Clés USB non détectées [Résolu]

Mike Yavel · Le 26/09/2008, à 10:38

Bonjour,

Je viens de me rendre compte que mes clés USB sous Ubuntu 8.04 n'étaient pas détectées ( Elles l'étaient avec Ubuntu GG ). Je ne me souviens pas d'avoir essayé depuis que je suis passé à Ubuntu 8.04 ( je l'ai peut-être fait et que ça marchait à l'époque) mais une chose est sûre, ça marchait sous Ubuntu GG...

Pourriez-vous m'aider ?

D'avance, merci.

Dernière modification par Mike Yavel (Le 02/10/2008, à 16:02)

zedtux · Le 26/09/2008, à 10:49

Et quand une de tes clés est branché, que donne un lsusb dans un terminal ?

contremaitre · Le 26/09/2008, à 10:55

et un dmesg apres avoir branché ta clé aussi ?

Mike Yavel · Le 26/09/2008, à 11:51

Le lsusb donne:

michael@michael:~$ lsusb
Bus 005 Device 005: ID 046d:0992 Logitech, Inc.
Bus 005 Device 001: ID 0000:0000
Bus 004 Device 001: ID 0000:0000
Bus 003 Device 002: ID 0461:0100 Primax Electronics, Ltd
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 005: ID 045e:00e1 Microsoft Corp. Wireless Laser Mouse 6000 Reciever
Bus 001 Device 004: ID 03f0:0c17 Hewlett-Packard
Bus 001 Device 001: ID 0000:0000

et le dmesg donne:

[ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000
[ 0.000000] Real-Time Preemption Support (C) 2004-2007 Ingo Molnar
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 517105
[ 0.000000] Kernel command line: root=UUID=5ad0d9a3-15cf-47a4-a43e-9cbe484d91a9 ro quiet splash
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 1398.791 MHz processor.
[ 23.116610] Console: colour VGA+ 80x25
[ 23.116615] console [tty0] enabled
[ 23.117539] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 23.119131] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 23.317765] Memory: 2054640k/2097088k available (2225k kernel code, 41152k reserved, 1059k data, 368k init, 1179584k highmem)
[ 23.317778] virtual kernel memory layout:
[ 23.317779] fixmap : 0xfff4b000 - 0xfffff000 ( 720 kB)
[ 23.317781] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 23.317783] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 23.317785] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 23.317787] .init : 0xc043b000 - 0xc0497000 ( 368 kB)
[ 23.317788] .data : 0xc032c6f0 - 0xc0435324 (1059 kB)
[ 23.317790] .text : 0xc0100000 - 0xc032c6f0 (2225 kB)
[ 23.317795] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 23.377987] Calibrating delay using timer specific routine.. 2799.49 BogoMIPS (lpj=1399745)
[ 23.378055] Security Framework initialized
[ 23.378067] SELinux: Disabled at boot.
[ 23.378083] AppArmor: AppArmor initialized
[ 23.378089] Failure registering capabilities with primary security module.
[ 23.378113] Mount-cache hash table entries: 512
[ 23.378354] Initializing cgroup subsys ns
[ 23.378362] Initializing cgroup subsys cpuacct
[ 23.378379] CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000 00000000
[ 23.378392] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 23.378396] CPU: L2 Cache: 256K (64 bytes/line)
[ 23.378401] CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000420 00000000 00000000 00000000 00000000
[ 23.378419] Compat vDSO mapped to ffffe000.
[ 23.378440] Checking 'hlt' instruction... OK.
[ 23.382345] SMP alternatives: switching to UP code
[ 23.383723] Freeing SMP alternatives: 9k freed
[ 23.383934] Early unpacking initramfs... done
[ 23.865912] ACPI: Core revision 20070126
[ 23.866054] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 23.868502] CPU0: AMD Athlon(tm) XP 1600+ stepping 02
[ 23.868537] Total of 1 processors activated (2799.49 BogoMIPS).
[ 23.869306] ENABLING IO-APIC IRQs
[ 23.869639] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 23.981486] Brought up 1 CPUs
[ 23.981567] CPU0 attaching sched-domain:
[ 23.981572] domain 0: span 01
[ 23.981575] groups: 01
[ 23.981960] net_namespace: 76 bytes
[ 23.981970] Booting paravirtualized kernel on bare hardware
[ 23.982747] Time: 22:07:09 Date: 09/25/08
[ 23.982836] NET: Registered protocol family 16
[ 23.983216] EISA bus registered
[ 23.983256] ACPI: bus type pci registered
[ 23.986784] PCI: PCI BIOS revision 2.10 entry at 0xfda71, last bus=1
[ 23.986789] PCI: Using configuration type 1
[ 23.986806] Setting up standard PCI resources
[ 23.991971] ACPI: EC: Look up EC in DSDT
[ 23.997288] ACPI: Interpreter enabled
[ 23.997293] ACPI: (supports S0 S1 S4 S5)
[ 23.997313] ACPI: Using IOAPIC for interrupt routing
[ 24.003659] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 24.004605] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 24.021105] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 12 14 15)
[ 24.021233] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 12 14 15)
[ 24.021360] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 12 14 15)
[ 24.021481] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 *12 14 15)
[ 24.021600] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 24.021721] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 24.021890] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 24.022013] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 24.022166] ACPI: Power Resource [URP1] (off)
[ 24.022208] ACPI: Power Resource [URP2] (off)
[ 24.022252] ACPI: Power Resource [FDDP] (off)
[ 24.022292] ACPI: Power Resource [LPTP] (off)
[ 24.022374] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 24.022433] pnp: PnP ACPI init
[ 24.022449] ACPI: bus type pnp registered
[ 24.026130] pnp: PnP ACPI: found 11 devices
[ 24.026136] ACPI: ACPI bus type pnp unregistered
[ 24.026142] PnPBIOS: Disabled by ACPI PNP
[ 24.026595] PCI: Using ACPI for IRQ routing
[ 24.026601] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 24.037796] NET: Registered protocol family 8
[ 24.037800] NET: Registered protocol family 20
[ 24.037959] AppArmor: AppArmor Filesystem Enabled
[ 24.049858] system 00:05: ioport range 0x295-0x296 has been reserved
[ 24.049863] system 00:05: ioport range 0x3f0-0x3f1 has been reserved
[ 24.049867] system 00:05: ioport range 0x4d0-0x4d1 has been reserved
[ 24.049871] system 00:05: ioport range 0x400-0x40f has been reserved
[ 24.049875] system 00:05: ioport range 0x800-0x87f has been reserved
[ 24.049880] system 00:05: iomem range 0xfec00000-0xfec00fff could not be reserved
[ 24.049884] system 00:05: iomem range 0xfee00000-0xfee00fff could not be reserved
[ 24.080634] PCI: Bridge: 0000:00:01.0
[ 24.080638] IO window: disabled.
[ 24.080644] MEM window: dde00000-dfefffff
[ 24.080649] PREFETCH window: cdd00000-ddcfffff
[ 24.080669] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 24.080702] NET: Registered protocol family 2
[ 24.115896] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 24.116514] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 24.119015] TCP bind hash table entries: 65536 (order: 9, 2359296 bytes)
[ 24.123954] TCP: Hash tables configured (established 131072 bind 65536)
[ 24.123960] TCP reno registered
[ 24.136023] checking if image is initramfs... it is
[ 25.042826] Freeing initrd memory: 7297k freed
[ 25.044100] audit: initializing netlink socket (disabled)
[ 25.044125] audit(1222380429.625:1): initialized
[ 25.044351] krcupreemptd setsched 0
[ 25.044354] prio = 98
[ 25.044460] highmem bounce pool size: 64 pages
[ 25.044564] VFS: Disk quotas dquot_6.5.1
[ 25.044604] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 25.044736] io scheduler noop registered
[ 25.044739] io scheduler anticipatory registered
[ 25.044742] io scheduler deadline registered
[ 25.044754] io scheduler cfq registered (default)
[ 25.044771] PCI: VIA PCI bridge detected. Disabling DAC.
[ 25.044845] PCI: Bypassing VIA 8237 APIC De-Assert Message
[ 25.044868] Boot video device is 0000:01:00.0
[ 25.045399] isapnp: Scanning for PnP cards...
[ 25.402543] isapnp: No Plug & Play device found
[ 25.466342] Real Time Clock Driver v1.12ac
[ 25.466521] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 25.466686] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 25.467896] 00:02: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 25.469411] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 25.469531] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 25.469694] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 25.469699] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 25.469904] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 25.482134] mice: PS/2 mouse device common for all mice
[ 25.482350] EISA: Probing bus 0 at eisa.0
[ 25.482395] EISA: Detected 0 cards.
[ 25.482400] cpuidle: using governor ladder
[ 25.482544] NET: Registered protocol family 1
[ 25.482587] Using IPI No-Shortcut mode
[ 25.482675] registered taskstats version 1
[ 25.482821] Magic number: 8:297:149
[ 25.482931] hash matches device ttyp3
[ 25.483134] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 25.483138] EDD information not available.
[ 25.483727] Freeing unused kernel memory: 368k freed
[ 25.514025] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 26.893262] fuse init (API version 7.9)
[ 27.959594] SCSI subsystem initialized
[ 27.976707] ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 17 (level, low) -> IRQ 16
[ 27.976719] 3c59x: Donald Becker and others.
[ 27.976735] 0000:00:0d.0: 3Com PCI 3c900 Boomerang 10baseT at 0001d400.
[ 28.054741] usbcore: registered new interface driver usbfs
[ 28.054780] usbcore: registered new interface driver hub
[ 28.091238] usbcore: registered new device driver usb
[ 28.125229] USB Universal Host Controller Interface driver v3.0
[ 28.125365] ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 17
[ 28.125384] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 28.125812] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
[ 28.142552] libata version 3.00 loaded.
[ 28.155218] uhci_hcd 0000:00:10.0: irq 17, io base 0x0000c400
