Wifi Realtek modèle rtl8723bs, je n'arrive pas à le configurer dans 19

Barrab · Le 11/04/2020, à 19:02

Je ne suis pas technicien en informatique mais, d'après cet article mon problème se situe plus du côté du port SDIO que du côté de la carte wifi. C'est comme si le SDIO n'est pas obligé de se connecter à la carte WIFI. Il faut faire des manipulations pour que la connexion se fasse entre les deux. Je n'ai pas les connaissances ni les permissions de l'OS pour le faire

Je vous invite à y jeter un coup d'oeil

https://www.silabs.com/community/wirele … ction-ajSx

Nuliel · Le 11/04/2020, à 20:51

Tu peux redémarrer et donner

dmesg

(c'est long c'est normal)

et aussi

 ls -R /sys/bus/sdio/devices/

Dernière modification par Nuliel (Le 11/04/2020, à 20:53)

Barrab · Le 11/04/2020, à 21:13

demsg après redémarrage

jean@jean-Switch-One-SW1-011:~$ dmesg
[    0.000000] microcode: microcode updated early to revision 0x411, date = 2019-04-23
[    0.000000] Linux version 5.3.0-46-generic (buildd@lgw01-amd64-003) (gcc version 9.2.1 20191008 (Ubuntu 9.2.1-9ubuntu2)) #38-Ubuntu SMP Fri Mar 27 17:37:05 UTC 2020 (Ubuntu 5.3.0-46.38-generic 5.3.18)
[    0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-5.3.0-46-generic root=UUID=6806b4ca-3f10-4b04-8bc2-0f5fcb3e6c8e ro quiet splash vt.handoff=7
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   Hygon HygonGenuine
[    0.000000]   Centaur CentaurHauls
[    0.000000]   zhaoxin   Shanghai  
[    0.000000] x86/fpu: x87 FPU will use FXSAVE
[    0.000000] BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000008efff] usable
[    0.000000] BIOS-e820: [mem 0x000000000008f000-0x000000000008ffff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x0000000000090000-0x000000000009dfff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009e000-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001fffffff] usable
[    0.000000] BIOS-e820: [mem 0x0000000020000000-0x00000000201fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000020200000-0x000000007b0b3fff] usable
[    0.000000] BIOS-e820: [mem 0x000000007b0b4000-0x000000007b0e3fff] reserved
[    0.000000] BIOS-e820: [mem 0x000000007b0e4000-0x000000007b115fff] ACPI data
[    0.000000] BIOS-e820: [mem 0x000000007b116000-0x000000007b70ffff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x000000007b710000-0x000000007ba54fff] reserved
[    0.000000] BIOS-e820: [mem 0x000000007ba55000-0x000000007bffffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000e3ffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fea00000-0x00000000feafffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed01000-0x00000000fed01fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed03000-0x00000000fed03fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed06000-0x00000000fed06fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed08000-0x00000000fed09fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1cfff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed80000-0x00000000fedbffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ffc00000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000017fffffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] efi: EFI v2.40 by American Megatrends
[    0.000000] efi:  ESRT=0x7b0e2000  ACPI=0x7b0ee000  ACPI 2.0=0x7b0ee000  SMBIOS=0x7b8da000  SMBIOS 3.0=0x7b8d9000  TPMEventLog=0x78177018 
[    0.000000] secureboot: Secure boot disabled
[    0.000000] SMBIOS 3.0.0 present.
[    0.000000] DMI: Acer Switch One SW1-011/Okinawa, BIOS 1.09 01/14/2017
[    0.000000] tsc: Detected 1440.000 MHz processor
[    0.000301] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000308] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000330] last_pfn = 0x180000 max_arch_pfn = 0x400000000
[    0.000339] MTRR default type: uncachable
[    0.000341] MTRR fixed ranges enabled:
[    0.000345]   00000-9FFFF write-back
[    0.000349]   A0000-FFFFF write-protect
[    0.000352] MTRR variable ranges enabled:
[    0.000356]   0 base 000000000 mask F80000000 write-back
[    0.000360]   1 base 07E000000 mask FFE000000 uncachable
[    0.000363]   2 base 07D000000 mask FFF000000 uncachable
[    0.000366]   3 base 07C800000 mask FFF800000 uncachable
[    0.000369]   4 base 100000000 mask F80000000 write-back
[    0.000372]   5 base 07C400000 mask FFFC00000 uncachable
[    0.000374]   6 disabled
[    0.000376]   7 disabled
[    0.000507] x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WP  UC- WT  
[    0.000640] total RAM covered: 4036M
[    0.001857] Found optimal setting for mtrr clean up
[    0.001860]  gran_size: 64K 	chunk_size: 64M 	num_reg: 6  	lose cover RAM: 0G
[    0.002011] e820: update [mem 0x7c400000-0xffffffff] usable ==> reserved
[    0.002019] last_pfn = 0x7c000 max_arch_pfn = 0x400000000
[    0.019152] esrt: ESRT header is not in the memory map.
[    0.019179] check: Scanning 1 areas for low memory corruption
[    0.019196] BRK [0x146401000, 0x146401fff] PGTABLE
[    0.019203] BRK [0x146402000, 0x146402fff] PGTABLE
[    0.019206] BRK [0x146403000, 0x146403fff] PGTABLE
[    0.019406] BRK [0x146404000, 0x146404fff] PGTABLE
[    0.019411] BRK [0x146405000, 0x146405fff] PGTABLE
[    0.019978] BRK [0x146406000, 0x146406fff] PGTABLE
[    0.020125] BRK [0x146407000, 0x146407fff] PGTABLE
[    0.020370] BRK [0x146408000, 0x146408fff] PGTABLE
[    0.020848] RAMDISK: [mem 0x3d250000-0x3fffdfff]
[    0.020873] ACPI: Early table checksum verification disabled
[    0.020882] ACPI: RSDP 0x000000007B0EE000 000024 (v02 ALASKA)
[    0.020890] ACPI: XSDT 0x000000007B0EE0A8 0000D4 (v01 ALASKA A M I    01072009 AMI  00010013)
[    0.020907] ACPI: FACP 0x000000007B10F1B0 00010C (v05 ALASKA A M I    01072009 AMI  00010013)
[    0.020923] ACPI: DSDT 0x000000007B0EE210 020F9A (v02 ALASKA A M I    01072009 INTL 20120913)
[    0.020934] ACPI: FACS 0x000000007B70FF80 000040
[    0.020941] ACPI: APIC 0x000000007B10F2C0 000084 (v03 ALASKA A M I    01072009 AMI  00010013)
[    0.020949] ACPI: FPDT 0x000000007B10F348 000044 (v01 ALASKA A M I    01072009 AMI  00010013)
[    0.020958] ACPI: FIDT 0x000000007B10F390 00009C (v01 ALASKA A M I    01072009 AMI  00010013)
[    0.020966] ACPI: MSDM 0x000000007B10F430 000055 (v03 ALASKA A M I    01072009 AMI  00010013)
[    0.020975] ACPI: MCFG 0x000000007B10F488 00003C (v01 ALASKA A M I    01072009 MSFT 00000097)
[    0.020983] ACPI: SSDT 0x000000007B10F4C8 00415C (v01 DptfTb DptfTab  00001000 INTL 20120913)
[    0.020993] ACPI: SSDT 0x000000007B113628 000612 (v01 CpuDpf CpuDptf  00001000 INTL 20120913)
[    0.021001] ACPI: SSDT 0x000000007B113C40 000058 (v01 LowPM  LowPwrM  00001000 INTL 20120913)
[    0.021010] ACPI: UEFI 0x000000007B113C98 000042 (v01 ALASKA A M I    00000000      00000000)
[    0.021018] ACPI: SSDT 0x000000007B113CE0 000269 (v01 UsbCTb UsbCTab  00001000 INTL 20120913)
[    0.021027] ACPI: HPET 0x000000007B113F50 000038 (v01 ALASKA A M I    01072009 AMI. 00000005)
[    0.021035] ACPI: SSDT 0x000000007B113F88 000763 (v01 PmRef  CpuPm    00003000 INTL 20120913)
[    0.021044] ACPI: SSDT 0x000000007B1146F0 000262 (v01 PmRef  Cpu0Tst  00003000 INTL 20120913)
[    0.021053] ACPI: SSDT 0x000000007B114958 00017A (v01 PmRef  ApTst    00003000 INTL 20120913)
[    0.021061] ACPI: LPIT 0x000000007B114AD8 000104 (v01 ALASKA A M I    00000005 MSFT 0100000D)
[    0.021072] ACPI: BCFG 0x000000007B114BE0 000139 (v01 INTEL  BATTCONF 00000001 ACPI 00000000)
[    0.021080] ACPI: PRAM 0x000000007B114D20 000030 (v01                 00000001      00000000)
[    0.021088] ACPI: BGRT 0x000000007B114D50 000038 (v01 ALASKA A M I    01072009 AMI  00010013)
[    0.021097] ACPI: TPM2 0x000000007B114D88 000034 (v03        Tpm2Tabl 00000001 AMI  00000000)
[    0.021105] ACPI: CSRT 0x000000007B114DC0 00014C (v00 INTEL  LANFORDC 00000005 MSFT 0100000D)
[    0.021114] ACPI: WDAT 0x000000007B114F10 000104 (v01                 00000000      00000000)
[    0.021138] ACPI: Local APIC address 0xfee00000
[    0.021437] No NUMA configuration found
[    0.021442] Faking a node at [mem 0x0000000000000000-0x000000017fffffff]
[    0.021470] NODE_DATA(0) allocated [mem 0x17ffd4000-0x17fffefff]
[    0.022400] Zone ranges:
[    0.022405]   DMA      [mem 0x0000000000001000-0x0000000000ffffff]
[    0.022409]   DMA32    [mem 0x0000000001000000-0x00000000ffffffff]
[    0.022412]   Normal   [mem 0x0000000100000000-0x000000017fffffff]
[    0.022416]   Device   empty
[    0.022420] Movable zone start for each node
[    0.022430] Early memory node ranges
[    0.022433]   node   0: [mem 0x0000000000001000-0x000000000008efff]
[    0.022437]   node   0: [mem 0x0000000000090000-0x000000000009dfff]
[    0.022439]   node   0: [mem 0x0000000000100000-0x000000001fffffff]
[    0.022442]   node   0: [mem 0x0000000020200000-0x000000007b0b3fff]
[    0.022444]   node   0: [mem 0x000000007ba55000-0x000000007bffffff]
[    0.022447]   node   0: [mem 0x0000000100000000-0x000000017fffffff]
[    0.022900] Zeroed struct page in unavailable ranges: 19461 pages
[    0.022905] Initmem setup node 0 [mem 0x0000000000001000-0x000000017fffffff]
[    0.022910] On node 0 totalpages: 1029115
[    0.022914]   DMA zone: 64 pages used for memmap
[    0.022916]   DMA zone: 21 pages reserved
[    0.022918]   DMA zone: 3996 pages, LIFO batch:0
[    0.023089]   DMA32 zone: 7826 pages used for memmap
[    0.023092]   DMA32 zone: 500831 pages, LIFO batch:63
[    0.051357]   Normal zone: 8192 pages used for memmap
[    0.051359]   Normal zone: 524288 pages, LIFO batch:63
[    0.072136] Reserving Intel graphics memory at [mem 0x7ce00000-0x7edfffff]
[    0.072231] ACPI: PM-Timer IO Port: 0x408
[    0.072237] ACPI: Local APIC address 0xfee00000
[    0.072257] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.072260] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[    0.072262] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[    0.072264] ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
[    0.072288] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-114
[    0.072296] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.072300] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.072303] ACPI: IRQ0 used by override.
[    0.072306] ACPI: IRQ9 used by override.
[    0.072314] Using ACPI (MADT) for SMP configuration information
[    0.072318] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.072340] e820: update [mem 0x79e74000-0x79ee5fff] usable ==> reserved
[    0.072368] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
[    0.072470] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[    0.072477] PM: Registered nosave memory: [mem 0x0008f000-0x0008ffff]
[    0.072482] PM: Registered nosave memory: [mem 0x0009e000-0x0009ffff]
[    0.072484] PM: Registered nosave memory: [mem 0x000a0000-0x000fffff]
[    0.072490] PM: Registered nosave memory: [mem 0x20000000-0x201fffff]
[    0.072495] PM: Registered nosave memory: [mem 0x79e74000-0x79ee5fff]
[    0.072501] PM: Registered nosave memory: [mem 0x7b0b4000-0x7b0e3fff]
[    0.072503] PM: Registered nosave memory: [mem 0x7b0e4000-0x7b115fff]
[    0.072505] PM: Registered nosave memory: [mem 0x7b116000-0x7b70ffff]
[    0.072507] PM: Registered nosave memory: [mem 0x7b710000-0x7ba54fff]
[    0.072513] PM: Registered nosave memory: [mem 0x7c000000-0x7cdfffff]
[    0.072515] PM: Registered nosave memory: [mem 0x7ce00000-0x7edfffff]
[    0.072516] PM: Registered nosave memory: [mem 0x7ee00000-0xdfffffff]
[    0.072518] PM: Registered nosave memory: [mem 0xe0000000-0xe3ffffff]
[    0.072520] PM: Registered nosave memory: [mem 0xe4000000-0xfe9fffff]
[    0.072522] PM: Registered nosave memory: [mem 0xfea00000-0xfeafffff]
[    0.072524] PM: Registered nosave memory: [mem 0xfeb00000-0xfebfffff]
[    0.072526] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[    0.072528] PM: Registered nosave memory: [mem 0xfec01000-0xfed00fff]
[    0.072530] PM: Registered nosave memory: [mem 0xfed01000-0xfed01fff]
[    0.072531] PM: Registered nosave memory: [mem 0xfed02000-0xfed02fff]
[    0.072533] PM: Registered nosave memory: [mem 0xfed03000-0xfed03fff]
[    0.072535] PM: Registered nosave memory: [mem 0xfed04000-0xfed05fff]
[    0.072537] PM: Registered nosave memory: [mem 0xfed06000-0xfed06fff]
[    0.072539] PM: Registered nosave memory: [mem 0xfed07000-0xfed07fff]
[    0.072541] PM: Registered nosave memory: [mem 0xfed08000-0xfed09fff]
[    0.072543] PM: Registered nosave memory: [mem 0xfed0a000-0xfed1bfff]
[    0.072545] PM: Registered nosave memory: [mem 0xfed1c000-0xfed1cfff]
[    0.072546] PM: Registered nosave memory: [mem 0xfed1d000-0xfed7ffff]
[    0.072548] PM: Registered nosave memory: [mem 0xfed80000-0xfedbffff]
[    0.072550] PM: Registered nosave memory: [mem 0xfedc0000-0xfedfffff]
[    0.072552] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[    0.072554] PM: Registered nosave memory: [mem 0xfee01000-0xffbfffff]
