(Abandon) Ports USB non fonctionnel

Elsimate · Le 13/02/2015, à 18:58

Bonjour à tous,

Suite à de vaines recherches sur internet je fais appel à la communauté pour tenter de résoudre mon problème.

J'ai Ubuntu 14.04 installer en dual-boot avec W8.1 depuis bientôt un an (voir ma signature), tout fonctionnait bien jusqu'à tout récemment, voilà mon problème :

Si je démarre Ubuntu avec une clés usb ou tout autre périphérique préalablement monter celui-ci apparaît au lanceur et j'ai accès aux fichiers sans problème. Si j’éjecte le périphérique et que je tente de le brancher à nouveau à un port usb rien ne se produit, le périphérique ne s'affiche pas au lanceur. À cet étape les clés ou périphériques ne sont pas détectées par l'application Disks ou la commande lsusb lancée au terminal, pourtant visible lorsque préalablement monter avant le démarrage de Ubuntu.

Tout fonctionne bien sur W8.1 ou sur mon autre PC sous Xubuntu.

Le problème est probablement survenu suite une mise à jour récente de Ubuntu, qui font légion ces dernier temps... j'ai tenter un sudo apt update et un sudo apt full-upgrade sans succès.

Quelqu'un aurait-il une piste ?

Merci d'avance !

Dernière modification par Elsimate (Le 03/03/2015, à 20:43)

Bougron · Le 13/02/2015, à 20:05

Bonsoir.
Je viens de brancher et débrancher à la hussarde et aussi par la commande d'éjection puis rebrancher une clé USB sur une prise usb2 puis une prise usb3.
Ubuntu 14.04.1 est à jour. Je peux accéder sans problème au contenu de la clé USB .

Elsimate · Le 13/02/2015, à 20:43

Merci pour le suivi,

Visiblement quelque chose chez moi a foiré, reste à savoir quoi.

Sous Xubuntu, dans Paramétrage/Matériel on a accès aux paramètres des *Disques amovibles et Médias*, y a-t-il un équivalent sous Ubuntu question de voir si tout est bien paramétrer.

J'ai *Système Setting*, *Unity Tweak Tool* et *Compiz Config Setting Manager* d'installer et aucun de ceux-ci me donne accès à ces paramètres.

Merci encore !

Elsimate · Le 14/02/2015, à 02:38

Personne n'a d'idées ?

J'ai tester Ubuntu en live usb et tout fonctionne correctement, les clés sont automatiquement montées et les fichiers sont accessibles.

Elsimate · Le 15/02/2015, à 21:19

Suis-je le seul avec cet anomalie ?

De nombreuses recherche sur le net semblait jeter le dévolu sur une incomparabilité de matériel dû au nouveau noyau installer, le temps de trouver comment démarrer sur un ancien noyau et je me lance, aucun changement avec le noyau 3.13.0-44 et 43.

Je continue mes recherche encore quelque temps et si celles-ci n’aboutissent à rien je vire cette m.... de Ubuntu pour Xubuntu...

Bye !

Coeur Noir · Le 15/02/2015, à 21:31

Il a bien un "medias amovibles" dans les "détails" de "paramètres système"… pas vraiment équivalent.

Elsimate · Le 15/02/2015, à 21:49

Salut Coeur Noir,

Effectivement, j'avais vu, mais comme tu mentionnes, pas vraiment équivalent.

Bye !

Elsimate · Le 17/02/2015, à 03:06

Je cherche encore...

Voilà qui me semblait prometteur, exactement mon problème, mais non... ça fonctionne pas chez-moi

http://forum.ubuntu-fr.org/viewtopic.php?id=1344411

C'est pas que ce soit très embêtant, mais il doit bien avoir une solution, après tout, tout n'est qu'une succession de 0 et de 1

J5012 · Le 17/02/2015, à 04:35

ca s'appelle chez toi "ejecter" ou "retirer..." ?

sur mon acer en 14.04, j'ai les deux ... si je choisis "retirer" comme sur mon pbell en 12.04, le periph usb disparait
je dois choisir "ejecter" ... au contraire sur le 12.04 "retirer" fait ejecter la cle ...

que raconte udisks une fois rebranchée la cle ?

udisks --enumerate

Elsimate · Le 17/02/2015, à 16:04

Bonjour J5012,
J'ai aussi les deux choix, "retirer du lanceur" et "éjecter" je dois sélectionner ce "Éjecter" pour démonter la clé, si je sélectionne "Retirer du lanceur" la clé et son contenu sont encore visible dans "Fichiers".

J'ai deux prises usb 2.0 et deux usb 3.0, je viens de démarrer mon système avec une clé d'insérer dans un port usb 2.0 et une autre dans un port usb 3.0, nommons les A, les deux sont visibles après démarrage et le contenu est accessible, au clic droit sur celles-ci j'ai l'option "Retirer du lanceur" et "Éjecter".
Aussi longtemps que je laisse ces deux clés A brancher je peux utiliser les deux autres ports libres sans souci, je monte et démonte des clés B à répétition sans problème aucun, et, comme si cela ne suffisait pas, une troisième option s'ajoute au clic droit sur les clés B seulement "Retirer en toute sécurité" qui a le même effet que "Éjecter" si j'éjecte toutes les clés, plus aucun port usb n'est fonctionnel.

Je viens d'éjecter toutes les clés et d'en rebrancher une sur un port usb 2.0 et une autre à un port usb 3.0, aucune des deux n'est visible au lanceur ni dans "Fichiers" et voici le retour de la commande :

ubuntu@Aspire:~$ udisks --enumerate
/org/freedesktop/UDisks/devices/sr0
/org/freedesktop/UDisks/devices/sda1
/org/freedesktop/UDisks/devices/sda2
/org/freedesktop/UDisks/devices/sda3
/org/freedesktop/UDisks/devices/sda4
/org/freedesktop/UDisks/devices/sda5
/org/freedesktop/UDisks/devices/sda6
/org/freedesktop/UDisks/devices/sda
/org/freedesktop/UDisks/devices/sda7
/org/freedesktop/UDisks/devices/sda8
/org/freedesktop/UDisks/devices/sda9
/org/freedesktop/UDisks/devices/sdd
ubuntu@Aspire:~$

Voilà, merci pour le suivi !

@+ Elsimate

J5012 · Le 17/02/2015, à 22:42

quel ordi c'est dans ta signature ou est-ce un autre ?

ton bug me rappelle les premiers acer one aspire dont les inserts sdcard se comportaient d'une facon similaire : si aucune memoire n'etaient inseree, le port n'etait pas detecté ...

Elsimate · Le 17/02/2015, à 23:32

C'est le deuxième, à noter que le problème n'est apparu que récemment.

J'ai lu quelques cas semblables sur le net sans être totalement identiques, mais rien de très récent, comme ceci :

http://www.hosthis.org/2011/06/linux-et … s-usb-2-0/

On peut y lire : " quasiment tous les postes que je trouves expliquent le problème par un bug dans le module ehci_hcd qui gère l’usb 2 "

@+ Elsimate

J5012 · Le 18/02/2015, à 00:19

ce tuto : http://www.hosthis.org/2011/06/linux-et … s-usb-2-0/
est l'explication detaillée et globale de la discussion forum : http://forum.ubuntu-fr.org/viewtopic.php?id=1344411
que tu as essayé et qui ne marche pas ...

as-tu essayé le tuto qui est plus global, qui te permet de trouver les propres identifiants materiels usb2 concernant ton ordi ... ?

Elsimate · Le 18/02/2015, à 02:46

Oui j'ai tenter de le faire, mais comme l'article date de 2011 la plupart des commandes ne sont plus reconnues au terminal.

Pas contre jai pu identifier les ports avec la commande :

ubuntu@Aspire:~$ cd /sys/bus/pci/drivers/ehci-pci
ubuntu@Aspire:/sys/bus/pci/drivers/ehci-pci$ ls
0000:00:12.2  0000:00:13.2  bind  new_id  remove_id  uevent  unbind

Ce qui correspond à ce qu'on retrouve dans mon fichier : /sys/bus/pci/drivers/ehci-pci

Ensuite les commandes suggérées ne répondent plus et comme mes connaissances sont plutôt basique je sèche...

J'ai tenter la manœuvre de http://forum.ubuntu-fr.org/viewtopic.php?id=1344411 avec les deux identifiants sans aucun résultats sur les ports usb 2 ou usb 3

J'ai cru comprendre que la commande "dmesg" pouvait aider à identifier un problème, voici le résultat avec une clée montée au démarrage sur un port usb3 et une montée après démarrage à un port usb 2 :

