Pages : 1
#1 Le 23/03/2022, à 07:48
- iznobe
Etat des disques durs
Bonjour , hier j' ai recupere 2 disques durs , un seagate de 4 TO et un autre de 1 TO .
voici les rapports smart pour le disque de 4 TO :
iznobe@iznobe-PC:~$ sudo smartctl -s on -a /dev/sde
smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.13.0-35-generic] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Surveillance
Device Model: ST4000VX000-2AG166
Serial Number: WDH0N1LY
LU WWN Device Id: 5 000c50 09d04af26
Firmware Version: CV11
User Capacity: 4000787030016 bytes [4,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5980 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-3 T13/2161-D revision 5
SATA Version is: SATA 3.1, 6.0 Gb/s
Local Time is: Wed Mar 23 07:39:55 2022 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 591) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 651) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x50bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 080 064 044 Pre-fail Always - 89211272
3 Spin_Up_Time 0x0003 094 093 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 868
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 095 060 045 Pre-fail Always - 3229549622
9 Power_On_Hours 0x0032 055 055 000 Old_age Always - 39585 (135 212 0)
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 687
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 087 087 000 Old_age Always - 13
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 069 044 040 Old_age Always - 31 (Min/Max 18/31)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 306
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 1067
194 Temperature_Celsius 0x0022 031 056 000 Old_age Always - 31 (0 17 0 0 0)
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 33096 (31 195 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 743592922688
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 16451473908
SMART Error Log Version: 1
ATA Error Count: 13 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 13 occurred at disk power-on lifetime: 39188 hours (1632 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 10 ff ff ff ef 00 4d+16:18:14.430 READ DMA EXT
35 00 10 ff ff ff ef 00 4d+16:18:14.425 WRITE DMA EXT
25 00 10 ff ff ff ef 00 4d+16:18:14.410 READ DMA EXT
35 00 00 ff ff ff ef 00 4d+16:18:14.400 WRITE DMA EXT
35 00 00 ff ff ff ef 00 4d+16:18:14.360 WRITE DMA EXT
Error 12 occurred at disk power-on lifetime: 31441 hours (1310 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 1d+15:25:50.487 READ DMA EXT
27 00 00 00 00 00 e0 00 1d+15:25:50.486 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 1d+15:25:50.485 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 1d+15:25:50.485 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 1d+15:25:50.454 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 11 occurred at disk power-on lifetime: 31441 hours (1310 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 1d+15:25:47.691 READ DMA EXT
27 00 00 00 00 00 e0 00 1d+15:25:47.690 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 1d+15:25:47.689 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 1d+15:25:47.689 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 1d+15:25:47.633 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 10 occurred at disk power-on lifetime: 31441 hours (1310 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 1d+15:25:44.850 READ DMA EXT
27 00 00 00 00 00 e0 00 1d+15:25:44.849 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 1d+15:25:44.848 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 1d+15:25:44.848 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 1d+15:25:44.836 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 9 occurred at disk power-on lifetime: 31441 hours (1310 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 ff ff ff ef 00 1d+15:25:42.072 READ DMA EXT
27 00 00 00 00 00 e0 00 1d+15:25:42.071 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 1d+15:25:42.070 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 1d+15:25:42.070 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 1d+15:25:42.013 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
iznobe@iznobe-PC:~$ et pour le 1 TO :
iznobe@iznobe-PC:~$ sudo smartctl -s on -a /dev/sdd
smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.13.0-35-generic] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.14 (AF)
Device Model: ST1000DM003-1SB10C
Serial Number: Z9A031KY
LU WWN Device Id: 5 000c50 086f4f19d
Firmware Version: CC41
User Capacity: 1000204886016 bytes [1,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-3 T13/2161-D revision 3b
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Wed Mar 23 07:47:28 2022 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 105) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x10a5) SCT Status supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 071 063 006 Pre-fail Always - 13026079
3 Spin_Up_Time 0x0003 097 096 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 750
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 079 060 045 Pre-fail Always - 89101967
9 Power_On_Hours 0x0032 066 066 000 Old_age Always - 30108
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 734
183 Runtime_Bad_Block 0x0032 099 099 000 Old_age Always - 1
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 093 000 Old_age Always - 18 18 20
189 High_Fly_Writes 0x003a 099 099 000 Old_age Always - 1
190 Airflow_Temperature_Cel 0x0022 069 048 040 Old_age Always - 31 (Min/Max 18/31)
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 1404
194 Temperature_Celsius 0x0022 031 010 000 Old_age Always - 31 (0 10 0 0 0)
195 Hardware_ECC_Recovered 0x001a 019 001 000 Old_age Always - 13026079
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 198 000 Old_age Always - 522
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 19368h+18m+53.622s
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 38712908482
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 14522387759
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
iznobe@iznobe-PC:~$j ' ajouterais que ce disque fait parfois des bruits bizzares et anormaux au demarrage , comme si le moteur ou les tetes , ne fonctionnait pas correctement .
Qu ' en pensez vous ?
Dernière modification par iznobe (Le 23/03/2022, à 07:49)
retour COMPLET et utilisable de commande
MSI Z490A-pro , i7 10700 , 32 GB RAM .
Hors ligne
#2 Le 23/03/2022, à 10:40
- FrancisFDZ
Re : Etat des disques durs
Bonjour,
Je vois :
Disque 4To
Error 13 occurred at disk power-on lifetime: 39188 hours (1632 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.Error 11 occurred at disk power-on lifetime: 31441 hours (1310 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.Error 10 occurred at disk power-on lifetime: 31441 hours (1310 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.Error 9 occurred at disk power-on lifetime: 31441 hours (1310 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.(par ordre d'apparition)
Disque 1To
SMART Error Log Version: 1
No Errors LoggedJ'en pense que le disque de 1To semble sain, l'autre serait à surveiller, l'avis d'un spécialiste de SmartDisk est bien sur nécessaire.
A priori, ça me semble encore utilisable. (si poubelle, donnes moi l'adresse de ta poubelle 
)
Dernière modification par FrancisFDZ (Le 24/03/2022, à 08:58)
-- On peut avoir des raisons de se plaindre et n'avoir pas raison de se plaindre --
[Victor Hugo]
Hors ligne
Pages : 1