Probléme montage disque dur externe

hunt · Le 28/08/2020, à 13:02

Bonjour,
J'ai un disque dur externe WD, il est bien détecté sur USB mais il ne se monte pas tout seul au branchement, je galère pour le montage...
Y aurait il une âme charitable pour m'aider ?
Merci par avance

christophe@christophe-System-Product-Name:~$ lsusb
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 002: ID 03f0:0941 Hewlett-Packard 
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 009 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 010 Device 002: ID 1058:25a1 Western Digital Technologies, Inc. 
Bus 010 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 002: ID 058f:6362 Alcor Micro Corp. Flash Card Reader/Writer
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

geole · Le 28/08/2020, à 13:26

Bonjour
Débranche le disque, attends 30 secondes. rebranche le disque, attends de nouveau 30 secondes et donne le retour de

dmesg | tail -50

puis essaie de voir si tu peux le monter avec l'application gnome-disk-utility en attendant l'analyse de la trace dmesg

hunt · Le 28/08/2020, à 13:49

Bonjour,
Merci pour ta réponse...
Voici le retour commande :

christophe@christophe-System-Product-Name:~$ dmesg | tail -50
[23822.935020] .
[23823.958977] .
[23824.986931] .
[23826.006890] .
[23827.030865] .
[23828.086825] .
[23829.110792] .
[23830.138757] .
[23831.158706] .
[23832.214686] .
[23833.238644] .
[23834.262613] .
[23835.286566] .
[23836.342530] .
[23837.366490] .
[23838.390453] .
[23839.414426] .
[23840.438384] .
[23841.462340] .
[23842.486308] .
[23843.510280] .
[23844.566237] .
[23845.590202] .
[23846.614164] .
[23847.638132] .
[23848.694086] .
[23849.718056] .
[23850.742019] .
[23851.765988] .
[23852.821939] .
[23853.845911] .
[23854.869865] .
[23855.893834] .
[23855.893836] not responding...
[23855.902951] sd 9:0:0:0: [sdf] Very big device. Trying to use READ CAPACITY(16).
[23855.903073] sd 9:0:0:0: [sdf] 5860466688 512-byte logical blocks: (3.00 TB/2.73 TiB)
[23855.903075] sd 9:0:0:0: [sdf] 4096-byte physical blocks
[23855.904278] sd 9:0:0:0: [sdf] Write Protect is off
[23855.904281] sd 9:0:0:0: [sdf] Mode Sense: 47 00 10 08
[23855.905307] sd 9:0:0:0: [sdf] No Caching mode page found
[23855.905312] sd 9:0:0:0: [sdf] Assuming drive cache: write through
[23855.908992] sd 9:0:0:0: [sdf] Spinning up disk...
[23856.917801] .
[23857.941762] .
[23858.965730] .
[23859.989695] .
[23861.045652] .
[23862.069615] .
[23863.093586] .
[23864.117540] .
christophe@christophe-System-Product-Name:~$

gnome-disk-utility, il était reconnu tout à l'heure, plus maintenant, mais c'était impossible de rien faire dessus, tout était grisé...

geole · Le 28/08/2020, à 13:58

Je pense que ton disque est neuf et qu'il faudrait lui créer une table de partition GPT (car taille supérieure à 2,2To) avec l'onglet "périphériques" de l'application gparted probablement à installer puis lui créer une ou plusieurs partitions.

S'il n'est pas neuf, il faut installer l'application smartmontools

sudo apt-get install --no-install-recommends smartmontools

et donner le retour de la commande

sudo smartctl   -s on   -a /dev/sdf

Dernière modification par geole (Le 28/08/2020, à 14:05)

hunt · Le 28/08/2020, à 14:03

Problème si tu veux c'est que mon disque il y a déjà mes sauvegardes dessus...
Je l'ai branché sur une version 16.04 d'Ubuntu, sans problème, il a été reconnu de suite...
Et j'ai testé autant sur une machine sous 18.04 ou 20.04, chaque fois le même problème, il n'est pas reconnu...

Edit : le disque est tout neuf, sorti de la boite il y a très peu de temps

Dernière modification par hunt (Le 28/08/2020, à 14:04)

hunt · Le 28/08/2020, à 14:06

Enfin pour être exact dans les termes, si il est reconnu, trouvé via USB, mais ne veut pas se monter...

geole · Le 28/08/2020, à 14:06

avec quoi as-tu fais tes sauvegardes?

il faut installer l'application smartmontools

sudo apt-get install --no-install-recommends smartmontools

et donner le retour de la commande

sudo smartctl   -s on   -a /dev/sdf

geole · Le 28/08/2020, à 14:14

hunt a écrit :

Enfin pour être exact dans les termes, si il est reconnu, trouvé via USB, mais ne veut pas se monter...

La trace dit

[23855.908992] sd 9:0:0:0: [sdf] Spinning up disk...
[23856.917801] .
[23857.941762] .

Pour le moment, j'interprète cela comme une recherche de table de partition...
Dans quelque temps, on devrait avoir une réponse. Donc attendons....un certain temps...

dmesg -w

Tu as écris
"Je l'ai branché sur une version 16.04 d'Ubuntu, sans problème, il a été reconnu de suite..."
est-ce encore actuellement le cas?

Dernière modification par geole (Le 28/08/2020, à 14:18)

hunt · Le 28/08/2020, à 15:29

Oui la sauvegarde de mes fichiers date de hier sur 16.04...

Voici la commande :

