Installation sur Amilo Xa 2528-P5311

Changedman · Le 07/01/2008, à 02:52

Bonjour (ou plutot bonne nuit) à tous les ubunteros !

Hier fur un jour heureux puisqu'il fut le jour oà¹ l'on m'offra un PC, des amis se sont cotisés et m'ont payé ce portable, un cadeau de noà«l en retard mais qui pourrait leur en vouloir.
Malheureusement (et malgré le fait que j'en parle assez régulierement), personne n'a pensé à verifier la compatibilité avec Ubuntu et c'est le drame.

Insertion du CD d'install, boot, on lance, PAF ! BIOS BUG #81, je recherche et vois que c'est apparemment un problème de gestion de l'ACPI. Je relance avec l'option noacpi, message d'erreur me disant : hda: probing with STATUS(0x50) instead of ALTSTATUS(0xff)
Que faire ? Il y a ensuite d'autres messages d'erreurs mais mieux vaut regler ces problèmes les uns après les autres.
Je suis donc condamné à rester sous vista en attendant vos reponses, c'est dire ma detresse...:P(j'en fais peut-être un peu trop)
EDIT :
Ensuite viens :

hda: probing with STATUS(0x50) instead of ALTSTATUS(0xff)
hda: probing with STATUS(0x51) instead of ALTSTATUS(0xff)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda : irq timeout: status=0x58 {DriveReady SeekCompete DataRequest }
ide: failed opcode was: 0xa1
ide-cd:cmd 0x5a timed out
hda: irq timeout:status=0x51 { DriveReady SeekComplete Error }
hda: irq timeout: error=0x64 { AbortedCommand LastFailedSense=0x06 }
ACPI: PCI Interrupt [LNK1] enbaled at IRQ 11

(La derniere ligne n'est pas sure)
Les lignes que j'ai pu recuperer avant qu'il ne me sorte un "Triying to enable frame-buffer" qui ne donna rien

Dernière modification par Changedman (Le 07/01/2008, à 03:19)

abraxas-dalytics · Le 07/01/2008, à 13:41

Salut, j'ai le même portable et je galère aussi.

J'ai quand même pu installer la Ubuntu, mais pour le moment elle ne marche qu'en mode recovery en effectuant quelques bidouilles.

Comme il est impossible de faire tourner un live CD ou un live DVD avec ce **** de lecteur DVDRAM de chez LG ( la KNOPPIX ne marche pas non plus et ni la Solaris 10, ni FreeBSD ne peuvent s'installer, quel malheur!!!), il faut que tu fasses une Net install (installation par le réseau qui charge juste les drivers de la carte réseau). Il faut que tu sois connecté à Internet avec un cà¢ble Ethernet.

Tu peux télécharger l'image ici : http://fr.archive.ubuntu.com/ubuntu/dis … t/mini.iso

Bonne installation.

Si tu arrives à faire marcher le son ou le DVDRAM préviens-moi.

Conseil: pour le moment garde le Vista installé, car il faut qu'on règle un paquet de problèmes de compatibilité.

A @

Changedman · Le 07/01/2008, à 13:48

Merci beaucoup, je vais tenter l'install sur une petite partition dès maintenant.

NicoLarve · Le 09/01/2008, à 09:36

Salut à vous,

Nous avons résolu certains problèmes liés à ce portable: Wifi (avec ndiswrapper) et pilote Alsa (pas de son dans les HP: module recomilé avec les bonnes options), mais le pb du DVDRam devra certainement attendre le kernel 2.6.24.

[Résolu] Installation de Ubuntu: Pour Ubuntu 7.10, il semble que le module pilotant le bus IDE qui est chargé ne soit pas le bon (charge amd74xx.ko au lieu de pata_amd.ko et/ou ata_piix.ko), mais il y a de toutes manière un micmac qui me dépasse dans cette histoire...
Nous avons donc fait une installation à partir d'une clé USB bootable avec recopie du fichier squashfs du live CD Ubuntu sur cette clé!
Vous pouvez vous reporter à ce topic, en espérant que cela vous soit utile.

[Non-résolu] DVDRAM: J'ai aussi lu dans Linux Magazine de ce mois-ci (rubrique Kernel Corner, page 15) qu'un nouveau module de kernel nommé fujitsu_laptop sera intégré au kernel 2.6.24. Il devrait "prendre en charge certains paramètres spécifiques aux portables de chez Fujitsu" !
Il est aussi question d'une mauvaise détection des périphérique IDE, selon qu'ils soient reliés par des nappes à 40 fils ou à 80 fils. Hope !!!!

[Résolu] Son dans les HP: Pour faire en sorte que le son sorte sur les HP, il suffit de recompiler le pilote ALSA en lui spécifiant le bon modèle de carte son.
En lançant alsamixer depuis un terminal, vous aurez en haut à gauche, le nom complet de votre carte son (il très dur de s'y retrouver entre les différentes désignations "HDA-Intel", "MCP51 High Definition Audio", et autres...).

Ensuite, (et puisque malheureusement, je n'ai pas pris de notes le jour où j'ai réparé ce pb...) vous devrez aller lire la documentation de ALSA, ou du moins retrouver comment recompiler le pilote ALSA avec l'option concernant votre modèle de carte (il existe 2 variantes de cette carte, celle à 3 prises jack (la bonne) et l'autre à 6).
Notez que pour le moment, nous ne pouvons pas utiliser la molette analogique pour le réglage du volume (ce doit être encore une autre option qui manque !).

[Non-résolu] Télécommande: Notez aussi que la petite télécommande cachée dans un slot PCMCIA fonctionne en mode IRDA, et il parait que c'est très nul comme système car il n'a qu'une très courte portée (qques dizaines de centimètres), et je n'ai pas réussi à le faire fonctionner avec lirc. Un collègue de bon conseils m'a suggéré de laisser tomber.

Liste du matériel: Si vous voulez dégager Vista au plus vite, vous pourrez toujours récupérer la liste du matériel présent dans votre Amilo, sur cette page, vous pourrez aussi y récupérer le pilote Wifi pour Windows XP utilisable avec ndiswrapper pour Ubuntu ! (nécessite le fichier .inf et le fichier .sys du pilote Windows, attention, sur la page, y'à 2 pilotes Wifi différents).
Il existe aussi une page web (en plus des commandes lshw, lspci & lsusb) bien pratique pour identifier votre matos: http://kmuto.jp/debian/hcl/, rentrez simplement le résultat de la commande

lspci -n

Enfin, il est probable que le son se remette à fonctionner après l'installation d'Ubuntu et une mise à jour:

sudo apt-get update
sudo apt-get upgrade

Bonne chance !
N.

Dernière modification par NicoLarve (Le 09/01/2008, à 11:08)

Changedman · Le 09/01/2008, à 15:57

De nouveau merci, j'avais tenté d'installé en netinstall comme suggéré, l'install s'etait correctement déroulée (quoi que très longue avec des pauses parfais inquietantes) mais il me fut impossible de booter, echec...

Je vais donc tenter par USB et tenter de resoudre mes problèmes avec toutes ces indications, merci beaucoup pour cette aide

NicoLarve · Le 09/01/2008, à 16:31

Si tu ne peux pas booter, c'est peut-être que ton multi boot Grub est mal configuré...?
Si c'est la cas, ça se résout très vite en démarrant ton système avec Super Grub Disk (iso de 3Mo pour CD ou clé USB) qui saura trouver à ta place comment booter ton installation de Ubuntu ! ;-)

Ensuite, une fois Ubuntu démarré, tu peux éditer le fichier /boot/grub/menu.lst pour corriger tout ça.

Bonne chance, et courage !

Dernière modification par NicoLarve (Le 09/01/2008, à 18:24)

patco · Le 29/01/2008, à 06:30

[Non-résolu] DVDRAM: J'ai aussi lu dans Linux Magazine de ce mois-ci (rubrique Kernel Corner, page 15) qu'un nouveau module de kernel nommé fujitsu_laptop sera intégré au kernel 2.6.24. Il devrait "prendre en charge certains paramètres spécifiques aux portables de chez Fujitsu" !
Il est aussi question d'une mauvaise détection des périphérique IDE, selon qu'ils soient reliés par des nappes à 40 fils ou à 80 fils. Hope !!!!

salut, je viens d'installer gutsy 32 bit par le réseau et résolu le problème de cdrom:

http://doc.ubuntu-fr.org/materiel/liste_portables/fujitsu-siemens

CDROM pas repèré,
solution: installation par le réseau,
ensuite ajouter

sd_mod
ide-generic
ata_piix

dans /etc/initramfs-tools/modules
et refaire l'image initrd avec la commande
'update-initramfs -u /boot/k.initrd' (remplacer k.initrd par le nom de l'image)

Changedman · Le 29/01/2008, à 18:23

Je vais retenter l'installation alors !
Derniere question, pour la commande : 'update-initramfs -u /boot/k.initrd' (remplacer k.initrd par le nom de l'image)
Quel est sensé être le nom de l'image ?

Changedman · Le 29/01/2008, à 20:58

C'est fait, installé.
Je vais passer aux resolutions de problèmes mais il y en a un qui n'a pas été signalé, un demarrage d'au moins 5 minutes !
Ensuite, il tourne très vite mais 5 minutes de boot, c'est legerement long, une solution pour ceci aussi ?

Changedman · Le 29/01/2008, à 22:41

Bon et bien c'est encore une fois un echec de mon coté, le boot a été corrigé par la manipulation mais pas le lecteur DVD (qui est un optiarc chez moi (selon le BIOS)), il m'a été impossible de faire fonctionner le son, le wifi, etc

Vraiment degouté, je dois me lancer de nouveau dans une longue installation de Vista, que j'avais d'ailleurs réussi à fignoler pourqu'il soit un minimum potable et que je viens d'effacer pensant que mon PC fonctionnerait enfin sous Ubuntu. Je pense que nous n'avons pas tous exactement la même reference, il faudrait verifier....

patko · Le 30/01/2008, à 05:05

Changedman a écrit :

Je vais retenter l'installation alors !
Derniere question, pour la commande : 'update-initramfs -u /boot/k.initrd' (remplacer k.initrd par le nom de l'image)
Quel est sensé être le nom de l'image ?

j'étais un peu fatigué lors du post, désolé d'avoir été trop cryptique, l'image à refaire est celle que gutsy a installé dans le dossier /boot, c'est à dire:

initrd.img-2.6.22-14-generic

la manip' doit être refaite pour tout nouveau kernel à moins que le nouveau kernel fixe le problème, j'ai donc du refaire la manip' avec le noyau temps réel de ubuntustudio.

C'est fait, installé.
Je vais passer aux resolutions de problèmes mais il y en a un qui n'a pas été signalé, un demarrage d'au moins 5 minutes !
Ensuite, il tourne très vite mais 5 minutes de boot, c'est legerement long, une solution pour ceci aussi ?

il faut ajouter au fichier /boot/grub/menu.lst l'option noapic à la ligne 'kernel', ici ça redémarre en une minute, voici un extrait de mon menu.lst:

title Ubuntu 7.10, kernel 2.6.22-14-rt (recovery mode)
root (hd0,0)
kernel /vmlinuz-2.6.22-14-rt root=UUID=0ce9e0a4-4221-43de-b5c2-91d778be655d ro single noapic

Bon et bien c'est encore une fois un echec de mon coté, le boot a été corrigé par la manipulation mais pas le lecteur DVD (qui est un optiarc chez moi (selon le BIOS)), il m'a été impossible de faire fonctionner le son, le wifi, etc

on devrait avoir le même lecteur puisque c'est exactement le même modèle, et ça fonctionne aprés avoir ajoué les modules a l'initrd, voici un post avec lequel j'ai à demi solutionné le problème sur gutsy:

http://www.developpez.net/forums/archive/index.php/t-31828.html

Bug with ata_piix module prevent loading ide driver. You have to rebuild initrd image. Just add following to /etc/mkinitrd/modules:

mon dmesg est saturé par contre par ce message:

[ 2902.407159] ide: failed opcode was: unknown
[ 2902.407162] hda: drive not ready for command
[ 2937.369413] hda: irq timeout: status=0x51 { DriveReady SeekComplete Error }
[ 2937.369434] hda: irq timeout: error=0x64 { AbortedCommand LastFailedSense=0x0

je n'ai pas encore regardé pourquoi le son ne fonctionne pas, pour l'instant j'utilise une table firewire phonic qui fonctionne bien avec jack et freebob, aprés avoir upgradé vers ubuntustudio, et pour le wifi je verrais plus tard également, pour l'instant une connection filaire me suffit.

