#26 Le 10/12/2019, à 18:27
- juliensl
Re : Installation Ubuntu 18.4.3
Quand je suis là :
https://doc.ubuntu-fr.org/lib/exe/fetch … 025783.png
Et que je clique sur "réparation recommandé", il commence, travail un peu, puis me dit : "Please close all your package managers (Software Center, Update Manager, Synaptic, ...). Then try again."
Idem, quand je suis ici :
https://doc.ubuntu-fr.org/lib/exe/fetch … 922587.png
Que j'appuie sur "Appliquer", il travail un peu, puis me dit : "Please close all your package managers (Software Center, Update Manager, Synaptic, ...). Then try again."
Je viens de faire
sudo ubiquity -b
L'installe se déroule, puie quand il arrive à "Copie des fichiers presque terminée..."
Il me dit :
"Le programme d'installation a rencontré une erreur lors de la copie des fichiers sur le disque dur :
[Errno 5] Input/output error
Ceci est souvent causé par un disque ou un lecteur CD/DVD défectueux ou un disque dur défectueux. Vous pouvez essayer de nettoyer le CD/DVD, de le graver à vitesse réduite ou de nettoyer la lentille du lecteur CD/DVD (des trousses de nettoyage sont souvent disponibles dans des magasins d'électronique). Il peut aussi être utile de vérifier l'âge du disque dur et d'envisager un éventuel remplacement, ou de déplacer votre système dans un environnement plus frais."
C'est ce que je disais dans le poste #1, je pense qu'il fait un "checksum" avant la fin et qu'il plante car j'ai du modifier le fichier grubx64.efi en mmx64.efi car sinon il ne voulait pas booter dessus.
Hors ligne
#27 Le 10/12/2019, à 18:38
- geole
Re : Installation Ubuntu 18.4.3
On va quand même s'assurer de quelque chose en regardant l'état du disque dur
Toujours avec ton support d'installation, tu installes le logiciel
sudo apt-get install --no-install-recommends smartmontools
et tu donnes le retour de cette commande
sudo smartctl -s on -a /dev/sda
sudo smartctl -s on -a /dev/sdb
Dernière modification par geole (Le 10/12/2019, à 18:41)
Les grilles de l'installateur https://doc.ubuntu-fr.org/tutoriel/inst … _subiquity
"gedit admin:///etc/fstab" est proscrit, utilisez "pkexec env DISPLAY=$DISPLAY XAUTHORITY=$XAUTHORITY xdg-open /etc/fstab" Voir https://doc.ubuntu-fr.org/gedit
Les partitions EXT4 des disques externes => https://forum.ubuntu-fr.org/viewtopic.p … #p22697248
Hors ligne
#28 Le 10/12/2019, à 18:49
- juliensl
Re : Installation Ubuntu 18.4.3
sudo smartctl -s on -a /dev/sda
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-5.0.0-23-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: ST2000LX001-1RG174
Serial Number: WDZ4FFHE
LU WWN Device Id: 5 000c50 0a95644c6
Firmware Version: SDM1
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-3 T13/2161-D revision 3b
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Tue Dec 10 17:48:16 2019 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x79) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 330) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 082 064 006 Pre-fail Always - 166479101
3 Spin_Up_Time 0x0003 099 099 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 096 096 020 Old_age Always - 4462
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 067 060 045 Pre-fail Always - 21499256273
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 1838 (54 19 0)
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 020 Old_age Always - 2044
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 098 000 Old_age Always - 13
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 067 057 040 Old_age Always - 33 (Min/Max 23/33)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 24
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 57
193 Load_Cycle_Count 0x0032 096 096 000 Old_age Always - 8392
194 Temperature_Celsius 0x0022 033 043 000 Old_age Always - 33
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 5906 (45 178 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 6971352582
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 9816379609
254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
sudo smartctl -s on -a /dev/sdb
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-5.0.0-23-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: Micron_1100_MTFDDAV256TBN
Serial Number: 171816F8CB1D
LU WWN Device Id: 5 00a075 116f8cb1d
Firmware Version: M0MA020
User Capacity: 256,060,514,304 bytes [256 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: < 1.8 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-3 T13/2161-D revision 5
SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Tue Dec 10 17:48:55 2019 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 678) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 4) minutes.
Conveyance self-test routine
recommended polling time: ( 3) minutes.
SCT capabilities: (0x0035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 000 Pre-fail Always - 0
5 Reallocated_Sector_Ct 0x0032 100 100 010 Old_age Always - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 667
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 2146
171 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
172 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
173 Unknown_Attribute 0x0032 098 098 000 Old_age Always - 39
174 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 191
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0032 100 100 000 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
194 Temperature_Celsius 0x0022 067 045 000 Old_age Always - 33 (Min/Max 10/55)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 100 100 000 Old_age Always - 0
202 Unknown_SSD_Attribute 0x0030 098 098 001 Old_age Offline - 2
206 Unknown_SSD_Attribute 0x000e 100 100 000 Old_age Always - 0
246 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 10097009572
247 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 316611173
248 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 115294005
180 Unused_Rsvd_Blk_Cnt_Tot 0x0033 000 000 000 Pre-fail Always - 2051
210 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Me dis pas qu'il est cassé... :'( :'( :'(
Hors ligne
#29 Le 10/12/2019, à 19:01
- geole
Re : Installation Ubuntu 18.4.3
On va dire que c'est le support d'installation qui a un problème.
Peux-tu en refaire un nouveau. Pour éviter le problème que tu as rencontré, télécharge la version 19.10 ( http://releases.ubuntu.com/eoan/ )
NOTA. Je considère que cette ligne
180 Unused_Rsvd_Blk_Cnt_Tot 0x0033 000 000 000 Pre-fail Always - 2051
est plus un bug du firmware qui ne sait pas gérer. ( https://www.google.com/search?q=%22Unus … 78&bih=643 )
Je n'ai trouvé dans le web, qu'une autre discussion avec le même modèle. ( https://forum.mxlinux.org/viewtopic.php?t=49081 )
Mais ton gros disque n'est pas excellant malgré son jeune âge. On aurait pu avoir mieux.
7 Seek_Error_Rate 0x000f 067 060 045 Pre-fail Always - 21499256273
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 1838 (54 19 0)
Dernière modification par geole (Le 10/12/2019, à 19:33)
Les grilles de l'installateur https://doc.ubuntu-fr.org/tutoriel/inst … _subiquity
"gedit admin:///etc/fstab" est proscrit, utilisez "pkexec env DISPLAY=$DISPLAY XAUTHORITY=$XAUTHORITY xdg-open /etc/fstab" Voir https://doc.ubuntu-fr.org/gedit
Les partitions EXT4 des disques externes => https://forum.ubuntu-fr.org/viewtopic.p … #p22697248
Hors ligne
#30 Le 11/12/2019, à 14:50
- juliensl
Re : Installation Ubuntu 18.4.3
Ah ben voilà ! ça a fonctionnait cette fois-ci !
Merci pour toute ton aide j'ai cru que je m'en sortirais jamais XD
Passes une bonne journée
Hors ligne
#31 Le 12/12/2019, à 16:11
- malbo
Re : Installation Ubuntu 18.4.3
@Doume86 : pour ouvrir une nouvelle discussion, tu trouveras des indications dans le paragraphe 4.1 Initier une nouvelle discussion de la doc "Aide à l'utilisation du forum Ubuntu‑FR".
Hors ligne