christophe@christophe-System-Product-Name:~$ dmesg -w
[    0.000000] microcode: microcode updated early to revision 0xa0b, date = 2010-09-28
[    0.000000] Linux version 4.15.0-112-generic (buildd@lcy01-amd64-027) (gcc version 7.5.0 (Ubuntu 7.5.0-3ubuntu1~18.04)) #113-Ubuntu SMP Thu Jul 9 23:41:39 UTC 2020 (Ubuntu 4.15.0-112.113-generic 4.15.18)
[    0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-4.15.0-112-generic root=UUID=ba1a1613-777d-4bc0-a02f-087cfc93a3a1 ro quiet splash vt.handoff=1
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   Centaur CentaurHauls
[    0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
[    0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[    0.000000] x86/fpu: Enabled xstate features 0x3, context size is 576 bytes, using 'standard' format.
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000e4000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000bfe6ffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000bfe70000-0x00000000bfe7dfff] ACPI data
[    0.000000] BIOS-e820: [mem 0x00000000bfe7e000-0x00000000bfecffff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000bfed0000-0x00000000bfffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fff00000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000043fffffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.5 present.
[    0.000000] DMI: System manufacturer System Product Name/P5Q3, BIOS 0806    08/18/2009
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] e820: last_pfn = 0x440000 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-DFFFF write-protect
[    0.000000]   E0000-EFFFF write-through
[    0.000000]   F0000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask C00000000 write-back
[    0.000000]   1 base 400000000 mask FC0000000 write-back
[    0.000000]   2 base 0C0000000 mask FC0000000 uncachable
[    0.000000]   3 base 0BFF00000 mask FFFF00000 uncachable
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WP  UC- WT  
[    0.000000] total RAM covered: 16383M
[    0.000000] Found optimal setting for mtrr clean up
[    0.000000]  gran_size: 64K 	chunk_size: 2M 	num_reg: 6  	lose cover RAM: 0G
[    0.000000] e820: update [mem 0xbff00000-0xffffffff] usable ==> reserved
[    0.000000] e820: last_pfn = 0xbfe70 max_arch_pfn = 0x400000000
[    0.000000] found SMP MP-table at [mem 0x000ff780-0x000ff78f]
[    0.000000] Scanning 1 areas for low memory corruption
[    0.000000] BRK [0x25ef95000, 0x25ef95fff] PGTABLE
[    0.000000] BRK [0x25ef96000, 0x25ef96fff] PGTABLE
[    0.000000] BRK [0x25ef97000, 0x25ef97fff] PGTABLE
[    0.000000] BRK [0x25ef98000, 0x25ef98fff] PGTABLE
[    0.000000] BRK [0x25ef99000, 0x25ef99fff] PGTABLE
[    0.000000] BRK [0x25ef9a000, 0x25ef9afff] PGTABLE
[    0.000000] BRK [0x25ef9b000, 0x25ef9bfff] PGTABLE
[    0.000000] BRK [0x25ef9c000, 0x25ef9cfff] PGTABLE
[    0.000000] RAMDISK: [mem 0x334ab000-0x35a4cfff]
[    0.000000] ACPI: Early table checksum verification disabled
[    0.000000] ACPI: RSDP 0x00000000000FB1E0 000014 (v00 ACPIAM)
[    0.000000] ACPI: RSDT 0x00000000BFE70000 000040 (v01 A_M_I_ OEMRSDT  08000918 MSFT 00000097)
[    0.000000] ACPI: FACP 0x00000000BFE70200 000084 (v02 A_M_I_ OEMFACP  08000918 MSFT 00000097)
[    0.000000] ACPI: DSDT 0x00000000BFE70440 00A990 (v01 A1098  A1098001 00000001 INTL 20051117)
[    0.000000] ACPI: FACS 0x00000000BFE7E000 000040
[    0.000000] ACPI: APIC 0x00000000BFE70390 00006C (v01 A_M_I_ OEMAPIC  08000918 MSFT 00000097)
[    0.000000] ACPI: MCFG 0x00000000BFE70400 00003C (v01 A_M_I_ OEMMCFG  08000918 MSFT 00000097)
[    0.000000] ACPI: OEMB 0x00000000BFE7E040 000081 (v01 A_M_I_ AMI_OEM  08000918 MSFT 00000097)
[    0.000000] ACPI: HPET 0x00000000BFE7ADD0 000038 (v01 A_M_I_ OEMHPET  08000918 MSFT 00000097)
[    0.000000] ACPI: OSFR 0x00000000BFE7AE10 0000B0 (v01 A_M_I_ OEMOSFR  08000918 MSFT 00000097)
[    0.000000] ACPI: SSDT 0x00000000BFE7E9D0 000A7C (v01 DpgPmm CpuPm    00000012 INTL 20051117)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at [mem 0x0000000000000000-0x000000043fffffff]
[    0.000000] NODE_DATA(0) allocated [mem 0x43ffc9000-0x43fff3fff]
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000001000-0x0000000000ffffff]
[    0.000000]   DMA32    [mem 0x0000000001000000-0x00000000ffffffff]
[    0.000000]   Normal   [mem 0x0000000100000000-0x000000043fffffff]
[    0.000000]   Device   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000001000-0x000000000009efff]
[    0.000000]   node   0: [mem 0x0000000000100000-0x00000000bfe6ffff]
[    0.000000]   node   0: [mem 0x0000000100000000-0x000000043fffffff]
[    0.000000] Reserved but unavailable: 98 pages
[    0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000043fffffff]
[    0.000000] On node 0 totalpages: 4193806
[    0.000000]   DMA zone: 64 pages used for memmap
[    0.000000]   DMA zone: 21 pages reserved
[    0.000000]   DMA zone: 3998 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 12218 pages used for memmap
[    0.000000]   DMA32 zone: 781936 pages, LIFO batch:31
[    0.000000]   Normal zone: 53248 pages used for memmap
[    0.000000]   Normal zone: 3407872 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x808
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a301 base: 0xfed00000
[    0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
[    0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[    0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000e3fff]
[    0.000000] PM: Registered nosave memory: [mem 0x000e4000-0x000fffff]
[    0.000000] PM: Registered nosave memory: [mem 0xbfe70000-0xbfe7dfff]
[    0.000000] PM: Registered nosave memory: [mem 0xbfe7e000-0xbfecffff]
[    0.000000] PM: Registered nosave memory: [mem 0xbfed0000-0xbfffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xc0000000-0xfedfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xffefffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfff00000-0xffffffff]
[    0.000000] e820: [mem 0xc0000000-0xfedfffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
[    0.000000] random: get_random_bytes called from start_kernel+0x99/0x500 with crng_init=0
[    0.000000] setup_percpu: NR_CPUS:8192 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1
[    0.000000] percpu: Embedded 45 pages/cpu s147456 r8192 d28672 u524288
[    0.000000] pcpu-alloc: s147456 r8192 d28672 u524288 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 4128255
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.15.0-112-generic root=UUID=ba1a1613-777d-4bc0-a02f-087cfc93a3a1 ro quiet splash vt.handoff=1
[    0.000000] Calgary: detecting Calgary via BIOS EBDA area
[    0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.000000] Memory: 16379220K/16775224K available (12300K kernel code, 2481K rwdata, 4272K rodata, 2436K init, 2720K bss, 396004K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Kernel/User page tables isolation: enabled
[    0.000000] ftrace: allocating 39378 entries in 154 pages
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=4.
[    0.000000] 	Tasks RCU enabled.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 524544, nr_irqs: 456, preallocated irqs: 16
[    0.000000] vt handoff: transparent VT on vt#1
[    0.000000] Console: colour dummy device 80x25
[    0.000000] console [tty0] enabled
[    0.000000] ACPI: Core revision 20170831
[    0.000000] ACPI: 2 ACPI AML tables successfully acquired and loaded
[    0.000000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484882848 ns
[    0.000000] hpet clockevent registered
[    0.000000] APIC: Switch to symmetric I/O mode setup
[    0.000000] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.020000] tsc: Fast TSC calibration using PIT
[    0.024000] tsc: Detected 2671.721 MHz processor
[    0.024000] Calibrating delay loop (skipped), value calculated using timer frequency.. 5343.44 BogoMIPS (lpj=10686884)
[    0.024000] pid_max: default: 32768 minimum: 301
[    0.024000] Security Framework initialized
[    0.024000] Yama: becoming mindful.
[    0.024000] AppArmor: AppArmor initialized
[    0.032670] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
[    0.035494] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[    0.035609] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes)
[    0.035700] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes)
[    0.035980] CPU0: Thermal monitoring enabled (TM2)
[    0.035982] process: using mwait in idle threads
[    0.035986] Last level iTLB entries: 4KB 128, 2MB 4, 4MB 4
[    0.035987] Last level dTLB entries: 4KB 256, 2MB 0, 4MB 32, 1GB 0
[    0.035989] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization
[    0.035991] Spectre V2 : Mitigation: Full generic retpoline
[    0.035992] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[    0.035993] Speculative Store Bypass: Vulnerable
[    0.036038] MDS: Vulnerable: Clear CPU buffers attempted, no microcode
[    0.036222] Freeing SMP alternatives memory: 36K
[    0.149566] smpboot: CPU0: Intel(R) Core(TM)2 Quad CPU    Q8400  @ 2.66GHz (family: 0x6, model: 0x17, stepping: 0xa)
[    0.149667] Performance Events: PEBS fmt0+, Core2 events, Intel PMU driver.
[    0.149674] ... version:                2
[    0.149675] ... bit width:              40
[    0.149675] ... generic registers:      2
[    0.149676] ... value mask:             000000ffffffffff
[    0.149677] ... max period:             000000007fffffff
[    0.149677] ... fixed-purpose events:   3
[    0.149678] ... event mask:             0000000700000003
[    0.149720] Hierarchical SRCU implementation.
[    0.150824] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
[    0.150842] smp: Bringing up secondary CPUs ...
[    0.150966] x86: Booting SMP configuration:
[    0.150967] .... node  #0, CPUs:      #1 #2 #3
[    0.172044] smp: Brought up 1 node, 4 CPUs
[    0.172044] smpboot: Max logical packages: 1
[    0.172044] smpboot: Total of 4 processors activated (21373.76 BogoMIPS)
[    0.174330] devtmpfs: initialized
[    0.174330] x86/mm: Memory block size: 128MB
[    0.177526] evm: security.selinux
[    0.177527] evm: security.SMACK64
[    0.177527] evm: security.SMACK64EXEC
[    0.177528] evm: security.SMACK64TRANSMUTE
[    0.177529] evm: security.SMACK64MMAP
[    0.177529] evm: security.apparmor
[    0.177530] evm: security.ima
[    0.177530] evm: security.capability
[    0.177549] PM: Registering ACPI NVS region [mem 0xbfe7e000-0xbfecffff] (335872 bytes)
[    0.177549] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.177549] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.177549] pinctrl core: initialized pinctrl subsystem
[    0.177549] RTC time:  6:09:33, date: 08/28/20
[    0.177549] NET: Registered protocol family 16
[    0.177549] audit: initializing netlink subsys (disabled)
[    0.177549] audit: type=2000 audit(1598594973.176:1): state=initialized audit_enabled=0 res=1
[    0.177549] cpuidle: using governor ladder
[    0.177549] cpuidle: using governor menu
[    0.177549] ACPI: bus type PCI registered
[    0.177549] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.177549] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.177549] PCI: not using MMCONFIG
[    0.177549] PCI: Using configuration type 1 for base access
[    0.180510] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.180510] ACPI: Added _OSI(Module Device)
[    0.180510] ACPI: Added _OSI(Processor Device)
[    0.180510] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.180510] ACPI: Added _OSI(Processor Aggregator Device)
[    0.180510] ACPI: Added _OSI(Linux-Dell-Video)
[    0.180510] ACPI: Added _OSI(Linux-Lenovo-NV-HDMI-Audio)
[    0.180510] ACPI: Added _OSI(Linux-HPI-Hybrid-Graphics)
[    0.180510] ACPI: Executed 1 blocks of module-level executable AML code
[    0.188903] ACPI: Dynamic OEM Table Load:
[    0.188909] ACPI: SSDT 0xFFFF99606D176800 000235 (v01 DpgPmm P001Ist  00000011 INTL 20051117)
[    0.189384] ACPI: Dynamic OEM Table Load:
[    0.189388] ACPI: SSDT 0xFFFF99606D174800 000235 (v01 DpgPmm P002Ist  00000012 INTL 20051117)
[    0.189858] ACPI: Dynamic OEM Table Load:
[    0.189863] ACPI: SSDT 0xFFFF99606D175000 000235 (v01 DpgPmm P003Ist  00000012 INTL 20051117)
[    0.190331] ACPI: Dynamic OEM Table Load:
[    0.190336] ACPI: SSDT 0xFFFF99606D176000 000235 (v01 DpgPmm P004Ist  00000012 INTL 20051117)
[    0.192001] ACPI: Interpreter enabled
[    0.192001] ACPI: (supports S0 S1 S3 S4 S5)
[    0.192001] ACPI: Using IOAPIC for interrupt routing
[    0.192001] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.192535] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
[    0.192553] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.192845] ACPI: Enabled 15 GPEs in block 00 to 3F
[    0.202894] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.202900] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.202905] acpi PNP0A08:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
[    0.203243] PCI host bridge to bus 0000:00
[    0.203245] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7 window]
[    0.203247] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    0.203248] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    0.203249] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000dffff window]
[    0.203251] pci_bus 0000:00: root bus resource [mem 0xbff00000-0xffffffff window]
[    0.203252] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.203260] pci 0000:00:00.0: [8086:2e20] type 00 class 0x060000
[    0.203282] DMAR: Forcing write-buffer flush capability
[    0.203282] DMAR: Disabling IOMMU for graphics on this chipset
[    0.203378] pci 0000:00:06.0: [8086:2e29] type 01 class 0x060400
[    0.203414] pci 0000:00:06.0: PME# supported from D0 D3hot D3cold
[    0.203527] pci 0000:00:1a.0: [8086:3a37] type 00 class 0x0c0300
[    0.203566] pci 0000:00:1a.0: reg 0x20: [io  0xa800-0xa81f]
[    0.203690] pci 0000:00:1a.1: [8086:3a38] type 00 class 0x0c0300
[    0.203728] pci 0000:00:1a.1: reg 0x20: [io  0xa880-0xa89f]
[    0.203849] pci 0000:00:1a.2: [8086:3a39] type 00 class 0x0c0300
[    0.203887] pci 0000:00:1a.2: reg 0x20: [io  0xac00-0xac1f]
[    0.204022] pci 0000:00:1a.7: [8086:3a3c] type 00 class 0x0c0320
[    0.204041] pci 0000:00:1a.7: reg 0x10: [mem 0xfcfffc00-0xfcffffff]
[    0.204115] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[    0.204212] pci 0000:00:1b.0: [8086:3a3e] type 00 class 0x040300
[    0.204230] pci 0000:00:1b.0: reg 0x10: [mem 0xfcff8000-0xfcffbfff 64bit]
[    0.204292] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.204391] pci 0000:00:1c.0: [8086:3a40] type 01 class 0x060400
[    0.204456] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.204562] pci 0000:00:1c.1: [8086:3a42] type 01 class 0x060400
[    0.204627] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    0.204729] pci 0000:00:1c.4: [8086:3a48] type 01 class 0x060400
[    0.204793] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[    0.204896] pci 0000:00:1c.5: [8086:3a4a] type 01 class 0x060400
[    0.204961] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
[    0.205064] pci 0000:00:1d.0: [8086:3a34] type 00 class 0x0c0300
[    0.205102] pci 0000:00:1d.0: reg 0x20: [io  0xa080-0xa09f]
[    0.205223] pci 0000:00:1d.1: [8086:3a35] type 00 class 0x0c0300
[    0.205261] pci 0000:00:1d.1: reg 0x20: [io  0xa400-0xa41f]
[    0.205385] pci 0000:00:1d.2: [8086:3a36] type 00 class 0x0c0300
[    0.205423] pci 0000:00:1d.2: reg 0x20: [io  0xa480-0xa49f]
[    0.205549] pci 0000:00:1d.7: [8086:3a3a] type 00 class 0x0c0320
[    0.205568] pci 0000:00:1d.7: reg 0x10: [mem 0xfcfff800-0xfcfffbff]
[    0.205642] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.205737] pci 0000:00:1e.0: [8086:244e] type 01 class 0x060401
[    0.205873] pci 0000:00:1f.0: [8086:3a16] type 00 class 0x060100
[    0.205947] pci 0000:00:1f.0: quirk: [io  0x0800-0x087f] claimed by ICH6 ACPI/GPIO/TCO
[    0.205951] pci 0000:00:1f.0: quirk: [io  0x0500-0x053f] claimed by ICH6 GPIO
[    0.205953] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0294 (mask 0003)
[    0.205957] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 4700 (mask 001f)
[    0.206067] pci 0000:00:1f.2: [8086:3a20] type 00 class 0x01018f
[    0.206081] pci 0000:00:1f.2: reg 0x10: [io  0x9000-0x9007]
[    0.206087] pci 0000:00:1f.2: reg 0x14: [io  0x8c00-0x8c03]
[    0.206093] pci 0000:00:1f.2: reg 0x18: [io  0x8880-0x8887]
[    0.206100] pci 0000:00:1f.2: reg 0x1c: [io  0x8800-0x8803]
[    0.206106] pci 0000:00:1f.2: reg 0x20: [io  0x8480-0x848f]
[    0.206112] pci 0000:00:1f.2: reg 0x24: [io  0x8400-0x840f]
[    0.206225] pci 0000:00:1f.3: [8086:3a30] type 00 class 0x0c0500
[    0.206241] pci 0000:00:1f.3: reg 0x10: [mem 0xfcfff400-0xfcfff4ff 64bit]
[    0.206257] pci 0000:00:1f.3: reg 0x20: [io  0x0400-0x041f]
[    0.206357] pci 0000:00:1f.5: [8086:3a26] type 00 class 0x010185
[    0.206371] pci 0000:00:1f.5: reg 0x10: [io  0xa000-0xa007]
[    0.206377] pci 0000:00:1f.5: reg 0x14: [io  0x9c00-0x9c03]
[    0.206383] pci 0000:00:1f.5: reg 0x18: [io  0x9880-0x9887]
[    0.206390] pci 0000:00:1f.5: reg 0x1c: [io  0x9800-0x9803]
[    0.206396] pci 0000:00:1f.5: reg 0x20: [io  0x9480-0x948f]
[    0.206402] pci 0000:00:1f.5: reg 0x24: [io  0x9400-0x940f]
[    0.206550] pci 0000:01:00.0: [10de:1d01] type 00 class 0x030000
[    0.206569] pci 0000:01:00.0: reg 0x10: [mem 0xfd000000-0xfdffffff]
[    0.206579] pci 0000:01:00.0: reg 0x14: [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.206589] pci 0000:01:00.0: reg 0x1c: [mem 0xce000000-0xcfffffff 64bit pref]
[    0.206597] pci 0000:01:00.0: reg 0x24: [io  0xbc00-0xbc7f]
[    0.206604] pci 0000:01:00.0: reg 0x30: [mem 0xfe700000-0xfe77ffff pref]
[    0.206716] pci 0000:01:00.1: [10de:0fb8] type 00 class 0x040300
[    0.206731] pci 0000:01:00.1: reg 0x10: [mem 0xfe7fc000-0xfe7fffff]
[    0.206872] pci 0000:00:06.0: PCI bridge to [bus 01]
[    0.206875] pci 0000:00:06.0:   bridge window [io  0xb000-0xbfff]
[    0.206877] pci 0000:00:06.0:   bridge window [mem 0xfd000000-0xfe7fffff]
[    0.206879] pci 0000:00:06.0:   bridge window [mem 0xce000000-0xdfffffff 64bit pref]
[    0.206917] pci 0000:00:1c.0: PCI bridge to [bus 05]
[    0.206924] pci 0000:00:1c.0:   bridge window [mem 0xfbf00000-0xfbffffff 64bit pref]
[    0.206988] pci 0000:04:00.0: [1912:0014] type 00 class 0x0c0330
[    0.212003] pci 0000:04:00.0: reg 0x10: [mem 0xfeafe000-0xfeafffff 64bit]
[    0.212195] pci 0000:04:00.0: PME# supported from D0 D3hot D3cold
[    0.224026] pci 0000:00:1c.1: PCI bridge to [bus 04]
[    0.224032] pci 0000:00:1c.1:   bridge window [mem 0xfea00000-0xfeafffff]
[    0.224130] pci 0000:03:00.0: [197b:2363] type 00 class 0x010185
[    0.224229] pci 0000:03:00.0: reg 0x24: [mem 0xfe9fe000-0xfe9fffff]
[    0.224241] pci 0000:03:00.0: reg 0x30: [mem 0xfe9e0000-0xfe9effff pref]
[    0.224297] pci 0000:03:00.0: PME# supported from D3hot
[    0.224375] pci 0000:03:00.1: [197b:2363] type 00 class 0x010185
[    0.224399] pci 0000:03:00.1: reg 0x10: [io  0xdc00-0xdc07]
[    0.224408] pci 0000:03:00.1: reg 0x14: [io  0xd880-0xd883]
[    0.224417] pci 0000:03:00.1: reg 0x18: [io  0xd800-0xd807]
[    0.224426] pci 0000:03:00.1: reg 0x1c: [io  0xd480-0xd483]
[    0.224435] pci 0000:03:00.1: reg 0x20: [io  0xd400-0xd40f]
[    0.224542] pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.224550] pci 0000:00:1c.4: PCI bridge to [bus 03]
[    0.224553] pci 0000:00:1c.4:   bridge window [io  0xd000-0xdfff]
[    0.224556] pci 0000:00:1c.4:   bridge window [mem 0xfe900000-0xfe9fffff]
[    0.224612] pci 0000:02:00.0: [10ec:8168] type 00 class 0x020000
[    0.224638] pci 0000:02:00.0: reg 0x10: [io  0xc800-0xc8ff]
[    0.224662] pci 0000:02:00.0: reg 0x18: [mem 0xfe8ff000-0xfe8fffff 64bit]
[    0.224678] pci 0000:02:00.0: reg 0x20: [mem 0xfbef0000-0xfbefffff 64bit pref]
[    0.224688] pci 0000:02:00.0: reg 0x30: [mem 0xfe8c0000-0xfe8dffff pref]
[    0.224763] pci 0000:02:00.0: supports D1 D2
[    0.224765] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.236021] pci 0000:00:1c.5: PCI bridge to [bus 02]
[    0.236025] pci 0000:00:1c.5:   bridge window [io  0xc000-0xcfff]
[    0.236028] pci 0000:00:1c.5:   bridge window [mem 0xfe800000-0xfe8fffff]
[    0.236033] pci 0000:00:1c.5:   bridge window [mem 0xfbe00000-0xfbefffff 64bit pref]
[    0.236083] pci 0000:06:03.0: [1106:3044] type 00 class 0x0c0010
[    0.236103] pci 0000:06:03.0: reg 0x10: [mem 0xfebff800-0xfebfffff]
[    0.236113] pci 0000:06:03.0: reg 0x14: [io  0xec00-0xec7f]
[    0.236184] pci 0000:06:03.0: supports D2
[    0.236186] pci 0000:06:03.0: PME# supported from D2 D3hot D3cold
[    0.236259] pci 0000:00:1e.0: PCI bridge to [bus 06] (subtractive decode)
[    0.236262] pci 0000:00:1e.0:   bridge window [io  0xe000-0xefff]
[    0.236265] pci 0000:00:1e.0:   bridge window [mem 0xfeb00000-0xfebfffff]
[    0.236269] pci 0000:00:1e.0:   bridge window [io  0x0000-0x0cf7 window] (subtractive decode)
[    0.236271] pci 0000:00:1e.0:   bridge window [io  0x0d00-0xffff window] (subtractive decode)
[    0.236272] pci 0000:00:1e.0:   bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode)
[    0.236273] pci 0000:00:1e.0:   bridge window [mem 0x000d0000-0x000dffff window] (subtractive decode)
[    0.236275] pci 0000:00:1e.0:   bridge window [mem 0xbff00000-0xffffffff window] (subtractive decode)
[    0.237221] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[    0.237306] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[    0.237390] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 14 *15)
[    0.237474] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[    0.237557] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[    0.237641] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 *14 15)
[    0.237724] ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 7 10 11 12 14 15)
[    0.237808] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15)
[    0.238179] SCSI subsystem initialized
[    0.238206] libata version 3.00 loaded.
[    0.238206] pci 0000:01:00.0: vgaarb: setting as boot VGA device
[    0.238206] pci 0000:01:00.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[    0.238206] pci 0000:01:00.0: vgaarb: bridge control possible
[    0.238206] vgaarb: loaded
[    0.238206] ACPI: bus type USB registered
[    0.238206] usbcore: registered new interface driver usbfs
[    0.238206] usbcore: registered new interface driver hub
[    0.238206] usbcore: registered new device driver usb
[    0.238206] EDAC MC: Ver: 3.0.0
[    0.238206] PCI: Using ACPI for IRQ routing
[    0.243773] PCI: pci_cache_line_size set to 64 bytes
[    0.243835] Expanded resource Reserved due to conflict with PCI Bus 0000:00
[    0.243837] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
[    0.243838] e820: reserve RAM buffer [mem 0xbfe70000-0xbfffffff]
[    0.244001] NetLabel: Initializing
[    0.244001] NetLabel:  domain hash size = 128
[    0.244001] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    0.244001] NetLabel:  unlabeled traffic allowed by default
[    0.244658] HPET: 4 timers in total, 0 timers will be used for per-cpu timer
[    0.244663] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[    0.244666] hpet0: 4 comparators, 64-bit 14.318180 MHz counter
[    0.248043] clocksource: Switched to clocksource hpet
[    0.263620] VFS: Disk quotas dquot_6.6.0
[    0.263641] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.263781] AppArmor: AppArmor Filesystem Enabled
[    0.263814] pnp: PnP ACPI init
[    0.263923] system 00:00: [mem 0xfed14000-0xfed19fff] has been reserved
[    0.263929] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.264035] pnp 00:01: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.264405] pnp 00:02: [dma 2]
[    0.264451] pnp 00:02: Plug and Play ACPI device, IDs PNP0700 (active)
[    0.264584] system 00:03: [io  0x0290-0x029f] has been reserved
[    0.264589] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.264834] system 00:04: [io  0x04d0-0x04d1] has been reserved
[    0.264835] system 00:04: [io  0x0800-0x087f] has been reserved
[    0.264837] system 00:04: [io  0x0500-0x057f] could not be reserved
[    0.264839] system 00:04: [mem 0xfed08000-0xfed08fff] has been reserved
[    0.264841] system 00:04: [mem 0xfed1c000-0xfed1ffff] has been reserved
[    0.264843] system 00:04: [mem 0xfed20000-0xfed3ffff] has been reserved
[    0.264844] system 00:04: [mem 0xfed50000-0xfed8ffff] has been reserved
[    0.264846] system 00:04: [mem 0xbff00000-0xbfffffff] has been reserved
[    0.264851] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.265003] system 00:05: [mem 0xffc00000-0xffefffff] has been reserved
[    0.265007] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.265298] pnp 00:06: [dma 0 disabled]
[    0.265362] pnp 00:06: Plug and Play ACPI device, IDs PNP0501 (active)
[    0.265489] system 00:07: [mem 0xfec00000-0xfec00fff] could not be reserved
[    0.265491] system 00:07: [mem 0xfee00000-0xfee00fff] has been reserved
[    0.265496] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.265558] pnp 00:08: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[    0.265686] system 00:09: [mem 0xe0000000-0xefffffff] has been reserved
[    0.265690] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.265961] system 00:0a: [mem 0x00000000-0x0009ffff] could not be reserved
[    0.265963] system 00:0a: [mem 0x000c0000-0x000cffff] could not be reserved
[    0.265965] system 00:0a: [mem 0x000e0000-0x000fffff] could not be reserved
[    0.265967] system 00:0a: [mem 0x00100000-0xbfefffff] could not be reserved
[    0.265971] system 00:0a: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.266158] pnp: PnP ACPI: found 11 devices
[    0.274479] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    0.274496] pci 0000:00:1c.0: bridge window [io  0x1000-0x0fff] to [bus 05] add_size 1000
[    0.274499] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 05] add_size 400000 add_align 100000
[    0.274506] pci 0000:00:1c.1: bridge window [io  0x1000-0x0fff] to [bus 04] add_size 1000
[    0.274508] pci 0000:00:1c.1: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 04] add_size 200000 add_align 100000
[    0.274515] pci 0000:00:1c.4: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 03] add_size 200000 add_align 100000
[    0.274532] pci 0000:00:1c.0: BAR 14: assigned [mem 0xc0000000-0xc03fffff]
[    0.274537] pci 0000:00:1c.1: BAR 15: assigned [mem 0xc0400000-0xc05fffff 64bit pref]
[    0.274541] pci 0000:00:1c.4: BAR 15: assigned [mem 0xc0600000-0xc07fffff 64bit pref]
[    0.274543] pci 0000:00:1c.0: BAR 13: assigned [io  0x1000-0x1fff]
[    0.274545] pci 0000:00:1c.1: BAR 13: assigned [io  0x2000-0x2fff]
[    0.274548] pci 0000:00:06.0: PCI bridge to [bus 01]
[    0.274550] pci 0000:00:06.0:   bridge window [io  0xb000-0xbfff]
[    0.274552] pci 0000:00:06.0:   bridge window [mem 0xfd000000-0xfe7fffff]
[    0.274554] pci 0000:00:06.0:   bridge window [mem 0xce000000-0xdfffffff 64bit pref]
[    0.274557] pci 0000:00:1c.0: PCI bridge to [bus 05]
[    0.274560] pci 0000:00:1c.0:   bridge window [io  0x1000-0x1fff]
[    0.274563] pci 0000:00:1c.0:   bridge window [mem 0xc0000000-0xc03fffff]
[    0.274566] pci 0000:00:1c.0:   bridge window [mem 0xfbf00000-0xfbffffff 64bit pref]
[    0.274570] pci 0000:00:1c.1: PCI bridge to [bus 04]
[    0.274572] pci 0000:00:1c.1:   bridge window [io  0x2000-0x2fff]
[    0.274576] pci 0000:00:1c.1:   bridge window [mem 0xfea00000-0xfeafffff]
[    0.274579] pci 0000:00:1c.1:   bridge window [mem 0xc0400000-0xc05fffff 64bit pref]
[    0.274583] pci 0000:00:1c.4: PCI bridge to [bus 03]
[    0.274585] pci 0000:00:1c.4:   bridge window [io  0xd000-0xdfff]
[    0.274589] pci 0000:00:1c.4:   bridge window [mem 0xfe900000-0xfe9fffff]
[    0.274591] pci 0000:00:1c.4:   bridge window [mem 0xc0600000-0xc07fffff 64bit pref]
[    0.274596] pci 0000:00:1c.5: PCI bridge to [bus 02]
[    0.274598] pci 0000:00:1c.5:   bridge window [io  0xc000-0xcfff]
[    0.274602] pci 0000:00:1c.5:   bridge window [mem 0xfe800000-0xfe8fffff]
[    0.274604] pci 0000:00:1c.5:   bridge window [mem 0xfbe00000-0xfbefffff 64bit pref]
[    0.274609] pci 0000:00:1e.0: PCI bridge to [bus 06]
[    0.274611] pci 0000:00:1e.0:   bridge window [io  0xe000-0xefff]
[    0.274615] pci 0000:00:1e.0:   bridge window [mem 0xfeb00000-0xfebfffff]
[    0.274621] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7 window]
[    0.274622] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff window]
[    0.274624] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[    0.274625] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff window]
[    0.274627] pci_bus 0000:00: resource 8 [mem 0xbff00000-0xffffffff window]
[    0.274628] pci_bus 0000:01: resource 0 [io  0xb000-0xbfff]
[    0.274630] pci_bus 0000:01: resource 1 [mem 0xfd000000-0xfe7fffff]
[    0.274631] pci_bus 0000:01: resource 2 [mem 0xce000000-0xdfffffff 64bit pref]
[    0.274632] pci_bus 0000:05: resource 0 [io  0x1000-0x1fff]
[    0.274634] pci_bus 0000:05: resource 1 [mem 0xc0000000-0xc03fffff]
[    0.274635] pci_bus 0000:05: resource 2 [mem 0xfbf00000-0xfbffffff 64bit pref]
[    0.274636] pci_bus 0000:04: resource 0 [io  0x2000-0x2fff]
[    0.274638] pci_bus 0000:04: resource 1 [mem 0xfea00000-0xfeafffff]
[    0.274639] pci_bus 0000:04: resource 2 [mem 0xc0400000-0xc05fffff 64bit pref]
[    0.274641] pci_bus 0000:03: resource 0 [io  0xd000-0xdfff]
[    0.274642] pci_bus 0000:03: resource 1 [mem 0xfe900000-0xfe9fffff]
[    0.274643] pci_bus 0000:03: resource 2 [mem 0xc0600000-0xc07fffff 64bit pref]
[    0.274644] pci_bus 0000:02: resource 0 [io  0xc000-0xcfff]
[    0.274646] pci_bus 0000:02: resource 1 [mem 0xfe800000-0xfe8fffff]
[    0.274647] pci_bus 0000:02: resource 2 [mem 0xfbe00000-0xfbefffff 64bit pref]
[    0.274649] pci_bus 0000:06: resource 0 [io  0xe000-0xefff]
[    0.274650] pci_bus 0000:06: resource 1 [mem 0xfeb00000-0xfebfffff]
[    0.274651] pci_bus 0000:06: resource 4 [io  0x0000-0x0cf7 window]
[    0.274653] pci_bus 0000:06: resource 5 [io  0x0d00-0xffff window]
[    0.274654] pci_bus 0000:06: resource 6 [mem 0x000a0000-0x000bffff window]
[    0.274655] pci_bus 0000:06: resource 7 [mem 0x000d0000-0x000dffff window]
[    0.274657] pci_bus 0000:06: resource 8 [mem 0xbff00000-0xffffffff window]
[    0.274761] NET: Registered protocol family 2
[    0.274972] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.275250] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    0.275461] TCP: Hash tables configured (established 131072 bind 65536)
[    0.275552] UDP hash table entries: 8192 (order: 6, 262144 bytes)
[    0.275640] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes)
[    0.275785] NET: Registered protocol family 1
[    0.277075] pci 0000:01:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[    0.277089] pci 0000:00:1c.1: enabling device (0106 -> 0107)
[    0.277264] pci 0000:03:00.0: async suspend disabled to avoid multi-function power-on ordering issue
[    0.277269] pci 0000:03:00.1: async suspend disabled to avoid multi-function power-on ordering issue
[    0.277277] PCI: CLS 32 bytes, default 64
[    0.277330] Unpacking initramfs...
[    0.833673] Freeing initrd memory: 38536K
[    0.833727] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    0.833729] software IO TLB: mapped [mem 0xbbe70000-0xbfe70000] (64MB)
[    0.833941] Scanning for low memory corruption every 60 seconds
[    0.834627] Initialise system trusted keyrings
[    0.834638] Key type blacklist registered
[    0.834737] workingset: timestamp_bits=36 max_order=22 bucket_order=0
[    0.836337] zbud: loaded
[    0.836920] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.837102] fuse init (API version 7.26)
[    0.839499] Key type asymmetric registered
[    0.839501] Asymmetric key parser 'x509' registered
[    0.839547] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[    0.839622] io scheduler noop registered
[    0.839624] io scheduler deadline registered
[    0.839656] io scheduler cfq registered (default)
[    0.840063] pcieport 0000:00:1c.0: enabling device (0106 -> 0107)
[    0.840678] vesafb: mode is 1920x1080x32, linelength=7680, pages=0
[    0.840679] vesafb: scrolling: redraw
[    0.840681] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[    0.840696] vesafb: framebuffer at 0xcf000000, mapped to 0x        (ptrval), using 8128k, total 8128k
[    0.840834] Console: switching to colour frame buffer device 240x67
[    0.840878] fb0: VESA VGA frame buffer device
[    0.840893] intel_idle: does not run on family 6 model 23
[    0.840998] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[    0.841009] ACPI: Power Button [PWRB]
[    0.841051] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[    0.841094] ACPI: Power Button [PWRF]
[    0.841498] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[    0.861909] 00:06: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[    0.864976] Linux agpgart interface v0.103
[    0.867113] loop: module loaded
[    0.867254] ata_piix 0000:00:1f.2: version 2.13
[    0.867369] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[    0.868871] scsi host0: ata_piix
[    0.868967] scsi host1: ata_piix
[    0.869006] ata1: SATA max UDMA/133 cmd 0x9000 ctl 0x8c00 bmdma 0x8480 irq 19
[    0.869009] ata2: SATA max UDMA/133 cmd 0x8880 ctl 0x8800 bmdma 0x8488 irq 19
[    0.869116] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
[    0.870233] scsi host2: ata_piix
[    0.870345] scsi host3: ata_piix
[    0.870386] ata3: SATA max UDMA/133 cmd 0xa000 ctl 0x9c00 bmdma 0x9480 irq 19
[    0.870388] ata4: SATA max UDMA/133 cmd 0x9880 ctl 0x9800 bmdma 0x9488 irq 19
[    0.870535] libphy: Fixed MDIO Bus: probed
[    0.870536] tun: Universal TUN/TAP device driver, 1.6
[    0.870603] PPP generic driver version 2.4.2
[    0.870674] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.870680] ehci-pci: EHCI PCI platform driver
[    0.870806] ehci-pci 0000:00:1a.7: EHCI Host Controller
[    0.870812] ehci-pci 0000:00:1a.7: new USB bus registered, assigned bus number 1
[    0.870823] ehci-pci 0000:00:1a.7: debug port 1
[    0.874724] ehci-pci 0000:00:1a.7: cache line size of 32 is not supported
[    0.874737] ehci-pci 0000:00:1a.7: irq 18, io mem 0xfcfffc00
[    0.888018] ehci-pci 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[    0.888070] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.888072] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.888074] usb usb1: Product: EHCI Host Controller
[    0.888076] usb usb1: Manufacturer: Linux 4.15.0-112-generic ehci_hcd
[    0.888078] usb usb1: SerialNumber: 0000:00:1a.7
[    0.888218] hub 1-0:1.0: USB hub found
[    0.888225] hub 1-0:1.0: 6 ports detected
[    0.888473] ehci-pci 0000:00:1d.7: EHCI Host Controller
[    0.888478] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 2
[    0.888488] ehci-pci 0000:00:1d.7: debug port 1
[    0.892394] ehci-pci 0000:00:1d.7: cache line size of 32 is not supported
[    0.892404] ehci-pci 0000:00:1d.7: irq 23, io mem 0xfcfff800
[    0.908019] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    0.908076] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    0.908078] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.908080] usb usb2: Product: EHCI Host Controller
[    0.908082] usb usb2: Manufacturer: Linux 4.15.0-112-generic ehci_hcd
[    0.908083] usb usb2: SerialNumber: 0000:00:1d.7
[    0.908209] hub 2-0:1.0: USB hub found
[    0.908219] hub 2-0:1.0: 6 ports detected
[    0.908372] ehci-platform: EHCI generic platform driver
[    0.908384] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.908394] ohci-pci: OHCI PCI platform driver
[    0.908405] ohci-platform: OHCI generic platform driver
[    0.908414] uhci_hcd: USB Universal Host Controller Interface driver
[    0.908502] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[    0.908508] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[    0.908513] uhci_hcd 0000:00:1a.0: detected 2 ports
[    0.908535] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000a800
[    0.908578] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    0.908579] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.908581] usb usb3: Product: UHCI Host Controller
[    0.908582] usb usb3: Manufacturer: Linux 4.15.0-112-generic uhci_hcd
[    0.908583] usb usb3: SerialNumber: 0000:00:1a.0
[    0.908696] hub 3-0:1.0: USB hub found
[    0.908702] hub 3-0:1.0: 2 ports detected
[    0.908879] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[    0.908884] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[    0.908889] uhci_hcd 0000:00:1a.1: detected 2 ports
[    0.908910] uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000a880
[    0.908952] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    0.908954] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.908955] usb usb4: Product: UHCI Host Controller
[    0.908956] usb usb4: Manufacturer: Linux 4.15.0-112-generic uhci_hcd
[    0.908958] usb usb4: SerialNumber: 0000:00:1a.1
[    0.909072] hub 4-0:1.0: USB hub found
[    0.909078] hub 4-0:1.0: 2 ports detected
[    0.909240] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[    0.909245] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
[    0.909250] uhci_hcd 0000:00:1a.2: detected 2 ports
[    0.909266] uhci_hcd 0000:00:1a.2: irq 18, io base 0x0000ac00
[    0.909308] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[    0.909310] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.909311] usb usb5: Product: UHCI Host Controller
[    0.909312] usb usb5: Manufacturer: Linux 4.15.0-112-generic uhci_hcd
[    0.909314] usb usb5: SerialNumber: 0000:00:1a.2
[    0.909425] hub 5-0:1.0: USB hub found
[    0.909430] hub 5-0:1.0: 2 ports detected
[    0.909596] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    0.909602] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
[    0.909607] uhci_hcd 0000:00:1d.0: detected 2 ports
[    0.909622] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000a080
[    0.909662] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[    0.909664] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.909665] usb usb6: Product: UHCI Host Controller
[    0.909666] usb usb6: Manufacturer: Linux 4.15.0-112-generic uhci_hcd
[    0.909668] usb usb6: SerialNumber: 0000:00:1d.0
[    0.909779] hub 6-0:1.0: USB hub found
[    0.909785] hub 6-0:1.0: 2 ports detected
[    0.909945] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    0.909952] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
[    0.909957] uhci_hcd 0000:00:1d.1: detected 2 ports
[    0.909973] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000a400
[    0.910015] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[    0.910016] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.910018] usb usb7: Product: UHCI Host Controller
[    0.910019] usb usb7: Manufacturer: Linux 4.15.0-112-generic uhci_hcd
[    0.910020] usb usb7: SerialNumber: 0000:00:1d.1
[    0.910131] hub 7-0:1.0: USB hub found
[    0.910137] hub 7-0:1.0: 2 ports detected
[    0.910301] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    0.910306] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
[    0.910311] uhci_hcd 0000:00:1d.2: detected 2 ports
[    0.910327] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000a480
[    0.910368] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
[    0.910370] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.910371] usb usb8: Product: UHCI Host Controller
[    0.910372] usb usb8: Manufacturer: Linux 4.15.0-112-generic uhci_hcd
[    0.910374] usb usb8: SerialNumber: 0000:00:1d.2
[    0.910485] hub 8-0:1.0: USB hub found
[    0.910491] hub 8-0:1.0: 2 ports detected
[    0.910609] xhci_hcd 0000:04:00.0: Resetting
[    1.192714] ata3: SATA link down (SStatus 0 SControl 300)
[    1.203286] ata4: SATA link down (SStatus 0 SControl 300)
[    1.224017] usb 1-1: new high-speed USB device number 2 using ehci-pci
[    1.380018] usb 6-1: new low-speed USB device number 2 using uhci_hcd
[    1.381906] usb 1-1: New USB device found, idVendor=058f, idProduct=6362
[    1.381908] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    1.381910] usb 1-1: Product: Mass Storage Device
[    1.381912] usb 1-1: Manufacturer: Generic
[    1.381913] usb 1-1: SerialNumber: 058F312D81B1
[    1.576046] usb 6-1: New USB device found, idVendor=03f0, idProduct=0941
[    1.576049] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    1.576050] usb 6-1: Product: HP X500 USB Optical Mouse
[    1.576052] usb 6-1: Manufacturer: PixArt
[    1.652061] ata2.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.652072] ata2.01: SATA link down (SStatus 0 SControl 300)
[    1.652081] ata2.01: link offline, clearing class 3 to NONE
[    1.652224] ata1.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.652233] ata1.01: SATA link down (SStatus 0 SControl 300)
[    1.654663] ata1.00: ATA-10: WDC WD1003FZEX-00K3CA0, 01.01A01, max UDMA/133
[    1.654665] ata1.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    1.657199] ata1.00: configured for UDMA/133
[    1.657389] scsi 0:0:0:0: Direct-Access     ATA      WDC WD1003FZEX-0 1A01 PQ: 0 ANSI: 5
[    1.657616] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.657678] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[    1.657680] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    1.657701] sd 0:0:0:0: [sda] Write Protect is off
[    1.657703] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.657731] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.672124] ata2.00: ATAPI: HL-DT-ST DVDRAM GH22NS50, TN01, max UDMA/100
[    1.689112]  sda: sda1
[    1.689460] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.696126] ata2.00: configured for UDMA/100
[    1.705433] scsi 1:0:0:0: CD-ROM            HL-DT-ST DVDRAM GH22NS50  TN01 PQ: 0 ANSI: 5
[    1.767788] sr 1:0:0:0: [sr0] scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[    1.767790] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.767931] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    1.768020] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    1.852022] tsc: Refined TSC clocksource calibration: 2671.603 MHz
[    1.852031] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x268274ebcf4, max_idle_ns: 440795260388 ns
[    1.948212] xhci_hcd 0000:04:00.0: xHCI Host Controller
[    1.948220] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 9
[    1.953631] xhci_hcd 0000:04:00.0: hcc params 0x014050cf hci version 0x100 quirks 0x0000000000000410
[    1.953889] usb usb9: New USB device found, idVendor=1d6b, idProduct=0002
[    1.953891] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.953893] usb usb9: Product: xHCI Host Controller
[    1.953894] usb usb9: Manufacturer: Linux 4.15.0-112-generic xhci-hcd
[    1.953895] usb usb9: SerialNumber: 0000:04:00.0
[    1.954016] hub 9-0:1.0: USB hub found
[    1.954029] hub 9-0:1.0: 4 ports detected
[    1.954172] xhci_hcd 0000:04:00.0: xHCI Host Controller
[    1.954176] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 10
[    1.954179] xhci_hcd 0000:04:00.0: Host supports USB 3.0  SuperSpeed
[    1.957121] usb usb10: We don't know the algorithms for LPM for this host, disabling LPM.
[    1.957139] usb usb10: New USB device found, idVendor=1d6b, idProduct=0003
[    1.957141] usb usb10: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.957142] usb usb10: Product: xHCI Host Controller
[    1.957144] usb usb10: Manufacturer: Linux 4.15.0-112-generic xhci-hcd
[    1.957145] usb usb10: SerialNumber: 0000:04:00.0
[    1.957259] hub 10-0:1.0: USB hub found
[    1.957274] hub 10-0:1.0: 4 ports detected
[    1.957481] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[    1.957482] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[    1.957988] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.958099] mousedev: PS/2 mouse device common for all mice
[    1.958315] rtc_cmos 00:01: RTC can wake from S4
[    1.958437] rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
[    1.958458] rtc_cmos 00:01: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[    1.958467] i2c /dev entries driver
[    1.958527] device-mapper: uevent: version 1.0.3
[    1.958625] device-mapper: ioctl: 4.37.0-ioctl (2017-09-20) initialised: dm-devel@redhat.com
[    1.958711] ledtrig-cpu: registered to indicate activity on CPUs
[    1.959199] NET: Registered protocol family 10
[    1.964194] Segment Routing with IPv6
[    1.964217] NET: Registered protocol family 17
[    1.964260] Key type dns_resolver registered
[    1.964565] mce: Using 6 MCE banks
[    1.964579] RAS: Correctable Errors collector initialized.
[    1.964619] microcode: sig=0x1067a, pf=0x10, revision=0xa0b
[    1.964711] microcode: Microcode Update Driver: v2.2.
[    1.964722] sched_clock: Marking stable (1964700706, 0)->(1991116728, -26416022)
[    1.965070] registered taskstats version 1
[    1.965079] Loading compiled-in X.509 certificates
[    1.968152] Loaded X.509 cert 'Build time autogenerated kernel key: 1d4b83cbc5f7a3cd7e4471a5cf69d65d9314bdf5'
[    1.968171] zswap: loaded using pool lzo/zbud
[    1.972431] Key type big_key registered
[    1.972435] Key type trusted registered
[    1.974466] Key type encrypted registered
[    1.974468] AppArmor: AppArmor sha1 policy hashing enabled
[    1.974471] ima: No TPM chip found, activating TPM-bypass! (rc=-19)
[    1.974474] ima: Allocated hash algorithm: sha1
[    1.974489] evm: HMAC attrs: 0x1
[    1.974829]   Magic number: 0:368:166
[    1.974994] rtc_cmos 00:01: setting system clock to 2020-08-28 06:09:35 UTC (1598594975)
[    1.976143] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    1.976144] EDD information not available.
[    1.979395] Freeing unused kernel image memory: 2436K
[    1.979476] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2
[    2.004023] Write protecting the kernel read-only data: 20480k
[    2.004913] Freeing unused kernel image memory: 2008K
[    2.005550] Freeing unused kernel image memory: 1872K
[    2.015599] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    2.015688] x86/mm: Checking user space page tables
[    2.025718] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    2.160622] pata_jmicron 0000:03:00.1: enabling device (0000 -> 0001)
[    2.161790] usb-storage 1-1:1.0: USB Mass Storage device detected
[    2.162983] scsi host5: pata_jmicron
[    2.163714] hidraw: raw HID events driver (C) Jiri Kosina
[    2.165617] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    2.165628] r8169 0000:02:00.0: can't disable ASPM; OS doesn't have ASPM control
[    2.165731] scsi host4: usb-storage 1-1:1.0
[    2.165856] usbcore: registered new interface driver usb-storage
[    2.166052] r8169 0000:02:00.0 eth0: RTL8168c/8111c at 0x        (ptrval), 90:e6:ba:4a:64:e9, XID 1c4000c0 IRQ 17
[    2.166054] r8169 0000:02:00.0 eth0: jumbo features [frames: 6128 bytes, tx checksumming: ko]
[    2.166592] scsi host6: pata_jmicron
[    2.166647] ata5: PATA max UDMA/100 cmd 0xdc00 ctl 0xd880 bmdma 0xd400 irq 17
[    2.166648] ata6: PATA max UDMA/100 cmd 0xd800 ctl 0xd480 bmdma 0xd408 irq 17
[    2.166679] ahci 0000:03:00.0: version 3.0
[    2.167555] usbcore: registered new interface driver uas
[    2.176875] ahci 0000:03:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
[    2.176881] ahci 0000:03:00.0: flags: 64bit ncq pm led clo pmp pio slum part 
[    2.180125] scsi host7: ahci
[    2.181330] usbcore: registered new interface driver usbhid
[    2.181331] usbhid: USB HID core driver
[    2.184174] scsi host8: ahci
[    2.184236] ata7: SATA max UDMA/133 abar m8192@0xfe9fe000 port 0xfe9fe100 irq 16
[    2.184239] ata8: SATA max UDMA/133 abar m8192@0xfe9fe000 port 0xfe9fe180 irq 16
[    2.204524] r8169 0000:02:00.0 enp2s0: renamed from eth0
[    2.206765] input: PixArt HP X500 USB Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb6/6-1/6-1:1.0/0003:03F0:0941.0001/input/input3
[    2.206869] hid-generic 0003:03F0:0941.0001: input,hidraw0: USB HID v1.11 Mouse [PixArt HP X500 USB Optical Mouse] on usb-0000:00:1d.0-1/input0
[    2.236116] firewire_ohci 0000:06:03.0: added OHCI v1.10 device as card 0, 4 IR + 8 IT contexts, quirks 0x11
[    2.498212] ata8: SATA link down (SStatus 0 SControl 300)
[    2.500439] ata7: SATA link down (SStatus 0 SControl 300)
[    2.692581] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[    2.748125] firewire_core 0000:06:03.0: created device fw0: GUID 001e8c0000b042f4, S400
[    2.880066] clocksource: Switched to clocksource tsc
[    3.004634] random: fast init done