[ 28.155467] usb usb1: configuration #1 chosen from 1 choice
[ 28.155506] hub 1-0:1.0: USB hub found
[ 28.155521] hub 1-0:1.0: 2 ports detected
[ 28.212252] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
[ 28.220796] Floppy drive(s): fd0 is 1.44M
[ 28.242130] FDC 0 is a post-1991 82077
[ 28.256455] ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 17
[ 28.256477] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 28.256516] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
[ 28.256546] uhci_hcd 0000:00:10.1: irq 17, io base 0x0000c800
[ 28.256712] usb usb2: configuration #1 chosen from 1 choice
[ 28.256747] hub 2-0:1.0: USB hub found
[ 28.256764] hub 2-0:1.0: 2 ports detected
[ 28.357427] ACPI: PCI Interrupt 0000:00:10.2[b] -> GSI 21 (level, low) -> IRQ 17
[ 28.357449] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 28.357491] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
[ 28.357523] uhci_hcd 0000:00:10.2: irq 17, io base 0x0000cc00
[ 28.357692] usb usb3: configuration #1 chosen from 1 choice
[ 28.357728] hub 3-0:1.0: USB hub found
[ 28.357744] hub 3-0:1.0: 2 ports detected
[ 28.458457] ACPI: PCI Interrupt 0000:00:10.3[b] -> GSI 21 (level, low) -> IRQ 17
[ 28.458479] uhci_hcd 0000:00:10.3: UHCI Host Controller
[ 28.458518] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
[ 28.458550] uhci_hcd 0000:00:10.3: irq 17, io base 0x0000d000
[ 28.458719] usb usb4: configuration #1 chosen from 1 choice
[ 28.458755] hub 4-0:1.0: USB hub found
[ 28.458771] hub 4-0:1.0: 2 ports detected
[ 28.462261] usb 1-1: new full speed USB device using uhci_hcd and address 2
[ 28.559406] sata_via 0000:00:0f.0: version 2.3
[ 28.559452] ACPI: PCI Interrupt 0000:00:0f.0[b] -> GSI 20 (level, low) -> IRQ 18
[ 28.559535] sata_via 0000:00:0f.0: routed to hard irq line 10
[ 28.562646] scsi0 : sata_via
[ 28.564437] scsi1 : sata_via
[ 28.564538] ata1: SATA max UDMA/133 cmd 0xec00 ctl 0xe800 bmdma 0xdc00 irq 18
[ 28.564543] ata2: SATA max UDMA/133 cmd 0xe400 ctl 0xe000 bmdma 0xdc08 irq 18
[ 28.633348] usb 1-1: configuration #1 chosen from 1 choice
[ 28.765245] ata1: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
[ 28.841268] usb 1-2: new low speed USB device using uhci_hcd and address 3
[ 28.989263] ata2: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
[ 29.009177] usb 1-2: configuration #1 chosen from 1 choice
[ 29.010416] ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 18
[ 29.010517] ACPI: PCI interrupt for device 0000:00:0f.1 disabled
[ 29.011396] ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 17
[ 29.011418] ehci_hcd 0000:00:10.4: EHCI Host Controller
[ 29.011664] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
[ 29.011745] ehci_hcd 0000:00:10.4: irq 17, io mem 0xdfffbe00
[ 29.017261] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 29.017464] usb usb5: configuration #1 chosen from 1 choice
[ 29.017503] hub 5-0:1.0: USB hub found
[ 29.017521] hub 5-0:1.0: 8 ports detected
[ 29.120301] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 19
[ 29.120759] eth1: VIA Rhine II at 0xdfffbd00, 00:0b:6a:c3:a0:13, IRQ 19.
[ 29.122499] eth1: MII PHY found at address 1, status 0x786d advertising 05e1 Link 41e1.
[ 29.125943] pata_via 0000:00:0f.1: version 0.3.3
[ 29.125979] ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 18
[ 29.131782] scsi2 : pata_via
[ 29.133293] scsi3 : pata_via
[ 29.137047] ata3: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xfc00 irq 14
[ 29.137052] ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xfc08 irq 15
[ 29.219315] usb 1-1: USB disconnect, address 2
[ 29.293849] ata3.00: ATA-7: Maxtor 6Y080P0, YAR41BW0, max UDMA/133
[ 29.293857] ata3.00: 160086528 sectors, multi 16: LBA
[ 29.294066] ata3.01: ATA-7: HDT722525DLAT80, V44OA96A, max UDMA/133
[ 29.294070] ata3.01: 488397168 sectors, multi 16: LBA48
[ 29.299713] ata3.00: configured for UDMA/133
[ 29.305719] ata3.01: configured for UDMA/133
[ 29.323309] usb 1-2: USB disconnect, address 3
[ 29.796650] ata4.00: ATAPI: HL-DT-STDVD-ROM GDR8160B, 0009, max UDMA/66
[ 29.796682] ata4.01: ATAPI: HL-DT-ST DVDRAM GSA-4163B, A102, max UDMA/33
[ 29.796699] ata4.00: limited to UDMA/33 due to 40-wire cable
[ 29.969540] ata4.00: configured for UDMA/33
[ 30.142570] ata4.01: configured for UDMA/33
[ 30.142788] scsi 2:0:0:0: Direct-Access ATA Maxtor 6Y080P0 YAR4 PQ: 0 ANSI: 5
[ 30.143576] scsi 2:0:1:0: Direct-Access ATA HDT722525DLAT80 V44O PQ: 0 ANSI: 5
[ 30.158843] scsi 3:0:0:0: CD-ROM HL-DT-ST DVD-ROM GDR8160B 0009 PQ: 0 ANSI: 5
[ 30.162704] scsi 3:0:1:0: CD-ROM HL-DT-ST DVDRAM GSA-4163B A102 PQ: 0 ANSI: 5
[ 30.189462] Driver 'sd' needs updating - please use bus_type methods
[ 30.189616] sd 2:0:0:0: [sda] 160086528 512-byte hardware sectors (81964 MB)
[ 30.189641] sd 2:0:0:0: [sda] Write Protect is off
[ 30.189646] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 30.189675] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.189755] sd 2:0:0:0: [sda] 160086528 512-byte hardware sectors (81964 MB)
[ 30.189772] sd 2:0:0:0: [sda] Write Protect is off
[ 30.189776] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 30.189802] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.189809] sda: sda1
[ 30.197811] sd 2:0:0:0: [sda] Attached SCSI disk
[ 30.197925] sd 2:0:1:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
[ 30.197949] sd 2:0:1:0: [sdb] Write Protect is off
[ 30.197953] sd 2:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 30.197982] sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.198056] sd 2:0:1:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
[ 30.198073] sd 2:0:1:0: [sdb] Write Protect is off
[ 30.198077] sd 2:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 30.198103] sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.198108] sdb: sdb1 sdb2 sdb3 sdb4
[ 30.208032] Driver 'sr' needs updating - please use bus_type methods
[ 30.215844] sd 2:0:1:0: [sdb] Attached SCSI disk
[ 30.236033] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 30.236066] sd 2:0:1:0: Attached scsi generic sg1 type 0
[ 30.236094] sr 3:0:0:0: Attached scsi generic sg2 type 5
[ 30.236296] scsi 3:0:1:0: Attached scsi generic sg3 type 5
[ 30.243939] sr0: scsi3-mmc drive: 20x/48x cd/rw xa/form2 cdda tray
[ 30.243950] Uniform CD-ROM driver Revision: 3.20
[ 30.244043] sr 3:0:0:0: Attached scsi CD-ROM sr0
[ 30.262681] sr1: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
[ 30.262812] sr 3:0:1:0: Attached scsi CD-ROM sr1
[ 30.565386] usb 5-4: new high speed USB device using ehci_hcd and address 5
[ 30.796651] usb 5-4: configuration #1 chosen from 1 choice
[ 30.952436] usbcore: registered new interface driver hiddev
[ 31.158379] usb 1-1: new full speed USB device using uhci_hcd and address 4
[ 31.333283] usb 1-1: configuration #1 chosen from 1 choice
[ 31.541405] usb 1-2: new low speed USB device using uhci_hcd and address 5
[ 31.709156] usb 1-2: configuration #1 chosen from 1 choice
[ 31.917432] usb 2-1: new low speed USB device using uhci_hcd and address 2
[ 32.030437] usb 2-1: device descriptor read/64, error -71
[ 32.244451] usb 2-1: device descriptor read/64, error -71
[ 32.447467] usb 2-1: new low speed USB device using uhci_hcd and address 3
[ 32.560473] usb 2-1: device descriptor read/64, error -71
[ 32.774489] usb 2-1: device descriptor read/64, error -71
[ 32.977504] usb 2-1: new low speed USB device using uhci_hcd and address 4
[ 33.385529] usb 2-1: device not accepting address 4, error -71
[ 33.487539] usb 2-1: new low speed USB device using uhci_hcd and address 5
[ 33.895566] usb 2-1: device not accepting address 5, error -71
[ 34.101581] usb 3-1: new low speed USB device using uhci_hcd and address 2
[ 34.267340] usb 3-1: configuration #1 chosen from 1 choice
[ 34.321788] input: Microsoft Microsoft Wireless Optical Mouse� 1.00 as /devices/pci0000:00/0000:00:10.0/usb1/1-2/1-2:1.0/input/input2
[ 34.333669] input,hidraw0: USB HID v1.11 Mouse [Microsoft Microsoft Wireless Optical Mouse� 1.00] on usb-0000:00:10.0-2
[ 34.346519] input: Primx Orbit Elite Wireless Trackball as /devices/pci0000:00/0000:00:10.2/usb3/3-1/3-1:1.0/input/input3
[ 34.357673] input,hidraw1: USB HID v1.00 Mouse [Primx Orbit Elite Wireless Trackball ] on usb-0000:00:10.2-1
[ 34.357703] usbcore: registered new interface driver usbhid
[ 34.357710] /build/buildd/linux-2.6.24/debian/build/custom-source-rt/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 34.522844] Attempting manual resume
[ 34.522851] swsusp: Resume From Partition 8:18
[ 34.522853] PM: Checking swsusp image.
[ 34.523122] PM: Resume from disk failed.
[ 34.568936] EXT3-fs: mounted filesystem with ordered data mode.
[ 34.569063] kjournald starting. Commit interval 5 seconds