Vraiment degouté, je dois me lancer de nouveau dans une longue installation de Vista, que j'avais d'ailleurs réussi à fignoler pourqu'il soit un minimum potable et que je viens d'effacer pensant que mon PC fonctionnerait enfin sous Ubuntu. Je pense que nous n'avons pas tous exactement la même reference, il faudrait verifier....

Je suis assez satisfait de la puissance de la machine, car j'arrive à faire tourner sans problème windows trust dans une machine virtuelle, mais sans le son pour l'instant.

Impossible de trouver comment activer le KMV dans le bios, mais ça fonctionne quand même avec virtualbox (il faut faire un hack pour avoir l'USB)

L'acceleration graphique fonctionne trés correctement.

voilà , j'espère donner plus de nouvelles dans de brefs delais.

patko · Le 30/01/2008, à 19:52

En fait le module sd_mod permettait apparemet de faire apparaître le lecteur cdrom sur le bureau, je croayos qu'il fonctionnait, jusqu'à ce que je mette un cd dedans....:rolleyes:

hdparm -i /dev/hda > hdaparm.txt

Model=Optiarc DVD RW AD-7540A, FwRev=1.42, SerialNo=
Config={ Fixed Removeable DTR<=5Mbs DTR>10Mbs nonMagnetic }
RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0
BuffType=unknown, BuffSize=0kB, MaxMultSect=0
(maybe): CurCHS=0/0/0, CurSects=0, LBA=yes, LBAsects=0
IORDY=yes, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 *udma2
AdvancedPM=no

je viens de compiler un nouveau kernel 2.6.24-5-generic sans faire la config', ce dernier n'a plus besoin de noapic au démarrage, mais les problèmes de modules sont toujours là, et bien sur il n'y a plus d'accelération graphique.

La version 'backport' de Hardy par contre ne peut peut pas en dire autant.

Je vais essayer cette fois en fesant la config', je suis curieux de voir comment le kernel 2.6.24 gère les supports pour fujitsu à travers le menu.

il vaut mieux en tout cas attendre que la version stable de ce noyau sorte sur ubuntu avant de se lancer dans une installation....

Changedman · Le 30/01/2008, à 23:29

patko a écrit :

il vaut mieux en tout cas attendre que la version stable de ce noyau sorte sur ubuntu avant de se lancer dans une installation....

Je ne peux me résoudre à attendre encore 4 mois pour me remettre à GNU/Linux, j'essaierai la première distribution integrant le kernel 2.6.24 final et je rapporterai mes résultats. Une partition toute fraiche est prête et n'attend que cela.

patko · Le 01/02/2008, à 17:47

Changedman a écrit :

patko a écrit :
il vaut mieux en tout cas attendre que la version stable de ce noyau sorte sur ubuntu avant de se lancer dans une installation....
Je ne peux me résoudre à attendre encore 4 mois pour me remettre à GNU/Linux, j'essaierai la première distribution integrant le kernel 2.6.24 final et je rapporterai mes résultats. Une partition toute fraiche est prête et n'attend que cela.

Je ne peux pas non plus me résoudre à attendre, j'ai donc compilé le nouveau kernel, en enlevant toutes les dernières options afin d'éviter un kernel panic.

voici mon dmesg:

[ 0.000000] Linux version 2.6.24 (root@amilo) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP PREEMPT Fri Feb 1 01:59:04 CET 2008
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
[ 0.000000] BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000ce000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007ff60000 (usable)
[ 0.000000] BIOS-e820: 000000007ff60000 - 000000007ff6a000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007ff6a000 - 000000007ff80000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007ff80000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] 1151MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000f79d0
[ 0.000000] Entering add_active_range(0, 0, 524128) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 524128
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 524128
[ 0.000000] On node 0 totalpages: 524128
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 2302 pages used for memmap
[ 0.000000] HighMem zone: 292450 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP 000F7A10, 0014 (r0 PTLTD )
[ 0.000000] ACPI: RSDT 7FF64FA3, 0040 (r1 FSC PC 6040000 LTP 0)
[ 0.000000] ACPI: FACP 7FF69B58, 0074 (r1 NVIDIA MCP51M 6040000 PTL_ F4240)
[ 0.000000] ACPI: DSDT 7FF64FE3, 4B75 (r1 FIC XTB71___ 6040000 MSFT 100000E)
[ 0.000000] ACPI: FACS 7FF6AFC0, 0040
[ 0.000000] ACPI: SLIC 7FF69BCC, 0176 (r1 FSC PC 6040000 LOHR 5A)
[ 0.000000] ACPI: SSDT 7FF69D42, 01C4 (r1 PTLTD POWERNOW 6040000 LTP 1)
[ 0.000000] ACPI: MCFG 7FF69F06, 003C (r1 PTLTD MCFG 6040000 LTP 0)
[ 0.000000] ACPI: HPET 7FF69F42, 0038 (r1 PTLTD HPETTBL 6040000 LTP 1)
[ 0.000000] ACPI: APIC 7FF69F7A, 005E (r1 PTLTD APIC 6040000 LTP 0)
[ 0.000000] ACPI: BOOT 7FF69FD8, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP 1)
[ 0.000000] ACPI: DMI detected: Fujitsu Siemens
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:8 APIC version 16
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] Processor #1 15:8 APIC version 16
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfed00000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 520034
[ 0.000000] Kernel command line: root=UUID=0ce9e0a4-4221-43de-b5c2-91d778be655d ro quiet splash pci=usepirqmask pci=routeirq
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 1703.568 MHz processor.
[ 15.498981] spurious 8259A interrupt: IRQ7.
[ 15.501639] Console: colour VGA+ 80x25
[ 15.501643] console [tty0] enabled
[ 15.502006] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 15.502670] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 15.606269] Memory: 2049332k/2096512k available (2007k kernel code, 45844k reserved, 921k data, 316k init, 1179008k highmem)
[ 15.606277] virtual kernel memory layout:
[ 15.606278] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
[ 15.606280] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 15.606281] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 15.606282] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 15.606283] .init : 0xc03e3000 - 0xc0432000 ( 316 kB)
[ 15.606285] .data : 0xc02f5f98 - 0xc03dc664 ( 921 kB)
[ 15.606286] .text : 0xc0100000 - 0xc02f5f98 (2007 kB)
[ 15.606289] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 15.606557] hpet clockevent registered
[ 15.666548] Calibrating delay using timer specific routine.. 3409.38 BogoMIPS (lpj=1704690)
[ 15.666593] Security Framework initialized
[ 15.666600] SELinux: Disabled at boot.
[ 15.666615] Mount-cache hash table entries: 512
[ 15.666752] CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000011f 00000000
[ 15.666762] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 15.666764] CPU: L2 Cache: 256K (64 bytes/line)
[ 15.666767] CPU 0(2) -> Core 0
[ 15.666768] CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000011f 00000000
[ 15.666779] Compat vDSO mapped to ffffe000.
[ 15.666789] Checking 'hlt' instruction... OK.
[ 15.670817] SMP alternatives: switching to UP code
[ 15.671221] ACPI: Core revision 20070126
[ 15.679444] CPU0: AMD Athlon(tm) 64 X2 Dual-Core Processor TK-53 stepping 01
[ 15.679464] SMP alternatives: switching to SMP code
[ 15.679828] Booting processor 1/1 eip 2000
[ 15.754514] Initializing CPU#1
[ 15.783292] Calibrating delay using timer specific routine.. 1603.32 BogoMIPS (lpj=801663)
[ 15.783299] CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000011f 00000000
[ 15.783306] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 15.783308] CPU: L2 Cache: 256K (64 bytes/line)
[ 15.783310] CPU 1(2) -> Core 1
[ 15.783312] AMD C1E detected late. Force timer broadcast.
[ 15.783314] CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000011f 00000000
[ 15.782649] CPU1: AMD Athlon(tm) 64 X2 Dual-Core Processor TK-53 stepping 01
[ 15.782661] Total of 2 processors activated (5012.70 BogoMIPS).
[ 15.782814] ENABLING IO-APIC IRQs
[ 15.782993] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 15.793154] Brought up 2 CPUs
[ 15.793355] net_namespace: 64 bytes
[ 15.793820] NET: Registered protocol family 16
[ 15.794003] EISA bus registered
[ 15.794007] ACPI: bus type pci registered
[ 15.794018] PCI: Using MMCONFIG
[ 15.794042] PCI: No mmconfig possible on device 00:18
[ 15.794153] PCI: No mmconfig possible on device 07:06
[ 15.794300] Setting up standard PCI resources
[ 15.795986] ACPI: EC: Look up EC in DSDT
[ 15.798039] ACPI: Interpreter enabled
[ 15.798042] ACPI: (supports S0 S5)
[ 15.798049] ACPI: Using IOAPIC for interrupt routing
[ 15.803836] ACPI: EC: GPE = 0x2, I/O: command/status = 0x66, data = 0x62
[ 15.803840] ACPI: EC: driver started in poll mode
[ 15.803907] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 15.804774] PCI: Transparent bridge - 0000:00:10.0
[ 15.804795] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 15.804881] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
[ 15.804898] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR0._PRT]
[ 15.804927] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR1._PRT]
[ 15.804954] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR2._PRT]
[ 15.827982] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 10 11 14 15) *0, disabled.
[ 15.828170] ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 10 *11 14 15)
[ 15.828355] ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 10 *11 14 15)
[ 15.828534] ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 10 11 14 15) *0, disabled.
[ 15.828813] ACPI: PCI Interrupt Link [LK1E] (IRQs 16 17 18 19 20 21 22 23) *11
[ 15.828995] ACPI: PCI Interrupt Link [LK2E] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 15.829176] ACPI: PCI Interrupt Link [LK3E] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 15.829359] ACPI: PCI Interrupt Link [LK4E] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 15.829540] ACPI: PCI Interrupt Link [LSMB] (IRQs 16 17 18 19 20 21 22 23) *10
[ 15.829724] ACPI: PCI Interrupt Link [LPMU] (IRQs 16 17 18 19 20 21 22 23) *10
[ 15.829905] ACPI: PCI Interrupt Link [LUS0] (IRQs 16 17 18 19 20 21 22 23) *11
[ 15.830087] ACPI: PCI Interrupt Link [LUS2] (IRQs 16 17 18 19 20 21 22 23) *5
[ 15.830270] ACPI: PCI Interrupt Link [LMAC] (IRQs 16 17 18 19 20 21 22 23) *15
[ 15.830451] ACPI: PCI Interrupt Link [LAZA] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 15.830632] ACPI: PCI Interrupt Link [LPID] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 15.830822] ACPI: PCI Interrupt Link [LTID] (IRQs 16 17 18 19 20 21 22 23) *10
[ 15.831003] ACPI: PCI Interrupt Link [LSI1] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 15.831135] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 15.831165] pnp: PnP ACPI init
[ 15.831174] ACPI: bus type pnp registered
[ 15.833785] pnp: PnP ACPI: found 13 devices
[ 15.833788] ACPI: ACPI bus type pnp unregistered
[ 15.833792] PnPBIOS: Disabled by ACPI PNP
[ 15.833956] PCI: Using ACPI for IRQ routing
[ 15.833960] PCI: Routing PCI interrupts for all devices because "pci=routeirq" specified
[ 15.834225] ACPI: PCI Interrupt Link [LSMB] enabled at IRQ 23
[ 15.834231] ACPI: PCI Interrupt 0000:00:0a.1[A] -> Link [LSMB] -> GSI 23 (level, low) -> IRQ 16
[ 15.834478] ACPI: PCI Interrupt Link [LPMU] enabled at IRQ 22
[ 15.834483] ACPI: PCI Interrupt 0000:00:0a.3[b] -> Link [LPMU] -> GSI 22 (level, low) -> IRQ 17
[ 15.834723] ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 21
[ 15.834729] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LUS0] -> GSI 21 (level, low) -> IRQ 18
[ 15.834972] ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 20
[ 15.834977] ACPI: PCI Interrupt 0000:00:0b.1[b] -> Link [LUS2] -> GSI 20 (level, low) -> IRQ 19
[ 15.835217] ACPI: PCI Interrupt Link [LTID] enabled at IRQ 19
[ 15.835222] ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [LTID] -> GSI 19 (level, low) -> IRQ 20
[ 15.835465] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 18
[ 15.835470] ACPI: PCI Interrupt 0000:00:10.1[b] -> Link [LAZA] -> GSI 18 (level, low) -> IRQ 21
[ 15.835709] ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 17
[ 15.835714] ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [LMAC] -> GSI 17 (level, low) -> IRQ 22
[ 15.835958] ACPI: PCI Interrupt Link [LK1E] enabled at IRQ 16
[ 15.835963] ACPI: PCI Interrupt 0000:05:00.0[A] -> Link [LK1E] -> GSI 16 (level, low) -> IRQ 23
[ 15.836197] ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 11
[ 15.836203] ACPI: PCI Interrupt 0000:07:06.0[A] -> Link [LNK1] -> GSI 11 (level, low) -> IRQ 11
[ 15.838673] NET: Registered protocol family 8
[ 15.838676] NET: Registered protocol family 20
[ 15.838708] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
[ 15.838714] hpet0: 3 32-bit timers, 25000000 Hz
[ 15.839608] Time: hpet clocksource has been installed.
[ 15.839612] Clockevents: could not switch to one-shot mode: lapic is not functional.
[ 15.839616] Could not switch to high resolution mode on CPU 0
[ 15.840916] Clockevents: could not switch to one-shot mode: lapic is not functional.
[ 15.840924] Could not switch to high resolution mode on CPU 1
[ 15.841996] system 00:00: iomem range 0xffc00000-0xffffffff could not be reserved
[ 15.842000] system 00:00: iomem range 0xfec00000-0xfec00fff could not be reserved
[ 15.842003] system 00:00: iomem range 0xfee00000-0xfeefffff could not be reserved
[ 15.842006] system 00:00: iomem range 0xfed00000-0xfed00fff has been reserved
[ 15.842015] system 00:02: iomem range 0xe0000000-0xefffffff could not be reserved
[ 15.842022] system 00:03: ioport range 0x1000-0x107f has been reserved
[ 15.842025] system 00:03: ioport range 0x1080-0x10ff has been reserved
[ 15.842028] system 00:03: ioport range 0x1400-0x147f has been reserved
[ 15.842031] system 00:03: ioport range 0x1480-0x14ff has been reserved
[ 15.842034] system 00:03: ioport range 0x1800-0x187f has been reserved
[ 15.842037] system 00:03: ioport range 0x1880-0x18ff has been reserved
[ 15.842048] system 00:0b: ioport range 0x360-0x361 has been reserved
[ 15.842051] system 00:0b: ioport range 0x4d0-0x4d1 has been reserved
[ 15.856600] PCI: Bridge: 0000:00:02.0
[ 15.856603] IO window: 4000-4fff
[ 15.856607] MEM window: c0200000-c03fffff
[ 15.856609] PREFETCH window: c4200000-c43fffff
[ 15.856612] PCI: Bridge: 0000:00:03.0
[ 15.856614] IO window: disabled.
[ 15.856617] MEM window: disabled.
[ 15.856619] PREFETCH window: disabled.
[ 15.856625] PCI: Failed to allocate mem resource #6:20000@e0000000 for 0000:05:00.0
[ 15.856658] PCI: Bridge: 0000:00:04.0
[ 15.856661] IO window: 5000-5fff
[ 15.856663] MEM window: c1000000-c3ffffff
[ 15.856666] PREFETCH window: d0000000-dfffffff
[ 15.856669] PCI: Bridge: 0000:00:10.0
[ 15.856672] IO window: 6000-6fff
[ 15.856675] MEM window: c4000000-c40fffff
[ 15.856677] PREFETCH window: disabled.
[ 15.856691] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 15.856699] PCI: Setting latency timer of device 0000:00:03.0 to 64
[ 15.856706] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 15.856713] PCI: Setting latency timer of device 0000:00:10.0 to 64
[ 15.856750] NET: Registered protocol family 2
[ 15.862278] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 15.862703] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 15.863550] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[ 15.864131] TCP: Hash tables configured (established 131072 bind 65536)
[ 15.864134] TCP reno registered
[ 15.866117] Unpacking initramfs...<4>Clocksource tsc unstable (delta = -264622005 ns)
[ 17.049784] done
[ 17.068359] Freeing initrd memory: 24768k freed
[ 17.068474] Simple Boot Flag at 0x36 set to 0x1
[ 17.070203] audit: initializing netlink socket (disabled)
[ 17.070217] audit(1201881617.886:1): initialized
[ 17.070361] highmem bounce pool size: 64 pages
[ 17.070450] VFS: Disk quotas dquot_6.5.1
[ 17.070475] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 17.070556] io scheduler noop registered
[ 17.070558] io scheduler anticipatory registered
[ 17.070561] io scheduler deadline registered
[ 17.070574] io scheduler cfq registered (default)
[ 17.170781] Boot video device is 0000:05:00.0
[ 17.170894] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 17.170915] assign_interrupt_mode Found MSI capability
[ 17.170932] Allocate Port Service[0000:00:02.0:pcie00]
[ 17.170967] Allocate Port Service[0000:00:02.0:pcie02]
[ 17.171000] Allocate Port Service[0000:00:02.0:pcie03]
[ 17.171055] PCI: Setting latency timer of device 0000:00:03.0 to 64
[ 17.171073] assign_interrupt_mode Found MSI capability
[ 17.171086] Allocate Port Service[0000:00:03.0:pcie00]
[ 17.171120] Allocate Port Service[0000:00:03.0:pcie02]
[ 17.171153] Allocate Port Service[0000:00:03.0:pcie03]
[ 17.171208] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 17.171232] assign_interrupt_mode Found MSI capability
[ 17.171244] Allocate Port Service[0000:00:04.0:pcie00]
[ 17.171279] Allocate Port Service[0000:00:04.0:pcie03]
[ 17.171488] isapnp: Scanning for PnP cards...
[ 17.339399] isapnp: No Plug & Play device found
[ 17.364046] Real Time Clock Driver v1.12ac
[ 17.364261] hpet_resources: 0xfed00000 is busy
[ 17.364304] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 17.365024] input: Macintosh mouse button emulation as /class/input/input0
[ 17.365122] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
[ 17.368978] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 17.370962] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 17.370968] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 17.370971] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 17.370974] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 17.370977] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 17.372201] mice: PS/2 mouse device common for all mice
[ 17.372324] EISA: Probing bus 0 at eisa.0
[ 17.372329] Cannot allocate resource for EISA slot 1
[ 17.372334] Cannot allocate resource for EISA slot 3
[ 17.372337] Cannot allocate resource for EISA slot 4
[ 17.372340] Cannot allocate resource for EISA slot 5
[ 17.372342] Cannot allocate resource for EISA slot 6
[ 17.372349] EISA: Detected 0 cards.
[ 17.372458] TCP cubic registered
[ 17.372469] NET: Registered protocol family 1
[ 17.372499] Using IPI No-Shortcut mode
[ 17.372832] Freeing unused kernel memory: 316k freed
[ 17.399427] input: AT Translated Set 2 keyboard as /class/input/input1
[ 18.100635] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 18.100641] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 18.101462] Probing IDE interface ide0...
[ 18.347376] hdb: probing with STATUS(0x00) instead of ALTSTATUS(0xff)
[ 18.395387] hdb: IRQ probe failed (0xff7fecfc)
[ 18.476769] hdb: probing with STATUS(0x00) instead of ALTSTATUS(0xff)
[ 18.524775] hdb: IRQ probe failed (0xff7fecfc)
[ 18.678141] hda: probing with STATUS(0x50) instead of ALTSTATUS(0xff)
[ 18.750126] hda: probing with STATUS(0x51) instead of ALTSTATUS(0xff)
[ 18.870103] hda: probing with STATUS(0x51) instead of ALTSTATUS(0xff)
[ 18.918219] hda: Optiarc DVD RW AD-7540A, ATAPI CD/DVD-ROM drive
[ 18.918240] Probing IDE interface ide1...
[ 19.167012] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 19.181828] SCSI subsystem initialized
[ 19.183985] Driver 'sd' needs updating - please use bus_type methods
[ 19.207320] ACPI: Thermal Zone [THRM] (53 C)
[ 20.125928] usbcore: registered new interface driver usbfs
[ 20.125955] usbcore: registered new interface driver hub
[ 20.125988] usbcore: registered new device driver usb
[ 20.136885] NFORCE-MCP51: IDE controller (0x10de:0x0265 rev 0xf1) at PCI slot 0000:00:0d.0
[ 20.136907] NFORCE-MCP51: not 100% native mode: will probe irqs later
[ 20.136912] NFORCE-MCP51: BIOS didn't set cable bits correctly. Enabling workaround.
[ 20.136916] NFORCE-MCP51: 0000:00:0d.0 (rev f1) UDMA133 controller
[ 20.136920] NFORCE-MCP51: port 0x01f0 already claimed by ide0
[ 20.136926] ide1: BM-DMA at 0x3088-0x308f, BIOS settings: hdc:DMA, hdd:pio
[ 20.136934] Probing IDE interface ide1...
[ 20.156974] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 20.156978] ohci_hcd: block sizes: ed 64 td 64
[ 20.158879] libata version 3.00 loaded.
[ 20.158926] ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
[ 20.386017] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LUS0] -> GSI 21 (level, low) -> IRQ 18
[ 20.386030] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[ 20.386034] ohci_hcd 0000:00:0b.0: OHCI Host Controller
[ 20.386196] drivers/usb/core/inode.c: creating file 'devices'
[ 20.386201] drivers/usb/core/inode.c: creating file '001'
[ 20.386206] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1
[ 20.386219] ohci_hcd 0000:00:0b.0: created debug files
[ 20.386229] ohci_hcd 0000:00:0b.0: irq 18, io mem 0xc0004000
[ 20.412071] ohci_hcd 0000:00:0b.0: OHCI controller state
[ 20.412077] ohci_hcd 0000:00:0b.0: OHCI 1.0, NO legacy support registers
[ 20.412081] ohci_hcd 0000:00:0b.0: control 0x683 RWE RWC HCFS=operational CBSR=3
[ 20.412084] ohci_hcd 0000:00:0b.0: cmdstatus 0x00000 SOC=0
[ 20.412088] ohci_hcd 0000:00:0b.0: intrstatus 0x00000044 RHSC SF
[ 20.412091] ohci_hcd 0000:00:0b.0: intrenable 0x8000000a MIE RD WDH
[ 20.412097] ohci_hcd 0000:00:0b.0: hcca frame #0005
[ 20.412101] ohci_hcd 0000:00:0b.0: roothub.a 01000208 POTPGT=1 NPS NDP=8(8)
[ 20.412104] ohci_hcd 0000:00:0b.0: roothub.b 00000000 PPCM=0000 DR=0000
[ 20.412107] ohci_hcd 0000:00:0b.0: roothub.status 00008000 DRWE
[ 20.412111] ohci_hcd 0000:00:0b.0: roothub.portstatus [0] 0x00000100 PPS
[ 20.412115] ohci_hcd 0000:00:0b.0: roothub.portstatus [1] 0x00010301 CSC LSDA PPS CCS
[ 20.412119] ohci_hcd 0000:00:0b.0: roothub.portstatus [2] 0x00010101 CSC PPS CCS
[ 20.412123] ohci_hcd 0000:00:0b.0: roothub.portstatus [3] 0x00000100 PPS
[ 20.412126] ohci_hcd 0000:00:0b.0: roothub.portstatus [4] 0x00000100 PPS
[ 20.412130] ohci_hcd 0000:00:0b.0: roothub.portstatus [5] 0x00000100 PPS
[ 20.412133] ohci_hcd 0000:00:0b.0: roothub.portstatus [6] 0x00010101 CSC PPS CCS
[ 20.412137] ohci_hcd 0000:00:0b.0: roothub.portstatus [7] 0x00000100 PPS
[ 20.412154] usb usb1: default language 0x0409
[ 20.412186] usb usb1: uevent
[ 20.412201] usb usb1: usb_probe_device
[ 20.412274] usb usb1: configuration #1 chosen from 1 choice
[ 20.412280] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[ 20.412291] usb 1-0:1.0: uevent
[ 20.412303] hub 1-0:1.0: usb_probe_interface
[ 20.412305] hub 1-0:1.0: usb_probe_interface - got id
[ 20.412308] hub 1-0:1.0: USB hub found
[ 20.412317] hub 1-0:1.0: 8 ports detected
[ 20.412319] hub 1-0:1.0: standalone hub
[ 20.412320] hub 1-0:1.0: no power switching (usb 1.0)
[ 20.412323] hub 1-0:1.0: global over-current protection
[ 20.412326] hub 1-0:1.0: power on to power good time: 2ms
[ 20.412331] hub 1-0:1.0: local power source is good
[ 20.412333] hub 1-0:1.0: no over-current condition exists
[ 20.412336] hub 1-0:1.0: trying to enable port power on non-switchable hub
[ 20.460526] hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0000
[ 20.459541] drivers/usb/core/inode.c: creating file '001'
[ 20.459554] usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
[ 20.459557] usb usb1: Product: OHCI Host Controller
[ 20.459559] usb usb1: Manufacturer: Linux 2.6.24 ohci_hcd
[ 20.459561] usb usb1: SerialNumber: 0000:00:0b.0
[ 20.460618] ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [1] = 0x00010301 CSC LSDA PPS CCS
[ 20.460624] hub 1-0:1.0: port 2, status 0301, change 0001, 1.5 Mb/s
[ 20.459769] ACPI: PCI Interrupt 0000:00:0b.1[b] -> Link [LUS2] -> GSI 20 (level, low) -> IRQ 19
