#1 Le 04/11/2019, à 19:34
- Ulipap
[Résolu] Interprétation de résultats issus de smartctl
Bonjour
J'ai changé un disque dur sur un PC qui ne démarrait plus.
Je voudrais savoir si le DD changé peut être utilisé en DD externe en le reformattant
Voici les logs : Je vois des erreurs mais est ce si grave ?
J'ai essayé de lancer plusieurs tests mais aucun ne va jusqu'au bout.
Merci d'avance
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.15.0-66-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: WDC WD20EZRZ-60Z5HB0
Serial Number: WD-WCC4M6FXD2YE
LU WWN Device Id: 5 0014ee 2b89e3678
Firmware Version: 81.00A81
User Capacity: 2 000 398 934 016 bytes [2,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 3.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-3 T13/2161-D revision 5
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Mon Nov 4 19:31:03 2019 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 121) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: (26100) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 285) minutes.
SCT capabilities: (0x303d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 198 198 051 Pre-fail Always - 79953
3 Spin_Up_Time 0x0027 182 172 021 Pre-fail Always - 3883
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1518
5 Reallocated_Sector_Ct 0x0033 199 199 140 Pre-fail Always - 53
7 Seek_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
9 Power_On_Hours 0x0032 090 090 000 Old_age Always - 7411
10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1515
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0033 100 100 097 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 66523
188 Command_Timeout 0x0032 001 001 000 Old_age Always - 21486815335
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 78
193 Load_Cycle_Count 0x0032 161 161 000 Old_age Always - 117994
194 Temperature_Celsius 0x0022 115 102 000 Old_age Always - 32 (Min/Max 20/38)
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 27
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 28
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 13
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed: read failure 90% 7411 2057816
# 2 Short offline Completed: read failure 50% 7399 2057816
# 3 Extended offline Completed: read failure 90% 7388 318031
# 4 Extended offline Completed: read failure 90% 7388 318028
# 5 Extended offline Completed: read failure 90% 7388 333456
# 6 Short offline Completed: read failure 60% 7388 336160
# 7 Short offline Completed: read failure 90% 7387 318031
# 8 Short offline Completed: read failure 90% 7387 318026
# 9 Short offline Completed without error 00% 2234 -
#10 Short offline Completed without error 00% 2 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.Dernière modification par Ulipap (Le 05/11/2019, à 21:58)
Hors ligne
#2 Le 04/11/2019, à 23:56
- rmy
Re : [Résolu] Interprétation de résultats issus de smartctl
Secteurs HS et en attente de réallocation : disque à mettre au rebut.
récupération de données: vrac–topic unique–mon site pro pour les particuliers : www.diskcard.fr– Je recycle volontiers tous vos disques durs HS (ou pas).
Le site pro pour les pros, spécialiste recupération de données RAID, NAS et serveurs: www.vodata.fr
Hors ligne
#3 Le 05/11/2019, à 08:29
- serged
Re : [Résolu] Interprétation de résultats issus de smartctl
LinuxMint Vera Cinnamon et d'autres machines en MATE, XFCE... 20.x , 21.x ou 19.x
Tour : Asus F2A55 / AMD A8-5600K APU 3,6GHz / RAM 16Go / Nvidia GeForce GT610 / LM21.1 Cinnamon
Portable : LDLC Mercure MH : Celeron N3450 /RAM 4Go / Intel HD graphics 500 i915 / biboot Win 10 (sur SSD) - LM21.1 MATE (sur HDD)
Hors ligne
#4 Le 05/11/2019, à 21:57
- Ulipap
Re : [Résolu] Interprétation de résultats issus de smartctl
Merci à vous
Hors ligne