[ 42.908815] Linux agpgart interface v0.102
[ 43.014443] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 43.062416] agpgart: Detected VIA KT400/KT400A/KT600 chipset
[ 43.067728] agpgart: AGP aperture is 64M @ 0xe0000000
[ 43.125448] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 44.090596] input: Power Button (FF) as /devices/virtual/input/input4
[ 44.099300] ACPI: Power Button (FF) [PWRF]
[ 44.099537] input: Power Button (CM) as /devices/virtual/input/input5
[ 44.113308] ACPI: Power Button (CM) [PWRB]
[ 44.113561] input: Sleep Button (CM) as /devices/virtual/input/input6
[ 44.125309] ACPI: Sleep Button (CM) [SLPB]
[ 46.330889] nvidia: module license 'NVIDIA' taints kernel.
[ 47.504812] input: PC Speaker as /devices/platform/pcspkr/input/input7
[ 47.923265] usblp0: USB Bidirectional printer dev 4 if 0 alt 1 proto 2 vid 0x03F0 pid 0x0C17
[ 47.923299] usbcore: registered new interface driver usblp
[ 48.068863] parport_pc 00:03: reported by Plug and Play ACPI
[ 48.068962] parport0: PC-style at 0x378 (0x778), irq 7, dma 0 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[ 48.133972] ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 20
[ 48.166731] PCI: Setting latency timer of device 0000:00:11.5 to 64
[ 48.309637] Linux video capture interface: v2.00
[ 48.425872] uvcvideo: Found UVC 1.00 device <unnamed> (046d:0992)
[ 48.438956] usbcore: registered new interface driver uvcvideo
[ 48.438966] USB Video Class driver (v0.1.0)
[ 48.534028] usbcore: registered new interface driver snd-usb-audio
[ 49.010792] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 21
[ 49.011458] NVRM: loading NVIDIA Linux x86 Kernel Module 96.43.05 Tue Jan 22 19:36:58 PST 2008
[ 52.405084] lp0: using parport0 (interrupt-driven).
[ 52.503332] Adding 1951888k swap on /dev/sdb2. Priority:-1 extents:1 across:1951888k
[ 53.106677] EXT3 FS on sdb1, internal journal
[ 58.655778] kjournald starting. Commit interval 5 seconds
[ 58.656144] EXT3 FS on sdb3, internal journal
[ 58.656153] EXT3-fs: mounted filesystem with ordered data mode.
[ 59.612846] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 60.293730] No dock devices found.
[ 61.911139] apm: BIOS not found.
[ 62.034908] ppdev: user-space parallel port driver
[ 62.179778] NET: Registered protocol family 10
[ 62.180611] lo: Disabled Privacy Extensions
[ 62.350903] audit(1222373268.112:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=5075 profile="/usr/sbin/cupsd" namespace="default"
[ 65.542504] eth1: link up, 100Mbps, full-duplex, lpa 0x41E1
[ 65.576294] eth0: setting half-duplex.
[ 65.688735] Bluetooth: Core ver 2.11
[ 65.690939] NET: Registered protocol family 31
[ 65.690949] Bluetooth: HCI device and connection manager initialized
[ 65.690957] Bluetooth: HCI socket layer initialized
[ 65.722898] Bluetooth: L2CAP ver 2.9
[ 65.722909] Bluetooth: L2CAP socket layer initialized
[ 65.801832] Bluetooth: RFCOMM socket layer initialized
[ 65.802285] Bluetooth: RFCOMM TTY layer initialized
[ 65.802577] Bluetooth: RFCOMM ver 1.8
[ 65.817829] usb 2-1: new low speed USB device using uhci_hcd and address 6
[ 65.931834] usb 2-1: device descriptor read/64, error -71
[ 66.145816] usb 2-1: device descriptor read/64, error -71
[ 66.348823] usb 2-1: new low speed USB device using uhci_hcd and address 7
[ 66.461871] usb 2-1: device descriptor read/64, error -71
[ 66.675912] usb 2-1: device descriptor read/64, error -71
[ 66.878862] usb 2-1: new low speed USB device using uhci_hcd and address 8
[ 67.286896] usb 2-1: device not accepting address 8, error -71
[ 67.388919] usb 2-1: new low speed USB device using uhci_hcd and address 9
[ 67.796938] usb 2-1: device not accepting address 9, error -71
[ 68.045246] NET: Registered protocol family 17
[ 68.498062] agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
[ 68.498090] agpgart: Device is in legacy mode, falling back to 2.x
[ 68.498097] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
[ 68.498157] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
[ 82.686962] eth1: no IPv6 routers present
[ 5545.811901] usb 2-1: new low speed USB device using uhci_hcd and address 10
[ 5545.925906] usb 2-1: device descriptor read/64, error -71
[ 5546.139925] usb 2-1: device descriptor read/64, error -71
[ 5546.342941] usb 2-1: new low speed USB device using uhci_hcd and address 11
[ 5546.455944] usb 2-1: device descriptor read/64, error -71
[ 5546.669961] usb 2-1: device descriptor read/64, error -71
[ 5546.872973] usb 2-1: new low speed USB device using uhci_hcd and address 12
[ 5547.280991] usb 2-1: device not accepting address 12, error -71
[ 5547.383020] usb 2-1: new low speed USB device using uhci_hcd and address 13
[ 5547.791025] usb 2-1: device not accepting address 13, error -71
[ 5547.796784] usblp0: removed
[ 8081.960284] usb 2-1: new low speed USB device using uhci_hcd and address 14
[ 8082.074298] usb 2-1: device descriptor read/64, error -71
[ 8082.288332] usb 2-1: device descriptor read/64, error -71
[ 8082.491323] usb 2-1: new low speed USB device using uhci_hcd and address 15
[ 8082.604845] usb 2-1: device descriptor read/64, error -71
[ 8082.646508] audit(1222381343.994:3): type=1503 operation="inode_permission" requested_mask="::rw" denied_mask="::rw" name="/dev/tty" pid=6486 profile="/usr/sbin/cupsd" namespace="default"
[ 8082.818362] usb 2-1: device descriptor read/64, error -71
[ 8083.021348] usb 2-1: new low speed USB device using uhci_hcd and address 16
[ 8083.429385] usb 2-1: device not accepting address 16, error -71
[ 8083.531383] usb 2-1: new low speed USB device using uhci_hcd and address 17
[ 8083.939413] usb 2-1: device not accepting address 17, error -71
[27803.004514] eth1: link down
[27805.371561] eth1: link up, 100Mbps, full-duplex, lpa 0x41E1
[27805.372689] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[27816.306332] eth1: no IPv6 routers present
[27837.313092] eth1: no IPv6 routers present
[41591.943645] usb 2-1: new low speed USB device using uhci_hcd and address 18
[41592.057655] usb 2-1: device descriptor read/64, error -71
[41592.271664] usb 2-1: device descriptor read/64, error -71
[41592.474711] usb 2-1: new low speed USB device using uhci_hcd and address 19
[41592.587708] usb 2-1: device descriptor read/64, error -71
[41592.801709] usb 2-1: device descriptor read/64, error -71
[41593.004716] usb 2-1: new low speed USB device using uhci_hcd and address 20
[41593.412737] usb 2-1: device not accepting address 20, error -71
[41593.514774] usb 2-1: new low speed USB device using uhci_hcd and address 21
[41593.922773] usb 2-1: device not accepting address 21, error -71
[44656.621776] usb 5-7: new high speed USB device using ehci_hcd and address 7
[44695.468481] usb 5-7: new high speed USB device using ehci_hcd and address 9
[44695.596670] usb 5-7: configuration #1 chosen from 1 choice
[44695.763197] usbcore: registered new interface driver libusual
[44695.804447] Initializing USB Mass Storage driver...
[44695.816512] scsi4 : SCSI emulation for USB Mass Storage devices
[44695.821964] usbcore: registered new interface driver usb-storage
[44695.821980] USB Mass Storage support registered.
[44695.822869] usb-storage: device found at 9
[44695.823073] usb-storage: waiting for device to settle before scanning
[44696.535923] usb 5-7: USB disconnect, address 9
[44696.768569] usb 5-7: new high speed USB device using ehci_hcd and address 10
[44697.273586] usb 5-7: device not accepting address 10, error -71
[44697.533618] usb 5-7: new high speed USB device using ehci_hcd and address 12
[44698.110660] usb 5-7: new high speed USB device using ehci_hcd and address 15
[44698.529686] usb 5-7: new high speed USB device using ehci_hcd and address 17
[44724.912552] usb 5-7: new high speed USB device using ehci_hcd and address 18
[44756.748739] usb 5-7: new high speed USB device using ehci_hcd and address 19
[47684.169318] usb 5-7: new high speed USB device using ehci_hcd and address 20
[49265.615291] usb 2-1: new low speed USB device using uhci_hcd and address 22
[49265.728304] usb 2-1: device descriptor read/64, error -71
[49265.942312] usb 2-1: device descriptor read/64, error -71
[49266.145329] usb 2-1: new low speed USB device using uhci_hcd and address 23
[49266.258340] usb 2-1: device descriptor read/64, error -71
[49266.472353] usb 2-1: device descriptor read/64, error -71
[49266.675370] usb 2-1: new low speed USB device using uhci_hcd and address 24
[49267.083385] usb 2-1: device not accepting address 24, error -71
[49267.185427] usb 2-1: new low speed USB device using uhci_hcd and address 25
[49267.593437] usb 2-1: device not accepting address 25, error -71
michael@michael:~$