[ 20.459780] PCI: Setting latency timer of device 0000:00:0b.1 to 64
[ 20.459784] ehci_hcd 0000:00:0b.1: EHCI Host Controller
[ 20.459806] drivers/usb/core/inode.c: creating file '002'
[ 20.459812] ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2
[ 20.459820] ehci_hcd 0000:00:0b.1: reset hcs_params 0x101888 dbg=1 cc=1 pcc=8 !ppc ports=8
[ 20.459827] ehci_hcd 0000:00:0b.1: reset portroute 0 0 0 0 0 0 0 0
[ 20.459830] ehci_hcd 0000:00:0b.1: reset hcc_params a086 caching frame 256/512/1024 park
[ 20.459852] ehci_hcd 0000:00:0b.1: park 0
[ 20.459857] ehci_hcd 0000:00:0b.1: reset command 080b32 park=3 ithresh=8 Async Periodic period=1024 Reset HALT
[ 20.459868] ehci_hcd 0000:00:0b.1: debug port 1
[ 20.459872] PCI: cache line size of 64 is not supported by device 0000:00:0b.1
[ 20.459874] ehci_hcd 0000:00:0b.1: supports USB remote wakeup
[ 20.459885] ehci_hcd 0000:00:0b.1: irq 19, io mem 0xc0005000
[ 20.459890] ehci_hcd 0000:00:0b.1: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT
[ 20.459896] ehci_hcd 0000:00:0b.1: init command 010009 (park)=0 ithresh=1 period=256 RUN
[ 20.462288] ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 20.462315] usb usb2: default language 0x0409
[ 20.462346] usb usb2: uevent
[ 20.462360] usb usb2: usb_probe_device
[ 20.462417] usb usb2: configuration #1 chosen from 1 choice
[ 20.462423] usb usb2: adding 2-0:1.0 (config #1, interface 0)
[ 20.462434] usb 2-0:1.0: uevent
[ 20.462446] hub 2-0:1.0: usb_probe_interface
[ 20.462448] hub 2-0:1.0: usb_probe_interface - got id
[ 20.462451] hub 2-0:1.0: USB hub found
[ 20.462459] hub 2-0:1.0: 8 ports detected
[ 20.462461] hub 2-0:1.0: standalone hub
[ 20.462463] hub 2-0:1.0: no power switching (usb 1.0)
[ 20.462466] hub 2-0:1.0: individual port over-current protection
[ 20.462468] hub 2-0:1.0: Single TT
[ 20.462470] hub 2-0:1.0: TT requires at most 8 FS bit times (666 ns)
[ 20.462473] hub 2-0:1.0: power on to power good time: 20ms
[ 20.462477] hub 2-0:1.0: local power source is good
[ 20.462480] hub 2-0:1.0: trying to enable port power on non-switchable hub
[ 20.473224] ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [1] = 0x00010300 CSC LSDA PPS
[ 20.509887] drivers/usb/core/inode.c: creating file '001'
[ 20.509898] usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
[ 20.509901] usb usb2: Product: EHCI Host Controller
[ 20.509904] usb usb2: Manufacturer: Linux 2.6.24 ehci_hcd
[ 20.509906] usb usb2: SerialNumber: 0000:00:0b.1
[ 20.511356] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61.
[ 20.511380] ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [LMAC] -> GSI 17 (level, low) -> IRQ 22
[ 20.511387] PCI: Setting latency timer of device 0000:00:14.0 to 64
[ 20.523572] hub 1-0:1.0: debounce: port 2: total 125ms stable 100ms status 0x300
[ 20.523580] ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [2] = 0x00010100 CSC PPS
[ 20.523587] hub 1-0:1.0: port 3, status 0100, change 0001, 12 Mb/s
[ 20.574377] hub 1-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x100
[ 20.574390] ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [6] = 0x00010100 CSC PPS
[ 20.574396] hub 1-0:1.0: port 7, status 0100, change 0001, 12 Mb/s
[ 20.625191] hub 1-0:1.0: debounce: port 7: total 100ms stable 100ms status 0x100
[ 20.625198] hub 1-0:1.0: state 7 ports 8 chg 0000 evt fe00
[ 20.625203] usb usb1: remote wakeup needed for autosuspend
[ 20.625206] hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0000
[ 20.625215] ehci_hcd 0000:00:0b.1: GetStatus port 2 status 001403 POWER sig=k CSC CONNECT
[ 20.625221] hub 2-0:1.0: port 2, status 0501, change 0001, 480 Mb/s
[ 20.675533] hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x501
[ 20.675543] ehci_hcd 0000:00:0b.1: port 2 low speed --> companion
[ 20.700003] ehci_hcd 0000:00:0b.1: GetStatus port 2 status 003402 POWER OWNER sig=k CSC
[ 20.700020] ehci_hcd 0000:00:0b.1: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT
[ 20.700026] hub 2-0:1.0: port 3, status 0501, change 0001, 480 Mb/s
[ 20.750812] hub 2-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501
[ 20.753506] forcedeth 0000:00:14.0: ifname eth0, PHY OUI 0x5043 @ 1, addr 00:14:0b:3d:15:3b
[ 20.753510] forcedeth 0000:00:14.0: highdma pwrctl timirq gbit lnktim desc-v3
[ 20.752521] ACPI: PCI Interrupt 0000:07:06.0[A] -> Link [LNK1] -> GSI 11 (level, low) -> IRQ 11
[ 20.774905] ehci_hcd 0000:00:0b.1: port 3 high speed
[ 20.774912] ehci_hcd 0000:00:0b.1: GetStatus port 3 status 001005 POWER sig=se0 PE CONNECT
[ 20.798802] usb 2-3: new high speed USB device using ehci_hcd and address 3
[ 20.804987] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[c4000000-c40007ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 20.816070] sata_nv 0000:00:0e.0: version 3.5
[ 20.816089] PCI: Enabling device 0000:00:0e.0 (0005 -> 0007)
[ 20.816095] ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [LTID] -> GSI 19 (level, low) -> IRQ 20
[ 20.816138] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[ 20.816213] scsi0 : sata_nv
[ 20.816850] scsi1 : sata_nv
[ 20.817002] ata1: SATA max UDMA/133 cmd 0x30b0 ctl 0x30a4 bmdma 0x3090 irq 20
[ 20.817005] ata2: SATA max UDMA/133 cmd 0x30a8 ctl 0x30a0 bmdma 0x3098 irq 20
[ 20.827622] ehci_hcd 0000:00:0b.1: port 3 high speed
[ 20.827627] ehci_hcd 0000:00:0b.1: GetStatus port 3 status 001005 POWER sig=se0 PE CONNECT
[ 20.858284] usb 2-3: uevent
[ 20.858303] usb 2-3: usb_probe_device
[ 20.858357] usb 2-3: configuration #1 chosen from 1 choice
[ 20.858426] usb 2-3: adding 2-3:1.0 (config #1, interface 0)
[ 20.858436] usb 2-3:1.0: uevent
[ 20.858609] drivers/usb/core/inode.c: creating file '003'
[ 20.858619] usb 2-3: new device strings: Mfr=0, Product=0, SerialNumber=0
[ 20.858631] ehci_hcd 0000:00:0b.1: GetStatus port 7 status 001803 POWER sig=j CSC CONNECT
[ 20.858637] hub 2-0:1.0: port 7, status 0501, change 0001, 480 Mb/s
[ 20.908900] hub 2-0:1.0: debounce: port 7: total 100ms stable 100ms status 0x501
[ 20.933374] ehci_hcd 0000:00:0b.1: port 7 full speed --> companion
[ 20.933380] ehci_hcd 0000:00:0b.1: GetStatus port 7 status 003001 POWER OWNER sig=se0 CONNECT
[ 20.933398] hub 2-0:1.0: port 7 not reset yet, waiting 50ms
[ 20.957831] ehci_hcd 0000:00:0b.1: GetStatus port 7 status 003802 POWER OWNER sig=j CSC
[ 20.957849] hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0004
[ 20.957856] ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [1] = 0x00010301 CSC LSDA PPS CCS
[ 20.957861] hub 1-0:1.0: port 2, status 0301, change 0001, 1.5 Mb/s
[ 21.008645] hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x301
[ 21.029252] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 21.061342] ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA PPS PES CCS
[ 21.085811] usb 1-2: new low speed USB device using ohci_hcd and address 2
[ 21.138977] ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA PPS PES CCS
[ 21.174788] usb 1-2: skipped 1 descriptor after interface
[ 21.176190] usb 1-2: default language 0x0409
[ 21.178098] usb 1-2: uevent
[ 21.178115] usb 1-2: usb_probe_device
[ 21.178168] usb 1-2: configuration #1 chosen from 1 choice
[ 21.179491] usb 1-2: adding 1-2:1.0 (config #1, interface 0)
[ 21.179515] usb 1-2:1.0: uevent
[ 21.179585] drivers/usb/core/inode.c: creating file '002'
[ 21.179596] usb 1-2: new device strings: Mfr=0, Product=2, SerialNumber=0
[ 21.179599] usb 1-2: Product: PS/2+USB Mouse
[ 21.179607] ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [6] = 0x00010101 CSC PPS CCS
[ 21.179613] hub 1-0:1.0: port 7, status 0101, change 0001, 12 Mb/s
[ 21.196928] ata1.00: ATA-7: WDC WD1600BEVS-07RST0, 04.01G04, max UDMA/133
[ 21.196933] ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 21.201057] ata1.00: configured for UDMA/133
[ 21.229831] hub 1-0:1.0: debounce: port 7: total 100ms stable 100ms status 0x101
[ 21.282479] ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [6] = 0x00100103 PRSC PPS PES CCS
[ 21.307879] usb 1-7: new full speed USB device using ohci_hcd and address 3
[ 21.343528] ata2: SATA link down (SStatus 0 SControl 300)
[ 21.355055] scsi 0:0:0:0: Direct-Access ATA WDC WD1600BEVS-0 04.0 PQ: 0 ANSI: 5
[ 21.355139] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 21.355151] sd 0:0:0:0: [sda] Write Protect is off
[ 21.355153] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 21.355168] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 21.355223] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 21.355232] sd 0:0:0:0: [sda] Write Protect is off
[ 21.355234] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 21.355248] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 21.355253] sda: sda1 sda2 <<7>ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [6] = 0x00100103 PRSC PPS PES CCS
[ 21.382712] sda5 sda6 > sda3 sda4
[ 21.387916] sd 0:0:0:0: [sda] Attached SCSI disk
[ 21.397859] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 21.415842] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0040ca014e01c051]
[ 21.418486] ieee1394: Node added: ID:BUS[0-01:1023] GUID[0014960001000381]
[ 21.426075] usb 1-7: uevent
[ 21.426094] usb 1-7: usb_probe_device
[ 21.426149] usb 1-7: configuration #1 chosen from 1 choice
[ 21.427447] usb 1-7: adding 1-7:1.0 (config #1, interface 0)
[ 21.427464] usb 1-7:1.0: uevent
[ 21.427546] usb 1-7: adding 1-7:1.1 (config #1, interface 1)
[ 21.427556] usb 1-7:1.1: uevent
[ 21.427631] drivers/usb/core/inode.c: creating file '003'
[ 21.427643] usb 1-7: new device strings: Mfr=0, Product=0, SerialNumber=0
[ 21.427654] hub 2-0:1.0: state 7 ports 8 chg 0000 evt fe80
[ 21.427661] hub 1-0:1.0: state 7 ports 8 chg 0000 evt fe80
[ 21.660761] EXT3-fs: mounted filesystem with ordered data mode.
[ 21.660828] kjournald starting. Commit interval 5 seconds
[ 23.267494] ide-cd: cmd 0x5a timed out
[ 23.267502] hda: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
[ 23.267507] ide: failed opcode was: unknown
[ 23.267519] hda: ATAPI CD-ROM drive, 0kB Cache
[ 23.267523] Uniform CD-ROM driver Revision: 3.20
[ 23.267541] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 23.267544] ide: failed opcode was: unknown
[ 23.267547] hda: drive not ready for command
[ 23.267562] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 23.267565] ide: failed opcode was: unknown
[ 23.267567] hda: drive not ready for command
[ 23.267580] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 23.267584] ide: failed opcode was: unknown
[ 23.267616] hda: drive not ready for command
[ 23.267629] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 23.267632] ide: failed opcode was: unknown
[ 23.267634] hda: drive not ready for command
[ 23.267647] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 23.267651] ide: failed opcode was: unknown
[ 23.267653] hda: drive not ready for command
[ 23.267666] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 23.267670] ide: failed opcode was: unknown
[ 23.267672] hda: drive not ready for command
[ 23.267685] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 23.267688] ide: failed opcode was: unknown
[ 23.267690] hda: drive not ready for command
[ 24.138731] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 24.138737] ide: failed opcode was: unknown
[ 24.138741] hda: drive not ready for command
[ 24.138774] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 24.138777] ide: failed opcode was: unknown
[ 24.138779] hda: drive not ready for command
[ 24.144725] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 24.144731] ide: failed opcode was: unknown
[ 24.144735] hda: drive not ready for command
[ 24.170932] usb usb1: uevent
[ 24.170958] usb 1-0:1.0: uevent
[ 24.170983] usb 1-2: uevent
[ 24.171006] usb 1-2:1.0: uevent
[ 24.171030] usb 1-7: uevent
[ 24.171051] usb 1-7:1.0: uevent
[ 24.171075] usb 1-7:1.1: uevent
[ 24.171119] usb usb2: uevent
[ 24.171140] usb 2-0:1.0: uevent
[ 24.171164] usb 2-3: uevent
[ 24.171186] usb 2-3:1.0: uevent
[ 24.537994] ieee1394: raw1394: /dev/raw1394 device initialized
[ 24.548670] NOTE: The dv1394 driver is unsupported and may be removed in a future Linux release. Use raw1394 instead.
[ 25.044860] NET: Registered protocol family 17
[ 25.501230] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 25.531187] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 25.548262] input: Power Button (FF) as /class/input/input2
[ 25.559368] ACPI: Power Button (FF) [PWRF]
[ 25.559462] input: Power Button (CM) as /class/input/input3
[ 25.564529] ACPI: Power Button (CM) [PWRB]
[ 25.564595] input: Sleep Button (CM) as /class/input/input4
[ 25.569734] ACPI: Sleep Button (CM) [SLPB]
[ 25.569837] input: Lid Switch as /class/input/input5
[ 25.572576] ACPI: Lid Switch [LID]
[ 25.638027] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x3040
[ 25.638057] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x3000
[ 25.794588] ACPI: AC Adapter [ACAD] (on-line)
[ 25.911522] ACPI: Battery Slot [BAT0] (battery present)
[ 26.244957] input: PC Speaker as /class/input/input6
[ 26.566133] input: PS/2 Mouse as /class/input/input7
[ 26.583956] input: AlpsPS/2 ALPS GlidePoint as /class/input/input8
[ 26.650656] ACPI: PCI Interrupt 0000:00:10.1[b] -> Link [LAZA] -> GSI 18 (level, low) -> IRQ 21
[ 26.650682] PCI: Setting latency timer of device 0000:00:10.1 to 64
[ 26.685675] hda_codec: Unknown model for ALC882, trying auto-probe from BIOS...
[ 26.704490] hda-codec: No codec parser is available
[ 27.065982] Adding 3903752k swap on /dev/sda5. Priority:-1 extents:1 across:3903752k
[ 27.244330] EXT3 FS on sda6, internal journal
[ 27.898469] kjournald starting. Commit interval 5 seconds
[ 27.899764] EXT3 FS on sda1, internal journal
[ 27.899771] EXT3-fs: mounted filesystem with ordered data mode.
[ 27.923834] kjournald starting. Commit interval 5 seconds
[ 27.925051] EXT3 FS on sda4, internal journal
[ 27.925056] EXT3-fs: mounted filesystem with ordered data mode.
[ 27.971313] NTFS driver 2.1.29 [Flags: R/O MODULE].
[ 28.027024] NTFS volume version 3.1.
[ 28.193973] NET: Registered protocol family 10
[ 28.194221] lo: Disabled Privacy Extensions
[ 29.413419] No dock devices found.
[ 29.446801] toshiba_acpi: Unknown parameter `hotkeys_over_acpi'
[ 29.660630] powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual-Core Processor TK-53 processors (2 cpu cores) (version 2.20.00)
[ 29.659850] powernow-k8: 0 : fid 0x9 (1700 MHz), vid 0x13
[ 29.659855] powernow-k8: 1 : fid 0x8 (1600 MHz), vid 0x14
[ 29.659858] powernow-k8: 2 : fid 0x0 (800 MHz), vid 0x1a
[ 30.652689] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 30.652699] ide: failed opcode was: unknown
[ 30.652703] hda: drive not ready for command
[ 30.652775] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 30.652779] ide: failed opcode was: unknown
[ 30.652781] hda: drive not ready for command
[ 30.652818] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 30.652822] ide: failed opcode was: unknown
[ 30.652824] hda: drive not ready for command
[ 30.652899] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 30.652903] ide: failed opcode was: unknown
[ 30.652905] hda: drive not ready for command
[ 30.652928] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 30.652931] ide: failed opcode was: unknown
[ 30.652933] hda: drive not ready for command
[ 30.974603] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 30.974613] ide: failed opcode was: unknown
[ 30.974620] hda: drive not ready for command
[ 30.974637] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 30.974642] ide: failed opcode was: unknown
[ 30.974647] hda: drive not ready for command
[ 30.974663] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 30.974668] ide: failed opcode was: unknown
[ 30.974672] hda: drive not ready for command
[ 30.974688] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 30.974693] ide: failed opcode was: unknown
[ 30.974698] hda: drive not ready for command
[ 30.974735] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 30.974742] ide: failed opcode was: unknown
[ 30.974746] hda: drive not ready for command
[ 30.974751] cdrom: This disc doesn't have any tracks I recognize!
[ 30.974797] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 30.974802] ide: failed opcode was: unknown
[ 30.974805] hda: drive not ready for command
[ 30.974832] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 30.974838] ide: failed opcode was: unknown
[ 30.974842] hda: drive not ready for command
[ 30.974861] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 30.974868] ide: failed opcode was: unknown
[ 30.974872] hda: drive not ready for command
[ 30.974891] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 30.974896] ide: failed opcode was: unknown
[ 30.974900] hda: drive not ready for command
[ 30.974915] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 30.974920] ide: failed opcode was: unknown
[ 30.974924] hda: drive not ready for command
[ 30.974939] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 30.974945] ide: failed opcode was: unknown
[ 30.974948] hda: drive not ready for command
[ 30.974963] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 30.974967] ide: failed opcode was: unknown
[ 30.974971] hda: drive not ready for command
[ 30.974987] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 30.974991] ide: failed opcode was: unknown
[ 30.974995] hda: drive not ready for command
[ 30.975011] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 30.975016] ide: failed opcode was: unknown
[ 30.975020] hda: drive not ready for command
[ 30.975035] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 30.975040] ide: failed opcode was: unknown
[ 30.975043] hda: drive not ready for command
[ 31.626132] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 31.626141] ide: failed opcode was: unknown
[ 31.626145] hda: drive not ready for command
[ 31.626174] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 31.626178] ide: failed opcode was: unknown
[ 31.626180] hda: drive not ready for command
[ 31.626200] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 31.626204] ide: failed opcode was: unknown
[ 31.626206] hda: drive not ready for command
[ 31.626226] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 31.626229] ide: failed opcode was: unknown
[ 31.626231] hda: drive not ready for command
[ 31.626263] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 31.626266] ide: failed opcode was: unknown
[ 31.626269] hda: drive not ready for command
[ 32.565510] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 32.565517] ide: failed opcode was: unknown
[ 32.565522] hda: drive not ready for command
[ 32.565549] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 32.565552] ide: failed opcode was: unknown
[ 32.565555] hda: drive not ready for command
[ 32.565576] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 32.565580] ide: failed opcode was: unknown
[ 32.565582] hda: drive not ready for command
[ 32.565616] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 32.565620] ide: failed opcode was: unknown
[ 32.565622] hda: drive not ready for command
[ 33.086369] eth0: no IPv6 routers present
[ 33.506487] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 33.506495] ide: failed opcode was: unknown
[ 33.506500] hda: drive not ready for command
[ 33.506524] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 33.506528] ide: failed opcode was: unknown
[ 33.506533] hda: drive not ready for command
[ 33.506553] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 33.506559] ide: failed opcode was: unknown
[ 33.506564] hda: drive not ready for command
[ 33.506590] hda: status error: status=0x58 { DriveReady SeekComplete DataRequest }
[ 33.506596] ide: failed opcode was: unknown
[ 33.506601] hda: drive not ready for command
[ 41.675708] Bluetooth: Core ver 2.11
[ 41.676089] NET: Registered protocol family 31
[ 41.676305] Bluetooth: HCI device and connection manager initialized
[ 41.676573] Bluetooth: HCI socket layer initialized
[ 41.693315] Bluetooth: L2CAP ver 2.9
[ 41.693322] Bluetooth: L2CAP socket layer initialized
[ 41.702753] Bluetooth: RFCOMM socket layer initialized
[ 41.702770] Bluetooth: RFCOMM TTY layer initialized
[ 41.702772] Bluetooth: RFCOMM ver 1.8
[ 64.329977] hda: irq timeout: status=0x51 { DriveReady SeekComplete Error }
[ 64.329985] hda: irq timeout: error=0x64 { AbortedCommand LastFailedSense=0x06 }
[ 64.329989] ide: failed opcode was: unknown