[    0.072556] PM: Registered nosave memory: [mem 0xffc00000-0xffffffff]
[    0.072562] [mem 0x7ee00000-0xdfffffff] available for PCI devices
[    0.072566] Booting paravirtualized kernel on bare hardware
[    0.072573] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
[    0.072599] setup_percpu: NR_CPUS:8192 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1
[    0.073616] percpu: Embedded 54 pages/cpu s184320 r8192 d28672 u524288
[    0.073644] pcpu-alloc: s184320 r8192 d28672 u524288 alloc=1*2097152
[    0.073647] pcpu-alloc: [0] 0 1 2 3 
[    0.073762] Built 1 zonelists, mobility grouping on.  Total pages: 1013012
[    0.073764] Policy zone: Normal
[    0.073769] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-5.3.0-46-generic root=UUID=6806b4ca-3f10-4b04-8bc2-0f5fcb3e6c8e ro quiet splash vt.handoff=7
[    0.075316] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[    0.076024] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[    0.076121] mem auto-init: stack:off, heap alloc:on, heap free:off
[    0.098685] Calgary: detecting Calgary via BIOS EBDA area
[    0.098689] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.132273] Memory: 3851344K/4116460K available (14339K kernel code, 2387K rwdata, 4724K rodata, 2676K init, 5044K bss, 265116K reserved, 0K cma-reserved)
[    0.132808] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.132847] Kernel/User page tables isolation: enabled
[    0.132888] ftrace: allocating 43582 entries in 171 pages
[    0.169593] rcu: Hierarchical RCU implementation.
[    0.169599] rcu: 	RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=4.
[    0.169600] 	Tasks RCU enabled.
[    0.169603] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.169605] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.181017] NR_IRQS: 524544, nr_irqs: 1024, preallocated irqs: 16
[    0.181591] random: crng done (trusting CPU's manufacturer)
[    0.181675] vt handoff: transparent VT on vt#7
[    0.181695] Console: colour dummy device 80x25
[    0.181704] printk: console [tty0] enabled
[    0.181759] ACPI: Core revision 20190703
[    0.182374] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484882848 ns
[    0.182407] APIC: Switch to symmetric I/O mode setup
[    0.184159] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0
[    0.202413] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x14c1baf3789, max_idle_ns: 440795266465 ns
[    0.202422] Calibrating delay loop (skipped), value calculated using timer frequency.. 2880.00 BogoMIPS (lpj=5760000)
[    0.202428] pid_max: default: 32768 minimum: 301
[    0.207533] LSM: Security Framework initializing
[    0.207572] Yama: becoming mindful.
[    0.207670] AppArmor: AppArmor initialized
[    0.207797] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.207823] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.208330] *** VALIDATE proc ***
[    0.208507] *** VALIDATE cgroup1 ***
[    0.208513] *** VALIDATE cgroup2 ***
[    0.208641] mce: CPU0: Thermal monitoring enabled (TM1)
[    0.208648] process: using mwait in idle threads
[    0.208656] Last level iTLB entries: 4KB 48, 2MB 0, 4MB 0
[    0.208658] Last level dTLB entries: 4KB 256, 2MB 16, 4MB 16, 1GB 0
[    0.208667] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization
[    0.208672] Spectre V2 : Mitigation: Full generic retpoline
[    0.208675] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[    0.208678] Spectre V2 : Enabling Restricted Speculation for firmware calls
[    0.208682] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier
[    0.208687] MDS: Mitigation: Clear CPU buffers
[    0.209071] Freeing SMP alternatives memory: 36K
[    0.212867] TSC deadline timer enabled
[    0.212876] smpboot: CPU0: Intel(R) Atom(TM) x5-Z8350  CPU @ 1.44GHz (family: 0x6, model: 0x4c, stepping: 0x4)
[    0.213421] Performance Events: PEBS fmt2+, 8-deep LBR, Silvermont events, 8-deep LBR, full-width counters, Intel PMU driver.
[    0.213436] ... version:                3
[    0.213438] ... bit width:              40
[    0.213439] ... generic registers:      2
[    0.213441] ... value mask:             000000ffffffffff
[    0.213443] ... max period:             0000007fffffffff
[    0.213444] ... fixed-purpose events:   3
[    0.213446] ... event mask:             0000000700000003
[    0.213577] rcu: Hierarchical SRCU implementation.
[    0.214416] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
[    0.214416] smp: Bringing up secondary CPUs ...
[    0.214416] x86: Booting SMP configuration:
[    0.214416] .... node  #0, CPUs:      #1 #2 #3
[    0.219048] smp: Brought up 1 node, 4 CPUs
[    0.219048] smpboot: Max logical packages: 1
[    0.219048] smpboot: Total of 4 processors activated (11520.00 BogoMIPS)
[    0.219829] devtmpfs: initialized
[    0.219829] x86/mm: Memory block size: 128MB
[    0.223005] PM: Registering ACPI NVS region [mem 0x0008f000-0x0008ffff] (4096 bytes)
[    0.223005] PM: Registering ACPI NVS region [mem 0x7b116000-0x7b70ffff] (6266880 bytes)
[    0.223005] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.223005] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.223005] pinctrl core: initialized pinctrl subsystem
[    0.223014] PM: RTC time: 20:04:13, date: 2020-04-11
[    0.223430] NET: Registered protocol family 16
[    0.223723] audit: initializing netlink subsys (disabled)
[    0.223780] audit: type=2000 audit(1586635453.040:1): state=initialized audit_enabled=0 res=1
[    0.223780] EISA bus registered
[    0.223780] cpuidle: using governor ladder
[    0.223780] cpuidle: using governor menu
[    0.223780] ACPI: bus type PCI registered
[    0.223780] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.223780] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.223780] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[    0.223780] PCI: MMCONFIG for 0000 [bus00-3f] at [mem 0xe0000000-0xe3ffffff] (base 0xe0000000) (size reduced!)
[    0.223780] PCI: Using configuration type 1 for base access
[    0.226986] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[    0.231366] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.242727] ACPI: Added _OSI(Module Device)
[    0.242730] ACPI: Added _OSI(Processor Device)
[    0.242732] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.242734] ACPI: Added _OSI(Processor Aggregator Device)
[    0.242737] ACPI: Added _OSI(Linux-Dell-Video)
[    0.242740] ACPI: Added _OSI(Linux-Lenovo-NV-HDMI-Audio)
[    0.242743] ACPI: Added _OSI(Linux-HPI-Hybrid-Graphics)
[    0.334048] ACPI: 8 ACPI AML tables successfully acquired and loaded
[    0.350068] ACPI: Dynamic OEM Table Load:
[    0.350088] ACPI: SSDT 0xFFFF95B27A97C800 00059C (v01 PmRef  Cpu0Ist  00003000 INTL 20120913)
[    0.352502] ACPI: Dynamic OEM Table Load:
[    0.352519] ACPI: SSDT 0xFFFF95B27A91F400 0003A5 (v01 PmRef  Cpu0Cst  00003001 INTL 20120913)
[    0.358398] ACPI: Dynamic OEM Table Load:
[    0.358413] ACPI: SSDT 0xFFFF95B27A8E6800 00015F (v01 PmRef  ApIst    00003000 INTL 20120913)
[    0.363158] ACPI: Dynamic OEM Table Load:
[    0.363176] ACPI: SSDT 0xFFFF95B27B326900 00008D (v01 PmRef  ApCst    00003000 INTL 20120913)
[    0.375096] ACPI: Interpreter enabled
[    0.375164] ACPI: (supports S0 S4 S5)
[    0.375170] ACPI: Using IOAPIC for interrupt routing
[    0.375305] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.380819] ACPI: Power Resource [P06X] (off)
[    0.384022] ACPI: Power Resource [ID3C] (on)
[    0.388188] ACPI: Power Resource [USBC] (on)
[    0.389774] ACPI: Power Resource [WWPR] (off)
[    0.390860] ACPI: Power Resource [WWPR] (off)
[    0.392519] ACPI: Power Resource [WWPR] (off)
[    0.393518] ACPI: Power Resource [WWPR] (off)
[    0.394590] ACPI: Power Resource [WWPR] (off)
[    0.395781] ACPI: Power Resource [WWPR] (off)
[    0.415603] ACPI: Power Resource [CLK2] (on)
[    0.415764] ACPI: Power Resource [CLK4] (on)
[    0.415920] ACPI: Power Resource [P28P] (off)
[    0.416081] ACPI: Power Resource [P18P] (off)
[    0.416246] ACPI: Power Resource [P12P] (off)
[    0.416406] ACPI: Power Resource [P16P] (off)
[    0.422414] ACPI: Power Resource [CLK3] (on)
[    0.422585] ACPI: Power Resource [CLK4] (on)
[    0.425321] ACPI: Power Resource [CLK2] (on)
[    0.425479] ACPI: Power Resource [CLK1] (on)
[    0.429066] ACPI: Power Resource [CLK0] (on)
[    0.429223] ACPI: Power Resource [CLK1] (on)
[    0.431729] ACPI: Power Resource [CLK5] (off)
[    0.432906] ACPI: Power Resource [P33P] (off)
[    0.433070] ACPI: Power Resource [P65P] (off)
[    0.434282] ACPI Error: No handler for Region [GMMR] (0000000096311e29) [UserDefinedRegion] (20190703/evregion-127)
[    0.434297] ACPI Error: Region UserDefinedRegion (ID=146) has no handler (20190703/exfldio-261)
[    0.434319] No Local Variables are initialized for Method [_STA]
[    0.434322] No Arguments are initialized for method [_STA]
[    0.434327] ACPI Error: Aborting method \_SB.PCI0.I2C6.TCSE._STA due to previous error (AE_NOT_EXIST) (20190703/psparse-529)
[    0.434698] ACPI Error: No handler for Region [GMMR] (0000000096311e29) [UserDefinedRegion] (20190703/evregion-127)
[    0.434708] ACPI Error: Region UserDefinedRegion (ID=146) has no handler (20190703/exfldio-261)
[    0.434723] No Local Variables are initialized for Method [_STA]
[    0.434726] No Arguments are initialized for method [_STA]
[    0.434731] ACPI Error: Aborting method \_SB.PCI0.I2C6.TCS7._STA due to previous error (AE_NOT_EXIST) (20190703/psparse-529)
[    0.457350] ACPI: Power Resource [P28X] (off)
[    0.457520] ACPI: Power Resource [P18X] (off)
[    0.457679] ACPI: Power Resource [P12X] (off)
[    0.457855] ACPI: Power Resource [P28P] (off)
[    0.458019] ACPI: Power Resource [P18P] (off)
[    0.458171] ACPI: Power Resource [P12P] (off)
[    0.458335] ACPI: Power Resource [P19X] (off)
[    0.458519] ACPI: Power Resource [P12A] (off)
[    0.458680] ACPI: Power Resource [P28T] (off)
[    0.458843] ACPI: Power Resource [P18D] (off)
[    0.459014] ACPI: Power Resource [P18T] (off)
[    0.459167] ACPI: Power Resource [P3P3] (off)
[    0.459332] ACPI: Power Resource [P12T] (off)
[    0.459491] ACPI: Power Resource [P28W] (off)
[    0.459654] ACPI: Power Resource [P18W] (off)
[    0.459824] ACPI: Power Resource [P12W] (off)
[    0.459980] ACPI: Power Resource [P33W] (off)
[    0.460148] ACPI: Power Resource [P33X] (off)
[    0.460315] ACPI: Power Resource [P4BW] (off)
[    0.473406] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.473426] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3]
[    0.474721] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug SHPCHotplug PME AER PCIeCapability LTR]
[    0.474778] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
[    0.477298] PCI host bridge to bus 0000:00
[    0.477306] pci_bus 0000:00: root bus resource [io  0x0070-0x0077]
[    0.477312] pci_bus 0000:00: root bus resource [io  0x0000-0x006f window]
[    0.477316] pci_bus 0000:00: root bus resource [io  0x0078-0x0cf7 window]
[    0.477321] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    0.477325] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    0.477329] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff window]
[    0.477332] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000fffff window]
[    0.477336] pci_bus 0000:00: root bus resource [mem 0x20000000-0x201fffff window]
[    0.477340] pci_bus 0000:00: root bus resource [mem 0x7ce00001-0x7ee00000 window]
[    0.477343] pci_bus 0000:00: root bus resource [mem 0x80000000-0xdfffffff window]
[    0.477350] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.477381] pci 0000:00:00.0: [8086:2280] type 00 class 0x060000
[    0.478429] pci 0000:00:02.0: [8086:22b0] type 00 class 0x030000
[    0.478463] pci 0000:00:02.0: reg 0x10: [mem 0x90000000-0x90ffffff 64bit]
[    0.478480] pci 0000:00:02.0: reg 0x18: [mem 0x80000000-0x8fffffff 64bit pref]
[    0.478492] pci 0000:00:02.0: reg 0x20: [io  0xf000-0xf03f]
[    0.478532] pci 0000:00:02.0: BAR 2: assigned to efifb
[    0.479046] pci 0000:00:03.0: [8086:22b8] type 00 class 0x048000
[    0.479072] pci 0000:00:03.0: reg 0x10: [mem 0x91000000-0x913fffff]
[    0.479626] pci 0000:00:0b.0: [8086:22dc] type 00 class 0x118000
[    0.479654] pci 0000:00:0b.0: reg 0x10: [mem 0x91839000-0x91839fff 64bit]
[    0.480296] pci 0000:00:14.0: [8086:22b5] type 00 class 0x0c0330
[    0.480334] pci 0000:00:14.0: reg 0x10: [mem 0x91800000-0x9180ffff 64bit]
[    0.480448] pci 0000:00:14.0: PME# supported from D3hot D3cold
[    0.481022] pci 0000:00:1a.0: [8086:2298] type 00 class 0x108000
[    0.481056] pci 0000:00:1a.0: reg 0x10: [mem 0x91700000-0x917fffff]
[    0.481070] pci 0000:00:1a.0: reg 0x14: [mem 0x91600000-0x916fffff]
[    0.481177] pci 0000:00:1a.0: PME# supported from D0 D3hot
[    0.481788] pci 0000:00:1f.0: [8086:229c] type 00 class 0x060100
