Ubuntu-fr

sarkan

Lecteur carte sd non reconnu

Bonjour à tous je me permets de poster un nouveau sujet sur ce problème de lecteur de carte sd non reconnu.
J'ai suivi de nombreux sur ce sujet(recompilation de noyau,....)mais rien ni fait lorsque j'insere ma carte sd la petite del clignote 2 ou 3 fois et puis c'est ubuntu ne m'indique rien.Mon ordinateur est un hp dv5 donc lecteur de carte intégré.
Je pose le lspci si ca peut faire avancer le chmilblique.
Merci d'avance

06:00.2 SD Host controller: JMicron Technology Corp. Standard SD Host Controller

maman

Re : Lecteur carte sd non reconnu

salut,
je me permets d'ajouter quelques infos. Ce fil fait suite à celui ci ./viewtopic.php?pid=3747856#p3747856
Après compilation du pilote JMicron, la carte ne vaut pas se monter.

Après avoir inséré ta carte, peux tu poster le retour de

sudo fdisk-l

dmesg

---

90% of teens today would die if Facebook was completely destroyed. If you are one of the 10% that would be laughing, copy and paste this to your signature.

sarkan

Re : Lecteur carte sd non reconnu

je viens de trouver l'utilitaire de disque et ma carte sd apparait et quand j'essaye de la monter j'ai ce message d'erreur
Error mounting: mount exited with exit code 1: helper failed with:
mount: according to mtab, none is already mounted on none
mount failed
Je ne sais pas si ca peut vous aider

Pour la commande sudo fdisk -l il me dit que c'est une commande inconnue.
pour dmesg

