Wifi Hercule USB connecter mais impossible de surfer !!

safinaz · Le 10/01/2008, à 22:29

ndiswrapper -l

avant

JOHAAANNS · Le 10/01/2008, à 22:37

johaaanns@johaaanns-pc:~$ ndiswrapper -l
rt2500usb : driver installed
johaaanns@johaaanns-pc:~$

safinaz · Le 10/01/2008, à 22:41

JOHAAANNS a écrit :

Resultat :

johaaanns@johaaanns-pc:~$ ls ~/Bureau
nouveau fichier~  rt2500usb.CAT  rt2500usb.INF  rt2500usb.SYS  rt2500usb.tar.gz
johaaanns@johaaanns-pc:~$

cd ~/Bureau
sudo modprobe -r ndiswrapper
sudo ndiswrapper -e HWGusb73
sudo ndiswrapper -i rt2500usb.INF
sudo modprobe ndiswrapper

puis poste

iwlist scan
ndiswrapper -l
sudo lshw -C network

JOHAAANNS · Le 10/01/2008, à 23:05

Merci de ta patience, j'ai l'impression d'etre un boulet !!!

johaaanns@johaaanns-pc:~/Bureau$ iwlist scan
lo        Interface doesn't support scanning.

eth0      Interface doesn't support scanning.

johaaanns@johaaanns-pc:~/Bureau$ ndiswrapper -l
rt2500usb : driver installed
johaaanns@johaaanns-pc:~/Bureau$ sudo lshw -C network
  *-network               
       description: Ethernet interface
       product: 3c940 10/100/1000Base-T [Marvell]
       vendor: 3Com Corporation
       physical id: 5
       bus info: pci@0000:02:05.0
       logical name: eth0
       version: 12
       serial: 00:0c:6e:9c:9b:64
       capacity: 1GB/s
       width: 32 bits
       clock: 66MHz
       capabilities: pm vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=skge driverversion=1.11 firmware=N/A latency=64 link=no maxlatency=31 mingnt=23 module=skge multicast=yes port=twisted pair
johaaanns@johaaanns-pc:~/Bureau$

safinaz · Le 10/01/2008, à 23:08

non vraiment pas tu as tout bien fait depuis le début
le problème c'est les différentes versions de ces drivers rt2500usb
qui court.

Donne le retour de

lsusb

safinaz · Le 10/01/2008, à 23:10

essaye aussi les drivers de serialmonkeys

sudo apt-get update
sudo apt-get install build-essential linux-headers-$(uname -r)
cd
mkdir rt2570
cd rt2570
wget http://rt2x00.serialmonkey.com/rt2570-cvs-daily.tar.gz
tar -zxvf rt2570-cvs-daily.tar.gz
cd rt2570-cvs*/Module
make
sudo make install
sudo modprobe rt2570

puis poste les retours de

sudo iwlist scanning
sudo lshw -C network

JOHAAANNS · Le 10/01/2008, à 23:24

Resultat :

sudo iwlist scanning
sudo lshw -C network

---------------------------

johaaanns@johaaanns-pc:~/Bureau$ lsusb
Bus 005 Device 010: ID 08ec:0834 M-Systems Flash Disk Pioneers 
Bus 005 Device 006: ID 06bd:2091 AGFA-Gevaert NV SnapScan e20
Bus 005 Device 004: ID 04b4:6560 Cypress Semiconductor Corp. CY7C65640 USB-2.0 "TetraHub"
Bus 005 Device 005: ID 04b4:6830 Cypress Semiconductor Corp. USB-2.0 IDE Adapter
Bus 005 Device 003: ID 06f8:e000 Guillemot Corp. 
Bus 005 Device 001: ID 0000:0000  
Bus 004 Device 001: ID 0000:0000  
Bus 002 Device 001: ID 0000:0000  
Bus 001 Device 004: ID 413c:3016 Dell Computer Corp. 
Bus 001 Device 001: ID 0000:0000  
Bus 003 Device 001: ID 0000:0000  
johaaanns@johaaanns-pc:~/Bureau$ 


-------------------------


johaaanns@johaaanns-pc:~/rt2570$ sudo iwlist scanning
lo        Interface doesn't support scanning.