[    3.196935] scsi 4:0:0:0: Direct-Access     Generic  USB SD Reader    1.00 PQ: 0 ANSI: 0
[    3.197670] scsi 4:0:0:1: Direct-Access     Generic  USB CF Reader    1.01 PQ: 0 ANSI: 0
[    3.198292] scsi 4:0:0:2: Direct-Access     Generic  USB SM Reader    1.02 PQ: 0 ANSI: 0
[    3.199041] scsi 4:0:0:3: Direct-Access     Generic  USB MS Reader    1.03 PQ: 0 ANSI: 0
[    3.199365] sd 4:0:0:0: Attached scsi generic sg2 type 0
[    3.199557] sd 4:0:0:1: Attached scsi generic sg3 type 0
[    3.199740] sd 4:0:0:2: Attached scsi generic sg4 type 0
[    3.199927] sd 4:0:0:3: Attached scsi generic sg5 type 0
[    3.202537] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[    3.203161] sd 4:0:0:1: [sdc] Attached SCSI removable disk
[    3.203784] sd 4:0:0:2: [sdd] Attached SCSI removable disk
[    3.204535] sd 4:0:0:3: [sde] Attached SCSI removable disk
[    4.104416] ip_tables: (C) 2000-2006 Netfilter Core Team
[    4.156583] random: systemd: uninitialized urandom read (16 bytes read)
[    4.174496] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[    4.192123] systemd[1]: Detected architecture x86-64.
[    4.192179] random: systemd: uninitialized urandom read (16 bytes read)
[    4.192193] random: systemd: uninitialized urandom read (16 bytes read)
[    4.210324] systemd[1]: Set hostname to <christophe-System-Product-Name>.
[    4.554088] random: crng init done
[    4.554091] random: 7 urandom warning(s) missed due to ratelimiting
[    5.825362] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    5.825401] systemd[1]: Reached target Remote File Systems.
[    5.825611] systemd[1]: Created slice User and Session Slice.
[    5.825778] systemd[1]: Created slice System Slice.
[    5.825859] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[    5.825947] systemd[1]: Listening on Journal Socket (/dev/log).
[    5.825965] systemd[1]: Reached target Slices.
[    6.035583] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[    6.438079] Adding 2097148k swap on /swapfile.  Priority:-2 extents:6 across:2260988k FS
[    7.336474] systemd-journald[286]: Received request to flush runtime journal from PID 1
[    7.586258] lp: driver loaded but no devices found
[    8.403178] ppdev: user-space parallel port driver
[   16.119280] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   16.138908] ipmi message handler version 39.2
[   16.140545] ipmi device interface
[   16.154114] ATK0110 ATK0110:00: hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().
[   16.180114] snd_hda_intel 0000:01:00.1: Disabling MSI
[   16.180123] snd_hda_intel 0000:01:00.1: Handle vga_switcheroo audio client
[   16.205489] ACPI Warning: SystemIO range 0x0000000000000828-0x000000000000082F conflicts with OpRegion 0x0000000000000800-0x000000000000084F (\PMRG) (20170831/utaddress-247)
[   16.205496] ACPI Warning: SystemIO range 0x0000000000000828-0x000000000000082F conflicts with OpRegion 0x0000000000000800-0x000000000000084F (\PMRG) (20170831/utaddress-247)
[   16.205502] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   16.205505] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053F conflicts with OpRegion 0x0000000000000500-0x000000000000053F (\GPS0) (20170831/utaddress-247)
[   16.205508] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053F conflicts with OpRegion 0x0000000000000500-0x000000000000053F (\GPS0) (20170831/utaddress-247)
[   16.205511] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   16.205512] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052F conflicts with OpRegion 0x0000000000000500-0x000000000000053F (\GPS0) (20170831/utaddress-247)
[   16.205515] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052F conflicts with OpRegion 0x0000000000000500-0x000000000000053F (\GPS0) (20170831/utaddress-247)
[   16.205518] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   16.205519] lpc_ich: Resource conflict(s) found affecting gpio_ich
[   16.208837] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC1200: line_outs=4 (0x14/0x15/0x16/0x17/0x0) type:line
[   16.208840] snd_hda_codec_realtek hdaudioC0D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   16.208842] snd_hda_codec_realtek hdaudioC0D0:    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[   16.208843] snd_hda_codec_realtek hdaudioC0D0:    mono: mono_out=0x0
[   16.208844] snd_hda_codec_realtek hdaudioC0D0:    dig-out=0x11/0x1e
[   16.208846] snd_hda_codec_realtek hdaudioC0D0:    inputs:
[   16.208847] snd_hda_codec_realtek hdaudioC0D0:      Front Mic=0x19
[   16.208849] snd_hda_codec_realtek hdaudioC0D0:      Rear Mic=0x18
[   16.208851] snd_hda_codec_realtek hdaudioC0D0:      Line=0x1a
[   16.224057] input: HDA Intel Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input4
[   16.224126] input: HDA Intel Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input5
[   16.224189] input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6
[   16.224251] input: HDA Intel Line Out Front as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[   16.224317] input: HDA Intel Line Out Surround as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[   16.224431] input: HDA Intel Line Out CLFE as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[   16.224497] input: HDA Intel Line Out Side as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[   16.224561] input: HDA Intel Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[   16.320590] intel_powerclamp: No package C-state available
[   16.380161] intel_powerclamp: No package C-state available
[   16.420333] intel_powerclamp: No package C-state available
[   16.476412] intel_powerclamp: No package C-state available
[   16.928520] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:06.0/0000:01:00.1/sound/card1/input12
[   16.928584] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:06.0/0000:01:00.1/sound/card1/input13
[   18.171766] nvidia: loading out-of-tree module taints kernel.
[   18.171777] nvidia: module license 'NVIDIA' taints kernel.
[   18.171777] Disabling lock debugging due to kernel taint
[   18.183170] nvidia: module verification failed: signature and/or required key missing - tainting kernel
[   18.192181] nvidia-nvlink: Nvlink Core is being initialized, major device number 240
[   18.192594] nvidia 0000:01:00.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=none:owns=io+mem
[   18.192724] NVRM: loading NVIDIA UNIX x86_64 Kernel Module  390.138  Thu May 14 01:01:53 PDT 2020 (using threaded interrupts)
[   18.712170] nvidia-modeset: Loading NVIDIA Kernel Mode Setting Driver for UNIX platforms  390.138  Thu May 14 04:02:47 PDT 2020
[   18.713369] [drm] [nvidia-drm] [GPU ID 0x00000100] Loading driver
[   18.713371] [drm] Initialized nvidia-drm 0.0.0 20160202 for 0000:01:00.0 on minor 0
[   19.355308] nvidia-uvm: Loaded the UVM driver in 8 mode, major device number 239
[   19.825248] audit: type=1400 audit(1598594993.345:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-oopslash" pid=573 comm="apparmor_parser"
[   19.825728] audit: type=1400 audit(1598594993.345:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=572 comm="apparmor_parser"
[   19.825732] audit: type=1400 audit(1598594993.345:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=572 comm="apparmor_parser"
[   19.825734] audit: type=1400 audit(1598594993.345:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=572 comm="apparmor_parser"
[   19.826162] audit: type=1400 audit(1598594993.345:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/sbin/dhclient" pid=569 comm="apparmor_parser"
[   19.826166] audit: type=1400 audit(1598594993.345:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=569 comm="apparmor_parser"
[   19.826168] audit: type=1400 audit(1598594993.345:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=569 comm="apparmor_parser"
[   19.826170] audit: type=1400 audit(1598594993.345:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=569 comm="apparmor_parser"
[   19.827145] audit: type=1400 audit(1598594993.345:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-senddoc" pid=574 comm="apparmor_parser"
[   19.827556] audit: type=1400 audit(1598594993.345:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-xpdfimport" pid=576 comm="apparmor_parser"
[   20.165700] resource sanity check: requesting [mem 0x000c0000-0x000fffff], which spans more than PCI Bus 0000:00 [mem 0x000d0000-0x000dffff window]
[   20.165952] caller os_map_kernel_space.part.8+0x10b/0x150 [nvidia] mapping multiple BARs
[   28.174915] IPv6: ADDRCONF(NETDEV_UP): enp2s0: link is not ready
[   28.216092] r8169 0000:02:00.0 enp2s0: link down
[   28.216102] r8169 0000:02:00.0 enp2s0: link down
[   28.216192] IPv6: ADDRCONF(NETDEV_UP): enp2s0: link is not ready
[   29.865831] r8169 0000:02:00.0 enp2s0: link up
[   29.865841] IPv6: ADDRCONF(NETDEV_CHANGE): enp2s0: link becomes ready
[   31.386437] resource sanity check: requesting [mem 0x000c0000-0x000fffff], which spans more than PCI Bus 0000:00 [mem 0x000d0000-0x000dffff window]
[   31.386661] caller os_map_kernel_space.part.8+0x10b/0x150 [nvidia] mapping multiple BARs
[   57.325600] rfkill: input handler disabled
[  617.961381] perf: interrupt took too long (2506 > 2500), lowering kernel.perf_event_max_sample_rate to 79750
[ 1618.829062] perf: interrupt took too long (3136 > 3132), lowering kernel.perf_event_max_sample_rate to 63750
[20917.688311] usb 10-2: new SuperSpeed USB device number 2 using xhci_hcd
[20917.713826] usb 10-2: New USB device found, idVendor=1058, idProduct=25a1
[20917.713829] usb 10-2: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[20917.713830] usb 10-2: Product: Elements 25A1
[20917.713832] usb 10-2: Manufacturer: Western Digital
[20917.713834] usb 10-2: SerialNumber: 5758313244333044464B3830
[20917.715794] usb-storage 10-2:1.0: USB Mass Storage device detected
[20917.716090] scsi host9: usb-storage 10-2:1.0
[20918.736440] scsi 9:0:0:0: Direct-Access     WD       Elements 25A1    1018 PQ: 0 ANSI: 6
[20918.736768] sd 9:0:0:0: Attached scsi generic sg6 type 0
[20918.740240] sd 9:0:0:0: [sdf] Spinning up disk...
[20919.759524] .
[20920.783504] .
[20921.807486] .
[20922.831460] .
[20923.855432] .
[20924.879411] .
[20925.903380] .
[20926.927375] .
[20927.983344] .
[20929.007319] .
[20930.031295] .
[20931.055270] .
[20932.111246] .
[20933.135228] .
[20934.159197] .
[20935.183179] .
[20936.239157] .
[20937.263136] .
[20938.287118] .
[20939.311086] .
[20940.367065] .
[20941.391041] .
[20942.415020] .
[20943.439000] .
[20944.462976] .
[20945.486952] .
[20946.510931] .
[20947.534906] .
[20948.590878] .
[20949.614862] .
[20950.638834] .
[20951.662828] .
[20952.718793] .
[20953.742776] .
[20954.766755] .
[20955.790722] .
[20956.846708] .
[20957.870684] .
[20958.894650] .
[20959.918636] .
[20960.942621] .
[20961.970598] .
[20962.994556] .
[20964.014542] .
[20965.070512] .
[20966.094507] .
[20967.118482] .
[20968.142451] .
[20969.198436] .
[20970.222402] .
[20971.246379] .
[20972.270354] .
[20973.326331] .
[20974.350314] .
[20975.374315] .
[20976.398264] .
[20977.422246] .
[20978.446232] .
[20979.470211] .
[20980.494221] .
[20981.550153] .
[20982.574148] .
[20983.598117] .
[20984.622079] .
[20985.646061] .
[20986.674043] .
[20987.694026] .
[20988.718001] .
[20989.773967] .
[20990.797949] .
[20991.821946] .
[20992.849906] .
[20993.902030] .
[20994.929856] .
[20995.949852] .
[20996.973822] .
[20997.997785] .
[20999.021764] .
[21000.045740] .
[21001.069720] .
[21002.125723] .
[21003.149691] .
[21004.173652] .
[21005.197621] .
[21006.221634] .
[21007.245582] .
[21008.269565] .
[21009.293540] .
[21010.349512] .
[21011.373492] .
[21012.397471] .
[21013.421450] .
[21014.477424] .
[21015.501400] .
[21016.525381] .
[21017.549358] .
[21018.573333] .
[21019.597311] .
[21019.597313] not responding...
[21019.597462] sd 9:0:0:0: [sdf] Very big device. Trying to use READ CAPACITY(16).
[21019.597582] sd 9:0:0:0: [sdf] 5860466688 512-byte logical blocks: (3.00 TB/2.73 TiB)
[21019.597584] sd 9:0:0:0: [sdf] 4096-byte physical blocks
[21019.598674] sd 9:0:0:0: [sdf] Write Protect is off
[21019.598678] sd 9:0:0:0: [sdf] Mode Sense: 47 00 10 08
[21019.599986] sd 9:0:0:0: [sdf] No Caching mode page found
[21019.599992] sd 9:0:0:0: [sdf] Assuming drive cache: write through
[21019.603535] sd 9:0:0:0: [sdf] Spinning up disk...
[21020.621291] .
[21021.645267] .
[21022.701249] .
[21023.725214] .
[21024.749212] .
[21025.773179] .
[21026.797158] .
[21027.821132] .
[21028.845109] .
[21029.869090] .
[21030.925069] .
[21031.949053] .
[21032.973033] .
[21033.996999] .
[21035.020979] .
[21036.044977] .
[21037.068937] .
[21038.092908] .
[21039.148884] .
[21040.172882] .
[21041.196848] .
[21042.220854] .
[21043.276810] .
[21044.300785] .
[21045.328740] .
[21046.348733] .
[21047.372716] .
[21048.396692] .
[21049.424659] .
[21050.444636] .
[21051.500633] .
[21052.524591] .
[21053.548566] .
[21054.572551] .
[21055.596527] .
[21056.620510] .
[21057.644482] .
[21058.668451] .
[21059.724451] .
[21060.748409] .
[21061.772382] .
[21062.796362] .
[21063.852336] .
[21064.876313] .
[21065.900296] .
[21066.924272] .
[21067.948253] .
[21068.972226] .
[21069.996209] .
[21071.020183] .
[21072.076160] .
[21073.100137] .
[21074.124118] .
[21075.148091] .
[21076.172074] .
[21077.196053] .
[21078.220025] .
[21079.244007] .
[21080.299979] .
[21081.323958] .
[21082.347940] .
[21083.371913] .
[21084.395890] .
[21085.419877] .
[21086.443848] .
[21087.467823] .
[21088.523805] .
[21089.547783] .
[21090.571759] .
[21091.595737] .
[21092.651711] .
[21093.675694] .
[21094.699678] .
[21095.723654] .
[21096.747627] .
[21097.771604] .
[21098.795580] .
[21099.819571] .
[21100.875546] .
[21101.899506] .
[21102.923510] .
[21103.947476] .
[21104.971450] .
[21105.995442] .
[21107.019407] .
[21108.043380] .
[21109.099361] .
[21110.123334] .
[21111.147314] .
[21112.171290] .
[21113.227263] .
[21114.251240] .
[21115.275221] .
[21116.299203] .
[21117.323173] .
[21118.347152] .
[21119.371130] .
[21120.395113] .
[21120.395115] not responding...
[21267.079963] INFO: task kworker/u8:4:110 blocked for more than 120 seconds.
[21267.079968]       Tainted: P           OE    4.15.0-112-generic #113-Ubuntu
[21267.079970] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[21267.079973] kworker/u8:4    D    0   110      2 0x80000000
[21267.079981] Workqueue: events_unbound async_run_entry_fn
[21267.079983] Call Trace:
[21267.079989]  __schedule+0x24e/0x880
[21267.079991]  schedule+0x2c/0x80
[21267.079993]  io_schedule+0x16/0x40
[21267.079996]  do_read_cache_page+0x3b6/0x580
[21267.079999]  ? blkdev_writepages+0x40/0x40
[21267.080002]  ? page_cache_tree_insert+0xe0/0xe0
[21267.080004]  read_cache_page+0x15/0x20
[21267.080007]  read_dev_sector+0x2d/0xe0
[21267.080009]  read_lba+0x130/0x220
[21267.080011]  ? kmem_cache_alloc_trace+0x1b3/0x1d0
[21267.080014]  efi_partition+0x138/0x790
[21267.080016]  ? string+0x60/0x90
[21267.080018]  ? vsnprintf+0xfb/0x510
[21267.080020]  ? snprintf+0x45/0x70
[21267.080022]  ? is_gpt_valid.part.6+0x420/0x420
[21267.080024]  check_partition+0x130/0x230
[21267.080026]  ? is_gpt_valid.part.6+0x420/0x420
[21267.080027]  ? check_partition+0x130/0x230
[21267.080029]  rescan_partitions+0xaa/0x350
[21267.080032]  bdev_disk_changed+0x53/0x60
[21267.080034]  __blkdev_get+0x34a/0x510
[21267.080036]  blkdev_get+0x129/0x320
[21267.080039]  ? wake_up_bit+0x42/0x50
[21267.080041]  ? unlock_new_inode+0x4c/0x80
[21267.080043]  ? bdget+0x108/0x120
[21267.080045]  device_add_disk+0x38b/0x490
[21267.080048]  ? __pm_runtime_use_autosuspend+0x54/0x70
[21267.080051]  sd_probe_async+0x102/0x230
[21267.080053]  async_run_entry_fn+0x3c/0x150
[21267.080056]  process_one_work+0x1de/0x420
[21267.080058]  worker_thread+0x32/0x410
[21267.080060]  kthread+0x121/0x140
[21267.080062]  ? process_one_work+0x420/0x420
[21267.080064]  ? kthread_create_worker_on_cpu+0x70/0x70
[21267.080066]  ret_from_fork+0x35/0x40
[21301.538000] sd 9:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[21301.538015] sd 9:0:0:0: [sdf] tag#0 Sense Key : Not Ready [current] 
[21301.538020] sd 9:0:0:0: [sdf] tag#0 Add. Sense: Logical unit is in process of becoming ready
[21301.538025] sd 9:0:0:0: [sdf] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[21301.538028] print_req_error: I/O error, dev sdf, sector 0
[21301.538036] Buffer I/O error on dev sdf, logical block 0, async page read
[21481.586664] sd 9:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[21481.586675] sd 9:0:0:0: [sdf] tag#0 Sense Key : Not Ready [current] 
[21481.586679] sd 9:0:0:0: [sdf] tag#0 Add. Sense: Logical unit is in process of becoming ready
[21481.586685] sd 9:0:0:0: [sdf] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[21481.586688] print_req_error: I/O error, dev sdf, sector 0
[21481.586696] Buffer I/O error on dev sdf, logical block 0, async page read
[21629.568336] INFO: task kworker/u8:4:110 blocked for more than 120 seconds.
[21629.568342]       Tainted: P           OE    4.15.0-112-generic #113-Ubuntu
[21629.568344] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[21629.568346] kworker/u8:4    D    0   110      2 0x80000000
[21629.568354] Workqueue: events_unbound async_run_entry_fn
[21629.568355] Call Trace:
[21629.568361]  __schedule+0x24e/0x880
[21629.568364]  schedule+0x2c/0x80
[21629.568365]  io_schedule+0x16/0x40
[21629.568368]  do_read_cache_page+0x3b6/0x580
[21629.568372]  ? blkdev_writepages+0x40/0x40
[21629.568375]  ? page_cache_tree_insert+0xe0/0xe0
[21629.568378]  ? ldm_get_vblks+0x5c0/0x5c0
[21629.568379]  read_cache_page+0x15/0x20
[21629.568381]  read_dev_sector+0x2d/0xe0
[21629.568383]  ldm_partition+0x95/0xfb0
[21629.568385]  ? osf_partition+0x230/0x230
[21629.568387]  ? read_cache_page+0x15/0x20
[21629.568389]  ? read_dev_sector+0x2d/0xe0
[21629.568390]  ? sgi_partition+0x44/0x270
[21629.568393]  ? snprintf+0x45/0x70
[21629.568395]  ? ldm_get_vblks+0x5c0/0x5c0
[21629.568397]  check_partition+0x130/0x230
[21629.568399]  rescan_partitions+0xaa/0x350
[21629.568401]  bdev_disk_changed+0x53/0x60
[21629.568403]  __blkdev_get+0x34a/0x510
[21629.568405]  blkdev_get+0x129/0x320
[21629.568408]  ? wake_up_bit+0x42/0x50
[21629.568411]  ? unlock_new_inode+0x4c/0x80
[21629.568413]  ? bdget+0x108/0x120
[21629.568415]  device_add_disk+0x38b/0x490
[21629.568418]  ? __pm_runtime_use_autosuspend+0x54/0x70
[21629.568420]  sd_probe_async+0x102/0x230
[21629.568423]  async_run_entry_fn+0x3c/0x150
[21629.568426]  process_one_work+0x1de/0x420
[21629.568428]  worker_thread+0x32/0x410
[21629.568430]  kthread+0x121/0x140
[21629.568431]  ? process_one_work+0x420/0x420
[21629.568433]  ? kthread_create_worker_on_cpu+0x70/0x70
[21629.568436]  ret_from_fork+0x35/0x40
[21661.835456] sd 9:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[21661.835466] sd 9:0:0:0: [sdf] tag#0 Sense Key : Not Ready [current] 
[21661.835470] sd 9:0:0:0: [sdf] tag#0 Add. Sense: Logical unit is in process of becoming ready
[21661.835474] sd 9:0:0:0: [sdf] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[21661.835477] print_req_error: I/O error, dev sdf, sector 0
[21661.835484] Buffer I/O error on dev sdf, logical block 0, async page read
[21661.835496] ldm_validate_partition_table(): Disk read failed.
[21843.684212] sd 9:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[21843.684225] sd 9:0:0:0: [sdf] tag#0 Sense Key : Not Ready [current] 
[21843.684230] sd 9:0:0:0: [sdf] tag#0 Add. Sense: Logical unit is in process of becoming ready
[21843.684235] sd 9:0:0:0: [sdf] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[21843.684238] print_req_error: I/O error, dev sdf, sector 0
[21843.684246] Buffer I/O error on dev sdf, logical block 0, async page read
[21992.056855] INFO: task kworker/u8:4:110 blocked for more than 120 seconds.
[21992.056860]       Tainted: P           OE    4.15.0-112-generic #113-Ubuntu
[21992.056863] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[21992.056865] kworker/u8:4    D    0   110      2 0x80000000
[21992.056873] Workqueue: events_unbound async_run_entry_fn
[21992.056875] Call Trace:
[21992.056881]  __schedule+0x24e/0x880
[21992.056883]  schedule+0x2c/0x80
[21992.056885]  io_schedule+0x16/0x40
[21992.056888]  do_read_cache_page+0x3b6/0x580
[21992.056891]  ? blkdev_writepages+0x40/0x40
[21992.056894]  ? page_cache_tree_insert+0xe0/0xe0
[21992.056896]  read_cache_page+0x15/0x20
[21992.056899]  read_dev_sector+0x2d/0xe0
[21992.056901]  osf_partition+0x48/0x230
[21992.056902]  ? sgi_partition+0x44/0x270
[21992.056904]  ? snprintf+0x45/0x70
[21992.056907]  ? msdos_partition+0xa70/0xa70
[21992.056909]  check_partition+0x130/0x230
[21992.056911]  rescan_partitions+0xaa/0x350
[21992.056913]  bdev_disk_changed+0x53/0x60
[21992.056915]  __blkdev_get+0x34a/0x510
[21992.056917]  blkdev_get+0x129/0x320
[21992.056920]  ? wake_up_bit+0x42/0x50
[21992.056923]  ? unlock_new_inode+0x4c/0x80
[21992.056925]  ? bdget+0x108/0x120
[21992.056927]  device_add_disk+0x38b/0x490
[21992.056930]  ? __pm_runtime_use_autosuspend+0x54/0x70
[21992.056932]  sd_probe_async+0x102/0x230
[21992.056935]  async_run_entry_fn+0x3c/0x150
[21992.056937]  process_one_work+0x1de/0x420
[21992.056940]  worker_thread+0x32/0x410
[21992.056941]  kthread+0x121/0x140
[21992.056943]  ? process_one_work+0x420/0x420
[21992.056945]  ? kthread_create_worker_on_cpu+0x70/0x70
[21992.056948]  ret_from_fork+0x35/0x40
[22025.482999] sd 9:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[22025.483003] sd 9:0:0:0: [sdf] tag#0 Sense Key : Not Ready [current] 
[22025.483005] sd 9:0:0:0: [sdf] tag#0 Add. Sense: Logical unit is in process of becoming ready
[22025.483007] sd 9:0:0:0: [sdf] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[22025.483009] print_req_error: I/O error, dev sdf, sector 0
[22025.483015] Buffer I/O error on dev sdf, logical block 0, async page read
[22207.281961] sd 9:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[22207.281974] sd 9:0:0:0: [sdf] tag#0 Sense Key : Not Ready [current] 
[22207.281978] sd 9:0:0:0: [sdf] tag#0 Add. Sense: Logical unit is in process of becoming ready
[22207.281983] sd 9:0:0:0: [sdf] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[22207.281987] print_req_error: I/O error, dev sdf, sector 0
[22207.281994] Buffer I/O error on dev sdf, logical block 0, async page read
[22354.545438] INFO: task kworker/u8:4:110 blocked for more than 120 seconds.
[22354.545443]       Tainted: P           OE    4.15.0-112-generic #113-Ubuntu
[22354.545445] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[22354.545448] kworker/u8:4    D    0   110      2 0x80000000
[22354.545456] Workqueue: events_unbound async_run_entry_fn
[22354.545457] Call Trace:
[22354.545463]  __schedule+0x24e/0x880
[22354.545466]  schedule+0x2c/0x80
[22354.545467]  io_schedule+0x16/0x40
[22354.545470]  do_read_cache_page+0x3b6/0x580
[22354.545473]  ? blkdev_writepages+0x40/0x40
[22354.545476]  ? page_cache_tree_insert+0xe0/0xe0
[22354.545478]  read_cache_page+0x15/0x20
[22354.545481]  read_dev_sector+0x2d/0xe0
[22354.545483]  amiga_partition+0x86/0x4f0
[22354.545485]  ? sun_partition+0x48/0x380
[22354.545487]  ? osf_partition+0x48/0x230
[22354.545489]  ? snprintf+0x45/0x70
[22354.545491]  ? put_partition+0x90/0x90
[22354.545493]  check_partition+0x130/0x230
[22354.545495]  rescan_partitions+0xaa/0x350
[22354.545497]  bdev_disk_changed+0x53/0x60
[22354.545499]  __blkdev_get+0x34a/0x510
[22354.545501]  blkdev_get+0x129/0x320
[22354.545504]  ? wake_up_bit+0x42/0x50
[22354.545507]  ? unlock_new_inode+0x4c/0x80
[22354.545509]  ? bdget+0x108/0x120
[22354.545511]  device_add_disk+0x38b/0x490
[22354.545514]  ? __pm_runtime_use_autosuspend+0x54/0x70
[22354.545517]  sd_probe_async+0x102/0x230
[22354.545519]  async_run_entry_fn+0x3c/0x150
[22354.545522]  process_one_work+0x1de/0x420
[22354.545524]  worker_thread+0x32/0x410
[22354.545526]  kthread+0x121/0x140
[22354.545528]  ? process_one_work+0x420/0x420
[22354.545529]  ? kthread_create_worker_on_cpu+0x70/0x70
[22354.545532]  ret_from_fork+0x35/0x40
[22389.030873] sd 9:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[22389.030932] sd 9:0:0:0: [sdf] tag#0 Sense Key : Not Ready [current] 
[22389.030937] sd 9:0:0:0: [sdf] tag#0 Add. Sense: Logical unit is in process of becoming ready
[22389.030942] sd 9:0:0:0: [sdf] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[22389.030945] print_req_error: I/O error, dev sdf, sector 0
[22389.030953] Buffer I/O error on dev sdf, logical block 0, async page read
[22389.030967] Dev sdf: unable to read RDB block 0
[22570.879839] sd 9:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[22570.879852] sd 9:0:0:0: [sdf] tag#0 Sense Key : Not Ready [current] 
[22570.879857] sd 9:0:0:0: [sdf] tag#0 Add. Sense: Logical unit is in process of becoming ready
[22570.879862] sd 9:0:0:0: [sdf] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[22570.879866] print_req_error: I/O error, dev sdf, sector 0
[22570.879873] Buffer I/O error on dev sdf, logical block 0, async page read
[22717.034063] INFO: task kworker/u8:4:110 blocked for more than 120 seconds.
[22717.034068]       Tainted: P           OE    4.15.0-112-generic #113-Ubuntu
[22717.034070] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[22717.034072] kworker/u8:4    D    0   110      2 0x80000000
[22717.034080] Workqueue: events_unbound async_run_entry_fn
[22717.034082] Call Trace:
[22717.034088]  __schedule+0x24e/0x880
[22717.034091]  schedule+0x2c/0x80
[22717.034093]  io_schedule+0x16/0x40
[22717.034095]  do_read_cache_page+0x3b6/0x580
[22717.034098]  ? blkdev_writepages+0x40/0x40
[22717.034102]  ? page_cache_tree_insert+0xe0/0xe0
[22717.034105]  ? cmdline_partition+0x100/0x100
[22717.034106]  read_cache_page+0x15/0x20
[22717.034108]  read_dev_sector+0x2d/0xe0
[22717.034110]  mac_partition+0x48/0x3c0
[22717.034112]  ? ldm_ldmdb_add+0x866/0xd40
[22717.034114]  ? snprintf+0x45/0x70
[22717.034116]  ? cmdline_partition+0x100/0x100
[22717.034118]  check_partition+0x130/0x230
[22717.034120]  rescan_partitions+0xaa/0x350
[22717.034122]  bdev_disk_changed+0x53/0x60
[22717.034124]  __blkdev_get+0x34a/0x510
[22717.034127]  blkdev_get+0x129/0x320
[22717.034129]  ? wake_up_bit+0x42/0x50
[22717.034132]  ? unlock_new_inode+0x4c/0x80
[22717.034134]  ? bdget+0x108/0x120
[22717.034136]  device_add_disk+0x38b/0x490
[22717.034139]  ? __pm_runtime_use_autosuspend+0x54/0x70
[22717.034142]  sd_probe_async+0x102/0x230
[22717.034144]  async_run_entry_fn+0x3c/0x150
[22717.034147]  process_one_work+0x1de/0x420
[22717.034149]  worker_thread+0x32/0x410
[22717.034151]  kthread+0x121/0x140
[22717.034153]  ? process_one_work+0x420/0x420
[22717.034155]  ? kthread_create_worker_on_cpu+0x70/0x70
[22717.034157]  ret_from_fork+0x35/0x40
[22752.528698] sd 9:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[22752.528713] sd 9:0:0:0: [sdf] tag#0 Sense Key : Not Ready [current] 
[22752.528717] sd 9:0:0:0: [sdf] tag#0 Add. Sense: Logical unit is in process of becoming ready
[22752.528722] sd 9:0:0:0: [sdf] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[22752.528726] print_req_error: I/O error, dev sdf, sector 0
[22752.528734] Buffer I/O error on dev sdf, logical block 0, async page read
[22934.327670] sd 9:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[22934.327682] sd 9:0:0:0: [sdf] tag#0 Sense Key : Not Ready [current] 
[22934.327685] sd 9:0:0:0: [sdf] tag#0 Add. Sense: Logical unit is in process of becoming ready
[22934.327690] sd 9:0:0:0: [sdf] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 18 00 00 00 08 00 00
[22934.327693] print_req_error: I/O error, dev sdf, sector 24
[22934.327700] Buffer I/O error on dev sdf, logical block 3, async page read
[23079.511950] INFO: task kworker/u8:4:110 blocked for more than 120 seconds.
[23079.511956]       Tainted: P           OE    4.15.0-112-generic #113-Ubuntu
[23079.511957] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[23079.511960] kworker/u8:4    D    0   110      2 0x80000000
[23079.511968] Workqueue: events_unbound async_run_entry_fn
[23079.511970] Call Trace:
[23079.511976]  __schedule+0x24e/0x880
[23079.511978]  schedule+0x2c/0x80
[23079.511980]  io_schedule+0x16/0x40
[23079.511982]  do_read_cache_page+0x3b6/0x580
[23079.511986]  ? blkdev_writepages+0x40/0x40
[23079.511989]  ? page_cache_tree_insert+0xe0/0xe0
[23079.511992]  ? efi_partition+0x790/0x790
[23079.511993]  read_cache_page+0x15/0x20
[23079.511995]  read_dev_sector+0x2d/0xe0
[23079.511997]  karma_partition+0x44/0x200
[23079.511999]  ? snprintf+0x45/0x70
[23079.512002]  check_partition+0x130/0x230
[23079.512004]  rescan_partitions+0xaa/0x350
[23079.512006]  bdev_disk_changed+0x53/0x60
[23079.512008]  __blkdev_get+0x34a/0x510
[23079.512010]  blkdev_get+0x129/0x320
[23079.512013]  ? wake_up_bit+0x42/0x50
[23079.512016]  ? unlock_new_inode+0x4c/0x80
[23079.512018]  ? bdget+0x108/0x120
[23079.512020]  device_add_disk+0x38b/0x490
[23079.512023]  ? __pm_runtime_use_autosuspend+0x54/0x70
[23079.512026]  sd_probe_async+0x102/0x230
[23079.512028]  async_run_entry_fn+0x3c/0x150
[23079.512031]  process_one_work+0x1de/0x420
[23079.512033]  worker_thread+0x32/0x410
[23079.512035]  kthread+0x121/0x140
[23079.512037]  ? process_one_work+0x420/0x420
[23079.512038]  ? kthread_create_worker_on_cpu+0x70/0x70
[23079.512041]  ret_from_fork+0x35/0x40
[23116.126630] sd 9:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[23116.126643] sd 9:0:0:0: [sdf] tag#0 Sense Key : Not Ready [current] 
[23116.126648] sd 9:0:0:0: [sdf] tag#0 Add. Sense: Logical unit is in process of becoming ready
[23116.126653] sd 9:0:0:0: [sdf] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[23116.126656] print_req_error: I/O error, dev sdf, sector 0
[23116.126664] Buffer I/O error on dev sdf, logical block 0, async page read
[23297.925799] sd 9:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[23297.925815] sd 9:0:0:0: [sdf] tag#0 Sense Key : Not Ready [current] 
[23297.925819] sd 9:0:0:0: [sdf] tag#0 Add. Sense: Logical unit is in process of becoming ready
[23297.925825] sd 9:0:0:0: [sdf] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[23297.925829] print_req_error: I/O error, dev sdf, sector 0
[23297.925837] Buffer I/O error on dev sdf, logical block 0, async page read
[23297.925852]  sdf: unable to read partition table
[23297.931037] sd 9:0:0:0: [sdf] Spinning up disk...
[23298.956391] .
[23481.574736] sd 9:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[23481.574740] sd 9:0:0:0: [sdf] tag#0 Sense Key : Not Ready [current] 
[23481.574742] sd 9:0:0:0: [sdf] tag#0 Add. Sense: Logical unit is in process of becoming ready
[23481.574746] sd 9:0:0:0: [sdf] tag#0 CDB: Read(16) 88 00 00 00 00 01 5d 4f 9f 80 00 00 00 08 00 00
[23481.574748] print_req_error: I/O error, dev sdf, sector 5860466560
[23482.596146] .
[23482.596147] not responding...
[23482.598199] sd 9:0:0:0: [sdf] Attached SCSI disk
[23684.828346] usb 10-2: USB disconnect, device number 2
[23753.918248] usb 10-3: new SuperSpeed USB device number 3 using xhci_hcd
[23753.943723] usb 10-3: New USB device found, idVendor=1058, idProduct=25a1
[23753.943726] usb 10-3: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[23753.943728] usb 10-3: Product: Elements 25A1
[23753.943730] usb 10-3: Manufacturer: Western Digital
[23753.943732] usb 10-3: SerialNumber: 5758313244333044464B3830
[23753.945404] usb-storage 10-3:1.0: USB Mass Storage device detected
[23753.945678] scsi host9: usb-storage 10-3:1.0
[23754.970344] scsi 9:0:0:0: Direct-Access     WD       Elements 25A1    1018 PQ: 0 ANSI: 6
[23754.970694] sd 9:0:0:0: Attached scsi generic sg6 type 0
[23754.974224] sd 9:0:0:0: [sdf] Spinning up disk...
[23755.993431] .
[23757.017399] .
[23758.041358] .
[23759.065309] .
[23760.089273] .
[23761.113242] .
[23762.169208] .
[23763.193175] .
[23764.217132] .
[23765.241101] .
[23766.297054] .
[23767.321027] .
[23768.344972] .
[23769.368939] .
[23770.392918] .
[23771.416884] .
[23772.444842] .
[23773.464803] .
[23774.520783] .
[23775.544730] .
[23776.568702] .
[23777.592651] .
[23778.648604] .
[23779.672585] .
[23780.696524] .
[23781.720496] .
[23782.776458] .
[23783.800431] .
[23784.824378] .
[23785.848335] .
[23786.904298] .
[23787.928265] .
[23788.952228] .
[23789.976195] .
[23791.000162] .
[23792.028117] .
[23793.048097] .
[23794.072046] .
[23795.128003] .
[23796.151963] .
[23797.175926] .
[23798.199902] .
[23799.255864] .
[23800.279855] .
[23801.303805] .
[23802.327749] .
[23803.383719] .
[23804.407691] .
[23805.431643] .
[23806.455606] .
[23807.479562] .
[23808.503524] .
[23809.527491] .
[23810.555460] .
[23811.607413] .
[23812.631377] .
[23813.655349] .
[23814.679297] .
[23815.735263] .
[23816.759245] .
[23817.783194] .
[23818.807162] .
[23819.863137] .
[23820.887087] .
[23821.911038] .
[23822.935020] .
[23823.958977] .
[23824.986931] .
[23826.006890] .
[23827.030865] .
[23828.086825] .
[23829.110792] .
[23830.138757] .
[23831.158706] .
[23832.214686] .
[23833.238644] .
[23834.262613] .
[23835.286566] .
[23836.342530] .
[23837.366490] .
[23838.390453] .
[23839.414426] .
[23840.438384] .
[23841.462340] .
[23842.486308] .
[23843.510280] .
[23844.566237] .
[23845.590202] .
[23846.614164] .
[23847.638132] .
[23848.694086] .
[23849.718056] .
[23850.742019] .
[23851.765988] .
[23852.821939] .
[23853.845911] .
[23854.869865] .
[23855.893834] .
[23855.893836] not responding...
[23855.902951] sd 9:0:0:0: [sdf] Very big device. Trying to use READ CAPACITY(16).
[23855.903073] sd 9:0:0:0: [sdf] 5860466688 512-byte logical blocks: (3.00 TB/2.73 TiB)
[23855.903075] sd 9:0:0:0: [sdf] 4096-byte physical blocks
[23855.904278] sd 9:0:0:0: [sdf] Write Protect is off
[23855.904281] sd 9:0:0:0: [sdf] Mode Sense: 47 00 10 08
[23855.905307] sd 9:0:0:0: [sdf] No Caching mode page found
[23855.905312] sd 9:0:0:0: [sdf] Assuming drive cache: write through
[23855.908992] sd 9:0:0:0: [sdf] Spinning up disk...
[23856.917801] .
[23857.941762] .
[23858.965730] .
[23859.989695] .
[23861.045652] .
[23862.069615] .
[23863.093586] .
[23864.117540] .
[23865.173510] .
[23866.197473] .
[23867.221433] .
[23868.245401] .
[23869.301365] .
[23870.325329] .
[23871.349309] .
[23872.373260] .
[23873.397217] .
[23874.421195] .
[23875.445143] .
[23876.469110] .
[23877.525093] .
[23878.549038] .
[23879.573000] .
[23880.596963] .
[23881.652929] .
[23882.676892] .
[23883.700858] .
[23884.724823] .
[23885.780784] .
[23886.804746] .
[23887.828711] .
[23888.852676] .
[23889.876646] .
[23890.900605] .
[23891.924577] .
[23892.948538] .
[23894.004499] .
[23895.028454] .
[23896.052429] .
[23897.076405] .
[23898.132354] .
[23899.156315] .
[23900.180289] .
[23901.204250] .
[23902.260209] .
[23903.284173] .
[23904.308136] .
[23905.332106] .
[23906.356068] .
[23907.380043] .
[23908.404004] .
[23909.427974] .
[23910.483925] .
[23911.507897] .
[23912.531854] .
[23913.555819] .
[23914.611790] .
[23915.635762] .
[23916.659708] .
[23917.683682] .
[23918.739649] .
[23919.763603] .
[23920.787568] .
[23921.815527] .
[23922.835496] .
[23923.859458] .
[23924.887442] .
[23925.907388] .
[23926.963388] .
[23927.987324] .
[23929.011311] .
[23930.035257] .
[23931.091220] .
[23932.115177] .
[23933.139153] .
[23934.163114] .
[23935.219069] .
[23936.243033] .
[23937.266997] .
[23938.290964] .
[23939.314932] .
[23940.338896] .
[23941.362865] .
[23942.386830] .
[23943.442785] .
[23944.466762] .
[23945.490720] .
[23946.514687] .
[23947.570646] .
[23948.594610] .
[23949.618574] .
[23950.642538] .
[23951.698508] .
[23952.722475] .
[23953.746434] .
[23954.770402] .
[23955.794363] .
[23956.818330] .
[23956.818332] not responding...
[24137.732576] sd 9:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[24137.732580] sd 9:0:0:0: [sdf] tag#0 Sense Key : Not Ready [current] 
[24137.732582] sd 9:0:0:0: [sdf] tag#0 Add. Sense: Logical unit is in process of becoming ready
[24137.732586] sd 9:0:0:0: [sdf] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[24137.732588] print_req_error: I/O error, dev sdf, sector 0
[24137.732593] Buffer I/O error on dev sdf, logical block 0, async page read
[24287.783555] INFO: task kworker/u8:2:4129 blocked for more than 120 seconds.
[24287.783560]       Tainted: P           OE    4.15.0-112-generic #113-Ubuntu
[24287.783562] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[24287.783565] kworker/u8:2    D    0  4129      2 0x80000000
[24287.783573] Workqueue: events_unbound async_run_entry_fn
[24287.783574] Call Trace:
[24287.783580]  __schedule+0x24e/0x880
[24287.783583]  schedule+0x2c/0x80
[24287.783585]  io_schedule+0x16/0x40
[24287.783587]  do_read_cache_page+0x3b6/0x580
[24287.783591]  ? blkdev_writepages+0x40/0x40
[24287.783594]  ? page_cache_tree_insert+0xe0/0xe0
[24287.783597]  ? osf_partition+0x230/0x230
[24287.783598]  read_cache_page+0x15/0x20
[24287.783600]  read_dev_sector+0x2d/0xe0
[24287.783602]  sgi_partition+0x44/0x270
[24287.783604]  ? snprintf+0x45/0x70
[24287.783607]  check_partition+0x130/0x230
[24287.783609]  rescan_partitions+0xaa/0x350
[24287.783611]  bdev_disk_changed+0x53/0x60
[24287.783613]  __blkdev_get+0x34a/0x510
[24287.783615]  blkdev_get+0x129/0x320
[24287.783618]  ? wake_up_bit+0x42/0x50
[24287.783621]  ? unlock_new_inode+0x4c/0x80
[24287.783623]  ? bdget+0x108/0x120
[24287.783625]  device_add_disk+0x38b/0x490
[24287.783628]  ? __pm_runtime_use_autosuspend+0x54/0x70
[24287.783631]  sd_probe_async+0x102/0x230
[24287.783633]  async_run_entry_fn+0x3c/0x150
[24287.783636]  process_one_work+0x1de/0x420
[24287.783638]  worker_thread+0x32/0x410
[24287.783640]  kthread+0x121/0x140
[24287.783642]  ? process_one_work+0x420/0x420
[24287.783644]  ? kthread_create_worker_on_cpu+0x70/0x70
[24287.783646]  ret_from_fork+0x35/0x40
[24319.631486] sd 9:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[24319.631490] sd 9:0:0:0: [sdf] tag#0 Sense Key : Not Ready [current] 
[24319.631493] sd 9:0:0:0: [sdf] tag#0 Add. Sense: Logical unit is in process of becoming ready
[24319.631496] sd 9:0:0:0: [sdf] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[24319.631499] print_req_error: I/O error, dev sdf, sector 0
[24319.631505] Buffer I/O error on dev sdf, logical block 0, async page read
[24501.430544] sd 9:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[24501.430547] sd 9:0:0:0: [sdf] tag#0 Sense Key : Not Ready [current] 
[24501.430550] sd 9:0:0:0: [sdf] tag#0 Add. Sense: Logical unit is in process of becoming ready
[24501.430553] sd 9:0:0:0: [sdf] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[24501.430555] print_req_error: I/O error, dev sdf, sector 0
[24501.430561] Buffer I/O error on dev sdf, logical block 0, async page read
[24501.430574] ldm_validate_partition_table(): Disk read failed.
[24650.268350] INFO: task kworker/u8:2:4129 blocked for more than 120 seconds.
[24650.268356]       Tainted: P           OE    4.15.0-112-generic #113-Ubuntu
[24650.268358] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[24650.268360] kworker/u8:2    D    0  4129      2 0x80000000
[24650.268368] Workqueue: events_unbound async_run_entry_fn
[24650.268370] Call Trace:
[24650.268376]  __schedule+0x24e/0x880
[24650.268378]  schedule+0x2c/0x80
[24650.268380]  io_schedule+0x16/0x40
[24650.268383]  do_read_cache_page+0x3b6/0x580
[24650.268386]  ? blkdev_writepages+0x40/0x40
[24650.268389]  ? page_cache_tree_insert+0xe0/0xe0
[24650.268391]  read_cache_page+0x15/0x20
[24650.268394]  read_dev_sector+0x2d/0xe0
[24650.268396]  msdos_partition+0x6e/0xa70
[24650.268398]  ? osf_partition+0x230/0x230
[24650.268399]  ? read_cache_page+0x15/0x20
[24650.268401]  ? sgi_partition+0x44/0x270
[24650.268403]  ? snprintf+0x45/0x70
[24650.268406]  ? parse_unixware+0x1e0/0x1e0
[24650.268408]  check_partition+0x130/0x230
[24650.268410]  rescan_partitions+0xaa/0x350
[24650.268412]  bdev_disk_changed+0x53/0x60
[24650.268414]  __blkdev_get+0x34a/0x510
[24650.268416]  blkdev_get+0x129/0x320
[24650.268419]  ? wake_up_bit+0x42/0x50
[24650.268422]  ? unlock_new_inode+0x4c/0x80
[24650.268424]  ? bdget+0x108/0x120
[24650.268426]  device_add_disk+0x38b/0x490
[24650.268429]  ? __pm_runtime_use_autosuspend+0x54/0x70
[24650.268432]  sd_probe_async+0x102/0x230
[24650.268434]  async_run_entry_fn+0x3c/0x150
[24650.268437]  process_one_work+0x1de/0x420
[24650.268439]  worker_thread+0x32/0x410
[24650.268441]  kthread+0x121/0x140
[24650.268443]  ? process_one_work+0x420/0x420
[24650.268444]  ? kthread_create_worker_on_cpu+0x70/0x70
[24650.268447]  ret_from_fork+0x35/0x40
[24683.217972] sd 9:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[24683.217976] sd 9:0:0:0: [sdf] tag#0 Sense Key : Not Ready [current] 
[24683.217978] sd 9:0:0:0: [sdf] tag#0 Add. Sense: Logical unit is in process of becoming ready
[24683.217982] sd 9:0:0:0: [sdf] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[24683.217984] print_req_error: I/O error, dev sdf, sector 0
[24683.217989] Buffer I/O error on dev sdf, logical block 0, async page read
[24864.878574] sd 9:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[24864.878577] sd 9:0:0:0: [sdf] tag#0 Sense Key : Not Ready [current] 
[24864.878580] sd 9:0:0:0: [sdf] tag#0 Add. Sense: Logical unit is in process of becoming ready
[24864.878583] sd 9:0:0:0: [sdf] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[24864.878585] print_req_error: I/O error, dev sdf, sector 0
[24864.878591] Buffer I/O error on dev sdf, logical block 0, async page read
[25012.753517] INFO: task kworker/u8:2:4129 blocked for more than 120 seconds.
[25012.753522]       Tainted: P           OE    4.15.0-112-generic #113-Ubuntu
[25012.753524] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[25012.753526] kworker/u8:2    D    0  4129      2 0x80000000
[25012.753534] Workqueue: events_unbound async_run_entry_fn
[25012.753536] Call Trace:
[25012.753543]  __schedule+0x24e/0x880
[25012.753545]  schedule+0x2c/0x80
[25012.753547]  io_schedule+0x16/0x40
[25012.753549]  do_read_cache_page+0x3b6/0x580
[25012.753553]  ? blkdev_writepages+0x40/0x40
[25012.753556]  ? page_cache_tree_insert+0xe0/0xe0
[25012.753558]  read_cache_page+0x15/0x20
[25012.753560]  read_dev_sector+0x2d/0xe0
[25012.753562]  sun_partition+0x48/0x380
[25012.753564]  ? osf_partition+0x48/0x230
[25012.753566]  ? snprintf+0x45/0x70
[25012.753568]  ? sgi_partition+0x270/0x270
[25012.753570]  check_partition+0x130/0x230
[25012.753572]  rescan_partitions+0xaa/0x350
[25012.753575]  bdev_disk_changed+0x53/0x60
[25012.753577]  __blkdev_get+0x34a/0x510
[25012.753579]  blkdev_get+0x129/0x320
[25012.753582]  ? wake_up_bit+0x42/0x50
[25012.753584]  ? unlock_new_inode+0x4c/0x80
[25012.753586]  ? bdget+0x108/0x120
[25012.753589]  device_add_disk+0x38b/0x490
[25012.753591]  ? __pm_runtime_use_autosuspend+0x54/0x70
[25012.753594]  sd_probe_async+0x102/0x230
[25012.753596]  async_run_entry_fn+0x3c/0x150
[25012.753599]  process_one_work+0x1de/0x420
[25012.753601]  worker_thread+0x32/0x410
[25012.753603]  kthread+0x121/0x140
[25012.753605]  ? process_one_work+0x420/0x420
[25012.753607]  ? kthread_create_worker_on_cpu+0x70/0x70
[25012.753609]  ret_from_fork+0x35/0x40
[25046.677677] sd 9:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[25046.677680] sd 9:0:0:0: [sdf] tag#0 Sense Key : Not Ready [current] 
[25046.677683] sd 9:0:0:0: [sdf] tag#0 Add. Sense: Logical unit is in process of becoming ready
[25046.677686] sd 9:0:0:0: [sdf] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[25046.677688] print_req_error: I/O error, dev sdf, sector 0
[25046.677694] Buffer I/O error on dev sdf, logical block 0, async page read
[25228.476661] sd 9:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[25228.476664] sd 9:0:0:0: [sdf] tag#0 Sense Key : Not Ready [current] 
[25228.476667] sd 9:0:0:0: [sdf] tag#0 Add. Sense: Logical unit is in process of becoming ready
[25228.476670] sd 9:0:0:0: [sdf] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[25228.476672] print_req_error: I/O error, dev sdf, sector 0
[25228.476677] Buffer I/O error on dev sdf, logical block 0, async page read
[25228.476690] Dev sdf: unable to read RDB block 0
[25375.238861] INFO: task kworker/u8:2:4129 blocked for more than 120 seconds.
[25375.238867]       Tainted: P           OE    4.15.0-112-generic #113-Ubuntu
[25375.238869] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[25375.238871] kworker/u8:2    D    0  4129      2 0x80000000
[25375.238879] Workqueue: events_unbound async_run_entry_fn
[25375.238881] Call Trace:
[25375.238887]  __schedule+0x24e/0x880
[25375.238889]  schedule+0x2c/0x80
[25375.238891]  io_schedule+0x16/0x40
[25375.238894]  do_read_cache_page+0x3b6/0x580
[25375.238897]  ? blkdev_writepages+0x40/0x40
[25375.238900]  ? page_cache_tree_insert+0xe0/0xe0
[25375.238903]  ? amiga_partition+0x4f0/0x4f0
[25375.238905]  read_cache_page+0x15/0x20
[25375.238906]  read_dev_sector+0x2d/0xe0
[25375.238908]  atari_partition+0x64/0x8a0
[25375.238910]  ? ldm_ldmdb_add+0x866/0xd40
[25375.238912]  ? snprintf+0x45/0x70
[25375.238915]  ? amiga_partition+0x4f0/0x4f0
[25375.238916]  check_partition+0x130/0x230
[25375.238918]  rescan_partitions+0xaa/0x350
[25375.238921]  bdev_disk_changed+0x53/0x60
[25375.238923]  __blkdev_get+0x34a/0x510
[25375.238925]  blkdev_get+0x129/0x320
[25375.238928]  ? wake_up_bit+0x42/0x50
[25375.238931]  ? unlock_new_inode+0x4c/0x80
[25375.238933]  ? bdget+0x108/0x120
[25375.238935]  device_add_disk+0x38b/0x490
[25375.238938]  ? __pm_runtime_use_autosuspend+0x54/0x70
[25375.238940]  sd_probe_async+0x102/0x230
[25375.238943]  async_run_entry_fn+0x3c/0x150
[25375.238945]  process_one_work+0x1de/0x420
[25375.238948]  worker_thread+0x32/0x410
[25375.238949]  kthread+0x121/0x140
[25375.238951]  ? process_one_work+0x420/0x420
[25375.238953]  ? kthread_create_worker_on_cpu+0x70/0x70
[25375.238956]  ret_from_fork+0x35/0x40
[25410.275586] sd 9:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[25410.275590] sd 9:0:0:0: [sdf] tag#0 Sense Key : Not Ready [current] 
[25410.275592] sd 9:0:0:0: [sdf] tag#0 Add. Sense: Logical unit is in process of becoming ready
[25410.275595] sd 9:0:0:0: [sdf] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[25410.275598] print_req_error: I/O error, dev sdf, sector 0
[25410.275603] Buffer I/O error on dev sdf, logical block 0, async page read
[25592.124726] sd 9:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[25592.124730] sd 9:0:0:0: [sdf] tag#0 Sense Key : Not Ready [current] 
[25592.124732] sd 9:0:0:0: [sdf] tag#0 Add. Sense: Logical unit is in process of becoming ready
[25592.124736] sd 9:0:0:0: [sdf] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[25592.124738] print_req_error: I/O error, dev sdf, sector 0
[25592.124743] Buffer I/O error on dev sdf, logical block 0, async page read
[25773.973716] sd 9:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[25773.973720] sd 9:0:0:0: [sdf] tag#0 Sense Key : Not Ready [current] 
[25773.973723] sd 9:0:0:0: [sdf] tag#0 Add. Sense: Logical unit is in process of becoming ready
[25773.973726] sd 9:0:0:0: [sdf] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 18 00 00 00 08 00 00
[25773.973728] print_req_error: I/O error, dev sdf, sector 24
[25773.973734] Buffer I/O error on dev sdf, logical block 3, async page read
[25955.772882] sd 9:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[25955.772886] sd 9:0:0:0: [sdf] tag#0 Sense Key : Not Ready [current] 
[25955.772888] sd 9:0:0:0: [sdf] tag#0 Add. Sense: Logical unit is in process of becoming ready
[25955.772892] sd 9:0:0:0: [sdf] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[25955.772894] print_req_error: I/O error, dev sdf, sector 0
[25955.772900] Buffer I/O error on dev sdf, logical block 0, async page read
[26137.622000] sd 9:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[26137.622004] sd 9:0:0:0: [sdf] tag#0 Sense Key : Not Ready [current] 
[26137.622006] sd 9:0:0:0: [sdf] tag#0 Add. Sense: Logical unit is in process of becoming ready
[26137.622010] sd 9:0:0:0: [sdf] tag#0 CDB: Read(16) 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[26137.622012] print_req_error: I/O error, dev sdf, sector 0
[26137.622017] Buffer I/O error on dev sdf, logical block 0, async page read
[26137.622030]  sdf: unable to read partition table
[26137.627169] sd 9:0:0:0: [sdf] Spinning up disk...
[26138.645066] .
[26321.421022] sd 9:0:0:0: [sdf] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[26321.421026] sd 9:0:0:0: [sdf] tag#0 Sense Key : Not Ready [current] 
[26321.421028] sd 9:0:0:0: [sdf] tag#0 Add. Sense: Logical unit is in process of becoming ready
[26321.421032] sd 9:0:0:0: [sdf] tag#0 CDB: Read(16) 88 00 00 00 00 01 5d 4f 9f 80 00 00 00 08 00 00
[26321.421034] print_req_error: I/O error, dev sdf, sector 5860466560
[26322.432187] .
[26322.432189] not responding...
[26322.476612] sd 9:0:0:0: [sdf] Attached SCSI disk

