Ubuntu-fr

thcx

Re : Pinnacle PCTV USB Stick et ubuntu

Y a t-il l'icône digital TV dans la fenêtre de kaffeine ?

Avez vous placé le fichier de configuration des fréquences dans ~/.kde/share/apps/kaffeine/dvb-t/fr-Ville ?

Robinou

Re : Pinnacle PCTV USB Stick et ubuntu

Oui moi j'ai l'icône digital TV dans ma fenêtre kaffeine. D'ailleurs il me dit plus le message d'erreur quand je lance kaffeine...mais ça marche toujours pas! Au fait, j'suis pas exactement dans le cas de manolito, car j'ai une Pinnacle pctv usb stick.

Le problème c'est que quand je scanne les chaines, il n'en trouve aucune (que ce soit avec la petite antenne fournie avec la clé ou l'antenne extérieur de mon immeuble). Pourtant je suis dans une zone couverte par la tnt.

thcx, c'est quoi ton histoire de fichier de configuration des fréquences ?

thcx

Re : Pinnacle PCTV USB Stick et ubuntu

Il faut placer le fichier correspondant à ta ville dans le dossier de kaffeine.
Comme expliqué sur la page doc.ubuntu.com/materiel/tnt

puis dans dvb>configure il faut selectionner ta ville.

Pour moi ça n'a pas marché sans le fichier des fréquences.

manolito

Re : Pinnacle PCTV USB Stick et ubuntu

salut les petits gars

j'ai essayé avec tvtime et il m'indique no signal moi aussi j'ai essayé avec plusieurs antenne et je suis dans une zone couverte puisque j'ai 2 télé qui ont la tnt.

je ne suis pas sure d'avoir tout compris de l'histoire du fichier de configuration je vais de nouveau trainer de ce coté et je vous prévient d'un éventuel changement

@ très plus

Robinou

Re : Pinnacle PCTV USB Stick et ubuntu

En fait ma ville est déjà présente dans kaffeine (fr-Villebon) et j'habite à Bures-sur-Yvette, c'est-à-dire à moins de 5 km de Villebon! Donc ça devrait marcher nan ?

Sinon dans le dossier kaffeine, mon fr-Villebon donne :

#### VILLEBON SUR YVETTE ####
#R1 35
T 586000000 8MHz 3/4 NONE QAM64 8k 1/8 NONE
#R2 56
T 754000000 8MHz 2/3 NONE QAM64 8k 1/32 NONE
#R3 60
T 786000000 8MHz 2/3 NONE QAM64 8k 1/32 NONE
#R4 63
T 810000000 8MHz 2/3 NONE QAM64 8k 1/32 NONE
#R5 51
T 714000000 8MHz 2/3 NONE QAM64 8k 1/32 NONE
#R6 57
T 762000000 8MHz 2/3 NONE QAM64 8k 1/32 NONE

Et en comparant avec les autres du site doc.ubuntu.com/materiel/tnt, ça a l'air ok.
Là j'vois vraiment pas le problème!

ersplus

Re : Pinnacle PCTV USB Stick et ubuntu

essaye ca

#### VILLEBON SUR YVETTE ####
#R1 35
T 586167000 8MHz 3/4 NONE QAM64 8k 1/8 NONE
#R2 56
T 754167000 8MHz 2/3 NONE QAM64 8k 1/32 NONE
#R3 60
T 786167000 8MHz 2/3 NONE QAM64 8k 1/32 NONE
#R4 63
T 810167000 8MHz 2/3 NONE QAM64 8k 1/32 NONE
#R5 51
T 714167000 8MHz 2/3 NONE QAM64 8k 1/32 NONE
#R6 57
T 762166000 8MHz 2/3 NONE QAM64 8k 1/32 NONE

---

Voyager 11.10
Config : AMD Phenom II X4, 4 Go Ram, HDD 2 x 1 To
Wifi Netgear WNA1100

Robinou

Re : Pinnacle PCTV USB Stick et ubuntu

ça marche toujours pas ...en fait signal et smr restent tout le temps figés à 0% (c'est pas bon ça!).

si quelqu'un a une autre idée, j'suis chaud!

vectron

Re : Pinnacle PCTV USB Stick et ubuntu

Pour moi c'est au lancement deKAFEEINE avec
CAN T BIND INFO SOCKET ... ca correspond à quoi ?
Merci