[    0.841734] ohci-pci 0000:00:14.5: new USB bus registered, assigned bus number 5
[    0.841750] ohci-pci 0000:00:14.5: irq 18, io mem 0xfeb4c000
[    0.901222] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[    0.901225] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.901227] usb usb5: Product: OHCI PCI host controller
[    0.901229] usb usb5: Manufacturer: Linux 3.13.0-45-generic ohci_hcd
[    0.901230] usb usb5: SerialNumber: 0000:00:14.5
[    0.901383] hub 5-0:1.0: USB hub found
[    0.901390] hub 5-0:1.0: 2 ports detected
[    0.901473] ohci-platform: OHCI generic platform driver
[    0.901483] uhci_hcd: USB Universal Host Controller Interface driver
[    0.901635] xhci_hcd 0000:00:10.0: xHCI Host Controller
[    0.901639] xhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 6
[    0.901850] xhci_hcd 0000:00:10.0: irq 44 for MSI/MSI-X
[    0.901858] xhci_hcd 0000:00:10.0: irq 45 for MSI/MSI-X
[    0.901864] xhci_hcd 0000:00:10.0: irq 46 for MSI/MSI-X
[    0.901870] xhci_hcd 0000:00:10.0: irq 47 for MSI/MSI-X
[    0.901877] xhci_hcd 0000:00:10.0: irq 48 for MSI/MSI-X
[    0.901976] usb usb6: New USB device found, idVendor=1d6b, idProduct=0002
[    0.901978] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.901979] usb usb6: Product: xHCI Host Controller
[    0.901980] usb usb6: Manufacturer: Linux 3.13.0-45-generic xhci_hcd
[    0.901982] usb usb6: SerialNumber: 0000:00:10.0
[    0.902053] hub 6-0:1.0: USB hub found
[    0.902060] hub 6-0:1.0: 2 ports detected
[    0.902114] xhci_hcd 0000:00:10.0: xHCI Host Controller
[    0.902116] xhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 7
[    0.905271] usb usb7: New USB device found, idVendor=1d6b, idProduct=0003
[    0.905280] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.905281] usb usb7: Product: xHCI Host Controller
[    0.905282] usb usb7: Manufacturer: Linux 3.13.0-45-generic xhci_hcd
[    0.905283] usb usb7: SerialNumber: 0000:00:10.0
[    0.905357] hub 7-0:1.0: USB hub found
[    0.905365] hub 7-0:1.0: 2 ports detected
[    0.913430] xhci_hcd 0000:00:10.1: xHCI Host Controller
[    0.913437] xhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 8
[    0.913651] xhci_hcd 0000:00:10.1: irq 49 for MSI/MSI-X
[    0.913657] xhci_hcd 0000:00:10.1: irq 50 for MSI/MSI-X
[    0.913664] xhci_hcd 0000:00:10.1: irq 51 for MSI/MSI-X
[    0.913674] xhci_hcd 0000:00:10.1: irq 52 for MSI/MSI-X
[    0.913680] xhci_hcd 0000:00:10.1: irq 53 for MSI/MSI-X
[    0.913797] usb usb8: New USB device found, idVendor=1d6b, idProduct=0002
[    0.913799] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.913800] usb usb8: Product: xHCI Host Controller
[    0.913801] usb usb8: Manufacturer: Linux 3.13.0-45-generic xhci_hcd
[    0.913803] usb usb8: SerialNumber: 0000:00:10.1
[    0.913933] hub 8-0:1.0: USB hub found
[    0.913940] hub 8-0:1.0: 2 ports detected
[    0.914006] xhci_hcd 0000:00:10.1: xHCI Host Controller
[    0.914009] xhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 9
[    0.917050] usb usb9: New USB device found, idVendor=1d6b, idProduct=0003
[    0.917051] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.917052] usb usb9: Product: xHCI Host Controller
[    0.917053] usb usb9: Manufacturer: Linux 3.13.0-45-generic xhci_hcd
[    0.917054] usb usb9: SerialNumber: 0000:00:10.1
[    0.917145] hub 9-0:1.0: USB hub found
[    0.917159] hub 9-0:1.0: 2 ports detected
[    0.925342] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[    0.925345] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[    0.925528] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.925663] mousedev: PS/2 mouse device common for all mice
[    0.925783] rtc_cmos 00:07: RTC can wake from S4
[    0.925885] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
[    0.925906] rtc_cmos 00:07: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[    0.925965] device-mapper: uevent: version 1.0.3
[    0.926045] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com
[    0.926054] ledtrig-cpu: registered to indicate activity on CPUs
[    0.926055] EFI Variables Facility v0.08 2004-May-17
[    0.932376] TCP: cubic registered
[    0.932469] NET: Registered protocol family 10
[    0.932606] NET: Registered protocol family 17
[    0.932612] Key type dns_resolver registered
[    0.932978] Loading compiled-in X.509 certificates
[    0.933718] Loaded X.509 cert 'Magrathea: Glacier signing key: 34992139f3da40b620bd5517597ba85af5797c9a'
[    0.933729] registered taskstats version 1
[    0.935996] Key type trusted registered
[    0.937749] Key type encrypted registered
[    0.939285] AppArmor: AppArmor sha1 policy hashing enabled
[    0.939288] IMA: No TPM chip found, activating TPM-bypass!
[    0.939550] regulator-dummy: disabling
[    0.939700]   Magic number: 3:742:645
[    0.939781] rtc_cmos 00:07: setting system clock to 2015-02-17 18:37:00 UTC (1424198220)
[    0.939911] acpi-cpufreq: overriding BIOS provided _PSD data
[    0.940086] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    0.940087] EDD information not available.
[    0.940127] PM: Hibernation image not present or could not be loaded.
[    0.941295] Freeing unused kernel memory: 1336K (ffffffff81d20000 - ffffffff81e6e000)
[    0.941297] Write protecting the kernel read-only data: 12288k
[    0.943791] Freeing unused kernel memory: 796K (ffff880001739000 - ffff880001800000)
[    0.945928] Freeing unused kernel memory: 688K (ffff880001b54000 - ffff880001c00000)
[    0.954145] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2
[    0.958777] systemd-udevd[117]: starting version 204
[    0.974353] wmi: Mapper loaded
[    0.976658] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    0.976882] r8169 0000:01:00.0: irq 54 for MSI/MSI-X
[    0.977016] r8169 0000:01:00.0 eth0: RTL8168f/8111f at 0xffffc90000c5a000, 54:be:f7:25:a0:af, XID 08100800 IRQ 54
[    0.977017] r8169 0000:01:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[    0.980317] ahci 0000:00:11.0: version 3.0
[    0.980487] ahci 0000:00:11.0: irq 55 for MSI/MSI-X
[    0.980491] ahci 0000:00:11.0: irq 56 for MSI/MSI-X
[    0.980495] ahci 0000:00:11.0: irq 57 for MSI/MSI-X
[    0.980499] ahci 0000:00:11.0: irq 58 for MSI/MSI-X
[    0.980503] ahci 0000:00:11.0: irq 59 for MSI/MSI-X
[    0.980507] ahci 0000:00:11.0: irq 60 for MSI/MSI-X
[    0.980511] ahci 0000:00:11.0: irq 61 for MSI/MSI-X
[    0.980517] ahci 0000:00:11.0: irq 62 for MSI/MSI-X
[    0.980577] ahci 0000:00:11.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x11 impl SATA mode
[    0.980580] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part 
[    0.982021] scsi0 : ahci
[    0.982173] scsi1 : ahci
[    0.982253] scsi2 : ahci
[    0.982326] scsi3 : ahci
[    0.982425] scsi4 : ahci
[    0.982467] ata1: SATA max UDMA/133 abar m2048@0xfeb51000 port 0xfeb51100 irq 55
[    0.982468] ata2: DUMMY
[    0.982469] ata3: DUMMY
[    0.982470] ata4: DUMMY
[    0.982472] ata5: SATA max UDMA/133 abar m2048@0xfeb51000 port 0xfeb51300 irq 59
[    1.021180] usb 1-1: new high-speed USB device number 2 using ehci-pci
[    1.159831] usb 1-1: New USB device found, idVendor=04a9, idProduct=2774
[    1.159835] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    1.159836] usb 1-1: Product: MF4700 Series
[    1.159838] usb 1-1: Manufacturer: Canon Inc
[    1.159839] usb 1-1: SerialNumber: 0147824E4C26
[    1.272937] usb 1-2: new high-speed USB device number 3 using ehci-pci
[    1.411750] usb 1-2: New USB device found, idVendor=03f0, idProduct=1424
[    1.411754] usb 1-2: New USB device strings: Mfr=10, Product=11, SerialNumber=0
[    1.411756] usb 1-2: Product: f2105 2PORT USB 2.0 HUB
[    1.411757] usb 1-2: Manufacturer: HP\xffffffc3\xffffffbf\xffffffbf
[    1.413195] hub 1-2:1.0: USB hub found
[    1.413743] hub 1-2:1.0: 2 ports detected
[    1.472662] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    1.472690] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.473526] ata1.00: ATA-8: ST1000DM003-1CH162, CC44, max UDMA/133
[    1.473530] ata1.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    1.474472] ata1.00: configured for UDMA/133
[    1.474609] scsi 0:0:0:0: Direct-Access     ATA      ST1000DM003-1CH1 CC44 PQ: 0 ANSI: 5
[    1.474764] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[    1.474766] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    1.474774] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.474829] sd 0:0:0:0: [sda] Write Protect is off
[    1.474832] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.474858] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.486349] ata5.00: ATAPI: MATSHITA DVD-RAM SW830, 1.00, max UDMA/100
[    1.502231] ata5.00: configured for UDMA/100
[    1.509170] scsi 4:0:0:0: CD-ROM            MATSHITA DVD-RAM SW830    1.00 PQ: 0 ANSI: 5
[    1.520429] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[    1.520433] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.520580] sr 4:0:0:0: Attached scsi CD-ROM sr0
[    1.520653] sr 4:0:0:0: Attached scsi generic sg1 type 5
[    1.531501]  sda: sda1 sda2 sda3 sda4 sda5 sda6 sda7 sda8 sda9
[    1.532131] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.664453] tsc: Refined TSC clocksource calibration: 3693.097 MHz
[    1.840375] usb 2-1: new high-speed USB device number 2 using ehci-pci
[    1.973178] usb 2-1: New USB device found, idVendor=0bda, idProduct=0129
[    1.973182] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    1.973184] usb 2-1: Product: USB2.0-CRW
[    1.973185] usb 2-1: Manufacturer: Generic
[    1.973186] usb 2-1: SerialNumber: 20100201396000000
[    2.084019] usb 8-2: new high-speed USB device number 2 using xhci_hcd
[    2.103081] usb 8-2: New USB device found, idVendor=08ec, idProduct=0012
[    2.103085] usb 8-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    2.103087] usb 8-2: Product: Store 'n' Go
[    2.103088] usb 8-2: Manufacturer: Verbatim
[    2.103089] usb 8-2: SerialNumber: 07105C40D2E2796C
[    2.105937] usb-storage 8-2:1.0: USB Mass Storage device detected
[    2.106036] scsi5 : usb-storage 8-2:1.0
[    2.106093] usbcore: registered new interface driver usb-storage
[    2.491651] usb 3-4: new low-speed USB device number 2 using ohci-pci
[    2.658587] usb 3-4: New USB device found, idVendor=046d, idProduct=c077
[    2.658591] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.658593] usb 3-4: Product: USB Optical Mouse
[    2.658594] usb 3-4: Manufacturer: Logitech
[    2.663027] hidraw: raw HID events driver (C) Jiri Kosina
[    2.663541] Switched to clocksource tsc
[    2.668629] usbcore: registered new interface driver usbhid
[    2.668632] usbhid: USB HID core driver
[    2.669974] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:12.0/usb3/3-4/3-4:1.0/input/input3
[    2.670098] hid-generic 0003:046D:C077.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:12.0-4/input0
[    2.923216] usb 3-5: new full-speed USB device number 3 using ohci-pci
[    3.096148] usb 3-5: string descriptor 0 read error: -22
[    3.096154] usb 3-5: New USB device found, idVendor=04ca, idProduct=3006
[    3.096156] usb 3-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    3.103713] scsi 5:0:0:0: Direct-Access     VBTM     Store 'n' Go     4.90 PQ: 0 ANSI: 0 CCS
[    3.104094] sd 5:0:0:0: Attached scsi generic sg2 type 0
[    3.104109] sd 5:0:0:0: [sdb] 497664 512-byte logical blocks: (254 MB/243 MiB)
[    3.104233] sd 5:0:0:0: [sdb] Write Protect is off
[    3.104236] sd 5:0:0:0: [sdb] Mode Sense: 45 00 00 08
[    3.104657] sd 5:0:0:0: [sdb] No Caching mode page found
[    3.104660] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[    3.105347] sd 5:0:0:0: [sdb] No Caching mode page found
[    3.105349] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[    3.106949]  sdb: sdb1
[    3.107852] sd 5:0:0:0: [sdb] No Caching mode page found
[    3.107854] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[    3.107856] sd 5:0:0:0: [sdb] Attached SCSI removable disk
[    3.336746] random: nonblocking pool is initialized
[    3.836683] EXT4-fs (sda7): mounted filesystem with ordered data mode. Opts: (null)
[   10.506119] Adding 8191996k swap on /dev/sda8.  Priority:-1 extents:1 across:8191996k FS
[   10.606638] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   10.648330] systemd-udevd[338]: starting version 204
[   10.789726] lp: driver loaded but no devices found
[   10.795234] ppdev: user-space parallel port driver
[   10.814171] AMD IOMMUv2 driver by Joerg Roedel <joerg.roedel@amd.com>
[   10.819949] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   10.820832] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[   10.820837] Disabling lock debugging due to kernel taint
[   10.829119] fglrx: module verification failed: signature and/or  required key missing - tainting kernel
[   10.837108] <6>[fglrx] Maximum main memory to use for locked dma buffers: 6880 MBytes.
[   10.837201] <6>[fglrx]   vendor: 1002 device: 990c count: 1
[   10.837522] <6>[fglrx] IOMMU is enabled, CrossFire are not supported on this platform
[   10.837523] <6>[fglrx] Disable IOMMU in BIOS options or kernel boot parameters to support CF
[   10.837653] <6>[fglrx] ioport: bar 1, base 0xf000, size: 0x100
[   10.838155] <6>[fglrx] Kernel PAT support is enabled
