bcm43xx et Ubuntu 7.10

Morphy_ · Le 25/10/2007, à 14:11

tiens

@Portable:~$ ls '/home/m/Bureau/drivers'
bcmwl664.sys bcmwl6.inf bcmwl6.sys
Portable:~$ ndiswrapper -l
bcmwl6 : driver installed
device (14E4:4312) present (alternate driver: bcm43xx)

POur info, voyant toujours orange.

EXtrait dmesg

[ 35.864000] bcm43xx: Cannot register IRQ0
[ 38.168000] apm: BIOS not found.
[ 38.900000] Failure registering capabilities with primary security module.
[ 39.080000] Trying to free already-free IRQ 0
[ 39.156000] bcm43xx: IRQ_READY timeout
[ 39.156000] Bluetooth: Core ver 2.11
[ 39.156000] NET: Registered protocol family 31
[ 39.156000] Bluetooth: HCI device and connection manager initialized
[ 39.156000] Bluetooth: HCI socket layer initialized
[ 39.172000] Bluetooth: L2CAP ver 2.8
[ 39.172000] Bluetooth: L2CAP socket layer initialized
[ 39.176000] Bluetooth: RFCOMM socket layer initialized
[ 39.176000] Bluetooth: RFCOMM TTY layer initialized
[ 39.176000] Bluetooth: RFCOMM ver 1.8
[ 62.488000] bcm43xx: IRQ_READY timeout
[ 85.788000] bcm43xx: IRQ_READY timeout
[ 102.484000] spurious 8259A interrupt: IRQ15.
[ 109.076000] bcm43xx: IRQ_READY timeout
[ 132.364000] bcm43xx: IRQ_READY timeout
[ 155.672000] bcm43xx: IRQ_READY timeout
[ 178.976000] bcm43xx: IRQ_READY timeout
[ 302.264000] bcm43xx: IRQ_READY timeout
[ 306.476000] eth0: link up.
[ 306.476000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 316.796000] eth0: no IPv6 routers present
[ 366.404000] UDF-fs: No VRS found
[ 366.448000] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 366.508000] ISO 9660 Extensions: RRIP_1991A
[ 425.548000] bcm43xx: IRQ_READY timeout
[ 548.836000] bcm43xx: IRQ_READY timeout
[ 572.128000] bcm43xx: IRQ_READY timeout
[ 595.416000] bcm43xx: IRQ_READY timeout
[ 688.188000] bcm43xx driver
[ 688.192000] PCI: No IRQ known for interrupt pin A of device 0000:03:00.0.
[ 688.192000] PCI: Setting latency timer of device 0000:03:00.0 to 64
[ 688.488000] bcm43xx: Cannot register IRQ0
[ 691.704000] Trying to free already-free IRQ 0
[ 691.780000] bcm43xx: IRQ_READY timeout

Dernière modification par Morphy_ (Le 25/10/2007, à 14:14)

belga · Le 25/10/2007, à 17:46

tape ceci

sudo modprobe -r bcm43xx
sudo modprobe ndiswrapper

que donne alors

iwlist scan
sudo lshw -C network

Morphy_ · Le 25/10/2007, à 17:54

déjà y'a un soucis :

@Portable:~$ sudo modprobe ndiswrapper
FATAL: Module ndiswrapper not found.

Alors que je l'ai installé via le synaptic

belga · Le 25/10/2007, à 18:15

que donne

modprobe -l | grep ndiswrapper

Morphy_ · Le 25/10/2007, à 18:19

Absolument rien, ça me fait un retour à la ligne

pmal9000 · Le 25/10/2007, à 18:34

En fait j'ai plusieurs clients qui utilise linux et équipé de cartes broadcam. ma conclusion est la suivante: elle s'installe toutes néanmoins certaines fonctionnes très bien d'autres sont récalcitrantes.

En effet certain modèles perdent leur connexion ou on un débit ridicule, il faut essayer et espérer. Sinon une solution alternative et qui fonctionne tres bien avec clé usb c'est la clé de Hercules compatible livebox et autre box pas besoin de pilote elle prends ceux de ubuntu, de plus elle fonctione sur quasi toutes les distributions.Essayé sur Debian, mandrake, redhat, fedora, et knoppix.

Si vous avez la possibilitée de mettre une carte PMCIA les dlink sont reconnue également et sont tres performantes.

belga · Le 25/10/2007, à 18:40

va faire ta promo ailleurs

belga · Le 25/10/2007, à 18:48

Je me demande ce que tu as bien pu faire?
on installe à partit des sources:

sudo ndiswrapper -e bcmwl6
sudo apt-get remove ndiswrapper*
sudo apt-get install build-essential linux-headers-$(uname -r)
mkdir ~/ndiswrapper
cd ~/ndiswrapper
wget http://kent.dl.sourceforge.net/sourceforge/ndiswrapper/ndiswrapper-1.48.tar.gz
tar xzvf ndiswrapper-1.48.tar.gz
cd ndiswrapper-1.47
sudo make uninstall
make
sudo make install

puis réinstalle le driver de 20doze
puis vérifie ndiswrapper -l
puis message 27

Morphy_ · Le 25/10/2007, à 19:04

Ok donc maintenant ça donne :

@Portable:~$ iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning

.

@Portable:~$ sudo lshw -C network
*-network UNCLAIMED
description: Network controller
product: BCM4312 802.11a/b/g
vendor: Broadcom Corporation
physical id: 0
bus info: pci@0000:03:00.0
version: 01
width: 32 bits
clock: 33MHz
capabilities: pm msi pciexpress cap_list
configuration: latency=0

mais voyant toujours orange.