eth0      Interface doesn't support scanning.

johaaanns@johaaanns-pc:~/rt2570$ sudo lshw -C network
  *-network               
       description: Ethernet interface
       product: 3c940 10/100/1000Base-T [Marvell]
       vendor: 3Com Corporation
       physical id: 5
       bus info: pci@0000:02:05.0
       logical name: eth0
       version: 12
       serial: 00:0c:6e:9c:9b:64
       capacity: 1GB/s
       width: 32 bits
       clock: 66MHz
       capabilities: pm vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=skge driverversion=1.11 firmware=N/A latency=64 link=no maxlatency=31 mingnt=23 module=skge multicast=yes port=twisted pair
johaaanns@johaaanns-pc:~/rt2570$

Alors j'ai fait aussi :

sudo apt-get update
sudo apt-get install build-essential linux-headers-$(uname -r)
cd
mkdir rt2570
cd rt2570
wget http://rt2x00.serialmonkey.com/rt2570-cvs-daily.tar.gz

Bien evidemment wget http://rt2x00.serialmonkey.com/rt2570-cvs-daily.tar.gz, ca ne fonctionne pas !!!

JOHAAANNS · Le 10/01/2008, à 23:25

On peux faire une pose aussi...:cool:
On peut reprendre demain !! la fatigue s'installe !!!
un grand merci en tout cas !!!

willy78 · Le 10/01/2008, à 23:29

pour les wget tu prends le lien et tu le telecharges (un peux d'initiative)

JOHAAANNS · Le 11/01/2008, à 00:02

Désolé..la fatigue...

Bon j'ai reussi a installer rt2570, il me redecte la clef USB Wifi, il trouve les ESSID mais tous à 0%, un moment en dhcp auto, et sans mettre de dns, je suis tombé sur un portail leneuf, (je suis chez free) (il m'a mis des dns auto), c'est que la connection doit fonctionner, j'ai donc mis mon essid, ma clef, mes dns, mon ip statique..et la rien!

Comme au tout debut, ca mouline dans le vent !!!

johaaanns@johaaanns-pc:~$ sudo iwlist scanning
[sudo] password for johaaanns:
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
rausb0 Scan completed :
Cell 01 - Address: 00:17:33:43:3E:48
Mode:Managed
ESSID:"Neuf WiFi"
Encryption key:off
Channel:11
Cell 02 - Address: 72:14:B6:99:8B:B0
Mode:Managed
ESSID:"tomtombolo"
Encryption key:on
Channel:1
Cell 03 - Address: 72:14:B6:99:8B:B3
Mode:Managed
ESSID:"freephonie"
Encryption key:on
Channel:1
Cell 04 - Address: 72:14:B6:99:8B:B1
Mode:Managed
ESSID:""
Encryption key:on
Channel:1
Cell 05 - Address: 72:14:B6:99:8B:B2
Mode:Managed
ESSID:""
Encryption key:on
Channel:1
Cell 06 - Address: CE:D9:14:E0:8C:D4
Mode:Managed
ESSID:"Wifi_JT_PM"
Encryption key:on
Channel:6
Cell 07 - Address: CE:D9:14:E0:8C:D7
Mode:Managed
ESSID:"freephonie"
Encryption key:on
Channel:6
Cell 08 - Address: CE:D9:14:E0:8C:D5
Mode:Managed
ESSID:""
Encryption key:on
Channel:6
Cell 09 - Address: CE:D9:14:E0:8C:D6
Mode:Managed
ESSID:""
Encryption key:on
Channel:6
Cell 10 - Address: 00:17:33:43:3E:41
Mode:Managed
ESSID:"NEUF_3E40"
Encryption key:on
Channel:11
Cell 11 - Address: 4E:5C:70:AC:03:D0
Mode:Managed
ESSID:""
Encryption key:on
Channel:11
Cell 12 - Address: 00:1B:2F:5F:03:54
Mode:Managed
ESSID:"Lemuria"
Encryption key:on
Channel:11
johaaanns@johaaanns-pc:~$ sudo lshw -C network
*-network
description: Ethernet interface
product: 3c940 10/100/1000Base-T [Marvell]
vendor: 3Com Corporation
physical id: 5
bus info: pci@0000:02:05.0
logical name: eth0
version: 12
serial: 00:0c:6e:9c:9b:64
capacity: 1GB/s
width: 32 bits
clock: 66MHz
capabilities: pm vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=skge driverversion=1.11 firmware=N/A latency=64 link=no maxlatency=31 mingnt=23 module=skge multicast=yes port=twisted pair
*-network
description: Wireless interface
physical id: 1
logical name: rausb0
serial: 00:08:d3:03:c0:45
capabilities: ethernet physical wireless
configuration: broadcast=yes multicast=yes wireless=RT2500USB WLAN
johaaanns@johaaanns-pc:~