[   10.838176] <6>[fglrx] module loaded - fglrx 13.35.5 [Mar 12 2014] with 1 minors
[   10.838835] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[   10.838879] piix4_smbus 0000:00:14.0: Auxiliary SMBus Host Controller at 0xb20
[   10.854338] cfg80211: Calling CRDA to update world regulatory domain
[   10.886003] Bluetooth: Core ver 2.17
[   10.886030] NET: Registered protocol family 31
[   10.886031] Bluetooth: HCI device and connection manager initialized
[   10.886040] Bluetooth: HCI socket layer initialized
[   10.886042] Bluetooth: L2CAP socket layer initialized
[   10.886046] Bluetooth: SCO socket layer initialized
[   10.887512] usbcore: registered new interface driver btusb
[   10.889947] type=1400 audit(1424216230.453:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/sbin/dhclient" pid=447 comm="apparmor_parser"
[   10.889954] type=1400 audit(1424216230.453:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=447 comm="apparmor_parser"
[   10.889958] type=1400 audit(1424216230.453:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=447 comm="apparmor_parser"
[   10.890319] type=1400 audit(1424216230.453:5): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=447 comm="apparmor_parser"
[   10.890325] type=1400 audit(1424216230.453:6): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=447 comm="apparmor_parser"
[   10.890515] type=1400 audit(1424216230.453:7): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=447 comm="apparmor_parser"
[   10.892193] ath9k 0000:04:00.0: enabling device (0000 -> 0002)
[   10.895600] snd_hda_intel 0000:00:01.1: enabling device (0000 -> 0002)
[   10.895755] hda-intel 0000:00:01.1: Using LPIB position fix
[   10.895757] hda-intel 0000:00:01.1: Force to non-snoop mode
[   10.895800] snd_hda_intel 0000:00:01.1: irq 63 for MSI/MSI-X
[   10.898167] hda-intel 0000:00:01.1: Enable sync_write for stable communication
[   10.902553] ath: phy0: ASPM enabled: 0x43
[   10.902558] ath: EEPROM regdomain: 0x6a
[   10.902559] ath: EEPROM indicates we should expect a direct regpair map
[   10.902562] ath: Country alpha2 being used: 00
[   10.902563] ath: Regpair used: 0x6a
[   10.903333] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.1/sound/card0/input4
[   10.903402] WARNING! power/level is deprecated; use power/control instead
[   10.905165] hda-intel 0000:00:14.2: Using LPIB position fix
[   10.909516] hda-intel 0000:00:14.2: Enable sync_write for stable communication
[   10.913134] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   10.913470] ieee80211 phy0: Atheros AR9462 Rev:2 mem=0xffffc90011b00000, irq=18
[   10.919664] hda_codec: ALC662 rev3: SKU not ready 0x411111f0
[   10.919899] autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:line
[   10.919900]    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   10.919902]    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[   10.919903]    mono: mono_out=0x0
[   10.919904]    inputs:
[   10.919906]      Front Mic=0x19
[   10.919908]      Rear Mic=0x18
[   10.919909]      Line=0x1a
[   10.919910] realtek: No valid SSID, checking pincfg 0x411111f0 for NID 0x1d
[   10.919911] realtek: Enable default setup for auto mode as fallback
[   10.924703] kvm: Nested Virtualization enabled
[   10.924707] kvm: Nested Paging enabled
[   10.929386] input: HD-Audio Generic Front Headphone as /devices/pci0000:00/0000:00:14.2/sound/card1/input9
[   10.929472] input: HD-Audio Generic Line Out as /devices/pci0000:00/0000:00:14.2/sound/card1/input8
[   10.929536] input: HD-Audio Generic Line as /devices/pci0000:00/0000:00:14.2/sound/card1/input7
[   10.929643] input: HD-Audio Generic Rear Mic as /devices/pci0000:00/0000:00:14.2/sound/card1/input6
[   10.929703] input: HD-Audio Generic Front Mic as /devices/pci0000:00/0000:00:14.2/sound/card1/input5
[   11.132090] cfg80211: World regulatory domain updated:
[   11.132094] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   11.132096] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   11.132097] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   11.132099] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   11.132100] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   11.132101] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   11.145239] usb 3-5: USB disconnect, device number 3
[   11.146251] usbcore: registered new interface driver ath3k
[   11.802403] rts5139: module is from the staging directory, the quality is unknown, you have been warned.
[   11.806443] scsi6 : SCSI emulation for RTS5139 USB card reader
[   11.806567] usbcore: registered new interface driver rts5139
[   11.806619] scsi 6:0:0:0: Direct-Access     Generic- xD/SD/M.S.       1.00 PQ: 0 ANSI: 0 CCS
[   11.807043] sd 6:0:0:0: Attached scsi generic sg3 type 0
[   11.898940] sd 6:0:0:0: [sdc] Attached SCSI removable disk
[   12.058183] usb 3-5: new full-speed USB device number 4 using ohci-pci
[   12.231118] usb 3-5: string descriptor 0 read error: -22
[   12.231125] usb 3-5: New USB device found, idVendor=04ca, idProduct=3006
[   12.231127] usb 3-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   13.169556] EXT4-fs (sda7): re-mounted. Opts: errors=remount-ro
[   13.296783] usblp 1-1:1.1: usblp1: USB Bidirectional printer dev 2 if 1 alt 0 proto 2 vid 0x04A9 pid 0x2774
[   13.298889] usblp 1-1:1.2: usblp2: USB Bidirectional printer dev 2 if 2 alt 0 proto 2 vid 0x04A9 pid 0x2774
[   13.298925] usbcore: registered new interface driver usblp
[   13.886091] EXT4-fs (sda9): mounted filesystem with ordered data mode. Opts: (null)
[   15.628324] init: failsafe main process (866) killed by TERM signal
[   15.708158] init: Failed to spawn ofono main process: unable to execute: No such file or directory
[   15.752704] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   15.752707] Bluetooth: BNEP filters: protocol multicast
[   15.752716] Bluetooth: BNEP socket layer initialized
[   15.758516] Bluetooth: RFCOMM TTY layer initialized
[   15.758527] Bluetooth: RFCOMM socket layer initialized
[   15.758533] Bluetooth: RFCOMM ver 1.11
[   15.926049] type=1400 audit(1424216235.493:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/cups/backend/cups-pdf" pid=1026 comm="apparmor_parser"
[   15.926056] type=1400 audit(1424216235.493:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/cupsd" pid=1026 comm="apparmor_parser"
[   15.926392] type=1400 audit(1424216235.497:10): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=1026 comm="apparmor_parser"
[   15.955427] type=1400 audit(1424216235.525:11): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/sbin/dhclient" pid=1076 comm="apparmor_parser"
[   15.955436] type=1400 audit(1424216235.525:12): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1076 comm="apparmor_parser"
[   15.955441] type=1400 audit(1424216235.525:13): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=1076 comm="apparmor_parser"
[   15.955750] type=1400 audit(1424216235.525:14): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/lightdm/lightdm-guest-session" pid=1075 comm="apparmor_parser"
[   15.955759] type=1400 audit(1424216235.525:15): apparmor="STATUS" operation="profile_load" profile="unconfined" name="chromium" pid=1075 comm="apparmor_parser"
[   15.955804] type=1400 audit(1424216235.525:16): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1076 comm="apparmor_parser"
[   15.955809] type=1400 audit(1424216235.525:17): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=1076 comm="apparmor_parser"
[   16.101472] init: cups main process (1029) killed by HUP signal
[   16.101483] init: cups main process ended, respawning
[   16.603794] Non-volatile memory driver v1.3
[   16.704322] r8169 0000:01:00.0 eth0: link down
[   16.704343] r8169 0000:01:00.0 eth0: link down
[   16.704384] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   16.704688] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   16.756337] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   16.759629] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   18.311187] r8169 0000:01:00.0 eth0: link up
[   18.311197] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   18.529956] fglrx_pci 0000:00:01.0: irq 64 for MSI/MSI-X
[   18.530697] <6>[fglrx] Firegl kernel thread PID: 1457
[   18.530797] <6>[fglrx] Firegl kernel thread PID: 1458
[   18.530867] <6>[fglrx] Firegl kernel thread PID: 1459
[   18.530973] <6>[fglrx] IRQ 64 Enabled
[   18.534316] <6>[fglrx] Reserved FB block: Shared offset:0, size:1000000 
[   18.534318] <6>[fglrx] Reserved FB block: Unshared offset:fb78000, size:4000 
[   18.534320] <6>[fglrx] Reserved FB block: Unshared offset:fb7c000, size:484000 
[   18.534321] <6>[fglrx] Reserved FB block: Unshared offset:2ffee000, size:12000 
[   19.075319] init: plymouth-upstart-bridge main process ended, respawning
[   19.080531] init: plymouth-upstart-bridge main process (1464) terminated with status 1
[   19.080542] init: plymouth-upstart-bridge main process ended, respawning
[   45.963408] audit_printk_skb: 132 callbacks suppressed
[   45.963411] type=1400 audit(1424216265.570:62): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/cups/backend/cups-pdf" pid=2347 comm="apparmor_parser"
[   45.963417] type=1400 audit(1424216265.570:63): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=2347 comm="apparmor_parser"
[   45.963726] type=1400 audit(1424216265.570:64): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=2347 comm="apparmor_parser"
[   47.262046] usb 8-1: new high-speed USB device number 3 using xhci_hcd
[   47.611516] usb 8-1: New USB device found, idVendor=05dc, idProduct=a817
[   47.611519] usb 8-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   47.611521] usb 8-1: Product: JumpDrive
[   47.611522] usb 8-1: Manufacturer: Lexar
[   47.611524] usb 8-1: SerialNumber: AA4YMJ17LTNBAUCT
[   47.611699] usb 8-1: ep 0x81 - rounding interval to 128 microframes, ep desc says 255 microframes
[   47.611706] usb 8-1: ep 0x2 - rounding interval to 128 microframes, ep desc says 255 microframes
[   47.612412] usb-storage 8-1:1.0: USB Mass Storage device detected
[   47.612471] scsi7 : usb-storage 8-1:1.0
[   49.159212] scsi 7:0:0:0: Direct-Access     Lexar    JumpDrive        1100 PQ: 0 ANSI: 0 CCS
[   49.159454] sd 7:0:0:0: Attached scsi generic sg4 type 0
[   49.637504] sd 7:0:0:0: [sdd] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
[   49.638373] sd 7:0:0:0: [sdd] Write Protect is off
[   49.638376] sd 7:0:0:0: [sdd] Mode Sense: 43 00 00 00
[   49.639308] sd 7:0:0:0: [sdd] No Caching mode page found
[   49.639313] sd 7:0:0:0: [sdd] Assuming drive cache: write through
[   49.641848] sd 7:0:0:0: [sdd] No Caching mode page found
[   49.641854] sd 7:0:0:0: [sdd] Assuming drive cache: write through
[   49.642789]  sdd: sdd1
[   49.645274] sd 7:0:0:0: [sdd] No Caching mode page found
[   49.645279] sd 7:0:0:0: [sdd] Assuming drive cache: write through
[   49.645283] sd 7:0:0:0: [sdd] Attached SCSI removable disk
[   49.844762] FAT-fs (sdd1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[   52.852958] systemd-hostnamed[2397]: Warning: nss-myhostname is not installed. Changing the local hostname might make it unresolveable. Please install nss-myhostname!
[   74.464841] sdd: detected capacity change from 16039018496 to 0
[   83.151118] usb 8-1: USB disconnect, device number 3
[   90.657358] usb 8-1: new high-speed USB device number 4 using xhci_hcd
[   91.010718] usb 8-1: New USB device found, idVendor=05dc, idProduct=a817
[   91.010723] usb 8-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   91.010726] usb 8-1: Product: JumpDrive
[   91.010728] usb 8-1: Manufacturer: Lexar
[   91.010729] usb 8-1: SerialNumber: AA4YMJ17LTNBAUCT
[   91.010835] usb 8-1: ep 0x81 - rounding interval to 128 microframes, ep desc says 255 microframes
[   91.010839] usb 8-1: ep 0x2 - rounding interval to 128 microframes, ep desc says 255 microframes
[   91.011501] usb-storage 8-1:1.0: USB Mass Storage device detected
[   91.012008] scsi8 : usb-storage 8-1:1.0
[   92.709910] scsi 8:0:0:0: Direct-Access     Lexar    JumpDrive        1100 PQ: 0 ANSI: 0 CCS
[   92.710424] sd 8:0:0:0: Attached scsi generic sg4 type 0
[   93.666989] sd 8:0:0:0: [sdd] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
[   93.667907] sd 8:0:0:0: [sdd] Write Protect is off
[   93.667916] sd 8:0:0:0: [sdd] Mode Sense: 43 00 00 00
[   93.668813] sd 8:0:0:0: [sdd] No Caching mode page found
[   93.668823] sd 8:0:0:0: [sdd] Assuming drive cache: write through
[   93.671421] sd 8:0:0:0: [sdd] No Caching mode page found
[   93.671429] sd 8:0:0:0: [sdd] Assuming drive cache: write through
[   93.672441]  sdd: sdd1
[   93.675174] sd 8:0:0:0: [sdd] No Caching mode page found
[   93.675183] sd 8:0:0:0: [sdd] Assuming drive cache: write through
[   93.675188] sd 8:0:0:0: [sdd] Attached SCSI removable disk
[   93.892551] FAT-fs (sdd1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[  109.347808] sdd: detected capacity change from 16039018496 to 0
[  123.949773] usb 8-1: USB disconnect, device number 4
[ 1771.754616] systemd-hostnamed[4629]: Warning: nss-myhostname is not installed. Changing the local hostname might make it unresolveable. Please install nss-myhostname!
ubuntu@Aspire:~$