Extrait dmesg

[ 71.272000] bcm43xx: IRQ_READY timeout
[ 94.588000] bcm43xx: IRQ_READY timeout
[ 118.000000] bcm43xx: IRQ_READY timeout
[ 141.312000] bcm43xx: IRQ_READY timeout
[ 164.612000] bcm43xx: IRQ_READY timeout
[ 187.908000] bcm43xx: IRQ_READY timeout
[ 222.284000] spurious 8259A interrupt: IRQ15.
[ 311.200000] bcm43xx: IRQ_READY timeout
[ 434.488000] bcm43xx: IRQ_READY timeout
[ 557.772000] bcm43xx: IRQ_READY timeout
[ 681.056000] bcm43xx: IRQ_READY timeout
[ 804.348000] bcm43xx: IRQ_READY timeout
[ 927.644000] bcm43xx: IRQ_READY timeout
[ 1050.928000] bcm43xx: IRQ_READY timeout
[ 1174.212000] bcm43xx: IRQ_READY timeout
[ 1297.496000] bcm43xx: IRQ_READY timeout
[ 1420.784000] bcm43xx: IRQ_READY timeout
[ 1436.212000] irq 7: nobody cared (try booting with the "irqpoll" option)
[ 1436.212000] [<c015b594>] __report_bad_irq+0x24/0x80
[ 1436.212000] [<c015b852>] note_interrupt+0x262/0x2a0
[ 1436.212000] [<f885b6c2>] usb_hcd_irq+0x22/0x60 [usbcore]
[ 1436.212000] [<c015aab0>] handle_IRQ_event+0x30/0x60
[ 1436.212000] [<c015c46b>] handle_level_irq+0xdb/0x110
[ 1436.212000] [<c0106b1b>] do_IRQ+0x3b/0x70
[ 1436.212000] [<c0118735>] smp_apic_timer_interrupt+0x55/0x80
[ 1436.212000] [<c0102e00>] default_idle+0x0/0x60
[ 1436.212000] [<c0105223>] common_interrupt+0x23/0x30
[ 1436.212000] [<c0102e00>] default_idle+0x0/0x60
[ 1436.212000] [<c011dba2>] native_safe_halt+0x2/0x10
[ 1436.212000] [<c0102e3c>] default_idle+0x3c/0x60
[ 1436.212000] [<c0102413>] cpu_idle+0x53/0xe0
[ 1436.212000] =======================
[ 1436.212000] handlers:
[ 1436.212000] [<f885b6a0>] (usb_hcd_irq+0x0/0x60 [usbcore])
[ 1436.212000] Disabling IRQ #7
[ 1544.076000] bcm43xx: IRQ_READY timeout
[ 1667.360000] bcm43xx: IRQ_READY timeout
[ 1790.644000] bcm43xx: IRQ_READY timeout
[ 1913.960000] bcm43xx: IRQ_READY timeout
[ 2037.260000] bcm43xx: IRQ_READY timeout
[ 2160.544000] bcm43xx: IRQ_READY timeout
[ 2183.848000] bcm43xx: IRQ_READY timeout
[ 2207.160000] bcm43xx: IRQ_READY timeout
[ 2230.552000] bcm43xx: IRQ_READY timeout
[ 2253.844000] bcm43xx: IRQ_READY timeout
[ 2277.136000] bcm43xx: IRQ_READY timeout
[ 2373.476000] ieee80211_crypt: unregistered algorithm 'NULL'
[ 2383.204000] ndiswrapper version 1.48 loaded (smp=yes, preempt=no)
[ 2383.228000] ndiswrapper (import:242): unknown symbol: NDIS.SYS:'NdisMRegisterInterruptEx'
[ 2383.228000] ndiswrapper (import:242): unknown symbol: NDIS.SYS:'NdisMIndicateStatusEx'
[ 2383.228000] ndiswrapper (import:242): unknown symbol: NDIS.SYS:'NdisFreeNetBufferList'
[ 2383.228000] ndiswrapper (import:242): unknown symbol: NDIS.SYS:'NdisAllocateMdl'
[ 2383.228000] ndiswrapper (import:242): unknown symbol: NDIS.SYS:'NdisFreeMdl'
[ 2383.228000] ndiswrapper (import:242): unknown symbol: NDIS.SYS:'NdisMRegisterMiniportDriver'
[ 2383.228000] ndiswrapper (import:242): unknown symbol: NDIS.SYS:'NdisAllocateIoWorkItem'
[ 2383.228000] ndiswrapper (import:242): unknown symbol: NDIS.SYS:'NdisQueueIoWorkItem'
[ 2383.228000] ndiswrapper (import:242): unknown symbol: NDIS.SYS:'NdisMSetMiniportAttributes'
[ 2383.228000] ndiswrapper (import:242): unknown symbol: NDIS.SYS:'NdisMDeregisterInterruptEx'
[ 2383.228000] ndiswrapper (import:242): unknown symbol: NDIS.SYS:'NdisMGetBusData'
[ 2383.228000] ndiswrapper (import:242): unknown symbol: NDIS.SYS:'NdisMRegisterScatterGatherDma'
[ 2383.228000] ndiswrapper (import:242): unknown symbol: NDIS.SYS:'NdisAllocateNetBufferListPool'
[ 2383.228000] ndiswrapper (import:242): unknown symbol: NDIS.SYS:'NdisMOidRequestComplete'
[ 2383.228000] ndiswrapper (import:242): unknown symbol: NDIS.SYS:'NdisFreeNetBufferListPool'
[ 2383.228000] ndiswrapper (import:242): unknown symbol: NDIS.SYS:'NdisMDeregisterScatterGatherDma'
[ 2383.228000] ndiswrapper (import:242): unknown symbol: NDIS.SYS:'NdisMSetBusData'
[ 2383.228000] ndiswrapper (import:242): unknown symbol: NDIS.SYS:'NdisAllocateNetBufferAndNetBufferList'
[ 2383.228000] ndiswrapper (import:242): unknown symbol: NDIS.SYS:'NdisMSendNetBufferListsComplete'
[ 2383.228000] ndiswrapper (import:242): unknown symbol: NDIS.SYS:'NdisMDeregisterMiniportDriver'
[ 2383.228000] ndiswrapper (import:242): unknown symbol: NDIS.SYS:'NdisOpenConfigurationEx'
[ 2383.228000] ndiswrapper (import:242): unknown symbol: NDIS.SYS:'NdisFreeIoWorkItem'
[ 2383.228000] ndiswrapper (import:242): unknown symbol: NDIS.SYS:'NdisMSynchronizeWithInterruptEx'
[ 2383.228000] ndiswrapper (import:242): unknown symbol: NDIS.SYS:'NdisMIndicateReceiveNetBufferLists'
[ 2383.228000] ndiswrapper (import:242): unknown symbol: NDIS.SYS:'NdisAllocateMemoryWithTagPriority'
[ 2383.228000] ndiswrapper (load_sys_files:216): couldn't prepare driver 'bcmwl6'
[ 2383.232000] ndiswrapper (load_wrap_driver:118): couldn't load driver bcmwl6; check system log for messages from 'loadndisdriver'
[ 2383.240000] usbcore: registered new interface driver ndiswrapper