Dernière modification par vectron (Le 21/12/2006, à 15:53)

---

Les pepites de Doc Brown : http://pepites80.blogspot.com/ - les années 80.

manolito

Re : Pinnacle PCTV USB Stick et ubuntu

@vectron

j'ai le même message et je cherche depuis un moment à quoi cela peut correspondre le premier qui à l'info previent l'autre.

merci

vectron

Re : Pinnacle PCTV USB Stick et ubuntu

ok pour te prevenir si j'ai des infos ... a+

---

Les pepites de Doc Brown : http://pepites80.blogspot.com/ - les années 80.

manolito

Re : Pinnacle PCTV USB Stick et ubuntu

j'essai d'installer une autre version de kaffeine que j'ai télécharger il s'agit d'un fichier tar.bz2 quel est la procédure pour l'installation de ce type de fichier

manolito

Re : Pinnacle PCTV USB Stick et ubuntu

l'orsque je selectionne dans kaffeine l'onglet dvb client ce dernier est vide cela ne me parait pas normal

Netizi

Re : Pinnacle PCTV USB Stick et ubuntu

Salut j'ai un probleme j'ai une erreur quand je fais:

sudo modprobe em2880-dvb
FATAL: Error inserting em2880_dvb (/lib/modules/2.6.17-10-generic/kernel/drivers/media/video/em28xx/em2880-dvb.ko): Unknown symbol in module, or unknown parameter (see dmesg)

J'ai essayé la methode dite un peu plus haut en modifiant le fichier dvb_net.c mais ça n'a rien changé...
Si quelqu'un à une idée...

Merci

david breizh

Re : Pinnacle PCTV USB Stick et ubuntu

essayer avec le v4l-dvb-kernel car je sais qu'il y a plusieurs version ou il n'y a pas ou de mauvais modules pour cette clé. et avec la mise à jour du noyau ça ne marche plus pour certains trucs donc soit vous rester avec l'ancienne soit comme moi vous compilez le noyau moi je suis en 2.6.18 et ça marche bien.

Dernière modification par david breizh (Le 24/12/2006, à 12:55)

---

ah ! du fin fond de la bretagne grâce au libre on se sent moins seul!
Vive le libre et toutes les distributions qui m'ont fait découvrir le monde de linux!