Vers la fin on peut lire :

[   93.892551] FAT-fs (sdd1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.

Si je tente un "fsck" on me prévient qu'il y a risque d'endommager le périphérique, j'ai abandonner.

Merci pour votre attention et tant pis si on ne trouve pas la solution...

@+ Elsimate

Edit : Un autre cas qui utilise la méthode suggérée : http://forum.ubuntu-fr.org/viewtopic.php?id=1345241

Dernière modification par Elsimate (Le 18/02/2015, à 02:59)

J5012 · Le 18/02/2015, à 22:45

les commandes lspci , grep , tail , etc utilisees dans le tuto global sont toujours disponibles
mais la notation recherchée EHCI en majuscules n'existe que pour certains materiels, ca n'est pas du tout une notation normalisée obligatoire, un lspci simple t'aurait permis d'identifier le materiel mais il aurait fallu lire toutes les lignes de sorties, ce qui ne doit pas poser problemes puisque tu l'as fait avec les longues lignes de dmesg ...

et que tu as trouvé l'erreur ... ton probleme n'est donc pas au niveau reconnaissance materiel (ta cle usb lexar est bien detectée), et tu n'a plus le bug ehci puisqu'il s'agit d'un autre pilote xhci_...

ta cle usb designée par le peripherique sdd est d'apres detection en systeme de fichiers FAT
le systeme voit une erreur et te recommande de reparer

tu fais un fsck dessus, on te donne les prevenances habituelles pour ce genre de manipulation ... si tu ne fais rien la cle restera en l'etat jusqu'a ce que le probleme s'aggrave → perte des donnees ...

à toi de voir si ca vaut le coup ...

Bougron · Le 19/02/2015, à 10:45

Elsimate a écrit :

O
Vers la fin on peut lire :
[   93.892551] FAT-fs (sdd1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
Si je tente un "fsck" on me prévient qu'il y a risque d'endommager le périphérique, j'ai abandonner.
Merci pour votre attention et tant pis si on ne trouve pas la solution...
@+ Elsimate
Edit : Un autre cas qui utilise la méthode suggérée : http://forum.ubuntu-fr.org/viewtopic.php?id=1345241

Bonjour.
Il y a surtout écrit
93.892551] FAT-fs (sdd1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 109.347808] sdd: detected capacity change from 16039018496 to 0
C'est pour cela que tu ne peux accéder à tes données.
Je ne connais pas leur importance.

Si elles sont très importantes, tu peux choisir de dupliquer via la commande "dd" le disque en l'état.

Puis entreprendre la réparation par fsck. Rien ne prouve que cela va foirer.

Si cela ne marche pas, tu peux utiliser testdisk pour sauver le maxima de données récupérables puis reformater le disque.

Si tu disposes d'un autre micro équipé de windows, tu peux tenter de faire faire un contrôle de ce disque par windows.

Dernière modification par Bougron (Le 19/02/2015, à 10:56)

Elsimate · Le 19/02/2015, à 16:37

Bonjour, les choses se compliquent...j'ai dû faire de nombreux essais afin de bien cerner la manipulation qui entraîne le message d'erreur.

Première précision, j'ai accès aux données de mes clés USB en tout temps et aucune données n'est corrompues.

Ce que je dois faire pour que le message d'erreur s'affiche:

Démarrer mon système avec une clé insérer sur un port USB (USB3.0 dans ce cas), une fois en marche j'insère une autre clé USB dans l'autre port USB3.0, la clé est montée et j'ai accès au fichiers, si à ce stage je lance un " dmesg" au terminal, rien d'anormal.
J'éjecte la clé par un clique droit sur l'icône de celle-ci au lanceur, le message d'éjection me confirme que tout s'est bien dérouler, j'enlève la clé, je lance un second "dmesg" et voila, le message d'erreur est apparu :

[  107.099895] sd 7:0:0:0: [sdd] Write Protect is off
[  107.099904] sd 7:0:0:0: [sdd] Mode Sense: 23 00 00 00
[  107.100817] sd 7:0:0:0: [sdd] No Caching mode page found
[  107.100825] sd 7:0:0:0: [sdd] Assuming drive cache: write through
[  107.103842] sd 7:0:0:0: [sdd] No Caching mode page found
[  107.103852] sd 7:0:0:0: [sdd] Assuming drive cache: write through
[  107.120549]  sdd: sdd1
[  107.123283] sd 7:0:0:0: [sdd] No Caching mode page found
[  107.123292] sd 7:0:0:0: [sdd] Assuming drive cache: write through
[  107.123299] sd 7:0:0:0: [sdd] Attached SCSI removable disk
[  107.766056] FAT-fs (sdd1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[  107.864718] systemd-hostnamed[2722]: Warning: nss-myhostname is not installed. Changing the local hostname might make it unresolveable. Please install nss-myhostname!
[  135.259157] sdd: detected capacity change from 32027705344 to 0
[  140.361135] usb 8-1: USB disconnect, device number 3

Je n'ai mis que la fin du long processus, si vous voulez la transmission complète je peux vous la transmettre.

De plus en plus déconcertant pour moi...

@+ Elsimate

J5012 · Le 23/02/2015, à 01:47

seul un fsck effectif peut detecter et reparer la fat32 ... celle-ci est depourvue de tout mecanisme de verification de l'integrite des donnees ...