Dernière modification par Morphy_ (Le 25/10/2007, à 19:06)

belga · Le 25/10/2007, à 19:12

Il faut trouver le bon driver
tape

sudo modprobe -r ndiswrapper
sudo ndiswrapper -e bcmwl6
echo 'blacklist bcm43xx' | sudo tee -a /etc/modprobe.d/blacklist
echo 'ndiswrapper' | sudo tee -a /etc/modules
cd
sudo aptitude install cabextract
wget http://ubunteros.free.fr/sp34152.exe
sudo mkdir bcmwl5
cabextract sp34152.exe bcmwl5
sudo ndiswrapper -i bcmwl5/bcmwl5.inf
sudo ndiswrapper -l
sudo ndiswrapper -m
sudo modprobe ndiswrapper

puis message 27
je dois partir

Dernière modification par belga (Le 25/10/2007, à 19:12)

Morphy_ · Le 26/10/2007, à 18:29

Bonsoit Belga

Désolé pour ma réponse tardive mais j'ai eu un soucis de DD

Bref, j'ai fait ce que tu m'avais dit et voici le retour des commandes :

@Portable:~$ sudo ndiswrapper -l
bcmwl5 : driver installed
device (14E4:4312) present (alternate driver: bcm43xx)
@Portable:~$ sudo ndiswrapper -m
adding "alias wlan0 ndiswrapper" to /etc/modprobe.d/ndiswrapper ...
@Portable:~$ sudo modprobe ndiswrapper
@Portable:~$ sudo modprobe -r bcm43xx
@Portable:~$ sudo modprobe ndiswrapper
@Portable:~$ iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
@Portable:~$ sudo lshw -C network
*-network UNCLAIMED
description: Network controller
product: BCM4312 802.11a/b/g
vendor: Broadcom Corporation
physical id: 0
bus info: pci@0000:03:00.0
version: 01
width: 32 bits
clock: 33MHz
capabilities: pm msi pciexpress cap_list
configuration: latency=0
@Portable:~$

Pas mieux apaprement

belga · Le 26/10/2007, à 18:49

le 4312 est méchante.
on installe le dernier ndiswrapper et un autre driver.

cd
sudo modprobe -r ndiswrapper
sudo ndiswrapper -e bcmwl5
sudo apt-get remove ndiswrapper-utils
sudo apt-get update
sudo apt-get install build-essential
sudo apt-get install linux-headers-`uname -r`
wget http://ftp.us.dell.com/network/R151517.EXE
wget http://internap.dl.sourceforge.net/sourceforge/ndiswrapper/ndiswrapper-1.48.tar.gz
tar -xzvf ndiswrapper-1.48.tar.gz
sudo make
sudo make install
mkdir DRIVER
unzip -a R151517.EXE -dDRIVER
sudo ndiswrapper -i DRIVER/DRIVER/bcmwl5.inf
sudo ndiswrapper -l
sudo ndiswrapper -m
sudo modprobe ndiswrapper

puis message 27

Morphy_ · Le 26/10/2007, à 19:35

Apparement ça n'a pas bougé d'un poils

@Portable:~$ sudo ndiswrapper -l
bcmwl5 : driver installed
device (14E4:4312) present (alternate driver: bcm43xx)
@Portable:~$ sudo ndiswrapper -m
module configuration already contains alias directive
@Portable:~$ sudo modprobe ndiswrapper
@Portable:~$ sudo modprobe -r bcm43xx
@Portable:~$ sudo modprobe ndiswrapper
@Portable:~$ iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
@Portable:~$ sudo lshw -C network
*-network UNCLAIMED
description: Network controller
product: BCM4312 802.11a/b/g
vendor: Broadcom Corporation
physical id: 0
bus info: pci@0000:03:00.0
version: 01
width: 32 bits
clock: 33MHz
capabilities: pm msi pciexpress cap_list
configuration: latency=0
@Portable:~$

willy78 · Le 26/10/2007, à 19:59

Tiens @Belga je crois que ceux-là sont pas mal!
http://rapidshare.com/files/65381338/bcmwl5.tar.gz.html

Morphy_ · Le 27/10/2007, à 12:00

Tu me fais signe quand tu repasses Belga

belga · Le 27/10/2007, à 12:06

pour l'instant je suis la

sudo modprobe -r ndiswrapper
sudo ndiswrapper -e bcmwl5

puis installe les drivers de willy78
puis

sudo modprobe ndiswrapper

que donne alors

iwlist scan
sudo lshw -C network

je vais manger

Dernière modification par belga (Le 27/10/2007, à 12:06)

Morphy_ · Le 27/10/2007, à 13:13

C'est hallucinant quand même, a croire qu'on tape dans le vide

@Portable:~$ sudo ndiswrapper -l
bcmwl5 : driver installed
device (14E4:4312) present (alternate driver: bcm43xx)
@Portable:~$ sudo ndiswrapper -m
module configuration already contains alias directive
@Portable:~$ sudo modprobe ndiswrapper
@Portable:~$ iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
@Portable:~$ sudo lshw -C network
*-network UNCLAIMED
description: Network controller
product: BCM4312 802.11a/b/g
vendor: Broadcom Corporation
physical id: 0
bus info: pci@0000:03:00.0
version: 01
width: 32 bits
clock: 33MHz
capabilities: pm msi pciexpress cap_list
configuration: latency=0

willy78 · Le 27/10/2007, à 13:36

C'est un complot du gouvernement, c'est les chinois du fbi qui te font une blague.
Sinon juste le temps que Belga finisse de manger essaye les même commandes avec une petite modif
on ne sais jamais!

sudo modprobe -r ndiswrapper
sudo rm -rf /etc/ndiswrapper/bcmwl5
sudo ndiswrapper -e bcmwl5

puis installe les drivers de willy78
puis

sudo modprobe ndiswrapper

que donne alors

iwlist scan
sudo lshw -C network

Dernière modification par willy78 (Le 27/10/2007, à 13:39)

Morphy_ · Le 27/10/2007, à 13:47

j'ai une erreur avec tes commandes

@Portable:~$ sudo modprobe -r ndiswrapper
@Portable:~$ sudo rm -rf /etc/ndiswrapper/bcmwl5
s@Portable:~$ sudo ndiswrapper -e bcmwl5
couldn't delete /etc/ndiswrapper/bcmwl5: Aucun fichier ou répertoire de ce type

belga · Le 27/10/2007, à 13:48

c'est normal, rien de grave

Au fait, il est récent ton portable?