[    0.502973] ACPI Error: No handler for Region [GMMR] (0000000096311e29) [UserDefinedRegion] (20190703/evregion-127)
[    0.502990] ACPI Error: Region UserDefinedRegion (ID=146) has no handler (20190703/exfldio-261)
[    0.503010] No Local Variables are initialized for Method [_STA]
[    0.503015] No Arguments are initialized for method [_STA]
[    0.503020] ACPI Error: Aborting method \_SB.PCI0.I2C6.TCSE._STA due to previous error (AE_NOT_EXIST) (20190703/psparse-529)
[    0.503084] ACPI Error: No handler for Region [GMMR] (0000000096311e29) [UserDefinedRegion] (20190703/evregion-127)
[    0.503094] ACPI Error: Region UserDefinedRegion (ID=146) has no handler (20190703/exfldio-261)
[    0.503109] No Local Variables are initialized for Method [_STA]
[    0.503112] No Arguments are initialized for method [_STA]
[    0.503117] ACPI Error: Aborting method \_SB.PCI0.I2C6.TCS7._STA due to previous error (AE_NOT_EXIST) (20190703/psparse-529)
[    0.507515] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.507859] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.508199] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.508537] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.508870] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.509212] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.509544] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.509880] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[    0.527138] SCSI subsystem initialized
[    0.527138] libata version 3.00 loaded.
[    0.527138] pci 0000:00:02.0: vgaarb: setting as boot VGA device
[    0.527138] pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[    0.527138] pci 0000:00:02.0: vgaarb: bridge control possible
[    0.527138] vgaarb: loaded
[    0.527138] ACPI: bus type USB registered
[    0.527138] usbcore: registered new interface driver usbfs
[    0.527138] usbcore: registered new interface driver hub
[    0.527138] usbcore: registered new device driver usb
[    0.781294] pps_core: LinuxPPS API ver. 1 registered
[    0.781298] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.781308] PTP clock support registered
[    0.781388] EDAC MC: Ver: 3.0.0
[    0.781388] Registered efivars operations
[    0.781388] PCI: Using ACPI for IRQ routing
[    0.785072] PCI: pci_cache_line_size set to 64 bytes
[    0.785124] Expanded resource Reserved due to conflict with PCI Bus 0000:00
[    0.785131] e820: reserve RAM buffer [mem 0x0008f000-0x0008ffff]
[    0.785136] e820: reserve RAM buffer [mem 0x0009e000-0x0009ffff]
[    0.785138] e820: reserve RAM buffer [mem 0x79e74000-0x7bffffff]
[    0.785141] e820: reserve RAM buffer [mem 0x7b0b4000-0x7bffffff]
[    0.785473] NetLabel: Initializing
[    0.785476] NetLabel:  domain hash size = 128
[    0.785479] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    0.785523] NetLabel:  unlabeled traffic allowed by default
[    0.787623] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.787634] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[    0.789710] clocksource: Switched to clocksource tsc-early
[    0.834823] VFS: Disk quotas dquot_6.6.0
[    0.834883] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.834965] *** VALIDATE hugetlbfs ***
[    0.835238] AppArmor: AppArmor Filesystem Enabled
[    0.835366] pnp: PnP ACPI init
[    0.835869] system 00:00: [io  0x0680-0x069f] has been reserved
[    0.835875] system 00:00: [io  0x0400-0x047f] could not be reserved
[    0.835880] system 00:00: [io  0x0500-0x05fe] has been reserved
[    0.835900] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.849323] system 00:01: [mem 0x91837000-0x91837fff] has been reserved
[    0.849330] system 00:01: [mem 0x91835000-0x91835fff] has been reserved
[    0.849334] system 00:01: [mem 0x91833000-0x91833fff] has been reserved
[    0.849339] system 00:01: [mem 0x91824000-0x91824fff] has been reserved
[    0.849343] system 00:01: [mem 0x91822000-0x91822fff] has been reserved
[    0.849347] system 00:01: [mem 0x91820000-0x91820fff] has been reserved
[    0.849352] system 00:01: [mem 0x9181e000-0x9181efff] has been reserved
[    0.849356] system 00:01: [mem 0x9181c000-0x9181cfff] has been reserved
[    0.849362] system 00:01: [mem 0x9181a000-0x9181afff] has been reserved
[    0.849366] system 00:01: [mem 0x91818000-0x91818fff] has been reserved
[    0.849371] system 00:01: [mem 0x91831000-0x91831fff] has been reserved
[    0.849375] system 00:01: [mem 0x9182f000-0x9182ffff] has been reserved
[    0.849379] system 00:01: [mem 0x9182d000-0x9182dfff] has been reserved
[    0.849384] system 00:01: [mem 0x9182b000-0x9182bfff] has been reserved
[    0.849388] system 00:01: [mem 0x91829000-0x91829fff] has been reserved
[    0.849393] system 00:01: [mem 0x91827000-0x91827fff] has been reserved
[    0.849397] system 00:01: [mem 0x91825000-0x91825fff] has been reserved
[    0.849417] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.849814] system 00:02: [mem 0xe0000000-0xefffffff] could not be reserved
[    0.849819] system 00:02: [mem 0xfea00000-0xfeafffff] has been reserved
[    0.849825] system 00:02: [mem 0xfed01000-0xfed01fff] has been reserved
[    0.849829] system 00:02: [mem 0xfed03000-0xfed03fff] has been reserved
[    0.849834] system 00:02: [mem 0xfed06000-0xfed06fff] has been reserved
[    0.849838] system 00:02: [mem 0xfed08000-0xfed09fff] has been reserved
[    0.849843] system 00:02: [mem 0xfed80000-0xfedbffff] could not be reserved
[    0.849848] system 00:02: [mem 0xfed1c000-0xfed1cfff] has been reserved
[    0.849860] system 00:02: [mem 0xfee00000-0xfeefffff] could not be reserved
[    0.849874] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.850628] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.853990] pnp: PnP ACPI: found 4 devices
[    0.860717] thermal_sys: Registered thermal governor 'fair_share'
[    0.860720] thermal_sys: Registered thermal governor 'bang_bang'
[    0.860723] thermal_sys: Registered thermal governor 'step_wise'
[    0.860725] thermal_sys: Registered thermal governor 'user_space'
[    0.860726] thermal_sys: Registered thermal governor 'power_allocator'
[    0.865255] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    0.865377] pci_bus 0000:00: resource 4 [io  0x0070-0x0077]
[    0.865384] pci_bus 0000:00: resource 5 [io  0x0000-0x006f window]
[    0.865390] pci_bus 0000:00: resource 6 [io  0x0078-0x0cf7 window]
[    0.865395] pci_bus 0000:00: resource 7 [io  0x0d00-0xffff window]
[    0.865402] pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000bffff window]
[    0.865406] pci_bus 0000:00: resource 9 [mem 0x000c0000-0x000dffff window]
[    0.865411] pci_bus 0000:00: resource 10 [mem 0x000e0000-0x000fffff window]
[    0.865416] pci_bus 0000:00: resource 11 [mem 0x20000000-0x201fffff window]
[    0.865420] pci_bus 0000:00: resource 12 [mem 0x7ce00001-0x7ee00000 window]
[    0.865425] pci_bus 0000:00: resource 13 [mem 0x80000000-0xdfffffff window]
[    0.866178] NET: Registered protocol family 2
[    0.866608] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
[    0.866713] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.866987] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear)
[    0.867197] TCP: Hash tables configured (established 32768 bind 32768)
[    0.867337] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
[    0.867405] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
[    0.867698] NET: Registered protocol family 1
[    0.867714] NET: Registered protocol family 44
[    0.867751] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[    0.868394] PCI: CLS 64 bytes, default 64
[    0.868572] Trying to unpack rootfs image as initramfs...
[    1.275686] Initramfs unpacking failed: Decoding failed
[    1.296396] Freeing initrd memory: 46776K
[    1.296472] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    1.296477] software IO TLB: mapped [mem 0x74176000-0x78176000] (64MB)
[    1.296605] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x14c1baf3789, max_idle_ns: 440795266465 ns
[    1.296642] clocksource: Switched to clocksource tsc
[    1.296878] check: Scanning for low memory corruption every 60 seconds
[    1.304291] Initialise system trusted keyrings
[    1.304326] Key type blacklist registered
[    1.304444] workingset: timestamp_bits=36 max_order=20 bucket_order=0
[    1.309141] zbud: loaded
[    1.310413] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.311054] fuse: init (API version 7.31)
[    1.311463] Platform Keyring initialized
[    1.325521] Key type asymmetric registered
[    1.325525] Asymmetric key parser 'x509' registered
[    1.325587] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[    1.325722] io scheduler mq-deadline registered
[    1.330718] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    1.330977] efifb: probing for efifb
[    1.331026] efifb: showing boot graphics
[    1.333531] efifb: framebuffer at 0x80000000, using 4000k, total 4000k
[    1.333534] efifb: mode is 800x1280x32, linelength=3200, pages=1
[    1.333535] efifb: scrolling: redraw
[    1.333539] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[    1.333721] fbcon: Deferring console take-over
[    1.333724] fb0: EFI VGA frame buffer device
[    1.333757] intel_idle: MWAIT substates: 0x33000020
[    1.333761] intel_idle: v0.4.1 model 0x4C
[    1.334371] intel_idle: lapic_timer_reliable_states 0xffffffff
[    1.334495] ACPI: AC: found native INT33F4 PMIC, not loading
[    1.334692] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[    1.334718] ACPI: Power Button [PWRB]
[    1.334858] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1
[    1.334883] ACPI: Lid Switch [LID0]
[    1.334998] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[    1.335039] ACPI: Power Button [PWRF]
[    1.342998] thermal LNXTHERM:00: registered as thermal_zone0
[    1.343003] ACPI: Thermal Zone [TZ00] (0 C)
[    1.343501] battery: ACPI: Battery: found native INT33F4 PMIC, not loading
[    1.343788] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[    1.364377] serial8250: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[    1.374026] Linux agpgart interface v0.103
[    1.468569] loop: module loaded
[    1.469573] libphy: Fixed MDIO Bus: probed
[    1.469576] tun: Universal TUN/TAP device driver, 1.6
[    1.469943] PPP generic driver version 2.4.2
[    1.470221] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.470231] ehci-pci: EHCI PCI platform driver
[    1.470262] ehci-platform: EHCI generic platform driver
[    1.470340] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.470348] ohci-pci: OHCI PCI platform driver
[    1.470372] ohci-platform: OHCI generic platform driver
[    1.470401] uhci_hcd: USB Universal Host Controller Interface driver
[    1.470932] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    1.470950] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[    1.472109] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x0000000081509810
[    1.472126] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[    1.472593] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.03
[    1.472598] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.472605] usb usb1: Product: xHCI Host Controller
[    1.472609] usb usb1: Manufacturer: Linux 5.3.0-46-generic xhci-hcd
[    1.472612] usb usb1: SerialNumber: 0000:00:14.0
[    1.473115] hub 1-0:1.0: USB hub found
[    1.473152] hub 1-0:1.0: 7 ports detected
[    1.475313] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    1.475325] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[    1.475338] xhci_hcd 0000:00:14.0: Host supports USB 3.0 SuperSpeed
[    1.475481] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.03
[    1.475487] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.475490] usb usb2: Product: xHCI Host Controller
[    1.475493] usb usb2: Manufacturer: Linux 5.3.0-46-generic xhci-hcd
[    1.475498] usb usb2: SerialNumber: 0000:00:14.0
[    1.475957] hub 2-0:1.0: USB hub found
[    1.475992] hub 2-0:1.0: 6 ports detected
[    1.478134] i8042: PNP: No PS/2 controller found.
[    1.478854] mousedev: PS/2 mouse device common for all mice
[    1.480391] rtc_cmos 00:03: registered as rtc0
[    1.480447] rtc_cmos 00:03: alarms up to one month, y3k, 242 bytes nvram
[    1.480468] i2c /dev entries driver
[    1.481458] device-mapper: uevent: version 1.0.3
[    1.481907] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com
[    1.481995] platform eisa.0: Probing EISA bus 0
[    1.482001] platform eisa.0: EISA: Cannot allocate resource for mainboard
[    1.482006] platform eisa.0: Cannot allocate resource for EISA slot 1
[    1.482009] platform eisa.0: Cannot allocate resource for EISA slot 2
[    1.482012] platform eisa.0: Cannot allocate resource for EISA slot 3
[    1.482016] platform eisa.0: Cannot allocate resource for EISA slot 4