Mike Yavel · Le 28/09/2008, à 11:13

Alors ? c'est grave docteur ?

zedtux · Le 29/09/2008, à 07:31

Ben apparemment tout vient de l'erreur usb 2-1: device descriptor read/64, error -71.

J'avais commencé quelques recherches sur ce message... mais pour le moment rien trouvé.

Quel est la marque, le model, de ta clé ?

Mike Yavel · Le 29/09/2008, à 10:32

ça le fait avec mes 3 clés ( de marques différentes )

zedtux · Le 29/09/2008, à 13:06

Mmm... Étrange !

Et tes clés fonctionnaient avant et suite à une mise à jour ca ne fonctionne plus, ou dès le départ elles ne fonctionnaient pas ?

contremaitre · Le 29/09/2008, à 15:22

il y aurait un bug usb dans ubuntu qui pourrait te causer ce soucis.
Pour essayer de le corriger il faut modifier un fichier, qu'on va sauvegarder avant, au cas ou.
Donc pour sauvegarder le fichier dans son répertoire home :

sudo cp /sys/module/usbcore/parameters/autosuspend ~/autosuspend_bak

Ensuite tu modifie ce fichier en faisant :

sudo echo -1 >/sys/module/usbcore/parameters/autosuspend

Puis tu redemarre et tu regardes si ta cle fonctionne.

Si tu veux remettre en place le fichier tel qu'il était tu fait :

sudo cp ~/autosuspend_bak /sys/module/usbcore/parameters/autosuspend

Dernière modification par contremaitre (Le 29/09/2008, à 16:46)

Mike Yavel · Le 29/09/2008, à 16:24

J'ai un problème dès la première ligne de code ( celle qui sert à sauvegarder le fichier à modifier):

cp: ne peut créer le fichier régulier `/sys/module/usbcore/parameters/autosuspend_bak': Aucun fichier ou dossier de ce type

contremaitre · Le 29/09/2008, à 16:47

Désolé j'aurai du essayer la comande. J'ai modifié mon message pour qu'elle fonctionne correctement en sauvegardant le fichier dans le répertoire utilsateur a la place du repertoire d'origine.

Mike Yavel · Le 29/09/2008, à 17:22

ça a marché...lorsque j'ai introduit la première clé...J'ai ensuite démonté le volume pour essayer avec les suivantes mais ça n'a pas fonctionné. Je suis alors revenu à la première pour voir si elle était encore reconnue mais là encore, j'ai fait chou blanc... ( je précise que toutes les clés sont reconnues sous Windows. Elles fonctionnent donc correctement)

contremaitre · Le 29/09/2008, à 17:48

désolé je sais pas trop.
Essaye de faire des dmesg après avoir branché tes clés, tu verra ce que le systeme essaye de faire et là ou il echoue dans les derniers messages de dmesg.

Tu peux ensuite chercher ces erreurs sous google, ou les poster ici.