Dernière modification par belga (Le 27/10/2007, à 13:49)

Morphy_ · Le 27/10/2007, à 13:51

bah on peut dire ça

Ordinateur portable HP Pavilion dv9053ea

willy78 · Le 27/10/2007, à 13:55

Morphy_ a écrit :

j'ai une erreur avec tes commandes
@Portable:~$ sudo modprobe -r ndiswrapper
@Portable:~$ sudo rm -rf /etc/ndiswrapper/bcmwl5
s@Portable:~$ sudo ndiswrapper -e bcmwl5
couldn't delete /etc/ndiswrapper/bcmwl5: Aucun fichier ou répertoire de ce type

Désolé j'ai inversé deux commandes mais c'est normal je me reveil seulement

Morphy_ · Le 27/10/2007, à 14:01

tiens si ça peut vous aider

@Portable:~$ dmesg
[ 0.000000] Linux version 2.6.22-14-generic (buildd@palmer) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Sun Oct 14 23:05:12 GMT 2007 (Ubuntu 2.6.22-14.46-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
[ 0.000000] BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007ff00000 (usable)
[ 0.000000] BIOS-e820: 000000007ff00000 - 000000007ff15000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007ff15000 - 000000007ff80000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007ff80000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] 1151MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000f8920
[ 0.000000] Entering add_active_range(0, 0, 524032) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 524032
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 524032
[ 0.000000] On node 0 totalpages: 524032
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 2302 pages used for memmap
[ 0.000000] HighMem zone: 292354 pages, LIFO batch:31
[ 0.000000] DMI present.
[ 0.000000] Nvidia board detected. Ignoring ACPI timer override.
[ 0.000000] If you got timer trouble try acpi_use_timer_override
[ 0.000000] Intel MultiProcessor Specification v1.4
[ 0.000000] Virtual Wire compatibility mode.
[ 0.000000] OEM ID: nVIDIA Product ID: C51-MCP51 APIC at: 0xFEE00000
[ 0.000000] Processor #0 15:8 APIC version 16
[ 0.000000] Processor #1 15:8 APIC version 16
[ 0.000000] I/O APIC #2 Version 17 at 0xFEC00000.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Processors: 2
[ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
[ 0.000000] Built 1 zonelists. Total pages: 519938
[ 0.000000] Kernel command line: root=UUID=e23abd1a-21ff-49f2-959c-caf8b4b0fcb0 ro quiet splash noapic nolapic acpi=off pnpbios=off locale=fr_FR
[ 0.000000] mapped APIC to ffffd000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffc000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 1607.390 MHz processor.
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 2066452k/2096128k available (2015k kernel code, 28456k reserved, 916k data, 364k init, 1178624k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfff4d000 - 0xfffff000 ( 712 kB)
[ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.000000] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 0.000000] .init : 0xc03e3000 - 0xc043e000 ( 364 kB)
[ 0.000000] .data : 0xc02f7d26 - 0xc03dce84 ( 916 kB)
[ 0.000000] .text : 0xc0100000 - 0xc02f7d26 (2015 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 0.000000] SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
[ 0.084000] Calibrating delay using timer specific routine.. 3217.69 BogoMIPS (lpj=6435397)
[ 0.084000] Security Framework v1.0.0 initialized
[ 0.084000] SELinux: Disabled at boot.
[ 0.084000] Mount-cache hash table entries: 512
[ 0.084000] CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000001f
[ 0.084000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.084000] CPU: L2 Cache: 512K (64 bytes/line)
[ 0.084000] CPU 0(2) -> Core 0
[ 0.084000] CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000001f
[ 0.084000] Compat vDSO mapped to ffffe000.
[ 0.084000] Checking 'hlt' instruction... OK.
[ 0.100000] SMP alternatives: switching to UP code
[ 0.100000] Early unpacking initramfs... done
[ 0.472000] CPU0: AMD Turion(tm) 64 X2 Mobile Technology TL-52 stepping 02
[ 0.472000] SMP alternatives: switching to SMP code
[ 0.472000] Booting processor 1/1 eip 3000
[ 0.480000] Initializing CPU#1
[ 0.560000] Calibrating delay using timer specific routine.. 3214.89 BogoMIPS (lpj=6429785)
[ 0.560000] CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000001f
[ 0.560000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.560000] CPU: L2 Cache: 512K (64 bytes/line)
[ 0.560000] CPU 1(2) -> Core 1
[ 0.560000] CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000001f
[ 0.560000] CPU1: AMD Turion(tm) 64 X2 Mobile Technology TL-52 stepping 02
[ 0.560000] Total of 2 processors activated (6432.59 BogoMIPS).
[ 0.668000] Brought up 2 CPUs
[ 0.740000] migration_cost=0
[ 0.740000] Booting paravirtualized kernel on bare hardware
[ 0.740000] Time: 13:55:34 Date: 09/27/107
[ 0.740000] NET: Registered protocol family 16
[ 0.744000] EISA bus registered
[ 0.756000] PCI: BIOS BUG #81[49435000] found
[ 0.756000] PCI: Using configuration type 1
[ 0.756000] Setting up standard PCI resources
[ 0.760000] ACPI: Interpreter disabled.
[ 0.760000] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.760000] pnp: PnP ACPI: disabled
[ 0.760000] PnPBIOS: Disabled
[ 0.760000] PCI: Probing PCI hardware
[ 0.760000] PCI: Probing PCI hardware (bus 00)
[ 0.760000] PCI: Transparent bridge - 0000:00:10.0
[ 0.760000] PCI: Discovered primary peer bus 04 [IRQ]
[ 0.760000] PCI: Using IRQ router default [10de/0260] at 0000:00:0a.0
[ 0.760000] NET: Registered protocol family 8
[ 0.760000] NET: Registered protocol family 20
[ 0.764000] PCI: Bridge: 0000:00:02.0
[ 0.764000] IO window: 4000-4fff
[ 0.764000] MEM window: c2000000-c3ffffff
[ 0.764000] PREFETCH window: c8200000-c83fffff
[ 0.764000] PCI: Bridge: 0000:00:03.0
[ 0.764000] IO window: disabled.
[ 0.764000] MEM window: c4000000-c5ffffff
[ 0.764000] PREFETCH window: disabled.