et quelques infos sur ma config:

<b>lspci</b>

00:00.0 RAM memory: nVidia Corporation C51 Host Bridge (rev a2)
00:00.1 RAM memory: nVidia Corporation C51 Memory Controller 0 (rev a2)
00:00.2 RAM memory: nVidia Corporation C51 Memory Controller 1 (rev a2)
00:00.3 RAM memory: nVidia Corporation C51 Memory Controller 5 (rev a2)
00:00.4 RAM memory: nVidia Corporation C51 Memory Controller 4 (rev a2)
00:00.5 RAM memory: nVidia Corporation C51 Host Bridge (rev a2)
00:00.6 RAM memory: nVidia Corporation C51 Memory Controller 3 (rev a2)
00:00.7 RAM memory: nVidia Corporation C51 Memory Controller 2 (rev a2)
00:02.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1)
00:03.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1)
00:04.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1)
00:09.0 RAM memory: nVidia Corporation MCP51 Host Bridge (rev a2)
00:0a.0 ISA bridge: nVidia Corporation MCP51 LPC Bridge (rev a3)
00:0a.1 SMBus: nVidia Corporation MCP51 SMBus (rev a3)
00:0a.3 Co-processor: nVidia Corporation MCP51 PMU (rev a3)
00:0b.0 USB Controller: nVidia Corporation MCP51 USB Controller (rev a3)
00:0b.1 USB Controller: nVidia Corporation MCP51 USB Controller (rev a3)
00:0d.0 IDE interface: nVidia Corporation MCP51 IDE (rev f1)
00:0e.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller (rev f1)
00:10.0 PCI bridge: nVidia Corporation MCP51 PCI Bridge (rev a2)
00:10.1 Audio device: nVidia Corporation MCP51 High Definition Audio (rev a2)
00:14.0 Bridge: nVidia Corporation MCP51 Ethernet Controller (rev a3)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
05:00.0 VGA compatible controller: nVidia Corporation GeForce 8600M GS (rev a1)
07:06.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev c0)