Mike Yavel · Le 29/09/2008, à 19:25

16
[ 27.994922] 3c59x: Donald Becker and others.
[ 27.994939] 0000:00:0d.0: 3Com PCI 3c900 Boomerang 10baseT at 0001d400.
[ 28.078062] usbcore: registered new interface driver usbfs
[ 28.078102] usbcore: registered new interface driver hub
[ 28.112833] usbcore: registered new device driver usb
[ 28.148813] USB Universal Host Controller Interface driver v3.0
[ 28.148955] ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 17
[ 28.148973] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 28.149400] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
[ 28.167340] libata version 3.00 loaded.
[ 28.181830] uhci_hcd 0000:00:10.0: irq 17, io base 0x0000c400
[ 28.182083] usb usb1: configuration #1 chosen from 1 choice
[ 28.182123] hub 1-0:1.0: USB hub found
[ 28.182138] hub 1-0:1.0: 2 ports detected
[ 28.242831] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
[ 28.250989] Floppy drive(s): fd0 is 1.44M
[ 28.271713] FDC 0 is a post-1991 82077
[ 28.283067] ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 17
[ 28.283089] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 28.283128] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
[ 28.283159] uhci_hcd 0000:00:10.1: irq 17, io base 0x0000c800
[ 28.283330] usb usb2: configuration #1 chosen from 1 choice
[ 28.283366] hub 2-0:1.0: USB hub found
[ 28.283383] hub 2-0:1.0: 2 ports detected
[ 28.384038] ACPI: PCI Interrupt 0000:00:10.2[b] -> GSI 21 (level, low) -> IRQ 17
[ 28.384060] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 28.384104] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
[ 28.384135] uhci_hcd 0000:00:10.2: irq 17, io base 0x0000cc00
[ 28.384306] usb usb3: configuration #1 chosen from 1 choice
[ 28.384344] hub 3-0:1.0: USB hub found
[ 28.384360] hub 3-0:1.0: 2 ports detected
[ 28.485039] ACPI: PCI Interrupt 0000:00:10.3[b] -> GSI 21 (level, low) -> IRQ 17
[ 28.485061] uhci_hcd 0000:00:10.3: UHCI Host Controller
[ 28.485100] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
[ 28.485131] uhci_hcd 0000:00:10.3: irq 17, io base 0x0000d000
[ 28.485308] usb usb4: configuration #1 chosen from 1 choice
[ 28.485345] hub 4-0:1.0: USB hub found
[ 28.485361] hub 4-0:1.0: 2 ports detected
[ 28.488845] usb 1-1: new full speed USB device using uhci_hcd and address 2
[ 28.586037] sata_via 0000:00:0f.0: version 2.3
[ 28.586084] ACPI: PCI Interrupt 0000:00:0f.0[b] -> GSI 20 (level, low) -> IRQ 18
[ 28.586170] sata_via 0000:00:0f.0: routed to hard irq line 10
[ 28.590478] scsi0 : sata_via
[ 28.592264] scsi1 : sata_via
[ 28.592362] ata1: SATA max UDMA/133 cmd 0xec00 ctl 0xe800 bmdma 0xdc00 irq 18
[ 28.592367] ata2: SATA max UDMA/133 cmd 0xe400 ctl 0xe000 bmdma 0xdc08 irq 18
[ 28.660958] usb 1-1: configuration #1 chosen from 1 choice
[ 28.792849] ata1: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
[ 28.868861] usb 1-2: new low speed USB device using uhci_hcd and address 3
[ 29.016863] ata2: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
[ 29.036789] usb 1-2: configuration #1 chosen from 1 choice
[ 29.038017] ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 18
[ 29.038118] ACPI: PCI interrupt for device 0000:00:0f.1 disabled
[ 29.038991] ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 17
[ 29.039013] ehci_hcd 0000:00:10.4: EHCI Host Controller
[ 29.039208] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
[ 29.039351] ehci_hcd 0000:00:10.4: irq 17, io mem 0xdfffbe00
[ 29.044864] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 29.045068] usb usb5: configuration #1 chosen from 1 choice
[ 29.045109] hub 5-0:1.0: USB hub found
[ 29.045127] hub 5-0:1.0: 8 ports detected
[ 29.147899] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 19
[ 29.148361] eth1: VIA Rhine II at 0xdfffbd00, 00:0b:6a:c3:a0:13, IRQ 19.
[ 29.150099] eth1: MII PHY found at address 1, status 0x786d advertising 05e1 Link 41e1.
[ 29.153423] pata_via 0000:00:0f.1: version 0.3.3
[ 29.153459] ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 18
[ 29.159127] scsi2 : pata_via
[ 29.162156] scsi3 : pata_via
[ 29.164627] ata3: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xfc00 irq 14
[ 29.164632] ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xfc08 irq 15
[ 29.246905] usb 1-1: USB disconnect, address 2
[ 29.322436] ata3.00: ATA-7: Maxtor 6Y080P0, YAR41BW0, max UDMA/133
[ 29.322444] ata3.00: 160086528 sectors, multi 16: LBA
[ 29.322648] ata3.01: ATA-7: HDT722525DLAT80, V44OA96A, max UDMA/133
[ 29.322652] ata3.01: 488397168 sectors, multi 16: LBA48
[ 29.328304] ata3.00: configured for UDMA/133
[ 29.334340] ata3.01: configured for UDMA/133
[ 29.350909] usb 1-2: USB disconnect, address 3
[ 29.809247] ata4.00: ATAPI: HL-DT-STDVD-ROM GDR8160B, 0009, max UDMA/66
[ 29.809280] ata4.01: ATAPI: HL-DT-ST DVDRAM GSA-4163B, A102, max UDMA/33
[ 29.809297] ata4.00: limited to UDMA/33 due to 40-wire cable
[ 29.966140] ata4.00: configured for UDMA/33
[ 30.139150] ata4.01: configured for UDMA/33
[ 30.139363] scsi 2:0:0:0: Direct-Access ATA Maxtor 6Y080P0 YAR4 PQ: 0 ANSI: 5
[ 30.140157] scsi 2:0:1:0: Direct-Access ATA HDT722525DLAT80 V44O PQ: 0 ANSI: 5
[ 30.142505] scsi 3:0:0:0: CD-ROM HL-DT-ST DVD-ROM GDR8160B 0009 PQ: 0 ANSI: 5
[ 30.146376] scsi 3:0:1:0: CD-ROM HL-DT-ST DVDRAM GSA-4163B A102 PQ: 0 ANSI: 5
[ 30.175069] Driver 'sd' needs updating - please use bus_type methods
[ 30.175222] sd 2:0:0:0: [sda] 160086528 512-byte hardware sectors (81964 MB)
[ 30.175246] sd 2:0:0:0: [sda] Write Protect is off
[ 30.175251] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 30.175280] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.175360] sd 2:0:0:0: [sda] 160086528 512-byte hardware sectors (81964 MB)
[ 30.175377] sd 2:0:0:0: [sda] Write Protect is off
[ 30.175381] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 30.175407] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.175414] sda: sda1
[ 30.178330] sd 2:0:0:0: [sda] Attached SCSI disk
[ 30.178443] sd 2:0:1:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
[ 30.178466] sd 2:0:1:0: [sdb] Write Protect is off
[ 30.178471] sd 2:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 30.178499] sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.178571] sd 2:0:1:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
[ 30.178588] sd 2:0:1:0: [sdb] Write Protect is off
[ 30.178591] sd 2:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 30.178618] sd 2:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 30.178623] sdb: sdb1 sdb2 sdb3 sdb4
[ 30.194462] Driver 'sr' needs updating - please use bus_type methods
[ 30.198686] sd 2:0:1:0: [sdb] Attached SCSI disk
[ 30.215295] sr0: scsi3-mmc drive: 20x/48x cd/rw xa/form2 cdda tray
[ 30.215306] Uniform CD-ROM driver Revision: 3.20
[ 30.215395] sr 3:0:0:0: Attached scsi CD-ROM sr0
[ 30.216245] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 30.216277] sd 2:0:1:0: Attached scsi generic sg1 type 0
[ 30.216303] sr 3:0:0:0: Attached scsi generic sg2 type 5
[ 30.216332] sr 3:0:1:0: Attached scsi generic sg3 type 5
[ 30.234120] sr1: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
[ 30.234227] sr 3:0:1:0: Attached scsi CD-ROM sr1
[ 30.593962] usb 5-4: new high speed USB device using ehci_hcd and address 5
[ 30.826381] usb 5-4: configuration #1 chosen from 1 choice
[ 30.982036] usbcore: registered new interface driver hiddev
[ 31.187977] usb 1-1: new full speed USB device using uhci_hcd and address 4
[ 31.362899] usb 1-1: configuration #1 chosen from 1 choice
[ 31.571004] usb 1-2: new low speed USB device using uhci_hcd and address 5
[ 31.738772] usb 1-2: configuration #1 chosen from 1 choice
[ 31.947029] usb 2-1: new low speed USB device using uhci_hcd and address 2
[ 32.060034] usb 2-1: device descriptor read/64, error -71
[ 32.274049] usb 2-1: device descriptor read/64, error -71
[ 32.477064] usb 2-1: new low speed USB device using uhci_hcd and address 3
[ 32.590071] usb 2-1: device descriptor read/64, error -71
[ 32.804086] usb 2-1: device descriptor read/64, error -71
[ 33.007100] usb 2-1: new low speed USB device using uhci_hcd and address 4
[ 33.415126] usb 2-1: device not accepting address 4, error -71
[ 33.517135] usb 2-1: new low speed USB device using uhci_hcd and address 5
[ 33.925162] usb 2-1: device not accepting address 5, error -71
[ 34.131179] usb 3-1: new low speed USB device using uhci_hcd and address 2
[ 34.296942] usb 3-1: configuration #1 chosen from 1 choice
[ 34.351401] input: Microsoft Microsoft Wireless Optical Mouse� 1.00 as /devices/pci0000:00/0000:00:10.0/usb1/1-2/1-2:1.0/input/input2
[ 34.363290] input,hidraw0: USB HID v1.11 Mouse [Microsoft Microsoft Wireless Optical Mouse� 1.00] on usb-0000:00:10.0-2
[ 34.376116] input: Primx Orbit Elite Wireless Trackball as /devices/pci0000:00/0000:00:10.2/usb3/3-1/3-1:1.0/input/input3
[ 34.387275] input,hidraw1: USB HID v1.00 Mouse [Primx Orbit Elite Wireless Trackball ] on usb-0000:00:10.2-1
[ 34.387307] usbcore: registered new interface driver usbhid
[ 34.387314] /build/buildd/linux-2.6.24/debian/build/custom-source-rt/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 34.553898] Attempting manual resume
[ 34.553904] swsusp: Resume From Partition 8:18
[ 34.553907] PM: Checking swsusp image.
[ 34.554174] PM: Resume from disk failed.
[ 34.602525] EXT3-fs: mounted filesystem with ordered data mode.
[ 34.602656] kjournald starting. Commit interval 5 seconds
[ 42.930858] Linux agpgart interface v0.102
[ 43.009636] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 43.062027] agpgart: Detected VIA KT400/KT400A/KT600 chipset