[ 0.764000] PCI: Failed to allocate mem resource #6:20000@e0000000 for 0000:05:00.0
[ 0.764000] PCI: Bridge: 0000:00:04.0
[ 0.764000] IO window: 5000-5fff
[ 0.764000] MEM window: c6000000-c7ffffff
[ 0.764000] PREFETCH window: d0000000-dfffffff
[ 0.764000] PCI: Bridge: 0000:00:10.0
[ 0.764000] IO window: disabled.
[ 0.764000] MEM window: c8000000-c80fffff
[ 0.764000] PREFETCH window: disabled.
[ 0.764000] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 0.764000] PCI: Setting latency timer of device 0000:00:03.0 to 64
[ 0.764000] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 0.764000] PCI: Setting latency timer of device 0000:00:10.0 to 64
[ 0.764000] NET: Registered protocol family 2
[ 0.800000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.800000] TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
[ 0.800000] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.800000] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.800000] TCP reno registered
[ 0.812000] checking if image is initramfs... it is
[ 1.540000] Freeing initrd memory: 7332k freed
[ 1.540000] audit: initializing netlink socket (disabled)
[ 1.540000] audit(1193493334.500:1): initialized
[ 1.540000] highmem bounce pool size: 64 pages
[ 1.544000] VFS: Disk quotas dquot_6.5.1
[ 1.544000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.544000] io scheduler noop registered
[ 1.544000] io scheduler anticipatory registered
[ 1.544000] io scheduler deadline registered
[ 1.544000] io scheduler cfq registered (default)
[ 1.740000] Clocksource tsc unstable (delta = 195972892 ns)
[ 9.564000] 0000:00:0b.1 EHCI: BIOS handoff failed (BIOS bug ?) 01010001
[ 9.564000] Boot video device is 0000:05:00.0
[ 9.564000] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 9.564000] assign_interrupt_mode Found MSI capability
[ 9.564000] Allocate Port Service[0000:00:02.0:pcie00]
[ 9.564000] PCI: Setting latency timer of device 0000:00:03.0 to 64
[ 9.564000] assign_interrupt_mode Found MSI capability
[ 9.564000] Allocate Port Service[0000:00:03.0:pcie00]
[ 9.564000] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 9.564000] assign_interrupt_mode Found MSI capability
[ 9.564000] Allocate Port Service[0000:00:04.0:pcie00]
[ 9.564000] isapnp: Scanning for PnP cards...
[ 9.916000] isapnp: No Plug & Play device found
[ 9.940000] Real Time Clock Driver v1.12ac
[ 9.940000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 9.940000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 9.944000] input: Macintosh mouse button emulation as /class/input/input0
[ 9.944000] PNP: No PS/2 controller found. Probing ports directly.
[ 9.960000] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 9.960000] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 9.960000] mice: PS/2 mouse device common for all mice
[ 9.960000] EISA: Probing bus 0 at eisa.0
[ 9.960000] Cannot allocate resource for EISA slot 3
[ 9.960000] Cannot allocate resource for EISA slot 4
[ 9.960000] Cannot allocate resource for EISA slot 5
[ 9.960000] EISA: Detected 0 cards.
[ 9.960000] TCP cubic registered
[ 9.960000] NET: Registered protocol family 1
[ 9.960000] Using IPI No-Shortcut mode
[ 9.960000] Magic number: 11:323:939
[ 9.960000] hash matches device ptyya
[ 9.960000] Freeing unused kernel memory: 364k freed
[ 9.980000] input: AT Translated Set 2 keyboard as /class/input/input1
[ 11.220000] AppArmor: AppArmor initialized<5>audit(1193493344.000:2): type=1505 info="AppArmor initialized" pid=1151
[ 11.228000] fuse init (API version 7.8)
[ 11.236000] Failure registering capabilities with primary security module.
[ 11.312000] thermal: Unknown symbol acpi_processor_set_thermal_limit
[ 11.860000] usbcore: registered new interface driver usbfs
[ 11.860000] usbcore: registered new interface driver hub
[ 11.860000] usbcore: registered new device driver usb
[ 11.860000] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 11.860000] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[ 11.860000] ohci_hcd 0000:00:0b.0: OHCI Host Controller
[ 11.860000] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1
[ 11.860000] ohci_hcd 0000:00:0b.0: irq 11, io mem 0xc0004000
[ 11.944000] usb usb1: configuration #1 chosen from 1 choice
[ 11.944000] hub 1-0:1.0: USB hub found
[ 11.944000] hub 1-0:1.0: 8 ports detected
[ 11.952000] SCSI subsystem initialized
[ 11.956000] libata version 2.21 loaded.
[ 11.964000] forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60.
[ 11.976000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 11.976000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 12.048000] PCI: Setting latency timer of device 0000:00:0b.1 to 64
[ 12.048000] ehci_hcd 0000:00:0b.1: EHCI Host Controller
[ 12.048000] ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2
[ 12.048000] ehci_hcd 0000:00:0b.1: debug port 1
[ 12.048000] PCI: cache line size of 64 is not supported by device 0000:00:0b.1
[ 12.048000] ehci_hcd 0000:00:0b.1: irq 7, io mem 0xc0005000
[ 12.048000] ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 12.048000] usb usb2: configuration #1 chosen from 1 choice
[ 12.048000] hub 2-0:1.0: USB hub found
[ 12.048000] hub 2-0:1.0: 8 ports detected
[ 12.152000] PCI: Setting latency timer of device 0000:00:14.0 to 64
[ 12.152000] forcedeth: using HIGHDMA
[ 12.576000] usb 2-4: new high speed USB device using ehci_hcd and address 2
[ 12.672000] eth0: forcedeth.c: subsystem: 0103c:30b7 bound to 0000:00:14.0
[ 12.672000] sata_nv 0000:00:0e.0: version 3.4
[ 12.672000] PCI: Enabling device 0000:00:0e.0 (0005 -> 0007)
[ 12.672000] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[ 12.672000] scsi0 : sata_nv
[ 12.672000] scsi1 : sata_nv
[ 12.672000] ata1: SATA max UDMA/133 cmd 0x000130c0 ctl 0x000130b6 bmdma 0x00013090 irq 5
[ 12.672000] ata2: SATA max UDMA/133 cmd 0x000130b8 ctl 0x000130b2 bmdma 0x00013098 irq 5