Bougron · Le 23/02/2015, à 14:10

Elsimate a écrit :

Bonjour, les choses se compliquent...j'ai dû faire de nombreux essais afin de bien cerner la manipulation qui entraîne le message d'erreur.
Première précision, j'ai accès aux données de mes clés USB en tout temps et aucune données n'est corrompues.
Ce que je dois faire pour que le message d'erreur s'affiche:
Démarrer mon système avec une clé insérer sur un port USB (USB3.0 dans ce cas), une fois en marche j'insère une autre clé USB dans l'autre port USB3.0, la clé est montée et j'ai accès au fichiers, si à ce stage je lance un " dmesg" au terminal, rien d'anormal.
J'éjecte la clé par un clique droit sur l'icône de celle-ci au lanceur, le message d'éjection me confirme que tout s'est bien dérouler, j'enlève la clé, je lance un second "dmesg" et voila, le message d'erreur est apparu :
[  107.099895] sd 7:0:0:0: [sdd] Write Protect is off
[  107.099904] sd 7:0:0:0: [sdd] Mode Sense: 23 00 00 00
[  107.100817] sd 7:0:0:0: [sdd] No Caching mode page found
[  107.100825] sd 7:0:0:0: [sdd] Assuming drive cache: write through
[  107.103842] sd 7:0:0:0: [sdd] No Caching mode page found
[  107.103852] sd 7:0:0:0: [sdd] Assuming drive cache: write through
[  107.120549]  sdd: sdd1
[  107.123283] sd 7:0:0:0: [sdd] No Caching mode page found
[  107.123292] sd 7:0:0:0: [sdd] Assuming drive cache: write through
[  107.123299] sd 7:0:0:0: [sdd] Attached SCSI removable disk
[  107.766056] FAT-fs (sdd1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[  107.864718] systemd-hostnamed[2722]: Warning: nss-myhostname is not installed. Changing the local hostname might make it unresolveable. Please install nss-myhostname!
[  135.259157] sdd: detected capacity change from 32027705344 to 0
[  140.361135] usb 8-1: USB disconnect, device number 3
Je n'ai mis que la fin du long processus, si vous voulez la transmission complète je peux vous la transmettre.
De plus en plus déconcertant pour moi...
@+ Elsimate

Très très étrange ce que tu dis.... J'invite ceux qui suivent cette discussion à faire l'essai suivant:
1) Monter une clé USB...
2) La démonter normalement par la commande appropriée "retirer le disque parent en toute sécurité".
3) Faire la commande "dmesg | tail -20"
On va certainement constater un sacré problème..... Tu n'es pas le seul..... Je suis aussi dans le lot sans le savoir et avec une seule clé USB ayant 3 partitions et montée sur un support USB2

[ 1646.479728] usb 1-1.2: new high-speed USB device number 15 using ehci-pci
[ 1646.594678] usb 1-1.2: New USB device found, idVendor=0951, idProduct=1666
[ 1646.594685] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1646.594689] usb 1-1.2: Product: DataTraveler 3.0
[ 1646.594692] usb 1-1.2: Manufacturer: Kingston
[ 1646.594695] usb 1-1.2: SerialNumber: 60A44C426697FE50C98100E8
[ 1646.595673] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 1646.596037] scsi14 : usb-storage 1-1.2:1.0
[ 1647.651684] scsi 14:0:0:0: Direct-Access     Kingston DataTraveler 3.0 1.00 PQ: 0 ANSI: 6
[ 1647.652594] sd 14:0:0:0: Attached scsi generic sg2 type 0
[ 1647.653592] sd 14:0:0:0: [sdb] 120845300 512-byte logical blocks: (61.8 GB/57.6 GiB)
[ 1647.654533] sd 14:0:0:0: [sdb] Write Protect is off
[ 1647.654540] sd 14:0:0:0: [sdb] Mode Sense: 4f 00 00 00
[ 1647.656012] sd 14:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1647.678495]  sdb: sdb1 sdb2 sdb3
[ 1647.682168] sd 14:0:0:0: [sdb] Attached SCSI removable disk
[ 1648.291318] FAT-fs (sdb1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 1648.334536] EXT4-fs (sdb2): mounted filesystem with ordered data mode. Opts: (null)
[ 1663.408308] usb 1-1.2: USB disconnect, device number 15
bougron@S70t-A:/var/log$

Dernière modification par Bougron (Le 23/02/2015, à 14:12)

Babdu89 · Le 23/02/2015, à 16:15

Bonjour.

Le test chez moi.
Hybryde 14.04, basée sur Ubuntu 14.04. kernel 3.13.0-45

Une clé usb3 deux partitions.
Verbatim STORE N GO 64 Go.
Machine en marche.
Branchement de la clé sur un port usb2 (les seuls dispo).
Montage de la clé. (ouverture dans Nautilus)
Éjection de la clé (dans Nautilus " Éjecter").
Clé toujours branchée

bernard@bernard-System-Product-Name:~$ dmesg | tail -20
[ 5339.377297] systemd-hostnamed[4367]: Warning: nss-myhostname is not installed. Changing the local hostname might make it unresolveable. Please install nss-myhostname!
[ 9140.749477] systemd-hostnamed[4670]: Warning: nss-myhostname is not installed. Changing the local hostname might make it unresolveable. Please install nss-myhostname!
[ 9144.536227] usb 1-1: new high-speed USB device number 2 using ehci-pci
[ 9144.671463] usb 1-1: New USB device found, idVendor=18a5, idProduct=0247
[ 9144.671473] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 9144.671477] usb 1-1: Product: STORE N GO
[ 9144.671480] usb 1-1: Manufacturer: Verbatim
[ 9144.671484] usb 1-1: SerialNumber: 1228201308010151
[ 9144.986082] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 9144.989190] scsi2 : usb-storage 1-1:1.0
[ 9144.989367] usbcore: registered new interface driver usb-storage
[ 9146.932712] scsi 2:0:0:0: Direct-Access     Verbatim STORE N GO       1100 PQ: 0 ANSI: 6
[ 9146.935204] sd 2:0:0:0: Attached scsi generic sg3 type 0
[ 9146.937604] sd 2:0:0:0: [sdb] 126025728 512-byte logical blocks: (64.5 GB/60.0 GiB)
[ 9146.938403] sd 2:0:0:0: [sdb] Write Protect is off
[ 9146.938411] sd 2:0:0:0: [sdb] Mode Sense: 22 00 00 00
[ 9146.953559] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 9146.961908]  sdb: sdb1 sdb2
[ 9146.975294] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 9164.099325] sdb: detected capacity change from 64525172736 to 0
bernard@bernard-System-Product-Name:~$

Clé débranchée;

bernard@bernard-System-Product-Name:~$ dmesg | tail -20
[ 9140.749477] systemd-hostnamed[4670]: Warning: nss-myhostname is not installed. Changing the local hostname might make it unresolveable. Please install nss-myhostname!
[ 9144.536227] usb 1-1: new high-speed USB device number 2 using ehci-pci
[ 9144.671463] usb 1-1: New USB device found, idVendor=18a5, idProduct=0247
[ 9144.671473] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 9144.671477] usb 1-1: Product: STORE N GO
[ 9144.671480] usb 1-1: Manufacturer: Verbatim
[ 9144.671484] usb 1-1: SerialNumber: 1228201308010151
[ 9144.986082] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 9144.989190] scsi2 : usb-storage 1-1:1.0
[ 9144.989367] usbcore: registered new interface driver usb-storage
[ 9146.932712] scsi 2:0:0:0: Direct-Access     Verbatim STORE N GO       1100 PQ: 0 ANSI: 6
[ 9146.935204] sd 2:0:0:0: Attached scsi generic sg3 type 0
[ 9146.937604] sd 2:0:0:0: [sdb] 126025728 512-byte logical blocks: (64.5 GB/60.0 GiB)
[ 9146.938403] sd 2:0:0:0: [sdb] Write Protect is off
[ 9146.938411] sd 2:0:0:0: [sdb] Mode Sense: 22 00 00 00
[ 9146.953559] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 9146.961908]  sdb: sdb1 sdb2
[ 9146.975294] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 9164.099325] sdb: detected capacity change from 64525172736 to 0
[ 9317.976593] usb 1-1: USB disconnect, device number 2
bernard@bernard-System-Product-Name:~$

Je passe sur Unity, et je regarde ce que çà fait en rebranchant la clé.

Si çà peut aider.

@+. Babdu89 .

Babdu89 · Le 23/02/2015, à 16:33

Post#10, on peut lire...

J'ai aussi les deux choix, "retirer du lanceur" et "éjecter" je dois sélectionner ce "Éjecter" pour démonter la clé, si je sélectionne "Retirer du lanceur" la clé et son contenu sont encore visible dans "Fichiers".

Normal que les dossiers soient toujours accessibles.
Ce n'est pas la clé qui est "Retirer du lanceur", mais l'icône représentant le périphérique, la clé.
Tant que la clé ne sera pas "Éjectée" correctement, on à cette situation .
Si on "arrache" la clé en "bourrin", elle risque de ne pas trop aimer, surtout si elle est en état d'écriture...

Édit.
en utilisant "Éjecter" çà fonctionne normalement plusieurs fois de suites, pas de soucis.

@+. Babdu89 .

Dernière modification par Babdu89 (Le 23/02/2015, à 16:37)

Bougron · Le 23/02/2015, à 16:56

Pour la réparation FSCK, Ce n'est pas évident.

[ 49.652934] sdb: sdb1 sdb2 sdb3
[ 49.656565] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[ 50.292283] FAT-fs (sdb1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 50.331786] EXT4-fs (sdb2): recovery complete
[ 50.340238] EXT4-fs (sdb2): mounted filesystem with ordered data mode. Opts: (null)

$ sudo fsck /dev/sdb1
fsck de util-linux 2.20.1
fsck.fat 3.0.26 (2014-03-07)
0x41: Dirty bit is set. Fs was not properly unmounted and some data may be corrupt.
1) Remove dirty bit
2) No action
? 1
Leaving filesystem unchanged.
/dev/sdb1: 594 files, 5329/1048063 clusters

$ sudo fsck /dev/sdb1
fsck de util-linux 2.20.1
fsck.fat 3.0.26 (2014-03-07)
0x41: Dirty bit is set. Fs was not properly unmounted and some data may be corrupt.
1) Remove dirty bit
2) No action
? 2
There are differences between boot sector and its backup.
This is mostly harmless. Differences: (offset:original/backup)
65:01/00
1) Copy original to backup
2) Copy backup to original
3) No action
?

AJOUT; J'ai pris la décision de supprimer la partition et de la recréer. => problème solutionné.

Dernière modification par Bougron (Le 23/02/2015, à 19:54)

Elsimate · Le 23/02/2015, à 18:36

Bubdu89 a écrit :

Post#10, on peut lire...
J'ai aussi les deux choix, "retirer du lanceur" et "éjecter" je dois sélectionner ce "Éjecter" pour démonter la clé, si je sélectionne "Retirer du lanceur" la clé et son contenu sont encore visible dans "Fichiers".
Normal que les dossiers soient toujours accessibles.
Ce n'est pas la clé qui est "Retirer du lanceur", mais l'icône représentant le périphérique, la clé.
Tant que la clé ne sera pas "Éjectée" correctement, on à cette situation .

Je sais, je ne faisait que répondre à J5012 au #9

Rien n'a changé depuis mon dernier post concernant les ports USB, les choses s’aggravent même encore plus, comme présentement, mon imprimante branchée sur un port USB n'a pas démarrer, et quand elle démarre elle s'éteint parfois après quelque temps sans raison...

Aussi je n'ai plus revu l'option "Retirer en toute sécurité" des clés insérer que j’énumérais au #10... seul "Éjecter" apparaît.