[ 43.068130] agpgart: AGP aperture is 64M @ 0xe0000000
[ 43.127048] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 44.102972] input: Power Button (FF) as /devices/virtual/input/input4
[ 44.113898] ACPI: Power Button (FF) [PWRF]
[ 44.114132] input: Power Button (CM) as /devices/virtual/input/input5
[ 44.125901] ACPI: Power Button (CM) [PWRB]
[ 44.126156] input: Sleep Button (CM) as /devices/virtual/input/input6
[ 44.137907] ACPI: Sleep Button (CM) [SLPB]
[ 46.437929] nvidia: module license 'NVIDIA' taints kernel.
[ 46.865151] usblp0: USB Bidirectional printer dev 4 if 0 alt 1 proto 2 vid 0x03F0 pid 0x0C17
[ 46.865184] usbcore: registered new interface driver usblp
[ 47.736426] input: PC Speaker as /devices/platform/pcspkr/input/input7
[ 48.062229] Linux video capture interface: v2.00
[ 48.361413] uvcvideo: Found UVC 1.00 device <unnamed> (046d:0992)
[ 48.374281] usbcore: registered new interface driver uvcvideo
[ 48.374291] USB Video Class driver (v0.1.0)
[ 48.517028] usbcore: registered new interface driver snd-usb-audio
[ 48.634437] ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 20
[ 48.673368] PCI: Setting latency timer of device 0000:00:11.5 to 64
[ 48.958280] parport_pc 00:03: reported by Plug and Play ACPI
[ 48.958380] parport0: PC-style at 0x378 (0x778), irq 7, dma 0 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[ 49.186895] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 21
[ 49.187614] NVRM: loading NVIDIA Linux x86 Kernel Module 96.43.05 Tue Jan 22 19:36:58 PST 2008
[ 52.421094] lp0: using parport0 (interrupt-driven).
[ 52.519151] Adding 1951888k swap on /dev/sdb2. Priority:-1 extents:1 across:1951888k
[ 53.122931] EXT3 FS on sdb1, internal journal
[ 58.738364] kjournald starting. Commit interval 5 seconds
[ 58.738732] EXT3 FS on sdb3, internal journal
[ 58.738741] EXT3-fs: mounted filesystem with ordered data mode.
[ 59.678783] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 60.368656] No dock devices found.
[ 63.350008] apm: BIOS not found.
[ 63.623427] ppdev: user-space parallel port driver
[ 63.768056] NET: Registered protocol family 10
[ 63.768868] lo: Disabled Privacy Extensions
[ 63.939422] audit(1222700934.686:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=5119 profile="/usr/sbin/cupsd" namespace="default"
[ 66.917200] eth1: link up, 100Mbps, full-duplex, lpa 0x41E1
[ 66.944518] eth0: setting half-duplex.
[ 67.075263] Bluetooth: Core ver 2.11
[ 67.076520] NET: Registered protocol family 31
[ 67.076530] Bluetooth: HCI device and connection manager initialized
[ 67.076537] Bluetooth: HCI socket layer initialized
[ 67.108180] Bluetooth: L2CAP ver 2.9
[ 67.108628] Bluetooth: L2CAP socket layer initialized
[ 67.185504] Bluetooth: RFCOMM socket layer initialized
[ 67.185965] Bluetooth: RFCOMM TTY layer initialized
[ 67.186221] Bluetooth: RFCOMM ver 1.8
[ 67.206509] usb 2-1: new low speed USB device using uhci_hcd and address 6
[ 67.320512] usb 2-1: device descriptor read/64, error -71
[ 67.534506] usb 2-1: device descriptor read/64, error -71
[ 67.737515] usb 2-1: new low speed USB device using uhci_hcd and address 7
[ 67.850522] usb 2-1: device descriptor read/64, error -71
[ 68.064556] usb 2-1: device descriptor read/64, error -71
[ 68.267554] usb 2-1: new low speed USB device using uhci_hcd and address 8
[ 68.675603] usb 2-1: device not accepting address 8, error -71
[ 68.777613] usb 2-1: new low speed USB device using uhci_hcd and address 9
[ 69.185623] usb 2-1: device not accepting address 9, error -71
[ 69.772719] agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
[ 69.772745] agpgart: Device is in legacy mode, falling back to 2.x
[ 69.772752] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
[ 69.772813] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
[ 70.437760] NET: Registered protocol family 17
[ 86.485832] eth1: no IPv6 routers present
[ 99.437868] UDF-fs: Partition marked readonly; forcing readonly mount
[ 99.503521] UDF-fs INFO UDF 0.9.8.1 (2004/29/09) Mounting volume 'CHORALE', timestamp 2008/09/08 19:02 (1078)
[ 190.985118] usb 5-7: new high speed USB device using ehci_hcd and address 7
[ 191.490134] usb 5-7: device not accepting address 7, error -71
[ 191.592170] usb 5-7: new high speed USB device using ehci_hcd and address 8
[ 191.720554] usb 5-7: configuration #1 chosen from 1 choice
[ 191.946254] usbcore: registered new interface driver libusual
[ 191.990234] Initializing USB Mass Storage driver...
[ 192.006193] scsi4 : SCSI emulation for USB Mass Storage devices
[ 192.013302] usbcore: registered new interface driver usb-storage
[ 192.013318] USB Mass Storage support registered.
[ 192.014344] usb-storage: device found at 8
[ 192.014710] usb-storage: waiting for device to settle before scanning
[ 192.273125] usb 5-7: USB disconnect, address 8
[ 192.507222] usb 5-7: new high speed USB device using ehci_hcd and address 9
[ 192.635452] usb 5-7: configuration #1 chosen from 1 choice
[ 192.682261] scsi5 : SCSI emulation for USB Mass Storage devices
[ 192.691500] usb-storage: device found at 9
[ 192.693365] usb-storage: waiting for device to settle before scanning
[ 197.697584] usb-storage: device scan complete
[ 197.698356] scsi 5:0:0:0: Direct-Access USB DISK 20X PMAP PQ: 0 ANSI: 0 CCS
[ 198.189076] sd 5:0:0:0: [sdc] 985088 512-byte hardware sectors (504 MB)
[ 198.190210] sd 5:0:0:0: [sdc] Write Protect is off
[ 198.190223] sd 5:0:0:0: [sdc] Mode Sense: 23 00 00 00
[ 198.190227] sd 5:0:0:0: [sdc] Assuming drive cache: write through
[ 198.193459] sd 5:0:0:0: [sdc] 985088 512-byte hardware sectors (504 MB)
[ 198.194199] sd 5:0:0:0: [sdc] Write Protect is off
[ 198.194208] sd 5:0:0:0: [sdc] Mode Sense: 23 00 00 00
[ 198.194212] sd 5:0:0:0: [sdc] Assuming drive cache: write through
[ 198.194220] sdc: sdc1
[ 198.195207] sd 5:0:0:0: [sdc] Attached SCSI removable disk
[ 198.195279] sd 5:0:0:0: Attached scsi generic sg4 type 0
[ 215.934559] usb 5-7: USB disconnect, address 9
[ 220.508163] usb 5-7: new high speed USB device using ehci_hcd and address 10
[ 220.770184] usb 5-7: new high speed USB device using ehci_hcd and address 11
[ 302.466850] usb 5-7: new high speed USB device using ehci_hcd and address 12
[ 395.055331] usb 5-7: new high speed USB device using ehci_hcd and address 13
[ 396.513409] usb 5-7: new high speed USB device using ehci_hcd and address 20
[ 2645.730295] UDF-fs: Partition marked readonly; forcing readonly mount
[ 2645.777782] UDF-fs INFO UDF 0.9.8.1 (2004/29/09) Mounting volume 'CHORALE', timestamp 2008/09/08 19:02 (1078)
[ 2935.998297] cdrom: This disc doesn't have any tracks I recognize!
[ 3530.520079] eth1: link down
[ 3532.886072] eth1: link up, 100Mbps, full-duplex, lpa 0x41E1
[ 3532.887193] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 3543.221212] eth1: no IPv6 routers present
[ 3574.798443] eth1: no IPv6 routers present
[ 4731.246642] UDF-fs: Partition marked readonly; forcing readonly mount
[ 4731.310285] UDF-fs INFO UDF 0.9.8.1 (2004/29/09) Mounting volume 'CHORALE', timestamp 2008/09/08 19:02 (1078)
[ 6975.956738] usblp0: removed
[ 6976.052991] usb 2-1: new low speed USB device using uhci_hcd and address 10
[ 6976.167003] usb 2-1: device descriptor read/64, error -71
[ 6976.380987] usb 2-1: device descriptor read/64, error -71
[ 6976.585052] usb 2-1: new low speed USB device using uhci_hcd and address 11
[ 6976.698001] usb 2-1: device descriptor read/64, error -71
[ 6976.912045] usb 2-1: device descriptor read/64, error -71
[ 6977.115039] usb 2-1: new low speed USB device using uhci_hcd and address 12
[ 6977.523049] usb 2-1: device not accepting address 12, error -71
[ 6977.625069] usb 2-1: new low speed USB device using uhci_hcd and address 13
[ 6978.033083] usb 2-1: device not accepting address 13, error -71
[ 7430.451593] usb 1-1: USB disconnect, address 4
[ 7438.908150] usb 1-1: new full speed USB device using uhci_hcd and address 6
[ 7439.082097] usb 1-1: configuration #1 chosen from 1 choice
[ 7439.088200] usblp0: USB Bidirectional printer dev 6 if 0 alt 1 proto 2 vid 0x03F0 pid 0x0C17
[ 7440.897286] usb 2-1: new low speed USB device using uhci_hcd and address 14
[ 7441.010296] usb 2-1: device descriptor read/64, error -71
[ 7441.224308] usb 2-1: device descriptor read/64, error -71
[ 7441.427323] usb 2-1: new low speed USB device using uhci_hcd and address 15
[ 7441.540342] usb 2-1: device descriptor read/64, error -71
[ 7441.754346] usb 2-1: device descriptor read/64, error -71
[ 7441.957364] usb 2-1: new low speed USB device using uhci_hcd and address 16
[ 7442.365389] usb 2-1: device not accepting address 16, error -71
[ 7442.467395] usb 2-1: new low speed USB device using uhci_hcd and address 17
[ 7442.875409] usb 2-1: device not accepting address 17, error -71
[ 7487.705337] usblp0: removed
[ 7487.801576] usb 2-1: new low speed USB device using uhci_hcd and address 18
[ 7487.915598] usb 2-1: device descriptor read/64, error -71
[ 7488.129995] usb 2-1: device descriptor read/64, error -71
[ 7488.332632] usb 2-1: new low speed USB device using uhci_hcd and address 19
[ 7488.445587] usb 2-1: device descriptor read/64, error -71
[ 7488.659631] usb 2-1: device descriptor read/64, error -71
[ 7488.862626] usb 2-1: new low speed USB device using uhci_hcd and address 20
[ 7489.270637] usb 2-1: device not accepting address 20, error -71
[ 7489.372659] usb 2-1: new low speed USB device using uhci_hcd and address 21
[ 7489.780698] usb 2-1: device not accepting address 21, error -71
[ 8194.373690] usb 5-7: new high speed USB device using ehci_hcd and address 26