Perso c'est Wifi_JT_PM

Vive les boulets !!

Dernière modification par JOHAAANNS (Le 11/01/2008, à 00:05)

safinaz · Le 11/01/2008, à 00:08

Il faut éditer le fichier pour donner les paramètres de connections

sudo gedit /etc/network/interfaces   #remplacer gedit par kwrite si tu es sous kubuntu

Placer ces lignes

en WEP hexa

auto wlan0
iface wlan0 inet dhcp
wireless-essid le_SSID_Du_rezo
wireless-key La_clé_en_hexa

en WPAPSK TKIP

auto wlan0
iface wlan0 inet dhcp
pre-up iwconfig wlan0 essid "mon ssid"
pre-up iwpriv wlan0 set AuthMode=WPAPSK
pre-up iwpriv wlan0 set EncrypType=TKIP
pre-up iwpriv wlan0 set WPAPSK="Ma_cle_WPA_Ultra_Secrete_que_y'a_que_moi_qui_sais"

rebooter et tester si la connexion est effective

safinaz · Le 11/01/2008, à 00:10

correction

safinaz a écrit :

Il faut éditer le fichier pour donner les paramètres de connections

sudo gedit /etc/network/interfaces   #remplacer gedit par kwrite si tu es sous kubuntu

ne laisser que

en WEP hexa

auto lo
iface lo inet loopback

auto wlan0
iface wlan0 inet dhcp
wireless-essid le_SSID_Du_rezo
wireless-key La_clé_en_hexa

en WPAPSK TKIP

auto lo
iface lo inet loopback

auto wlan0
iface wlan0 inet dhcp
pre-up iwconfig wlan0 essid "mon ssid"
pre-up iwpriv wlan0 set AuthMode=WPAPSK
pre-up iwpriv wlan0 set EncrypType=TKIP
pre-up iwpriv wlan0 set WPAPSK="Ma_cle_WPA_Ultra_Secrete_que_y'a_que_moi_qui_sais"

rebooter et tester si la connexion est effective

safinaz · Le 11/01/2008, à 01:19

tu peux faire ceci aussi (en parallèle)
télécharger
http://rapidshare.com/files/82839264/HWGusb.zip.html
tu vires les anciens drivers du bureau, extrait le zip et colle les 3 fichiers sur le bureau
puis

cd ~/Bureau
sudo modprobe -r ndiswrapper
sudo ndiswrapper -e rt2500usb
sudo ndiswrapper -i HWGusb.inf
sudo modprobe ndiswrapper

puis poste

iwlist scan
ndiswrapper -l
sudo lshw -C network

willy78 · Le 11/01/2008, à 07:30

Tiens c'est marrant le nom de l'interfaces est rausb0 comme avec les anciennes version du driver cvs

safinaz a écrit :

Il faut éditer le fichier pour donner les paramètres de connections

sudo gedit /etc/network/interfaces   #remplacer gedit par kwrite si tu es sous kubuntu