<b>lsmod</b>

Module Size Used by
snd_rtctimer 4640 1
binfmt_misc 13448 1
rfcomm 42384 2
l2cap 26240 11 rfcomm
bluetooth 61412 4 rfcomm,l2cap
powernow_k8 16064 1
cpufreq_powersave 2944 0
cpufreq_ondemand 9868 1
cpufreq_conservative 8968 0
cpufreq_stats 7488 0
freq_table 5920 3 powernow_k8,cpufreq_ondemand,cpufreq_stats
dock 11540 0
sbs 6912 0
sbshc 7936 1 sbs
ipv6 270596 10
nls_cp437 6912 1
ntfs 107712 1
sbp2 24584 0
joydev 13376 0
snd_hda_intel 182300 5
snd_pcm_oss 43264 0
snd_mixer_oss 17664 1 snd_pcm_oss
snd_pcm 80132 4 snd_hda_intel,snd_pcm_oss
snd_seq_dummy 4868 0
serio_raw 8196 0
snd_seq_oss 33664 0
snd_seq_midi 9728 0
snd_rawmidi 25984 1 snd_seq_midi
k8temp 6656 0
psmouse 40592 0
snd_seq_midi_event 8576 2 snd_seq_oss,snd_seq_midi
snd_seq 54000 7 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 24580 3 snd_rtctimer,snd_pcm,snd_seq
snd_seq_device 9484 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
pcspkr 4224 0
snd 55556 18 snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
snd_page_alloc 11528 2 snd_hda_intel,snd_pcm
battery 7296 0
container 5888 0
ac 4992 0
i2c_nforce2 7680 0
i2c_core 25344 1 i2c_nforce2
button 9360 0
shpchp 34708 0
pci_hotplug 32032 1 shpchp
af_packet 23940 2
dv1394 21048 0
raw1394 29272 0
evdev 13312 6
ext3 136968 3
jbd 51732 1 ext3
mbcache 9856 1 ext3
sg 36752 0
sata_nv 28168 5
ohci1394 34224 1 dv1394
ieee1394 94008 4 sbp2,dv1394,raw1394,ohci1394
ata_generic 8580 0
forcedeth 52236 0
ehci_hcd 50956 0
ohci_hcd 41988 0
amd74xx 10384 0 [permanent]
libata 159344 2 sata_nv,ata_generic
usbcore 159212 3 ehci_hcd,ohci_hcd
ssb 32644 1 ohci_hcd
ide_cd 40608 1
cdrom 37024 1 ide_cd
thermal 16924 0
processor 36936 2 powernow_k8,thermal
fan 5892 0
sd_mod 30464 6
scsi_mod 152108 4 sbp2,sg,libata,sd_mod
ide_generic 2304 0 [permanent]
ide_core 113228 3 amd74xx,ide_cd,ide_generic

patko · Le 01/02/2008, à 22:18

j'ai le lecteur cdrom qui fonctionne enfin!!!!!!!!:cool:

lors de la configuration du kernel:

dans la section Device Drivers, ATA,ATAPI,MFM,RLL support, pci IDE chipset support, choisir

AMD and NVIDIA IDE support (j'ai enlevé tous les autres supports de cette sous-section), et dans la section serial ATA, j'ai mis UNIQUEMENT Nvidia SATA support, et ça marche aprés avoir booté sur ce noyau, sans options de démarrage.

J'ai un message d'erreur dans une boite de dialogue aprés avoir lancé gdm à propos de HAL

Le son ne fontionne toujours pas, mais j'ai une petite idée du problème:

le chipset MCP51 dans le kernel pour est indiqué sous la marque intel, j'ai mis uniquement ce module dans le test précedent et ils ont été repèrés et monté, mais toujours pas de son....

pas de wifi

RiFLE+ · Le 02/02/2008, à 15:26

Ayant également le même problème auquel faire face avec ce modèle de PC portable, j'ai besoin d'un Linux Debian fonctionnel, et ce le plus rapidement (projet scolaire). M'étant aperçu que l'opération est quasi-....impossible en installation "normale", j'ai essayé diverses solutions :

-lancement d'un kubuntu à partir d'une clé USB (assez fastidieux) => le résultat est que le Linux s'est installé, cependant il m'est impossible de le lancer au démarrage du PC. Après avoir édité le programme de boot de Vista, celui-ci m'indique lorsque je choisi de lancer Linux que le secteur n'exite pas

-installation de kubuntu et de debian simple en utilisant VirtualBox => cette fois-ci encore le lancement du live fonctionne plutà´t bien (même si il met assez longtemps à se lancer à cause des multiples erreurs repérées dans ce topic). Mais encore une fois, impossible de l'installer : en utilisant hda1 en secteur primaire et hda5 en swap, l'installation me rapporte qu'il est impossible de créer le secteur primaire sur le disque.

Voilà , si quelqu'un à réussi à installer une distribution correctement avec VirtualBox, je serai aux anges si il me communiquait sa méthode

RiFLE+ · Le 02/02/2008, à 17:53

Petite mise à jour de ma situation, j'ai changé des options de VirtualBox et ai finalement réussi à installer kUbuntu. Pour ceux qui ont le même problème, passez l'espace disque alloué à votre VirtualBox à Dynamique (il ajustera cet espace à celui requis). Celà dit ca reste bizarre que ceci ai une quelconque influence sur le fait que Linux installe correctement ou non ses partitions, mais enfin ca marche

Maintenant je vais m'atteler à résoudre les problèmes connus

RiFLE+ · Le 02/02/2008, à 19:21

Je rencontre à nouveau un problème lors de l'installation du driver de la carte WiFi. J'ai installé ndiswrapper et le driver qu'a gentillement renseigné NicoLarve. La commande ndiswrapper -l donne net5211 : driver installed.
Cependant à ma grande surprise, lorsque la commande iwconfig est exécutée, et bien aucune connection WiFi de détectée.
J'ai lu qu'il était possible d'assigner un matériel au driver manuellement, en utilisant la commande lspc -n, mais il n'y a aucune indication qui me permet d'identifier ma carte WiFi dans ces lignes de matériel.

Quelqu'un aurait-il une solution ?

RiFLE+ · Le 02/02/2008, à 21:49

Bon désolé de faire mon monologue, mais mon controleur WiFi n'apparait pas dans le lspci, et l'installation est plutôt pas facile avec ndiswrapper ! Quelqu'un aurait une idée ?

patko · Le 03/02/2008, à 09:55

c'est encore moi, je me suis fait un kernel qui repère mieux mon matériel, mais chauffe grave, le ventillateur tourne en permence, pourtant regarder mon dmegs, quasiment tout est repèré:

[ 0.000000] Linux version 2.6.24 (root@amilo) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP PREEMPT Sun Feb 3 03:56:22 CET 2008
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
[ 0.000000] BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000ce000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007ff60000 (usable)
[ 0.000000] BIOS-e820: 000000007ff60000 - 000000007ff6a000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007ff6a000 - 000000007ff80000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007ff80000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] 1151MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000f79d0
[ 0.000000] Entering add_active_range(0, 0, 524128) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 524128
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 524128
[ 0.000000] On node 0 totalpages: 524128
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 2302 pages used for memmap
[ 0.000000] HighMem zone: 292450 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP 000F7A10, 0014 (r0 PTLTD )
[ 0.000000] ACPI: RSDT 7FF64FA3, 0040 (r1 FSC PC 6040000 LTP 0)
[ 0.000000] ACPI: FACP 7FF69B58, 0074 (r1 NVIDIA MCP51M 6040000 PTL_ F4240)
[ 0.000000] ACPI: DSDT 7FF64FE3, 4B75 (r1 FIC XTB71___ 6040000 MSFT 100000E)
[ 0.000000] ACPI: FACS 7FF6AFC0, 0040
[ 0.000000] ACPI: SLIC 7FF69BCC, 0176 (r1 FSC PC 6040000 LOHR 5A)
[ 0.000000] ACPI: SSDT 7FF69D42, 01C4 (r1 PTLTD POWERNOW 6040000 LTP 1)
[ 0.000000] ACPI: MCFG 7FF69F06, 003C (r1 PTLTD MCFG 6040000 LTP 0)
[ 0.000000] ACPI: HPET 7FF69F42, 0038 (r1 PTLTD HPETTBL 6040000 LTP 1)
[ 0.000000] ACPI: APIC 7FF69F7A, 005E (r1 PTLTD APIC 6040000 LTP 0)
[ 0.000000] ACPI: BOOT 7FF69FD8, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP 1)
[ 0.000000] ACPI: DMI detected: Fujitsu Siemens
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:8 APIC version 16
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] Processor #1 15:8 APIC version 16
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfed00000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 520034
[ 0.000000] Kernel command line: root=UUID=0ce9e0a4-4221-43de-b5c2-91d778be655d ro quiet splash
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 1703.549 MHz processor.
[ 15.194187] spurious 8259A interrupt: IRQ7.
[ 15.196723] Console: colour VGA+ 80x25
[ 15.196726] console [tty0] enabled
[ 15.197090] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 15.197756] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 15.299473] Memory: 2042300k/2096512k available (2119k kernel code, 52984k reserved, 734k data, 256k init, 1179008k highmem)
[ 15.299482] virtual kernel memory layout:
[ 15.299483] fixmap : 0xfff4d000 - 0xfffff000 ( 712 kB)
[ 15.299484] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 15.299485] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 15.299487] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 15.299488] .init : 0xc03cf000 - 0xc040f000 ( 256 kB)
[ 15.299489] .data : 0xc0311dd8 - 0xc03c96a4 ( 734 kB)
[ 15.299490] .text : 0xc0100000 - 0xc0311dd8 (2119 kB)
[ 15.299494] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 15.299760] hpet clockevent registered
[ 15.359751] Calibrating delay using timer specific routine.. 3409.33 BogoMIPS (lpj=1704666)
[ 15.359796] Security Framework initialized
[ 15.359802] SELinux: Disabled at boot.
[ 15.359817] Mount-cache hash table entries: 512
[ 15.359952] CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000011f 00000000
[ 15.359961] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 15.359963] CPU: L2 Cache: 256K (64 bytes/line)
[ 15.359966] CPU 0(2) -> Core 0
[ 15.359967] CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000011f 00000000
[ 15.359977] Compat vDSO mapped to ffffe000.
[ 15.359987] Checking 'hlt' instruction... OK.
[ 15.364001] SMP alternatives: switching to UP code
[ 15.364431] ACPI: Core revision 20070126
[ 15.372648] CPU0: AMD Athlon(tm) 64 X2 Dual-Core Processor TK-53 stepping 01
[ 15.372667] SMP alternatives: switching to SMP code
[ 15.373043] Booting processor 1/1 eip 3000
[ 15.431432] Initializing CPU#1
[ 15.460479] Calibrating delay using timer specific routine.. 1603.32 BogoMIPS (lpj=801662)
[ 15.460485] CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000011f 00000000
[ 15.460491] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 15.460494] CPU: L2 Cache: 256K (64 bytes/line)
[ 15.460496] CPU 1(2) -> Core 1
[ 15.460498] AMD C1E detected late. Force timer broadcast.
[ 15.460499] CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000011f 00000000
[ 15.459794] CPU1: AMD Athlon(tm) 64 X2 Dual-Core Processor TK-53 stepping 01
[ 15.459806] Total of 2 processors activated (5012.65 BogoMIPS).
[ 15.459957] ENABLING IO-APIC IRQs
[ 15.460135] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 15.470292] Brought up 2 CPUs
[ 15.470327] CPU0 attaching sched-domain:
[ 15.470331] domain 0: span 03
[ 15.470333] groups: 01 02
[ 15.470337] CPU1 attaching sched-domain:
[ 15.470338] domain 0: span 03
[ 15.470340] groups: 02 01
[ 15.470548] net_namespace: 64 bytes
[ 15.471098] Time: 8:32:31 Date: 02/03/08
[ 15.471136] NET: Registered protocol family 16
[ 15.471298] ACPI: bus type pci registered
[ 15.471378] PCI: Using MMCONFIG
[ 15.471401] PCI: No mmconfig possible on device 00:18
[ 15.471511] PCI: No mmconfig possible on device 07:06
[ 15.471667] Setting up standard PCI resources
[ 15.473250] ACPI: EC: Look up EC in DSDT
[ 15.475288] ACPI: Interpreter enabled
[ 15.475291] ACPI: (supports S0 S3 S5)
[ 15.475303] ACPI: Using IOAPIC for interrupt routing
[ 15.480888] ACPI: EC: GPE = 0x2, I/O: command/status = 0x66, data = 0x62
[ 15.480892] ACPI: EC: driver started in poll mode
[ 15.480948] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 15.481784] PCI: Transparent bridge - 0000:00:10.0
[ 15.481800] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 15.481887] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
[ 15.481903] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR0._PRT]
[ 15.481936] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR1._PRT]
[ 15.481962] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR2._PRT]
[ 15.504142] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 10 11 14 15) *0, disabled.
[ 15.504319] ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 10 *11 14 15)
[ 15.504490] ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 10 *11 14 15)
[ 15.504664] ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 10 11 14 15) *0, disabled.
[ 15.504834] ACPI: PCI Interrupt Link [LK1E] (IRQs 16 17 18 19 20 21 22 23) *11
[ 15.505008] ACPI: PCI Interrupt Link [LK2E] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 15.505179] ACPI: PCI Interrupt Link [LK3E] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 15.505350] ACPI: PCI Interrupt Link [LK4E] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 15.505524] ACPI: PCI Interrupt Link [LSMB] (IRQs 16 17 18 19 20 21 22 23) *10
[ 15.505695] ACPI: PCI Interrupt Link [LPMU] (IRQs 16 17 18 19 20 21 22 23) *10
[ 15.505867] ACPI: PCI Interrupt Link [LUS0] (IRQs 16 17 18 19 20 21 22 23) *11
[ 15.506041] ACPI: PCI Interrupt Link [LUS2] (IRQs 16 17 18 19 20 21 22 23) *5
[ 15.506212] ACPI: PCI Interrupt Link [LMAC] (IRQs 16 17 18 19 20 21 22 23) *15
[ 15.506383] ACPI: PCI Interrupt Link [LAZA] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 15.506558] ACPI: PCI Interrupt Link [LPID] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 15.506735] ACPI: PCI Interrupt Link [LTID] (IRQs 16 17 18 19 20 21 22 23) *10
[ 15.506909] ACPI: PCI Interrupt Link [LSI1] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
[ 15.507039] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 15.507069] pnp: PnP ACPI init
[ 15.507078] ACPI: bus type pnp registered
[ 15.509530] pnp: PnP ACPI: found 13 devices
[ 15.509533] ACPI: ACPI bus type pnp unregistered
[ 15.509767] PCI: Using ACPI for IRQ routing
[ 15.509771] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 15.512053] NET: Registered protocol family 8
[ 15.512056] NET: Registered protocol family 20
[ 15.512089] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
[ 15.512094] hpet0: 3 32-bit timers, 25000000 Hz
[ 15.512985] Time: hpet clocksource has been installed.
[ 15.512989] Clockevents: could not switch to one-shot mode: lapic is not functional.
[ 15.512992] Could not switch to high resolution mode on CPU 0
[ 15.514272] Clockevents: could not switch to one-shot mode: lapic is not functional.
[ 15.514279] Could not switch to high resolution mode on CPU 1
[ 15.514905] system 00:00: iomem range 0xffc00000-0xffffffff could not be reserved
[ 15.514909] system 00:00: iomem range 0xfec00000-0xfec00fff could not be reserved
[ 15.514913] system 00:00: iomem range 0xfee00000-0xfeefffff could not be reserved
[ 15.514916] system 00:00: iomem range 0xfed00000-0xfed00fff has been reserved
[ 15.514923] system 00:02: iomem range 0xe0000000-0xefffffff could not be reserved
[ 15.514930] system 00:03: ioport range 0x1000-0x107f has been reserved
[ 15.514933] system 00:03: ioport range 0x1080-0x10ff has been reserved
[ 15.514936] system 00:03: ioport range 0x1400-0x147f has been reserved
[ 15.514939] system 00:03: ioport range 0x1480-0x14ff has been reserved
[ 15.514941] system 00:03: ioport range 0x1800-0x187f has been reserved
[ 15.514944] system 00:03: ioport range 0x1880-0x18ff has been reserved
[ 15.514957] system 00:0b: ioport range 0x360-0x361 has been reserved
[ 15.514960] system 00:0b: ioport range 0x4d0-0x4d1 has been reserved
[ 15.529493] PCI: Bridge: 0000:00:02.0
[ 15.529496] IO window: 4000-4fff
[ 15.529499] MEM window: c0200000-c03fffff
[ 15.529502] PREFETCH window: c4200000-c43fffff
[ 15.529505] PCI: Bridge: 0000:00:03.0
[ 15.529506] IO window: disabled.
[ 15.529509] MEM window: disabled.
[ 15.529511] PREFETCH window: disabled.
[ 15.529516] PCI: Failed to allocate mem resource #6:20000@e0000000 for 0000:05:00.0
[ 15.529549] PCI: Bridge: 0000:00:04.0
[ 15.529552] IO window: 5000-5fff
[ 15.529555] MEM window: c1000000-c3ffffff
[ 15.529557] PREFETCH window: d0000000-dfffffff
[ 15.529560] PCI: Bridge: 0000:00:10.0
[ 15.529563] IO window: 6000-6fff
[ 15.529566] MEM window: c4000000-c40fffff
[ 15.529568] PREFETCH window: disabled.
[ 15.529581] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 15.529589] PCI: Setting latency timer of device 0000:00:03.0 to 64
[ 15.529596] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 15.529603] PCI: Setting latency timer of device 0000:00:10.0 to 64
[ 15.529636] NET: Registered protocol family 2
[ 15.533773] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 15.534100] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 15.534960] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[ 15.535530] TCP: Hash tables configured (established 131072 bind 65536)
[ 15.535534] TCP reno registered
[ 15.537127] checking if image is initramfs...<4>Clocksource tsc unstable (delta = -264619045 ns)
[ 16.992085] it is
[ 18.560687] Freeing initrd memory: 32044k freed
[ 18.560815] Simple Boot Flag at 0x36 set to 0x1
[ 18.562862] audit: initializing netlink socket (disabled)
[ 18.562876] audit(1202027557.744:1): initialized
[ 18.563054] highmem bounce pool size: 64 pages
[ 18.563138] VFS: Disk quotas dquot_6.5.1
[ 18.563164] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 18.563251] io scheduler noop registered
[ 18.563254] io scheduler anticipatory registered
[ 18.563256] io scheduler deadline registered
[ 18.563269] io scheduler cfq registered (default)
[ 18.663413] Boot video device is 0000:05:00.0
[ 18.663526] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 18.663543] assign_interrupt_mode Found MSI capability
[ 18.663545] Allocate Port Service[0000:00:02.0:pcie00]
[ 18.663582] Allocate Port Service[0000:00:02.0:pcie02]
[ 18.663615] Allocate Port Service[0000:00:02.0:pcie03]
[ 18.663668] PCI: Setting latency timer of device 0000:00:03.0 to 64
[ 18.663681] assign_interrupt_mode Found MSI capability
[ 18.663684] Allocate Port Service[0000:00:03.0:pcie00]
[ 18.663718] Allocate Port Service[0000:00:03.0:pcie02]
[ 18.663754] Allocate Port Service[0000:00:03.0:pcie03]
[ 18.663806] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 18.663819] assign_interrupt_mode Found MSI capability
[ 18.663822] Allocate Port Service[0000:00:04.0:pcie00]
[ 18.663861] Allocate Port Service[0000:00:04.0:pcie03]
[ 18.664302] ACPI: PCI Interrupt Link [LK1E] enabled at IRQ 23
[ 18.664310] ACPI: PCI Interrupt 0000:05:00.0[A] -> Link [LK1E] -> GSI 23 (level, low) -> IRQ 16
[ 18.664356] nvidiafb: Device ID: 10de0425
[ 18.664359] nvidiafb: unknown NV_ARCH
[ 18.669509] ACPI: Thermal Zone [THRM] (59 C)
[ 18.693617] Real Time Clock Driver v1.12ac
[ 18.693812] hpet_resources: 0xfed00000 is busy
[ 18.693853] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 18.695062] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 18.695222] fujitsu-laptop: driver 0.3 successfully loaded.
[ 18.695229] Loaded prism54 driver, version 1.2
[ 18.695331] input: Macintosh mouse button emulation as /class/input/input0
[ 18.695433] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
[ 18.696102] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 18.697293] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 18.697299] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 18.697302] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 18.697305] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 18.697307] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 18.699223] mice: PS/2 mouse device common for all mice
[ 18.699431] TCP cubic registered
[ 18.699442] NET: Registered protocol family 1
[ 18.699485] powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual-Core Processor TK-53 processors (2 cpu cores) (version 2.20.00)
[ 18.698132] powernow-k8: 0 : fid 0x9 (1700 MHz), vid 0x13
[ 18.698137] powernow-k8: 1 : fid 0x8 (1600 MHz), vid 0x14
[ 18.698139] powernow-k8: 2 : fid 0x0 (800 MHz), vid 0x1a
[ 18.699164] Using IPI No-Shortcut mode
[ 18.699346] Magic number: 12:522:522
[ 18.699704] Freeing unused kernel memory: 256k freed
[ 18.726317] input: AT Translated Set 2 keyboard as /class/input/input1
[ 21.102780] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 21.102786] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 21.103666] NFORCE-MCP51: IDE controller (0x10de:0x0265 rev 0xf1) at PCI slot 0000:00:0d.0
[ 21.103693] NFORCE-MCP51: not 100% native mode: will probe irqs later
[ 21.103699] NFORCE-MCP51: BIOS didn't set cable bits correctly. Enabling workaround.
[ 21.103704] NFORCE-MCP51: 0000:00:0d.0 (rev f1) UDMA133 controller
[ 21.103711] ide0: BM-DMA at 0x3080-0x3087, BIOS settings: hda:DMA, hdb:pio
[ 21.103722] ide1: BM-DMA at 0x3088-0x308f, BIOS settings: hdc:DMA, hdd:pio
[ 21.103731] Probing IDE interface ide0...
[ 21.125352] usbcore: registered new interface driver usbfs
[ 21.125383] usbcore: registered new interface driver hub
[ 21.125710] usbcore: registered new device driver usb
[ 21.132934] SCSI subsystem initialized
[ 21.136505] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 21.171938] libata version 3.00 loaded.
[ 21.428872] hdb: probing with STATUS(0x00) instead of ALTSTATUS(0xff)
[ 21.581842] hdb: probing with STATUS(0x00) instead of ALTSTATUS(0xff)
[ 21.887780] hda: probing with STATUS(0x50) instead of ALTSTATUS(0xff)
[ 22.040748] hda: probing with STATUS(0x51) instead of ALTSTATUS(0xff)
[ 22.295698] hda: probing with STATUS(0x51) instead of ALTSTATUS(0xff)
[ 22.397820] hda: Optiarc DVD RW AD-7540A, ATAPI CD/DVD-ROM drive
[ 22.397851] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 22.400143] hda: UDMA/33 mode selected
[ 22.403478] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 22.408148] Probing IDE interface ide1...
[ 22.945659] ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 22
[ 22.945672] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LUS0] -> GSI 22 (level, low) -> IRQ 17
[ 22.945686] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[ 22.945691] ohci_hcd 0000:00:0b.0: OHCI Host Controller
[ 22.945896] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1
[ 22.945922] ohci_hcd 0000:00:0b.0: irq 17, io mem 0xc0004000
[ 23.001363] usb usb1: configuration #1 chosen from 1 choice
[ 23.001388] hub 1-0:1.0: USB hub found
[ 23.001399] hub 1-0:1.0: 8 ports detected
[ 23.102005] ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 21
[ 23.102018] ACPI: PCI Interrupt 0000:00:0b.1[b] -> Link [LUS2] -> GSI 21 (level, low) -> IRQ 18
[ 23.102033] PCI: Setting latency timer of device 0000:00:0b.1 to 64
[ 23.102037] ehci_hcd 0000:00:0b.1: EHCI Host Controller
[ 23.102082] ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2
[ 23.102120] ehci_hcd 0000:00:0b.1: debug port 1
[ 23.102125] PCI: cache line size of 64 is not supported by device 0000:00:0b.1
[ 23.102137] ehci_hcd 0000:00:0b.1: irq 18, io mem 0xc0005000
[ 23.107531] ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 23.107638] usb usb2: configuration #1 chosen from 1 choice
[ 23.107662] hub 2-0:1.0: USB hub found
[ 23.107669] hub 2-0:1.0: 8 ports detected
[ 23.209104] ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 11
[ 23.209119] ACPI: PCI Interrupt 0000:07:06.0[A] -> Link [LNK1] -> GSI 11 (level, low) -> IRQ 11
[ 23.320456] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[c4000000-c40007ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 23.330486] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61.
[ 23.330819] ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 20
[ 23.330831] ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [LMAC] -> GSI 20 (level, low) -> IRQ 19
[ 23.330839] PCI: Setting latency timer of device 0000:00:14.0 to 64
[ 23.827807] usb 2-3: new high speed USB device using ehci_hcd and address 3
[ 23.844275] forcedeth 0000:00:14.0: ifname eth0, PHY OUI 0x5043 @ 1, addr 00:14:0b:3d:15:3b
[ 23.844279] forcedeth 0000:00:14.0: highdma pwrctl timirq gbit lnktim desc-v3
[ 23.846815] sata_nv 0000:00:0e.0: version 3.5
[ 23.846837] PCI: Enabling device 0000:00:0e.0 (0005 -> 0007)
[ 23.847141] ACPI: PCI Interrupt Link [LTID] enabled at IRQ 19
[ 23.847151] ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [LTID] -> GSI 19 (level, low) -> IRQ 20
[ 23.847202] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[ 23.854481] scsi0 : sata_nv
[ 23.854568] scsi1 : sata_nv
[ 23.854763] ata1: SATA max UDMA/133 cmd 0x30b0 ctl 0x30a4 bmdma 0x3090 irq 20
[ 23.854767] ata2: SATA max UDMA/133 cmd 0x30a8 ctl 0x30a0 bmdma 0x3098 irq 20
[ 23.946295] usb 2-3: configuration #1 chosen from 1 choice
[ 24.308318] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 24.431688] usb 1-1: new low speed USB device using ohci_hcd and address 2
[ 24.592747] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0040ca014e01c051]
[ 24.626828] usb 1-1: configuration #1 chosen from 1 choice
[ 24.659906] ata1.00: ATA-7: WDC WD1600BEVS-07RST0, 04.01G04, max UDMA/133
[ 24.659911] ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 24.664053] ata1.00: configured for UDMA/133
[ 24.901583] usb 1-7: new full speed USB device using ohci_hcd and address 3
[ 24.965160] ata2: SATA link down (SStatus 0 SControl 300)
[ 24.987161] scsi 0:0:0:0: Direct-Access ATA WDC WD1600BEVS-0 04.0 PQ: 0 ANSI: 5
[ 25.000959] Driver 'sd' needs updating - please use bus_type methods
[ 25.002387] hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
[ 25.002397] Uniform CD-ROM driver Revision: 3.20
[ 25.001060] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 25.001072] sd 0:0:0:0: [sda] Write Protect is off
[ 25.001075] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 25.001090] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 25.001164] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
[ 25.001172] sd 0:0:0:0: [sda] Write Protect is off
[ 25.001175] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 25.001188] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 25.001191] sda: sda1 sda2 < sda5 sda6 > sda3 sda4
[ 25.076716] sd 0:0:0:0: [sda] Attached SCSI disk
[ 25.080100] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 25.150163] usb 1-7: configuration #1 chosen from 1 choice
[ 25.151505] usbcore: registered new interface driver hiddev
[ 25.157455] input: PS/2+USB Mouse as /class/input/input2
[ 25.162252] input: USB HID v1.00 Mouse [PS/2+USB Mouse] on usb-0000:00:0b.0-1
[ 25.162276] usbcore: registered new interface driver usbhid
[ 25.162280] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 25.499723] kjournald starting. Commit interval 5 seconds
[ 25.501141] EXT3-fs: mounted filesystem with ordered data mode.
[ 32.061707] input: Power Button (FF) as /class/input/input3
[ 32.077150] ACPI: Power Button (FF) [PWRF]
[ 32.077231] input: Power Button (CM) as /class/input/input4
[ 32.088112] ACPI: Power Button (CM) [PWRB]
[ 32.088172] input: Sleep Button (CM) as /class/input/input5
[ 32.100112] ACPI: Sleep Button (CM) [SLPB]
[ 32.100208] input: Lid Switch as /class/input/input6
[ 32.104207] ACPI: Lid Switch [LID]
[ 32.293407] ACPI: AC Adapter [ACAD] (on-line)
[ 32.379172] NET: Registered protocol family 17
[ 32.452722] ACPI: Battery Slot [BAT0] (battery present)
[ 32.693737] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 32.792752] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 32.868461] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x3040
[ 32.868484] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x3000
[ 32.955479] input: PC Speaker as /class/input/input7
[ 33.310055] Bluetooth: Core ver 2.11
[ 33.310121] NET: Registered protocol family 31
[ 33.310124] Bluetooth: HCI device and connection manager initialized
[ 33.310129] Bluetooth: HCI socket layer initialized
[ 33.330299] input: PS/2 Mouse as /class/input/input8
[ 33.354061] input: AlpsPS/2 ALPS GlidePoint as /class/input/input9
[ 33.359346] Bluetooth: HCI USB driver ver 2.9
[ 33.361511] usbcore: registered new interface driver hci_usb
[ 33.606846] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 18
[ 33.606858] ACPI: PCI Interrupt 0000:00:10.1[b] -> Link [LAZA] -> GSI 18 (level, low) -> IRQ 21
[ 33.606883] PCI: Setting latency timer of device 0000:00:10.1 to 64
[ 33.659368] hda_codec: Unknown model for ALC882, trying auto-probe from BIOS...
[ 33.902471] loop: module loaded
[ 34.075527] Adding 3903752k swap on /dev/sda5. Priority:-1 extents:1 across:3903752k
[ 34.478448] EXT3 FS on sda6, internal journal
[ 35.680292] kjournald starting. Commit interval 5 seconds
[ 35.682292] EXT3 FS on sda1, internal journal
[ 35.682300] EXT3-fs: mounted filesystem with ordered data mode.
[ 35.734211] kjournald starting. Commit interval 5 seconds
[ 35.735960] EXT3 FS on sda4, internal journal
[ 35.735967] EXT3-fs: mounted filesystem with ordered data mode.
[ 35.804569] NTFS driver 2.1.29 [Flags: R/O MODULE].
[ 35.897803] NTFS volume version 3.1.
[ 36.360189] NET: Registered protocol family 10
[ 36.360430] lo: Disabled Privacy Extensions
[ 38.264476] No dock devices found.
[ 44.269657] eth0: no IPv6 routers present
[ 51.758578] Bluetooth: L2CAP ver 2.9
[ 51.758585] Bluetooth: L2CAP socket layer initialized
[ 51.818450] Bluetooth: RFCOMM socket layer initialized
[ 51.818464] Bluetooth: RFCOMM TTY layer initialized
[ 51.818466] Bluetooth: RFCOMM ver 1.8
[ 100.949547] UDF-fs: No VRS found
[ 101.008954] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 101.027744] ISO 9660 Extensions: RRIP_1991A

