] (20.0 dBm)
* 2427 MHz [4] (20.0 dBm)
* 2432 MHz [5] (20.0 dBm)
* 2437 MHz [6] (20.0 dBm)
* 2442 MHz [7] (20.0 dBm)
* 2447 MHz [8] (20.0 dBm)
* 2452 MHz [9] (20.0 dBm)
* 2457 MHz [10] (20.0 dBm)
* 2462 MHz [11] (20.0 dBm)
* 2467 MHz [12] (20.0 dBm)
* 2472 MHz [13] (20.0 dBm)
* 2484 MHz [14] (disabled)
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* new_station
* new_mpath
* set_mesh_config
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* join_mesh
* remain_on_channel
* set_tx_bitrate_mask
* frame
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* probe_client
* set_noack_map
* register_beacons
* start_p2p_device
* set_mcast_rate
* connect
* disconnect
* set_qos_map
* set_multicast_to_unicast
software interface modes (can always be added):
* monitor
interface combinations are not supported
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
Device supports SAE with AUTHENTICATE command
Device supports low priority scan.
Device supports scan flush.
Device supports AP scan.
Device supports per-vif TX power setting
Driver supports full state transitions for AP/GO clients
Driver supports a userspace MPM
Device supports configuring vdev MAC-addr on create.
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0x40 0xb0 0xc0 0xd0
* managed: 0x40 0xb0 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* mesh point: 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-device: 0x40 0xd0
Supported extended features:
* [ RRM ]: RRM
* [ FILS_STA ]: STA FILS (Fast Initial Link Setup)
* [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
* [ SCAN_RANDOM_SN ]: use random sequence numbers in scans
* [ SCAN_MIN_PREQ_CONTENT ]: use probe request with only rate IEs in scans
* [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
* [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
* [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support
parm: debug:Set debug mask (int)
parm: ht40_2g:Enable HT40 support on the 2.4GHz band (bool)
parm: dma_aggregation:Enable DMA packet aggregation (bool)
parm: dma_agg_timeout:Set DMA aggregation timeout (range 1-127) (int)
parm: dma_agg_pages:Set DMA aggregation pages (range 1-127, 0 to disable) (int)
symeon@symeon-Latitude-E5420:~$ Hors ligne
#24 Le 15/02/2024, à 21:59
- RIMBAUT
Re : pilote rtl8xxxu a remplacé le rtl8198eu RÉSOLU
Voilà les résultats du potocole d'Olivier
Hors ligne
#25 Le 15/02/2024, à 22:19
- xubu1957
Re : pilote rtl8xxxu a remplacé le rtl8198eu RÉSOLU
Tente :
sudo apt install broadcom-sta-dkmsAvec redémarrage.
> [SOLVED] Broadcom BCM4313 802.11bgn Wireless Network Adapter not detected
Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Réso|u] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci. Membre de Linux-Azur
Hors ligne