Placer ces lignes

en WEP hexa

auto rausb0
iface rausb0 inet dhcp
wireless-essid le_SSID_Du_rezo
wireless-key La_clé_en_hexa

en WPAPSK TKIP

auto rausb0
iface rausb0 inet dhcp
pre-up iwconfig rausb0 essid "mon ssid"
pre-up iwpriv rausb0 set AuthMode=WPAPSK
pre-up iwpriv rausb0 set EncrypType=TKIP
pre-up iwpriv rausb0 set WPAPSK="Ma_cle_WPA_Ultra_Secrete_que_y'a_que_moi_qui_sais"

rebooter et tester si la connexion est effective

JOHAAANNS · Le 11/01/2008, à 09:11

Bonjour,

En effet, c'est d'ailleurs ce que j'ai fait j'ai renommé wlan0 en rausb0 :

auto rausb0
iface rausb0 inet dhcp
pre-up iwconfig rausb0 essid "mon ssid"
pre-up iwpriv rausb0 set AuthMode=WPAPSK
pre-up iwpriv rausb0 set EncrypType=TKIP
pre-up iwpriv rausb0 set WPAPSK="Ma_cle_WPA_Ultra_Secrete_que_y'a_que_moi_qui_sais"

Ma ca ne marche pas du tout d'ailleurs ma clef ne s'allume meme pas !!

[je ne suis pas chez moi je regarderai ca ce soir, grand grand grand merci !!]

safinaz · Le 11/01/2008, à 11:34

safinaz a écrit :

tu peux faire ceci aussi (en parallèle)
télécharger
http://rapidshare.com/files/82839264/HWGusb.zip.html
tu vires les anciens drivers du bureau, extrait le zip et colle les 3 fichiers sur le bureau
puis
cd ~/Bureau
sudo modprobe -r ndiswrapper
sudo ndiswrapper -e rt2500usb
sudo ndiswrapper -i HWGusb.inf
sudo depmod -a
sudo ifconfig rausb0 down
sudo modprobe ndiswrapper
puis poste
iwlist scan
ndiswrapper -l
sudo lshw -C network

JOHAAANNS · Le 11/01/2008, à 19:05

C'est po gagné :::

johaaanns@johaaanns-pc:~/Bureau$ iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
rausb0 Interface doesn't support scanning.
johaaanns@johaaanns-pc:~/Bureau$ ndiswrapper -l
hwgusb : invalid driver!
johaaanns@johaaanns-pc:~/Bureau$ sudo lshw -C network
*-network
description: Ethernet interface
product: 3c940 10/100/1000Base-T [Marvell]
vendor: 3Com Corporation
physical id: 5
bus info: pci@0000:02:05.0
logical name: eth0
version: 12
serial: 00:0c:6e:9c:9b:64
capacity: 1GB/s
width: 32 bits
clock: 66MHz
capabilities: pm vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=skge driverversion=1.11 firmware=N/A latency=64 link=no maxlatency=31 mingnt=23 module=skge multicast=yes port=twisted pair
*-network DISABLED
description: Wireless interface
physical id: 1
logical name: rausb0
serial: 00:08:d3:03:c0:45
capabilities: ethernet physical wireless
configuration: broadcast=yes ip=192.168.0.1 multicast=yes wireless=RT2500USB WLAN
johaaanns@johaaanns-pc:~/Bureau$

j'ai un cd d'installation windows pour cette clef, ne serait il pas possible de faire qq choses avec les fichier contenu dans le cd...

oui bien evidemment ma clef est eteinte apres ces commandes !!

A savoir que la j'ecris d'un portable, qui n'a plus d'ecran, et dont le lecteur de dvd est dcd !!!

Dernière modification par JOHAAANNS (Le 11/01/2008, à 19:07)

safinaz · Le 11/01/2008, à 19:29

tu as raté l'installation
johaaanns@johaaanns-pc:~/Bureau$ ndiswrapper -l
hwgusb : invalid driver!