[    1.482019] platform eisa.0: Cannot allocate resource for EISA slot 5
[    1.482022] platform eisa.0: Cannot allocate resource for EISA slot 6
[    1.482025] platform eisa.0: Cannot allocate resource for EISA slot 7
[    1.482029] platform eisa.0: Cannot allocate resource for EISA slot 8
[    1.482034] platform eisa.0: EISA: Detected 0 cards
[    1.482044] intel_pstate: Intel P-state driver initializing
[    1.483867] ledtrig-cpu: registered to indicate activity on CPUs
[    1.483873] EFI Variables Facility v0.08 2004-May-17
[    1.529589] NET: Registered protocol family 10
[    1.562903] Segment Routing with IPv6
[    1.562964] NET: Registered protocol family 17
[    1.563924] Key type dns_resolver registered
[    1.565836] RAS: Correctable Errors collector initialized.
[    1.566218] microcode: sig=0x406c4, pf=0x1, revision=0x411
[    1.566624] microcode: Microcode Update Driver: v2.2.
[    1.566647] sched_clock: Marking stable (1565625170, 987237)->(1576471588, -9859181)
[    1.567795] registered taskstats version 1
[    1.567821] Loading compiled-in X.509 certificates
[    1.576531] Loaded X.509 cert 'Build time autogenerated kernel key: 58cc9974d2170f3c76d2e16eeb21349faa3b1809'
[    1.576634] zswap: loaded using pool lzo/zbud
[    1.613697] Key type big_key registered
[    1.613714] Key type trusted registered
[    1.632054] Key type encrypted registered
[    1.632070] AppArmor: AppArmor sha1 policy hashing enabled
[    1.633725] integrity: Loading X.509 certificate: UEFI:db
[    1.633865] integrity: Loaded X.509 cert 'Microsoft Corporation UEFI CA 2011: 13adbf4309bd82709c8cd54f316ed522988a1bd4'
[    1.633868] integrity: Loading X.509 certificate: UEFI:db
[    1.633954] integrity: Loaded X.509 cert 'Microsoft Windows Production PCA 2011: a92902398e16c49778cd90f99e4f9ae17c55af53'
[    1.635091] ima: Allocated hash algorithm: sha1
[    1.684360] No architecture policies found
[    1.684399] evm: Initialising EVM extended attributes:
[    1.684402] evm: security.selinux
[    1.684403] evm: security.SMACK64
[    1.684405] evm: security.SMACK64EXEC
[    1.684406] evm: security.SMACK64TRANSMUTE
[    1.684407] evm: security.SMACK64MMAP
[    1.684408] evm: security.apparmor
[    1.684409] evm: security.ima
[    1.684411] evm: security.capability
[    1.684413] evm: HMAC attrs: 0x1
[    1.715420] i2c_designware 808622C1:06: I2C bus managed by PUNIT
[    1.733474] PM:   Magic number: 0:449:93
[    1.733589] acpi INT8260:00: hash matches
[    1.734076] rtc_cmos 00:03: setting system clock to 2020-04-11T20:04:15 UTC (1586635455)
[    1.811058] usb 1-3: new high-speed USB device number 2 using xhci_hcd
[    1.837036] usb 1-3: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=88.32
[    1.837044] usb 1-3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    1.837048] usb 1-3: Product: USB2.0 Hub
[    1.840496] hub 1-3:1.0: USB hub found
[    1.841973] hub 1-3:1.0: 4 ports detected
[    2.143016] usb 1-3.3: new full-speed USB device number 3 using xhci_hcd
[    2.279752] usb 1-3.3: New USB device found, idVendor=04f3, idProduct=3016, bcdDevice= 0.01
[    2.279758] usb 1-3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.279762] usb 1-3.3: Product: ITE Device(8910)
[    2.279766] usb 1-3.3: Manufacturer: ITE Tech. Inc.
[    2.291618] Freeing unused decrypted memory: 2040K
[    2.293472] Freeing unused kernel image memory: 2676K
[    2.293790] Write protecting the kernel read-only data: 22528k
[    2.295623] Freeing unused kernel image memory: 2008K
[    2.297072] Freeing unused kernel image memory: 1420K
[    2.326430] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    2.326724] x86/mm: Checking user space page tables
[    2.355439] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    2.355446] Run /init as init process
[    2.522460] usb 1-3.1: new high-speed USB device number 4 using xhci_hcd
[    2.545160] usb 1-3.1: New USB device found, idVendor=0bda, idProduct=8153, bcdDevice=30.00
[    2.545166] usb 1-3.1: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[    2.545169] usb 1-3.1: Product: USB 10/100/1000 LAN
[    2.545171] usb 1-3.1: Manufacturer: CMI
[    2.545173] usb 1-3.1: SerialNumber: 000001
[    2.724562] sdhci: Secure Digital Host Controller Interface driver
[    2.724565] sdhci: Copyright(c) Pierre Ossman
[    2.751559] mmc0: SDHCI controller on ACPI [80860F14:00] using ADMA
[    2.767597] axp20x-i2c i2c-INT33F4:00: AXP20x variant AXP288 found
[    2.775141] mmc1: SDHCI controller on ACPI [80860F14:01] using ADMA
[    2.801091] mmc2: SDHCI controller on ACPI [80860F14:02] using ADMA
[    2.821269] mmc1: new high speed SDIO card at address 0001
[    2.822529] axp20x-i2c i2c-INT33F4:00: AXP20X driver loaded
[    2.837563] hidraw: raw HID events driver (C) Jiri Kosina
[    2.844869] mmc0: new HS200 MMC card at address 0001
[    2.900259] usbcore: registered new interface driver usbhid
[    2.900262] usbhid: USB HID core driver
[    2.928156] mmcblk0: mmc0:0001 M52532 29.1 GiB 
[    2.929327] mmcblk0boot0: mmc0:0001 M52532 partition 1 4.00 MiB
[    2.929988] mmcblk0boot1: mmc0:0001 M52532 partition 2 4.00 MiB
[    2.930159] mmcblk0rpmb: mmc0:0001 M52532 partition 3 4.00 MiB, chardev (241:0)
[    2.934877] hid-generic 0003:04F3:3016.0001: ignoring exceeding usage max
[    2.936434] input: ITE Tech. Inc. ITE Device(8910) Keyboard as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3.3/1-3.3:1.0/0003:04F3:3016.0001/input/input3
[    2.936678] input: ITE Tech. Inc. ITE Device(8910) Consumer Control as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3.3/1-3.3:1.0/0003:04F3:3016.0001/input/input4
[    2.937071] input: ITE Tech. Inc. ITE Device(8910) Wireless Radio Control as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3.3/1-3.3:1.0/0003:04F3:3016.0001/input/input5
[    2.937453] input: ITE Tech. Inc. ITE Device(8910) System Control as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3.3/1-3.3:1.0/0003:04F3:3016.0001/input/input6
[    2.937639] input: ITE Tech. Inc. ITE Device(8910) as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3.3/1-3.3:1.0/0003:04F3:3016.0001/input/input7
[    2.937988] hid-generic 0003:04F3:3016.0001: input,hiddev0,hidraw0: USB HID v1.10 Keyboard [ITE Tech. Inc. ITE Device(8910)] on usb-0000:00:14.0-3.3/input0
[    2.938767] input: ITE Tech. Inc. ITE Device(8910) Mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3.3/1-3.3:1.1/0003:04F3:3016.0002/input/input8
[    2.939349] input: ITE Tech. Inc. ITE Device(8910) Touchpad as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3.3/1-3.3:1.1/0003:04F3:3016.0002/input/input9
[    2.940103] hid-generic 0003:04F3:3016.0002: input,hiddev1,hidraw1: USB HID v1.10 Mouse [ITE Tech. Inc. ITE Device(8910)] on usb-0000:00:14.0-3.3/input1
[    2.960840]  mmcblk0: p1 p2
[    3.205441] mmc2: new ultra high speed SDR104 SDHC card at address 0001
[    3.206337] mmcblk2: mmc2:0001 EB1QT 29.8 GiB 
[    3.207950]  mmcblk2: p1
[    3.209870] fbcon: Taking over console
[    3.210047] Console: switching to colour frame buffer device 100x80
[    3.219924] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    3.674574] systemd[1]: Inserted module 'autofs4'
[    3.726780] systemd[1]: systemd 242 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=hybrid)
[    3.747770] systemd[1]: Detected architecture x86-64.
[    3.753927] systemd[1]: Set hostname to <jean-Switch-One-SW1-011>.
[    3.755760] systemd[1]: Failed to bump fs.file-max, ignoring: Invalid argument
[    4.010261] systemd[1]: /lib/systemd/system/dbus.socket:4: ListenStream= references a path below legacy directory /var/run/, updating /var/run/dbus/system_bus_socket → /run/dbus/system_bus_socket; please update the unit file accordingly.
[    4.164096] systemd[1]: Listening on fsck to fsckd communication Socket.
[    4.166885] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[    4.167588] systemd[1]: Created slice User and Session Slice.
[    4.167625] systemd[1]: Reached target Slices.
[    4.167985] systemd[1]: Listening on Syslog Socket.
[    4.214211] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro
[    4.237738] lp: driver loaded but no devices found
[    4.283535] ppdev: user-space parallel port driver
[    4.426475] Adding 1392448k swap on /swapfile.  Priority:-2 extents:5 across:1425216k SSFS
[    5.297234] systemd-journald[331]: Received request to flush runtime journal from PID 1
[    5.579780] 8086228A:00: ttyS4 at MMIO 0x91821000 (irq = 39, base_baud = 2764800) is a 16550A
[    5.580303] serial serial0: tty port ttyS4 registered
[    5.589445] 8086228A:01: ttyS5 at MMIO 0x9181f000 (irq = 40, base_baud = 2764800) is a 16550A
[    5.626935] dw_dmac INTL9C60:00: DesignWare DMA Controller, 8 channels
[    5.653478] Goodix-TS i2c-GDIX1001:00: i2c-GDIX1001:00 supply AVDD28 not found, using dummy regulator
[    5.653517] Goodix-TS i2c-GDIX1001:00: i2c-GDIX1001:00 supply VDDIO not found, using dummy regulator
[    5.657667] Goodix-TS i2c-GDIX1001:00: ID 9271, version: 1050
[    5.662683] input: Goodix Capacitive TouchScreen as /devices/pci0000:00/808622C1:05/i2c-4/i2c-GDIX1001:00/input/input10
[    5.667002] dw_dmac INTL9C60:01: DesignWare DMA Controller, 8 channels
[    5.789602] Bluetooth: Core ver 2.22
[    5.789645] NET: Registered protocol family 31
[    5.789647] Bluetooth: HCI device and connection manager initialized
[    5.789656] Bluetooth: HCI socket layer initialized
[    5.789660] Bluetooth: L2CAP socket layer initialized
[    5.789670] Bluetooth: SCO socket layer initialized
[    5.892020] proc_thermal 0000:00:0b.0: enabling device (0000 -> 0002)
[    5.892802] Bluetooth: HCI UART driver ver 2.3
[    5.892807] Bluetooth: HCI UART protocol H4 registered
[    5.892808] Bluetooth: HCI UART protocol BCSP registered
[    5.892840] Bluetooth: HCI UART protocol LL registered
[    5.892842] Bluetooth: HCI UART protocol ATH3K registered
[    5.892887] Bluetooth: HCI UART protocol Three-wire (H5) registered
[    5.892990] Bluetooth: HCI UART protocol Intel registered
[    5.893173] Bluetooth: HCI UART protocol Broadcom registered
[    5.893198] Bluetooth: HCI UART protocol QCA registered
[    5.893200] Bluetooth: HCI UART protocol AG6XX registered
[    5.893221] Bluetooth: HCI UART protocol Marvell registered
[    5.904836] proc_thermal 0000:00:0b.0: Creating sysfs group for PROC_THERMAL_PCI
[    5.960518] axp288_extcon axp288_extcon: controlling USB role based on Vbus presence
[    6.023381] usbcore: registered new interface driver r8152
[    6.051685] usbcore: registered new interface driver cdc_ether
[    6.106772] usb 1-3.1: reset high-speed USB device number 4 using xhci_hcd
[    6.167220] r8152 1-3.1:1.0 eth0: v1.09.11
[    6.212151] input: ITE Tech. Inc. ITE Device(8910) Touchpad as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3.3/1-3.3:1.1/0003:04F3:3016.0002/input/input12
[    6.212757] hid-multitouch 0003:04F3:3016.0002: input,hiddev1,hidraw1: USB HID v1.10 Mouse [ITE Tech. Inc. ITE Device(8910)] on usb-0000:00:14.0-3.3/input1
[    6.229428] cryptd: max_cpu_qlen set to 1000
[    6.232708] axp288_fuel_gauge axp288_fuel_gauge: HW IRQ 16 -> VIRQ 137
[    6.236399] acer_wmi: Acer Laptop ACPI-WMI Extras
[    6.236466] acer_wmi: No WMID device detection method found
[    6.256950] axp288_fuel_gauge axp288_fuel_gauge: HW IRQ 17 -> VIRQ 138
[    6.310660] axp288_fuel_gauge axp288_fuel_gauge: HW IRQ 18 -> VIRQ 139
[    6.334725] axp288_fuel_gauge axp288_fuel_gauge: HW IRQ 19 -> VIRQ 140
[    6.384891] axp288_fuel_gauge axp288_fuel_gauge: HW IRQ 24 -> VIRQ 145
[    6.414897] SSE version of gcm_enc/dec engaged.
[    6.425055] axp288_fuel_gauge axp288_fuel_gauge: HW IRQ 25 -> VIRQ 146
[    6.449580] i915 0000:00:02.0: Disabling error capture for VT-d workaround
[    6.449635] checking generic (80000000 3e8000) vs hw (80000000 10000000)
[    6.449638] fb0: switching to inteldrmfb from EFI VGA
[    6.449920] Console: switching to colour dummy device 80x25
[    6.450031] i915 0000:00:02.0: vgaarb: deactivate vga console
[    6.450274] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    6.450276] [drm] Driver supports precise vblank timestamp query.
[    6.466260] intel_sst_acpi 808622A8:00: LPE base: 0x91400000 size:0x200000
[    6.466265] intel_sst_acpi 808622A8:00: IRAM base: 0x914c0000
[    6.466311] intel_sst_acpi 808622A8:00: DRAM base: 0x91500000
[    6.466322] intel_sst_acpi 808622A8:00: SHIM base: 0x91540000
[    6.466333] intel_sst_acpi 808622A8:00: Mailbox base: 0x91544000
[    6.466342] intel_sst_acpi 808622A8:00: DDR base: 0x20000000
[    6.481692] intel_sst_acpi 808622A8:00: Got drv data max stream 25
[    6.504854] i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=io+mem:owns=io+mem
[    6.541377] Bluetooth: hci0: RTL: rtl: examining hci_ver=06 hci_rev=000b lmp_ver=06 lmp_subver=8723