[ 12.716000] usb 2-4: configuration #1 chosen from 1 choice
[ 13.140000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 13.148000] ata1.00: ATA-7: ST9100824AS, 7.24, max UDMA/100
[ 13.148000] ata1.00: 195371568 sectors, multi 16: LBA48
[ 13.164000] ata1.00: configured for UDMA/100
[ 13.204000] usb 1-6: new low speed USB device using ohci_hcd and address 2
[ 13.416000] usb 1-6: configuration #1 chosen from 1 choice
[ 13.428000] usbcore: registered new interface driver hiddev
[ 13.436000] input: Microsoft Microsoft Notebook Optical Mouse with Tilt Wheel as /class/input/input2
[ 13.436000] input: USB HID v1.11 Mouse [Microsoft Microsoft Notebook Optical Mouse with Tilt Wheel] on usb-0000:00:0b.0-6
[ 13.436000] usbcore: registered new interface driver usbhid
[ 13.436000] /build/buildd/linux-source-2.6.22-2.6.22/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 13.476000] ata2: SATA link down (SStatus 0 SControl 300)
[ 13.480000] scsi 0:0:0:0: Direct-Access ATA ST9100824AS 7.24 PQ: 0 ANSI: 5
[ 13.480000] PCI: Enabling device 0000:00:0f.0 (0005 -> 0007)
[ 13.480000] PCI: Setting latency timer of device 0000:00:0f.0 to 64
[ 13.480000] scsi2 : sata_nv
[ 13.480000] scsi3 : sata_nv
[ 13.480000] ata3: SATA max UDMA/133 cmd 0x000130d8 ctl 0x000130ce bmdma 0x000130a0 irq 10
[ 13.480000] ata4: SATA max UDMA/133 cmd 0x000130d0 ctl 0x000130ca bmdma 0x000130a8 irq 10
[ 13.948000] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 13.956000] ata3.00: ATA-7: FUJITSU MHV2100BH PL, 892C, max UDMA/100
[ 13.956000] ata3.00: 195371568 sectors, multi 16: LBA48
[ 13.972000] ata3.00: configured for UDMA/100
[ 14.284000] ata4: SATA link down (SStatus 0 SControl 300)
[ 14.288000] scsi 2:0:0:0: Direct-Access ATA FUJITSU MHV2100B 892C PQ: 0 ANSI: 5
[ 14.344000] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[c8000000-c80007ff] Max Packet=[2048] IR/IT contexts=[4/4]
[ 14.348000] NFORCE-MCP51: IDE controller at PCI slot 0000:00:0d.0
[ 14.348000] NFORCE-MCP51: chipset revision 241
[ 14.348000] NFORCE-MCP51: not 100% native mode: will probe irqs later
[ 14.348000] NFORCE-MCP51: BIOS didn't set cable bits correctly. Enabling workaround.
[ 14.348000] NFORCE-MCP51: 0000:00:0d.0 (rev f1) UDMA133 controller
[ 14.348000] ide0: BM-DMA at 0x3080-0x3087, BIOS settings: hda:DMA, hdb:pio
[ 14.348000] Probing IDE interface ide0...
[ 14.364000] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 14.364000] sd 0:0:0:0: [sda] Write Protect is off
[ 14.364000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 14.364000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 14.364000] sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 14.364000] sd 0:0:0:0: [sda] Write Protect is off
[ 14.364000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 14.364000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 14.364000] sda: sda1
[ 14.368000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 14.368000] sd 2:0:0:0: [sdb] 195371568 512-byte hardware sectors (100030 MB)
[ 14.368000] sd 2:0:0:0: [sdb] Write Protect is off
[ 14.368000] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 14.368000] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 14.368000] sd 2:0:0:0: [sdb] 195371568 512-byte hardware sectors (100030 MB)
[ 14.368000] sd 2:0:0:0: [sdb] Write Protect is off
[ 14.368000] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 14.368000] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 14.368000] sdb: sdb1 sdb2 sdb3 sdb4
[ 14.488000] sd 2:0:0:0: [sdb] Attached SCSI disk
[ 14.492000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 14.492000] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 14.816000] Attempting manual resume
[ 14.816000] swsusp: Resume From Partition 8:20
[ 14.816000] PM: Checking swsusp image.
[ 14.816000] PM: Resume from disk failed.
[ 14.848000] kjournald starting. Commit interval 5 seconds
[ 14.848000] EXT3-fs: mounted filesystem with ordered data mode.
[ 15.084000] hda: MATSHITADVD-RAM UJ-850S, ATAPI CD/DVD-ROM drive
[ 15.420000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 21.776000] NET: Registered protocol family 10
[ 21.776000] lo: Disabled Privacy Extensions
[ 22.112000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 22.112000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 22.196000] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x3040
[ 22.196000] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x3000
[ 22.464000] sdhci: Secure Digital Host Controller Interface driver
[ 22.464000] sdhci: Copyright(c) Pierre Ossman
[ 22.464000] sdhci: SDHCI controller found at 0000:07:05.1 [1180:0822] (rev 19)
[ 22.464000] mmc0: SDHCI at 0xc8000800 irq 11 DMA
[ 22.552000] hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, (U)DMA
[ 22.552000] Uniform CD-ROM driver Revision: 3.20
[ 22.568000] Linux agpgart interface v0.102 (c) Dave Jones
[ 22.876000] nvidia: module license 'NVIDIA' taints kernel.
[ 23.128000] PCI: Setting latency timer of device 0000:05:00.0 to 64
[ 23.128000] NVRM: loading NVIDIA UNIX x86 Kernel Module 100.14.19 Wed Sep 12 14:12:24 PDT 2007
[ 23.132000] Linux video capture interface: v2.00
[ 23.260000] uvcvideo: Found UVC 1.00 device USB 2.0 Camera (0c45:62c0)
[ 23.260000] usbcore: registered new interface driver uvcvideo
[ 23.260000] USB Video Class driver (v0.1.0)
[ 23.368000] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x1a0b1, caps: 0xa04713/0x200000
[ 23.432000] input: SynPS/2 Synaptics TouchPad as /class/input/input3
[ 23.488000] PCI: Setting latency timer of device 0000:00:10.1 to 64
[ 24.524000] hda_intel: azx_get_response timeout, switching to polling mode...
[ 25.780000] lp: driver loaded but no devices found
[ 25.932000] ndiswrapper version 1.48 loaded (smp=yes, preempt=no)
[ 26.048000] ndiswrapper: driver bcmwl5 (Broadcom,10/12/2006, 4.100.15.5) loaded