donne le retour de

ls ~/Bureau

et dis nous ce que contient le cd de driver

JOHAAANNS · Le 11/01/2008, à 20:00

johaaanns@johaaanns-pc:~/Bureau/HWGusb$ ls ~/Bureau
HWGusb.inf nouveau fichier~ rt25u98.sys save.txt~
HWGusb.zip rt2500usb.sys save.txt
johaaanns@johaaanns-pc:~/Bureau/HWGusb$ cd ~/Bureau
johaaanns@johaaanns-pc:~/Bureau$ sudo modprobe -r ndiswrapper
johaaanns@johaaanns-pc:~/Bureau$ sudo ndiswrapper -e rt2500usb
couldn't delete /etc/ndiswrapper/rt2500usb: Aucun fichier ou répertoire de ce type
johaaanns@johaaanns-pc:~/Bureau$ sudo ndiswrapper -i HWGusb.inf
driver hwgusb is already installed
johaaanns@johaaanns-pc:~/Bureau$ sudo depmod -a
johaaanns@johaaanns-pc:~/Bureau$ sudo ifconfig rausb0 down
johaaanns@johaaanns-pc:~/Bureau$ sudo modprobe ndiswrappe
FATAL: Module ndiswrappe not found.
johaaanns@johaaanns-pc:~/Bureau$ sudo modprobe ndiswrapper
johaaanns@johaaanns-pc:~/Bureau$
johaaanns@johaaanns-pc:~/Bureau$
johaaanns@johaaanns-pc:~/Bureau$ iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
rausb0 Interface doesn't support scanning.
johaaanns@johaaanns-pc:~/Bureau$ ndiswrapper -l
hwgusb : invalid driver!
johaaanns@johaaanns-pc:~/Bureau$ sudo lshw -C network
*-network
description: Ethernet interface
product: 3c940 10/100/1000Base-T [Marvell]
vendor: 3Com Corporation
physical id: 5
bus info: pci@0000:02:05.0
logical name: eth0
version: 12
serial: 00:0c:6e:9c:9b:64
capacity: 1GB/s
width: 32 bits
clock: 66MHz
capabilities: pm vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=skge driverversion=1.11 firmware=N/A latency=64 link=no maxlatency=31 mingnt=23 module=skge multicast=yes port=twisted pair
*-network DISABLED
description: Wireless interface
physical id: 1
logical name: rausb0
serial: 00:08:d3:03:c0:45
capabilities: ethernet physical wireless
configuration: broadcast=yes multicast=yes wireless=RT2500USB WLAN
johaaanns@johaaanns-pc:~/Bureau$

safinaz · Le 11/01/2008, à 20:03

hehe fais ceci,
il y a un changement

cd ~/Bureau
sudo modprobe -r ndiswrapper
sudo ndiswrapper -e hwgusb
sudo ndiswrapper -i HWGusb.inf
sudo depmod -a
sudo ifconfig rausb0 down
sudo modprobe ndiswrapper

puis poste

ndiswrapper -l
sudo lshw -C network

n'oublie de décrire ce que tu as dans le cd de driver

JOHAAANNS · Le 11/01/2008, à 20:15

johaaanns@johaaanns-pc:~$ cd ~/Bureau
johaaanns@johaaanns-pc:~/Bureau$ sudo modprobe -r ndiswrapper
johaaanns@johaaanns-pc:~/Bureau$ sudo ndiswrapper -e hwgusb
johaaanns@johaaanns-pc:~/Bureau$ sudo ndiswrapper -i HWGusb.inf
installing hwgusb ...
couldn't find SourceDisksFiles section - continuing anyway...
johaaanns@johaaanns-pc:~/Bureau$ sudo depmod -a
johaaanns@johaaanns-pc:~/Bureau$ sudo ifconfig rausb0 down
johaaanns@johaaanns-pc:~/Bureau$ sudo modprobe ndiswrapper
johaaanns@johaaanns-pc:~/Bureau$ ndiswrapper -l
hwgusb : driver installed
device (06F8:E000) present (alternate driver: rt2570)
johaaanns@johaaanns-pc:~/Bureau$ sudo lshw -C network
*-network
description: Ethernet interface
product: 3c940 10/100/1000Base-T [Marvell]
vendor: 3Com Corporation
physical id: 5
bus info: pci@0000:02:05.0
logical name: eth0
version: 12
serial: 00:0c:6e:9c:9b:64
capacity: 1GB/s
width: 32 bits
clock: 66MHz
capabilities: pm vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=skge driverversion=1.11 firmware=N/A latency=64 link=no maxlatency=31 mingnt=23 module=skge multicast=yes port=twisted pair
*-network DISABLED
description: Wireless interface
physical id: 1
logical name: rausb0
serial: 00:08:d3:03:c0:45
capabilities: ethernet physical wireless
configuration: broadcast=yes multicast=yes wireless=RT2500USB WLAN
johaaanns@johaaanns-pc:~/Bureau$