[    0.483567] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.483573] serio: i8042 AUX port at 0x60,0x64 irq 12
[    0.483684] mice: PS/2 mouse device common for all mice
[    0.485188] rtc_cmos 00:04: RTC can wake from S4
[    0.485221] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[    0.485247] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs
[    0.485342] device-mapper: uevent: version 1.0.3
[    0.485430] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[    0.485490] device-mapper: multipath: version 1.1.0 loaded
[    0.485493] device-mapper: multipath round-robin: version 1.0.0 loaded
[    0.485594] EISA: Probing bus 0 at eisa.0
[    0.485602] Cannot allocate resource for EISA slot 2
[    0.485604] Cannot allocate resource for EISA slot 3
[    0.485606] Cannot allocate resource for EISA slot 4
[    0.485608] Cannot allocate resource for EISA slot 5
[    0.485610] Cannot allocate resource for EISA slot 6
[    0.485612] Cannot allocate resource for EISA slot 7
[    0.485613] Cannot allocate resource for EISA slot 8
[    0.485615] EISA: Detected 0 cards.
[    0.485748] cpuidle: using governor ladder
[    0.485862] cpuidle: using governor menu
[    0.486299] TCP cubic registered
[    0.486450] NET: Registered protocol family 10
[    0.486919] lo: Disabled Privacy Extensions
[    0.487260] NET: Registered protocol family 17
[    0.487712] Using IPI No-Shortcut mode
[    0.487782] PM: Resume from disk failed.
[    0.487794] registered taskstats version 1
[    0.488593]   Magic number: 10:904:43
[    0.488654] rtc_cmos 00:04: setting system clock to 2010-09-24 20:02:47 UTC (1285358567)
[    0.488657] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    0.488659] EDD information not available.
[    0.504821] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
[    0.514440] ACPI: Battery Slot [BAT0] (battery present)
[    0.772027] usb 2-4: new high speed USB device using ehci_hcd and address 2
[    0.774164] isapnp: No Plug & Play device found
[    0.774190] Freeing unused kernel memory: 660k freed
[    0.774513] Write protecting the kernel text: 4680k
[    0.774564] Write protecting the kernel read-only data: 1844k
[    0.790491] udev: starting version 151
[    0.916636] ahci 0000:00:1f.2: version 3.0
[    0.916655] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    0.916698]   alloc irq_desc for 31 on node -1
[    0.916700]   alloc kstat_irqs on node -1
[    0.916710] ahci 0000:00:1f.2: irq 31 for MSI/MSI-X
[    0.916727] ahci 0000:00:1f.2: BIOS update required for suspend/resume
[    0.916792] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 4 ports 3 Gbps 0x33 impl SATA mode
[    0.916796] ahci 0000:00:1f.2: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part ccc ems sxs 
[    0.916801] ahci 0000:00:1f.2: setting latency timer to 64
[    0.926778] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    0.926799] r8169 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    0.926837] r8169 0000:03:00.0: setting latency timer to 64
[    0.926886]   alloc irq_desc for 32 on node -1
[    0.926888]   alloc kstat_irqs on node -1
[    0.926901] r8169 0000:03:00.0: irq 32 for MSI/MSI-X
[    0.927567] eth0: RTL8168c/8111c at 0xf80ce000, 00:1e:68:f9:9b:3e, XID 1c4000c0 IRQ 32
[    0.932929] usb 2-4: configuration #1 chosen from 1 choice
[    0.934808] ohci1394 0000:06:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.934817] ohci1394 0000:06:00.0: setting latency timer to 64
[    0.940152] scsi0 : ahci
[    0.940253] scsi1 : ahci
[    0.940314] scsi2 : ahci
[    0.940372] scsi3 : ahci
[    0.940430] scsi4 : ahci
[    0.940494] scsi5 : ahci
[    0.940685] ata1: SATA max UDMA/133 abar m2048@0xdf305000 port 0xdf305100 irq 31
[    0.940689] ata2: SATA max UDMA/133 abar m2048@0xdf305000 port 0xdf305180 irq 31
[    0.940691] ata3: DUMMY
[    0.940692] ata4: DUMMY
[    0.940695] ata5: SATA max UDMA/133 abar m2048@0xdf305000 port 0xdf305300 irq 31
[    0.940698] ata6: SATA max UDMA/133 abar m2048@0xdf305000 port 0xdf305380 irq 31
[    0.993100] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16]  MMIO=[da100000-da1007ff]  Max Packet=[2048]  IR/IT contexts=[4/4]
[    1.260046] ata5: SATA link down (SStatus 0 SControl 300)
[    1.260065] ata6: SATA link down (SStatus 0 SControl 300)
[    1.424041] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.424058] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.425692] ata1.00: ATA-8: WDC WD3200BEVT-60ZCT0, 12.01A12, max UDMA/100
