#26 Le 10/04/2020, à 15:32
- geole
Re : Disque dur externe contenu inconnu
Ce comportement est drôle.
Toutes les écritures de 1000 secteurs sont officiellement bonnes.
Mais cela a duré entre 0,00433008 seconde , avec un débit surréaliste de 946 MB/s
et 34,0438 secondes , avec un débit de 120 kB/s . Il y a certainement eu plein de difficultés à faire accepter les écritures.
Ce n'est qu'à partir du secteur physique 40000 que cela est devenu lisible.
Je serais curieux d'avoir un nouvel état smartcl pourvoir s'il a fait des réparations.
Il n'y a plus rien à tirer de ce disque. Il peut écrire dans le début du disque et ne peut pas le relire quelques minutes plus tard....
Ce n'est probablement pas la partie physique mais la partie électronique du disque qui ne fonctionne plus correctement.
Les grilles de l'installateur https://doc.ubuntu-fr.org/tutoriel/inst … _subiquity
"gedit admin:///etc/fstab" est proscrit, utilisez "pkexec env DISPLAY=$DISPLAY XAUTHORITY=$XAUTHORITY xdg-open /etc/fstab" Voir https://doc.ubuntu-fr.org/gedit
Les partitions EXT4 des disques externes => https://forum.ubuntu-fr.org/viewtopic.p … #p22697248
Hors ligne
#27 Le 10/04/2020, à 15:55
- Julien.Me
Re : Disque dur externe contenu inconnu
Voici pour le smartctl :
sudo smartctl -s on -a /dev/sdc
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.15.0-33-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Elements / My Passport (USB, AF)
Device Model: WDC WD10JMVW-11AJGS0
Serial Number: WD-WXC1EC2K3002
LU WWN Device Id: 5 0014ee 6035f4adf
Firmware Version: 01.01A01
User Capacity: 1000204886016 bytes [1,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Fri Apr 10 16:53:51 2020 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART Status not supported: Incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
Warning: This result is based on an Attribute check.
See vendor-specific Attribute list for failed Attributes.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (18720) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 209) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x7035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 189 189 051 Pre-fail Always - 48233
3 Spin_Up_Time 0x0027 171 163 021 Pre-fail Always - 2425
4 Start_Stop_Count 0x0032 098 098 000 Old_age Always - 2544
5 Reallocated_Sector_Ct 0x0033 133 133 140 Pre-fail Always FAILING_NOW 2829
7 Seek_Error_Rate 0x002e 135 131 000 Old_age Always - 17157
9 Power_On_Hours 0x0032 090 090 000 Old_age Always - 7589
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 789
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 341
193 Load_Cycle_Count 0x0032 194 194 000 Old_age Always - 18507
194 Temperature_Celsius 0x0022 113 086 000 Old_age Always - 34
196 Reallocated_Event_Count 0x0032 001 001 000 Old_age Always - 2738
197 Current_Pending_Sector 0x0032 200 182 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 61
SMART Error Log Version: 1
ATA Error Count: 26 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 26 occurred at disk power-on lifetime: 7555 hours (314 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 02 00 00 00 00
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
e1 00 02 00 00 00 00 00 01:53:15.261 IDLE IMMEDIATE
ec 00 01 00 00 00 00 00 01:53:15.261 IDENTIFY DEVICE
b0 d0 00 00 4f c2 00 00 01:53:07.951 SMART READ DATA
Error 25 occurred at disk power-on lifetime: 7555 hours (314 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 02 00 00 00 00
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
e1 00 02 00 00 00 00 00 01:52:36.234 IDLE IMMEDIATE
ec 00 01 00 00 00 00 00 01:52:36.233 IDENTIFY DEVICE
e1 00 0f 00 00 00 00 00 01:52:34.023 IDLE IMMEDIATE
e1 00 02 00 00 00 00 00 01:52:33.910 IDLE IMMEDIATE
ec 00 01 00 00 00 00 00 01:52:33.910 IDENTIFY DEVICE
Error 24 occurred at disk power-on lifetime: 7555 hours (314 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 0f 00 00 00 00
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
e1 00 0f 00 00 00 00 00 01:52:34.023 IDLE IMMEDIATE
e1 00 02 00 00 00 00 00 01:52:33.910 IDLE IMMEDIATE
ec 00 01 00 00 00 00 00 01:52:33.910 IDENTIFY DEVICE
ec 00 01 00 00 00 40 00 01:52:17.867 IDENTIFY DEVICE
Error 23 occurred at disk power-on lifetime: 7555 hours (314 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 02 00 00 00 00
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
e1 00 02 00 00 00 00 00 01:52:33.910 IDLE IMMEDIATE
ec 00 01 00 00 00 00 00 01:52:33.910 IDENTIFY DEVICE
ec 00 01 00 00 00 40 00 01:52:17.867 IDENTIFY DEVICE
Error 22 occurred at disk power-on lifetime: 7555 hours (314 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 02 00 00 00 00
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
e1 00 02 00 00 00 00 00 01:48:59.665 IDLE IMMEDIATE
ec 00 01 00 00 00 00 00 01:48:59.664 IDENTIFY DEVICE
b0 d0 00 00 4f c2 00 00 01:48:52.360 SMART READ DATA
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed: read failure 90% 7559 4448
# 2 Short offline Completed: read failure 90% 7421 0
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.Le disque dur est donc bien irrécupérable ?
Hors ligne
#28 Le 10/04/2020, à 16:16
- geole
Re : Disque dur externe contenu inconnu
Julien.Me a écrit :
Voici pour le smartctl :
sudo smartctl -s on -a /dev/sdc smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.15.0-33-generic] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Elements / My Passport (USB, AF) Device Model: WDC WD10JMVW-11AJGS === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: FAILED! Drive failure expected in less than 24 hours. SAVE ALL DATA. Warning: This result is based on an Attribute check. See vendor-specific Attribute list for failed Attributes. ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 189 189 051 Pre-fail Always - 48233 5 Reallocated_Sector_Ct 0x0033 133 133 140 Pre-fail Always FAILING_NOW 2829 9 Power_On_Hours 0x0032 090 090 000 Old_age Always - 7589 196 Reallocated_Event_Count 0x0032 001 001 000 Old_age Always - 2738 197 Current_Pending_Sector 0x0032 200 182 000 Old_age Always - 0Le disque dur est donc bien irrécupérable ?
Le problème est que le secteur 0 n'est toujours pas lisible... Donc impossible de créer une table de partition en mode ms-dos
Et je ne sais pas si on peut créer une table de partition GPT uniquement en fin de disque.
Lorsqu'un disque est failing, windows refuse de l'utiliser en écriture.
De plus, on n'a rien regardé au-delà des secteurs 40.000.
Donc, le disque est inutilisable malgré son jeune âge!
Dernière modification par geole (Le 11/04/2020, à 16:51)
Les grilles de l'installateur https://doc.ubuntu-fr.org/tutoriel/inst … _subiquity
"gedit admin:///etc/fstab" est proscrit, utilisez "pkexec env DISPLAY=$DISPLAY XAUTHORITY=$XAUTHORITY xdg-open /etc/fstab" Voir https://doc.ubuntu-fr.org/gedit
Les partitions EXT4 des disques externes => https://forum.ubuntu-fr.org/viewtopic.p … #p22697248
Hors ligne
#29 Le 11/04/2020, à 13:39
- Julien.Me
Re : Disque dur externe contenu inconnu
Bonjour,
Merci beaucoup d'avoir tenté de réparer ce disque parti trop tôt ! J'ai pu au moins en apprendre un peu plus.
Hors ligne