geole · Le 28/08/2020, à 16:08

Dans la trace, cette ligne apparaît plusieurs fois
print_req_error: I/O error, dev sdf, sector 0
Alors, j'attends le rapport smartcl et ton verdict sur le montage du disque avec l'ordinateur 16.04 (pas le montage de hier) mais le montage que tu vas aussitôt que tu auras fini avec le smartctl.

Peux-tu donner le retour de cette commande

journalctl -b  | grep uas

Dernière modification par geole (Le 28/08/2020, à 16:13)

hunt · Le 28/08/2020, à 17:01

Alors sur la 18.04 :

christophe@christophe-System-Product-Name:~$ sudo smartctl   -s on   -a /dev/sdf[sudo] Mot de passe de christophe : 
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.15.0-112-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

Smartctl open device: /dev/sdf failed: No such device
christophe@christophe-System-Product-Name:~$ journalctl -b  | grep uas
août 28 08:09:39 christophe-System-Product-Name kernel: squashfs: version 4.0 (2009/01/31) Phillip Lougher
août 28 08:09:39 christophe-System-Product-Name kernel: usbcore: registered new interface driver uas
christophe@christophe-System-Product-Name:~$

Et je vais voir maintenant sur la 16.04, je reviens

hunt · Le 28/08/2020, à 17:08

Voilà suis sur la 16.04, aussitôt branché, aussitôt reconnu, les sauvegardes sont toujours présentes et opérationnelles...

Pour comparer les messages si besoin :

christophe@christophe-2:~$ journalctl -b  | grep uas
août 28 07:48:14 christophe-2 kernel: squashfs: version 4.0 (2009/01/31) Phillip Lougher
août 28 18:02:39 christophe-2 kernel: usbcore: registered new interface driver uas
christophe@christophe-2:~$