J'ai démarrer mon système avec une clé insérer dans un port USB3.0 (Lexar/Multisystème) et une autre dans un port USB2.0 (Lexar aussi), j'ai insérer, lu le contenu et éjecter une clé Verbatin de 32G sur chacun des ports libres. Voici le contenu complet de "gmesg" avec les deux clés initialement insérer encore présente :

r 9
[    0.913022] usb usb9: New USB device found, idVendor=1d6b, idProduct=0003
[    0.913024] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.913025] usb usb9: Product: xHCI Host Controller
[    0.913026] usb usb9: Manufacturer: Linux 3.13.0-45-generic xhci_hcd
[    0.913027] usb usb9: SerialNumber: 0000:00:10.1
[    0.913127] hub 9-0:1.0: USB hub found
[    0.913133] hub 9-0:1.0: 2 ports detected
[    0.921303] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[    0.921306] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[    0.921488] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.921623] mousedev: PS/2 mouse device common for all mice
[    0.921745] rtc_cmos 00:07: RTC can wake from S4
[    0.921842] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
[    0.921863] rtc_cmos 00:07: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[    0.921922] device-mapper: uevent: version 1.0.3
[    0.921999] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com
[    0.922005] ledtrig-cpu: registered to indicate activity on CPUs
[    0.922007] EFI Variables Facility v0.08 2004-May-17
[    0.928864] TCP: cubic registered
[    0.928933] NET: Registered protocol family 10
[    0.929085] NET: Registered protocol family 17
[    0.929093] Key type dns_resolver registered
[    0.929469] Loading compiled-in X.509 certificates
[    0.930178] Loaded X.509 cert 'Magrathea: Glacier signing key: 34992139f3da40b620bd5517597ba85af5797c9a'
[    0.930188] registered taskstats version 1
[    0.932376] Key type trusted registered
[    0.933867] Key type encrypted registered
[    0.935389] AppArmor: AppArmor sha1 policy hashing enabled
[    0.935393] IMA: No TPM chip found, activating TPM-bypass!
[    0.935660] regulator-dummy: disabling
[    0.935741]   Magic number: 3:206:983
[    0.935775] acpi PNP0C14:00: hash matches
[    0.935821] rtc_cmos 00:07: setting system clock to 2015-02-23 10:57:50 UTC (1424689070)
[    0.935945] acpi-cpufreq: overriding BIOS provided _PSD data
[    0.936111] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    0.936112] EDD information not available.
[    0.936150] PM: Hibernation image not present or could not be loaded.
[    0.937296] Freeing unused kernel memory: 1336K (ffffffff81d20000 - ffffffff81e6e000)
[    0.937298] Write protecting the kernel read-only data: 12288k
[    0.939784] Freeing unused kernel memory: 796K (ffff880001739000 - ffff880001800000)
[    0.941952] Freeing unused kernel memory: 688K (ffff880001b54000 - ffff880001c00000)
[    0.950196] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2
[    0.954457] systemd-udevd[117]: starting version 204
[    0.968377] wmi: Mapper loaded
[    0.970500] ahci 0000:00:11.0: version 3.0
[    0.970716] ahci 0000:00:11.0: irq 54 for MSI/MSI-X
[    0.970721] ahci 0000:00:11.0: irq 55 for MSI/MSI-X
[    0.970726] ahci 0000:00:11.0: irq 56 for MSI/MSI-X
[    0.970730] ahci 0000:00:11.0: irq 57 for MSI/MSI-X
[    0.970735] ahci 0000:00:11.0: irq 58 for MSI/MSI-X
[    0.970740] ahci 0000:00:11.0: irq 59 for MSI/MSI-X
[    0.970744] ahci 0000:00:11.0: irq 60 for MSI/MSI-X
[    0.970749] ahci 0000:00:11.0: irq 61 for MSI/MSI-X
[    0.970815] ahci 0000:00:11.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x11 impl SATA mode
[    0.970818] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part 
[    0.973661] scsi0 : ahci
[    0.973738] scsi1 : ahci
[    0.973799] scsi2 : ahci
[    0.973856] scsi3 : ahci
[    0.973909] scsi4 : ahci
[    0.973946] ata1: SATA max UDMA/133 abar m2048@0xfeb51000 port 0xfeb51100 irq 54
[    0.973947] ata2: DUMMY
[    0.973949] ata3: DUMMY
[    0.973950] ata4: DUMMY
[    0.973952] ata5: SATA max UDMA/133 abar m2048@0xfeb51000 port 0xfeb51300 irq 58
[    0.974040] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    0.974272] r8169 0000:01:00.0: irq 62 for MSI/MSI-X
[    0.974421] r8169 0000:01:00.0 eth0: RTL8168f/8111f at 0xffffc90000d4a000, 54:be:f7:25:a0:af, XID 08100800 IRQ 62
[    0.974423] r8169 0000:01:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[    1.017149] usb 1-1: new high-speed USB device number 2 using ehci-pci
[    1.156288] usb 1-1: New USB device found, idVendor=04a9, idProduct=2774
[    1.156293] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    1.156295] usb 1-1: Product: MF4700 Series
[    1.156296] usb 1-1: Manufacturer: Canon Inc
[    1.156297] usb 1-1: SerialNumber: 0147824E4C26
[    1.268837] usb 1-2: new high-speed USB device number 3 using ehci-pci
[    1.407708] usb 1-2: New USB device found, idVendor=03f0, idProduct=1424
[    1.407711] usb 1-2: New USB device strings: Mfr=10, Product=11, SerialNumber=0
[    1.407713] usb 1-2: Product: f2105 2PORT USB 2.0 HUB
[    1.407715] usb 1-2: Manufacturer: HP\xffffffc3\xffffffbf\xffffffbf
[    1.408203] hub 1-2:1.0: USB hub found
[    1.408703] hub 1-2:1.0: 2 ports detected
[    1.464631] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    1.464661] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.465423] ata1.00: ATA-8: ST1000DM003-1CH162, CC44, max UDMA/133
[    1.465426] ata1.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    1.466161] ata1.00: configured for UDMA/133
[    1.466309] scsi 0:0:0:0: Direct-Access     ATA      ST1000DM003-1CH1 CC44 PQ: 0 ANSI: 5
[    1.466458] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.466466] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[    1.466468] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    1.466540] sd 0:0:0:0: [sda] Write Protect is off
[    1.466545] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.466585] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.478350] ata5.00: ATAPI: MATSHITA DVD-RAM SW830, 1.00, max UDMA/100
[    1.496787] ata5.00: configured for UDMA/100
[    1.503090] scsi 4:0:0:0: CD-ROM            MATSHITA DVD-RAM SW830    1.00 PQ: 0 ANSI: 5
[    1.512148] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[    1.512152] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.512291] sr 4:0:0:0: Attached scsi CD-ROM sr0
[    1.512352] sr 4:0:0:0: Attached scsi generic sg1 type 5
[    1.516942]  sda: sda1 sda2 sda3 sda4 sda5 sda6 sda7 sda8 sda9
[    1.517518] sd 0:0:0:0: [sda] Attached SCSI disk
[    1.660418] tsc: Refined TSC clocksource calibration: 3693.098 MHz
[    1.836199] usb 2-1: new high-speed USB device number 2 using ehci-pci
[    1.969209] usb 2-1: New USB device found, idVendor=0bda, idProduct=0129
[    1.969213] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    1.969214] usb 2-1: Product: USB2.0-CRW
[    1.969216] usb 2-1: Manufacturer: Generic
[    1.969217] usb 2-1: SerialNumber: 20100201396000000
[    2.080102] usb 8-2: new high-speed USB device number 2 using xhci_hcd
[    2.373644] usb 8-2: New USB device found, idVendor=05dc, idProduct=a817
[    2.373648] usb 8-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    2.373649] usb 8-2: Product: JumpDrive
[    2.373651] usb 8-2: Manufacturer: Lexar
[    2.373652] usb 8-2: SerialNumber: AA4YMJ17LTNBAUCT
[    2.373766] usb 8-2: ep 0x81 - rounding interval to 128 microframes, ep desc says 255 microframes
[    2.373771] usb 8-2: ep 0x2 - rounding interval to 128 microframes, ep desc says 255 microframes
[    2.376758] usb-storage 8-2:1.0: USB Mass Storage device detected
[    2.376842] scsi5 : usb-storage 8-2:1.0
[    2.376891] usbcore: registered new interface driver usb-storage
[    2.659557] Switched to clocksource tsc
[    2.763341] usb 3-4: new low-speed USB device number 2 using ohci-pci
[    2.930278] usb 3-4: New USB device found, idVendor=046d, idProduct=c077
[    2.930282] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.930283] usb 3-4: Product: USB Optical Mouse
[    2.930285] usb 3-4: Manufacturer: Logitech
[    2.934773] hidraw: raw HID events driver (C) Jiri Kosina
[    2.940412] usbcore: registered new interface driver usbhid
[    2.940415] usbhid: USB HID core driver
[    2.941714] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:12.0/usb3/3-4/3-4:1.0/input/input3
[    2.941826] hid-generic 0003:046D:C077.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:12.0-4/input0
[    3.194911] usb 3-5: new full-speed USB device number 3 using ohci-pci
[    3.367842] usb 3-5: string descriptor 0 read error: -22
[    3.367848] usb 3-5: New USB device found, idVendor=04ca, idProduct=3006
[    3.367850] usb 3-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    3.443047] usb 1-2.1: new high-speed USB device number 6 using ehci-pci
[    3.536691] usb 1-2.1: New USB device found, idVendor=05dc, idProduct=0700
[    3.536695] usb 1-2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    3.536696] usb 1-2.1: Product: JumpDrive
[    3.536698] usb 1-2.1: Manufacturer: Lexar
[    3.536699] usb 1-2.1: SerialNumber: 2271188422
[    3.536890] usb-storage 1-2.1:1.0: USB Mass Storage device detected
[    3.536964] scsi6 : usb-storage 1-2.1:1.0
[    3.755807] EXT4-fs (sda7): mounted filesystem with ordered data mode. Opts: (null)
[    3.776404] scsi 5:0:0:0: Direct-Access     Lexar    JumpDrive        1100 PQ: 0 ANSI: 0 CCS
[    3.776641] sd 5:0:0:0: Attached scsi generic sg2 type 0
[    3.776907] sd 5:0:0:0: [sdb] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
[    3.777738] sd 5:0:0:0: [sdb] Write Protect is off
[    3.777742] sd 5:0:0:0: [sdb] Mode Sense: 43 00 00 00
[    3.778532] sd 5:0:0:0: [sdb] No Caching mode page found
[    3.778536] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[    3.781093] sd 5:0:0:0: [sdb] No Caching mode page found
[    3.781097] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[    3.782194]  sdb: sdb1
[    3.784552] sd 5:0:0:0: [sdb] No Caching mode page found
[    3.784557] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[    3.784560] sd 5:0:0:0: [sdb] Attached SCSI removable disk
[    3.811367] random: nonblocking pool is initialized
[    4.534252] scsi 6:0:0:0: Direct-Access     Lexar    JumpDrive        1.00 PQ: 0 ANSI: 6
[    4.534421] sd 6:0:0:0: Attached scsi generic sg3 type 0
[    4.534992] sd 6:0:0:0: [sdc] 62545920 512-byte logical blocks: (32.0 GB/29.8 GiB)
[    4.535375] sd 6:0:0:0: [sdc] Write Protect is off
[    4.535380] sd 6:0:0:0: [sdc] Mode Sense: 23 00 00 00
[    4.535744] sd 6:0:0:0: [sdc] Write cache: disabled, read cache: disabled, doesn't support DPO or FUA
[    4.538844]  sdc: sdc1
[    4.540756] sd 6:0:0:0: [sdc] Attached SCSI removable disk
[   10.301092] Adding 8191996k swap on /dev/sda8.  Priority:-1 extents:1 across:8191996k FS
[   10.375242] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   10.417460] systemd-udevd[340]: starting version 204
[   10.525819] lp: driver loaded but no devices found
[   10.531372] ppdev: user-space parallel port driver
[   10.539625] AMD IOMMUv2 driver by Joerg Roedel <joerg.roedel@amd.com>
[   10.545857] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[   10.545862] Disabling lock debugging due to kernel taint
[   10.553471] fglrx: module verification failed: signature and/or  required key missing - tainting kernel
[   10.561427] <6>[fglrx] Maximum main memory to use for locked dma buffers: 6880 MBytes.
[   10.561516] <6>[fglrx]   vendor: 1002 device: 990c count: 1
[   10.561802] <6>[fglrx] IOMMU is enabled, CrossFire are not supported on this platform
[   10.561804] <6>[fglrx] Disable IOMMU in BIOS options or kernel boot parameters to support CF
[   10.561887] <6>[fglrx] ioport: bar 1, base 0xf000, size: 0x100
[   10.562384] <6>[fglrx] Kernel PAT support is enabled
[   10.562405] <6>[fglrx] module loaded - fglrx 13.35.5 [Mar 12 2014] with 1 minors
[   10.562565] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   10.580746] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[   10.580798] piix4_smbus 0000:00:14.0: Auxiliary SMBus Host Controller at 0xb20
[   10.601041] snd_hda_intel 0000:00:01.1: enabling device (0000 -> 0002)
[   10.601127] cfg80211: Calling CRDA to update world regulatory domain
[   10.601232] hda-intel 0000:00:01.1: Using LPIB position fix
[   10.601234] hda-intel 0000:00:01.1: Force to non-snoop mode
[   10.601270] snd_hda_intel 0000:00:01.1: irq 63 for MSI/MSI-X
[   10.603588] hda-intel 0000:00:01.1: Enable sync_write for stable communication
[   10.607280] Bluetooth: Core ver 2.17
[   10.607300] NET: Registered protocol family 31
[   10.607301] Bluetooth: HCI device and connection manager initialized
[   10.607310] Bluetooth: HCI socket layer initialized
[   10.607312] Bluetooth: L2CAP socket layer initialized
[   10.607315] Bluetooth: SCO socket layer initialized
[   10.610115] usbcore: registered new interface driver btusb
[   10.611113] usbcore: registered new interface driver ath3k
[   10.612922] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.1/sound/card0/input4
[   10.615906] hda-intel 0000:00:14.2: Using LPIB position fix
[   10.621258] hda-intel 0000:00:14.2: Enable sync_write for stable communication
[   10.629493] hda_codec: ALC662 rev3: SKU not ready 0x411111f0
[   10.629703] autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:line