manolito

Re : Pinnacle PCTV USB Stick et ubuntu

voici ce que donne le dsmeg

je pense qu'il y a deschoses pas normale mais je ne comprend pas tout

[17179569.184000] Linux version 2.6.15-27-386 (buildd@terranova) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 PREEMPT Sat Sep 16 01:51:59 UTC 2006
[17179569.184000] BIOS-provided physical RAM map:
[17179569.184000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[17179569.184000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[17179569.184000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[17179569.184000]  BIOS-e820: 0000000000100000 - 0000000007ff0000 (usable)
[17179569.184000]  BIOS-e820: 0000000007ff0000 - 0000000007ff3000 (ACPI NVS)
[17179569.184000]  BIOS-e820: 0000000007ff3000 - 0000000008000000 (ACPI data)
[17179569.184000]  BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[17179569.184000] 0MB HIGHMEM available.
[17179569.184000] 127MB LOWMEM available.
[17179569.184000] On node 0 totalpages: 32752
[17179569.184000]   DMA zone: 4096 pages, LIFO batch:0
[17179569.184000]   DMA32 zone: 0 pages, LIFO batch:0
[17179569.184000]   Normal zone: 28656 pages, LIFO batch:7
[17179569.184000]   HighMem zone: 0 pages, LIFO batch:0
[17179569.184000] DMI 2.3 present.
[17179569.184000] ACPI: RSDP (v000 VIA694                                ) @ 0x000f7730
[17179569.184000] ACPI: RSDT (v001 VIA694 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x07ff3000
[17179569.184000] ACPI: FADT (v001 VIA694 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x07ff3040
[17179569.184000] ACPI: DSDT (v001 VIA694 AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
[17179569.184000] ACPI: PM-Timer IO Port: 0x4008
[17179569.184000] Allocating PCI resources starting at 10000000 (gap: 08000000:f7ff0000)
[17179569.184000] Built 1 zonelists
[17179569.184000] Kernel command line: root=/dev/hda2 ro quiet splash
[17179569.184000] Local APIC disabled by BIOS (or by default) -- you can enable it with "lapic"
[17179569.184000] mapped APIC to ffffd000 (01101000)
[17179569.184000] Initializing CPU#0
[17179569.184000] PID hash table entries: 512 (order: 9, 8192 bytes)
[17179569.184000] Detected 1000.203 MHz processor.
[17179569.184000] Using pmtmr for high-res timesource
[17179569.184000] Console: colour VGA+ 80x25
[17179573.320000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[17179573.324000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[17179573.332000] Memory: 119348k/131008k available (1976k kernel code, 11132k reserved, 606k data, 288k init, 0k highmem)
[17179573.332000] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[17179573.412000] Calibrating delay using timer specific routine.. 2002.29 BogoMIPS (lpj=4004591)
[17179573.412000] Security Framework v1.0.0 initialized
[17179573.412000] SELinux:  Disabled at boot.
[17179573.412000] Mount-cache hash table entries: 512
[17179573.412000] CPU: After generic identify, caps: 0183f9ff c1c7f9ff 00000000 00000000 00000000 00000000 00000000
[17179573.412000] CPU: After vendor identify, caps: 0183f9ff c1c7f9ff 00000000 00000000 00000000 00000000 00000000
[17179573.412000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[17179573.412000] CPU: L2 Cache: 256K (64 bytes/line)
[17179573.412000] CPU: After all inits, caps: 0183f9ff c1c7f9ff 00000000 00000420 00000000 00000000 00000000
[17179573.412000] mtrr: v2.0 (20020519)
[17179573.412000] CPU: AMD Athlon(tm) Processor stepping 02
[17179573.412000] Enabling fast FPU save and restore... done.
[17179573.412000] Checking 'hlt' instruction... OK.
[17179573.428000] checking if image is initramfs... it is
[17179574.520000] Freeing initrd memory: 6616k freed
[17179574.556000] ACPI: Looking for DSDT ... not found!
[17179574.556000] ACPI: setting ELCR to 0200 (from 0e20)
[17179574.560000] NET: Registered protocol family 16
[17179574.560000] EISA bus registered
[17179574.560000] ACPI: bus type pci registered
[17179574.576000] PCI: PCI BIOS revision 2.10 entry at 0xfb220, last bus=1
[17179574.576000] PCI: Using configuration type 1
[17179574.576000] ACPI: Subsystem revision 20051216
[17179574.588000] ACPI: Interpreter enabled
[17179574.588000] ACPI: Using PIC for interrupt routing
[17179574.588000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[17179574.588000] PCI: Probing PCI hardware (bus 00)
[17179574.588000] ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