[ 26.048000] PCI: No IRQ known for interrupt pin A of device 0000:03:00.0. Please try using pci=biosirq.
[ 26.048000] PCI: Setting latency timer of device 0000:03:00.0 to 64
[ 26.056000] ndiswrapper (IoConnectInterrupt:566): request for irq 0 failed
[ 26.056000] ndiswrapper: request for IRQ 0 failed
[ 26.056000] ndiswrapper (mp_init:216): couldn't initialize device: C000009A
[ 26.056000] ndiswrapper (pnp_start_device:439): Windows driver couldn't initialize the device (C0000001)
[ 26.056000] ndiswrapper (mp_halt:259): device f7f39500 is not initialized - not halting
[ 26.056000] ndiswrapper: device eth%d removed
[ 26.056000] ndiswrapper: probe of 0000:03:00.0 failed with error -22
[ 26.060000] usbcore: registered new interface driver ndiswrapper
[ 26.116000] Adding 819304k swap on /dev/sdb4. Priority:-1 extents:1 across:819304k
[ 26.656000] EXT3 FS on sdb2, internal journal
[ 27.504000] kjournald starting. Commit interval 5 seconds
[ 27.504000] EXT3 FS on sdb3, internal journal
[ 27.504000] EXT3-fs: mounted filesystem with ordered data mode.
[ 29.024000] powernow_k8: Unknown symbol acpi_processor_notify_smm
[ 29.024000] powernow_k8: Unknown symbol acpi_processor_unregister_performance
[ 29.024000] powernow_k8: Unknown symbol acpi_processor_register_performance
[ 29.060000] acpi_cpufreq: Unknown symbol acpi_processor_notify_smm
[ 29.060000] acpi_cpufreq: Unknown symbol acpi_processor_unregister_performance
[ 29.060000] acpi_cpufreq: Unknown symbol acpi_processor_preregister_performance
[ 29.060000] acpi_cpufreq: Unknown symbol acpi_processor_register_performance
[ 29.912000] ppdev: user-space parallel port driver
[ 29.996000] audit(1193486163.880:3): type=1503 operation="inode_permission" requested_mask="a" denied_mask="a" name="/dev/tty" pid=4674 profile="/usr/sbin/cupsd"
[ 30.048000] apm: BIOS not found.
[ 30.428000] Failure registering capabilities with primary security module.
[ 30.624000] Bluetooth: Core ver 2.11
[ 30.624000] NET: Registered protocol family 31
[ 30.624000] Bluetooth: HCI device and connection manager initialized
[ 30.624000] Bluetooth: HCI socket layer initialized
[ 30.632000] Bluetooth: L2CAP ver 2.8
[ 30.632000] Bluetooth: L2CAP socket layer initialized
[ 30.640000] Bluetooth: RFCOMM socket layer initialized
[ 30.640000] Bluetooth: RFCOMM TTY layer initialized
[ 30.640000] Bluetooth: RFCOMM ver 1.8
[ 32.720000] eth0: no IPv6 routers present
[ 34.680000] spurious 8259A interrupt: IRQ15.
[ 34.748000] ieee1394: Host added: ID:BUS[0-00:1023] GUID[009fc000a504c400]
[ 476.452000] irq 7: nobody cared (try booting with the "irqpoll" option)
[ 476.452000] [<c015b594>] __report_bad_irq+0x24/0x80
[ 476.452000] [<c015b852>] note_interrupt+0x262/0x2a0
[ 476.452000] [<f885b6c2>] usb_hcd_irq+0x22/0x60 [usbcore]
[ 476.452000] [<c015aab0>] handle_IRQ_event+0x30/0x60
[ 476.452000] [<c015c46b>] handle_level_irq+0xdb/0x110
[ 476.452000] [<c0106b1b>] do_IRQ+0x3b/0x70
[ 476.452000] [<c0118735>] smp_apic_timer_interrupt+0x55/0x80
[ 476.452000] [<c0102e00>] default_idle+0x0/0x60
[ 476.452000] [<c0105223>] common_interrupt+0x23/0x30
[ 476.452000] [<c0102e00>] default_idle+0x0/0x60
[ 476.452000] [<c011dba2>] native_safe_halt+0x2/0x10
[ 476.452000] [<c0102e3c>] default_idle+0x3c/0x60
[ 476.452000] [<c0102413>] cpu_idle+0x53/0xe0
[ 476.452000] =======================
[ 476.452000] handlers:
[ 476.452000] [<f885b6a0>] (usb_hcd_irq+0x0/0x60 [usbcore])
[ 476.452000] Disabling IRQ #7
[ 539.180000] usbcore: deregistering interface driver ndiswrapper
[ 539.184000] ndiswrapper (ntoskernel_exit:2714): object f7f01720(2) was not freed, freeing it now
[ 893.888000] ndiswrapper version 1.48 loaded (smp=yes, preempt=no)
[ 893.908000] ndiswrapper: driver bcmwl5 (Broadcom,10/12/2006, 4.100.15.5) loaded
[ 893.908000] PCI: No IRQ known for interrupt pin A of device 0000:03:00.0. Please try using pci=biosirq.
[ 893.908000] PCI: Setting latency timer of device 0000:03:00.0 to 64
[ 893.912000] ndiswrapper (IoConnectInterrupt:566): request for irq 0 failed
[ 893.916000] ndiswrapper: request for IRQ 0 failed
[ 893.916000] ndiswrapper (mp_init:216): couldn't initialize device: C000009A
[ 893.916000] ndiswrapper (pnp_start_device:439): Windows driver couldn't initialize the device (C0000001)
[ 893.916000] ndiswrapper (mp_halt:259): device f7012500 is not initialized - not halting
[ 893.916000] ndiswrapper: device eth%d removed
[ 893.916000] ndiswrapper: probe of 0000:03:00.0 failed with error -22
[ 893.920000] usbcore: registered new interface driver ndiswrapper
[ 1141.416000] uvcvideo: Failed to resubmit video URB (-45).
[ 1141.416000] uvcvideo: Failed to resubmit video URB (-45).
[ 1141.416000] uvcvideo: Failed to resubmit video URB (-45).
[ 1141.416000] uvcvideo: Failed to resubmit video URB (-45).
[ 3026.204000] usbcore: deregistering interface driver ndiswrapper
[ 3026.208000] ndiswrapper (ntoskernel_exit:2714): object f65f5320(2) was not freed, freeing it now
[ 3251.552000] ndiswrapper version 1.48 loaded (smp=yes, preempt=no)
[ 3251.620000] ndiswrapper: driver bcmwl5 (Broadcom,10/12/2006, 4.100.15.5) loaded
[ 3251.620000] PCI: No IRQ known for interrupt pin A of device 0000:03:00.0. Please try using pci=biosirq.
[ 3251.620000] PCI: Setting latency timer of device 0000:03:00.0 to 64
[ 3251.628000] ndiswrapper (IoConnectInterrupt:566): request for irq 0 failed
[ 3251.628000] ndiswrapper: request for IRQ 0 failed
[ 3251.628000] ndiswrapper (mp_init:216): couldn't initialize device: C000009A
[ 3251.628000] ndiswrapper (pnp_start_device:439): Windows driver couldn't initialize the device (C0000001)
[ 3251.628000] ndiswrapper (mp_halt:259): device f7012500 is not initialized - not halting
[ 3251.628000] ndiswrapper: device eth%d removed
[ 3251.628000] ndiswrapper: probe of 0000:03:00.0 failed with error -22
[ 3251.644000] usbcore: registered new interface driver ndiswrapper