[   10.629705]    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   10.629706]    hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[   10.629707]    mono: mono_out=0x0
[   10.629708]    inputs:
[   10.629710]      Front Mic=0x19
[   10.629712]      Rear Mic=0x18
[   10.629713]      Line=0x1a
[   10.629714] realtek: No valid SSID, checking pincfg 0x411111f0 for NID 0x1d
[   10.629715] realtek: Enable default setup for auto mode as fallback
[   10.633037] ath9k 0000:04:00.0: enabling device (0000 -> 0002)
[   10.640126] input: HD-Audio Generic Front Headphone as /devices/pci0000:00/0000:00:14.2/sound/card1/input9
[   10.640194] input: HD-Audio Generic Line Out as /devices/pci0000:00/0000:00:14.2/sound/card1/input8
[   10.641200] type=1400 audit(1424707080.210:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/sbin/dhclient" pid=453 comm="apparmor_parser"
[   10.641205] type=1400 audit(1424707080.210:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=453 comm="apparmor_parser"
[   10.641209] type=1400 audit(1424707080.210:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=453 comm="apparmor_parser"
[   10.641502] type=1400 audit(1424707080.210:5): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=453 comm="apparmor_parser"
[   10.641506] type=1400 audit(1424707080.210:6): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=453 comm="apparmor_parser"
[   10.641657] type=1400 audit(1424707080.210:7): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=453 comm="apparmor_parser"
[   10.641859] input: HD-Audio Generic Line as /devices/pci0000:00/0000:00:14.2/sound/card1/input7
[   10.641910] input: HD-Audio Generic Rear Mic as /devices/pci0000:00/0000:00:14.2/sound/card1/input6
[   10.641960] input: HD-Audio Generic Front Mic as /devices/pci0000:00/0000:00:14.2/sound/card1/input5
[   10.642329] ath: phy0: ASPM enabled: 0x43
[   10.642333] ath: EEPROM regdomain: 0x6a
[   10.642335] ath: EEPROM indicates we should expect a direct regpair map
[   10.642337] ath: Country alpha2 being used: 00
[   10.642338] ath: Regpair used: 0x6a
[   10.652264] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   10.652607] ieee80211 phy0: Atheros AR9462 Rev:2 mem=0xffffc90011b00000, irq=18
[   10.674321] WARNING! power/level is deprecated; use power/control instead
[   10.675457] kvm: Nested Virtualization enabled
[   10.675461] kvm: Nested Paging enabled
[   10.707360] type=1400 audit(1424707080.274:8): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/sbin/dhclient" pid=504 comm="apparmor_parser"
[   10.707367] type=1400 audit(1424707080.274:9): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=504 comm="apparmor_parser"
[   10.707370] type=1400 audit(1424707080.274:10): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=504 comm="apparmor_parser"
[   10.707744] type=1400 audit(1424707080.278:11): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=504 comm="apparmor_parser"
[   10.793081] cfg80211: World regulatory domain updated:
[   10.793085] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   10.793086] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.793088] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.793089] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   10.793090] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.793091] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.887062] rts5139: module is from the staging directory, the quality is unknown, you have been warned.
[   10.895366] scsi7 : SCSI emulation for RTS5139 USB card reader
[   10.895552] scsi 7:0:0:0: Direct-Access     Generic- xD/SD/M.S.       1.00 PQ: 0 ANSI: 0 CCS
[   10.895905] sd 7:0:0:0: Attached scsi generic sg4 type 0
[   10.897436] usbcore: registered new interface driver rts5139
[   10.999754] sd 7:0:0:0: [sdd] Attached SCSI removable disk
[   12.545588] usblp 1-1:1.1: usblp1: USB Bidirectional printer dev 2 if 1 alt 0 proto 2 vid 0x04A9 pid 0x2774
[   12.547544] usblp 1-1:1.2: usblp2: USB Bidirectional printer dev 2 if 2 alt 0 proto 2 vid 0x04A9 pid 0x2774
[   12.547580] usbcore: registered new interface driver usblp
[   13.484968] EXT4-fs (sda7): re-mounted. Opts: errors=remount-ro
[   13.754852] EXT4-fs (sda9): mounted filesystem with ordered data mode. Opts: (null)
[   16.048899] init: failsafe main process (881) killed by TERM signal
[   16.109700] init: Failed to spawn ofono main process: unable to execute: No such file or directory
[   16.211994] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   16.211999] Bluetooth: BNEP filters: protocol multicast
[   16.212008] Bluetooth: BNEP socket layer initialized
[   16.218041] Bluetooth: RFCOMM TTY layer initialized
[   16.218052] Bluetooth: RFCOMM socket layer initialized
[   16.218058] Bluetooth: RFCOMM ver 1.11
[   16.239978] audit_printk_skb: 6 callbacks suppressed
[   16.239985] type=1400 audit(1424707085.814:14): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/cups/backend/cups-pdf" pid=1024 comm="apparmor_parser"
[   16.239991] type=1400 audit(1424707085.814:15): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/cupsd" pid=1024 comm="apparmor_parser"
[   16.240315] type=1400 audit(1424707085.814:16): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=1024 comm="apparmor_parser"
[   16.360964] type=1400 audit(1424707085.934:17): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/sbin/dhclient" pid=1080 comm="apparmor_parser"
[   16.360973] type=1400 audit(1424707085.934:18): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1080 comm="apparmor_parser"
[   16.360978] type=1400 audit(1424707085.934:19): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=1080 comm="apparmor_parser"
[   16.361012] type=1400 audit(1424707085.934:20): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/lightdm/lightdm-guest-session" pid=1079 comm="apparmor_parser"
[   16.361019] type=1400 audit(1424707085.934:21): apparmor="STATUS" operation="profile_load" profile="unconfined" name="chromium" pid=1079 comm="apparmor_parser"
[   16.361220] type=1400 audit(1424707085.934:22): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="chromium" pid=1079 comm="apparmor_parser"
[   16.361320] type=1400 audit(1424707085.934:23): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1080 comm="apparmor_parser"
[   16.509572] init: cups main process (1061) killed by HUP signal
[   16.509582] init: cups main process ended, respawning
[   16.919712] Non-volatile memory driver v1.3
[   17.367695] r8169 0000:01:00.0 eth0: link down
[   17.367754] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   17.368055] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   17.396817] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   17.400015] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   18.738599] fglrx_pci 0000:00:01.0: irq 64 for MSI/MSI-X
[   18.739394] <6>[fglrx] Firegl kernel thread PID: 1449
[   18.739557] <6>[fglrx] Firegl kernel thread PID: 1450
[   18.739659] <6>[fglrx] Firegl kernel thread PID: 1451
[   18.739763] <6>[fglrx] IRQ 64 Enabled
[   18.743249] <6>[fglrx] Reserved FB block: Shared offset:0, size:1000000 
[   18.743251] <6>[fglrx] Reserved FB block: Unshared offset:fb78000, size:4000 
[   18.743252] <6>[fglrx] Reserved FB block: Unshared offset:fb7c000, size:484000 
[   18.743253] <6>[fglrx] Reserved FB block: Unshared offset:2ffee000, size:12000 
[   18.959346] r8169 0000:01:00.0 eth0: link up
[   18.959355] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   19.268150] init: plymouth-upstart-bridge main process ended, respawning
[   19.273296] init: plymouth-upstart-bridge main process (1459) terminated with status 1
[   19.273308] init: plymouth-upstart-bridge main process ended, respawning
[   24.873579] FAT-fs (sdb1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[   46.379091] audit_printk_skb: 132 callbacks suppressed
[   46.379095] type=1400 audit(1424707115.973:68): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/lib/cups/backend/cups-pdf" pid=2338 comm="apparmor_parser"
[   46.379100] type=1400 audit(1424707115.973:69): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=2338 comm="apparmor_parser"
[   46.379433] type=1400 audit(1424707115.973:70): apparmor="STATUS" operation="profile_replace" profile="unconfined" name="/usr/sbin/cupsd" pid=2338 comm="apparmor_parser"
[  145.888939] usb 1-2.2: new high-speed USB device number 7 using ehci-pci
[  145.988951] usb 1-2.2: New USB device found, idVendor=13fe, idProduct=3600
[  145.988958] usb 1-2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  145.988962] usb 1-2.2: Product: STORE N GO
[  145.988966] usb 1-2.2: Manufacturer: Verbatim
[  145.988969] usb 1-2.2: SerialNumber: 07B81902542E0141
[  145.989304] usb-storage 1-2.2:1.0: USB Mass Storage device detected
[  145.989368] usb-storage 1-2.2:1.0: Quirks match for vid 13fe pid 3600: 4000
[  145.989403] scsi8 : usb-storage 1-2.2:1.0
[  147.010949] scsi 8:0:0:0: Direct-Access     Verbatim STORE N GO       PMAP PQ: 0 ANSI: 0 CCS
[  147.011412] sd 8:0:0:0: Attached scsi generic sg5 type 0
[  147.451319] sd 8:0:0:0: [sde] 62554112 512-byte logical blocks: (32.0 GB/29.8 GiB)
[  147.452565] sd 8:0:0:0: [sde] Write Protect is off
[  147.452574] sd 8:0:0:0: [sde] Mode Sense: 23 00 00 00
[  147.453811] sd 8:0:0:0: [sde] No Caching mode page found
[  147.453819] sd 8:0:0:0: [sde] Assuming drive cache: write through
[  147.458437] sd 8:0:0:0: [sde] No Caching mode page found
[  147.458445] sd 8:0:0:0: [sde] Assuming drive cache: write through
[  147.475013]  sde: sde1
[  147.479858] sd 8:0:0:0: [sde] No Caching mode page found
[  147.479866] sd 8:0:0:0: [sde] Assuming drive cache: write through
[  147.479872] sd 8:0:0:0: [sde] Attached SCSI removable disk
[  148.132464] FAT-fs (sde1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[  148.248851] systemd-hostnamed[2426]: Warning: nss-myhostname is not installed. Changing the local hostname might make it unresolveable. Please install nss-myhostname!
[  159.531636] sde: detected capacity change from 32027705344 to 0
[  163.332298] usb 1-2.2: USB disconnect, device number 7
[  168.521675] usb 8-1: new high-speed USB device number 3 using xhci_hcd
[  168.543986] usb 8-1: New USB device found, idVendor=13fe, idProduct=3600
[  168.543993] usb 8-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  168.543997] usb 8-1: Product: STORE N GO
[  168.544000] usb 8-1: Manufacturer: Verbatim
[  168.544003] usb 8-1: SerialNumber: 07B81902542E0141
[  168.544887] usb-storage 8-1:1.0: USB Mass Storage device detected
[  168.544951] usb-storage 8-1:1.0: Quirks match for vid 13fe pid 3600: 4000
[  168.544993] scsi9 : usb-storage 8-1:1.0
[  169.564451] scsi 9:0:0:0: Direct-Access     Verbatim STORE N GO       PMAP PQ: 0 ANSI: 0 CCS
[  169.564958] sd 9:0:0:0: Attached scsi generic sg5 type 0
[  170.005573] sd 9:0:0:0: [sde] 62554112 512-byte logical blocks: (32.0 GB/29.8 GiB)
[  170.006430] sd 9:0:0:0: [sde] Write Protect is off
[  170.006440] sd 9:0:0:0: [sde] Mode Sense: 23 00 00 00
[  170.007244] sd 9:0:0:0: [sde] No Caching mode page found
[  170.007253] sd 9:0:0:0: [sde] Assuming drive cache: write through
[  170.010473] sd 9:0:0:0: [sde] No Caching mode page found
[  170.010480] sd 9:0:0:0: [sde] Assuming drive cache: write through
[  170.027138]  sde: sde1
[  170.029910] sd 9:0:0:0: [sde] No Caching mode page found
[  170.029919] sd 9:0:0:0: [sde] Assuming drive cache: write through
[  170.029925] sd 9:0:0:0: [sde] Attached SCSI removable disk
[  170.672527] FAT-fs (sde1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[  180.109985] sde: detected capacity change from 32027705344 to 0
[ 1185.715338] usb 8-1: USB disconnect, device number 3
[ 1192.776874] usb 1-2.2: new high-speed USB device number 8 using ehci-pci
[ 1192.872895] usb 1-2.2: New USB device found, idVendor=13fe, idProduct=3600
[ 1192.872903] usb 1-2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1192.872907] usb 1-2.2: Product: STORE N GO
[ 1192.872910] usb 1-2.2: Manufacturer: Verbatim
[ 1192.872913] usb 1-2.2: SerialNumber: 07B81902542E0141
[ 1192.874196] usb-storage 1-2.2:1.0: USB Mass Storage device detected
[ 1192.874277] usb-storage 1-2.2:1.0: Quirks match for vid 13fe pid 3600: 4000
[ 1192.874323] scsi10 : usb-storage 1-2.2:1.0
[ 1193.894527] scsi 10:0:0:0: Direct-Access     Verbatim STORE N GO       PMAP PQ: 0 ANSI: 0 CCS
[ 1193.894942] sd 10:0:0:0: Attached scsi generic sg5 type 0
[ 1194.340138] sd 10:0:0:0: [sde] 62554112 512-byte logical blocks: (32.0 GB/29.8 GiB)
[ 1194.341387] sd 10:0:0:0: [sde] Write Protect is off
[ 1194.341394] sd 10:0:0:0: [sde] Mode Sense: 23 00 00 00
[ 1194.342640] sd 10:0:0:0: [sde] No Caching mode page found
[ 1194.342647] sd 10:0:0:0: [sde] Assuming drive cache: write through
[ 1194.347491] sd 10:0:0:0: [sde] No Caching mode page found
[ 1194.347500] sd 10:0:0:0: [sde] Assuming drive cache: write through
[ 1194.364068]  sde: sde1
[ 1194.369042] sd 10:0:0:0: [sde] No Caching mode page found
[ 1194.369052] sd 10:0:0:0: [sde] Assuming drive cache: write through
[ 1194.369057] sd 10:0:0:0: [sde] Attached SCSI removable disk
[ 1195.021060] FAT-fs (sde1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 1195.103688] systemd-hostnamed[2790]: Warning: nss-myhostname is not installed. Changing the local hostname might make it unresolveable. Please install nss-myhostname!
[ 1209.781531] sde: detected capacity change from 32027705344 to 0
[ 1213.801527] usb 1-2.2: USB disconnect, device number 8
ubuntu@Aspire:~$

