Pages : 1
#1 Le 10/11/2018, à 19:27
- riphraph
avis sur rapport smartmontools
Bonjour !
Après quelques plantages sous ubuntu 16, je suis passé sous ubuntu 18.04 et l'installation s'est faite partiellement.
J'ai tenté de réinstaller ubuntu 18.04 sur la même partition depuis un live usb, et celle ci a échoué et préconisé des commandes comme fsck, qui n'indique pas d'erreur :
sudo fsck /dev/sdb6
fsck de util-linux 2.31.1
e2fsck 1.44.1 (24-Mar-2018)
/dev/sdb6 : propre, 15425/2272928 fichiers, 825368/9087402 blocsJ'ai fait un formatage de la partition racine, et j'ai supprimé l'ancien swap et regroupé les 2 partitions.
L'installation plante toujours.
J'ai lancé une analyse smartmontools. J'aurais bien voulu installer gsmartcontrol mais je ne sais pas trop comment.
Voici le rapport :
sudo smartctl -q errorsonly -H -l selftest /dev/sdb6
ubuntu@ubuntu:~$ sudo smartctl -s on -a /dev/sdb6
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.15.0-29-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Scorpio Blue Serial ATA
Device Model: WDC WD3200BEVT-22A23T0
Serial Number: WD-WX81A7025543
LU WWN Device Id: 5 0014ee 204cf1830
Firmware Version: 01.01A01
User Capacity: 320072933376 bytes [320 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Sat Nov 10 17:20:09 2018 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 243) Self-test routine in progress...
30% of test remaining.
Total time to complete Offline
data collection: ( 7980) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 95) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x7037) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 22
3 Spin_Up_Time 0x0027 153 130 021 Pre-fail Always - 1341
4 Start_Stop_Count 0x0032 093 093 000 Old_age Always - 7134
5 Reallocated_Sector_Ct 0x0033 168 168 140 Pre-fail Always - 351
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 084 084 000 Old_age Always - 12178
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 096 096 000 Old_age Always - 4951
191 G-Sense_Error_Rate 0x0032 001 001 000 Old_age Always - 16401
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 287
193 Load_Cycle_Count 0x0032 162 162 000 Old_age Always - 115216
194 Temperature_Celsius 0x0022 105 092 000 Old_age Always - 38
196 Reallocated_Event_Count 0x0032 167 167 000 Old_age Always - 33
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0
SMART Error Log Version: 1
Warning: ATA error count 58433 inconsistent with error log pointer 2
ATA Error Count: 58433 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 58433 occurred at disk power-on lifetime: 12177 hours (507 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 02 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 02 00 00 00 a0 00 01:00:41.799 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 01:00:41.798 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 01:00:41.798 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 00 01:00:41.797 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 01:00:41.796 IDENTIFY DEVICE
Error 58432 occurred at disk power-on lifetime: 12177 hours (507 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 46 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 03 46 00 00 00 a0 00 01:00:41.798 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 00 01:00:41.797 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 01:00:41.796 IDENTIFY DEVICE
ef 10 02 00 00 00 a0 00 01:00:41.779 SET FEATURES [Enable SATA feature]
Error 58431 occurred at disk power-on lifetime: 12177 hours (507 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 02 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 02 00 00 00 a0 00 01:00:41.797 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 01:00:41.796 IDENTIFY DEVICE
ef 10 02 00 00 00 a0 00 01:00:41.779 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 01:00:41.778 IDENTIFY DEVICE
Error 58430 occurred at disk power-on lifetime: 12177 hours (507 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 02 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 10 02 00 00 00 a0 00 01:00:41.779 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 01:00:41.778 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 01:00:41.778 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 00 01:00:41.777 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 00 01:00:41.776 IDENTIFY DEVICE
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.Merci pour votre aide,
Dernière modification par riphraph (Le 11/11/2018, à 05:20)
Hors ligne
#2 Le 10/11/2018, à 21:30
- Nuliel
Re : avis sur rapport smartmontools
191 G-Sense_Error_Rate 0x0032 001 001 000 Old_age Always - 16401
Il a fait un saut en parachute récemment ce disque? 
Faut déplacer doucement le disque lorsqu'il est en fonctionnement!!!!!!!!
5 Reallocated_Sector_Ct 0x0033 168 168 140 Pre-fail Always - 351
196 Reallocated_Event_Count 0x0032 167 167 000 Old_age Always - 33
Déjà 351 secteurs réalloués, c'est beaucoup.
193 Load_Cycle_Count 0x0032 162 162 000 Old_age Always - 115216
Ce disque a peut être un problème de parcage.
Error 58433 occurred at disk power-on lifetime: 12177 hours (507 days + 9 hours)
Donc 58433 erreurs, c'est ENORME, et les erreurs loguées sont très récentes.
Warning: ATA error count 58433 inconsistent with error log pointer 2
Aucune idée de ce que ça veut dire, mais ça n'a pas l'air bon (la partie électronique qui en a marre de voir passer des erreurs?)
Dernière modification par Nuliel (Le 10/11/2018, à 21:31)
Hors ligne
#3 Le 12/11/2018, à 01:55
- riphraph
Re : avis sur rapport smartmontools
merci pour ta réponse,
pourtant je fais attention, peut etre qu'au bout de huit ans, ce pc portable aurait besoin d'un disque frais.
recemment j'ai fait beaucoup de sauvegardes.
j'ai pu réaliser l'installation en modifiant la taille des partitions. du coup en ecrivant sur une autre partie voisine du disque plus saine et en transferant la partie endommagée à la partition windows voisine.
Je me pose tout de même la question de comment réparer mon disque, ou au moins le préserver.
Hors ligne
Pages : 1