[17179574.592000] PCI quirk: region 4000-40ff claimed by vt82c586 ACPI
[17179574.592000] PCI quirk: region 6000-607f claimed by vt82c686 HW-mon
[17179574.592000] PCI quirk: region 5000-500f claimed by vt82c686 SMB
[17179574.592000] Boot video device is 0000:01:00.0
[17179574.592000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[17179574.624000] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
[17179574.624000] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[17179574.624000] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
[17179574.624000] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
[17179574.628000] Linux Plug and Play Support v0.97 (c) Adam Belay
[17179574.628000] pnp: PnP ACPI init
[17179574.636000] pnp: PnP ACPI: found 12 devices
[17179574.636000] PnPBIOS: Disabled by ACPI PNP
[17179574.636000] PCI: Using ACPI for IRQ routing
[17179574.636000] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[17179574.664000] PCI: Bridge: 0000:00:01.0
[17179574.664000]   IO window: d000-dfff
[17179574.664000]   MEM window: d8000000-d9ffffff
[17179574.664000]   PREFETCH window: d4000000-d7ffffff
[17179574.664000] PCI: Setting latency timer of device 0000:00:01.0 to 64
[17179574.668000] audit: initializing netlink socket (disabled)
[17179574.668000] audit(1166984283.668:1): initialized
[17179574.668000] VFS: Disk quotas dquot_6.5.1
[17179574.668000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[17179574.668000] Initializing Cryptographic API
[17179574.668000] io scheduler noop registered
[17179574.668000] io scheduler anticipatory registered
[17179574.668000] io scheduler deadline registered
[17179574.668000] io scheduler cfq registered
[17179574.668000] PCI: Disabling Via external APIC routing
[17179574.668000] isapnp: Scanning for PnP cards...
[17179575.020000] isapnp: No Plug & Play device found
[17179575.044000] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[17179575.044000] serio: i8042 AUX port at 0x60,0x64 irq 12
[17179575.044000] serio: i8042 KBD port at 0x60,0x64 irq 1
[17179575.044000] Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
[17179575.044000] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179575.048000] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[17179575.048000] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179575.048000] 00:08: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[17179575.052000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[17179575.052000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[17179575.052000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[17179575.052000] mice: PS/2 mouse device common for all mice
[17179575.052000] EISA: Probing bus 0 at eisa.0
[17179575.052000] Cannot allocate resource for EISA slot 4
[17179575.052000] Cannot allocate resource for EISA slot 5
[17179575.052000] Cannot allocate resource for EISA slot 6
[17179575.052000] EISA: Detected 0 cards.
[17179575.052000] NET: Registered protocol family 2
[17179575.072000] input: AT Translated Set 2 keyboard as /class/input/input0
[17179575.092000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)[17179575.092000] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[17179575.092000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[17179575.092000] TCP: Hash tables configured (established 8192 bind 8192)
[17179575.092000] TCP reno registered
[17179575.092000] TCP bic registered
[17179575.092000] NET: Registered protocol family 1
[17179575.092000] NET: Registered protocol family 8
[17179575.092000] NET: Registered protocol family 20
[17179575.092000] Using IPI Shortcut mode
[17179575.092000] ACPI wakeup devices:
[17179575.092000] SLPB PCI0 USB0 USB1 MODM UAR1 UAR2 ECP1
[17179575.092000] ACPI: (supports S0 S1 S4 S5)
[17179575.092000] Freeing unused kernel memory: 288k freed
[17179575.188000] vga16fb: initializing
[17179575.188000] vga16fb: mapped to 0xc00a0000
[17179575.244000] Console: switching to colour frame buffer device 80x25
[17179575.244000] fb0: VGA16 VGA frame buffer device
[17179576.416000] Capability LSM initialized
[17179576.480000] ACPI: CPU0 (power states: C1[C1] C2[C2])
[17179576.480000] ACPI: Processor [CPU0] (supports 2 throttling states)
[17179577.464000] VP_IDE: IDE controller at PCI slot 0000:00:07.1
[17179577.464000] PCI: Via IRQ fixup for 0000:00:07.1, from 255 to 0
[17179577.464000] VP_IDE: chipset revision 16