christophe@christophe-2:~$ dmesg -w
[    0.000000] microcode: CPU0 microcode updated early to revision 0xa0b, date = 2010-09-28
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.4.0-187-generic (buildd@lgw01-amd64-035) (gcc version 5.4.0 20160609 (Ubuntu 5.4.0-6ubuntu1~16.04.12) ) #217-Ubuntu SMP Tue Jul 21 04:18:15 UTC 2020 (Ubuntu 4.4.0-187.217-generic 4.4.230)
[    0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-4.4.0-187-generic root=UUID=5d831733-ffe2-4c3e-b36c-66c84933750b ro quiet splash
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   Centaur CentaurHauls
[    0.000000] x86/fpu: Supporting XSAVE feature 0x01: 'x87 floating point registers'
[    0.000000] x86/fpu: Supporting XSAVE feature 0x02: 'SSE registers'
[    0.000000] x86/fpu: Enabled xstate features 0x3, context size is 576 bytes, using 'standard' format.
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x0000000000097bff] usable
[    0.000000] BIOS-e820: [mem 0x0000000000097c00-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000e8000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000e6fc1d9f] usable
[    0.000000] BIOS-e820: [mem 0x00000000e6fc1da0-0x00000000e6fc1dff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000e6fc1e00-0x00000000e7ffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000f4000000-0x00000000f7ffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fed3ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed45000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x0000000217ffffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.6 present.
[    0.000000] DMI: Hewlett-Packard HP xw4600 Workstation/0AA0h, BIOS 786F3 v01.17 07/29/2009
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] e820: last_pfn = 0x218000 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-E3FFF write-protect
[    0.000000]   E4000-EFFFF write-back
[    0.000000]   F0000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask E00000000 write-back
[    0.000000]   1 base 0E8000000 mask FF8000000 uncachable
[    0.000000]   2 base 0F0000000 mask FF0000000 uncachable
[    0.000000]   3 base 218000000 mask FF8000000 uncachable
[    0.000000]   4 base 200000000 mask FE0000000 write-back
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WC  UC- WT  
[    0.000000] original variable MTRRs
[    0.000000] reg 0, base: 0GB, range: 8GB, type WB
[    0.000000] reg 1, base: 3712MB, range: 128MB, type UC
[    0.000000] reg 2, base: 3840MB, range: 256MB, type UC
[    0.000000] reg 3, base: 8576MB, range: 128MB, type UC
[    0.000000] reg 4, base: 8GB, range: 512MB, type WB
[    0.000000] total RAM covered: 8192M
[    0.000000] Found optimal setting for mtrr clean up
[    0.000000]  gran_size: 64K 	chunk_size: 512M 	num_reg: 6  	lose cover RAM: 0G
[    0.000000] New variable MTRRs
[    0.000000] reg 0, base: 0GB, range: 4GB, type WB
[    0.000000] reg 1, base: 3712MB, range: 128MB, type UC
[    0.000000] reg 2, base: 3840MB, range: 256MB, type UC
[    0.000000] reg 3, base: 4GB, range: 4GB, type WB
[    0.000000] reg 4, base: 8GB, range: 512MB, type WB
[    0.000000] reg 5, base: 8576MB, range: 128MB, type UC
[    0.000000] e820: update [mem 0xe8000000-0xffffffff] usable ==> reserved
[    0.000000] e820: last_pfn = 0xe6fc1 max_arch_pfn = 0x400000000
[    0.000000] found SMP MP-table at [mem 0x000f9bf0-0x000f9bff] mapped at [ffff8800000f9bf0]
[    0.000000] Scanning 1 areas for low memory corruption
[    0.000000] Base memory trampoline at [ffff880000090000] 90000 size 28672
[    0.000000] RAMDISK: [mem 0x33180000-0x358b7fff]
[    0.000000] ACPI: Early table checksum verification disabled
[    0.000000] ACPI: RSDP 0x00000000000E6410 000024 (v02 COMPAQ)
[    0.000000] ACPI: XSDT 0x00000000E6FC1EE8 000064 (v01 HPQOEM SLIC-WKS 20090729      00000000)
[    0.000000] ACPI: FACP 0x00000000E6FC2088 0000F4 (v03 COMPAQ          E6FC2647      00000000)
[    0.000000] ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/Pm1aEventBlock: 32/16 (20150930/tbfadt-623)
[    0.000000] ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/Gpe0Block: 128/32 (20150930/tbfadt-623)
[    0.000000] ACPI BIOS Warning (bug): Invalid length for FADT/Pm1aEventBlock: 16, using default 32 (20150930/tbfadt-704)
[    0.000000] ACPI: DSDT 0x00000000E6FC2647 0098EC (v01 COMPAQ DSDT_PRJ 00000001 MSFT 0100000E)
[    0.000000] ACPI: FACS 0x00000000E6FC1E00 000040
[    0.000000] ACPI: FACS 0x00000000E6FC1E00 000040
[    0.000000] ACPI: APIC 0x00000000E6FC217C 000084 (v01 COMPAQ BEARLX38 00000001      00000000)
[    0.000000] ACPI: ASF! 0x00000000E6FC2200 000063 (v32 COMPAQ BEARLX38 00000001      00000000)
[    0.000000] ACPI: MCFG 0x00000000E6FC2263 00003C (v01 COMPAQ BEARLX38 00000001      00000000)
[    0.000000] ACPI: TCPA 0x00000000E6FC229F 000032 (v01 COMPAQ BEARLX38 00000001      00000000)
[    0.000000] ACPI: SLIC 0x00000000E6FC22D1 000176 (v01 HPQOEM SLIC-WKS 00000001      00000000)
[    0.000000] ACPI: HPET 0x00000000E6FC2447 000038 (v01 COMPAQ BEARLX38 00000001      00000000)
[    0.000000] ACPI: DMAR 0x00000000E6FC247F 000158 (v01 COMPAQ BEARLX38 00000001      00000000)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at [mem 0x0000000000000000-0x0000000217ffffff]
[    0.000000] NODE_DATA(0) allocated [mem 0x217ff5000-0x217ff9fff]
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000001000-0x0000000000ffffff]
[    0.000000]   DMA32    [mem 0x0000000001000000-0x00000000ffffffff]
[    0.000000]   Normal   [mem 0x0000000100000000-0x0000000217ffffff]
[    0.000000]   Device   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000001000-0x0000000000096fff]
[    0.000000]   node   0: [mem 0x0000000000100000-0x00000000e6fc0fff]
[    0.000000]   node   0: [mem 0x0000000100000000-0x0000000217ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x0000000217ffffff]
[    0.000000] On node 0 totalpages: 2092887
[    0.000000]   DMA zone: 64 pages used for memmap
[    0.000000]   DMA zone: 22 pages reserved
[    0.000000]   DMA zone: 3990 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 14720 pages used for memmap
[    0.000000]   DMA32 zone: 942017 pages, LIFO batch:31
[    0.000000]   Normal zone: 17920 pages used for memmap
[    0.000000]   Normal zone: 1146880 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0xf808
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
[    0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] smpboot: Allowing 4 CPUs, 2 hotplug CPUs
[    0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[    0.000000] PM: Registered nosave memory: [mem 0x00097000-0x00097fff]
[    0.000000] PM: Registered nosave memory: [mem 0x00098000-0x0009ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000e7fff]
[    0.000000] PM: Registered nosave memory: [mem 0x000e8000-0x000fffff]
[    0.000000] PM: Registered nosave memory: [mem 0xe6fc1000-0xe6fc1fff]
[    0.000000] PM: Registered nosave memory: [mem 0xe6fc1000-0xe6fc1fff]
[    0.000000] PM: Registered nosave memory: [mem 0xe6fc2000-0xe7ffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xe8000000-0xf3ffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xf4000000-0xf7ffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfebfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfed3ffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed40000-0xfed44fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed45000-0xffffffff]
[    0.000000] e820: [mem 0xe8000000-0xf3ffffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
[    0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:4 nr_node_ids:1
[    0.000000] PERCPU: Embedded 33 pages/cpu @ffff880217c00000 s95512 r8192 d31464 u524288
[    0.000000] pcpu-alloc: s95512 r8192 d31464 u524288 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3 
[    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total pages: 2060161
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.4.0-187-generic root=UUID=5d831733-ffe2-4c3e-b36c-66c84933750b ro quiet splash
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Calgary: detecting Calgary via BIOS EBDA area
[    0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.000000] DMAR: [Firmware Bug]: Your BIOS is broken; DMAR reported at address fed90000 returns all ones!
               BIOS vendor: Hewlett-Packard; Ver: 786F3 v01.17; Product Version: 
[    0.000000] Memory: 8114820K/8371548K available (8636K kernel code, 1337K rwdata, 4040K rodata, 1492K init, 1296K bss, 256728K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Kernel/User page tables isolation: enabled
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	Build-time adjustment of leaf fanout to 64.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=4.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[    0.000000] NR_IRQS:33024 nr_irqs:456 16
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484882848 ns
[    0.000000] hpet clockevent registered
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] tsc: Detected 3000.176 MHz processor
[    0.004011] Calibrating delay loop (skipped), value calculated using timer frequency.. 6000.35 BogoMIPS (lpj=12000704)
[    0.004013] pid_max: default: 32768 minimum: 301
[    0.004020] ACPI: Core revision 20150930
[    0.009851] ACPI: 1 ACPI AML tables successfully acquired and loaded
[    0.009872] Security Framework initialized
[    0.009875] Yama: becoming mindful.
[    0.009896] AppArmor: AppArmor initialized
[    0.010412] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[    0.013526] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.014987] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
[    0.014997] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes)
[    0.015324] Initializing cgroup subsys io
[    0.015329] Initializing cgroup subsys memory
[    0.015339] Initializing cgroup subsys devices
[    0.015343] Initializing cgroup subsys freezer
[    0.015346] Initializing cgroup subsys net_cls
[    0.015349] Initializing cgroup subsys perf_event
[    0.015351] Initializing cgroup subsys net_prio
[    0.015356] Initializing cgroup subsys hugetlb
[    0.015358] Initializing cgroup subsys pids
[    0.015380] mce: CPU supports 6 MCE banks
[    0.015390] CPU0: Thermal monitoring enabled (TM2)
[    0.015395] process: using mwait in idle threads
[    0.015399] Last level iTLB entries: 4KB 128, 2MB 4, 4MB 4
[    0.015401] Last level dTLB entries: 4KB 256, 2MB 0, 4MB 32, 1GB 0
[    0.015403] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization
[    0.015405] Spectre V2 : Mitigation: Full generic retpoline
[    0.015406] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[    0.015407] Speculative Store Bypass: Vulnerable
[    0.015439] MDS: Vulnerable: Clear CPU buffers attempted, no microcode
[    0.015812] Freeing SMP alternatives memory: 36K
[    0.019963] ftrace: allocating 32337 entries in 127 pages
[    0.036096] smpboot: APIC(0) Converting physical 0 to logical package 0
[    0.036099] smpboot: Max logical packages: 2
[    0.036104] DMAR: Host address width 36
[    0.036106] DMAR: DRHD base: 0x000000fed90000 flags: 0x0
[    0.036118] DMAR: Failed to map dmar0
[    0.036153] DMAR: Parse DMAR table failure.
[    0.036486] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.187377] smpboot: CPU0: Intel(R) Core(TM)2 Duo CPU     E8400  @ 3.00GHz (family: 0x6, model: 0x17, stepping: 0xa)
[    0.187391] Performance Events: PEBS fmt0+, 4-deep LBR, Core2 events, Intel PMU driver.
[    0.187398] ... version:                2
[    0.187400] ... bit width:              40
[    0.187401] ... generic registers:      2
[    0.187402] ... value mask:             000000ffffffffff
[    0.187403] ... max period:             000000007fffffff
[    0.187404] ... fixed-purpose events:   3
[    0.187406] ... event mask:             0000000700000003
[    0.188000] x86: Booting SMP configuration:
[    0.188000] .... node  #0, CPUs:      #1
[    0.008000] microcode: CPU1 microcode updated early to revision 0xa0b, date = 2010-09-28
[    0.192040] x86: Booted up 1 node, 2 CPUs
[    0.192046] smpboot: Total of 2 processors activated (12000.70 BogoMIPS)
[    0.194678] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[    0.194694] devtmpfs: initialized
[    0.197969] evm: security.selinux
[    0.197971] evm: security.SMACK64
[    0.197972] evm: security.SMACK64EXEC
[    0.197973] evm: security.SMACK64TRANSMUTE
[    0.197974] evm: security.SMACK64MMAP
[    0.197976] evm: security.ima
[    0.197977] evm: security.capability
[    0.198033] PM: Registering ACPI NVS region [mem 0xe6fc1da0-0xe6fc1dff] (96 bytes)
[    0.198102] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.198113] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.198191] pinctrl core: initialized pinctrl subsystem
[    0.198311] RTC time:  5:48:09, date: 08/28/20
[    0.198430] NET: Registered protocol family 16
[    0.208006] cpuidle: using governor ladder
[    0.216004] cpuidle: using governor menu
[    0.216009] PCCT header not found.
[    0.216073] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[    0.216076] ACPI: bus type PCI registered
[    0.216078] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.216170] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf4000000-0xf7ffffff] (base 0xf4000000)
[    0.216174] PCI: MMCONFIG at [mem 0xf4000000-0xf7ffffff] reserved in E820
[    0.216182] pmd_set_huge: Cannot satisfy [mem 0xf4000000-0xf4200000] with a huge-page mapping due to MTRR override.
[    0.216324] PCI: Using configuration type 1 for base access
[    0.224087] ACPI: Added _OSI(Module Device)
[    0.224089] ACPI: Added _OSI(Processor Device)
[    0.224091] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.224092] ACPI: Added _OSI(Processor Aggregator Device)
[    0.229506] ACPI: Dynamic OEM Table Load:
[    0.229511] ACPI: SSDT 0xFFFF88020DCD6C00 00017C (v01 COMPAQ CST      00000001 MSFT 0100000E)
[    0.229804] ACPI: Interpreter enabled
[    0.229819] ACPI: (supports S0 S3 S4 S5)
[    0.229821] ACPI: Using IOAPIC for interrupt routing
[    0.229840] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.236328] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.236334] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    0.236338] ACPI BIOS Error (bug): \_SB_.PCI0._OSC: Excess arguments - ASL declared 5, ACPI requires 4 (20150930/nsarguments-189)
[    0.236377] ACPI Error: [CAPD] Namespace lookup failure, AE_ALREADY_EXISTS (20150930/dsfield-211)
[    0.236382] ACPI Error: Method parse/execution failed [\_SB.PCI0._OSC] (Node ffff88020f1b1af0), AE_ALREADY_EXISTS (20150930/psparse-542)
[    0.236390] acpi PNP0A08:00: _OSC failed (AE_ALREADY_EXISTS); disabling ASPM
[    0.236399] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
[    0.236631] PCI host bridge to bus 0000:00
[    0.236634] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xfebfffff window]
[    0.236636] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7 window]
[    0.236638] pci_bus 0000:00: root bus resource [io  0x1000-0x2fff window]
[    0.236640] pci_bus 0000:00: root bus resource [io  0x3000-0x6fff window]
[    0.236642] pci_bus 0000:00: root bus resource [io  0x7000-0xafff window]
[    0.236644] pci_bus 0000:00: root bus resource [io  0xb000-0xffff window]
[    0.236646] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    0.236648] pci_bus 0000:00: root bus resource [mem 0xe8000000-0xf3ffffff window]
[    0.236650] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.236658] pci 0000:00:00.0: [8086:29e0] type 00 class 0x060000
[    0.236744] pci 0000:00:01.0: [8086:29e1] type 01 class 0x060400
[    0.236776] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.236810] pci 0000:00:01.0: System wakeup disabled by ACPI
[    0.236854] pci 0000:00:06.0: [8086:29e9] type 01 class 0x060400
[    0.236884] pci 0000:00:06.0: PME# supported from D0 D3hot D3cold
[    0.236916] pci 0000:00:06.0: System wakeup disabled by ACPI
[    0.236970] pci 0000:00:1a.0: [8086:2937] type 00 class 0x0c0300
[    0.237011] pci 0000:00:1a.0: reg 0x20: [io  0x2100-0x211f]
[    0.237068] pci 0000:00:1a.0: System wakeup disabled by ACPI
[    0.237108] pci 0000:00:1a.1: [8086:2938] type 00 class 0x0c0300
[    0.237149] pci 0000:00:1a.1: reg 0x20: [io  0x2120-0x213f]
[    0.237205] pci 0000:00:1a.1: System wakeup disabled by ACPI
[    0.237245] pci 0000:00:1a.2: [8086:2939] type 00 class 0x0c0300
[    0.237286] pci 0000:00:1a.2: reg 0x20: [io  0x2140-0x215f]
[    0.237343] pci 0000:00:1a.2: System wakeup disabled by ACPI
[    0.237390] pci 0000:00:1a.7: [8086:293c] type 00 class 0x0c0320
[    0.237415] pci 0000:00:1a.7: reg 0x10: [mem 0xf3204800-0xf3204bff]
[    0.237479] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[    0.237513] pci 0000:00:1a.7: System wakeup disabled by ACPI
[    0.237557] pci 0000:00:1b.0: [8086:293e] type 00 class 0x040300
[    0.237580] pci 0000:00:1b.0: reg 0x10: [mem 0xf3200000-0xf3203fff 64bit]
[    0.237634] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.237704] pci 0000:00:1c.0: [8086:2940] type 01 class 0x060400
[    0.237762] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.237799] pci 0000:00:1c.0: System wakeup disabled by ACPI
[    0.237844] pci 0000:00:1c.4: [8086:2948] type 01 class 0x060400
[    0.237902] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[    0.237939] pci 0000:00:1c.4: System wakeup disabled by ACPI
[    0.237980] pci 0000:00:1c.5: [8086:294a] type 01 class 0x060400
[    0.238039] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
[    0.238076] pci 0000:00:1c.5: System wakeup disabled by ACPI
[    0.238117] pci 0000:00:1d.0: [8086:2934] type 00 class 0x0c0300
[    0.238158] pci 0000:00:1d.0: reg 0x20: [io  0x2160-0x217f]
[    0.238214] pci 0000:00:1d.0: System wakeup disabled by ACPI
[    0.238255] pci 0000:00:1d.1: [8086:2935] type 00 class 0x0c0300
[    0.238296] pci 0000:00:1d.1: reg 0x20: [io  0x2180-0x219f]
[    0.238354] pci 0000:00:1d.1: System wakeup disabled by ACPI
[    0.238394] pci 0000:00:1d.2: [8086:2936] type 00 class 0x0c0300
[    0.238434] pci 0000:00:1d.2: reg 0x20: [io  0x21a0-0x21bf]
[    0.238490] pci 0000:00:1d.2: System wakeup disabled by ACPI
[    0.238536] pci 0000:00:1d.7: [8086:293a] type 00 class 0x0c0320
[    0.238561] pci 0000:00:1d.7: reg 0x10: [mem 0xf3204c00-0xf3204fff]
[    0.238625] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.238661] pci 0000:00:1d.7: System wakeup disabled by ACPI
[    0.238703] pci 0000:00:1e.0: [8086:244e] type 01 class 0x060401
[    0.238772] pci 0000:00:1e.0: System wakeup disabled by ACPI
[    0.238815] pci 0000:00:1f.0: [8086:2916] type 00 class 0x060100
[    0.238891] pci 0000:00:1f.0: quirk: [io  0xf800-0xf87f] claimed by ICH6 ACPI/GPIO/TCO
[    0.238895] pci 0000:00:1f.0: quirk: [io  0xfa00-0xfa3f] claimed by ICH6 GPIO
[    0.238899] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0400 (mask 007f)
[    0.238902] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0480 (mask 000f)
[    0.238905] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 0cb0 (mask 000f)
[    0.238986] pci 0000:00:1f.2: [8086:2822] type 00 class 0x010400
[    0.239007] pci 0000:00:1f.2: reg 0x10: [io  0x2200-0x2207]
[    0.239013] pci 0000:00:1f.2: reg 0x14: [io  0x2210-0x2213]
[    0.239020] pci 0000:00:1f.2: reg 0x18: [io  0x2208-0x220f]
[    0.239027] pci 0000:00:1f.2: reg 0x1c: [io  0x2214-0x2217]
[    0.239034] pci 0000:00:1f.2: reg 0x20: [io  0x21c0-0x21df]
[    0.239041] pci 0000:00:1f.2: reg 0x24: [mem 0xf3204000-0xf32047ff]
[    0.239069] pci 0000:00:1f.2: PME# supported from D3hot
[    0.239188] pci 0000:01:00.0: [10de:128b] type 00 class 0x030000
[    0.239205] pci 0000:01:00.0: reg 0x10: [mem 0xf2000000-0xf2ffffff]
[    0.239214] pci 0000:01:00.0: reg 0x14: [mem 0xe8000000-0xefffffff 64bit pref]
[    0.239223] pci 0000:01:00.0: reg 0x1c: [mem 0xf0000000-0xf1ffffff 64bit pref]
[    0.239229] pci 0000:01:00.0: reg 0x24: [io  0x1100-0x117f]
[    0.239236] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0007ffff pref]
[    0.239311] pci 0000:01:00.1: [10de:0e0f] type 00 class 0x040300
[    0.239327] pci 0000:01:00.1: reg 0x10: [mem 0xf3000000-0xf3003fff]
[    0.239425] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.239428] pci 0000:00:01.0:   bridge window [io  0x1000-0x1fff]
[    0.239430] pci 0000:00:01.0:   bridge window [mem 0xf2000000-0xf30fffff]
[    0.239434] pci 0000:00:01.0:   bridge window [mem 0xe8000000-0xf1ffffff 64bit pref]
[    0.239491] pci 0000:08:00.0: [1106:3483] type 00 class 0x0c0330
[    0.239513] pci 0000:08:00.0: reg 0x10: [mem 0xf3300000-0xf3300fff 64bit]
[    0.239562] pci 0000:08:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.239621] pci 0000:00:06.0: PCI bridge to [bus 08]
[    0.239624] pci 0000:00:06.0:   bridge window [mem 0xf3300000-0xf33fffff]
[    0.239685] pci 0000:00:1c.0: PCI bridge to [bus 28]
[    0.239748] pci 0000:00:1c.4: PCI bridge to [bus 34]
[    0.239829] pci 0000:3f:00.0: [14e4:167b] type 00 class 0x020000
[    0.239873] pci 0000:3f:00.0: reg 0x10: [mem 0xf3100000-0xf310ffff 64bit]
[    0.239980] pci 0000:3f:00.0: PME# supported from D3hot D3cold
[    0.248017] pci 0000:00:1c.5: PCI bridge to [bus 3f]
[    0.248024] pci 0000:00:1c.5:   bridge window [mem 0xf3100000-0xf31fffff]
[    0.248184] pci 0000:00:1e.0: PCI bridge to [bus 10] (subtractive decode)
[    0.248195] pci 0000:00:1e.0:   bridge window [mem 0xf8000000-0xfebfffff window] (subtractive decode)
[    0.248198] pci 0000:00:1e.0:   bridge window [io  0x0000-0x0cf7 window] (subtractive decode)
[    0.248201] pci 0000:00:1e.0:   bridge window [io  0x1000-0x2fff window] (subtractive decode)
[    0.248204] pci 0000:00:1e.0:   bridge window [io  0x3000-0x6fff window] (subtractive decode)
[    0.248207] pci 0000:00:1e.0:   bridge window [io  0x7000-0xafff window] (subtractive decode)
[    0.248215] pci 0000:00:1e.0:   bridge window [io  0xb000-0xffff window] (subtractive decode)
[    0.248217] pci 0000:00:1e.0:   bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode)
[    0.248219] pci 0000:00:1e.0:   bridge window [mem 0xe8000000-0xf3ffffff window] (subtractive decode)
[    0.248649] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 14 15)
[    0.248700] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 14 15)
[    0.248749] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11 14 15)
[    0.248798] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
[    0.248850] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 *11 14 15)
[    0.248900] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 14 15)
[    0.248949] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *10 11 14 15)
[    0.248997] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
[    0.249607] vgaarb: setting as boot device: PCI:0000:01:00.0
[    0.249607] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.249607] vgaarb: loaded
[    0.249607] vgaarb: bridge control possible 0000:01:00.0
[    0.249607] SCSI subsystem initialized
[    0.249607] libata version 3.00 loaded.
[    0.249607] ACPI: bus type USB registered
[    0.249607] usbcore: registered new interface driver usbfs
[    0.249607] usbcore: registered new interface driver hub
[    0.249607] usbcore: registered new device driver usb
[    0.249607] PCI: Using ACPI for IRQ routing
[    0.249607] PCI: pci_cache_line_size set to 64 bytes
[    0.249607] e820: reserve RAM buffer [mem 0x00097c00-0x0009ffff]
[    0.249607] e820: reserve RAM buffer [mem 0xe6fc1da0-0xe7ffffff]
[    0.249607] NetLabel: Initializing
[    0.249607] NetLabel:  domain hash size = 128
[    0.249607] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.249607] NetLabel:  unlabeled traffic allowed by default
[    0.249607] HPET: 4 timers in total, 0 timers will be used for per-cpu timer
[    0.249607] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[    0.249607] hpet0: 4 comparators, 64-bit 14.318180 MHz counter
[    0.253011] amd_nb: Cannot enumerate AMD northbridges
[    0.253011] clocksource: Switched to clocksource hpet
[    0.259472] AppArmor: AppArmor Filesystem Enabled
[    0.259551] pnp: PnP ACPI init
[    0.259626] pnp 00:00: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.259656] pnp 00:01: Plug and Play ACPI device, IDs PNP0f13 PNP0f0e (active)
[    0.259683] pnp 00:02: Plug and Play ACPI device, IDs PNP0303 (active)
[    0.259893] pnp 00:03: [dma 3]
[    0.259954] pnp 00:03: Plug and Play ACPI device, IDs PNP0401 (active)
[    0.260171] pnp 00:04: Plug and Play ACPI device, IDs PNP0501 PNP0500 (active)
[    0.260303] pnp 00:05: [dma 2]
[    0.260331] pnp 00:05: Plug and Play ACPI device, IDs PNP0700 (active)
[    0.260539] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.260560] pnp 00:07: disabling [io  0xf800-0xf81f] because it overlaps 0000:00:1f.0 BAR 13 [io  0xf800-0xf87f]
[    0.260563] pnp 00:07: disabling [io  0xf820-0xf83f] because it overlaps 0000:00:1f.0 BAR 13 [io  0xf800-0xf87f]
[    0.260565] pnp 00:07: disabling [io  0xf840-0xf85f] because it overlaps 0000:00:1f.0 BAR 13 [io  0xf800-0xf87f]
[    0.260568] pnp 00:07: disabling [io  0xf860-0xf87f] because it overlaps 0000:00:1f.0 BAR 13 [io  0xf800-0xf87f]
[    0.260601] system 00:07: [io  0x0400-0x041f] has been reserved
[    0.260603] system 00:07: [io  0x0420-0x043f] has been reserved
[    0.260605] system 00:07: [io  0x0440-0x045f] has been reserved
[    0.260608] system 00:07: [io  0x0460-0x047f] has been reserved
[    0.260610] system 00:07: [io  0x0480-0x048f] has been reserved
[    0.260612] system 00:07: [io  0xfa00-0xfa3f] has been reserved
[    0.260615] system 00:07: [io  0xfc00-0xfc7f] has been reserved
[    0.260617] system 00:07: [io  0xfc80-0xfcff] has been reserved
[    0.260619] system 00:07: [io  0xfe00-0xfe7f] has been reserved
[    0.260621] system 00:07: [io  0xfe80-0xfeff] has been reserved
[    0.260625] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.260676] system 00:08: [io  0x04d0-0x04d1] has been reserved
[    0.260679] system 00:08: [io  0x0cb0-0x0cbf] has been reserved
[    0.260682] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.260911] system 00:09: [mem 0x00000000-0x0009ffff] could not be reserved
[    0.260914] system 00:09: [mem 0x00100000-0xe7ffffff] could not be reserved
[    0.260916] system 00:09: [mem 0x000e4000-0x000fffff] could not be reserved
[    0.260919] system 00:09: [mem 0xfec01000-0xfecfffff] has been reserved
[    0.260921] system 00:09: [mem 0xfed00400-0xfed3ffff] has been reserved
[    0.260923] system 00:09: [mem 0xfed40000-0xffffffff] could not be reserved
[    0.260926] system 00:09: [mem 0xf4000000-0xf7ffffff] has been reserved
[    0.260928] system 00:09: [mem 0x000d1400-0x000e3fff] could not be reserved
[    0.260931] system 00:09: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.260939] pnp: PnP ACPI: found 10 devices
[    0.267456] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    0.267478] pci 0000:00:1c.0: bridge window [io  0x1000-0x0fff] to [bus 28] add_size 1000
[    0.267481] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 28] add_size 200000 add_align 100000
[    0.267484] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 28] add_size 200000 add_align 100000
[    0.267491] pci 0000:00:1c.4: bridge window [io  0x1000-0x0fff] to [bus 34] add_size 1000
[    0.267493] pci 0000:00:1c.4: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 34] add_size 200000 add_align 100000
[    0.267496] pci 0000:00:1c.4: bridge window [mem 0x00100000-0x000fffff] to [bus 34] add_size 200000 add_align 100000
[    0.267503] pci 0000:00:1c.5: bridge window [io  0x1000-0x0fff] to [bus 3f] add_size 1000
[    0.267506] pci 0000:00:1c.5: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 3f] add_size 200000 add_align 100000
[    0.267516] pci 0000:00:1c.0: res[14]=[mem 0x00100000-0x000fffff] res_to_dev_res add_size 200000 min_align 100000
[    0.267518] pci 0000:00:1c.0: res[14]=[mem 0x00100000-0x002fffff] res_to_dev_res add_size 200000 min_align 100000
[    0.267521] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] res_to_dev_res add_size 200000 min_align 100000
[    0.267523] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x002fffff 64bit pref] res_to_dev_res add_size 200000 min_align 100000
[    0.267526] pci 0000:00:1c.4: res[14]=[mem 0x00100000-0x000fffff] res_to_dev_res add_size 200000 min_align 100000
[    0.267528] pci 0000:00:1c.4: res[14]=[mem 0x00100000-0x002fffff] res_to_dev_res add_size 200000 min_align 100000
[    0.267531] pci 0000:00:1c.4: res[15]=[mem 0x00100000-0x000fffff 64bit pref] res_to_dev_res add_size 200000 min_align 100000
[    0.267533] pci 0000:00:1c.4: res[15]=[mem 0x00100000-0x002fffff 64bit pref] res_to_dev_res add_size 200000 min_align 100000
[    0.267536] pci 0000:00:1c.5: res[15]=[mem 0x00100000-0x000fffff 64bit pref] res_to_dev_res add_size 200000 min_align 100000
[    0.267538] pci 0000:00:1c.5: res[15]=[mem 0x00100000-0x002fffff 64bit pref] res_to_dev_res add_size 200000 min_align 100000
[    0.267541] pci 0000:00:1c.0: res[13]=[io  0x1000-0x0fff] res_to_dev_res add_size 1000 min_align 1000
[    0.267543] pci 0000:00:1c.0: res[13]=[io  0x1000-0x1fff] res_to_dev_res add_size 1000 min_align 1000
[    0.267545] pci 0000:00:1c.4: res[13]=[io  0x1000-0x0fff] res_to_dev_res add_size 1000 min_align 1000
[    0.267548] pci 0000:00:1c.4: res[13]=[io  0x1000-0x1fff] res_to_dev_res add_size 1000 min_align 1000
[    0.267550] pci 0000:00:1c.5: res[13]=[io  0x1000-0x0fff] res_to_dev_res add_size 1000 min_align 1000
[    0.267552] pci 0000:00:1c.5: res[13]=[io  0x1000-0x1fff] res_to_dev_res add_size 1000 min_align 1000
[    0.267557] pci 0000:00:1c.0: BAR 14: assigned [mem 0xf8000000-0xf81fffff]
[    0.267561] pci 0000:00:1c.0: BAR 15: assigned [mem 0xf8200000-0xf83fffff 64bit pref]
[    0.267564] pci 0000:00:1c.4: BAR 14: assigned [mem 0xf8400000-0xf85fffff]
[    0.267567] pci 0000:00:1c.4: BAR 15: assigned [mem 0xf8600000-0xf87fffff 64bit pref]
[    0.267571] pci 0000:00:1c.5: BAR 15: assigned [mem 0xf8800000-0xf89fffff 64bit pref]
[    0.267574] pci 0000:00:1c.0: BAR 13: assigned [io  0x3000-0x3fff]
[    0.267577] pci 0000:00:1c.4: BAR 13: assigned [io  0x4000-0x4fff]
[    0.267580] pci 0000:00:1c.5: BAR 13: assigned [io  0x5000-0x5fff]
[    0.267584] pci 0000:01:00.0: BAR 6: assigned [mem 0xf3080000-0xf30fffff pref]
[    0.267586] pci 0000:00:01.0: PCI bridge to [bus 01]
[    0.267589] pci 0000:00:01.0:   bridge window [io  0x1000-0x1fff]
[    0.267592] pci 0000:00:01.0:   bridge window [mem 0xf2000000-0xf30fffff]
[    0.267595] pci 0000:00:01.0:   bridge window [mem 0xe8000000-0xf1ffffff 64bit pref]
[    0.267598] pci 0000:00:06.0: PCI bridge to [bus 08]
[    0.267602] pci 0000:00:06.0:   bridge window [mem 0xf3300000-0xf33fffff]
[    0.267606] pci 0000:00:1c.0: PCI bridge to [bus 28]
[    0.267609] pci 0000:00:1c.0:   bridge window [io  0x3000-0x3fff]
[    0.267613] pci 0000:00:1c.0:   bridge window [mem 0xf8000000-0xf81fffff]
[    0.267616] pci 0000:00:1c.0:   bridge window [mem 0xf8200000-0xf83fffff 64bit pref]
[    0.267621] pci 0000:00:1c.4: PCI bridge to [bus 34]
[    0.267624] pci 0000:00:1c.4:   bridge window [io  0x4000-0x4fff]
[    0.267628] pci 0000:00:1c.4:   bridge window [mem 0xf8400000-0xf85fffff]
[    0.267632] pci 0000:00:1c.4:   bridge window [mem 0xf8600000-0xf87fffff 64bit pref]
[    0.267637] pci 0000:00:1c.5: PCI bridge to [bus 3f]
[    0.267640] pci 0000:00:1c.5:   bridge window [io  0x5000-0x5fff]
[    0.267644] pci 0000:00:1c.5:   bridge window [mem 0xf3100000-0xf31fffff]
[    0.267647] pci 0000:00:1c.5:   bridge window [mem 0xf8800000-0xf89fffff 64bit pref]
[    0.267652] pci 0000:00:1e.0: PCI bridge to [bus 10]
[    0.267662] pci_bus 0000:00: resource 4 [mem 0xf8000000-0xfebfffff window]
[    0.267664] pci_bus 0000:00: resource 5 [io  0x0000-0x0cf7 window]
[    0.267666] pci_bus 0000:00: resource 6 [io  0x1000-0x2fff window]
[    0.267668] pci_bus 0000:00: resource 7 [io  0x3000-0x6fff window]
[    0.267670] pci_bus 0000:00: resource 8 [io  0x7000-0xafff window]
[    0.267672] pci_bus 0000:00: resource 9 [io  0xb000-0xffff window]
[    0.267674] pci_bus 0000:00: resource 10 [mem 0x000a0000-0x000bffff window]
[    0.267676] pci_bus 0000:00: resource 11 [mem 0xe8000000-0xf3ffffff window]
[    0.267678] pci_bus 0000:01: resource 0 [io  0x1000-0x1fff]
[    0.267680] pci_bus 0000:01: resource 1 [mem 0xf2000000-0xf30fffff]
[    0.267682] pci_bus 0000:01: resource 2 [mem 0xe8000000-0xf1ffffff 64bit pref]
[    0.267685] pci_bus 0000:08: resource 1 [mem 0xf3300000-0xf33fffff]
[    0.267687] pci_bus 0000:28: resource 0 [io  0x3000-0x3fff]
[    0.267689] pci_bus 0000:28: resource 1 [mem 0xf8000000-0xf81fffff]
[    0.267691] pci_bus 0000:28: resource 2 [mem 0xf8200000-0xf83fffff 64bit pref]
[    0.267693] pci_bus 0000:34: resource 0 [io  0x4000-0x4fff]
[    0.267695] pci_bus 0000:34: resource 1 [mem 0xf8400000-0xf85fffff]
[    0.267697] pci_bus 0000:34: resource 2 [mem 0xf8600000-0xf87fffff 64bit pref]
[    0.267699] pci_bus 0000:3f: resource 0 [io  0x5000-0x5fff]
[    0.267701] pci_bus 0000:3f: resource 1 [mem 0xf3100000-0xf31fffff]
[    0.267703] pci_bus 0000:3f: resource 2 [mem 0xf8800000-0xf89fffff 64bit pref]
[    0.267705] pci_bus 0000:10: resource 4 [mem 0xf8000000-0xfebfffff window]
[    0.267707] pci_bus 0000:10: resource 5 [io  0x0000-0x0cf7 window]
[    0.267709] pci_bus 0000:10: resource 6 [io  0x1000-0x2fff window]
[    0.267711] pci_bus 0000:10: resource 7 [io  0x3000-0x6fff window]
[    0.267713] pci_bus 0000:10: resource 8 [io  0x7000-0xafff window]
[    0.267715] pci_bus 0000:10: resource 9 [io  0xb000-0xffff window]
[    0.267717] pci_bus 0000:10: resource 10 [mem 0x000a0000-0x000bffff window]
[    0.267719] pci_bus 0000:10: resource 11 [mem 0xe8000000-0xf3ffffff window]
[    0.267748] NET: Registered protocol family 2
[    0.267934] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
[    0.268149] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    0.268487] TCP: Hash tables configured (established 65536 bind 65536)
[    0.268530] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[    0.268577] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[    0.268654] NET: Registered protocol family 1
[    0.270061] pci 0000:01:00.0: Video device with shadowed ROM
[    0.270212] PCI: CLS 64 bytes, default 64
[    0.270259] Unpacking initramfs...
[    0.806227] Freeing initrd memory: 40160K
[    0.806269] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    0.806273] software IO TLB: mapped [mem 0xe2fc1000-0xe6fc1000] (64MB)
[    0.806463] Scanning for low memory corruption every 60 seconds
[    0.806840] audit: initializing netlink subsys (disabled)
[    0.806865] audit: type=2000 audit(1598593689.804:1): initialized
[    0.807185] Initialise system trusted keyring
[    0.807324] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.809104] zbud: loaded
[    0.809387] VFS: Disk quotas dquot_6.6.0
[    0.809425] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.809721] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.809982] fuse init (API version 7.23)
[    0.810122] Key type big_key registered
[    0.810137] Allocating IMA MOK and blacklist keyrings.
[    0.810534] Key type asymmetric registered
[    0.810538] Asymmetric key parser 'x509' registered
[    0.810576] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    0.810608] io scheduler noop registered
[    0.810611] io scheduler deadline registered (default)
[    0.810646] io scheduler cfq registered
[    0.811328] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.811337] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.811376] intel_idle: does not run on family 6 model 23
[    0.811458] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[    0.811462] ACPI: Power Button [PBTN]
[    0.811502] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[    0.811504] ACPI: Power Button [PWRF]
[    0.811561] tsc: Marking TSC unstable due to TSC halts in idle
[    0.811565] ACPI: acpi_idle registered with cpuidle
[    0.811768] GHES: HEST is not enabled!
[    0.811861] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[    0.832233] 00:04: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[    0.833845] Linux agpgart interface v0.103
[    0.835393] loop: module loaded
[    0.835607] libphy: Fixed MDIO Bus: probed
[    0.835610] tun: Universal TUN/TAP device driver, 1.6
[    0.835612] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.835649] PPP generic driver version 2.4.2
[    0.835707] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.835712] ehci-pci: EHCI PCI platform driver
[    0.835833] ehci-pci 0000:00:1a.7: EHCI Host Controller
[    0.835842] ehci-pci 0000:00:1a.7: new USB bus registered, assigned bus number 1
[    0.835853] ehci-pci 0000:00:1a.7: debug port 1
[    0.839743] ehci-pci 0000:00:1a.7: cache line size of 64 is not supported
[    0.839756] ehci-pci 0000:00:1a.7: irq 22, io mem 0xf3204800
[    0.852013] ehci-pci 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[    0.852053] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.852056] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.852058] usb usb1: Product: EHCI Host Controller
[    0.852060] usb usb1: Manufacturer: Linux 4.4.0-187-generic ehci_hcd
[    0.852062] usb usb1: SerialNumber: 0000:00:1a.7
[    0.852170] hub 1-0:1.0: USB hub found
[    0.852177] hub 1-0:1.0: 6 ports detected
[    0.852418] ehci-pci 0000:00:1d.7: EHCI Host Controller
[    0.852424] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 2
[    0.852433] ehci-pci 0000:00:1d.7: debug port 1
[    0.856344] ehci-pci 0000:00:1d.7: cache line size of 64 is not supported
[    0.856355] ehci-pci 0000:00:1d.7: irq 20, io mem 0xf3204c00
[    0.868025] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    0.868070] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    0.868073] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.868076] usb usb2: Product: EHCI Host Controller
[    0.868079] usb usb2: Manufacturer: Linux 4.4.0-187-generic ehci_hcd
[    0.868082] usb usb2: SerialNumber: 0000:00:1d.7
[    0.868227] hub 2-0:1.0: USB hub found
[    0.868233] hub 2-0:1.0: 6 ports detected
[    0.868376] ehci-platform: EHCI generic platform driver
[    0.868386] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.868391] ohci-pci: OHCI PCI platform driver
[    0.868403] ohci-platform: OHCI generic platform driver
[    0.868412] uhci_hcd: USB Universal Host Controller Interface driver
[    0.868509] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[    0.868515] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[    0.868521] uhci_hcd 0000:00:1a.0: detected 2 ports
[    0.868538] uhci_hcd 0000:00:1a.0: irq 20, io base 0x00002100