[    6.545636] Bluetooth: hci0: RTL: rom_version status=0 version=1

[    6.545645] Bluetooth: hci0: RTL: rtl: loading rtl_bt/rtl8723bs_fw.bin

[    6.558478] Bluetooth: hci0: RTL: rtl: loading rtl_bt/rtl8723bs_config-OBDA8723.bin

[    6.584047] Bluetooth: hci0: RTL: cfg_sz 64, total sz 24508

[    6.664787] [drm] Initialized i915 1.6.0 20190619 for 0000:00:02.0 on minor 0
[    6.690210] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[    6.697968] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input13
[    6.698412] [drm] HDaudio controller not detected, using LPE audio instead
[    7.025374] fbcon: i915drmfb (fb0) is primary device
[    7.025527] Console: switching to colour frame buffer device 100x80
[    7.025580] i915 0000:00:02.0: fb0: i915drmfb frame buffer device
[    7.320879] input: gpio-keys as /devices/platform/gpio-keys.0.auto/input/input14
[    7.329794] input: gpio-keys as /devices/platform/gpio-keys.1.auto/input/input15
[    7.482188] intel_rapl_common: Found RAPL domain package
[    7.482193] intel_rapl_common: Found RAPL domain core
[    7.598232] r8152 1-3.1:1.0 enx70886b85783a: renamed from eth0
[    7.684319] bytcr_rt5651 bytcr_rt5651: quirk IN2_MAP enabled
[    7.684325] bytcr_rt5651 bytcr_rt5651: quirk realtek,jack-detect-source 1
[    7.684328] bytcr_rt5651 bytcr_rt5651: quirk realtek,over-current-threshold-microamp 2000
[    7.684330] bytcr_rt5651 bytcr_rt5651: quirk realtek,over-current-scale-factor 1
[    7.684333] bytcr_rt5651 bytcr_rt5651: quirk MCLK_EN enabled
[    7.710852] bytcr_rt5651 bytcr_rt5651: snd-soc-dummy-dai <-> media-cpu-dai mapping ok
[    7.711374] bytcr_rt5651 bytcr_rt5651: snd-soc-dummy-dai <-> deepbuffer-cpu-dai mapping ok
[    7.714254] [drm:mipi_exec_pmic [i915]] *ERROR* Your hardware requires CONFIG_PMIC_OPREGION and it is not set
[    7.731434] bytcr_rt5651 bytcr_rt5651: rt5651-aif1 <-> ssp2-port mapping ok
[    7.733960] input: bytcr-rt5651 Headset as /devices/pci0000:00/808622A8:00/bytcr_rt5651/sound/card0/input17
[    7.736179] input: Intel HDMI/DP LPE Audio HDMI/DP,pcm=0 as /devices/pci0000:00/0000:00:02.0/hdmi-lpe-audio/sound/card1/input16
[    7.736341] input: Intel HDMI/DP LPE Audio HDMI/DP,pcm=1 as /devices/pci0000:00/0000:00:02.0/hdmi-lpe-audio/sound/card1/input18
[    7.736492] input: Intel HDMI/DP LPE Audio HDMI/DP,pcm=2 as /devices/pci0000:00/0000:00:02.0/hdmi-lpe-audio/sound/card1/input19
[    8.822792] audit: type=1400 audit(1586635462.587:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-senddoc" pid=733 comm="apparmor_parser"
[    8.825237] audit: type=1400 audit(1586635462.587:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-xpdfimport" pid=729 comm="apparmor_parser"
[    8.842121] audit: type=1400 audit(1586635462.603:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/sbin/dhclient" pid=731 comm="apparmor_parser"
[    8.842136] audit: type=1400 audit(1586635462.603:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=731 comm="apparmor_parser"
[    8.842144] audit: type=1400 audit(1586635462.603:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=731 comm="apparmor_parser"
[    8.842151] audit: type=1400 audit(1586635462.603:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=731 comm="apparmor_parser"
[    8.847107] audit: type=1400 audit(1586635462.611:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/cups-browsed" pid=736 comm="apparmor_parser"
[    8.855485] audit: type=1400 audit(1586635462.619:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-oopslash" pid=738 comm="apparmor_parser"
[    8.871669] audit: type=1400 audit(1586635462.635:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=737 comm="apparmor_parser"
[    8.871682] audit: type=1400 audit(1586635462.635:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=737 comm="apparmor_parser"
[   12.573876] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   12.573882] Bluetooth: BNEP filters: protocol multicast
[   12.573892] Bluetooth: BNEP socket layer initialized
[   14.100144] IPv6: ADDRCONF(NETDEV_CHANGE): enx70886b85783a: link becomes ready
[   14.100538] r8152 1-3.1:1.0 enx70886b85783a: carrier on
[   15.682898] intel_sst_acpi 808622A8:00: FW Version 01.0b.02.02
[   15.686861] debugfs: File 'SSP2-Codec' in directory 'Audio Port' already present!
[   15.791480] debugfs: File 'SSP2-Codec' in directory 'Audio Port' already present!
[   24.385763] rfkill: input handler disabled
[   79.079301] rfkill: input handler enabled
[   79.674585] debugfs: File 'SSP2-Codec' in directory 'Audio Port' already present!
[   80.189967] debugfs: File 'SSP2-Codec' in directory 'Audio Port' already present!
[   80.357105] Bluetooth: RFCOMM TTY layer initialized
[   80.357121] Bluetooth: RFCOMM socket layer initialized
[   80.357137] Bluetooth: RFCOMM ver 1.11
[   83.571919] [drm:mipi_exec_pmic [i915]] *ERROR* Your hardware requires CONFIG_PMIC_OPREGION and it is not set
[   93.557765] rfkill: input handler disabled
[  131.104704] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[  131.104716] Bluetooth: HIDP socket layer initialized
[  131.109790] hid-generic 0005:099A:0500.0003: unknown main item tag 0x0
[  131.110190] input: Bluetooth Mouse as /devices/pci0000:00/8086228A:00/serial0/serial0-0/bluetooth/hci0/hci0:1/0005:099A:0500.0003/input/input20
[  131.115535] hid-generic 0005:099A:0500.0003: input,hidraw2: BLUETOOTH HID v1.1b Mouse [Bluetooth Mouse] on c0:21:0d:e5:29:26
[  227.805405] kauditd_printk_skb: 37 callbacks suppressed
[  227.805409] audit: type=1400 audit(1586635681.271:49): apparmor="DENIED" operation="capable" profile="/snap/core/8935/usr/lib/snapd/snap-confine" pid=2662 comm="snap-confine" capability=4  capname="fsetid"
[  237.912978] audit: type=1107 audit(1586635691.379:50): pid=786 uid=103 auid=4294967295 ses=4294967295 msg='apparmor="DENIED" operation="dbus_method_call"  bus="system" path="/" interface="org.freedesktop.DBus.ObjectManager" member="GetManagedObjects" mask="send" name="org.bluez" pid=2662 label="snap.chromium.chromium" peer_pid=784 peer_label="unconfined"
                exe="/usr/bin/dbus-daemon" sauid=103 hostname=? addr=? terminal=?'
[  247.933801] audit: type=1400 audit(1586635701.400:51): apparmor="DENIED" operation="open" profile="snap.chromium.chromium" name="/run/udev/data/+sdio:mmc1:0001:1" pid=2662 comm="ThreadPoolForeg" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[  247.939695] audit: type=1400 audit(1586635701.408:52): apparmor="DENIED" operation="open" profile="snap.chromium.chromium" name="/run/udev/data/+serial:serial0-0" pid=2662 comm="ThreadPoolForeg" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[  248.355227] audit: type=1400 audit(1586635701.824:53): apparmor="DENIED" operation="open" profile="snap.chromium.chromium" name="/run/udev/data/b179:24" pid=2662 comm="ThreadPoolForeg" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[  248.357654] audit: type=1400 audit(1586635701.824:54): apparmor="DENIED" operation="open" profile="snap.chromium.chromium" name="/run/udev/data/b179:0" pid=2662 comm="ThreadPoolForeg" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[  248.359496] audit: type=1400 audit(1586635701.828:55): apparmor="DENIED" operation="open" profile="snap.chromium.chromium" name="/run/udev/data/b179:8" pid=2662 comm="ThreadPoolForeg" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[  248.362185] audit: type=1400 audit(1586635701.828:56): apparmor="DENIED" operation="open" profile="snap.chromium.chromium" name="/run/udev/data/b179:1" pid=2662 comm="ThreadPoolForeg" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[  248.365954] audit: type=1400 audit(1586635701.832:57): apparmor="DENIED" operation="open" profile="snap.chromium.chromium" name="/run/udev/data/b179:16" pid=2662 comm="ThreadPoolForeg" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[  248.368321] audit: type=1400 audit(1586635701.836:58): apparmor="DENIED" operation="open" profile="snap.chromium.chromium" name="/run/udev/data/b179:25" pid=2662 comm="ThreadPoolForeg" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[  248.370327] audit: type=1400 audit(1586635701.836:59): apparmor="DENIED" operation="open" profile="snap.chromium.chromium" name="/run/udev/data/b179:2" pid=2662 comm="ThreadPoolForeg" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0

jean@jean-Switch-One-SW1-011:~$

ls -R /sys/bus/sdio/devices/ après redémarrage

jean@jean-Switch-One-SW1-011:~$ ls -R /sys/bus/sdio/devices/
/sys/bus/sdio/devices/:
mmc1:0001:1