[    1.425696] ata1.00: 625142448 sectors, multi 16: LBA48 
[    1.427499] ata1.00: configured for UDMA/100
[    1.427718] ata2.00: ATAPI: HL-DT-ST DVDRAM GSA-T30L, GC04, max UDMA/100
[    1.432450] ata2.00: configured for UDMA/100
[    1.440207] scsi 0:0:0:0: Direct-Access     ATA      WDC WD3200BEVT-6 12.0 PQ: 0 ANSI: 5
[    1.440354] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.440437] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[    1.440483] sd 0:0:0:0: [sda] Write Protect is off
[    1.440486] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.440513] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.440647]  sda: sda1 sda2 sda3 sda4
[    1.491701] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.555046] scsi 1:0:0:0: CD-ROM            HL-DT-ST DVDRAM GSA-T30L  GC04 PQ: 0 ANSI: 5
[    1.881451] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[    1.881454] Uniform CD-ROM driver Revision: 3.20
[    1.881556] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    1.881603] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    2.268149] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00241b00c1f73a01]
[    7.157872] EXT4-fs (sda3): mounted filesystem with ordered data mode
[   18.987443] udev: starting version 151
[   19.057111] lp: driver loaded but no devices found
[   19.142421] sdhci: Secure Digital Host Controller Interface driver
[   19.142424] sdhci: Copyright(c) Pierre Ossman
[   19.143772] sdhci-pci 0000:06:00.1: SDHCI controller found [197b:2382] (rev 0)
[   19.143796] sdhci-pci 0000:06:00.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   19.143839] sdhci-pci 0000:06:00.1: setting latency timer to 64
[   19.143876] Registered led device: mmc0::
[   19.143913] mmc0: SDHCI controller on PCI [0000:06:00.1] using DMA
[   19.143933] sdhci-pci 0000:06:00.2: SDHCI controller found [197b:2381] (rev 0)
[   19.143950] sdhci-pci 0000:06:00.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   19.143957] sdhci-pci 0000:06:00.2: Refusing to bind to secondary interface.
[   19.143964] sdhci-pci 0000:06:00.2: PCI INT A disabled
[   19.155472] Linux agpgart interface v0.103
[   19.157630] acpi device:07: registered as cooling_device2
[   19.157775] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:05/LNXVIDEO:01/input/input6
[   19.157825] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[   19.238396] vga16fb: initializing
[   19.238400] vga16fb: mapped to 0xc00a0000
[   19.238449] fb0: VGA16 VGA frame buffer device
[   19.244676] cfg80211: Calling CRDA to update world regulatory domain
[   19.287686] nvidia: module license 'NVIDIA' taints kernel.
[   19.287691] Disabling lock debugging due to kernel taint
[   19.351261] mmc0: new SD card at address 0002
[   20.110360] cfg80211: World regulatory domain updated:
[   20.110364]     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   20.110367]     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   20.110370]     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   20.110372]     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   20.110375]     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   20.110377]     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   20.121917] lis3lv02d: hardware type HPDV5_I found.
[   20.129356] Linux video capture interface: v2.00
[   20.132638] uvcvideo: Found UVC 1.00 device HP Webcam (064e:c107)
[   20.136187] lis3lv02d: 1-byte sensor found
[   20.151510] lirc_dev: IR Remote Control driver registered, major 61 
[   20.152165] lirc_dev: lirc_register_driver: sample_rate: 0
[   20.152257] enecir: KB3926C detected, driver support is not complete!
[   20.152260] enecir: chip is 0x3926 - 0x00, 0xc0
[   20.152266] enecir: hardware features:
[   20.152268] enecir: learning and tx off, gpio40_learn off, fan_in off
[   20.152270] enecir: driver has been succesfully loaded
[   20.167727] input: HP Webcam as /devices/pci0000:00/0000:00:1d.7/usb2/2-4/2-4:1.0/input/input7
[   20.167780] usbcore: registered new interface driver uvcvideo
[   20.167783] USB Video Class driver (v0.1.0)
[   20.177111] jmb38x_ms 0000:06:00.3: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   20.177118] jmb38x_ms 0000:06:00.3: setting latency timer to 64
[   20.181934] type=1505 audit(1285351387.191:2):  operation="profile_load" pid=702 name="/sbin/dhclient3"
