#1 Le 28/10/2023, à 09:08
- cyval
interprétation résultat smartctl disque dur seagate
bonjour,
je viens de faire l'acquisition d'un disque dur Seagate IronWolf 1 To.
celui-ci est raccordé à mon raspberry depuis hier matin.
lorsque je réalise le ctrl du DD ce matin via smartctl, j'obtiens le résultat suivi :
pi@raspberrypi:~ $ sudo smartctl --all /dev/sdb
smartctl 6.6 2017-11-05 r4594 [armv7l-linux-5.15.49-v7l+] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate IronWolf
Device Model: ST1000VN002-2EY102
Serial Number: Z9CE6HMG
LU WWN Device Id: 5 000c50 0e3f7683d
Firmware Version: SC60
User Capacity: 1000204886016 bytes [1,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5900 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Sat Oct 28 08:53:27 2023 BST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 592) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 124) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x10bf) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 074 074 006 Pre-fail Always - 26140781
3 Spin_Up_Time 0x0003 099 099 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 20
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 100 253 045 Pre-fail Always - 9477
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 15
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 20
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 072 072 040 Old_age Always - 28 (Min/Max 22/28)
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 21
194 Temperature_Celsius 0x0022 028 022 000 Old_age Always - 28 (0 22 0 0 0)
195 Hardware_ECC_Recovered 0x001a 015 015 000 Old_age Always - 26140781
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.l'attribut "Read Error Rate" m'inquiète fortement.
qu'en pensez-vous ? le disque dur est défaillant ?
merci d'avance pour votre aide
Hors ligne
#2 Le 28/10/2023, à 10:32
- jpoc
Re : interprétation résultat smartctl disque dur seagate
Hors ligne
#3 Le 28/10/2023, à 11:24
- geole
Re : interprétation résultat smartctl disque dur seagate
autreBonjour.
L'attribut que tu sites n'est pas catastrophique.
Il est possible qu'il soit la conséquence de cette situation que je trouve anormale.
195 Hardware_ECC_Recovered 0x001a 015 015 000 Old_age Always - 26140781Un message plus alarmant
Et un autre semblant prouver que cela n'est pas obligatoirement dans le disque lui-même.
Regarde si le cable SATA est bien enfiché. tu peux aussi tenter de le remplacer.
Dernière modification par geole (Le 28/10/2023, à 12:22)
Les grilles de l'installateur https://doc.ubuntu-fr.org/tutoriel/inst … _subiquity
"gedit admin:///etc/fstab" est proscrit, utilisez "pkexec env DISPLAY=$DISPLAY XAUTHORITY=$XAUTHORITY xdg-open /etc/fstab" Voir https://doc.ubuntu-fr.org/gedit
Les partitions EXT4 des disques externes => https://forum.ubuntu-fr.org/viewtopic.p … #p22697248
En ligne