je vais essayer de refaire un kernel en enlevant moins d'options, c'est difficile de trouver quand on a des drivers génériques qui empêchent le fonctionnement du hardware

patko · Le 03/02/2008, à 10:01

RiFLE+ a écrit :

Bon désolé de faire mon monologue, mais mon controleur WiFi n'apparait pas dans le lspci, et l'installation est plutà´t pas facile avec ndiswrapper ! Quelqu'un aurait une idée ?

salut, un amis m'a indiqué qu'il fallait utiliser le driver windows (un .sys) pour faire foctionner le wifi avec ndsiwrapper, j'essaye de trouver pourquoi ma machine chauffe, et je regarde cette histoire de wifi., Pour virtualbox avec autre chose que windows, je n'ai pas encore essayé.

RiFLE+ · Le 03/02/2008, à 15:56

Mhh en fait j'ai regardé, VirtualBox n'utilise pas la carte WiFi. C'est à dire qu'il applique du NAT à la connexion réseau pour que celui de Windows soit effectif. La solution serait d'ajouter une connexion/carte WiFi mannuellement dans VirtualBox, mais c'est plus facile à dire qu'a faire

patko · Le 05/02/2008, à 09:10

RiFLE+ a écrit :

Mhh en fait j'ai regardé, VirtualBox n'utilise pas la carte WiFi. C'est à dire qu'il applique du NAT à la connexion réseau pour que celui de Windows soit effectif. La solution serait d'ajouter une connexion/carte WiFi mannuellement dans VirtualBox, mais c'est plus facile à dire qu'a faire

en fait je ne comprends pas trop comment ça se passe avec le wifi, j'ai chargé le pilote fournit par fujitsu avec ndiswrapper, mais le hardware ne semble repèré, mon lsusb ne donne rien du tout.

Par contre pour le son, avec le noyau 2.6.4 il suffit d'ajouter au fichier /etc/modprobe.d/alsa-base" la ligne:

options snd-hda-intel model=3stack-dig

ref: http://doc.ubuntu-fr.org/materiel/chipset_intel_hda_realtek

et redémarrer (attention, si les réglages du micro ne sont pas au minimum, ça on a un larsen lorsque le driver est activé, inserer un casque ou un micro pour éviter ce désagrément) j'ai utilisé alsamixer pour muter l'écoute de l'entrée micro

alsamixer

patko · Le 05/02/2008, à 17:20

Voici peut-être une solution sans avoir à recompiler pour aveoir le dvd qui fonctionne

dans /etc/initramfs-tools/modules

ajouter:

blacklist ide_generic

et refaire l'image initrd avec la commande
'update-initramfs -u /boot/k.initrd' (remplacer k.initrd par le nom de l'image)

ou pour le faire sur le noyau actif:

update-initramfs -u

pouvez-vous me dire si ça le fait?

Changedman · Le 06/02/2008, à 11:49

Je teste ceci ce soir sur une partition spéciale et te donne les résultats.

Ubuntu-fr

Navigation

Liens de recherche

Annonce

#1 Le 07/01/2008, à 02:52

Installation sur Amilo Xa 2528-P5311

#2 Le 07/01/2008, à 13:41

Re : Installation sur Amilo Xa 2528-P5311

#3 Le 07/01/2008, à 13:48

Re : Installation sur Amilo Xa 2528-P5311

#4 Le 09/01/2008, à 09:36

Re : Installation sur Amilo Xa 2528-P5311

#5 Le 09/01/2008, à 15:57

Re : Installation sur Amilo Xa 2528-P5311

#6 Le 09/01/2008, à 16:31

Re : Installation sur Amilo Xa 2528-P5311

#7 Le 29/01/2008, à 06:30

Re : Installation sur Amilo Xa 2528-P5311

#8 Le 29/01/2008, à 18:23

Re : Installation sur Amilo Xa 2528-P5311

#9 Le 29/01/2008, à 20:58

Re : Installation sur Amilo Xa 2528-P5311

#10 Le 29/01/2008, à 22:41

Re : Installation sur Amilo Xa 2528-P5311

#11 Le 30/01/2008, à 05:05

Re : Installation sur Amilo Xa 2528-P5311

#12 Le 30/01/2008, à 19:52

Re : Installation sur Amilo Xa 2528-P5311

#13 Le 30/01/2008, à 23:29

Re : Installation sur Amilo Xa 2528-P5311

#14 Le 01/02/2008, à 17:47

Re : Installation sur Amilo Xa 2528-P5311

#15 Le 01/02/2008, à 22:18

Re : Installation sur Amilo Xa 2528-P5311

#16 Le 02/02/2008, à 15:26

Re : Installation sur Amilo Xa 2528-P5311

#17 Le 02/02/2008, à 17:53

Re : Installation sur Amilo Xa 2528-P5311

#18 Le 02/02/2008, à 19:21

Re : Installation sur Amilo Xa 2528-P5311

#19 Le 02/02/2008, à 21:49

Re : Installation sur Amilo Xa 2528-P5311

#20 Le 03/02/2008, à 09:55

Re : Installation sur Amilo Xa 2528-P5311

#21 Le 03/02/2008, à 10:01

Re : Installation sur Amilo Xa 2528-P5311

#22 Le 03/02/2008, à 15:56

Re : Installation sur Amilo Xa 2528-P5311

#23 Le 05/02/2008, à 09:10

Re : Installation sur Amilo Xa 2528-P5311

#24 Le 05/02/2008, à 17:20

Re : Installation sur Amilo Xa 2528-P5311

#25 Le 06/02/2008, à 11:49

Re : Installation sur Amilo Xa 2528-P5311

Pied de page des forums