[   20.182615] type=1505 audit(1285351387.191:3):  operation="profile_load" pid=702 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[   20.182979] type=1505 audit(1285351387.191:4):  operation="profile_load" pid=702 name="/usr/lib/connman/scripts/dhclient-script"
[   20.221679] mmcblk0: mmc0:0002 SD    3.68 GiB 
[   20.221737]  mmcblk0: p1
[   20.380102] nvidia 0000:01:00.0: power state changed by ACPI to D0
[   20.380116] nvidia 0000:01:00.0: power state changed by ACPI to D0
[   20.380135] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   20.380147] nvidia 0000:01:00.0: setting latency timer to 64
[   20.380154] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[   20.380823] NVRM: loading NVIDIA UNIX x86 Kernel Module  195.36.24  Thu Apr 22 09:18:20 PDT 2010
[   20.394747] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27k
[   20.394749] iwlagn: Copyright(c) 2003-2009 Intel Corporation
[   20.394918] iwlagn 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   20.394981] iwlagn 0000:02:00.0: setting latency timer to 64
[   20.395117] iwlagn 0000:02:00.0: Detected Intel Wireless WiFi Link 5100AGN REV=0x54
[   20.456945] iwlagn 0000:02:00.0: Tunable channels: 13 802.11bg, 24 802.11a channels
[   20.457198]   alloc irq_desc for 33 on node -1
[   20.457200]   alloc kstat_irqs on node -1
[   20.457259] iwlagn 0000:02:00.0: irq 33 for MSI/MSI-X
[   20.509386] phy0: Selected rate control algorithm 'iwl-agn-rs'
[   20.591319]   alloc irq_desc for 22 on node -1
[   20.591322]   alloc kstat_irqs on node -1
[   20.591329] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[   20.591364] HDA Intel 0000:00:1b.0: setting latency timer to 64
[   20.594607] Console: switching to colour frame buffer device 80x30
[   20.597295] input: ST LIS3LV02DL Accelerometer as /devices/platform/lis3lv02d/input/input8
[   20.597392] Registered led device: hp::hddprotect
[   20.597407] lis3lv02d driver loaded.
[   20.703915] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input9
[   20.721566] input: HDA Intel Mic at Ext Front Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[   20.721813] input: HDA Intel Mic at Sep UNKNOWN Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[   20.722001] input: HDA Intel HP Out at Ext Front Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[   21.429588] Synaptics Touchpad, model: 1, fw: 6.5, id: 0x1c0b1, caps: 0xa04751/0xa00000
[   21.510777] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input13
[   21.674117] type=1505 audit(1285351388.683:5):  operation="profile_load" pid=939 name="/usr/share/gdm/guest-session/Xsession"
[   21.675730] type=1505 audit(1285351388.683:6):  operation="profile_replace" pid=940 name="/sbin/dhclient3"
[   21.676512] type=1505 audit(1285351388.687:7):  operation="profile_replace" pid=940 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[   21.676988] type=1505 audit(1285351388.687:8):  operation="profile_replace" pid=940 name="/usr/lib/connman/scripts/dhclient-script"
[   21.684094] type=1505 audit(1285351388.695:9):  operation="profile_load" pid=941 name="/usr/bin/evince"
[   21.692906] type=1505 audit(1285351388.703:10):  operation="profile_load" pid=941 name="/usr/bin/evince-previewer"
[   21.696185] iwlagn 0000:02:00.0: firmware: requesting iwlwifi-5000-2.ucode
[   21.699669] type=1505 audit(1285351388.707:11):  operation="profile_load" pid=941 name="/usr/bin/evince-thumbnailer"
[   21.723764] iwlagn 0000:02:00.0: loaded firmware version 8.24.2.12
[   21.873250] Registered led device: iwl-phy0::radio
[   21.873481] Registered led device: iwl-phy0::assoc
[   21.873536] Registered led device: iwl-phy0::RX
[   21.873925] Registered led device: iwl-phy0::TX
[   21.885034] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   21.886585] r8169: eth0: link down
[   21.886789] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   22.166408] ppdev: user-space parallel port driver
[   22.385998] CPU0 attaching NULL sched-domain.
[   22.386003] CPU1 attaching NULL sched-domain.
[   23.679903] CPU0 attaching sched-domain:
[   23.679906]  domain 0: span 0-1 level MC
[   23.679908]   groups: 0 1
[   23.679912] CPU1 attaching sched-domain:
[   23.679914]  domain 0: span 0-1 level MC
[   23.679916]   groups: 1 0
[   28.822706] CPU0 attaching NULL sched-domain.
[   28.822711] CPU1 attaching NULL sched-domain.
[   28.844079] CPU0 attaching sched-domain:
[   28.844083]  domain 0: span 0-1 level MC
[   28.844086]   groups: 0 1
[   28.844091] CPU1 attaching sched-domain:
[   28.844093]  domain 0: span 0-1 level MC
[   28.844096]   groups: 1 0