[17179577.464000] VP_IDE: not 100% native mode: will probe irqs later
[17179577.464000] VP_IDE: VIA vt82c686a (rev 22) IDE UDMA66 controller on pci0000:00:07.1
[17179577.464000]     ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:pio
[17179577.464000]     ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:DMA
[17179577.464000] Probing IDE interface ide0...
[17179577.880000] hda: ST340014A, ATA DISK drive
[17179578.552000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[17179578.552000] Probing IDE interface ide1...
[17179579.416000] hdc: CRD-8322B, ATAPI CD/DVD-ROM drive
[17179580.200000] hdd: PHILIPS CDRW1610A, ATAPI CD/DVD-ROM drive
[17179580.256000] ide1 at 0x170-0x177,0x376 on irq 15
[17179580.272000] hda: max request size: 1024KiB
[17179580.296000] hda: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(66)
[17179580.300000] hda: cache flushes supported
[17179580.300000]  hda: hda1 hda2 hda3 < hda5 >
[17179580.344000] hdc: ATAPI 32X CD-ROM drive, 128kB Cache, DMA
[17179580.344000] Uniform CD-ROM driver Revision: 3.20
[17179580.348000] hdd: ATAPI 40X CD-ROM CD-R/RW drive, 8192kB Cache, UDMA(33)
[17179580.724000] usbcore: registered new driver usbfs
[17179580.728000] usbcore: registered new driver hub
[17179580.728000] USB Universal Host Controller Interface driver v2.3
[17179580.732000] **** SET: Misaligned resource pointer: c689a2e2 Type 07 Len 0
[17179580.732000] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
[17179580.732000] PCI: setting IRQ 5 as level-triggered
[17179580.732000] ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
[17179580.732000] uhci_hcd 0000:00:07.2: UHCI Host Controller
[17179580.732000] uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
[17179580.732000] uhci_hcd 0000:00:07.2: irq 5, io base 0x0000e400
[17179580.732000] hub 1-0:1.0: USB hub found
[17179580.732000] hub 1-0:1.0: 2 ports detected
[17179580.784000] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
[17179580.836000] ACPI: PCI Interrupt 0000:00:07.3[D] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
[17179580.836000] uhci_hcd 0000:00:07.3: UHCI Host Controller
[17179580.836000] uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
[17179580.836000] uhci_hcd 0000:00:07.3: irq 5, io base 0x0000e800
[17179580.836000] hub 2-0:1.0: USB hub found
[17179580.836000] hub 2-0:1.0: 2 ports detected
[17179580.940000] **** SET: Misaligned resource pointer: c7dd9c02 Type 07 Len 0
[17179580.940000] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
[17179580.940000] PCI: setting IRQ 10 as level-triggered
[17179580.940000] ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
[17179580.944000] ohci_hcd 0000:00:0f.0: OHCI Host Controller
[17179580.944000] ohci_hcd 0000:00:0f.0: new USB bus registered, assigned bus number 3
[17179580.944000] ohci_hcd 0000:00:0f.0: irq 10, io mem 0xda000000
[17179581.028000] hub 3-0:1.0: USB hub found
[17179581.028000] hub 3-0:1.0: 3 ports detected
[17179581.076000] usb 1-1: new full speed USB device using uhci_hcd and address 2
[17179581.132000] ACPI: PCI Interrupt 0000:00:0f.1[b] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
[17179581.132000] ohci_hcd 0000:00:0f.1: OHCI Host Controller
[17179581.132000] ohci_hcd 0000:00:0f.1: new USB bus registered, assigned bus number 4
[17179581.132000] ohci_hcd 0000:00:0f.1
: irq 5, io mem 0xda001000
[17179581.216000] hub 4-0:1.0: USB hub found
[17179581.216000] hub 4-0:1.0: 2 ports detected
[17179581.232000] usb 1-1: configuration #2 chosen from 2 choices
[17179581.320000] **** SET: Misaligned resource pointer: c7dd9502 Type 07 Len 0
[17179581.324000] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
[17179581.324000] PCI: setting IRQ 11 as level-triggered
[17179581.324000] ACPI: PCI Interrupt 0000:00:0f.2[C] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[17179581.324000] ehci_hcd 0000:00:0f.2: EHCI Host Controller
[17179581.348000] ehci_hcd 0000:00:0f.2: new USB bus registered, assigned bus number 5
[17179581.348000] ehci_hcd 0000:00:0f.2: irq 11, io mem 0xda002000
[17179581.348000] ehci_hcd 0000:00:0f.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[17179581.348000] hub 5-0:1.0: USB hub found
[17179581.348000] hub 5-0:1.0: 5 ports detected
[17179581.616000] Attempting manual resume
[17179581.672000] EXT3-fs: mounted filesystem with ordered data mode.
[17179581.700000] kjournald starting.  Commit interval 5 seconds