Nuliel · Le 11/04/2020, à 21:36

Ok, donc effectivement le machin est bien sur un port SDIO (port SD "amélioré").
Il est vu par le système, donc il devrait normalement fonctionner. Tu peux donner

lsmod | sort

pour vérifier que le pilote rtl8723bs n'est pas chargé, et si non tu peux passer

sudo modprobe rtl8723bs

Barrab · Le 11/04/2020, à 22:01

8250_dw                20480  0
ac97_bus               16384  1 snd_soc_core
acpi_pad              184320  0
acpi_thermal_rel       16384  1 int3400_thermal
aesni_intel           372736  2
aes_x86_64             20480  1 aesni_intel
autofs4                45056  2
axp20x                 32768  1 axp20x_i2c
axp20x_i2c             16384  0
axp20x_pek             16384  0
axp288_adc             16384  0
axp288_charger         24576  0
axp288_fuel_gauge      28672  0
bluetooth             581632  37 btrtl,hidp,btqca,btintel,hci_uart,btbcm,bnep,rfcomm
bnep                   24576  2
btbcm                  16384  1 hci_uart
btintel                24576  1 hci_uart
btqca                  20480  1 hci_uart
btrtl                  20480  1 hci_uart
cdc_ether              20480  0
cmac                   16384  1
coretemp               20480  0
crc32_pclmul           16384  0
crct10dif_pclmul       16384  1
cryptd                 24576  2 crypto_simd,ghash_clmulni_intel
crypto_simd            16384  1 aesni_intel
drm                   491520  7 drm_kms_helper,i915
drm_kms_helper        184320  1 i915
dw_dmac                16384  8
dw_dmac_core           28672  1 dw_dmac
ecc                    28672  1 ecdh_generic
ecdh_generic           16384  2 bluetooth
extcon_axp288          20480  0
fb_sys_fops            16384  1 drm_kms_helper
ghash_clmulni_intel    16384  0
glue_helper            16384  1 aesni_intel
goodix                 24576  0
gpio_keys              20480  0
hci_uart              126976  0
hid                   131072  4 hidp,usbhid,hid_multitouch,hid_generic
hid_generic            16384  0
hid_multitouch         28672  0
hidp                   28672  1
i2c_algo_bit           16384  1 i915
i915                 1949696  13
industrialio           77824  5 axp288_adc,industrialio_triggered_buffer,kfifo_buf,axp288_fuel_gauge,kxcjk_1013
industrialio_triggered_buffer    16384  1 kxcjk_1013
input_leds             16384  0
int3400_thermal        20480  0
int3403_thermal        16384  0
int340x_thermal_zone    16384  2 int3403_thermal,processor_thermal_device
intel_atomisp2_pm      16384  0
intel_cht_int33fe      16384  0
intel_cstate           20480  0
intel_int0002_vgpio    16384  1
intel_powerclamp       20480  0
intel_rapl_common      24576  2 intel_rapl_msr,processor_thermal_device
intel_rapl_msr         20480  0
intel_soc_dts_iosf     20480  1 processor_thermal_device
intel_xhci_usb_role_switch    16384  1
ip_tables              32768  0
irqbypass              16384  1 kvm
joydev                 28672  0
kfifo_buf              16384  1 industrialio_triggered_buffer
kvm                   659456  1 kvm_intel
kvm_intel             278528  0
kxcjk_1013             28672  0
lp                     20480  0
lpc_ich                24576  0
mac_hid                16384  0
mei                   110592  3 mei_hdcp,mei_txe
mei_hdcp               24576  0
mei_txe                28672  1
mii                    20480  2 usbnet,r8152
mmc_block              49152  5
Module                  Size  Used by
nls_iso8859_1          16384  1
parport                53248  3 parport_pc,lp,ppdev
parport_pc             40960  0
ppdev                  24576  0
processor_thermal_device    20480  0
punit_atom_debug       16384  0
r8152                  65536  0
rfcomm                 81920  4
roles                  16384  2 extcon_axp288,intel_xhci_usb_role_switch
sch_fq_codel           20480  2
sdhci                  57344  1 sdhci_acpi
sdhci_acpi             24576  0
snd                    90112  16 snd_seq,snd_seq_device,snd_soc_sst_bytcr_rt5651,snd_timer,snd_compress,snd_hdmi_lpe_audio,snd_soc_sst_atom_hifi2_platform,snd_soc_core,snd_pcm,snd_rawmidi
snd_compress           24576  1 snd_soc_core
snd_hdmi_lpe_audio     28672  1
snd_intel_sst_acpi     20480  1
snd_intel_sst_core     61440  1 snd_intel_sst_acpi
snd_pcm               106496  7 snd_soc_rt5651,snd_sof,snd_soc_sst_bytcr_rt5651,snd_hdmi_lpe_audio,snd_soc_sst_atom_hifi2_platform,snd_soc_core,snd_pcm_dmaengine
snd_pcm_dmaengine      16384  1 snd_soc_core
snd_rawmidi            36864  1 snd_seq_midi
snd_seq                69632  2 snd_seq_midi,snd_seq_midi_event
snd_seq_device         16384  3 snd_seq,snd_seq_midi,snd_rawmidi
snd_seq_midi           20480  0
snd_seq_midi_event     16384  1 snd_seq_midi
snd_soc_acpi           16384  4 snd_soc_acpi_intel_match,sof_acpi_dev,snd_soc_sst_bytcr_rt5651,snd_intel_sst_acpi
snd_soc_acpi_intel_match    32768  2 sof_acpi_dev,snd_intel_sst_acpi
snd_soc_core          241664  4 snd_soc_rt5651,snd_sof,snd_soc_sst_bytcr_rt5651,snd_soc_sst_atom_hifi2_platform
snd_soc_rl6231         20480  1 snd_soc_rt5651
snd_soc_rt5651        102400  1
snd_soc_sst_atom_hifi2_platform   110592  2 snd_intel_sst_core
snd_soc_sst_bytcr_rt5651    36864  2
snd_sof               102400  3 sof_acpi_dev,snd_sof_intel_byt,snd_sof_intel_ipc
snd_sof_intel_byt      24576  1 sof_acpi_dev
snd_sof_intel_ipc      20480  1 snd_sof_intel_byt
snd_sof_xtensa_dsp     16384  1 sof_acpi_dev
snd_timer              36864  2 snd_seq,snd_pcm
soc_button_array       20480  0
sof_acpi_dev           20480  0
soundcore              16384  1 snd
sparse_keymap          16384  0
spi_pxa2xx_platform    32768  0
syscopyarea            16384  1 drm_kms_helper
sysfillrect            16384  1 drm_kms_helper
sysimgblt              16384  1 drm_kms_helper
usbhid                 57344  0
usbnet                 45056  1 cdc_ether
video                  49152  1 i915
wmi                    32768  1 wmi_bmof
wmi_bmof               16384  0
x_tables               40960  1 ip_tables
jean@jean-Switch-One-SW1-011:~$

jean@jean-Switch-One-SW1-011:~$ sudo modprobe rtl8723bs
[sudo] Mot de passe de jean : 
modprobe: FATAL: Module rtl8723bs not found in directory /lib/modules/5.3.0-46-generic

NicoApi73 · Le 11/04/2020, à 23:25

Bonsoir,

Essaie dans ce cas :

sudo modprobe r8723bs

(basé sur un fil donné par xubu)

Barrab · Le 11/04/2020, à 23:31

Voici le résultat

ean@jean-Switch-One-SW1-011:~$ sudo modprobe r8723bs
jean@jean-Switch-One-SW1-011:~$

NicoApi73 · Le 11/04/2020, à 23:34

ok, le module est chargé.

Donne :

lsmod | sort

puis :

sudo lshw -class network

et plus large :

sudo lshw

(La dernière commande englobe la précédente. C'est au cas où je ne trouve pas l'information que je cherche)

Barrab · Le 11/04/2020, à 23:59

lsmod | sort

jean@jean-Switch-One-SW1-011:~$ lsmod | sort
8250_dw                20480  0
ac97_bus               16384  1 snd_soc_core
acpi_pad              184320  0
acpi_thermal_rel       16384  1 int3400_thermal
aesni_intel           372736  2
aes_x86_64             20480  1 aesni_intel
autofs4                45056  2
axp20x                 32768  1 axp20x_i2c
axp20x_i2c             16384  0
axp20x_pek             16384  0
axp288_adc             16384  0
axp288_charger         24576  0
axp288_fuel_gauge      28672  0
bluetooth             581632  37 btrtl,hidp,btqca,btintel,hci_uart,btbcm,bnep,rfcomm
bnep                   24576  2
btbcm                  16384  1 hci_uart
btintel                24576  1 hci_uart
btqca                  20480  1 hci_uart
btrtl                  20480  1 hci_uart
cdc_ether              20480  0
cfg80211              712704  1 r8723bs
cmac                   16384  1
coretemp               20480  0
crc32_pclmul           16384  0
crct10dif_pclmul       16384  1
cryptd                 24576  2 crypto_simd,ghash_clmulni_intel
crypto_simd            16384  1 aesni_intel
drm                   491520  7 drm_kms_helper,i915
drm_kms_helper        184320  1 i915
dw_dmac                16384  8
dw_dmac_core           28672  1 dw_dmac
ecc                    28672  1 ecdh_generic
ecdh_generic           16384  2 bluetooth
extcon_axp288          20480  0
fb_sys_fops            16384  1 drm_kms_helper
ghash_clmulni_intel    16384  0
glue_helper            16384  1 aesni_intel
goodix                 24576  0
gpio_keys              20480  0
hci_uart              126976  0
hid                   131072  4 hidp,usbhid,hid_multitouch,hid_generic
hid_generic            16384  0
hid_multitouch         28672  0
hidp                   28672  1
i2c_algo_bit           16384  1 i915
i915                 1949696  13
industrialio           77824  5 axp288_adc,industrialio_triggered_buffer,kfifo_buf,axp288_fuel_gauge,kxcjk_1013
industrialio_triggered_buffer    16384  1 kxcjk_1013
input_leds             16384  0
int3400_thermal        20480  0
int3403_thermal        16384  0
int340x_thermal_zone    16384  2 int3403_thermal,processor_thermal_device
intel_atomisp2_pm      16384  0
intel_cht_int33fe      16384  0
intel_cstate           20480  0
intel_int0002_vgpio    16384  1
intel_powerclamp       20480  0
intel_rapl_common      24576  2 intel_rapl_msr,processor_thermal_device
intel_rapl_msr         20480  0
intel_soc_dts_iosf     20480  1 processor_thermal_device
intel_xhci_usb_role_switch    16384  1
ip_tables              32768  0
irqbypass              16384  1 kvm
joydev                 28672  0
kfifo_buf              16384  1 industrialio_triggered_buffer
kvm                   659456  1 kvm_intel
kvm_intel             278528  0
kxcjk_1013             28672  0
lp                     20480  0
lpc_ich                24576  0
mac_hid                16384  0
mei                   110592  3 mei_hdcp,mei_txe
mei_hdcp               24576  0
mei_txe                28672  1
mii                    20480  2 usbnet,r8152
mmc_block              49152  5
Module                  Size  Used by
nls_iso8859_1          16384  1
parport                53248  3 parport_pc,lp,ppdev
parport_pc             40960  0
ppdev                  24576  0
processor_thermal_device    20480  0
punit_atom_debug       16384  0
r8152                  65536  0
r8723bs               610304  0
rfcomm                 81920  4
roles                  16384  2 extcon_axp288,intel_xhci_usb_role_switch
sch_fq_codel           20480  2
sdhci                  57344  1 sdhci_acpi
sdhci_acpi             24576  0
snd                    90112  16 snd_seq,snd_seq_device,snd_soc_sst_bytcr_rt5651,snd_timer,snd_compress,snd_hdmi_lpe_audio,snd_soc_sst_atom_hifi2_platform,snd_soc_core,snd_pcm,snd_rawmidi
snd_compress           24576  1 snd_soc_core
snd_hdmi_lpe_audio     28672  1
snd_intel_sst_acpi     20480  1
snd_intel_sst_core     61440  1 snd_intel_sst_acpi
snd_pcm               106496  7 snd_soc_rt5651,snd_sof,snd_soc_sst_bytcr_rt5651,snd_hdmi_lpe_audio,snd_soc_sst_atom_hifi2_platform,snd_soc_core,snd_pcm_dmaengine
snd_pcm_dmaengine      16384  1 snd_soc_core
snd_rawmidi            36864  1 snd_seq_midi
snd_seq                69632  2 snd_seq_midi,snd_seq_midi_event
snd_seq_device         16384  3 snd_seq,snd_seq_midi,snd_rawmidi
snd_seq_midi           20480  0
snd_seq_midi_event     16384  1 snd_seq_midi
snd_soc_acpi           16384  4 snd_soc_acpi_intel_match,sof_acpi_dev,snd_soc_sst_bytcr_rt5651,snd_intel_sst_acpi
snd_soc_acpi_intel_match    32768  2 sof_acpi_dev,snd_intel_sst_acpi
snd_soc_core          241664  4 snd_soc_rt5651,snd_sof,snd_soc_sst_bytcr_rt5651,snd_soc_sst_atom_hifi2_platform
snd_soc_rl6231         20480  1 snd_soc_rt5651
snd_soc_rt5651        102400  1
snd_soc_sst_atom_hifi2_platform   110592  2 snd_intel_sst_core
snd_soc_sst_bytcr_rt5651    36864  2
snd_sof               102400  3 sof_acpi_dev,snd_sof_intel_byt,snd_sof_intel_ipc
snd_sof_intel_byt      24576  1 sof_acpi_dev
snd_sof_intel_ipc      20480  1 snd_sof_intel_byt
snd_sof_xtensa_dsp     16384  1 sof_acpi_dev
snd_timer              36864  2 snd_seq,snd_pcm
soc_button_array       20480  0
sof_acpi_dev           20480  0
soundcore              16384  1 snd
sparse_keymap          16384  0
spi_pxa2xx_platform    32768  0
syscopyarea            16384  1 drm_kms_helper
sysfillrect            16384  1 drm_kms_helper
sysimgblt              16384  1 drm_kms_helper
usbhid                 57344  0
usbnet                 45056  1 cdc_ether
video                  49152  1 i915
wmi                    32768  1 wmi_bmof
wmi_bmof               16384  0
x_tables               40960  1 ip_tables
jean@jean-Switch-One-SW1-011:~$