[   38.271746] wlan0: deauthenticating from b2:1c:fd:25:c0:0c by local choice (reason=3)
[   38.271841] wlan0: direct probe to AP b2:1c:fd:25:c0:0c (try 1)
[   38.277378] wlan0: direct probe responded
[   38.277383] wlan0: authenticate with AP b2:1c:fd:25:c0:0c (try 1)
[   38.282777] wlan0: authenticated
[   38.282794] wlan0: associate with AP b2:1c:fd:25:c0:0c (try 1)
[   38.301224] wlan0: RX AssocResp from b2:1c:fd:25:c0:0c (capab=0x411 status=0 aid=2)
[   38.301228] wlan0: associated
[   38.302777] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   44.542569] wlan0: deauthenticated from b2:1c:fd:25:c0:0c (Reason: 15)
[   47.935426] wlan0: direct probe to AP b2:1c:fd:25:c0:0c (try 1)
[   47.939028] wlan0: direct probe responded
[   47.939031] wlan0: authenticate with AP b2:1c:fd:25:c0:0c (try 1)
[   47.941896] wlan0: authenticated
[   47.941913] wlan0: associate with AP b2:1c:fd:25:c0:0c (try 1)
[   47.950827] wlan0: RX AssocResp from b2:1c:fd:25:c0:0c (capab=0x411 status=0 aid=2)
[   47.950831] wlan0: associated
[   48.664050] wlan0: no IPv6 routers present
[   54.163723] wlan0: deauthenticated from b2:1c:fd:25:c0:0c (Reason: 15)
[   57.656235] wlan0: direct probe to AP b2:1c:fd:25:c0:0c (try 1)
[   57.659842] wlan0: direct probe responded
[   57.659846] wlan0: authenticate with AP b2:1c:fd:25:c0:0c (try 1)
[   57.661719] wlan0: authenticated
[   57.661814] wlan0: associate with AP b2:1c:fd:25:c0:0c (try 1)
[   57.670702] wlan0: RX AssocResp from b2:1c:fd:25:c0:0c (capab=0x411 status=0 aid=3)
[   57.670707] wlan0: associated
[   63.296040] usb 2-1: new high speed USB device using ehci_hcd and address 3
[   63.429475] usb 2-1: configuration #1 chosen from 2 choices
[   63.462374] Initializing USB Mass Storage driver...
[   63.462493] scsi6 : SCSI emulation for USB Mass Storage devices
[   63.462635] usbcore: registered new interface driver usb-storage
[   63.462638] USB Mass Storage support registered.
[   63.463755] usb-storage: device found at 3
[   63.463757] usb-storage: waiting for device to settle before scanning
[   63.891646] wlan0: deauthenticated from b2:1c:fd:25:c0:0c (Reason: 15)
[   67.341009] wlan0: direct probe to AP b2:1c:fd:25:c0:0c (try 1)
[   67.344630] wlan0: direct probe responded
[   67.344634] wlan0: authenticate with AP b2:1c:fd:25:c0:0c (try 1)
[   67.346409] wlan0: authenticated
[   67.346426] wlan0: associate with AP b2:1c:fd:25:c0:0c (try 1)
[   67.355312] wlan0: RX AssocResp from b2:1c:fd:25:c0:0c (capab=0x411 status=0 aid=3)
[   67.355315] wlan0: associated
[   68.460175] usb-storage: device scan complete
[   68.462134] scsi 6:0:0:0: Direct-Access     Apple    iPod             1.62 PQ: 0 ANSI: 0
[   68.462730] sd 6:0:0:0: Attached scsi generic sg2 type 0
[   68.474248] sd 6:0:0:0: [sdb] 946625 4096-byte logical blocks: (3.87 GB/3.61 GiB)
[   68.474742] sd 6:0:0:0: [sdb] Write Protect is off
[   68.474745] sd 6:0:0:0: [sdb] Mode Sense: 68 00 00 08
[   68.474747] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[   68.476725] sd 6:0:0:0: [sdb] 946625 4096-byte logical blocks: (3.87 GB/3.61 GiB)
[   68.477236] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[   68.477240]  sdb: sdb1
[   68.479625] sd 6:0:0:0: [sdb] 946625 4096-byte logical blocks: (3.87 GB/3.61 GiB)
[   68.480111] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[   68.480116] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[   73.578634] wlan0: deauthenticated from b2:1c:fd:25:c0:0c (Reason: 15)
[   77.016508] wlan0: direct probe to AP b2:1c:fd:25:c0:0c (try 1)
[   77.020132] wlan0: direct probe responded
[   77.020135] wlan0: authenticate with AP b2:1c:fd:25:c0:0c (try 1)
[   77.024783] wlan0: authenticated
[   77.024801] wlan0: associate with AP b2:1c:fd:25:c0:0c (try 1)
[   77.035522] wlan0: RX AssocResp from b2:1c:fd:25:c0:0c (capab=0x411 status=0 aid=2)
[   77.035526] wlan0: associated
[   83.254776] wlan0: deauthenticated from b2:1c:fd:25:c0:0c (Reason: 15)
[   86.669672] wlan0: direct probe to AP b2:1c:fd:25:c0:0c (try 1)
[   86.674600] wlan0: direct probe responded
[   86.674609] wlan0: authenticate with AP b2:1c:fd:25:c0:0c (try 1)
[   86.680940] wlan0: authenticated
[   86.680979] wlan0: associate with AP b2:1c:fd:25:c0:0c (try 1)
[   86.689887] wlan0: RX AssocResp from b2:1c:fd:25:c0:0c (capab=0x411 status=0 aid=2)
[   86.689891] wlan0: associated
[   92.923931] wlan0: deauthenticated from b2:1c:fd:25:c0:0c (Reason: 15)
[  102.619233] wlan0: direct probe to AP b2:1c:fd:25:c0:0c (try 1)