Voici le contenu

safinaz · Le 11/01/2008, à 20:19

cette fois ci c'est bon
hwgusb : driver installed
device (06F8:E000) present (alternate driver: rt2570)

tape

sudo ifconfig rausb0 down

sudo modprobe -r rt2570 #pas grave s'il y a un message d'erreur
sudo modprobe -r rt2500usb #pas grave s'il y a un message d'erreur
sudo modprobe -r ndiswrapper
sudo modprobe ndiswrapper

puis donne les retours de

sudo iwlist scanning
sudo lshw -C network
lsmod | grep usbcore
cat /etc/modules

safinaz · Le 11/01/2008, à 20:20

ok ce de la que je les ai pris.

JOHAAANNS · Le 11/01/2008, à 20:31

La y a du contenu !!
mais...

johaaanns@johaaanns-pc:~$ sudo ifconfig rausb0 down
[sudo] password for johaaanns:
Sorry, try again.
[sudo] password for johaaanns:
johaaanns@johaaanns-pc:~$ sudo modprobe -r rt2570
johaaanns@johaaanns-pc:~$ sudo modprobe -r rt2500usb
johaaanns@johaaanns-pc:~$ sudo modprobe -r ndiswrapper
johaaanns@johaaanns-pc:~$ sudo modprobe ndiswrapper
johaaanns@johaaanns-pc:~$ sudo iwlist scanning
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
wlan0 Scan completed :
Cell 01 - Address: 00:17:33:43:3E:48
ESSID:"Neuf WiFi"
Protocol:IEEE 802.11b
Mode:Managed
Frequency:2.462 GHz (Channel 11)
Quality:23/100 Signal level:-81 dBm Noise level:-96 dBm
Encryption key:off
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s
24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s
12 Mb/s; 48 Mb/s
Extra:bcn_int=100
Extra:atim=0
Cell 02 - Address: 72:14:B6:99:8B:B0
ESSID:"tomtombolo"
Protocol:IEEE 802.11b
Mode:Managed
Frequency:2.412 GHz (Channel 1)
Quality:35/100 Signal level:-73 dBm Noise level:-96 dBm
Encryption key:on
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
48 Mb/s; 54 Mb/s
Extra:bcn_int=100
Extra:atim=0
IE: WPA Version 1
Group Cipher : WEP-40
Pairwise Ciphers (2) : WEP-40 TKIP
Authentication Suites (1) : PSK
Cell 03 - Address: 72:14:B6:99:8B:B3
ESSID:"freephonie"
Protocol:IEEE 802.11b
Mode:Managed
Frequency:2.412 GHz (Channel 1)
Quality:35/100 Signal level:-73 dBm Noise level:-96 dBm
Encryption key:on
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
48 Mb/s; 54 Mb/s
Extra:bcn_int=100
Extra:atim=0
IE: WPA Version 1
Group Cipher : WEP-40
Pairwise Ciphers (1) : WEP-40
Authentication Suites (1) : 802.1x
Cell 04 - Address: 72:14:B6:99:8B:B1
ESSID:""
Protocol:IEEE 802.11b
Mode:Managed
Frequency:2.412 GHz (Channel 1)
Quality:34/100 Signal level:-74 dBm Noise level:-96 dBm
Encryption key:on
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
48 Mb/s; 54 Mb/s
Extra:bcn_int=100
Extra:atim=0
Cell 05 - Address: 72:14:B6:99:8B:B2
ESSID:""
Protocol:IEEE 802.11b
Mode:Managed
Frequency:2.412 GHz (Channel 1)
Quality:34/100 Signal level:-74 dBm Noise level:-96 dBm
Encryption key:on
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
48 Mb/s; 54 Mb/s
Extra:bcn_int=100
Extra:atim=0
Cell 06 - Address: CE:D9:14:E0:8C:D4
ESSID:"Wifi_JT_PM"
Protocol:IEEE 802.11b
Mode:Managed
Frequency:2.437 GHz (Channel 6)
Quality:67/100 Signal level:-53 dBm Noise level:-96 dBm
Encryption key:on
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
48 Mb/s; 54 Mb/s
Extra:bcn_int=100
Extra:atim=0
IE: WPA Version 1
Group Cipher : WEP-40
Pairwise Ciphers (1) : WEP-40
Authentication Suites (1) : PSK
Cell 07 - Address: CE:D9:14:E0:8C:D5
ESSID:""