[17179582.864000] usb 4-1: new full speed USB device using ohci_hcd and address 2
[17179583.076000] hub 4-1:1.0: USB hub found
[17179583.080000] hub 4-1:1.0: 4 ports detected
[17179583.508000] usb 4-2: new full speed USB device using ohci_hcd and address 3
[17179584.036000] usb 3-2: new full speed USB device using ohci_hcd and address 2
[17179595.376000] parport_pc: VIA 686A/8231 detected
[17179595.376000] parport_pc: probing current configuration
[17179595.376000] parport_pc: Current parallel port base: 0x378
[17179595.376000] parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
[17179595.388000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[17179595.392000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[17179595.472000] parport_pc: VIA parallel port: io=0x378, irq=7
[17179595.960000] Linux agpgart interface v0.101 (c) Dave Jones
[17179596.048000] agpgart: Detected VIA Twister-K/KT133x/KM133 chipset
[17179596.056000] agpgart: AGP aperture is 64M @ 0xd0000000
[17179596.216000] Real Time Clock Driver v1.12
[17179596.344000] ACPI: PCI Interrupt 0000:00:11.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
[17179596.804000] input: ImPS/2 Logitech Wheel Mouse as /class/input/input1
[17179597.216000] input: PC Speaker as /class/input/input2
[17179597.256000] eth0: register 'cdc_ether' at usb-0000:00:07.2-1, CDC Ethernet Device, 00:16:ae:cf:f4:9b
[17179597.256000] usbcore: registered new driver cdc_ether
[17179598.300000] ts: Compaq touchscreen protocol output
[17179598.352000] Floppy drive(s): fd0 is 1.44M
[17179598.368000] FDC 0 is a post-1991 82077
[17179598.564000] drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x043D pid 0x0078
[17179598.564000] usbcore: registered new driver usblp
[17179598.564000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[17179599.208000] lp0: using parport0 (interrupt-driven).
[17179599.284000] CSLIP: code copyright 1989 Regents of the University of California
[17179599.308000] PPP generic driver version 2.4.2
[17179599.428000] Linux video capture interface: v1.00
[17179599.504000] em28xx v4l2 driver version 0.0.1 loaded
[17179599.508000] usbcore: registered new driver em28xx
[17179599.732000] /usr/src/v4l-dvb/v4l/mt2060-tuner.c: mt2060_module_init
[17179599.848000] Adding 369452k swap on /dev/hda5.  Priority:-1 extents:1 across:369452k
[17179599.908000] NET: Registered protocol family 17
[17179600.036000] EXT3 FS on hda2, internal journal
[17179600.308000] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
[17179600.308000] md: bitmap version 4.39
[17179600.960000] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
[17179601.448000] cdrom: open failed.
[17179601.940000] cdrom: open failed.
[17179601.948000] cdrom: open failed.
[17179603.496000] NET: Registered protocol family 10
[17179603.496000] lo: Disabled Privacy Extensions
[17179603.496000] IPv6 over IPv4 tunneling driver
[17179613.540000] eth0: no IPv6 routers present
[17179631.868000] ACPI: Power Button (FF) [PWRF]
[17179631.868000] ACPI: Power Button (CM) [PWRB]
[17179631.868000] ACPI: Sleep Button (CM) [SLPB]
[17179632.088000] ibm_acpi: ec object not found
[17179632.144000] pcc_acpi: loading...
[17179632.980000] powernow: No powernow capabilities detected
[17179636.836000] [drm] Initialized drm 1.0.1 20051102
[17179636.868000] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[17179636.872000] [drm] Initialized radeon 1.24.0 20060225 on minor 0
[17179637.956000] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[17179637.956000] agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
[17179637.956000] agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
[17179638.332000] [drm] Setting GART location based on new memory map
[17179638.332000] [drm] writeback test succeeded in 1 usecs
[17179639.288000] ppdev: user-space parallel port driver
[17179639.816000] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[17179639.816000] apm: overridden by ACPI.
[17179646.460000] Bluetooth: Core ver 2.8
[17179646.460000] NET: Registered protocol family 31
[17179646.460000] Bluetooth: HCI device and connection manager initialized
[17179646.460000] Bluetooth: HCI socket layer initialized
[17179646.520000] Bluetooth: L2CAP ver 2.8
[17179646.520000] Bluetooth: L2CAP socket layer initialized
[17179646.528000] Bluetooth: RFCOMM socket layer initialized
[17179646.528000] Bluetooth: RFCOMM TTY layer initialized
[17179646.528000] Bluetooth: RFCOMM ver 1.7