[  102.622844] wlan0: direct probe responded
[  102.622853] wlan0: authenticate with AP b2:1c:fd:25:c0:0c (try 1)
[  102.624686] wlan0: authenticated
[  102.624723] wlan0: associate with AP b2:1c:fd:25:c0:0c (try 1)
[  102.636461] wlan0: RX AssocResp from b2:1c:fd:25:c0:0c (capab=0x411 status=0 aid=3)
[  102.636465] wlan0: associated
[  102.866832] padlock: VIA PadLock not detected.
[  111.444067] CE: hpet increasing min_delta_ns to 15000 nsec
[  116.221316] iwlagn 0000:02:00.0: iwl_tx_agg_start on ra = b2:1c:fd:25:c0:0c tid = 0
[  301.104220] mmc0: card 0002 removed
[  303.203973] mmc0: new SD card at address 0002
[  303.204634] mmcblk0: mmc0:0002 SD    3.68 GiB 
[  303.204764]  mmcblk0: p1
[  710.329464] usb 2-1: USB disconnect, address 3
[  758.680578] mmc0: card 0002 removed
[  759.279284] mmc0: new SD card at address 0002
[  759.279456] mmcblk0: mmc0:0002 SD    3.68 GiB 
[  759.279519]  mmcblk0: p1
[  797.104532] CE: hpet increasing min_delta_ns to 22500 nsec
[  815.388049] usb 2-1: new high speed USB device using ehci_hcd and address 4
[  815.522325] usb 2-1: configuration #1 chosen from 1 choice
[  815.529521] scsi7 : SCSI emulation for USB Mass Storage devices
[  815.552019] usb-storage: device found at 4
[  815.552022] usb-storage: waiting for device to settle before scanning
[  815.557373] cdc_acm 2-1:1.0: This device cannot do calls on its own. It is not a modem.
[  815.557867] cdc_acm 2-1:1.0: ttyACM0: USB ACM device
[  815.558700] usbcore: registered new interface driver cdc_acm
[  815.558737] cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
[  820.554483] usb-storage: device scan complete
[  820.554978] scsi 7:0:0:0: Direct-Access     GT-I5700  - Card               PQ: 0 ANSI: 2
[  820.556890] sd 7:0:0:0: Attached scsi generic sg2 type 0
[  820.558600] sd 7:0:0:0: [sdb] Attached SCSI removable disk
[  829.505649] usb 2-1: USB disconnect, address 4
[  829.884210] usb 2-1: new high speed USB device using ehci_hcd and address 5
[  830.016468] usb 2-1: config 1 has 1 interface, different from the descriptor's value: 3
[  830.016476] usb 2-1: config 1 has no interface number 0
[  830.017189] usb 2-1: configuration #1 chosen from 1 choice
[  830.028580] scsi8 : SCSI emulation for USB Mass Storage devices
[  830.035142] usb-storage: device found at 5
[  830.035148] usb-storage: waiting for device to settle before scanning
[  835.032265] usb-storage: device scan complete
[  835.032749] scsi 8:0:0:0: Direct-Access     GT-I5700  - Card               PQ: 0 ANSI: 2
[  835.033232] sd 8:0:0:0: Attached scsi generic sg2 type 0
[  835.041987] sd 8:0:0:0: [sdb] Attached SCSI removable disk
[  923.713012] sd 8:0:0:0: [sdb] 15523840 512-byte logical blocks: (7.94 GB/7.40 GiB)
[  923.713493] sd 8:0:0:0: [sdb] Assuming drive cache: write through
[  923.728493] sd 8:0:0:0: [sdb] Assuming drive cache: write through
[  923.728510]  sdb: sdb1
[ 1106.131013] usb 2-1: USB disconnect, address 5
[ 1473.868209] usb 2-2: new high speed USB device using ehci_hcd and address 6
[ 1474.002837] usb 2-2: configuration #1 chosen from 2 choices
[ 1474.007355] scsi9 : SCSI emulation for USB Mass Storage devices
[ 1474.007718] usb-storage: device found at 6
[ 1474.007723] usb-storage: waiting for device to settle before scanning
[ 1479.004502] usb-storage: device scan complete
[ 1479.006712] scsi 9:0:0:0: Direct-Access     Apple    iPod             1.62 PQ: 0 ANSI: 0
[ 1479.007967] sd 9:0:0:0: Attached scsi generic sg2 type 0
[ 1479.020325] sd 9:0:0:0: [sdb] 946625 4096-byte logical blocks: (3.87 GB/3.61 GiB)
[ 1479.020947] sd 9:0:0:0: [sdb] Write Protect is off
[ 1479.020955] sd 9:0:0:0: [sdb] Mode Sense: 68 00 00 08
[ 1479.020961] sd 9:0:0:0: [sdb] Assuming drive cache: write through
[ 1479.022436] sd 9:0:0:0: [sdb] 946625 4096-byte logical blocks: (3.87 GB/3.61 GiB)
[ 1479.023326] sd 9:0:0:0: [sdb] Assuming drive cache: write through
[ 1479.023336]  sdb: sdb1
[ 1479.027691] sd 9:0:0:0: [sdb] 946625 4096-byte logical blocks: (3.87 GB/3.61 GiB)
[ 1479.028307] sd 9:0:0:0: [sdb] Assuming drive cache: write through
[ 1479.028317] sd 9:0:0:0: [sdb] Attached SCSI removable disk
[ 1649.880067] usb 2-1: new high speed USB device using ehci_hcd and address 7
[ 1650.012448] usb 2-1: config 1 has 1 interface, different from the descriptor's value: 3
[ 1650.012457] usb 2-1: config 1 has no interface number 0
[ 1650.013170] usb 2-1: configuration #1 chosen from 1 choice
[ 1650.027957] scsi10 : SCSI emulation for USB Mass Storage devices