Protocol:IEEE 802.11b
Mode:Managed
Frequency:2.437 GHz (Channel 6)
Quality:67/100 Signal level:-53 dBm Noise level:-96 dBm
Encryption key:on
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
48 Mb/s; 54 Mb/s
Extra:bcn_int=100
Extra:atim=0
Cell 08 - Address: CE:D9:14:E0:8C:D6
ESSID:""
Protocol:IEEE 802.11b
Mode:Managed
Frequency:2.437 GHz (Channel 6)
Quality:67/100 Signal level:-53 dBm Noise level:-96 dBm
Encryption key:on
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
48 Mb/s; 54 Mb/s
Extra:bcn_int=100
Extra:atim=0
Cell 09 - Address: CE:D9:14:E0:8C:D7
ESSID:"freephonie"
Protocol:IEEE 802.11b
Mode:Managed
Frequency:2.437 GHz (Channel 6)
Quality:67/100 Signal level:-53 dBm Noise level:-96 dBm
Encryption key:on
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
48 Mb/s; 54 Mb/s
Extra:bcn_int=100
Extra:atim=0
IE: WPA Version 1
Group Cipher : WEP-40
Pairwise Ciphers (1) : WEP-40
Authentication Suites (1) : 802.1x
Cell 10 - Address: 00:1B:2F:5F:03:54
ESSID:"Lemuria"
Protocol:IEEE 802.11b
Mode:Managed
Frequency:2.462 GHz (Channel 11)
Quality:31/100 Signal level:-76 dBm Noise level:-96 dBm
Encryption key:on
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
12 Mb/s; 24 Mb/s; 36 Mb/s; 9 Mb/s; 18 Mb/s
48 Mb/s; 54 Mb/s
Extra:bcn_int=100
Extra:atim=0
Cell 11 - Address: 00:17:33:43:3E:41
ESSID:"NEUF_3E40"
Protocol:IEEE 802.11b
Mode:Managed
Frequency:2.462 GHz (Channel 11)
Quality:21/100 Signal level:-82 dBm Noise level:-96 dBm
Encryption key:on
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s
24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s
12 Mb/s; 48 Mb/s
Extra:bcn_int=100
Extra:atim=0
IE: WPA Version 1
Group Cipher : WEP-40
Pairwise Ciphers (2) : TKIP WEP-40
Authentication Suites (1) : PSK
Cell 12 - Address: 00:14:A4:02:2F:2B
ESSID:"WANADOO-A22D"
Protocol:IEEE 802.11b
Mode:Managed
Frequency:2.462 GHz (Channel 11)
Quality:15/100 Signal level:-86 dBm Noise level:-96 dBm
Encryption key:off
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s
24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s
12 Mb/s; 48 Mb/s
Extra:bcn_int=100
Extra:atim=0
johaaanns@johaaanns-pc:~$ sudo lshw -C network
*-network
description: Ethernet interface
product: 3c940 10/100/1000Base-T [Marvell]
vendor: 3Com Corporation
physical id: 5
bus info: pci@0000:02:05.0
logical name: eth0
version: 12
serial: 00:0c:6e:9c:9b:64
capacity: 1GB/s
width: 32 bits
clock: 66MHz
capabilities: pm vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=skge driverversion=1.11 firmware=N/A latency=64 link=no maxlatency=31 mingnt=23 module=skge multicast=yes port=twisted pair
*-network
description: Wireless interface
physical id: 1
logical name: wlan0
serial: 00:08:d3:03:c0:45
capabilities: ethernet physical wireless
configuration: broadcast=yes driver=ndiswrapper+hwgusb driverversion=1.45+Hercules,07/15/2004, 1.02.0 link=yes multicast=yes wireless=IEEE 802.11g
johaaanns@johaaanns-pc:~$ lsmod | grep usbcore
usbcore 138632 7 ndiswrapper,usb_storage,libusual,usbhid,ehci_hcd,uhci_hcd
johaaanns@johaaanns-pc:~$ cat /etc/modules
# /etc/modules: kernel modules to load at boot time.
#
# This file contains the names of kernel modules that should be loaded
# at boot time, one per line. Lines beginning with "#" are ignored.
fuse
lp
sbp2
ndiswrapper
johaaanns@johaaanns-pc:~$