contremaitre · Le 30/09/2008, à 08:42

essaye

sudo rmmod ehci-hcd

Ca devrait faire fonctionner tes ports usb en 1.1 au lieu de 2 donc a vitesse reduite.
Ca résoud souvent ce genre de problème.

Dernière modification par contremaitre (Le 30/09/2008, à 08:42)

zedtux · Le 30/09/2008, à 08:59

Avant de savoir si ca fonctionne, je dis bravo à toi contremaitre !

Par contre, si ca fonctionne, il serai possible de mettre mettre à jour le wiki avec l'erreur device descriptor read/64, error -71 please ?

Mike Yavel · Le 30/09/2008, à 17:40

Yes, ça fonctionne ! merci contremaitre. En revanche, j'hésite à passer mon message en Résolu ( j'ai un peu peur qu'on l'oublie et que je sois obligé de rester en USB 1.1...)

contremaitre · Le 01/10/2008, à 08:29

Cela veut dire que tes connectiques (probablement cable usb, ou peut etre port usb je ne sais pas) ne sont pas de bonne qualité et ne supportent pas le mode USB 2.0 car a cette vitesse il y a des erreurs de lecture.

Une autre solution est de mettre un hub usb, ca resoud souvent les problemes et permet de rester en usb 2.

Mike Yavel · Le 02/10/2008, à 16:01

OK. Merci !

lemmings · Le 30/11/2008, à 22:46

il y a un bug sur launchpad pour ce pb connu :
https://bugs.edge.launchpad.net/bugs/88746

pour l'instant il n'est pas corrigé

Mike Yavel · Le 02/12/2008, à 18:14

Merci pour l'info !

Ubuntu-fr

Navigation

Liens de recherche

Annonce

#1 Le 26/09/2008, à 10:38

Clés USB non détectées [Résolu]

#2 Le 26/09/2008, à 10:49

Re : Clés USB non détectées [Résolu]

#3 Le 26/09/2008, à 10:55

Re : Clés USB non détectées [Résolu]

#4 Le 26/09/2008, à 11:51

Re : Clés USB non détectées [Résolu]

#5 Le 28/09/2008, à 11:13

Re : Clés USB non détectées [Résolu]

#6 Le 29/09/2008, à 07:31

Re : Clés USB non détectées [Résolu]

#7 Le 29/09/2008, à 10:32

Re : Clés USB non détectées [Résolu]

#8 Le 29/09/2008, à 13:06

Re : Clés USB non détectées [Résolu]

#9 Le 29/09/2008, à 15:22

Re : Clés USB non détectées [Résolu]

#10 Le 29/09/2008, à 16:24

Re : Clés USB non détectées [Résolu]

#11 Le 29/09/2008, à 16:47

Re : Clés USB non détectées [Résolu]

#12 Le 29/09/2008, à 17:22

Re : Clés USB non détectées [Résolu]

#13 Le 29/09/2008, à 17:48

Re : Clés USB non détectées [Résolu]

#14 Le 29/09/2008, à 19:25

Re : Clés USB non détectées [Résolu]

#15 Le 30/09/2008, à 08:42

Re : Clés USB non détectées [Résolu]

#16 Le 30/09/2008, à 08:59

Re : Clés USB non détectées [Résolu]

#17 Le 30/09/2008, à 17:40

Re : Clés USB non détectées [Résolu]

#18 Le 01/10/2008, à 08:29

Re : Clés USB non détectées [Résolu]

#19 Le 02/10/2008, à 16:01

Re : Clés USB non détectées [Résolu]

#20 Le 30/11/2008, à 22:46

Re : Clés USB non détectées [Résolu]

#21 Le 02/12/2008, à 18:14

Re : Clés USB non détectées [Résolu]

Pied de page des forums