[ 1650.028256] usb-storage: device found at 7
[ 1650.028258] usb-storage: waiting for device to settle before scanning
[ 1655.028402] usb-storage: device scan complete
[ 1655.029134] scsi 10:0:0:0: Direct-Access     GT-I5700  - Card          4Pv/ PQ: 0 ANSI: 2
[ 1655.030117] sd 10:0:0:0: Attached scsi generic sg3 type 0
[ 1655.034836] sd 10:0:0:0: [sdc] Attached SCSI removable disk
[ 1848.286479] usb 2-1: USB disconnect, address 7
[ 2066.032217] usb 2-1: new high speed USB device using ehci_hcd and address 8
[ 2066.165080] usb 2-1: config 1 has 1 interface, different from the descriptor's value: 3
[ 2066.165089] usb 2-1: config 1 has no interface number 0
[ 2066.166157] usb 2-1: configuration #1 chosen from 1 choice
[ 2066.172168] scsi11 : SCSI emulation for USB Mass Storage devices
[ 2066.172540] usb-storage: device found at 8
[ 2066.172545] usb-storage: waiting for device to settle before scanning
[ 2071.172483] usb-storage: device scan complete
[ 2071.173418] scsi 11:0:0:0: Direct-Access     GT-I5700  - Card          4Pv/ PQ: 0 ANSI: 2
[ 2071.174622] sd 11:0:0:0: Attached scsi generic sg3 type 0
[ 2071.192254] sd 11:0:0:0: [sdc] Attached SCSI removable disk
[ 2099.038597] usb 2-1: USB disconnect, address 8
[ 2178.900214] usb 2-1: new high speed USB device using ehci_hcd and address 9
[ 2179.033219] usb 2-1: config 1 has 1 interface, different from the descriptor's value: 3
[ 2179.033228] usb 2-1: config 1 has no interface number 0
[ 2179.034438] usb 2-1: configuration #1 chosen from 1 choice
[ 2179.040391] scsi12 : SCSI emulation for USB Mass Storage devices
[ 2179.040762] usb-storage: device found at 9
[ 2179.040767] usb-storage: waiting for device to settle before scanning
[ 2184.040477] usb-storage: device scan complete
[ 2184.041083] scsi 12:0:0:0: Direct-Access     GT-I5700  - Card          4Pv/ PQ: 0 ANSI: 2
[ 2184.052078] sd 12:0:0:0: [sdc] Attached SCSI removable disk
[ 2184.052986] sd 12:0:0:0: Attached scsi generic sg3 type 0
[ 2288.789932] usb 2-1: USB disconnect, address 9
[ 2341.224590] CE: hpet increasing min_delta_ns to 33750 nsec
[ 2471.560288] usb 2-1: new high speed USB device using ehci_hcd and address 10
[ 2471.693004] usb 2-1: config 1 has 1 interface, different from the descriptor's value: 3
[ 2471.693014] usb 2-1: config 1 has no interface number 0
[ 2471.694156] usb 2-1: configuration #1 chosen from 1 choice
[ 2471.700091] scsi13 : SCSI emulation for USB Mass Storage devices
[ 2471.700464] usb-storage: device found at 10
[ 2471.700469] usb-storage: waiting for device to settle before scanning
[ 2476.700296] usb-storage: device scan complete
[ 2476.700994] scsi 13:0:0:0: Direct-Access     GT-I5700  - Card          4Pv/ PQ: 0 ANSI: 2
[ 2476.702378] sd 13:0:0:0: Attached scsi generic sg3 type 0
[ 2476.706442] sd 13:0:0:0: [sdc] Attached SCSI removable disk
[ 4213.474841] usb 2-2: USB disconnect, address 6
[ 6289.817458] iwlagn 0000:02:00.0: RF_KILL bit toggled to disable radio.
[ 6289.817695] iwlagn 0000:02:00.0: Error sending REPLY_ADD_STA: enqueue_hcmd failed: -5
[ 6289.817703] HW problem - can not stop rx aggregation for tid 0
[ 6289.817734] iwlagn 0000:02:00.0: Error sending REPLY_RXON_ASSOC: enqueue_hcmd failed: -5
[ 6289.817741] iwlagn 0000:02:00.0: Error setting RXON_ASSOC (-5)
[ 6289.828634] wlan0: deauthenticating from b2:1c:fd:25:c0:0c by local choice (reason=3)
[ 6294.512548] iwlagn 0000:02:00.0: RF_KILL bit toggled to enable radio.
[ 6294.656788] Registered led device: iwl-phy0::radio
[ 6294.656836] Registered led device: iwl-phy0::assoc
[ 6294.656880] Registered led device: iwl-phy0::RX
[ 6294.656922] Registered led device: iwl-phy0::TX
[ 6294.683426] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 6306.405013] wlan0: deauthenticating from b2:1c:fd:25:c0:0c by local choice (reason=3)
[ 6306.405349] wlan0: direct probe to AP b2:1c:fd:25:c0:0c (try 1)
[ 6306.432119] wlan0: direct probe responded
[ 6306.432124] wlan0: authenticate with AP b2:1c:fd:25:c0:0c (try 1)
[ 6306.433828] wlan0: authenticated
[ 6306.433846] wlan0: associate with AP b2:1c:fd:25:c0:0c (try 1)
[ 6306.445856] wlan0: RX AssocResp from b2:1c:fd:25:c0:0c (capab=0x411 status=0 aid=3)
[ 6306.445859] wlan0: associated
[ 6306.447843] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 6316.836244] wlan0: no IPv6 routers present
[ 6322.581727] iwlagn 0000:02:00.0: iwl_tx_agg_start on ra = b2:1c:fd:25:c0:0c tid = 0
[ 6616.067711] usb 2-1: USB disconnect, address 10