[    0.868576] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    0.868578] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.868580] usb usb3: Product: UHCI Host Controller
[    0.868582] usb usb3: Manufacturer: Linux 4.4.0-187-generic uhci_hcd
[    0.868584] usb usb3: SerialNumber: 0000:00:1a.0
[    0.868687] hub 3-0:1.0: USB hub found
[    0.868694] hub 3-0:1.0: 2 ports detected
[    0.868864] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[    0.868873] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[    0.868879] uhci_hcd 0000:00:1a.1: detected 2 ports
[    0.868900] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00002120
[    0.868938] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    0.868941] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.868943] usb usb4: Product: UHCI Host Controller
[    0.868945] usb usb4: Manufacturer: Linux 4.4.0-187-generic uhci_hcd
[    0.868947] usb usb4: SerialNumber: 0000:00:1a.1
[    0.869049] hub 4-0:1.0: USB hub found
[    0.869055] hub 4-0:1.0: 2 ports detected
[    0.869224] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[    0.869230] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
[    0.869236] uhci_hcd 0000:00:1a.2: detected 2 ports
[    0.869252] uhci_hcd 0000:00:1a.2: irq 22, io base 0x00002140
[    0.869291] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[    0.869293] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.869295] usb usb5: Product: UHCI Host Controller
[    0.869297] usb usb5: Manufacturer: Linux 4.4.0-187-generic uhci_hcd
[    0.869299] usb usb5: SerialNumber: 0000:00:1a.2
[    0.869408] hub 5-0:1.0: USB hub found
[    0.869414] hub 5-0:1.0: 2 ports detected
[    0.869587] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    0.869593] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
[    0.869599] uhci_hcd 0000:00:1d.0: detected 2 ports
[    0.869615] uhci_hcd 0000:00:1d.0: irq 20, io base 0x00002160
[    0.869653] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[    0.869655] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.869657] usb usb6: Product: UHCI Host Controller
[    0.869659] usb usb6: Manufacturer: Linux 4.4.0-187-generic uhci_hcd
[    0.869661] usb usb6: SerialNumber: 0000:00:1d.0
[    0.869760] hub 6-0:1.0: USB hub found
[    0.869766] hub 6-0:1.0: 2 ports detected
[    0.869933] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    0.869939] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
[    0.869944] uhci_hcd 0000:00:1d.1: detected 2 ports
[    0.869960] uhci_hcd 0000:00:1d.1: irq 21, io base 0x00002180
[    0.869998] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[    0.870001] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.870003] usb usb7: Product: UHCI Host Controller
[    0.870005] usb usb7: Manufacturer: Linux 4.4.0-187-generic uhci_hcd
[    0.870007] usb usb7: SerialNumber: 0000:00:1d.1
[    0.870107] hub 7-0:1.0: USB hub found
[    0.870113] hub 7-0:1.0: 2 ports detected
[    0.870286] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    0.870292] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
[    0.870298] uhci_hcd 0000:00:1d.2: detected 2 ports
[    0.870314] uhci_hcd 0000:00:1d.2: irq 22, io base 0x000021a0
[    0.870352] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
[    0.870355] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.870357] usb usb8: Product: UHCI Host Controller
[    0.870359] usb usb8: Manufacturer: Linux 4.4.0-187-generic uhci_hcd
[    0.870361] usb usb8: SerialNumber: 0000:00:1d.2
[    0.870456] hub 8-0:1.0: USB hub found
[    0.870462] hub 8-0:1.0: 2 ports detected
[    0.870601] xhci_hcd 0000:08:00.0: xHCI Host Controller
[    0.870607] xhci_hcd 0000:08:00.0: new USB bus registered, assigned bus number 9
[    0.870790] xhci_hcd 0000:08:00.0: hcc params 0x002841eb hci version 0x100 quirks 0x00000090
[    0.870862] usb usb9: New USB device found, idVendor=1d6b, idProduct=0002
[    0.870864] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.870866] usb usb9: Product: xHCI Host Controller
[    0.870868] usb usb9: Manufacturer: Linux 4.4.0-187-generic xhci-hcd
[    0.870870] usb usb9: SerialNumber: 0000:08:00.0
[    0.870971] hub 9-0:1.0: USB hub found
[    0.870979] hub 9-0:1.0: 1 port detected
[    0.871050] xhci_hcd 0000:08:00.0: xHCI Host Controller
[    0.871054] xhci_hcd 0000:08:00.0: new USB bus registered, assigned bus number 10
[    0.871073] usb usb10: We don't know the algorithms for LPM for this host, disabling LPM.
[    0.871091] usb usb10: New USB device found, idVendor=1d6b, idProduct=0003
[    0.871093] usb usb10: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.871095] usb usb10: Product: xHCI Host Controller
[    0.871097] usb usb10: Manufacturer: Linux 4.4.0-187-generic xhci-hcd
[    0.871099] usb usb10: SerialNumber: 0000:08:00.0
[    0.871198] hub 10-0:1.0: USB hub found
[    0.871207] hub 10-0:1.0: 4 ports detected
[    0.871362] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
[    0.874016] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.874021] serio: i8042 AUX port at 0x60,0x64 irq 12
[    0.874159] mousedev: PS/2 mouse device common for all mice
[    0.874305] rtc_cmos 00:00: RTC can wake from S4
[    0.874418] rtc_cmos 00:00: rtc core: registered rtc_cmos as rtc0
[    0.874439] rtc_cmos 00:00: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[    0.874447] i2c /dev entries driver
[    0.874495] device-mapper: uevent: version 1.0.3
[    0.874563] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[    0.874576] ledtrig-cpu: registered to indicate activity on CPUs
[    0.874916] NET: Registered protocol family 10
[    0.875113] NET: Registered protocol family 17
[    0.875123] Key type dns_resolver registered
[    0.875274] microcode: CPU0 sig=0x1067a, pf=0x1, revision=0xa0b
[    0.875278] microcode: CPU1 sig=0x1067a, pf=0x1, revision=0xa0b
[    0.875314] microcode: Microcode Update Driver: v2.01 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    0.875464] registered taskstats version 1
[    0.875479] Loading compiled-in X.509 certificates
[    0.876383] Loaded X.509 cert 'Build time autogenerated kernel key: f06b7227f29f55afa9b8968d1b82289d30ebc7c3'
[    0.876399] zswap: loaded using pool lzo/zbud
[    0.878486] Key type trusted registered
[    0.882032] Key type encrypted registered
[    0.882038] AppArmor: AppArmor sha1 policy hashing enabled
[    0.882041] ima: No TPM chip found, activating TPM-bypass!
[    0.882047] ima: Allocated hash algorithm: sha1
[    0.882068] evm: HMAC attrs: 0x1
[    0.882317]   Magic number: 0:433:821
[    0.882411] rtc_cmos 00:00: setting system clock to 2020-08-28 05:48:10 UTC (1598593690)
[    0.882489] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    0.882491] EDD information not available.
[    0.882536] PM: Hibernation image not present or could not be loaded.
[    0.883853] Freeing unused kernel memory: 1492K
[    0.896083] Write protecting the kernel read-only data: 14336k
[    0.896732] Freeing unused kernel memory: 1592K
[    0.896880] Freeing unused kernel memory: 56K
[    0.908326] random: systemd-udevd: uninitialized urandom read (16 bytes read, 2 bits of entropy available)
[    0.908421] random: systemd-udevd: uninitialized urandom read (16 bytes read, 2 bits of entropy available)
[    0.908437] random: systemd-udevd: uninitialized urandom read (16 bytes read, 2 bits of entropy available)
[    0.908455] random: systemd-udevd: uninitialized urandom read (16 bytes read, 2 bits of entropy available)
[    0.908866] random: udevadm: uninitialized urandom read (16 bytes read, 2 bits of entropy available)
[    0.908890] random: udevadm: uninitialized urandom read (16 bytes read, 2 bits of entropy available)
[    0.918803] random: systemd-udevd: uninitialized urandom read (16 bytes read, 3 bits of entropy available)
[    0.918824] random: systemd-udevd: uninitialized urandom read (16 bytes read, 3 bits of entropy available)
[    0.918834] random: systemd-udevd: uninitialized urandom read (16 bytes read, 3 bits of entropy available)
[    0.919091] random: systemd-udevd: uninitialized urandom read (16 bytes read, 3 bits of entropy available)
[    0.967476] FUJITSU Extended Socket Network Device Driver - version 1.0 - Copyright (c) 2015 FUJITSU LIMITED
[    0.986614] pps_core: LinuxPPS API ver. 1 registered
[    0.986616] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.987830] PTP clock support registered
[    0.990781] tg3.c:v3.137 (May 11, 2014)
[    0.993071] FDC 0 is a post-1991 82077
[    0.994781] ahci 0000:00:1f.2: version 3.0
[    0.994884] ahci 0000:00:1f.2: controller can't do SNTF, turning off CAP_SNTF
[    0.994962] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl RAID mode
[    0.994966] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part ccc sxs 
[    0.995830] scsi host0: ahci
[    0.995938] scsi host1: ahci
[    0.996036] scsi host2: ahci
[    0.996120] scsi host3: ahci
[    0.996202] scsi host4: ahci
[    0.996286] scsi host5: ahci
[    0.996337] ata1: SATA max UDMA/133 abar m2048@0xf3204000 port 0xf3204100 irq 30
[    0.996340] ata2: SATA max UDMA/133 abar m2048@0xf3204000 port 0xf3204180 irq 30
[    0.996342] ata3: SATA max UDMA/133 abar m2048@0xf3204000 port 0xf3204200 irq 30
[    0.996344] ata4: SATA max UDMA/133 abar m2048@0xf3204000 port 0xf3204280 irq 30
[    0.996346] ata5: SATA max UDMA/133 abar m2048@0xf3204000 port 0xf3204300 irq 30
[    0.996348] ata6: SATA max UDMA/133 abar m2048@0xf3204000 port 0xf3204380 irq 30
[    1.011245] tg3 0000:3f:00.0 eth0: Tigon3 [partno(BCM95755) rev a002] (PCI Express) MAC address 00:25:b3:d1:e4:ae
[    1.011249] tg3 0000:3f:00.0 eth0: attached PHY is 5755 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0])
[    1.011251] tg3 0000:3f:00.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[    1.011254] tg3 0000:3f:00.0 eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[    1.038369] tg3 0000:3f:00.0 enp63s0: renamed from eth0
[    1.080319] usb 10-1: new SuperSpeed USB device number 2 using xhci_hcd
[    1.180028] usb 2-1: new high-speed USB device number 2 using ehci-pci
[    1.313655] usb 2-1: New USB device found, idVendor=0bda, idProduct=8176
[    1.313659] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    1.313662] usb 2-1: Product: 802.11n WLAN Adapter
[    1.313665] usb 2-1: Manufacturer: Realtek
[    1.313668] usb 2-1: SerialNumber: 00e04c000001
[    1.316041] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.316060] ata6: SATA link down (SStatus 0 SControl 300)
[    1.320037] ata4: SATA link down (SStatus 0 SControl 300)
[    1.320054] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.320067] ata5: SATA link down (SStatus 0 SControl 300)
[    1.320083] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.321089] ata3.00: ATAPI: hp       DVDROM DH20N, DB02, max UDMA/100
[    1.321775] ata1.00: supports DRM functions and may not be fully accessible
[    1.322167] ata1.00: disabling queued TRIM support
[    1.322170] ata1.00: ATA-9: Samsung SSD 850 EVO 250GB, EMT02B6Q, max UDMA/133
[    1.322173] ata1.00: 488397168 sectors, multi 1: LBA48 NCQ (depth 31/32), AA
[    1.322465] ata3.00: configured for UDMA/100
[    1.322905] ata1.00: supports DRM functions and may not be fully accessible
[    1.323161] ata1.00: disabling queued TRIM support
[    1.323599] ata1.00: configured for UDMA/133
[    1.323757] scsi 0:0:0:0: Direct-Access     ATA      Samsung SSD 850  2B6Q PQ: 0 ANSI: 5
[    1.324099] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/233 GiB)
[    1.324118] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.324299] sd 0:0:0:0: [sda] Write Protect is off
[    1.324303] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.324330] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.324645]  sda: sda1
[    1.324914] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.335479] usb 10-1: New USB device found, idVendor=2109, idProduct=0812
[    1.335482] usb 10-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    1.335484] usb 10-1: Product: USB3.0 Hub             
[    1.335486] usb 10-1: Manufacturer: VIA Labs, Inc.         
[    1.335960] hub 10-1:1.0: USB hub found
[    1.336117] hub 10-1:1.0: 4 ports detected
[    1.355768] ata2.00: ATA-7: WDC WD3200JS-63PDB1, 21.00M22, max UDMA/133
[    1.355772] ata2.00: 625142448 sectors, multi 0: LBA48 
[    1.356489] ata2.00: configured for UDMA/133
[    1.356618] scsi 1:0:0:0: Direct-Access     ATA      WDC WD3200JS-63P 0M22 PQ: 0 ANSI: 5
[    1.356810] sd 1:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[    1.356851] sd 1:0:0:0: [sdb] Write Protect is off
[    1.356854] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    1.356873] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.357105] sd 1:0:0:0: Attached scsi generic sg1 type 0
[    1.357893] scsi 2:0:0:0: CD-ROM            hp       DVDROM DH20N     DB02 PQ: 0 ANSI: 5
[    1.373480] sr 2:0:0:0: [sr0] scsi3-mmc drive: 12x/40x cd/rw xa/form2 cdda tray
[    1.373484] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.373624] sr 2:0:0:0: Attached scsi CD-ROM sr0
[    1.373701] sr 2:0:0:0: Attached scsi generic sg2 type 5
[    1.392312]  sdb: sdb1 sdb2 < sdb5 sdb6 sdb7 >
[    1.392762] sd 1:0:0:0: [sdb] Attached SCSI disk
[    1.444028] usb 9-1: new high-speed USB device number 2 using xhci_hcd
[    1.552026] usb 6-2: new low-speed USB device number 2 using uhci_hcd
[    1.573423] usb 9-1: New USB device found, idVendor=2109, idProduct=3431
[    1.573427] usb 9-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    1.573430] usb 9-1: Product: USB2.0 Hub
[    1.573862] hub 9-1:1.0: USB hub found
[    1.574147] hub 9-1:1.0: 4 ports detected
[    1.720124] usb 6-2: New USB device found, idVendor=1bcf, idProduct=0005
[    1.720128] usb 6-2: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[    1.720131] usb 6-2: Product: USB Optical Mouse
[    1.728627] hidraw: raw HID events driver (C) Jiri Kosina
[    1.746393] usbcore: registered new interface driver usbhid
[    1.746395] usbhid: USB HID core driver
[    1.748135] input: USB Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb6/6-2/6-2:1.0/0003:1BCF:0005.0001/input/input5
[    1.748228] hid-generic 0003:1BCF:0005.0001: input,hidraw0: USB HID v1.10 Mouse [USB Optical Mouse] on usb-0000:00:1d.0-2/input0
[    1.804035] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2b3eebcc770, max_idle_ns: 440795277129 ns
[    1.852024] usb 9-1.1: new high-speed USB device number 3 using xhci_hcd
[    1.941475] usb 9-1.1: New USB device found, idVendor=2109, idProduct=2812
[    1.941480] usb 9-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    1.941483] usb 9-1.1: Product: USB2.0 Hub             
[    1.941486] usb 9-1.1: Manufacturer: VIA Labs, Inc.         
[    1.941979] hub 9-1.1:1.0: USB hub found
[    1.942116] hub 9-1.1:1.0: 4 ports detected
[    2.276023] usb 7-2: new low-speed USB device number 2 using uhci_hcd
[    2.456045] usb 7-2: New USB device found, idVendor=049f, idProduct=0051
[    2.456050] usb 7-2: New USB device strings: Mfr=1, Product=8, SerialNumber=0
[    2.456053] usb 7-2: Product: Compaq USB Keyboard
[    2.456056] usb 7-2: Manufacturer: CHICONY
[    2.474498] input: CHICONY Compaq USB Keyboard as /devices/pci0000:00/0000:00:1d.1/usb7/7-2/7-2:1.0/0003:049F:0051.0002/input/input6
[    2.528152] hid-generic 0003:049F:0051.0002: input,hidraw1: USB HID v1.10 Keyboard [CHICONY Compaq USB Keyboard] on usb-0000:00:1d.1-2/input0
[    2.558104] input: CHICONY Compaq USB Keyboard as /devices/pci0000:00/0000:00:1d.1/usb7/7-2/7-2:1.1/0003:049F:0051.0003/input/input7
[    2.612197] hid-generic 0003:049F:0051.0003: input,hiddev0,hidraw2: USB HID v1.10 Device [CHICONY Compaq USB Keyboard] on usb-0000:00:1d.1-2/input1
[    4.154181] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[    4.258121] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN)
[    4.258249] systemd[1]: Detected architecture x86-64.
[    4.258398] systemd[1]: Set hostname to <christophe-2>.
[    4.318602] random: nonblocking pool is initialized
[    4.337751] systemd[1]: [/etc/systemd/system/snap-opera-87.mount:10] Unknown lvalue 'LazyUnmount' in section 'Mount'
[    4.338014] systemd[1]: [/etc/systemd/system/snap-vlc-1620.mount:10] Unknown lvalue 'LazyUnmount' in section 'Mount'
[    4.339758] systemd[1]: [/etc/systemd/system/snap-kde\x2dframeworks\x2d5\x2dcore18-32.mount:10] Unknown lvalue 'LazyUnmount' in section 'Mount'
[    4.340819] systemd[1]: [/etc/systemd/system/snap-gtk\x2dcommon\x2dthemes-1506.mount:10] Unknown lvalue 'LazyUnmount' in section 'Mount'
[    4.341320] systemd[1]: [/etc/systemd/system/snap-core-9665.mount:10] Unknown lvalue 'LazyUnmount' in section 'Mount'
[    4.341625] systemd[1]: [/etc/systemd/system/snap-core18-1885.mount:10] Unknown lvalue 'LazyUnmount' in section 'Mount'
[    4.341920] systemd[1]: [/etc/systemd/system/snap-gtk2\x2dcommon\x2dthemes-13.mount:10] Unknown lvalue 'LazyUnmount' in section 'Mount'
[    4.342436] systemd[1]: [/etc/systemd/system/snap-gimp-292.mount:10] Unknown lvalue 'LazyUnmount' in section 'Mount'
[    4.342814] systemd[1]: [/etc/systemd/system/snap-gtk2\x2dcommon\x2dthemes-9.mount:10] Unknown lvalue 'LazyUnmount' in section 'Mount'
[    4.343161] systemd[1]: [/etc/systemd/system/snap-core-9804.mount:10] Unknown lvalue 'LazyUnmount' in section 'Mount'
[    4.343517] systemd[1]: [/etc/systemd/system/snap-core18-1880.mount:10] Unknown lvalue 'LazyUnmount' in section 'Mount'
[    4.343792] systemd[1]: [/etc/systemd/system/snap-vlc-1700.mount:10] Unknown lvalue 'LazyUnmount' in section 'Mount'
[    4.344312] systemd[1]: [/etc/systemd/system/snap-chromium\x2dffmpeg-15.mount:10] Unknown lvalue 'LazyUnmount' in section 'Mount'
[    4.344617] systemd[1]: [/etc/systemd/system/snap-opera-86.mount:10] Unknown lvalue 'LazyUnmount' in section 'Mount'
[    4.344992] systemd[1]: [/etc/systemd/system/snap-gnome\x2d3\x2d28\x2d1804-128.mount:10] Unknown lvalue 'LazyUnmount' in section 'Mount'
[    4.345610] systemd[1]: [/etc/systemd/system/snap-chromium-1269.mount:10] Unknown lvalue 'LazyUnmount' in section 'Mount'
[    4.346167] systemd[1]: [/etc/systemd/system/snap-gnome\x2d3\x2d28\x2d1804-116.mount:10] Unknown lvalue 'LazyUnmount' in section 'Mount'
[    4.346608] systemd[1]: [/etc/systemd/system/snap-chromium-1260.mount:10] Unknown lvalue 'LazyUnmount' in section 'Mount'
[    4.346894] systemd[1]: [/etc/systemd/system/snap-gtk\x2dcommon\x2dthemes-1502.mount:10] Unknown lvalue 'LazyUnmount' in section 'Mount'
[    4.347162] systemd[1]: [/etc/systemd/system/snap-gimp-281.mount:10] Unknown lvalue 'LazyUnmount' in section 'Mount'
[    4.352415] systemd[1]: Listening on udev Kernel Socket.
[    4.352494] systemd[1]: Listening on fsck to fsckd communication Socket.
[    4.352594] systemd[1]: Created slice User and Session Slice.
[    4.352642] systemd[1]: Started Trigger resolvconf update for networkd DNS.
[    4.352688] systemd[1]: Listening on Journal Socket (/dev/log).
[    4.352844] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    4.352892] systemd[1]: Listening on udev Control Socket.
[    4.352963] systemd[1]: Listening on Journal Audit Socket.
[    4.352990] systemd[1]: Reached target Encrypted Volumes.
[    4.353023] systemd[1]: Listening on Syslog Socket.
[    4.353043] systemd[1]: Reached target User and Group Name Lookups.
[    4.353118] systemd[1]: Created slice System Slice.
[    4.353207] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[    4.353263] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    4.353280] systemd[1]: Reached target Slices.
[    4.353329] systemd[1]: Listening on Journal Socket.
[    4.364181] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[    4.364754] systemd[1]: Starting Uncomplicated firewall...
[    4.365647] systemd[1]: Starting Set console keymap...
[    4.367518] systemd[1]: Starting Load Kernel Modules...
[    4.368139] systemd[1]: Starting Journal Service...
[    4.368696] systemd[1]: Mounting Debug File System...
[    4.369298] systemd[1]: Mounting Huge Pages File System...
[    4.370393] systemd[1]: Starting Remount Root and Kernel File Systems...
[    4.370487] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[    4.370527] systemd[1]: Reached target Remote File Systems (Pre).
[    4.370548] systemd[1]: Reached target Remote File Systems.
[    4.371196] systemd[1]: Mounting POSIX Message Queue File System...
[    4.378946] systemd[1]: Started Create list of required static device nodes for the current kernel.
[    4.379743] systemd[1]: Started Uncomplicated firewall.
[    4.380217] systemd[1]: Mounted Debug File System.
[    4.380401] systemd[1]: Mounted Huge Pages File System.
[    4.380614] systemd[1]: Mounted POSIX Message Queue File System.
[    4.381997] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[    4.382640] systemd[1]: Starting Create Static Device Nodes in /dev...
[    4.384269] systemd[1]: Started Remount Root and Kernel File Systems.
[    4.388728] systemd[1]: Starting udev Coldplug all Devices...
[    4.391449] lp: driver loaded but no devices found
[    4.405020] ppdev: user-space parallel port driver
[    4.407095] parport_pc 00:03: reported by Plug and Play ACPI
[    4.407166] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[    4.408596] systemd[1]: Started Create Static Device Nodes in /dev.
[    4.409308] systemd[1]: Starting udev Kernel Device Manager...
[    4.472764] systemd[1]: Started Journal Service.
[    4.504153] lp0: using parport0 (interrupt-driven).
[    4.513653] smsc47b397: found SMSC SCH5317 (base address 0x0480, revision 1)
[    4.579645] EDAC MC: Ver: 3.0.0
[    4.582049] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    4.582722] wmi: Mapper loaded
[    4.601972] EDAC MC0: Giving out device to module x38_edac controller x38: DEV 0000:00:00.0 (POLLED)
[    4.611766] [drm] Initialized drm 1.1.0 20060810
[    4.707327] nvidia: loading out-of-tree module taints kernel.
[    4.707335] nvidia: module license 'NVIDIA' taints kernel.
[    4.707336] Disabling lock debugging due to kernel taint
[    4.729553] nvidia: module verification failed: signature and/or required key missing - tainting kernel
[    4.758280] snd_hda_intel 0000:01:00.1: Disabling MSI
[    4.758289] snd_hda_intel 0000:01:00.1: Handle vga_switcheroo audio client
[    4.775877] snd_hda_codec_realtek hdaudioC0D0: ALC262: SKU not ready 0x411111f0
[    4.776497] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC262: line_outs=1 (0x15/0x0/0x0/0x0/0x0) type:line
[    4.776501] snd_hda_codec_realtek hdaudioC0D0:    speaker_outs=1 (0x16/0x0/0x0/0x0/0x0)
[    4.776503] snd_hda_codec_realtek hdaudioC0D0:    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[    4.776505] snd_hda_codec_realtek hdaudioC0D0:    mono: mono_out=0x0
[    4.776507] snd_hda_codec_realtek hdaudioC0D0:    inputs:
[    4.776509] snd_hda_codec_realtek hdaudioC0D0:      Rear Mic=0x18
[    4.776512] snd_hda_codec_realtek hdaudioC0D0:      Front Mic=0x19
[    4.776514] snd_hda_codec_realtek hdaudioC0D0:      Line=0x1a
[    4.776516] snd_hda_codec_realtek hdaudioC0D0:      CD=0x1c
[    4.776518] snd_hda_codec_realtek hdaudioC0D0:      Aux=0x14
[    4.789600] input: HDA Intel Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[    4.789669] input: HDA Intel Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[    4.789730] input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[    4.789793] input: HDA Intel Line Out as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[    4.789854] input: HDA Intel Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[    4.790414] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[    4.790648] [drm] Initialized nvidia-drm 0.0.0 20150116 for 0000:01:00.0 on minor 0
[    4.790656] NVRM: loading NVIDIA UNIX x86_64 Kernel Module  340.107  Thu May 24 21:54:01 PDT 2018
[    4.803988] kvm: disabled by bios
[    4.829078] kvm: disabled by bios
[    4.830642] intel_powerclamp: No package C-state available
[    4.860431] intel_powerclamp: No package C-state available
[    4.929000] gpio_ich: GPIO from 451 to 511 on gpio_ich
[    4.950799] input: HP WMI hotkeys as /devices/virtual/input/input13
[    4.990982] nvidia_uvm: Loaded the UVM driver, major device number 245
[    5.196521] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input14
[    5.196591] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input15
[    5.747032] rtl8192cu: Chip version 0x10
[    5.768522] cfg80211: World regulatory domain updated:
[    5.768524] cfg80211:  DFS Master region: unset
[    5.768524] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[    5.768526] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[    5.768528] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[    5.768529] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[    5.768531] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[    5.768532] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[    5.768534] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[    5.768535] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[    5.768536] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[    5.840398] rtl8192cu: MAC address: 20:f4:1b:4f:19:cd
[    5.840400] rtl8192cu: Board Type 0
[    5.840645] rtl_usb: rx_max_size 15360, rx_urb_num 8, in_ep 1
[    5.840667] rtl8192cu: Loading firmware rtlwifi/rtl8192cufw_TMSC.bin
[    5.849041] ieee80211 phy0: Selected rate control algorithm 'rtl_rc'
[    5.849929] usbcore: registered new interface driver rtl8192cu
[    5.853295] usbcore: registered new interface driver rtl8xxxu
[    5.855727] rtl8192cu 2-1:1.0 wlx20f41b4f19cd: renamed from wlan0
[    6.318520] Adding 3143676k swap on /dev/sdb5.  Priority:-1 extents:1 across:3143676k FS
[    6.566347] EXT4-fs (sdb7): mounted filesystem with ordered data mode. Opts: (null)
[    6.618873] EXT4-fs (sdb6): mounted filesystem with ordered data mode. Opts: (null)
[    6.708201] systemd-journald[289]: Received request to flush runtime journal from PID 1
[    7.431949] audit: type=1400 audit(1598593697.044:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/sbin/dhclient" pid=868 comm="apparmor_parser"
[    7.431959] audit: type=1400 audit(1598593697.044:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=868 comm="apparmor_parser"
[    7.431965] audit: type=1400 audit(1598593697.044:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=868 comm="apparmor_parser"
[    7.431970] audit: type=1400 audit(1598593697.044:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=868 comm="apparmor_parser"
[    7.432514] audit: type=1400 audit(1598593697.048:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/lightdm/lightdm-guest-session" pid=867 comm="apparmor_parser"
[    7.432521] audit: type=1400 audit(1598593697.048:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/lightdm/lightdm-guest-session//chromium" pid=867 comm="apparmor_parser"
[    7.445783] audit: type=1400 audit(1598593697.060:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/evince" pid=870 comm="apparmor_parser"
[    7.445792] audit: type=1400 audit(1598593697.060:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/evince//sanitized_helper" pid=870 comm="apparmor_parser"
[    7.445797] audit: type=1400 audit(1598593697.060:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/evince-previewer" pid=870 comm="apparmor_parser"
[    7.445803] audit: type=1400 audit(1598593697.060:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/evince-previewer//sanitized_helper" pid=870 comm="apparmor_parser"
[   11.322793] IPv6: ADDRCONF(NETDEV_UP): wlx20f41b4f19cd: link is not ready
[   11.324521] rtl8192cu: MAC auto ON okay!
[   11.376655] rtl8192cu: Tx queue select: 0x05
[   11.784318] IPv6: ADDRCONF(NETDEV_UP): wlx20f41b4f19cd: link is not ready
[   11.791359] IPv6: ADDRCONF(NETDEV_UP): enp63s0: link is not ready
[   11.829960] IPv6: ADDRCONF(NETDEV_UP): enp63s0: link is not ready
[   11.941334] IPv6: ADDRCONF(NETDEV_UP): wlx20f41b4f19cd: link is not ready
[   36.860444] wlx20f41b4f19cd: authenticate with 42:21:d0:97:0d:e0
[   36.883453] wlx20f41b4f19cd: send auth to 42:21:d0:97:0d:e0 (try 1/3)
[   36.894039] wlx20f41b4f19cd: authenticated
[   36.894169] rtl8192cu 2-1:1.0 wlx20f41b4f19cd: disabling HT/VHT due to WEP/TKIP use
[   36.896106] wlx20f41b4f19cd: associate with 42:21:d0:97:0d:e0 (try 1/3)
[   36.913917] wlx20f41b4f19cd: RX AssocResp from 42:21:d0:97:0d:e0 (capab=0x411 status=0 aid=3)
[   37.019175] wlx20f41b4f19cd: associated
[   37.019191] IPv6: ADDRCONF(NETDEV_CHANGE): wlx20f41b4f19cd: link becomes ready
[ 1387.384049] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
[ 1470.894358] perf interrupt took too long (2502 > 2500), lowering kernel.perf_event_max_sample_rate to 50000
[23030.310711] audit_printk_skb: 132 callbacks suppressed
[23030.310715] audit: type=1400 audit(1598616719.923:56): apparmor="DENIED" operation="open" profile="/usr/bin/evince" name="/var/lib/snapd/desktop/applications/mimeinfo.cache" pid=8644 comm="evince" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[23030.310791] audit: type=1400 audit(1598616719.923:57): apparmor="DENIED" operation="open" profile="/usr/bin/evince" name="/var/lib/snapd/desktop/applications/mimeinfo.cache" pid=8644 comm="evince" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[23055.201366] audit: type=1400 audit(1598616744.815:58): apparmor="DENIED" operation="open" profile="/usr/bin/evince" name="/var/lib/snapd/desktop/applications/mimeinfo.cache" pid=8681 comm="evince" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[23055.201460] audit: type=1400 audit(1598616744.815:59): apparmor="DENIED" operation="open" profile="/usr/bin/evince" name="/var/lib/snapd/desktop/applications/mimeinfo.cache" pid=8681 comm="evince" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[34866.521684] audit: type=1400 audit(1598628556.133:60): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/snap/core/9804/usr/lib/snapd/snap-confine" pid=9645 comm="apparmor_parser"
[34866.536036] audit: type=1400 audit(1598628556.149:61): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/snap/core/9804/usr/lib/snapd/snap-confine//mount-namespace-capture-helper" pid=9645 comm="apparmor_parser"
[34867.032987] audit: type=1400 audit(1598628556.645:62): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="snap-update-ns.chromium" pid=9647 comm="apparmor_parser"
[34868.495032] audit: type=1400 audit(1598628558.105:63): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="snap.chromium.chromedriver" pid=9648 comm="apparmor_parser"
[34869.937904] audit: type=1400 audit(1598628559.549:64): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="snap.chromium.chromium" pid=9650 comm="apparmor_parser"
[34869.942283] audit: type=1400 audit(1598628559.553:65): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="snap-update-ns.core" pid=9652 comm="apparmor_parser"
[34869.944178] audit: type=1400 audit(1598628559.557:66): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="snap.core.hook.configure" pid=9653 comm="apparmor_parser"
[36869.940268] usb 10-4: new SuperSpeed USB device number 3 using xhci_hcd
[36869.956919] usb 10-4: New USB device found, idVendor=1058, idProduct=25a1
[36869.956923] usb 10-4: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[36869.956926] usb 10-4: Product: Elements 25A1
[36869.956929] usb 10-4: Manufacturer: Western Digital
[36869.956933] usb 10-4: SerialNumber: 5758313244333044464B3830
[36869.981048] usb-storage 10-4:1.0: USB Mass Storage device detected
[36869.982653] scsi host6: usb-storage 10-4:1.0
[36869.982902] usbcore: registered new interface driver usb-storage
[36869.989898] usbcore: registered new interface driver uas
[36870.980427] scsi 6:0:0:0: Direct-Access     WD       Elements 25A1    1018 PQ: 0 ANSI: 6
[36870.980916] sd 6:0:0:0: Attached scsi generic sg3 type 0
[36870.984961] sd 6:0:0:0: [sdc] Spinning up disk...
[36871.988035] ......ready
[36877.008289] sd 6:0:0:0: [sdc] Very big device. Trying to use READ CAPACITY(16).
[36877.008408] sd 6:0:0:0: [sdc] 5860466688 512-byte logical blocks: (3.00 TB/2.73 TiB)
[36877.008410] sd 6:0:0:0: [sdc] 4096-byte physical blocks
[36877.008763] sd 6:0:0:0: [sdc] Write Protect is off
[36877.008766] sd 6:0:0:0: [sdc] Mode Sense: 47 00 10 08
[36877.009123] sd 6:0:0:0: [sdc] No Caching mode page found
[36877.009126] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[36877.010940] sd 6:0:0:0: [sdc] Very big device. Trying to use READ CAPACITY(16).
[36877.190486]  sdc: sdc1
[36877.192813] sd 6:0:0:0: [sdc] Very big device. Trying to use READ CAPACITY(16).
[36877.193737] sd 6:0:0:0: [sdc] Attached SCSI disk
[36948.768493] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36948.904465] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36949.040584] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36949.176485] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36949.316495] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36949.456529] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36949.476773] sd 6:0:0:0: [sdc] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[36949.476780] sd 6:0:0:0: [sdc] tag#0 CDB: Read(16) 88 00 00 00 00 00 39 e9 f3 20 00 00 00 f0 00 00
[36949.476783] blk_update_request: I/O error, dev sdc, sector 971633440
[36949.620489] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36949.842636] audit: type=1400 audit(1598630639.454:67): apparmor="DENIED" operation="open" profile="/usr/bin/evince-thumbnailer" name="/home/christophe/.local/share/fonts/" pid=10072 comm="evince-thumbnai" requested_mask="r" denied_mask="r" fsuid=1000 ouid=1000
[36949.842676] audit: type=1400 audit(1598630639.454:68): apparmor="DENIED" operation="open" profile="/usr/bin/evince-thumbnailer" name="/home/christophe/.local/share/fonts/" pid=10072 comm="evince-thumbnai" requested_mask="r" denied_mask="r" fsuid=1000 ouid=1000
[36949.869121] audit: type=1400 audit(1598630639.486:69): apparmor="DENIED" operation="open" profile="/usr/bin/evince-thumbnailer" name="/home/christophe/.local/share/fonts/" pid=10072 comm="evince-thumbnai" requested_mask="r" denied_mask="r" fsuid=1000 ouid=1000
[36949.869167] audit: type=1400 audit(1598630639.486:70): apparmor="DENIED" operation="open" profile="/usr/bin/evince-thumbnailer" name="/home/christophe/.local/share/fonts/" pid=10072 comm="evince-thumbnai" requested_mask="r" denied_mask="r" fsuid=1000 ouid=1000
[36949.869184] audit: type=1400 audit(1598630639.486:71): apparmor="DENIED" operation="open" profile="/usr/bin/evince-thumbnailer" name="/home/christophe/.local/share/fonts/" pid=10072 comm="evince-thumbnai" requested_mask="r" denied_mask="r" fsuid=1000 ouid=1000
[36950.108512] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36950.252484] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36950.392487] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36950.532487] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36950.676476] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36950.816502] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36950.836773] sd 6:0:0:0: [sdc] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[36950.836780] sd 6:0:0:0: [sdc] tag#0 CDB: Read(16) 88 00 00 00 00 00 39 e8 71 c8 00 00 00 58 00 00
[36950.836783] blk_update_request: I/O error, dev sdc, sector 971534792
[36950.976525] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36951.116507] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36951.252513] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36951.388538] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36951.524495] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36951.660473] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36951.676928] sd 6:0:0:0: [sdc] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[36951.676935] sd 6:0:0:0: [sdc] tag#0 CDB: Read(16) 88 00 00 00 00 00 39 e5 a2 00 00 00 00 80 00 00
[36951.676939] blk_update_request: I/O error, dev sdc, sector 971350528
[36953.461448] audit: type=1400 audit(1598630643.074:72): apparmor="DENIED" operation="open" profile="/usr/bin/evince-thumbnailer" name="/home/christophe/.local/share/fonts/" pid=10104 comm="evince-thumbnai" requested_mask="r" denied_mask="r" fsuid=1000 ouid=1000
[36953.461487] audit: type=1400 audit(1598630643.074:73): apparmor="DENIED" operation="open" profile="/usr/bin/evince-thumbnailer" name="/home/christophe/.local/share/fonts/" pid=10104 comm="evince-thumbnai" requested_mask="r" denied_mask="r" fsuid=1000 ouid=1000
[36953.461528] audit: type=1400 audit(1598630643.074:74): apparmor="DENIED" operation="open" profile="/usr/bin/evince-thumbnailer" name="/home/christophe/.local/share/fonts/" pid=10104 comm="evince-thumbnai" requested_mask="r" denied_mask="r" fsuid=1000 ouid=1000
[36953.461551] audit: type=1400 audit(1598630643.074:75): apparmor="DENIED" operation="open" profile="/usr/bin/evince-thumbnailer" name="/home/christophe/.local/share/fonts/" pid=10104 comm="evince-thumbnai" requested_mask="r" denied_mask="r" fsuid=1000 ouid=1000
[36953.461562] audit: type=1400 audit(1598630643.074:76): apparmor="DENIED" operation="open" profile="/usr/bin/evince-thumbnailer" name="/home/christophe/.local/share/fonts/" pid=10104 comm="evince-thumbnai" requested_mask="r" denied_mask="r" fsuid=1000 ouid=1000
[36990.372542] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36990.508492] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36990.644508] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36990.780490] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36990.920491] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36991.060578] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36991.080837] sd 6:0:0:0: [sdc] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[36991.080843] sd 6:0:0:0: [sdc] tag#0 CDB: Read(16) 88 00 00 00 00 00 30 27 3c 20 00 00 00 f0 00 00
[36991.080846] blk_update_request: I/O error, dev sdc, sector 807877664
[37030.544509] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[37030.684495] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[37030.820475] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[37030.956477] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[37031.092481] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[37031.228488] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[37031.244773] sd 6:0:0:0: [sdc] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[37031.244781] sd 6:0:0:0: [sdc] tag#0 CDB: Read(16) 88 00 00 00 00 00 30 27 95 18 00 00 00 f0 00 00
[37031.244785] blk_update_request: I/O error, dev sdc, sector 807900440