belga · Le 27/10/2007, à 14:06

Il me reste deux cartouches

on a tjrs pas trouvé le bon driver (dmesg)

cd
sudo modprobe -r ndiswrapper
sudo ndiswrapper -e bcmwl5
wget ftp://ftp.hp.com/pub/softpaq/sp36501-37000/sp36684.exe
sudo rm -rf bcmwl5  #pas grave s'il y a un message d'erreur
sudo mkdir bcmwl5
cabextract sp36684.exe -dbcmwl5
sudo ndiswrapper -i bcmwl5/bcmwl5.inf
sudo ndiswrapper -l
sudo ndiswrapper -m
sudo modprobe ndiswrapper

puis poste

ndiswrapper -l
iwlist scan

Morphy_ · Le 27/10/2007, à 14:13

plus qu'une cartouche..

@Portable:~$ ndiswrapper -l
bcmwl5 : driver installed
device (14E4:4312) present (alternate driver: bcm43xx)
@Portable:~$ iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.

Ubuntu-fr

Navigation

Liens de recherche

Annonce

#26 Le 25/10/2007, à 14:11

Re : bcm43xx et Ubuntu 7.10

#27 Le 25/10/2007, à 17:46

Re : bcm43xx et Ubuntu 7.10

#28 Le 25/10/2007, à 17:54

Re : bcm43xx et Ubuntu 7.10

#29 Le 25/10/2007, à 18:15

Re : bcm43xx et Ubuntu 7.10

#30 Le 25/10/2007, à 18:19

Re : bcm43xx et Ubuntu 7.10

#31 Le 25/10/2007, à 18:34

Re : bcm43xx et Ubuntu 7.10

#32 Le 25/10/2007, à 18:40

Re : bcm43xx et Ubuntu 7.10

#33 Le 25/10/2007, à 18:48

Re : bcm43xx et Ubuntu 7.10

#34 Le 25/10/2007, à 19:04

Re : bcm43xx et Ubuntu 7.10

#35 Le 25/10/2007, à 19:12

Re : bcm43xx et Ubuntu 7.10

#36 Le 26/10/2007, à 18:29

Re : bcm43xx et Ubuntu 7.10

#37 Le 26/10/2007, à 18:49

Re : bcm43xx et Ubuntu 7.10

#38 Le 26/10/2007, à 19:35

Re : bcm43xx et Ubuntu 7.10

#39 Le 26/10/2007, à 19:59

Re : bcm43xx et Ubuntu 7.10

#40 Le 27/10/2007, à 12:00

Re : bcm43xx et Ubuntu 7.10

#41 Le 27/10/2007, à 12:06

Re : bcm43xx et Ubuntu 7.10

#42 Le 27/10/2007, à 13:13

Re : bcm43xx et Ubuntu 7.10

#43 Le 27/10/2007, à 13:36

Re : bcm43xx et Ubuntu 7.10

#44 Le 27/10/2007, à 13:47

Re : bcm43xx et Ubuntu 7.10

#45 Le 27/10/2007, à 13:48

Re : bcm43xx et Ubuntu 7.10

#46 Le 27/10/2007, à 13:51

Re : bcm43xx et Ubuntu 7.10

#47 Le 27/10/2007, à 13:55

Re : bcm43xx et Ubuntu 7.10

#48 Le 27/10/2007, à 14:01

Re : bcm43xx et Ubuntu 7.10

#49 Le 27/10/2007, à 14:06

Re : bcm43xx et Ubuntu 7.10

#50 Le 27/10/2007, à 14:13

Re : bcm43xx et Ubuntu 7.10

Pied de page des forums