sudo lshw -class network

jean@jean-Switch-One-SW1-011:~$ sudo lshw -class network
[sudo] Mot de passe de jean : 
  *-network                 
       description: Ethernet interface
       identifiant matériel: 1
       information bus: usb@1:3.1
       nom logique: enx70886b85783a
       numéro de série: 70:88:6b:85:78:3a
       taille: 100Mbit/s
       capacité: 1Gbit/s
       fonctionnalités: ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
       configuration : autonegotiation=on broadcast=yes driver=r8152 driverversion=v1.09.11 duplex=full ip=192.168.2.63 link=yes multicast=yes port=MII speed=100Mbit/s
jean@jean-Switch-One-SW1-011:~$

sudo lshw

ean@jean-Switch-One-SW1-011:~$ sudo lshw
jean-switch-one-sw1-011     
    description: Ordinateur de Bureau
    produit: Switch One SW1-011 (Default string)
    fabricant: Acer
    version: 1.0
    numéro de série: NTLCSAA00372179AF27200
    bits: 64 bits
    fonctionnalités: smbios-3.0.0 dmi-3.0.0 smp vsyscall32
    configuration : boot=normal chassis=desktop family=CHT-CR sku=Default string uuid=522D3895-79D6-4F51-A3C1-C0210DDF0EA6
  *-core
       description: Carte mère
       produit: Okinawa
       fabricant: Acer
       identifiant matériel: 0
       version: Default string
       numéro de série: NBLCT11007720F00BD7200
       emplacement: Default string
     *-firmware
          description: BIOS
          fabricant: American Megatrends Inc.
          identifiant matériel: 0
          version: 1.09
          date: 01/14/2017
          taille: 64KiB
          capacité: 4MiB
          fonctionnalités: pci upgrade shadowing cdboot bootselect socketedrom edd int13floppy1200 int13floppy720 int13floppy2880 int5printscreen int14serial int17printer acpi usb biosbootspecification uefi
     *-memory
          description: Mémoire Système
          identifiant matériel: 28
          emplacement: Carte mère
          taille: 4GiB
          fonctionnalités: ecc
          configuration : errordetection=multi-bit-ecc
        *-bank:0
             description: DIMM DDR3 1600 MHz (0.6 ns)
             produit: 00000000
             fabricant: Hynix Semiconductor
             identifiant matériel: 0
             numéro de série: 00000000
             emplacement: A1_DIMM0
             taille: 4GiB
             bits: 8 bits
             horloge: 1600MHz (0.6ns)
        *-bank:1
             description: DIMMProject-Id-Version: @(#) $Id$Report-Msgid-Bugs-To: PO-Revision-Date: 2019-07-11 23:21+0000Last-Translator: Lyonel Vincent <Unknown>Language-Team: MIME-Version: 1.0Content-Type: text/plain; charset=UTF-8Content-Transfer-Encoding: 8bitX-Launchpad-Export-Date: 2019-10-10 15:05+0000X-Generator: Launchpad (build af2eefe214bd95389a09b7c956720881bab16807) [vide]
             produit: 00000000
             fabricant: Hynix Semiconductor
             identifiant matériel: 1
             numéro de série: 00000000
             emplacement: A1_DIMM1
     *-cache:0
          description: L1 cache
          identifiant matériel: 32
          emplacement: CPU Internal L1
          taille: 224KiB
          capacité: 224KiB
          fonctionnalités: internal write-back
          configuration : level=1
     *-cache:1
          description: L2 cache
          identifiant matériel: 33
          emplacement: CPU Internal L2
          taille: 2MiB
          capacité: 2MiB
          fonctionnalités: internal write-back unified
          configuration : level=2
     *-cpu
          description: CPU
          produit: Intel(R) Atom(TM) x5-Z8350  CPU @ 1.44GHz
          fabricant: Intel Corp.
          identifiant matériel: 34
          information bus: cpu@0
          version: Intel(R) Atom(TM) x5-Z8350 CPU @ 1.44GHz
          emplacement: SOCKET 0
          taille: 517MHz
          capacité: 2400MHz
          bits: 64 bits
          horloge: 80MHz
          fonctionnalités: lm fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp x86-64 constant_tsc arch_perfmon pebs bts rep_good nopl xtopology tsc_reliable nonstop_tsc cpuid aperfmperf tsc_known_freq pni pclmulqdq dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm sse4_1 sse4_2 movbe popcnt tsc_deadline_timer aes rdrand lahf_lm 3dnowprefetch epb pti ibrs ibpb stibp tpr_shadow vnmi flexpriority ept vpid tsc_adjust smep erms dtherm ida arat md_clear cpufreq
          configuration : cores=4 enabledcores=4 threads=4
     *-pci
          description: Host bridge
          produit: Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series SoC Transaction Register
          fabricant: Intel Corporation
          identifiant matériel: 100
          information bus: pci@0000:00:00.0
          version: 36
          bits: 32 bits
          horloge: 33MHz
          configuration : driver=iosf_mbi_pci
          ressources : irq:0
        *-display
             description: VGA compatible controller
             produit: Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Integrated Graphics Controller
             fabricant: Intel Corporation
             identifiant matériel: 2
             information bus: pci@0000:00:02.0
             version: 36
             bits: 64 bits
             horloge: 33MHz
             fonctionnalités: pm msi vga_controller bus_master cap_list rom
             configuration : driver=i915 latency=0
             ressources : irq:174 mémoire:90000000-90ffffff mémoire:80000000-8fffffff portE/S:f000(taille=64) mémoire:c0000-dffff
        *-multimedia
             description: Multimedia controller
             produit: Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series Imaging Unit
             fabricant: Intel Corporation
             identifiant matériel: 3
             information bus: pci@0000:00:03.0
             version: 36
             bits: 32 bits
             horloge: 33MHz
             fonctionnalités: pm msi cap_list
             configuration : driver=intel_atomisp2_pm latency=0
             ressources : irq:255 mémoire:91000000-913fffff
        *-generic:0
             description: Signal processing controller
             produit: Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series Power Management Controller
             fabricant: Intel Corporation
             identifiant matériel: b
             information bus: pci@0000:00:0b.0
             version: 36
             bits: 64 bits
             horloge: 33MHz
             fonctionnalités: msi pm cap_list
             configuration : driver=proc_thermal latency=0
             ressources : irq:172 mémoire:91839000-91839fff
        *-usb
             description: USB controller
             produit: Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series USB xHCI Controller
             fabricant: Intel Corporation
             identifiant matériel: 14
             information bus: pci@0000:00:14.0
             version: 36
             bits: 64 bits
             horloge: 33MHz
             fonctionnalités: pm msi xhci bus_master cap_list
             configuration : driver=xhci_hcd latency=0
             ressources : irq:119 mémoire:91800000-9180ffff
           *-usbhost:0
                produit: xHCI Host Controller
                fabricant: Linux 5.3.0-46-generic xhci-hcd
                identifiant matériel: 0
                information bus: usb@1
                nom logique: usb1
                version: 5.03
                fonctionnalités: usb-2.00
                configuration : driver=hub slots=7 speed=480Mbit/s
              *-usb
                   description: Concentrateur USB
                   produit: USB2.0 Hub
                   fabricant: Genesys Logic, Inc.
                   identifiant matériel: 3
                   information bus: usb@1:3
                   version: 88.32
                   fonctionnalités: usb-2.00
                   configuration : driver=hub maxpower=100mA slots=4 speed=480Mbit/s
                 *-usb:0
                      description: Périphérique USB générique
                      produit: USB 10/100/1000 LAN
                      fabricant: CMI
                      identifiant matériel: 1
                      information bus: usb@1:3.1
                      version: 30.00
                      numéro de série: 000001
                      fonctionnalités: usb-2.10
                      configuration : driver=r8152 maxpower=200mA speed=480Mbit/s
                 *-usb:1
                      description: Clavier
                      produit: ITE Device(8910)
                      fabricant: ITE Tech. Inc.
                      identifiant matériel: 3
                      information bus: usb@1:3.3
                      version: 0.01
                      fonctionnalités: usb-2.00
                      configuration : driver=usbhid maxpower=100mA speed=12Mbit/s
           *-usbhost:1
                produit: xHCI Host Controller
                fabricant: Linux 5.3.0-46-generic xhci-hcd
                identifiant matériel: 1
                information bus: usb@2
                nom logique: usb2
                version: 5.03
                fonctionnalités: usb-3.00
                configuration : driver=hub slots=6 speed=5000Mbit/s
        *-generic:1
             description: Encryption controller
             produit: Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series Trusted Execution Engine
             fabricant: Intel Corporation
             identifiant matériel: 1a
             information bus: pci@0000:00:1a.0
             version: 36
             bits: 32 bits
             horloge: 33MHz
             fonctionnalités: pm msi bus_master cap_list
             configuration : driver=mei_txe latency=0
             ressources : irq:171 mémoire:91700000-917fffff mémoire:91600000-916fffff
        *-isa
             description: ISA bridge
             produit: Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series PCU
             fabricant: Intel Corporation
             identifiant matériel: 1f
             information bus: pci@0000:00:1f.0
             version: 36
             bits: 32 bits
             horloge: 33MHz
             fonctionnalités: isa bus_master cap_list
             configuration : driver=lpc_ich latency=0
             ressources : irq:0
     *-pnp00:00
          produit: PnP device PNP0c02
          identifiant matériel: 1
          fonctionnalités: pnp
          configuration : driver=system
     *-pnp00:01
          produit: PnP device PNP0c02
          identifiant matériel: 2
          fonctionnalités: pnp
          configuration : driver=system
     *-pnp00:02
          produit: PnP device PNP0c02
          identifiant matériel: 3
          fonctionnalités: pnp
          configuration : driver=system
     *-pnp00:03
          produit: PnP device PNP0b00
          identifiant matériel: 4
          fonctionnalités: pnp
          configuration : driver=rtc_cmos
  *-network
       description: Ethernet interface
       identifiant matériel: 1
       information bus: usb@1:3.1
       nom logique: enx70886b85783a
       numéro de série: 70:88:6b:85:78:3a
       taille: 100Mbit/s
       capacité: 1Gbit/s
       fonctionnalités: ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
       configuration : autonegotiation=on broadcast=yes driver=r8152 driverversion=v1.09.11 duplex=full ip=192.168.2.63 link=yes multicast=yes port=MII speed=100Mbit/s
jean@jean-Switch-One-SW1-011:~$

Barrab · Le 12/04/2020, à 00:01

Merci encore pour tout les efforts que vous déployez pour résoudre ce problème :-)

NicoApi73 · Le 12/04/2020, à 00:01

Il faut attendre le retour de Naziel. Le module est bien chargé mais on ne le voit pas alloué au HW...

NicoApi73 · Le 12/04/2020, à 00:03

A tout hasard, donne le retour de :

dmesg | tail -50

Pour voir si il y a une information exploitable après le modprobe...