..je n'arrive pas a surfer, je suis connecté 14%, puis 21%...mais "trouve pas la page"

On y est presque !!!

safinaz · Le 11/01/2008, à 20:36

c'est lequel le tien (n° cell)???

tape déjà ceci

echo 'blacklist 2570' | sudo tee -a /etc/modprobe.d/blacklist
echo -e 'auto lo\niface lo inet loopback\n' | sudo tee /etc/network/interfaces

puis redémarre et reposte

iwlist scan

Ubuntu-fr

Navigation

Liens de recherche

Annonce

#26 Le 10/01/2008, à 22:29

Re : Wifi Hercule USB connecter mais impossible de surfer !!

#27 Le 10/01/2008, à 22:37

Re : Wifi Hercule USB connecter mais impossible de surfer !!

#28 Le 10/01/2008, à 22:41

Re : Wifi Hercule USB connecter mais impossible de surfer !!

#29 Le 10/01/2008, à 23:05

Re : Wifi Hercule USB connecter mais impossible de surfer !!

#30 Le 10/01/2008, à 23:08

Re : Wifi Hercule USB connecter mais impossible de surfer !!

#31 Le 10/01/2008, à 23:10

Re : Wifi Hercule USB connecter mais impossible de surfer !!

#32 Le 10/01/2008, à 23:24

Re : Wifi Hercule USB connecter mais impossible de surfer !!

#33 Le 10/01/2008, à 23:25

Re : Wifi Hercule USB connecter mais impossible de surfer !!

#34 Le 10/01/2008, à 23:29

Re : Wifi Hercule USB connecter mais impossible de surfer !!

#35 Le 11/01/2008, à 00:02

Re : Wifi Hercule USB connecter mais impossible de surfer !!

#36 Le 11/01/2008, à 00:08

Re : Wifi Hercule USB connecter mais impossible de surfer !!

#37 Le 11/01/2008, à 00:10

Re : Wifi Hercule USB connecter mais impossible de surfer !!

#38 Le 11/01/2008, à 01:19

Re : Wifi Hercule USB connecter mais impossible de surfer !!

#39 Le 11/01/2008, à 07:30

Re : Wifi Hercule USB connecter mais impossible de surfer !!

#40 Le 11/01/2008, à 09:11

Re : Wifi Hercule USB connecter mais impossible de surfer !!

#41 Le 11/01/2008, à 11:34

Re : Wifi Hercule USB connecter mais impossible de surfer !!

#42 Le 11/01/2008, à 19:05

Re : Wifi Hercule USB connecter mais impossible de surfer !!

#43 Le 11/01/2008, à 19:29

Re : Wifi Hercule USB connecter mais impossible de surfer !!

#44 Le 11/01/2008, à 20:00

Re : Wifi Hercule USB connecter mais impossible de surfer !!

#45 Le 11/01/2008, à 20:03

Re : Wifi Hercule USB connecter mais impossible de surfer !!

#46 Le 11/01/2008, à 20:15

Re : Wifi Hercule USB connecter mais impossible de surfer !!

#47 Le 11/01/2008, à 20:19

Re : Wifi Hercule USB connecter mais impossible de surfer !!

#48 Le 11/01/2008, à 20:20

Re : Wifi Hercule USB connecter mais impossible de surfer !!

#49 Le 11/01/2008, à 20:31

Re : Wifi Hercule USB connecter mais impossible de surfer !!

#50 Le 11/01/2008, à 20:36

Re : Wifi Hercule USB connecter mais impossible de surfer !!

Pied de page des forums