Si cela peut vous être utile.

Inutile de préciser que mes connaissances informatique sont très limités.

@+ Elsimate

Bougron · Le 23/02/2015, à 19:39

Bonsoir
Ce qui serait utile c'est de faire (voir mon post #22)

sudo fsck /dev/sdb1

sudo fsck /dev/sde1

afin de connaître la maladie.

PS: Comme il me semble que tu peux lire cette partition, tu devrais simplement sauver les données, la supprimer et la recréer.

Dernière modification par Bougron (Le 23/02/2015, à 19:57)

Elsimate · Le 23/02/2015, à 20:43

Bonjour Bougron.

Après avoir repris les manipulations de mon précédent post.

Retour de sudo fsck /dev/sdb1 (post #22)

ubuntu@Aspire:~$ sudo fsck /dev/sdb1
[sudo] password for ubuntu: 
fsck de util-linux 2.20.1
fsck.fat 3.0.26 (2014-03-07)
0x25: Dirty bit is set. Fs was not properly unmounted and some data may be corrupt.
1) Remove dirty bit
2) No action
? 1
Leaving filesystem unchanged.
/dev/sdb1: 164 files, 30907/62142 clusters

Même commande mais option 2 (post #22):

ubuntu@Aspire:~$ sudo fsck /dev/sdb1
[sudo] password for ubuntu: 
fsck de util-linux 2.20.1
fsck.fat 3.0.26 (2014-03-07)
0x25: Dirty bit is set. Fs was not properly unmounted and some data may be corrupt.
1) Remove dirty bit
2) No action
? 2
/dev/sdb1: 164 files, 30907/62142 clusters
ubuntu@Aspire:~$

@+ Elsimate

Edit : Ne tenez pas compte de mes commentaires au sujet de mon imprimante au post 23, tout semble normal, par souci d'économie elle tombe en veille si non utiliser après un certain temps. Je commence à fabuler...

Dernière modification par Elsimate (Le 23/02/2015, à 20:50)

Ubuntu-fr

Navigation

Liens de recherche

Annonce

#1 Le 13/02/2015, à 18:58

(Abandon) Ports USB non fonctionnel

#2 Le 13/02/2015, à 20:05

Re : (Abandon) Ports USB non fonctionnel

#3 Le 13/02/2015, à 20:43

Re : (Abandon) Ports USB non fonctionnel

#4 Le 14/02/2015, à 02:38

Re : (Abandon) Ports USB non fonctionnel

#5 Le 15/02/2015, à 21:19

Re : (Abandon) Ports USB non fonctionnel

#6 Le 15/02/2015, à 21:31

Re : (Abandon) Ports USB non fonctionnel

#7 Le 15/02/2015, à 21:49

Re : (Abandon) Ports USB non fonctionnel

#8 Le 17/02/2015, à 03:06

Re : (Abandon) Ports USB non fonctionnel

#9 Le 17/02/2015, à 04:35

Re : (Abandon) Ports USB non fonctionnel

#10 Le 17/02/2015, à 16:04

Re : (Abandon) Ports USB non fonctionnel

#11 Le 17/02/2015, à 22:42

Re : (Abandon) Ports USB non fonctionnel

#12 Le 17/02/2015, à 23:32

Re : (Abandon) Ports USB non fonctionnel

#13 Le 18/02/2015, à 00:19

Re : (Abandon) Ports USB non fonctionnel

#14 Le 18/02/2015, à 02:46

Re : (Abandon) Ports USB non fonctionnel

#15 Le 18/02/2015, à 22:45

Re : (Abandon) Ports USB non fonctionnel

#16 Le 19/02/2015, à 10:45

Re : (Abandon) Ports USB non fonctionnel

#17 Le 19/02/2015, à 16:37

Re : (Abandon) Ports USB non fonctionnel

#18 Le 23/02/2015, à 01:47

Re : (Abandon) Ports USB non fonctionnel

#19 Le 23/02/2015, à 14:10

Re : (Abandon) Ports USB non fonctionnel

#20 Le 23/02/2015, à 16:15

Re : (Abandon) Ports USB non fonctionnel

#21 Le 23/02/2015, à 16:33

Re : (Abandon) Ports USB non fonctionnel

#22 Le 23/02/2015, à 16:56

Re : (Abandon) Ports USB non fonctionnel

#23 Le 23/02/2015, à 18:36

Re : (Abandon) Ports USB non fonctionnel

#24 Le 23/02/2015, à 19:39

Re : (Abandon) Ports USB non fonctionnel

#25 Le 23/02/2015, à 20:43

Re : (Abandon) Ports USB non fonctionnel

Pied de page des forums