david breizh

Re : Pinnacle PCTV USB Stick et ubuntu

toi il te manque le module em2880-dvb non? et je crois que ça vient de la version du v4l que tu as utiliser .

---

ah ! du fin fond de la bretagne grâce au libre on se sent moins seul!
Vive le libre et toutes les distributions qui m'ont fait découvrir le monde de linux!

cabrito

Re : Pinnacle PCTV USB Stick et ubuntu

Salut,
en plus du module dvb, il manque à coup sur les balises « Code ».

Bonne continuation...

manolito

Re : Pinnacle PCTV USB Stick et ubuntu

desolé pour les balises code

atlas95

Re : Pinnacle PCTV USB Stick et ubuntu

Bonjour, bonne année, meilleurs voeux

J'ai une carte PCTV Hybrid Pro USB (pctv 330e), acheter il y a une semaine.
Quand je fais un lsusb, elle est reconnu comme:

Bus 005 Device 006: ID 2304:0226 Pinnacle Systems, Inc. [hex]

Apres avoir fait un modprobe em28xx,
J'ai le "dmesg" suivant:

[17182490.292000] em28xx new video device (2304:0226): interface 0, class 255
[17182490.292000] em28xx: device is attached to a USB 2.0 bus
[17182490.292000] em28xx #0: Alternate settings: 8
[17182490.292000] em28xx #0: Alternate setting 0, max size= 0
[17182490.292000] em28xx #0: Alternate setting 1, max size= 0
[17182490.292000] em28xx #0: Alternate setting 2, max size= 1448
[17182490.292000] em28xx #0: Alternate setting 3, max size= 2048
[17182490.292000] em28xx #0: Alternate setting 4, max size= 2304
[17182490.292000] em28xx #0: Alternate setting 5, max size= 2580
[17182490.292000] em28xx #0: Alternate setting 6, max size= 2892
[17182490.292000] em28xx #0: Alternate setting 7, max size= 3072
[17182491.292000] input: em2880/em2870 remote control as /class/input/input5
[17182491.292000] em28xx-input.c: remote control handler attached
[17182491.292000] attach_inform: eeprom detected.
[17182491.320000] em28xx #0: i2c eeprom 00: 1a eb 67 95 04 23 26 02 d0 12 5c 03 8e 16 a4 1c
[17182491.320000] em28xx #0: i2c eeprom 10: 6a 24 27 57 46 07 01 00 00 00 00 00 00 00 00 00
[17182491.320000] em28xx #0: i2c eeprom 20: 46 00 01 00 f0 10 02 00 b8 00 00 00 5b e0 00 00
[17182491.320000] em28xx #0: i2c eeprom 30: 00 00 20 40 20 6e 02 20 10 01 00 00 00 00 00 00
[17182491.320000] em28xx #0: i2c eeprom 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[17182491.320000] em28xx #0: i2c eeprom 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[17182491.320000] em28xx #0: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 24 03 50 00 69 00
[17182491.320000] em28xx #0: i2c eeprom 70: 6e 00 6e 00 61 00 63 00 6c 00 65 00 20 00 53 00
[17182491.320000] em28xx #0: i2c eeprom 80: 79 00 73 00 74 00 65 00 6d 00 73 00 00 00 16 03
[17182491.320000] em28xx #0: i2c eeprom 90: 50 00 43 00 54 00 56 00 20 00 33 00 33 00 30 00
[17182491.320000] em28xx #0: i2c eeprom a0: 65 00 00 00 1c 03 30 00 36 00 31 00 30 00 30 00
[17182491.320000] em28xx #0: i2c eeprom b0: 31 00 30 00 35 00 37 00 34 00 37 00 31 00 00 00
[17182491.320000] em28xx #0: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[17182491.320000] em28xx #0: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[17182491.320000] em28xx #0: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[17182491.320000] em28xx #0: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[17182491.320000] EEPROM ID= 0x9567eb1a
[17182491.320000] Vendor/Product ID= 2304:0226
[17182491.320000] AC97 audio (5 sample rates)
[17182491.320000] 500mA max power
[17182491.320000] Table at 0x27, strings=0x168e, 0x1ca4, 0x246a
[17182491.320000] tuner 0-0061: chip found @ 0xc2 (em28xx #0)
[17182491.320000] attach inform (default): detected I2C address c2
[17182491.328000] Tuner: setting up tuner core extension for: Xceive 3028 Tuner
[17182491.328000] Loading base firmware: xc3028_init0.i2c.fw
[17182492.420000] Loading default analogue TV settings: xc3028_BG_PAL_A2_A.i2c.fw
[17182492.448000] attach_inform: tvp5150 detected.
[17182492.512000] tvp5150 0-005c: tvp5150am1 detected.
[17182492.600000] em28xx-video.c: requesting em28xx-audio!
[17182492.600000] em28xx-video.c: requesting em2880-dvb!
[17182492.604000] em28xx #0: V4L2 VBI device registered as /dev/vbi0
[17182492.608000] em28xx #0: V4L2 device registered as /dev/video0
[17182492.608000] em2880-dvb.c: DVB Init
[17182492.608000] em2880-dvb.c: unsupported device
[17182492.608000] em2880-dvb.c: failed initializing zl10353 DVB-T demodulator
[17182492.608000] em2880-dvb.c: retrying with mt352 DVB-T demodulator
[17182492.608000] FIXME: Write failed, backtrace:
[17182492.608000] ===============================
[17182492.608000] 7f 
[17182492.608000] ================================
[17182492.608000] mt352_read_register: readreg error (reg=127, ret==-19)
[17182492.608000] em2880-dvb.c: no luck with mt352 demodulator, not attaching em2880-dvb
[17182492.608000] em2880-dvb.c: DVB-T demodulator not reachable, did you try "modprobe em28xx device_mode=1"
[17182492.608000] em28xx #0: Found Pinnacle Hybrid Pro (2)