maman

Re : Lecteur carte sd non reconnu

'lut,

Pour la commande sudo fdisk -l il me dit que c'est une commande inconnue.

c'est un "l" miinuscule, comme dans laurence.

---

90% of teens today would die if Facebook was completely destroyed. If you are one of the 10% that would be laughing, copy and paste this to your signature.

sarkan

Re : Lecteur carte sd non reconnu

fdisk -l ne me renvoie rien du tout pas de message d'erreur nada

maman

Re : Lecteur carte sd non reconnu

salut,
je ne comprends pas pourquoi "sudo fdisk -l" ne donne rien chez toi. Peut-être qu'un plus doué que moi nous renseignera.
Sinon, toujours avec la carte insérée, essaie

sudo blkid

---

90% of teens today would die if Facebook was completely destroyed. If you are one of the 10% that would be laughing, copy and paste this to your signature.

sarkan

Re : Lecteur carte sd non reconnu

pour blkid

/dev/sda1: LABEL="RM-CM-)servM-CM-) au systM-CM-(me" UUID="2E98B1A798B16DC9" TYPE="ntfs" 
/dev/sda2: UUID="CE7EBBA57EBB84AD" TYPE="ntfs" 
/dev/sda3: UUID="dc3b3a0d-fa1d-4265-a500-ec9893291836" TYPE="ext4" 
/dev/sda4: UUID="0F77AE1346C4841A" TYPE="ntfs" 
/dev/mmcblk0p1: LABEL="apn" UUID="ADA4-8EEC" TYPE="vfat"

maman

Re : Lecteur carte sd non reconnu

salut,
tu vas créer un point de montage, puis tu vas essayer de la monter à la main:

sudo mkdir /mnt/sd

sudo mount /dev/mmcblk0p1 /mnt/sd

Avec le navigateur de fichier (nautilus), tu te rends dans le répertoire /mnt/sd. Tu devrais y retrouver le contenu de ta carte.

Avant de retirer la carte, il faut la démonter:

sudo umount /mnt/sd

@+

Edit: quand tu as fait tout ça, postes aussi

dmesg

pour voir.

Dernière modification par maman (Le 26/09/2010, à 22:42)

---

90% of teens today would die if Facebook was completely destroyed. If you are one of the 10% that would be laughing, copy and paste this to your signature.