christophe@christophe-2:~$ dmesg | tail -50
[36950.108512] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36950.252484] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36950.392487] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36950.532487] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36950.676476] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36950.816502] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36950.836773] sd 6:0:0:0: [sdc] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[36950.836780] sd 6:0:0:0: [sdc] tag#0 CDB: Read(16) 88 00 00 00 00 00 39 e8 71 c8 00 00 00 58 00 00
[36950.836783] blk_update_request: I/O error, dev sdc, sector 971534792
[36950.976525] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36951.116507] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36951.252513] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36951.388538] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36951.524495] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36951.660473] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36951.676928] sd 6:0:0:0: [sdc] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[36951.676935] sd 6:0:0:0: [sdc] tag#0 CDB: Read(16) 88 00 00 00 00 00 39 e5 a2 00 00 00 00 80 00 00
[36951.676939] blk_update_request: I/O error, dev sdc, sector 971350528
[36953.461448] audit: type=1400 audit(1598630643.074:72): apparmor="DENIED" operation="open" profile="/usr/bin/evince-thumbnailer" name="/home/christophe/.local/share/fonts/" pid=10104 comm="evince-thumbnai" requested_mask="r" denied_mask="r" fsuid=1000 ouid=1000
[36953.461487] audit: type=1400 audit(1598630643.074:73): apparmor="DENIED" operation="open" profile="/usr/bin/evince-thumbnailer" name="/home/christophe/.local/share/fonts/" pid=10104 comm="evince-thumbnai" requested_mask="r" denied_mask="r" fsuid=1000 ouid=1000
[36953.461528] audit: type=1400 audit(1598630643.074:74): apparmor="DENIED" operation="open" profile="/usr/bin/evince-thumbnailer" name="/home/christophe/.local/share/fonts/" pid=10104 comm="evince-thumbnai" requested_mask="r" denied_mask="r" fsuid=1000 ouid=1000
[36953.461551] audit: type=1400 audit(1598630643.074:75): apparmor="DENIED" operation="open" profile="/usr/bin/evince-thumbnailer" name="/home/christophe/.local/share/fonts/" pid=10104 comm="evince-thumbnai" requested_mask="r" denied_mask="r" fsuid=1000 ouid=1000
[36953.461562] audit: type=1400 audit(1598630643.074:76): apparmor="DENIED" operation="open" profile="/usr/bin/evince-thumbnailer" name="/home/christophe/.local/share/fonts/" pid=10104 comm="evince-thumbnai" requested_mask="r" denied_mask="r" fsuid=1000 ouid=1000
[36990.372542] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36990.508492] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36990.644508] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36990.780490] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36990.920491] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36991.060578] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[36991.080837] sd 6:0:0:0: [sdc] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[36991.080843] sd 6:0:0:0: [sdc] tag#0 CDB: Read(16) 88 00 00 00 00 00 30 27 3c 20 00 00 00 f0 00 00
[36991.080846] blk_update_request: I/O error, dev sdc, sector 807877664
[37030.544509] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[37030.684495] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[37030.820475] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[37030.956477] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[37031.092481] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[37031.228488] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[37031.244773] sd 6:0:0:0: [sdc] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[37031.244781] sd 6:0:0:0: [sdc] tag#0 CDB: Read(16) 88 00 00 00 00 00 30 27 95 18 00 00 00 f0 00 00
[37031.244785] blk_update_request: I/O error, dev sdc, sector 807900440
[37044.128543] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[37044.264495] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[37044.401324] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[37044.536493] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[37044.672492] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[37044.812474] usb 10-4: reset SuperSpeed USB device number 3 using xhci_hcd
[37044.828773] sd 6:0:0:0: [sdc] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[37044.828781] sd 6:0:0:0: [sdc] tag#0 CDB: Read(16) 88 00 00 00 00 00 30 27 b3 18 00 00 00 f0 00 00
[37044.828784] blk_update_request: I/O error, dev sdc, sector 807908120
christophe@christophe-2:~$