>> http://pastebin.com/849797

J'ai évidemment try la proposition avec device_mode=1 mais ca me dit la meme chose ...

Pourriez vous m'aider?
Merci d'avance de votre aide

Dernière modification par atlas95 (Le 02/01/2007, à 22:09)

---

Ubuntu sur un XPS m1330:c'est ici !
Mon blog sur ubuntu:c'est ici !
Jabber : cyril at jabber.levis-heb.net

Fein

Re : Pinnacle PCTV USB Stick et ubuntu

Bien le bonjour et bonne année a tous,

bon voila je viens d'acquerire une pinnacle PCTV USB Stick.

Quand je fait une recherche de chaine il m'en trouve seulement 3 et j'ai une reception a plus de 90 mais pourtant il ne se passe rien

Je suis sous windows Xp Famille.

Merci de votre aide.

atlas95

Re : Pinnacle PCTV USB Stick et ubuntu

Bonjour fein, ceci est un forum ubuntu (linux) =/= windows.
Vois peux etre au niveau de l'antenne...

---

Ubuntu sur un XPS m1330:c'est ici !
Mon blog sur ubuntu:c'est ici !
Jabber : cyril at jabber.levis-heb.net

Fein

Re : Pinnacle PCTV USB Stick et ubuntu

Oui cela je sais mais je ne trouve rien d'autre que votre forum ...

Non je ne crois pas que cela vienne de cela mais bon merci kan meme

atlas95

Re : Pinnacle PCTV USB Stick et ubuntu

Up!

---

Ubuntu sur un XPS m1330:c'est ici !
Mon blog sur ubuntu:c'est ici !
Jabber : cyril at jabber.levis-heb.net

manolito

Re : Pinnacle PCTV USB Stick et ubuntu

@atlas95

salut

je n'arrive toujours pas sous ubuntu mais cela va venir par contre j'ai essayer avec windows cela marche impeccable mais avec une antenne de toit pas avec la mini antenne fournie
alors je serais toi je chercherais du coté de l'antenne
autre conseil laisse tombé windows et rejoint les ubuntunautes au debut c'est compliqué mais plus on avance plus on est satisfait

nicolas_serre

Re : Pinnacle PCTV USB Stick et ubuntu

Voici comment faire fonctionner la carte Pinnacle PCTV USB Stick en analogique (image+son):
- suivre les explications de Gouchi :
http://forum.ubuntu-fr.org/viewtopic.ph … 15#p323215
- télécharger le script à l'adresse suivante pour vous aider à avoir le son facilement en analogique: http://linuxtv.org/hg/~mrechberger/v4l- … ;style=raw
Lancer xawtv, puis exécuter v4l-scripts-usbaudio_setup.sh dans un terminal.
Si à l'execution du script, vous avez le message d'erreur suivant:

sox: Can't open output file '/dev/dsp': Device or resource busy

Il suffit de taper la commande suivante avant de relancer le script:

sudo killall esd

Dans un autre terminal taper:

alsamixer -c 1 -V capture

et muter puis réactiver l'audio (espace x2), et sortie.

Seul problème notable et pas des moindre pour moi, ma webcam dont le pilote est gspca, ne supporte pas le nouveau v4l. Le module correspondant n'est plus chargé et je me retrouve avec la TNT mais sans webcam !! Ce problème est d'ailleurs signalé dans la documentation, espérons qu'une solution soit trouvée rapidement.

[EDIT]
Pour plus de précision sur le son en analogique, aller voir là:
http://forum.ubuntu-fr.org/viewtopic.php?id=85468

Dernière modification par nicolas_serre (Le 11/02/2007, à 22:03)