Barrab · Le 12/04/2020, à 00:40

dmesg | tail -50

jean@jean-Switch-One-SW1-011:~$ dmesg | tail -50
[   79.674585] debugfs: File 'SSP2-Codec' in directory 'Audio Port' already present!
[   80.189967] debugfs: File 'SSP2-Codec' in directory 'Audio Port' already present!
[   80.357105] Bluetooth: RFCOMM TTY layer initialized
[   80.357121] Bluetooth: RFCOMM socket layer initialized
[   80.357137] Bluetooth: RFCOMM ver 1.11
[   83.571919] [drm:mipi_exec_pmic [i915]] *ERROR* Your hardware requires CONFIG_PMIC_OPREGION and it is not set
[   93.557765] rfkill: input handler disabled
[  131.104704] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[  131.104716] Bluetooth: HIDP socket layer initialized
[  131.109790] hid-generic 0005:099A:0500.0003: unknown main item tag 0x0
[  131.110190] input: Bluetooth Mouse as /devices/pci0000:00/8086228A:00/serial0/serial0-0/bluetooth/hci0/hci0:1/0005:099A:0500.0003/input/input20
[  131.115535] hid-generic 0005:099A:0500.0003: input,hidraw2: BLUETOOTH HID v1.1b Mouse [Bluetooth Mouse] on c0:21:0d:e5:29:26
[  227.805405] kauditd_printk_skb: 37 callbacks suppressed
[  227.805409] audit: type=1400 audit(1586635681.271:49): apparmor="DENIED" operation="capable" profile="/snap/core/8935/usr/lib/snapd/snap-confine" pid=2662 comm="snap-confine" capability=4  capname="fsetid"
[  237.912978] audit: type=1107 audit(1586635691.379:50): pid=786 uid=103 auid=4294967295 ses=4294967295 msg='apparmor="DENIED" operation="dbus_method_call"  bus="system" path="/" interface="org.freedesktop.DBus.ObjectManager" member="GetManagedObjects" mask="send" name="org.bluez" pid=2662 label="snap.chromium.chromium" peer_pid=784 peer_label="unconfined"
                exe="/usr/bin/dbus-daemon" sauid=103 hostname=? addr=? terminal=?'
[  247.933801] audit: type=1400 audit(1586635701.400:51): apparmor="DENIED" operation="open" profile="snap.chromium.chromium" name="/run/udev/data/+sdio:mmc1:0001:1" pid=2662 comm="ThreadPoolForeg" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[  247.939695] audit: type=1400 audit(1586635701.408:52): apparmor="DENIED" operation="open" profile="snap.chromium.chromium" name="/run/udev/data/+serial:serial0-0" pid=2662 comm="ThreadPoolForeg" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[  248.355227] audit: type=1400 audit(1586635701.824:53): apparmor="DENIED" operation="open" profile="snap.chromium.chromium" name="/run/udev/data/b179:24" pid=2662 comm="ThreadPoolForeg" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[  248.357654] audit: type=1400 audit(1586635701.824:54): apparmor="DENIED" operation="open" profile="snap.chromium.chromium" name="/run/udev/data/b179:0" pid=2662 comm="ThreadPoolForeg" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[  248.359496] audit: type=1400 audit(1586635701.828:55): apparmor="DENIED" operation="open" profile="snap.chromium.chromium" name="/run/udev/data/b179:8" pid=2662 comm="ThreadPoolForeg" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[  248.362185] audit: type=1400 audit(1586635701.828:56): apparmor="DENIED" operation="open" profile="snap.chromium.chromium" name="/run/udev/data/b179:1" pid=2662 comm="ThreadPoolForeg" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[  248.365954] audit: type=1400 audit(1586635701.832:57): apparmor="DENIED" operation="open" profile="snap.chromium.chromium" name="/run/udev/data/b179:16" pid=2662 comm="ThreadPoolForeg" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[  248.368321] audit: type=1400 audit(1586635701.836:58): apparmor="DENIED" operation="open" profile="snap.chromium.chromium" name="/run/udev/data/b179:25" pid=2662 comm="ThreadPoolForeg" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[  248.370327] audit: type=1400 audit(1586635701.836:59): apparmor="DENIED" operation="open" profile="snap.chromium.chromium" name="/run/udev/data/b179:2" pid=2662 comm="ThreadPoolForeg" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[ 1346.928952] perf: interrupt took too long (2506 > 2500), lowering kernel.perf_event_max_sample_rate to 79750
[ 1576.575374] perf: interrupt took too long (3155 > 3132), lowering kernel.perf_event_max_sample_rate to 63250
[ 1891.986066] perf: interrupt took too long (3952 > 3943), lowering kernel.perf_event_max_sample_rate to 50500
[ 2365.607286] perf: interrupt took too long (4943 > 4940), lowering kernel.perf_event_max_sample_rate to 40250
[ 2915.374204] [drm:mipi_exec_pmic [i915]] *ERROR* Your hardware requires CONFIG_PMIC_OPREGION and it is not set
[ 4307.191462] perf: interrupt took too long (6183 > 6178), lowering kernel.perf_event_max_sample_rate to 32250
[ 5014.286571] [drm:mipi_exec_pmic [i915]] *ERROR* Your hardware requires CONFIG_PMIC_OPREGION and it is not set
[ 7259.634887] [drm:mipi_exec_pmic [i915]] *ERROR* Your hardware requires CONFIG_PMIC_OPREGION and it is not set
[ 8216.179939] perf: interrupt took too long (7752 > 7728), lowering kernel.perf_event_max_sample_rate to 25750
[ 8704.199753] [drm:mipi_exec_pmic [i915]] *ERROR* Your hardware requires CONFIG_PMIC_OPREGION and it is not set
[ 8794.536403] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 8794.548152] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 8794.558278] r8723bs: module is from the staging directory, the quality is unknown, you have been warned.
[ 8794.559234] r8723bs: module verification failed: signature and/or required key missing - tainting kernel
[ 8794.562308] RTL8723BS: module init start
[ 8794.562312] RTL8723BS: rtl8723bs v4.3.5.5_12290.20140916_BTCOEX20140507-4E40
[ 8794.562314] RTL8723BS: rtl8723bs BT-Coex version = BTCOEX20140507-4E40
[ 8794.562360] RTL8723BS: module init ret =0
[ 8868.530724] intel_atomisp2_pm 0000:00:03.0: Refused to change power state, currently in D3
[ 9937.194989] [drm:mipi_exec_pmic [i915]] *ERROR* Your hardware requires CONFIG_PMIC_OPREGION and it is not set
[10162.785757] intel_atomisp2_pm 0000:00:03.0: Refused to change power state, currently in D3
[10162.848909] intel_atomisp2_pm 0000:00:03.0: Refused to change power state, currently in D3
[10276.170933] intel_atomisp2_pm 0000:00:03.0: Refused to change power state, currently in D3
[10276.236465] intel_atomisp2_pm 0000:00:03.0: Refused to change power state, currently in D3
[12794.021374] [drm:mipi_exec_pmic [i915]] *ERROR* Your hardware requires CONFIG_PMIC_OPREGION and it is not set
jean@jean-Switch-One-SW1-011:~$

xubu1957 · Le 12/04/2020, à 06:49

Bonjour,

@aux aidants

Pour :

cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 8794.548152] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'

Je trouve > unix.stackexchange.com/questions/513449/unable-to-load-regulatory-database

[drm:mipi_exec_pmic [i915]] *ERROR* Your hardware requires CONFIG_PMIC_OPREGION and it is not set

Un bug signalé > bugs.launchpad.net/ubuntu/+source/linux/+bug/1858375

_ _ _

Cette remarque :

Le 02/07/2016, Destry a écrit :

Booted into Bios/ South Bridge/ LPSS & SCC CONFIGURATION/ SCC SDIO Support = changed acpi to PCI then saved and exit. After reboot, wifi working! Connected and online
Démarrage dans Bios/ South Bridge/ LPSS & SCC CONFIGURATION/ SCC SDIO Support = changement d'acpi en PCI puis sauvegarde et sortie. Après le redémarrage, le wifi fonctionne ! Connecté et en ligne

> [Solved!] Realtek RTL8723BS not working on tablet Cinnamon 18

Dernière modification par xubu1957 (Le 12/04/2020, à 07:07)

Nuliel · Le 12/04/2020, à 09:50

Ce qui est étonnant c'est que le bluetooth fonctionne. Il communique en UART si j'ai bien compris?

Tu peux dire ce à quoi tu as accès dans le bios? Tu peux utiliser ma signature pour poster des photos du bios?

Le secure boot est bien désactivé dans le bios?

Dernière modification par Nuliel (Le 12/04/2020, à 09:50)

Barrab · Le 12/04/2020, à 14:22

Bonjour,
xubu1957 je regarde tes liens
Naziel, je redémarre l'ordi et je prends des photos du BIOS

Barrab · Le 12/04/2020, à 14:49

Naziel, petite question facile Cooment faire pour utliser ta signature pour t'envoyer les photos? :-)

Barrab · Le 12/04/2020, à 15:49

Voici mon lien Google Drive pour voir les photos du BIOS

https://drive.google.com/open?id=1pOiSV … X2Q4i1WUeZ

Nuliel · Le 12/04/2020, à 16:17

La signature c'est la fin du message, dans la mienne il y a un lien pour poster correctement des retours de commandes et un lien pour poster correctement des photos (et deux trois autres trucs): https://forum.ubuntu-fr.org/viewtopic.php?id=2021144
Mais maintenant que c'est posté, c'est bon

Barrab · Le 12/04/2020, à 16:33

J'ai effectué quelques recherches sur le SDIO et voici quelques adresses qui pourraient être utiles

https://www.silabs.com/community/wirele … ction-ajSx

https://github.com/linux-sunxi/linux-sunxi/issues/249

https://e2e.ti.com/support/wireless-con … h-error-16

https://askubuntu.com/questions/1155262 … e-obtained

https://www.digi.com/resources/document … d-sdio.htm

Barrab · Le 13/04/2020, à 14:27

Salut toutle monde,

J'ai laissé un post à la communauté Acer pour leur demander leur aide

https://community.acer.com/en/discussio … ion#latest

Bonne journée!

Serpico84 · Le 16/11/2020, à 12:20

Hi, sorry if I write in english, but my french is a bit rusty... I saw your post on the Acer community about this, but I'm not able to reply there directly, so I'll do it here.

I have the same machine and I was finally able to make the wifi work. Note that this solution is based on some things I found online that I'm not able to locate anymore, I'm no expert when it comes to linux in general.

Basically, it turns out that the kernel module is missing the device ID. The solution is to download the kernel source matching yours, patching the module by adding the id, and recompile it without recompiling the whole kernel. If you are still interested in solving this, we can go through the details if you want.

Ayral · Le 17/11/2020, à 14:17

Modération :
Salut, désolé si j'écris en anglais, mais mon français est un peu rouillé ... J'ai vu votre message sur la communauté Acer à ce sujet, mais je ne peux pas y répondre directement, donc je le ferai ici.

J'ai la même machine et j'ai enfin pu faire fonctionner le wifi. Notez que cette solution est basée sur certaines choses que j'ai trouvées en ligne que je ne suis plus en mesure de localiser, je ne suis pas un expert en ce qui concerne Linux en général.

Fondamentalement, il s'avère que le module du noyau n'a pas l'ID de périphérique. La solution est de télécharger la source du noyau correspondant à la vôtre, de patcher le module en ajoutant l'id, et de le recompiler sans recompiler tout le noyau. Si vous souhaitez toujours résoudre ce problème, nous pouvons examiner les détails si vous le souhaitez.

Vous pouvez vous même utiliser un traducteur, car la langue du Forum Ubuntu-fr est le Français.

Dernière modification par Ayral (Le 17/11/2020, à 14:19)

Ubuntu-fr

Navigation

Liens de recherche

Annonce

#26 Le 11/04/2020, à 19:02

Re : Wifi Realtek modèle rtl8723bs, je n'arrive pas à le configurer dans 19

#27 Le 11/04/2020, à 20:51

Re : Wifi Realtek modèle rtl8723bs, je n'arrive pas à le configurer dans 19

#28 Le 11/04/2020, à 21:13

Re : Wifi Realtek modèle rtl8723bs, je n'arrive pas à le configurer dans 19

#29 Le 11/04/2020, à 21:36

Re : Wifi Realtek modèle rtl8723bs, je n'arrive pas à le configurer dans 19

#30 Le 11/04/2020, à 22:01

Re : Wifi Realtek modèle rtl8723bs, je n'arrive pas à le configurer dans 19

#31 Le 11/04/2020, à 23:25

Re : Wifi Realtek modèle rtl8723bs, je n'arrive pas à le configurer dans 19

#32 Le 11/04/2020, à 23:31

Re : Wifi Realtek modèle rtl8723bs, je n'arrive pas à le configurer dans 19

#33 Le 11/04/2020, à 23:34

Re : Wifi Realtek modèle rtl8723bs, je n'arrive pas à le configurer dans 19

#34 Le 11/04/2020, à 23:59

Re : Wifi Realtek modèle rtl8723bs, je n'arrive pas à le configurer dans 19

#35 Le 12/04/2020, à 00:01

Re : Wifi Realtek modèle rtl8723bs, je n'arrive pas à le configurer dans 19

#36 Le 12/04/2020, à 00:01

Re : Wifi Realtek modèle rtl8723bs, je n'arrive pas à le configurer dans 19

#37 Le 12/04/2020, à 00:03

Re : Wifi Realtek modèle rtl8723bs, je n'arrive pas à le configurer dans 19

#38 Le 12/04/2020, à 00:40

Re : Wifi Realtek modèle rtl8723bs, je n'arrive pas à le configurer dans 19

#39 Le 12/04/2020, à 06:49

Re : Wifi Realtek modèle rtl8723bs, je n'arrive pas à le configurer dans 19

#40 Le 12/04/2020, à 09:50

Re : Wifi Realtek modèle rtl8723bs, je n'arrive pas à le configurer dans 19

#41 Le 12/04/2020, à 14:22

Re : Wifi Realtek modèle rtl8723bs, je n'arrive pas à le configurer dans 19

#42 Le 12/04/2020, à 14:49

Re : Wifi Realtek modèle rtl8723bs, je n'arrive pas à le configurer dans 19

#43 Le 12/04/2020, à 15:49

Re : Wifi Realtek modèle rtl8723bs, je n'arrive pas à le configurer dans 19

#44 Le 12/04/2020, à 16:17

Re : Wifi Realtek modèle rtl8723bs, je n'arrive pas à le configurer dans 19

#45 Le 12/04/2020, à 16:33

Re : Wifi Realtek modèle rtl8723bs, je n'arrive pas à le configurer dans 19

#46 Le 13/04/2020, à 14:27

Re : Wifi Realtek modèle rtl8723bs, je n'arrive pas à le configurer dans 19

#47 Le 16/11/2020, à 12:20

Re : Wifi Realtek modèle rtl8723bs, je n'arrive pas à le configurer dans 19

#48 Le 17/11/2020, à 14:17

Re : Wifi Realtek modèle rtl8723bs, je n'arrive pas à le configurer dans 19

Pied de page des forums