Il y a encore des "I/O error" mais bon le disque marche nickel pourtant

geole · Le 28/08/2020, à 17:11

Où est-passé ce disque?
après l'avoir rebranché.

dmesg | tail -50

ou/et

lsblk -e7

devraient te permettre de trouver son nom.

hunt · Le 28/08/2020, à 17:13

Ce serait étonnant que le disque soit endommagé, je l'ai sorti de la boite hier, et j'en ai pris soin, je ne l'ai pas démonté à l'arrache, j'ai bien fait "éjecter" / retirer le volume sans risque........
Je l'ai pas testé sous ma machine windows encore.....
C'est régulier quand même les problémes de montage sous Ubuntu, ça fait des années et des années, ils ne se sont pas améliorés dessus...

hunt · Le 28/08/2020, à 17:14

Sur quelle machine ?
La première ? mais il était en sdf ! j'ai vérifié quand j'ai vu qu'il n'était pas notifié, j'ai refait les commandes justement pour voir où il était noté comme présent : sdf

Dernière modification par hunt (Le 28/08/2020, à 17:15)

geole · Le 28/08/2020, à 17:18

"Il y a encore des "I/O error" mais bon le disque marche nickel pourtant"

en version 16.04
merci de donner le retour de

lsblk -e7

journalctl   |  grep   "I/O error"

je t ai déjà demandé le nom du logiciel de sauvegarde utilisé en version 16.04

tu pourras aussi y faire le smartctl

Est-ce le même ordinateur qui possède ubuntu 16.04 et ubuntu 18.04

Dernière modification par geole (Le 28/08/2020, à 17:28)

hunt · Le 28/08/2020, à 17:24

Bon sous la 18.04, je retente :

christophe@christophe-System-Product-Name:~$ dmesg | tail -50
[35555.118444] sd 9:0:0:0: [sdf] 4096-byte physical blocks
[35555.118468] sd 9:0:0:0: [sdf] Attached SCSI disk
[36618.804602] usb 10-3: new SuperSpeed USB device number 5 using xhci_hcd
[36618.834018] usb 10-3: New USB device found, idVendor=1058, idProduct=25a1
[36618.834021] usb 10-3: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[36618.834023] usb 10-3: Product: Elements 25A1
[36618.834025] usb 10-3: Manufacturer: Western Digital
[36618.834026] usb 10-3: SerialNumber: 5758313244333044464B3830
[36618.835864] usb-storage 10-3:1.0: USB Mass Storage device detected
[36618.837854] scsi host9: usb-storage 10-3:1.0
[36619.860637] scsi 9:0:0:0: Direct-Access     WD       Elements 25A1    1018 PQ: 0 ANSI: 6
[36619.860980] sd 9:0:0:0: Attached scsi generic sg6 type 0
[36619.864212] sd 9:0:0:0: [sdf] Spinning up disk...
[36620.883790] .
[36621.939766] .
[36622.963746] .
[36623.987736] .
[36625.011710] .
[36626.067686] .
[36627.091672] .
[36628.115656] .
[36629.139639] .
[36630.195609] .
[36631.219591] .
[36632.243562] .
[36633.267546] .
[36634.291529] .
[36635.315505] .
[36636.339483] .
[36637.363459] .
[36638.419447] .
[36639.443418] .
[36640.467401] .
[36641.491376] .
[36642.515359] .
[36643.539337] .
[36644.563318] .
[36645.587300] .
[36646.643283] .
[36647.667258] .
[36648.691235] .
[36649.715217] .
[36650.739191] .
[36651.763172] .
[36652.787157] .
[36653.811137] .
[36654.867112] .
[36655.891088] .
[36656.915067] .
[36657.939047] .
christophe@christophe-System-Product-Name:~$

christophe@christophe-System-Product-Name:~$ lsblk -e7
NAME   MAJ:MIN RM   SIZE RO TYPE MOUNTPOINT
sda      8:0    0 931,5G  0 disk 
└─sda1   8:1    0 931,5G  0 part /
sdf      8:80   0   2,7T  0 disk 
sr0     11:0    1  1024M  0 rom  
christophe@christophe-System-Product-Name:~$

et donc :

christophe@christophe-System-Product-Name:~$ sudo smartctl   -s on   -a /dev/sdf[sudo] Mot de passe de christophe : 
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.15.0-112-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

/dev/sdf: Unknown USB bridge [0x1058:0x25a1 (0x1018)]
Please specify device type with the -d option.

Use smartctl -h to get a usage summary

christophe@christophe-System-Product-Name:~$

truc de fou......
Je vais repasser sous 16.04...

hunt · Le 28/08/2020, à 17:25

Aucun logiciel de sauvegarde, c'est via Nautilus, copié coller

hunt · Le 28/08/2020, à 17:30

Sous la 16.04 :

christophe@christophe-2:~$ lsblk -e7
NAME   MAJ:MIN RM   SIZE RO TYPE MOUNTPOINT
sda      8:0    0 232,9G  0 disk 
└─sda1   8:1    0 232,9G  0 part /
sdb      8:16   0 298,1G  0 disk 
├─sdb1   8:17   0  48,8G  0 part /media/christophe/308ed996-7f74-42cc-95db-79789
├─sdb2   8:18   0     1K  0 part 
├─sdb5   8:21   0     3G  0 part [SWAP]
├─sdb6   8:22   0  55,9G  0 part /var
└─sdb7   8:23   0 190,4G  0 part /home
sdc      8:32   0   2,7T  0 disk 
└─sdc1   8:33   0   2,7T  0 part /media/christophe/Elements
sr0     11:0    1  1024M  0 rom  
christophe@christophe-2:~$ journalctl   |  grep   "I/O error"
août 28 18:03:59 christophe-2 kernel: blk_update_request: I/O error, dev sdc, sector 971633440
août 28 18:04:00 christophe-2 kernel: blk_update_request: I/O error, dev sdc, sector 971534792
août 28 18:04:01 christophe-2 kernel: blk_update_request: I/O error, dev sdc, sector 971350528
août 28 18:04:40 christophe-2 kernel: blk_update_request: I/O error, dev sdc, sector 807877664
août 28 18:05:20 christophe-2 kernel: blk_update_request: I/O error, dev sdc, sector 807900440
août 28 18:05:34 christophe-2 kernel: blk_update_request: I/O error, dev sdc, sector 807908120
août 28 18:10:17 christophe-2 kernel: blk_update_request: I/O error, dev sdc, sector 6160976
août 28 18:18:43 christophe-2 kernel: blk_update_request: I/O error, dev sdc, sector 6228176
août 28 18:18:44 christophe-2 kernel: blk_update_request: I/O error, dev sdc, sector 6228185
août 28 18:18:44 christophe-2 kernel: Buffer I/O error on dev sdc1, logical block 6226137, async page read
août 28 18:18:44 christophe-2 kernel: Buffer I/O error on dev sdc1, logical block 6226138, async page read
août 28 18:18:44 christophe-2 kernel: Buffer I/O error on dev sdc1, logical block 6226139, async page read
août 28 18:18:44 christophe-2 kernel: Buffer I/O error on dev sdc1, logical block 6226140, async page read
août 28 18:18:44 christophe-2 kernel: Buffer I/O error on dev sdc1, logical block 6226141, async page read
août 28 18:18:44 christophe-2 kernel: Buffer I/O error on dev sdc1, logical block 6226142, async page read
août 28 18:18:44 christophe-2 kernel: Buffer I/O error on dev sdc1, logical block 6226143, async page read
août 28 18:18:44 christophe-2 kernel: Buffer I/O error on dev sdc1, logical block 6226137, async page read
août 28 18:18:44 christophe-2 kernel: Buffer I/O error on dev sdc1, logical block 6226138, async page read
août 28 18:18:44 christophe-2 kernel: Buffer I/O error on dev sdc1, logical block 6226139, async page read
août 28 18:27:23 christophe-2 kernel: blk_update_request: I/O error, dev sdc, sector 6233808
août 28 18:27:24 christophe-2 kernel: blk_update_request: I/O error, dev sdc, sector 6234064
août 28 18:27:24 christophe-2 kernel: blk_update_request: I/O error, dev sdc, sector 6233825
août 28 18:27:24 christophe-2 kernel: Buffer I/O error on dev sdc1, logical block 6231777, async page read
août 28 18:27:24 christophe-2 kernel: Buffer I/O error on dev sdc1, logical block 6231778, async page read
août 28 18:27:24 christophe-2 kernel: Buffer I/O error on dev sdc1, logical block 6231779, async page read
août 28 18:27:24 christophe-2 kernel: Buffer I/O error on dev sdc1, logical block 6231780, async page read
août 28 18:27:24 christophe-2 kernel: Buffer I/O error on dev sdc1, logical block 6231781, async page read
août 28 18:27:24 christophe-2 kernel: Buffer I/O error on dev sdc1, logical block 6231782, async page read
août 28 18:27:24 christophe-2 kernel: Buffer I/O error on dev sdc1, logical block 6231783, async page read
août 28 18:27:25 christophe-2 kernel: Buffer I/O error on dev sdc1, logical block 6231777, async page read
août 28 18:27:25 christophe-2 kernel: Buffer I/O error on dev sdc1, logical block 6231778, async page read
août 28 18:27:25 christophe-2 kernel: Buffer I/O error on dev sdc1, logical block 6231779, async page read
août 28 18:28:28 christophe-2 kernel: blk_update_request: I/O error, dev sdc, sector 6236112
christophe@christophe-2:~$

geole · Le 28/08/2020, à 17:37

Avec ce retour du code erreur ( Unknown USB bridge [0x1058:0x25a1 (0x1018)] ), essaie

       sudo smartctl   -s on -d sat  -a /dev/sdf

Un peu d'humour.

https://www.debian-fr.org/t/ports-usb3-qui-repondent-mal/63102/3 a écrit :

Pour l’instant, quand je branche un disque dur sur le port USB3, je vais faire le café, la vaisselle, les vitres, etc., et il finit par ce monter tout seul… : Et ensuite je peux l’utiliser de manière assez fiable. [edit 2 : j’ai chronométré, ça prend un tout petit peu moins de 20 minutes…]

Dernière modification par geole (Le 28/08/2020, à 17:53)

hunt · Le 28/08/2020, à 18:56

Oui autant en rire effectivement
Bon ça fait plus de 15 ans maintenant que je pratique Ubuntu, j'ai eu le temps de m'y faire
Mais bon ça reste dommage, et empêche franchement le développement de Linux et du libre......

Bon j'ai retenté les commandes sur la 18.04 :

christophe@christophe-System-Product-Name:~$ lsblk -e7
NAME   MAJ:MIN RM   SIZE RO TYPE MOUNTPOINT
sda      8:0    0 931,5G  0 disk 
└─sda1   8:1    0 931,5G  0 part /
sdf      8:80   0   2,7T  0 disk 
sr0     11:0    1  1024M  0 rom  
christophe@christophe-System-Product-Name:~$ sudo smartctl   -s on   -a /dev/sdf[sudo] Mot de passe de christophe : 
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.15.0-112-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

/dev/sdf: Unknown USB bridge [0x1058:0x25a1 (0x1018)]
Please specify device type with the -d option.

Use smartctl -h to get a usage summary

La commande sudo smartctl -s on -d sat -a /dev/sdf ne donne rien du tout... ça mouline mais rien ne sort depuis tout à l'heure

hunt · Le 28/08/2020, à 19:00

Je ne comprends pas que le disque soit à la fois recensé comme présent, puis derrière unknown...

hunt · Le 28/08/2020, à 19:00

quand le disque externe est branché, impossible même de lancer gparted... ça mouline non stop mais rien

geole · Le 28/08/2020, à 19:15

Cela enquête longuement. Dans l'extrait, il disait que même les autres usb étaient bloqués... jusqu'à la fin de l'enquête.

Le tout va être de savoir les rôles Logiciel ubuntu, Module UAS, matériel de liaison dont ports USB et qualité du disque.
Cela sent malgré tout le bug.

J'ai noté qu'en version 16.04, La partition est trouvée donc au besoin, fais le smartctl et j'ai cru comprendre que c'était le même ordinateur

Dernière modification par geole (Le 28/08/2020, à 19:16)

hunt · Le 28/08/2020, à 19:26

bon j'ai pas trop le temps de le laisser tourner là...
C'est bizarre quand même un bug de ce type, d'autant que ce n'est pas la première fois que j'ai le même genre de souci.... j'ai un autre disque SSD, pareil ! impossible de le monter sur les mêmes machines (ce sont tous des ordis séparés)...
En revanche, dans mes souvenirs j'avais réussi à brancher un disque dur HDD, qui était très bien reconnu..... est ce que cela viendrait du type de technologie ? les 2 SSD, ce sont les mêmes Western Digital.....

Ubuntu-fr

Navigation

Liens de recherche

Annonce

#1 Le 28/08/2020, à 13:02

Probléme montage disque dur externe

#2 Le 28/08/2020, à 13:26

Re : Probléme montage disque dur externe

#3 Le 28/08/2020, à 13:49

Re : Probléme montage disque dur externe

#4 Le 28/08/2020, à 13:58

Re : Probléme montage disque dur externe

#5 Le 28/08/2020, à 14:03

Re : Probléme montage disque dur externe

#6 Le 28/08/2020, à 14:06

Re : Probléme montage disque dur externe

#7 Le 28/08/2020, à 14:06

Re : Probléme montage disque dur externe

#8 Le 28/08/2020, à 14:14

Re : Probléme montage disque dur externe

#9 Le 28/08/2020, à 15:29

Re : Probléme montage disque dur externe

#10 Le 28/08/2020, à 16:08

Re : Probléme montage disque dur externe

#11 Le 28/08/2020, à 17:01

Re : Probléme montage disque dur externe

#12 Le 28/08/2020, à 17:08

Re : Probléme montage disque dur externe

#13 Le 28/08/2020, à 17:11

Re : Probléme montage disque dur externe

#14 Le 28/08/2020, à 17:13

Re : Probléme montage disque dur externe

#15 Le 28/08/2020, à 17:14

Re : Probléme montage disque dur externe

#16 Le 28/08/2020, à 17:18

Re : Probléme montage disque dur externe

#17 Le 28/08/2020, à 17:24

Re : Probléme montage disque dur externe

#18 Le 28/08/2020, à 17:25

Re : Probléme montage disque dur externe

#19 Le 28/08/2020, à 17:30

Re : Probléme montage disque dur externe

#20 Le 28/08/2020, à 17:37

Re : Probléme montage disque dur externe

#21 Le 28/08/2020, à 18:56

Re : Probléme montage disque dur externe

#22 Le 28/08/2020, à 19:00

Re : Probléme montage disque dur externe

#23 Le 28/08/2020, à 19:00

Re : Probléme montage disque dur externe

#24 Le 28/08/2020, à 19:15

Re : Probléme montage disque dur externe

#25 Le 28/08/2020, à 19:26

Re : Probléme montage disque dur externe

Pied de page des forums